FIREPLACE KITS
AND ACCESSORIES
750,210M
Rev. A 07/2006
BI-FOLD GLASS DOORS
INSTALLATION INSTRUCTIONS FOR OUTDOOR BI-FOLD GLASS DOORS
MODELS: 36BFOD-BS & 42BFOD-BS
INSTALLATION INSTRUCTIONS
Remove Screens And Rods:
Using a 5/16" socket or nutdriver, remove the screen rod assemblies
(see Figure 1 ). Remove the screen rod screws as shown in Figure 1.
Pull out the rods from locating holes on the side of the firebox opening.
IMPORTANT! REINSTALL SCREEN ROD SCREWS INTO THE EXISTING
HOLES WHERE REMOVED.
The screen and rod assemblies must not be installed when the Bi-Fold
Glass Door Kit is installed. You may wish to retain the screen and rod
assembliesiscasetheBi-FoldGlassDoorKitiseverremovedinthefuture.
IMPORTANT! IF THIS OPTIONAL BI-FOLD GLASS DOOR KIT IS EVER
REMOVED, THE ROD AND SCREENS MUST BE REINSTALLED FOR
SAFE OPERATION OF THE APPLIANCE.
These bi-fold glass door assemblies have been designed for use with and
may be easily fitted to your Lennox Outdoor Gas Fireplace, Models
E36ODG & E42ODG.
Do not alter or modify these door assemblies or a fireplace malfunction
or a fire hazard may result.
These doors have been tested and listed by Omni-Test Laboratories
Inc.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
GENERAL INFORMATION
Thedoorassemblyconsistsofarightandleftglasspanelassemblywiththe
door handles factory mounted. Included is a four piece door frame with
eight(8)screwsandahood(hoodpackagedseparately),whicharerequired
for assembly. Fireplaces listed on the front page of this document, have
been designed to accept these doors with minimum effort.
Screen Rod
Screws
TOOLS REQUIRED
Screen And
Rod Assembly
• Medium Phillips Screwdriver • 3/8" Open-end wrench
• 1/4" Drive Socket
Figure 1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: THEFINISHOFTHESEDOORSMAYBEPROTECTEDWITH
A SELF ADHERING PLASTIC COATING THAT MUST BE REMOVED
BEFOREHEATISGENERATEDBYAFIREINTHEFIREBOX. TOPREVENT
MELTING, ENSURE THAT ANY PLASTIC COATING PROTECTING THE
FINISH OF THESE DOORS IS REMOVED FOLLOWING INSTALLATION.
REFER TO THE FIREPLACE INSTALLATION AND HOMEOWNER'S IN-
STRUCTIONS FOR DETAILED INSTRUCTIONS REGARDING THE MAIN-
TENANCE OF THE FINISH OF THESE DOORS.
CAUTION: THE FRONT-OPEN FIREPLACE OR APPLIANCE SHOULD
ONLYBEOPERATEDWITHTHEGLASSDOORSFULLYOPENORFULLY
CLOSED (SEE FIGURE 8 ).
Lower
Pivot Pin
Figure 6
CAUTION: GLASS AND METAL FRAMES GET HOT — ALWAYS USE
HANDLES TO OPEN AND CLOSE THE DOORS.
Step 2. Tilt the top of the door into place and carefully ensure that the
upper pivot pin and roller pin is in the upper door guide track.
Step 3. Continue to tilt the top of the door into place until the upper
pivot pin engages the spring clip and the pivot pin locks into place
within the hole of the spring clip (see Figure 7 ).
Step 4. Repeat this procedure for the opposite door assembly.
Spring Clip
Upper Door
Guide Track
Fully Open or
Fully Closed
Front-Open Systems
Pivot Pin
Roller Pin
Figure 8
CLEANING
NEVER CLEAN THE GLASS WHEN THE DOORS ARE HOT. DO NOT USE
AMMONIAORANYAMMONIABASEDGLASSORHOUSEHOLDCLEANER
TO CLEAN THE GLASS OR THE DOOR FRAME. AN AMMONIA BASED
CLEANER WILL DAMAGE THE FINISH.
Remove dirt and grime from the doors using a clean dampened towel
followed by wiping with a dry towel. To remove stubborn stains from the
doors, use a mild soap solution and towel to gently scrub away stain.
Take care not to scratch the glass surface. Do not use abrasive cleaners.
Figure 7
ADJUSTMENT FOR DOOR ALIGNMENT
The doors are properly adjusted when the top door trim is in a straight,
level line and the gap between the doors is even at the top and bottom. If
adjustments are required, grasp the door handle and loosen the lower
door pivot pin using a ³⁄₈" open end wrench*. Slide the door panel on the
hinge pin until the gap between the upper door trim and upper frame is
even. Retighten the lower door pivot pin*. Repeat this procedure for the
opposite door if needed.
IMPORTANT: THESE GLASS DOORS UTILIZE TEMPERED GLASS
WHICH IS DESIGNED FOR USE WITH HIGH TEMPERATURES BUT CAN
UNEXPECTEDLY SHATTER. DO NOT SIT CLOSE TO THE GLASS.
Tempered glass will break into small particles if it should shatter
unexpectedly. If the glass breaks, particles of extremely hot glass could
be discharged into the surrounding environment, thereby creating a risk
ofpersonalinjuryorfire. Observationoftheaboveoperatingprecautions
and instructions will reduce the risk of personal injury or fire.
*Note: Upper door pivot pins can also be loosened for adjustment
purposes; however, it is easier to loosen lower pins.
If the tempered glass pane becomes scratched or chipped, it creates a
weakness in the glass which can cause the glass to break when heated.
Replace the pane of glass by contacting your nearest distributor or
dealer.
GENERAL OPERATING PRECAUTIONS AND INSTRUCTIONS
CAUTION: THESE GLASS DOORS ARE LISTED ONLY FOR USE WITH
THE FIREPLACE OR APPLIANCE MODELS SHOWN ON THE FRONT
PAGE. USE ON ANY OTHER FIREPLACE OR APPLIANCE MAY CONSTI-
TUTE A POTENTIAL FIRE HAZARD.
• Use fireplace tools carefully to avoid striking the glass.
• Keep wire mesh screens closed during fireplace use.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2006 by Lennox Hearth Products
1110 West Taft Avenue
P/N 750,210M REV. A 07/2006
Orange, CA 92865
Download from Www.Somanuals.com. All Manuals Search And Download.
|