Seed Bed Roller
Model SBR48, SBR60 & SBR72
Without Pull Hitch Option
25763
With Pull Hitch Option
25762
322-215M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
© Copyright 2008 Printed
2/23/09
Cover photo may show optional equipment
not supplied with standard unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
L
Land Pride
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved in
the operation, transport, maintenance and storage of
equipment.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
!
L Operator should be familiar with
!
Be Aware of
Signal Words
WARNING
all functions of the unit.
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
L Operate implement from the
driver’s seat only.
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
L Make sure all guards and shields
are in place and secured before
operating the implement.
L Do not leave tractor or implement
!
DANGER
unattended with engine running.
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
CAUTION
L Dismounting from a moving
tractor could cause serious injury
or death.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
L Do not stand between the tractor
and implement during hitching.
L Keep hands, feet, and clothing
away from power-driven parts.
L Wear snug fitting clothing to avoid
entanglement with moving parts.
L Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
For Your Protection
Shutdown and Storage
L Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
L Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
L Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
L Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
OFF
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
1
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
L Use the following maximum
Use Safety
Lights and Devices
Transport
Machinery Safely
speed - tow load weight ratios as
a guideline:
L 20 mph when weight is less than
L Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.
L Comply with state and local laws.
or equal to the weight of tractor.
L Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
L Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
L 10 mph when weight is double
the weight of tractor.
L IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
L Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
L Do not grease or oil implement
Use A Safety Chain
Practice Safe Maintenance
L Understand procedure before doing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
L Work in a clean dry area.
L Lower the implement to the ground,
put tractor in park, turn off engine,
and remove key before performing
maintenance.
while it is in operation.
L A safety chain will help control
drawn machinery should it
separate from the tractor
drawbar.
L Use a chain with the strength
rating equal to or greater than
the gross weight of the towed
machinery.
L Attach the chain to the tractor
drawbar support or other
specified anchor location. Allow
only enough slack in the chain
to permit turning.
L Inspect all parts. Make sure parts
are in good condition & installed
properly.
L Remove buildup of grease, oil or
debris.
L Remove all tools and unused
parts from implement before
operation.
L Allow implement to cool completely.
L Do not use safety chain for
towing.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
2
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Avoid High
Pressure Fluids Hazard
Wear
Prepare for Emergencies
L Be prepared if a fire starts.
Protective Equipment
L Escaping fluid under pressure can
penetrate the skin causing serious
injury.
L Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
L Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
L Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
L Protective clothing and equipment
L Keep a first aid kit and fire
should be worn.
extinguisher handy.
L Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
L Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
L Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
L Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
L Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
L If an accident occurs, see a
doctor immediately. Any fluid
injected into the skin must be
treated within a few hours or
gangrene may result.
911
Keep Riders
Off Machinery
L Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
Tire Safety
Handle
Chemicals Properly
L Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
L When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
L Protective clothing should be
worn.
L Handle all chemicals with care.
L Follow instructions on container
L Never allow children to operate
label.
equipment.
L Agricultural chemicals can be
dangerous. Improper use can
seriously injure persons, animals,
plants, soil, and property.
L Inhaling smoke from any type of
chemical fire is a serious health
hazard.
L When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
L Store or dispose of unused
chemicals as specified by the
chemical manufacturer.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
3
Land Pride
Important Safety Information
Safety Labels
Your Seed Bed Roller comes equipped with all safety
labels in place. They were designed to help you safely
operate your implement. Read and follow their
directions.
1. Keep all safety labels clean and legible.
2. Replace all damaged or missing labels. To order new
labels go to your nearest Land Pride dealer or visit our
dealer locator at landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
4. Refer to this section for proper label placement.
To install new labels:
a. Clean the area the label is to be placed.
b. Spray soapy water on the surface where the label is to
be placed.
c. Peel backing from label. Press firmly onto the surface.
d. Squeeze out air bubbles with the edge of a credit card.
848-148C
Above Tongue
Negative Hitch Weight
Located below and above the tongue.
Below Tongue
25762
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners. This Seed Bed Roller has been
designed with care and built by skilled workers using
quality materials. Proper assembly, maintenance and
safe operating practices will help you get years of
satisfactory use from the machine.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
Application
NOTE: A special point of information that the
operator must be aware of before continuing.
The Land Pride SBR48, SBR60 and SBR72 Three-point
hitch or Pull-Type Seed Bed Rollers have uses and
applications in landscaping, sports field maintenance,
pasture maintenance, professional turf care, general
seeding and overseeding applications around home
sites, construction sites, horse paddocks, nurseries, sod
farms, and small farm or ranch operations. These Seed
Bed Rollers will break up smaller clumps and dirt clods,
while pressing applied seed into firm contact with the soil
profile for greatly improved germination rates. The
notched profile of the rollers also develops a pattern of
uniformly spaced mini-furrows that tend to hold seed and
fertilizer in place. These small furrows also retain
essential moisture, and resist erosion from the wind and
the runoff from applied irrigation or rain.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Seed Bed
Roller.
The Seed Bed Roller also can also serve as the roller
packer attachment of Land Pride’s complimented
Seeder/Overseeder system. This system is comprised of
a Land Pride Disc Harrow with a rear mounted Spin
Spreader and special hitch kit, a trailing 6’ x 4’ DRG06
Drag Harrow, and trailing Pull-type SBR72 Seed Bed
Roller. This componentized Seeder/Overseeder system
provides for one-pass ground cultivation and seed to soil
integration for applications on previously tilled soil,
existing pasture ground, large grassy areas, reclamation
sites, or wild game food plots.
The parts on your Seed Bed Roller have been specially
designed and should only be replaced with genuine Land
Pride parts. Therefore should your Seed Bed Roller
require replacement parts go to your Land Pride Dealer.
Serial Number Plate
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure to include your serial and model numbers
in correspondence also. Refer to Figure 1 for the location
of your serial number plate.
for additional information and performance enhancing
options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
25763
Serial Number Plate Location
Figure 1
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Introduction
Further Assistance
Your dealer wants you to be satisfied with your new Seed
Bed Roller. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Tractor Requirements
Three Point Hitch Assembly
The tractor horsepower and weight must be capable of
controlling the Seed Bed Roller under all operating
conditions. Smaller horsepower and lighter weight
tractors must not be used.
on page 21 when tightening hardware.
Refer to Figure 1-1:
1. Chock front and back of rollers to prevent unit from
shifting while assembling the hitch assembly.
Three-Point Hook-up
A Category I hitch with 7/8” dia. holes in the lower hitch
links and 3/4” dia. hole in the top link is required. The
lower 3-point arms must be stabilized to prevent side-to-
side movement. Most tractors have sway blocks or
adjustable chains for this purpose. A Category I Land
Pride Quick Hitch can be used with the implement.
2. Attach support stand (#3) to clevis plate with 5/8"
wire snap lock pin (#10). Make certain notch “A” is
located against the square tubing corner as shown.
3. Attach bottom of hitch frame (#4) to clevis plates with
two 5/8"-11 x 1 1/2" GR5 round head square neck
bolts (#6) and 5/8" hex flange lock nuts (#7). Draw
nuts up snug, do not tighten.
Horsepower requirements. . . . . . . . . . . . . . .18 - 50 hp.
Minimum tractor weight . . . . . . . . . . . . . . . . . . 700 lbs.
4. Attach upper two holes in hitch frame to clevis plates
with hitch pins (#1) and linch pins (#9)
Pull Type Hook-Up
5. Install 3/4"-10 x 3 1/2" GR5 hex head cap screw
(#5A) with 1 1/4" x 2" spacer (#2) and 3/4" hex flange
lock nut (#7). Tighten nut to the correct torque.
The Pull Type Model is set-up with a 2" ball hitch and a
clevis type hitch.
Pull-type HP. . . . . . . . . . . . . . . . . . . . . . . . . .18 - 50 hp.
6. Install 3/4"-10 x 3 1/2" GR5 hex head cap
screw (#5B) and 3/4" hex flange lock nut (#8).
Draw nut up snug.
7. Tighten 5/8" hex flange lock nuts (#7) to the corrrect
torque.
25773
Three point Hitch Assembly
Figure 1-1
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
7
Land Pride
Section 1: Assembly & Set-up
c. Attach back of tongue with two 3/8"-16 x 1" GR5
cap screws (#8) and 3/8" flange lock nuts (#15).
Pull Type Hitch Assembly (Optional)
on page 21 when tightening hardware.
7. Tighten flange lock nuts (#14, #15 & #16) to the
correct torques.
1. Chock front and back of rollers to prevent unit from
shifting. Support 2" square tube frame up so that the
top of the clevis plates are level.
hitch (#7) can be installed with either hitch facing
forward. Determine which hitch you intend to use
and face that hitch forward.
2. Remove support stand (#3) and wire snap lock
pin (#1A) from the clevis plates (shipping location).
8. Remove wire snap lock pin (#1B). Reorient ball
hitch (#6) and clevis hitch (#7) with preferred hitch
facing forward and then reattach hitch to tongue (#5)
with wire snap lock pins (#1A & 1B).
3. The front two holes in hitch frame (#4) should be
shipped from the factory attached to the front holes
in the clevis plates with hitch pins (#17) and linch
pins (#11). If not, make this pin connection now.
9. Attach support stand (#3) to wire snap lock pin (#1A).
When not in use, rotate stand up and secure in place
with second wire snap lock pin (#1B).
4. Rotate hitch frame (#4) down to align rear holes in
hitch frame with holes at the back of the clevis plates.
Insert 5/8"-11 x 1 1/2" GR5 carriage bolts (#10) and
secure with 5/8" hex flange lock
10. If clevis hitch (#7) is facing forward, insert 3/4" hitch
pin (#12) and secure with hair pin cotter (#13). If ball
hitch (#6) is facing forward, store hitch pin and hair
pin cotter in a safe location of your choosing.
nuts (#16). Draw nuts up snug, do not tighten.
5. Remove 3/4" hex cap screws (#9), 2" spacer (#2) and
and 3/8" cap screws (#8) from hitch frame (#4).
Roller Scraper Assembly
IMPORTANT: The tongue (#5) should be as near
level as possible when pulling the roller over soil.
Before proceeding, determine which hitch assembly
below to use that will mount the tongue near level.
on page 21 when tightening hardware.
Refer to Figure 1-4 on page 9:
1. Attach roller scraper assembly to the Seed Bed
Roller frame with 3/8"-16 x 1" GR5 round head
square neck bolts (#2) and hex flange lock nuts (#3).
tongue (#5) if tractor drawbar is lower than 13"
2. Tighten nuts to the correct torque.
tongue (#5) if tractor drawbar is 13" or higher.
3. Some adjustment to the scraper teeth can be made
by loosening the nuts on scraper (#1). Retighten nuts
after adjustment has been made. See “Scraper Bar
Adjustment” on page 11 for detailed instructions.
6. Attach tongue (#5) to 3-point hitch (#4) as follows:
a. Remove bolts (#8) from back of tongue (#5).
b. Attach middle of tongue to hitch (#2) with two
3/4"-10 x 3 1/2" GR5 cap screws (#9), one 2" lg.
spacer (#2) and two 3/4" flange lock nuts (#14).
26518
25774
Pull Type Hitch Assembly
With Drawbar 13" & Higher
Figure 1-2
Pull Type Hitch Assembly
With Drawbar under 13" High
Figure 1-3
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
6. Return to the tractor, start engine and slowly operate
3-point controls to lift lower arms up just enough to
raise support stand (#3) off the ground.
7. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor.
8. Remove support stand (#3), turn it over and reattach
(Remember: Small notches in stand are mounted
towards the frame tube.)
9. Operate 3-point controls up and down to check for
clearance between the Seed Bed Roller and tractor.
Move or remove tractor drawbar if it interferes with
the Seed Bed Roller.
10. Manually adjust one of the two Lower lift arms up or
down to level the Seed Bed Roller from left to right.
Manually adjust the length of the top center link to
level the Seed Bed Roller from front to rear.
25764
Roller Scraper Assembly
Figure 1-4
11. When using a Quick Hitch, attach center hook to
1 1/4" spacer (#2) and lower hooks to hitch pins (#1).
3-Point Hook-Up
Refer to Figure 1-5 & Figure 1-6:
!
DANGER
allow anyone to stand between tractor and implement while
backing-up to an implement. Do not operate hydraulic 3-point
lift controls while someone is directly behind the tractor or
near the Seed Bed Roller.
Top Center Link
Hitch Hole
Crushing Hazard between tractor and implement. Do not
!
DANGER
Engage parking brake, shut off tractor and remove key before
dismounting from the tractor.
PTO Shaft
!
Lower Lift Arm
WARNING
Hitch Holes
See Figure 3-5 on page 15. Chock front and back of roller
when using support stand to prevent unit from rolling and
causing property damage and/or bodily injury.
23998
Tractor 3-Point Hitch
Figure 1-5
A 3-Point Category I hitch is required. The lower 3-Point
arms of the 3-Point hitch must be stabilized to prevent
side-to-side movement. Most tractors have sway blocks
or adjustable chains for this purpose.
Top Center Link Hole
Alignment Position
1. Slowly back tractor up to the Seed Bed Roller while
using the tractor’s 3-point hydraulic control to align
the lower lift arm hitch holes with the clevis lug holes
on the Seed Bed Roller.
2. Engage tractor park brake, shut tractor engine off
and remove key before dismounting from tractor.
3. With lower lift arm hitch holes aligned with clevis lug
holes, insert hitch pins (#1) through clevis and lower
arm holes. Secure hitch pins with linchpins (#6).
4. Align top center link hitch hole with the upper hitch
holes and insert 3/4" bolt (#4). Secure bolt with
flange lock nut (#5). Draw nut up snug.
Lower Lift Arm Hole
Alignment Positions
25781
Seed Bed Roller Hook-Up
Figure 1-6
5. Ensure lower hitch arms are blocked to prevent
excessive side movement.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 1: Assembly & Set-up
Clevis Hook-up
Refer to Figure 1-7 & Figure 1-8:
Pull-type Hook-up
1. Back machine up to the Seed Bed Roller until hole in
drawbar hitch is aligned with holes in the clevis hitch.
!
DANGER
Crushing Hazard between tractor and implement. Do not
allow anyone to stand between the tractor and implement
while backing-up to an implement.
2. Dismount machine properly and insert hitch pin (#3)
through hitch clevis holes and drawbar hitch hole.
Install hair pin cotter (#4).
3. Without removing wire snap lock pins (#5A & #5B):
!
DANGER
• Unhook wire retainers for both pins (#5A & #5B).
Engage parking brake, shut off tractor and remove key before
dismounting from the tractor.
• Rotate bottom of support stand (#1) back until hole
“A” is in alignment with wire snap lock pin (#5B).
• Push support stand onto both wire snap lock pins
and re-hook wire retainers.
!
WARNING
The Seed Bed Roller hitch has negative weight.
Ball Hook-up
Refer to Figure 1-9:
1. Attach customer supplied 2" ball (#8) to the machine
pulling the Seed Bed Roller. Tighten nut supplied
with the ball to correct torque. 2" Ball with 3/4" shank
(P/N 890-975C) can be purchased from Land Pride.
!
WARNING
See Figure 3-5 on page 15. Chock front and back of roller
when using support stand to prevent unit from rolling and
causing property damage and/or bodily injury.
2. Back machine up to the Seed Bed Roller until the 2"
ball is in alignment with ball socket in hitch (#2).
25799
25776
Clevis Hook-up (Tractor drawbar height under 13")
Figure 1-7
Ball Hook-up (Drawbar height 13" and higher)
Figure 1-9
3. Remove retaining pin (#3), pull up on lock latch
trigger (#6) and then pull up on release handle (#4).
4. With handle (#4) up, lower hitch (#2) over 2" ball (#8).
5. Make sure hitch (#2) is fully on ball (#8) and then
push handle (#4) down until lock latch (#6) is secured
in notch (#7).
6. Insert wire retaining pin (#3) in hole “A” and secure
pin in place with its wire retainer.
7. Without removing the two front wire snap lock
pins (#5A & #5B):
• Unhook wire retainers for both pins (#5A & #5B).
• Rotate bottom of support stand (#1) back until hole
25783
“A” is in alignment with wire snap lock pin (#5B).
• Push support stand onto both wire snap lock pins
Clevis Hook-up (Tractor drawbar height 13" and higher)
Figure 1-8
and re-hook wire retainers.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 2: Adjustments
Section 2: Adjustments
Scraper Bar Adjustment
Refer to Figure 2-1:
IMPORTANT: Scraper bar must be adjusted with
rear roller resting on the ground to ensure roller
rings are in their upper most position.
1. Slightly loosen hex nuts (#3) on both ends of the
scraper bar (#1). Nuts should be loose enough to
allow scraper bar movement but tight enough to hold
the scraper bar in place until nuts have been
retightened.
IMPORTANT: Tapping with a hammer may be
required to move scraper bar (#1). When doing so,
be sure to place a block of wood in the area to be
tapped. Tap hammer against the wood and not the
scraper bar to help protect the finish.
25784
Scraper Adjustment
Figure 2-1
2. Adjust scraper bar (#1) left or right to center scraper
teeth (#A) in the roller flutes and up or down until the
teeth just clear the bottom of the roller flutes. Some
light tapping with a hammer against a properly
placed block of wood may be required to move the
scraper bar.
3. Tighten 3/8"-16 nuts (#3) to the correct torque. Refer
Ball Hitch Swivel Adjustment
Refer to Figure 2-2:
IMPORTANT: Hex flange lock nut (#3) should be
adjusted tight enough so that the two mating plates
(#1 & #2) make contact but loose enough so that the
plates can rotate against each other.
A 16" long socket extension and 1 1/8" hex socket
will be required to reach the 3/4" hex flange nut (#3).
1. Hold plate (#1) from turning and tighten hex flange
nut (#3) until plate (#1) is against plate (#2).
2. Rotate ball hitch about plate (#2) by hand. If ball hitch
will not rotate, back nut (#3) off until it will rotate.
Insert Socket Extension
In This Opening
25785
Ball Hitch Swivel Adjustment
Figure 2-2
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Operating Procedures
Section 3: Operating Procedures
Make the following inspections if the Seed Bed
Roller is attached to a drawbar:
Operating Check List
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in the operation, transport,
1. Inspect safety equipment of the machine pulling the
Seed Bed Roller. Make sure the machine is in good
working condition.
maintenance and storage of the Seed Bed Roller.
Therefore, it is absolutely essential that no one operates
the roller without first having read, fully understood and
become totally familiar with the Operator’s Manual. Make
sure the operator has paid particular attention to:
2. Inspect levelness of tongue when setting-up. See
“Important Note” in box on page 8. Turn hitch
assembly over if needed by removing bolts (#10) and
bolts and pins with clips after turning hitch assembly
over. Be sure to tighten the nuts to the correct torque.
Transporting
!
CAUTION
When traveling on public roads at night or during the day, use
accessory lights and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
Operating Checklist
L Check
Referenc
Check 3-Point Hook-up procedure. Be sure all
pins have been installed and are secured.
1. The 3-Point Seed Bed Roller should be lifted as high
as possible to clear the ground when transporting.
Check Pull Type Hook-up procedure. Be sure
hitch pin or ball hitch is secured to the draw bar.
2. The frame and scrapers on the pull type Seed Bed
Roller are low to the ground while in transport
position. Be careful not to hit objects protruding from
the ground with the Seed Bed Roller.
Check optional rear scraper. Make sure it has
been adjusted and all bolts are tight.
Check ball hitch swivel. Make sure the swivel
nut is properly tightened.
3. Leave enough clearance on both sides of the Seed
Bed Roller when traveling straight and when making
turns to keep the unit from contacting obstacles such
as buildings, trees and fences. Always reduce
ground speed when turning.
Make sure the operator has read and knows
how to operate the Seed Bed Roller.
Make sure the Seed Bed Roller has been
lubricated as required.
Check Seed Bed Roller initially and periodically
for loose bolts & pins, Tighten bolts to the
correct torque.
4. Select a safe ground travel speed when transporting
from one area to another. Do not travel over 10 MPH
while carrying the Seed Bed Roller on its wheels.
5. Always travel on roadways in such a way that faster
moving vehicles may pass you safely.
Make the following inspections if the Seed Bed
Roller is attached to a 3-Point lift:
6. Slow down when traveling over rough or hilly terrain.
7. Never back-up with the Seed Bed Roller down.
1. Inspect tractor safety equipment. Make sure the
tractor is in good working condition.
8. Be aware of negative hitch weight on the pull type
Seed Bed Roller when in transporting. Negative hitch
weight can cause loss of vehicle control. Add weight
to the rear of the vehicle if needed.
2. Carefully raise and lower the implement to ensure
that the tractor drawbar, tires, and other equipment
on the tractor do not contact the frame and roller.
3. Make sure the lower 3-Point arms are stabilized to
prevent side-to-side movement. Most tractors have
sway blocks or adjustable chains for this purpose.
9. Do not transport on a public roads with roller down.
Damage to unit and/or road may occur.
4. Check tractor ballast. Ballast may need to be added
to your tractor to maintain steering control. Refer to
your tractor Operators Manual to determine whether
or not to add ballast.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 3: Operating Procedures
Operating Instructions
!
CAUTION
2. With the roller on the ground, travel straight forward
at a safe speed of 3 to 5 MPH. Allow room to make
wide turns or lift the unit out of the ground to make
sharp turns. Make wide turns when:
Be careful when lowering the pull type roller to ground. Make
sure no one is under, behind or near the unit when lowering.
The roller is very heavy and can crush someone. The hitch can
also flip over suddenly and hit someone.
• 3-Point Type: Always raise the Seed Bed Roller off
the ground before turning around at the end of a run
and when making sharp corners.
!
CAUTION
• Pull-Type: Make sure the tires on the machine
pulling the Seed Bed Roller do not make contact
with the tongue and if attached, drag harrow chain.
Do not use the Seed Bed Roller to pull or push fence post,
stumps or any other object.
3. Do not operate in reverse (traveling backwards) with
the roller on the ground. The Seed Bed Roller is
designed for working soil while traveling forward only.
Damage to the frame may occur.
!
DANGER
Do not carry a rider on the Seed Bed Roller. Riders can get
hurt while being carried or fall and be crushed by the roller.
4. It is best to cross ditches straight on, to make full
roller contact with the soil.
IMPORTANT: Damage to the 3-Point Seed Bed
Roller can occur if the unit is not raised off of the
ground before making sharp turns.
o
Rotate Hitch 180 Over
Roller Body To Change
to Field Set-Up.
IMPORTANT: Damage to pull type Seed Bed Roller
can occur to tongue and machine pulling the unit if
too sharp a turn is made.
!
CAUTION
Be aware of negative hitch weight when unhooking the Seed
Bed Roller while in transport position. The hitch can suddenly
swing up.
IMPORTANT: Beware of negative
25782
hitch weight when unhooking.
Pull-Type Set-Up (Transport Set-Up Shown)
Figure 3-1
!
CAUTION
Be aware of positive hitch weight when unhooking the Seed
Bed Roller while in field position. The hitch can suddenly drop
while unhooking the unit.
o
Rotate Hitch 180 Over
Roller Body To Change to
Transport Set-Up
1. Lower Seed Bed Roller to the ground as follows:
3-Point Type:
a. Lower roller to the ground using the tractor’s
3-Point lift controls. Make any required final
adjustments to the 3-Point lower arms and center
link as outlined in step 10 on page 9.
Pull-Type:
a. Transport Position to Field Position:
Lower roller to ground by unhooking from the
pulling machine and lifting up and rotating the
IMPORTANT: Beware of positive
hitch weight when unhooking.
25762
o
Pull-Type Set-Up (Field Set-Up Shown)
Figure 3-2
hitch 180 up over the roller body as shown in
Figure 3-1. Re-hook hitch to the drawbar. If using
o
ball hitch, rotate ball hitch 180 to re-hookup.
b. Field Position to Transport Position:
Raise roller for transporting by unhooking from
the pulling machine, lifting up and rotating the
o
hitch 180 up over the roller body as shown in
Figure 3-2. Re-hook hitch to the machine. If using
o
ball hitch, rotate ball hitch 180 to re-hookup.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 3: Operating Procedures
Unhooking the Seed Bed Roller
!
CAUTION
Be careful when lowering the pull type roller to ground. Make
sure no one is under, behind or near the unit when lowering.
The roller is very heavy and can crush someone. The hitch can
also flip over suddenly and hit someone.
!
DANGER
Always engage parking brake, shut off tractor and remove key
before dismounting from tractor.
3-Point Type
position.
4. Store Seed Bed Roller in a clean, dry place.
Pull-Type Units
There are three methods of storing pull-type units:
2. Lower Seed Bed Roller onto a level solid surface.
The roller may start rolling while unhooking if not on
level ground.
• Position unit on a flat level surface. Raise pull hitch
up until unit is resting on its rear wheels and
supports or posts if necessary to prevent the
possibility of the unit tipping over. Chock front and
back of wheels.
3. Shut tractor engine off and engage parking brake.
4. Ensure that the unit is stable. Chock front and back of
rear roller if needed especially if unit is not on level
ground.
• Position unit on a flat level surface. Raise pull hitch
up until the unit is resting on its rear roller and
stable. Use auxiliary supports or posts if necessary
to prevent the possibility of the unit tipping over.
Chock front and back of roller.
5. Disconnect top center link from the Seed Bed Roller.
6. Disconnect the lower 3-Point lift arms from the Seed
Bed Roller.
Pull Type
• Do not leave unit resting on its wheels (transport
position) and hitch support. The hitch can develop
negative weight and swing up on its own. Instead,
position unit on a flat level surface. Rotate hitch up
!
WARNING
Chock front and back of roller when using support stand to
prevent unit from rolling and causing property damage and/or
bodily injury.
o
and over 180 until unit is resting on the hitch
support and rear roller as shown in Figure 3-5.
Ensure unit is stable by chocking the front and back
of roller.
1. Park on a level solid surface. The roller may start
rolling while unhooking if not on level ground.
3-Point Lift Units
2. Shut vehicle engine off and engage parking brake.
• Position unit on a flat level surface. Lower 3-Point
hitch until the rear roller and support stand are
resting on the ground. Ensure that the unit is stable.
Chock rear roller if needed especially if unit is not on
level ground.
3. Ensure that the unit is stable. Chock front and back of
rear roller to prevent unit from rolling.
4. Disconnect clevis hitch or ball hitch from machine
towing the Seed Bed Roller.
o
5. If in transport, rotate hitch 180 over the roller body to
5. Repaint where paint is worn or scratched to prevent
rust. Ask your dealer for Land Pride touch-up paint.
rest unit on the rollers and not on the wheels.
6. Set support stand in park position. (See Figure 3-5
on page 15.)
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
positions to store pull type unit.
821-011C
821-002C
821-054C
821-058C
821-066C
821-067C
PAINT LP BEIGE AEROSOL SPRAY CAN
PAINT LP BLACK AEROSOL SPRAY CAN
PAINT MEDIUM RED AEROSOL SPRAY CAN
PAINT GREEN AEROSOL SPRAY CAN
PAINT ORANGE AEROSOL SPRAY CAN
PAINT BLUE AEROSOL SPRAY CAN
Storage Instructions
Clean Seed Bed Roller at the end of the working season
or when the roller will not be used for a long period.
1. Clean off any dirt or grease that may have
accumulated on the roller and moving parts. Scrape
off compacted dirt and then wash the surface
thoroughly with a garden hose.
2. Inspect for loose, damaged or worn parts and adjust
or replace as needed.
3. Lubricate as noted in the Lubrication portion of this
section starting on page 16.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 3: Operating Procedures
25798
General Operating Instructions
!
WARNING
Do not use the roller for pulling fence posts, stumps, etc.,
lifting objects, carry objects or towing other equipment. Any
of the above can result in roller damage, serious bodily injury
or death.
!
DANGER
Never carry a person on the roller. A person can fall and be
ran over by the roller or tractor causing serious injury or
death.
By now you should have read the operator’s manual and
familiarized yourself with all of the possible applications
and mounting instructions for your Land Pride Seed Bed
Roller. You should now also be familiar with
Chock Front & Back of Wheels
Stored Supported on Rear
Wheels & Scraper
recommended safety and maintenance procedures. It’s
time to put your new Seed Bed Roller to work. Whether
you have a three-point hitch mounted model or a pull-
type, it will be important to maintain a ground speed
below 7 miles per hour. Driving faster than 7 mph can
result in causing your roller to bounce and not deliver the
surface finish and seed to soil contact required for
maximum germination. It is also best to avoid sharp turns
if you want to maintain a uniform finish. The soil should
have a very dry texture to it when rolling seed into firmer
contact with the soil. Wet or sticky soil will build up on the
roller only to be scraped off and deposited on the surface
in non-uniform clumps by the roller scrapers. If you are
rolling to press seed down in an Overseeding application
on pasture or turf grass, it is also important to wait till the
grass is dry to avoid accumulations of seed build up
sticking to the roller.
Storage Positions For Tight Areas
Figure 3-3
25798
Chock Back
of Roller
If you are transporting a pull-type Seed Bed Roller from
one location to another, it is important to remember that
the 10" transport wheels are for low speed use and
therefore a 10 mph top transport speed should not be
exceeded. It is also important to note that in the transport
mode you have approximately 5" of ground clearance so
take care not to drive over larger rocks, debris, and
protruding tree roots. Never pull onto hard surfaces or
paved areas with the roller on the ground or excessive
wear and damage may occur. The Land Pride Seed Bed
Roller is a very user friendly attachment and with a little
practice you should begin to achieve professional results
in no time at all. See Specifications and Feature Benefits
Stored Supported on Rear
Roller & Scraper
Storage Positions For Tighter Areas
Figure 3-4
25798
Chock Front & Back of Roller
Stored Supported on the Roller & Support Stand
Storage Position Using Support Stand
Figure 3-5
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Maintenance & Lubrication
Section 4: Maintenance & Lubrication
Maintenance
After using your Seed Bed Roller for several hours,
check all bolts to be sure they are tight. Loose bolts can
damage the unit and/or hurt someone especially if the
roller falls from the support frame.
!
CAUTION
Do not work on or around the Seed Bed Roller without
blocking the unit properly. The roller raised off the ground
could drop suddenly crushing someone. If the roller is on the
ground, it could roll onto someone crushing that person.
Always use genuine Land Pride replacement parts. Any
Land Pride equipment that has been altered or modified
without Land Pride’s specific recommendation, approval
and authorization in writing excludes the warranty.
Proper servicing and adjustment is the key to the long life
of any implement. With careful and systematic
inspection, you can avoid costly maintenance, time and
repair.
Replace any worn, damaged or illegible safety labels by
obtaining new labels from your Land Pride Dealer.
Lubrication
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
50
hrs
Intervals in hours at which
lubrication is required
8
Hours
Roller Flange Bearings
Number of Zerks: 2
Type of Lubrication: Multi-purpose Grease
Quantity = 2 pumps
25796
8
Hours
Wheel Bearings
Number of Zerks: 2
Type of Lubrication: Multi-purpose Grease
Quantity = 2 pumps
25797
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
16
Land Pride
Section 5: Additional Equipment
Section 5: Additional Equipment
Additional Seeding Equipment
Disc Harrow
Refer to Figure 5-1:
Land Pride Disc Harrows are designed to open and
break up soil surface in preparation for planting.
Land Pride Disc Harrow Models
Model DH1048 & DH1060. . . . . . . . . . . 48" & 60" Wide
Model DH1560 & DH1572 . . . . . . . . . . .60" & 72" wide
Model DH2572 & DH2584 . . . . . . . . . . .72" & 84" wide
Additional equipment can be attached behind the Disc
Harrow to make it a complete seeding package. See
Spin Spreader
Mounting Bracket
Rear Hitch
25609
Electric Spin Spreader, Mounting Bracket & Rear Hitch
Figure 5-2
Drag Harrow
Refer to Figure 5-3:
The Land Pride Drag Harrows are designed for various
types of seedbed and ground preparations. They can be
used to smooth out freshly cultivated soil, work seed and
fertilizer into freshly cultivated soil or into turf and pasture
grass, fluff and level arenas, aerate soil for faster
dry-down time, de-thatch and aerate lawns and pastures,
break up aeration cores on turf surfaces and groom
snow-packed ski resorts.
17800
Disc Harrow Assembly (DH Series)
Figure 5-1
The Drag Harrow can also be used in tandem with Land
Pride’s Disc Harrow, Electric Spin Spreader and Seed
Bed Roller to provide a highly efficient and complete
seeding application in one pass. See “Complete One
Electric Spin Spreader
Refer to Figure 5-2:
The Land Pride Electric Spin Spreader is a highly
versatile package designed to plant or spread seeds,
fertilizer, lime, gypsum, and other soil conditioning
amendments at distances ranging from 4 ft. to 20 ft. It
can also be used in the off-season to spread sand or salt
for winter icing or slick snow conditions.
Land Pride Drag Harrow Models
Model DRG04 . . . . . . . . . . . . . . . . 4 ft. wide x 4 ft. long
Model DRG06 . . . . . . . . . . . . . . . . 6 ft. wide x 4 ft. long
Model DRG08 . . . . . . . . . . . . . . . . 8 ft. wide x 4 ft. long
The unit has a 12 Volt remote tether control that can be
operated right from the driver seat to turn the spreader on
or off or to set the seed-gate opening to different
application rates.
The Spin Spreader has applications in overseeding of
pastures, grassy runways, open areas, roadsides,
medians, wild game food plots, hunting clubs, hunting
resorts, ranches, farms, game preserves, landscaping,
and hobby farming. It also works very well in gardens and
nurseries to incorporate fertilizer and pelletized gypsum
or lime as soil amendments.
Accessories are available for mounting the spreader to a
2" receiver hitch on a utility vehicle or to a Land Pride
Disc Harrow. A rear hitch can be attached to the Disc
Harrow Spin Spreader mounting bracket. The Drag
Harrow and Seed Bed Roller can then be hitched to the
rear hitch. See “Complete One Pass Seeding
25611
Drag Harrow (6’ x 4" Shown)
Figure 5-3
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 5: Additional Equipment
Complete One Pass Seeding Application
Refer to Figure 5-4:
Land Pride offers a Seeder/Overseeder component
system for one-pass ground cultivation and seed to soil
integration for applications on previously tilled soil,
existing pasture ground, large grassy areas, reclamation
sites and wild game food plots. This system is comprised
of a Land Pride Disc Harrow, rear mounted Electric Spin
Spreader with special hitch kit, trailing Drag Harrow, and
trailing Pull-type Seed Bed Roller.
See your nearest Land Pride Dealer for more information
25802
Complete One Pass Seeding Application
Figure 5-4
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
18
Land Pride
Section 6: Specifications & Capacities
Section 6: Specifications & Capacities
SBR Series
Description
Three-Point
SBR60
372 lbs.
800 lbs.
60"
Pull-Type
SBR60
SBR48
320 lbs.
700 lbs.
48"
SBR72
442 lbs.
900 lbs.
72"
SBR48
360 lbs.
450 lbs.
48"
SBR72
478 lbs.
600 lbs.
72"
Unit Weight
412 lbs.
Minimum Required Tractor Weight
Working Width
550 lbs.
60"
Overall Width
53"
65"
77"
60"
72"
84"
Overall Length
18"
77"
Overall Height
30 3/4"
18.9"
Roller Diameter
11 3/8"
11 3/8"
Roller Material Construction
Hitch Type
Notched Gray Iron
Notched Gray Iron
Cat. 1 and Cat. 1 QH Compatible
Pull-type Clevis and
Indexing 2" Ball Combination
18-50 hp.
Tractor HP Requirement
Roller Scrapers
18-50 hp.
Standard Equipment
N/A
Standard Equipment
Transport Wheels
Two 10" x 3 1/4" Solid Rubber
Straight Ribbed Tread
Hitch Support Stand
Standard Equipment
Standard Equipment
18"
77 3/4"
26791
26790
Three Point Type
Pull Type
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
19
Section 7: Features and Benefits
Section 7: Features and Benefits
SBR Series
Features
Benefits
Category 1 Three-point hitch or Pull-type
Configurations.
Matches customers operational and equipment needs.
Three point hitch model is Cat. 1 Quick Hitch
compatible.
Makes for faster and easier hook-up to the tractor.
Standard equipment support stands for both
three-point hitch and pull-type models.
Keeps the hitches up and out of the dirt and ready for easy hook-up.
Optional Pull-type Hitch assembly bolts on and
converts the Three-point model to a Pull-type
model.
Provides low cost dual hitch capability for added value and operational
versatility.
Indexing dual capability hitch on Pull-type
configuration.
Insures easy fit and function for 2" ball or pin and clevis type attachment.
Low maintenance indexing flip-over hitch on
pull-type configuration.
Allows operator’s to switch from transport to working position and back
again with ease and keeps costs down.
Notched and ribbed patterned gray iron roller.
Provides for optimal seedbed finish and long durable product life.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
20
Land Pride
Section 8: Appendix
Section 8: Appendix
Torque Values Chart For Common Bolt Size
Bolt He a d Id e ntific a tion
Bolt He a d Id e ntific a tion
8.8
10.9
5.8
Bolt Size
(Inc he s)
Bolt Size
(Me tric )
Class 5.8
Class 8.8
Class 10.9
Grade 2
Grade 5
3
Grade 8
1
in-tpi
N · m ft-lb N · m ft-lb N · m ft-lb
mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb
1/4" - 20
7.4
8.5
15
5.6
11
8
16
12
M 5 X 0.8
4
3
6
5
9
7
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
6
13
10
18
14
M 6 X 1
7
5
11
8
15
11
11
24
17
33
25
M 8 X 1.25
M 8 X 1
17
12
26
19
36
27
17
13
26
19
37
27
18
13
28
21
39
29
27
20
42
31
59
44
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
33
24
52
39
72
53
31
22
47
35
67
49
39
29
61
45
85
62
43
32
67
49
95
70
58
42
91
67
125
130
145
200
l215
315
335
405
485
610
900
93
49
36
75
55
105
145
165
210
235
285
325
510
570
820
905
78
60
44
95
70
97
66
49
105
115
150
165
205
230
360
405
585
640
875
955
76
105
120
155
170
210
240
375
420
605
670
90
66
105
145
155
225
240
310
350
440
650
760
830
77
105
150
160
230
245
300
355
450
665
75
55
85
M14 X 2
92
68
105
115
165
180
230
260
325
480
560
610
95
70
110
120
150
170
265
295
430
475
645
705
M14 X 1.5
M16 X 2
99
73
105
130
150
235
260
225
250
340
370
480
540
680
750
890
79
145
155
195
220
280
310
480
525
960
105
115
145
165
205
230
355
390
705
97
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
110
170
190
165
185
250
275
355
395
500
555
655
7/8" - 14
1" - 8
1050 780
1150 845
1230 910
1350 995
1750 1290
1960 1440
M24 X 2
1" - 12
M30 X 3.5
M30 X 2
1510 1120 2100 1550
1680 1240 2320 1710
1-1/8" - 7
1 1/8" - 12
1 1/4" - 7
1 1/4" - 12
1 3/8" - 6
1 3/8" - 12
1 1/2" - 6
1 1/2" - 12
1080 795
1210 890
1060 785
M36 X 3.5
1730 1270 2650 1950 3660 2700
1880 1380 2960 2190 4100 3220
1520 1120 2460 1820
1680 1240 2730 2010
1990 1470 3230 2380
2270 1670 3680 2710
2640 1950 4290 3160
2970 2190 4820 3560
M36 X 2
1
in-tpi = nominal thread diameter in inches-threads per inch
N· m = newton-meters
2
3
4
1010 745
1180 870
1330 980
ft-lb= foot pounds
mm x pitch = nominal thread diameter in millimeters x thread
pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Additional Torque Values
Wheel Spindle Nut
(3/4"-10 Lock Nut)
Tighten lock nut until tire does not rotate easily and then back-off nut until tire turns
freely.
Ball Hitch Swivel Nut
(3/4"-10 Hex Flange Top Lock Nut)
make contact but loose enough so that the mating plates can rotate against each other.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
2/23/09
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 8: Appendix
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
This Warranty is limited to the replacement of any defective part by Land
Pride and the installation by the dealer of any such replacement part, and does
not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials
or design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in
this written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days
from the date of purchase by the end user.
Model SBR48, SBR60 & SBR72 Seed Bed Roller 322-215M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/23/09
23
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|