Shredder Kit
For RC(M)5515 & RC(M)6515 Rotary Cutters
Manual No. 330-094M
Before You Start
Further Assistance
Your dealer wants you to be satisfied with your new
Shredder Kit. If for any reason you do not understand any
part of this manual or are not satisfied with the service
received, the following actions are suggested:
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
Your Shredder Kit is exclusively designed for your Land
Pride 55 and 65 Series Rotary Cutter. Please read these
installation instructions and your Rotary Cutter
Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
A separate Rotary Cutter Parts Manual is available free
from your nearest Land Pride dealer. Have the model
and serial numbers of your cutter handy when placing an
order.
Safety Information
!
WARNING
Never work under equipment supported by hydraulics.
Hydraulics can drop equipment if controls are actuated or if
hydraulic lines burst. Either situation can drop the cutter
instantly even when power to the hydraulics is shut off.
Manual Part Numbers:
• Operator’s Manual . . . . . . . . . . . . . . . . . 318-721M
• Parts Manual . . . . . . . . . . . . . . . . . . . . . 318-721P
General Information
!
DANGER
These assembly instructions apply to the Shredder Kit
listed below:
Always disconnect main driveline from tractor PTO before
servicing the cutter deck. Cutter can be engaged if tractor is
started resulting in damage to the cutter, bodily injury and/or
death.
330-094A RC(M)5515 & RC(M)6515 SHREDDER KIT
NOTE: Land Pride recommends safety glasses and
work gloves be worn while working on the Rotary
Cutter.
Shredder Assembly Instructions
A detailed listing of parts for this accessory kit is provided
on page 4. Use the list as a checklist to inventory parts
received. Please contact your local Land Pride dealer for
any missing hardware.
IMPORTANT: Read “Safety Information” above
before installing the shredder blades.
Refer to Figure 2 on page 2:
1. Remove all three existing blade carrier assemblies
from the gearbox output shafts. Keep flat washers
(D), slotted hex nuts (E) and cotter pins (F) for reuse.
© Copyright 2007
Printed
8/20/07
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Land Pride
Shredder Assembly Instructions
1.
2.
Replacing Blade Spacers
Refer to Figure 4:
The cutting blades should not have more than 3/4" free
vertical movement at the blade tips. If vertical movement
exceeds 3/4", install or change to thicker spacers (#1)
following steps 1-5.
Check blade deflection. If vertical deflection at the
blade tip is greater than 3/4", remove blade bolt (#4)
and reassemble using a thicker spacer (#1). Select
spacer thickness based on deflection. The greater
the deflection, the thicker the spacer.
Assemble blades by inserting 1"-8 x 4 1/2" GR8 hex
head bolt (#4) through blade bushing (#2),
spacer (#1), lower cutting blade (#6, #7 or #8), blade
carrier (#3), upper flat cutting blade (#10 or #9),
spacer (#1) and blade bushings (#2). Temporarily
secure blade with a plain hex nut (Plain hex nut
furnished by customer.) Draw nut up snug. Do not
tighten.
Order spacers (#1) and locknuts (#8) from your nearest
Land Pride Dealer.
IMPORTANT: Read “Safety Information” on page 1
before disassembling the shredder blades.
3.
4.
IMPORTANT: Locknuts can lose their ability to lock
properly once removed. Always use a plain throw
away nut during pre-assembly of spacers.
Check blade vertical movement. If movement at the
blade tip is greater than 3/4", remove blade bolt and
reassemble as before except use a thicker spacer.
Once blade deflection is correct, replace plain nut
with supplied locknut (#5) & torque to 450 ft-lbs.
5. Repeat instructions for “Replacing Blade Spacers”
for the remaining shredder blade assemblies.
IMPORTANT: Spacers (#1) are not used if vertical
movement at the blade tip is 3/4" or less without
spacers. However, spacers are required if vertical
movement at the blade tips are greater than 3/4".
Position Beveled
Edges Down
Blade
Cutting
Edges
(#3) Left Wing Shredder Assembly
Clockwise Rotation
(#1) Right Wing Shredder Assembly
Counterclockwise Rotation
Lower Blade Cutting Edges
Position Beveled Edges Up
(#2) Center Deck & Shredder Assemblies
Counterclockwise Rotation
25603
Figure 4
8/20/07
■
Manual No. 330-094M
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Listing of Parts
Kit No. 330-094A
RC(M)5515 & RC(M)6515 SHREDDER ASSEMBLY
Item Qty. Part No. Part Description
1
1
1
1
330-094M
330-091S
330-092S
330-093S
SHREDDER KIT INSTALLATION MANUAL
1
2
3
CCW BLADES, SHREDDER 60" . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 1 on page 2)
CCW BLADES, SHREDDER 72" . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 2 on page 2)
CW BLADES, SHREDDER 60" . . . . . . . . . . . . . . . . . . . . . . . . . . . . (See Figure 3 on page 2)
Refer to Figure 4 on page 3:
(#1) Components for 330-091S CCW Blade Assembly (Left Wing Shredder - 60" cut)
1
1
1
1
2
3
4
5
7
4
4
4
4
4
1
2
2
2
4
312-075D
312-082D
312-089D
312-808D
318-309D
330-090H
802-680C
803-168C
820-169C
820-217C
BLADE SPACER 16 GA
BLADE SPACER 18 GA
BLADE SPACER 20 GA.
BLADE SPACER 24GA
BLADE BUSHING
BLADE BAR, SHREDDER 5515
HHCS 1-8 X 4 1/2 PLT GR8
NUT HEX TOP LOCK 1-8 PLT
A maximum of four spacers
are used per assembly.
CUTTER BLADE 1/2X4X23 CCW
CUTTER BLADE 1/2X4X22.5 FLAT
10
Refer to Figure 4 on page 3:
(#2) Components for 330-092S CCW Blade Assembly (Center Deck Shredder - 72" cut)
1
1
1
1
2
3
4
5
6
9
4
4
4
4
4
1
2
2
2
2
312-075D
312-082D
312-089D
312-808D
318-309D
330-090H
802-680C
803-168C
820-168C
820-216C
BLADE SPACER 16 GA
BLADE SPACER 18 GA
BLADE SPACER 20 GA.
BLADE SPACER 24GA
BLADE BUSHING
BLADE BAR, SHREDDER 5515
HHCS 1-8 X 4 1/2 PLT GR8
NUT HEX TOP LOCK 1-8 PLT
A maximum of four spacers
are used per assembly.
CUTTER BLADE 1/2X4X29 CCW
CUTTER BLADE 1/2X4X28.5 FLAT
Refer to Figure 4 on page 3:
(#3) Components for 330-093S CW Blade Assembly (Right Wing Shredder - 60" cut)
1
1
1
1
2
3
4
5
8
4
4
4
4
4
1
2
2
2
4
312-075D
312-082D
312-089D
312-808D
318-309D
330-090H
802-680C
803-168C
820-170C
820-217C
BLADE SPACER 16 GA
BLADE SPACER 18 GA
BLADE SPACER 20 GA.
BLADE SPACER 24GA
A maximum of four spacers
are used per assembly.
BLADE BUSHING
BLADE BAR, SHREDDER 5515
HHCS 1-8 X 4 1/2 PLT GR8
NUT HEX TOP LOCK 1-8 PLT
CUTTER BLADE 1/2X4X23 CW
10
CUTTER BLADE 1/2X4X22.5 FLAT
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Manual No. 330-094M
Download from Www.Somanuals.com. All Manuals Search And Download.
■
8/20/07
4
|