TX7U Outdoor Temperature/Humidity Sensor
The TX7U outdoor temperature/humidity sensor can be added to your existing
units in operation. The outdoor temperature/humidity sensor measures the
outdoor temperature and humidity (or any other location you wish to know the
temperature and humidity) and transmits the data to the indoor display station.
Outdoor
temperature/humidity
sensor
Mounting Bracket
INVENTORY OF CONTENTS
1. Outdoor temperature/humidity sensor.
2. Mounting bracket.
3. Rain protector.
4. Two each, ½” Philips mounting screws.
5. One strip double sided adhesive tape.
6. Instruction manual and warranty return card.
ADDITIONAL EQUIPMENT (not included)
1. One Philips screwdriver.
2. One Flat screwdriver.
3. Two fresh AA 1.5V batteries.
I. SETTING UP
Before you begin, assign a number to each outdoor temperature/humidity sensor
(i.e. #1 for outdoors, #2 for the basement, etc.) if you have multiple sensors. This
will help you determine which temperature, from which outdoor
temperature/humidity sensor, you are reading on the indoor display station.
Note: Remove batteries from all existing units in operation—including outdoor
temperature/humidity sensor units and indoor display stations. When setting up
multiple units it is important to insert batteries first into all the outdoor
temperature/humidity sensors, and in numeric sequence. Second install batteries
into the indoor display station. Transmission problems will arise if this is not done
correctly and if the total time for setup exceeds 6 minutes.
A. BATTERY INSTALLATION
Follow these directions when first setting up, when replacing batteries,
or for resetting purposes.
1. Remove the batteries from all existing display units in operation.
2. Using a screwdriver, unscrew and open the battery cover located
at the front of the outdoor temperature/humidity sensor.
Battery
Battery cover
compartment
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Snap the outdoor temperature/humidity sensor into
place on the mounting bracket.
B. MOUNTING WITH ADHESIVE TAPE
1. With a nonabrasive solution, clean and dry the back of
the mounting bracket and the mounting surface to
ensure a secure hold. The mounting surface should be
smooth and flat.
2. Remove the protective strip from one side of the tape.
Press firmly into the designated area on the back of the
mounting bracket.
3. Remove the protective strip from the other side of the
tape, and position the outdoor temperature/humidity
sensor in the desired location.
C. MOUNTING USING THE BRACKET AS A STAND
The mounting bracket can be used as a stand by simply attaching
the bracket to the bottom of the temperature/humidity sensor.
Once snapped in place the sensor can then be placed on a shelf,
table or other surface where the temperature and humidity
measurements are desired.
III. MAINTENANCE AND CARE
1. Extreme temperatures, vibrations, and shock should be avoided to
prevent damage to the units
2. Clean displays and units with a soft, damp cloth. Do not use solvents
or scouring agents, they may mark the displays and casings
3. Do not submerge in water.
4. Do not subject the units to unnecessary heat or cold by placing them in
the oven or freezer.
5. Opening the casings invalidates the warranty. Do not try to repair the
unit. Contact La Crosse Technology for repairs.
IV. SPECIFICATIONS
-21.8ºF to 157.8ºF with 0.2ºF
Temperature measuring
resolution
range
(-29.9°C to 69.9°C)
Relative Humidity
measuring range
1% to 99% with 1%
resolution)
Every 10 seconds in first 3
minutes
Transmission interval
Every 1 minute thereafter
Transmission frequency
Power source
433.92 MHz
2 x 1.5V AA Battery
Alkaline recommended
6.3” x 2.95” x 2.2”
(160 x 75 x 55mm)
Dimensions (H x W x D)
Download from Www.Somanuals.com. All Manuals Search And Download.
V. LIABILITY DISCLAIMER
1. The manufacturer and supplier cannot accept any responsibility for any
incorrect readings and any consequences occurring should an
inaccurate reading take place.
2. This product is not to be used for medical purposes or for public
information.
3. The specifications of this product may change without prior notice
4. This product is not a toy. Keep out of children’s reach.
5. No part of this manual may be reproduced without written consent of
the manufacturer.
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original purchaser
of this product. To receive warranty service, the purchaser must contact La
Crosse Technology, Ltd for problem determination and service procedures.
Warranty service can only be performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to La Crosse Technology, Ltd or La Crosse
Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at
no charge as stipulated herein, with new or reconditioned parts or products if
found to be defective during the limited warranty period specified above. All
replaced parts and products become the property of La Crosse Technology, Ltd
and must be returned to La Crosse Technology, Ltd. Replacement parts and
products assume the remaining original warranty, or ninety (90) days, whichever
is longer. La Crosse Technology, Ltd will pay all expenses for labor and
materials for all repairs covered by this warranty. If necessary repairs are not
covered by this warranty, or if a product is examined which is not in need or
repair, you will be charged for the repairs or examination. The owner must pay
any shipping charges incurred in getting your La Crosse Technology, Ltd product
to a La Crosse Technology, Ltd authorized service center. La Crosse
Technology, Ltd will pay ground return shipping charges to the owner of the
product to a USA address only.
Your La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must be
presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions
contained in your owner’s manual; (5) damage resulting from the performance of
repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home
use (7) applications and uses that this product was not intended or (8) the
products inability to receive a signal due to any source of interference. This
warranty covers only actual defects within the product itself, and does not cover
the cost of installation or removal from a fixed installation, normal set-up or
adjustments, claims based on misrepresentation by the seller or performance
variations resulting from installation-related circumstances.
Download from Www.Somanuals.com. All Manuals Search And Download.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS
PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL
PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A
TOY. KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights
specific to your State. Some States do no allow the exclusion of consequential or
incidental damages therefore the above exclusion of limitation may not apply to
you.
For warranty work, technical support, or information contact:
La Crosse Technology
2809 Losey Blvd. S.
La Crosse, WI 54601
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
FCC DISCLAIMER
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We
accept no liability for technical mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
Download from Www.Somanuals.com. All Manuals Search And Download.
|