La Crosse Technology Portable Radio WS 7076U User Manual

WS-7076U  
Wireless 433 MHz  
Radio-controlled Weather Station  
Instruction Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INVENTORY OF CONTENTS  
1. The weather station (Figure 1).  
2. One TX6U remote temperature sensor with mounting bracket  
(Figure 2).  
3. Three each, ½” Philips screws.  
4. One strip double-sided adhesive tape.  
5. Instruction Manual and Warranty Card.  
Figure 2  
Time LCD  
Date LCD  
Indoor LCD  
Mounting  
Bracket  
Outdoor LCD  
Figure 1  
ADDITIONAL EQUIPMENT (not included)  
1. Two, fresh AA 1.5V batteries for indoor weather station.  
2. Two, fresh AA 1.5V batteries for remoter temperature sensor.  
3. One, Philips screwdriver for mounting.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ABOUT WWVB (Radio Controlled Time)  
The NIST (National Institute of Standards and Technology—Time and Frequency  
Division) WWVB radio station is located in Ft. Collins, Colorado and transmits the  
exact time signal continuously throughout the United States at 60 kHz. The signal  
can be received up to 2, 000 miles away through the internal antenna in the weather  
station. However, due to the nature of the earth’s ionosphere, reception is very  
limited during daylight hours. The weather station will search for a signal every  
night when reception is best. The WWVB radio station derives its signal from the  
NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is  
continually measuring every second, of every day, to an accuracy of ten billionths of  
a second per day. These physicists have created an international standard measuring  
a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.  
For more information on WWVB and the atomic clock please see the NIST website  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUICK SET-UP GUIDE  
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.  
1. Have the indoor weather station and remote temperature sensor 3 to 5  
apart.  
2. Batteries should be out of both units.  
3. Place the batteries into the remote temperature sensor first then into  
the indoor weather station.  
(All remote temperature sensors must be started before the indoor  
weather station)  
4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.  
In this time the indoor weather station and remote temperature sensor will start to  
talk to each other and the indoor weather station will show both the indoor  
temperature and an outdoor temperature. If the indoor weather station does not  
display both temperatures after the 15 minutes please retry the set up as stated above.  
After both indoor and outdoor temperatures are displayed for 15 minutes you can  
place your remote temperature sensor outdoors and set your time.  
The remote temperature sensor should be placed in a dry, shaded area. The remote  
temperature sensor has a range of 80 feet. Any walls that the signal will have to pass  
through will reduce distance. An outdoor wall or window can have up to 30 feet of  
resistance and an interior wall can have up to 20 feet of resistance depending upon  
the type of construction. Your distance plus resistance should not exceed 80 ft. in a  
straight line.  
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain  
must be avoided.  
To complete the set up of your indoor weather station after the 10 minutes have  
passed please follow the steps on pages 8 and 9.  
Note: The remote temperature sensor transmits a signal every 3 minutes;  
after the batteries have been installed, the indoor weather station will  
search for the signal for a duration of 5 minutes. If there is no temperature  
reading in the OUTDOOR LCD after 5 minutes, make sure the units are  
within range of each other or repeat the battery installation procedure.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
DETAILED SET-UP GUIDE  
I. BATTERY INSTALLATION  
A. REMOTE TEMPERATURE SENSOR  
1. Remove the mounting bracket. The  
bracket snaps on and off easily.  
2. Remove the battery cover, by sliding the  
cover down.  
3. Observing the correct polarity install 2  
AA batteries. The batteries will fit  
tightly (to avoid start-up problems make  
sure they do not spring free).  
4. Replace the battery cover by sliding  
upwards. Be sure battery cover is on  
securely.  
B. INDOOR WEATHER STATION  
1. Remove the battery cover. To  
do this, insert a solid object in  
the space provided at the  
lower-central position of the  
battery cover, then push up and  
pull out on the battery cover.  
Battery  
Cover  
2. Observe the correct polarity,  
and install 2 AA batteries.  
3. Replace the battery cover.  
Note: Immediately after the batteries have been installed, each LCD  
(Liquid Crystal Display) will flash and a tone will sound. Within a few  
seconds the indoor temperature will be displayed. If not, then remove the  
batteries for 10 seconds and reinstall. If the outdoor temperature is not  
displayed within four minutes, remove batteries from both units, wait 10  
seconds, and reinstall. The time will show -:-- and start searching for the  
WWVB signal. If it successfully receives the time signal (usually at night),  
it will display the correct time (default is Eastern).  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROGRAM MODE  
Programming Note: If 30 seconds are allowed to pass or either the IN or  
the OUT button is pressed during programming modes, the unit will set the  
last information entered—the display will stop flashing and return to  
normal time-date readings. If you don’t leave the program mode during the  
programming of sections III through VIII, you can advance to step 3 of the  
next program setting. If you do leave the program setting (or want to  
program a specific setting) follow each instructional step to program that  
setting.  
I. PROGRAMMING SEQUENCE  
The sequence for programming the indoor weather station and the default  
(factory) settings are:  
1. 12/24 hour time setting  
2. Time Zone  
12 hour  
Zo -5 (eastern)  
3. Daylight Saving Time  
4. Time – hour  
1 (on)  
12  
5. Time – minute  
00  
6. Date – day of the week  
7. Date – month  
mo (Monday)  
1 (January)  
8. Date – day of the month  
9. Date – Year  
10. Temperature  
11. LCD (liquid crystal display) contrast  
12. End of sequence  
1
1999  
°F  
5
The programming instructions are given in a manner so that each setting is  
done separately. On initial set-up and after inserting new batteries to  
program all functions simply disregard the first two steps of each section  
starting with the Time Zone Setting.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
II. FUNCTION KEYS  
The function keys are operated by pressing the top  
or bottom of the key corresponding to the  
operation that you want to perform.  
II. 12 OR 24 HOUR TIME SETTING  
1. Press and hold the “SET”  
button for 3 seconds or until  
“12 h” flashes in the DATE  
LCD.  
2. Press and release the “CH”  
button to toggle between 12  
and 24-hour time.  
3. Press and release the “SET” button to confirm the 12/24-hour  
setting and to advance to Time Zone Setting.  
III. TIME ZONE SETTING  
The default time zone is EST, “Zo -5” (Eastern Standard Time), to  
change this setting:  
1. Press and hold the “SET” button for 3 seconds or until “12 h”  
OR “24 h” flashes in the  
DATE LCD.  
2. Press and release the “SET”  
button 1 more time to enter  
the Time Zone setting mode.  
3. The default Time Zone “Zo-  
5” will flash in the DATE  
LCD.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Select your appropriate  
time zone using the  
Time Zones  
GMT  
0
-4  
-5  
-6  
-7  
-8  
-9  
-10  
“CH” button.  
selection of the Time  
Zone, the letter  
During  
Atlantic  
Eastern  
Central  
Mountain  
Pacific  
3
EST;  
CST;  
MST;  
PST;  
abbreviations for the time  
zones found in North  
America will flash across  
the top of the TIME  
LCD. Observe the chart  
ALA;  
HAW;  
Alaska  
Hawaii  
below,  
showing  
the  
corresponding  
abbreviations, time zones, and codes.  
Note: There are more time zones represented by numbers than there are  
represented by 3 letter abbreviations. If you live in North America you  
need only be concerned with the ones in the chart above.  
5. Press and release the “SET” button to confirm and advance to  
the Daylight Saving Time setting.  
IV. DAYLIGHT SAVING TIME (DST) SETTING  
1. Press and hold the “SET” button for 3 seconds or until “12 h”  
or “24 h” flashes in the DATE LCD.  
2. Press and release the “SET” button 2 more times to reach the  
DST selection mode.  
3. “DST 1” is the default setting  
and will be flashing in the  
DATE LCD.  
4. Press and release the “CH”  
button to select “DST 0” or  
“DST 1.”  
5. “DST 0” indicates that the feature is off and the WWVB will  
not change times automatically. “DST 1” indicates that the  
feature is on and the WWVB will change times automatically.  
Note: Some locations (Arizona and parts of Indiana) do not  
follow Daylight Saving Time and should select “DST 0.”  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Press and release the “SET” button to confirm and advance to  
the Time setting mode.  
V. TIME  
There are two methods by which the time can be set:  
A) Automatically via WWVB reception or  
B) Manually.  
A. WWVB (Remote Control Time)  
This method requires you to do nothing except wait for the signal  
to be received and to select a time zone. Reception usually takes  
approximately 6-10 minutes during optimal conditions. The best  
conditions for reception is at night, between midnight and 6:00  
AM—when there is less atmospheric interference. To keep your  
time as accurate as possible, the weather station conducts a  
WWVB search every night between these hours and overrides any  
manually set time. The WWVB tower icon (appearing in the TIME  
LCD) will flash when a signal-search is in progress, will remain  
steady when the signal has been received and nothing will be  
displayed in all other situations. If the WWVB time has not been  
received after 10 minutes of battery installation, you may manually  
set the time or leave the time function alone (once reception has  
occurred the WWVB time will over ride the manual time and set  
automatically).  
B. MANUAL TIME SETTING  
1. Press and hold the “SET” button for 3 seconds or until “12h”  
flashes in the DATE LCD.  
2. Press and release the “SET” button 3 more times.  
3. The hour digit (default of “12” should be flashing in the  
TIME LCD).  
4. Press and release the “CH” button to change the hour. Press  
the “CH” button once and the hour will increase by one,  
twice and the hour will increase by two, etc.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Press and release the “SET” button to confirm the hour  
setting and to advance to the minute setting mode.  
6. The minute digits should be flashing. Press and release the  
"CH” button to change the minutes—increasing the minutes  
by increments of 1 with each press of the “CH” button.  
7. Press and release the “SET” button to confirm the minutes  
and to advance to the Day, Date, and Year setting mode.  
Note: In 12h mode, “PM” will appear to the left of the time  
during PM hours. If the time is not within the PM hours, nothing  
will be displayed. Be sure to set the time to the correct AM/PM  
time to ensure automatic reception at optimal times.  
VI. SETTING THE DAY, DATE, AND YEAR  
1. Press and hold the “SET” button for 3 seconds, or until “12 h”  
or “24 h” flashes in the DATE LCD.  
2. Press and release the “SET” button 5 more times to reach the  
Weekday setting mode.  
Note: “MO” (representing Monday) is the default setting for the  
weekday, “1.1” is the default setting for the numeric month and  
day, and “1999” is the default setting for the year. The day, date,  
and year will be automatically set once the WWVB signal is  
received. However, the day, date, and year can be manually set  
and will flash respectively in the DATE LCD during manual  
programming.  
3. The weekday will be  
flashing in the DATE LCD,  
press and release the “CH”  
button to change the  
weekday.  
4. Press and release the “SET”  
button to confirm, and to  
enter the numeric-month setting mode.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. The numeric-month will be flashing in the DATE LCD. Press  
and release the “CH” button to select to the current month.  
6. Press and release the “SET” button to confirm the numeric-  
month, and to enter the numeric-day setting mode.  
7. The numeric-day will be flashing, press and release the “CH”  
button to select the current day.  
8. Press and release the “SET”  
button to confirm and to enter  
the year setting mode.  
9. The default-year will be  
flashing, press and release the  
“CH” to select the appropriate  
year.  
10. Press and release the “SET” button to confirm and to advance  
to the °F or °C setting mode.  
VII. SELECTING °F OR °C  
1. Press and hold the “SET” button for 3 seconds, or until “12h”  
or “24h” flashes in the DATE LCD.  
2. Press and release the “SET” button 9 times to reach the °F or  
°C setting mode.  
3. “°F” is the default setting, and  
should be flashing in the  
DATE LCD.  
4. Press and release the “CH”  
button to shift °F to °C and  
back.  
7. Press and release the “SET”  
button to confirm your  
selection and to advance to the LCD contrast setting.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIII. SETTING THE LCD CONTRAST  
1. Press and hold the “SET” button for 3 seconds or until “12h”  
or “24h” flashes in the DATE LCD.  
2. Press and release the “SET” button 10 more times to reach the  
LCD contrast setting mode.  
3. The default setting—“Lcd 5” will  
flash in the DATE LCD.  
4. There are 8 LCD contrast levels  
to choose from—“Lcd 0” is the  
lightest and “Lcd 7” is the  
darkest.  
5. Press and release the “CH”  
button to toggle through the settings.  
6. Press and release either the “IN” or “OUT” buttons to  
confirm all the settings and to exit the manual-programming  
mode (or wait 15 seconds for the unit to automatically return  
to the normal display mode).  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES OF THE WS-7076U  
WWVB Tower Icon (indicates  
time reception)  
Low Battery  
Alarm icon  
Satellite icon (indicates  
outdoor transmission)  
I. BACK LIGHT  
The WS-7076U has a backlight that can be activated by pressing any of the  
eight function buttons. After a button has been pressed the backlight will  
come on for five seconds before automatically shutting off.  
II. INDOOR TEMPERATURE  
The current indoor is displayed in the INDOOR LCD and is updated every  
10 seconds.  
III. OUTDOOR TEMPERATURE  
The outdoor temperature is viewed in the OUTDOOR LCD. The outdoor  
temperature is updated every five minutes. When there is more than one  
remote temperature sensor unit in operation, a “boxed” number will appear  
to the right of the temperature. This indicates which remote temperature  
sensor unit (1, 2, or 3) is currently displaying its data in the OUTDOOR  
LCD. (This feature is explained in further detail in section VIAdding  
Remote Temperature Sensors).  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IV. MINIMUM AND MAXIMUM TEMPERATURE RECORDS  
The WS-7076U keeps a record of the MINIMUM and MAXIMUM  
temperature and the time and date of their occurrence—for both the indoor  
and outdoor modes.  
A. VIEWING THE INDOOR TEMPERATURE RECORDS  
1. Press the “IN” button once. “MIN” appears in the upper  
portion of the flashing INDOOR LCD indicating that the  
minimum temperature and the time and date of occurrence are  
displayed. The minimum records will display for 20 seconds.  
2. Press the “IN” button again (once while “MIN” is still  
displayed, twice otherwise). “MAX” appears in the upper  
portion of the flashing INDOOR LCD indicating that the  
maximum temperature and the time and date of occurrence are  
displayed.  
3. While “MAX” is still displayed press the “IN” button again to  
return to the current data display. By waiting 20 seconds  
during either the minimum or the maximum readings the unit  
will automatically return to current data readings.  
B. VIEWING THE OUTDOOR TEMPERATURE  
RECORDS  
1. Press the “OUT” button once. “MIN” appears in the upper  
portion of the flashing OUTDOOR LCD, indicating that the  
minimum temperature and the time and date of occurrence are  
displayed. The minimum records will display for 20 seconds.  
2. Press the “OUT” button again (once while “MIN” is still  
displayed, twice otherwise). “MAX” appears in the upper  
portion of the flashing OUTDOOR LCD, indicating that the  
maximum temperature and the time and date of occurrence are  
displayed.  
3. While “MAX” is still displayed press the “OUT” button again  
to return to the current data display. By waiting 20 seconds  
during either the minimum or the maximum readings the unit  
will automatically return to current data readings.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C. RESETTING THE MIMIMUM AND MAXIMUM  
RECORDS  
1. All the indoor records (minimum and maximum) will be reset  
after the “IN” button is pressed and held for 5 seconds.  
2. All the outdoor records (minimum and maximum) will be  
reset after the “OUT” button is pressed and held for 5  
seconds.  
V. ALARM FUNCTION  
A. SETTING THE ALARM (alarms 1 and 2)  
Note: There are two alarms that can set. Each alarm will sound  
for a complete duration of 2 minutes.  
1. Press and hold the “AL1”  
button for 5 seconds or until  
the alarm-time display  
flashes in the DATE LCD.  
2. Press and release the “IN”  
button to set the alarm  
hours, press and release the  
“OUT” button to set the  
alarm minutes.  
3. Press the “AL1” button or  
wait 15 seconds for the unit to automatically confirm the  
alarm time and return to display the date in the DATE LCD as  
normal.  
4. The ((1)) icon, appearing in the DATE LCD, indicates that the  
alarm is set to sound at the programmed time.  
5. Programming the alarm time automatically activates the alarm  
to sound at the programmed time. To deactivate the alarm,  
press the “AL1” button (removing the ((1)) icon from the  
screen). To reactivate the alarm, press the “AL1” button  
again.  
6. After each activation or deactivation, the programmed alarm  
time is displayed. Wait 15 seconds and the date will display  
in the DATE LCD again.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. To set, activate and deactivate alarm 2, follow the directions  
above for alarm 1—using the “AL2” button instead of the  
“AL1” button. The ((2)) icon will represent activation and  
deactivation of Alarm 2.  
B. SNOOZING AND STOPPING THE ALARM  
1. The snooze function is activated by pressing any one of the  
following buttons: “SET”, “IN”, “OUT” or “SNZ”.  
2. To turn the alarm off completely, press any of these buttons:  
“CH”, “AL1”, “AL2” or “DATE”.  
3. The snooze function will last for 5 minutes before the alarm  
begins to sound again. Either the ((1)) or the ((2)) icon will  
flash during the snooze mode.  
VI. ADDING OUTDOOR REMOTE CONTROL SENDERS  
(OPTIONAL)  
The WS-7076U is able to receive signals from 3 different remote  
temperature sensors. The remote temperature sensor model(s) that you  
choose will come with their own set of instructions. Follow these  
instructions for a complete guide to setting up. Following are some brief  
instructions for the basic set-up of remote temperature sensor units with the  
WS-7076U. These extra remote temperature sensors can be purchased  
through the same dealer as this unit, or by contacting La Crosse Technology  
directly. A TX6U will monitor temperature only, a TX3U will monitor  
temperature and display the temperature on its LCD, and the TX3UP will  
monitor the temperature via a probe for measuring soil or water  
temperatures..  
Note: When setting up multiple units it is important to remove the batteries  
from all existing units in operation. Then insert batteries into all the  
remote temperature sensor units in numeric sequence. Second, install  
batteries into the indoor weather station. Transmission problems will arise  
if this is not done correctly and if the total time for set-up exceeds 6  
minutes.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A. SET-UP OF MULTIPLE UNITS  
1. It is necessary to remove the batteries from all units currently  
in operation.  
2. Remove the battery covers to all remote temperature sensor  
units.  
3. Place all remote temperature sensor units in a numeric  
sequential order.  
4. In sequential order, install batteries (follow the same battery  
installation procedures seen in section I. A) of the Detailed  
Set-Up Guide).  
5. Install batteries into the indoor weather station.  
6. Follow the Detailed Set-Up Guide for programming and  
operating instructions.  
B. VIEWING AND OPERATING WITH MULTIPLE  
REMOTE TEMPERATURE SENSOR UNITS  
1. To view the temperature of a different remote temperature  
sensor unit, press and release the “CH” button. A shift from  
one “boxed” number to the next should be observed in the  
OUTDOOR LCD.  
2. To view the Minimum/Maximum temperature: first select  
which remote temperature sensor to read data from (indicated  
by the “boxed” number), then press and release the  
“MIN/MAX” button. Pressing this button once will display  
the minimum temperature and the date and time the data was  
recorded. Pressing this button a second time (while “MIN” is  
still displayed, otherwise press the button twice) will display  
the same data for the maximum recordings.  
3. To reset the Minimum/Maximum readings, it is necessary to  
select which remote temperature sensor you wish to reset.  
Press and hold the “OUT” button for 5 seconds, the records  
for the selected remote temperature sensor unit will be reset.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNTING  
Note: Before permanently mounting ensure that the indoor weather station  
is able to receive WWVB signals from the desired location. Also, extreme  
and sudden changes in temperature will decrease the accuracy of the  
indoor weather station and changes in elevation will result with inaccurate  
weather forecasting for the next 12 to 24 hours. These changes will require  
a 12 to 24 hour wait before obtaining reliable data. To achieve a true  
temperature reading, avoid mounting where direct sunlight can reach the  
remote temperature sensor. We recommend that you mount the remote  
temperature sensor on a North-facing wall. The sending range is 80ft—  
obstacles such as walls, concrete and large metal objects can reduce the  
range. Place both units in their desired location and wait approximately 15  
minutes before permanently mounting to ensure that there is proper  
reception. The indoor weather station should display a temperature in the  
OUTDOOR LCD within 4 minutes of setting up.  
I. THE REMOTE TEMPERATURE SENSOR  
The remote temperature sensor can be mounted in two ways:  
with the use of screws, or  
using the adhesive tape.  
A. MOUNTING WITH SCREWS  
1) Remove the mounting bracket from the remote  
temperature sensor.  
2) Place the mounting bracket over the desired location.  
Through the three screw holes of the bracket, mark  
the mounting surface with a pencil.  
3) Where marked, start the screw holes into mounting  
surface.  
4) Screw mounting bracket onto the mounting surface.  
Ensure that the screws are flush with the bracket.  
B. MOUNTING WITH ADHESIVE TAPE  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1) With a nonabrasive solution, clean and dry the back  
of the mounting bracket and the mounting surface to  
ensure a secure hold. The mounting surface should  
be smooth and flat.  
2) Remove the protective strip from one side of the  
tape. Adhere the tape to the designated area on the  
back of the mounting bracket.  
3) Remove the protective strip from the other side of the  
tape. Position the remote temperature sensor in the  
desired location, ensuring that the indoor temperature  
station can receive the signal.  
II. THE INDOOR TEMPERATURE STATION  
The indoor temperature station can be mounted in two ways:  
with the table stand or  
on the wall with the use of a wall hanging screw (not  
included).  
A. USING THE TABLE STAND  
1) The indoor temperature station comes with the table  
stand already mounted. If you wish to use the table-  
stand all that is required is to place the indoor  
temperature station in an appropriate location.  
B. WALL MOUNTING  
1) Remove the table stand. To do this, pull down on the  
stand from the rear and rotate forward.  
2) Fix a screw (not included) into the desired wall leaving  
approximately 3/16 of an inch (5mm) extended from  
the wall.  
3) Place the indoor temperature station onto the screw  
using the hanging hole on the backside. Gently pull  
the station down to lock the screw into place.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Problem: No reception of WWVB time signal.  
Solution: 1) Wait overnight for signal.  
2) Be sure indoor weather station is at least 6 feet from any electrical  
devices such as televisions, computers or other radio-controlled clocks.  
3) Remove batteries for five minutes, reinsert and leave the unit alone  
overnight without pressing buttons.  
4) If there are still problems, contact La Crosse Technology.  
Problem: Hour is incorrect (minute and date are correct).  
Solution: Be sure correct time zone and daylight saving time is selected.  
Problem: The LCD is faint  
Solution: 1) Set the LCD contrast to a higher number  
2) Replace batteries  
Problem: No outdoor temperature is displayed.  
Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, then  
into the indoor temperature station.  
2) Place remote temperature sensor closer to the indoor temperature  
station.  
3) Be sure all batteries are fresh.  
NOTE: For problems not solved, please contact La Crosse Technology.  
MAINTENANCE AND CARE INSTRUCTIONS  
Extreme temperatures, vibration and shock should be avoided to prevent  
damage to the units.  
Clean displays and units with a soft, damp cloth. Do not use solvents or  
scouring agents. They may mark the displays and casings.  
Do not submerge in water.  
Immediately remove all low powered batteries to avoid leakage and  
damage.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Opening the casings invalidates the warranty. Do not try to repair the unit.  
Contact La Crosse Technology for repairs.  
SPECIFICATIONS  
Temperature measuring range:  
Indoor:  
32°F to 139.8°F with 0.2°F resolution.  
(0°C to 59.9°C with 0.1°C resolution)  
“OFL” displayed if outside this range  
-21.8°F to 157.2°F with 0.2°F  
resolution.  
Outdoor:  
(-29.9°C to 69.9°C resolution) “OFL”  
displayed if outside this range  
Every 10 seconds  
Indoor temperature checking  
interval:  
Outdoor temperature checking  
interval:  
Every 1 minute  
(Remote Temperature Sensor)  
Outdoor temperature reception:  
(Indoor Weather Station)  
Transmission Range:  
Every 5 minutes  
80 feet (in open space)  
Power Supply:  
Indoor Weather Station:  
Remote Temperature Sensor:  
Battery life cycle:  
2 x AA, IEC LR6, 1.5V  
2 x AA, IEC LR6, 1.5V  
Approximately 12 months  
Alkaline  
Recommended battery type:  
Dimensions (L x W x H)  
Indoor Weather Station (without  
stand):  
3.2” x 1.1” x 5.7”  
(81 x 30 x 145mm)  
1.57“ x 0.9“ x 5.04“  
(40 x 23 x 128 mm)  
Remote Temperature Sensor:  
WARRANTY INFORMATION  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against  
manufacturing defects in materials and workmanship.  
This limited warranty begins on the original date of purchase, is valid only on products  
purchased and used in North America and only to the original purchaser of this  
product. To receive warranty service, the purchaser must contact La Crosse  
Technology, Ltd for problem determination and service procedures. Warranty service  
can only be performed by a La Crosse Technology, Ltd authorized service center.  
The original dated bill of sale must be presented upon request as proof of purchase to  
La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.  
La Crosse Technology, Ltd will repair or replace this product, at our option and at no  
charge as stipulated herein, with new or reconditioned parts or products if found to be  
defective during the limited warranty period specified above. All replaced parts and  
products become the property of La Crosse Technology, Ltd and must be returned to  
La Crosse Technology, Ltd. Replacement parts and products assume the remaining  
original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd  
will pay all expenses for labor and materials for all repairs covered by this warranty. If  
necessary repairs are not covered by this warranty, or if a product is examined which  
is not in need or repair, you will be charged for the repairs or examination. The owner  
must pay any shipping charges incurred in getting your La Crosse Technology, Ltd  
product to a La Crosse Technology, Ltd authorized service center. La Crosse  
Technology, Ltd will pay ground return shipping charges to the owner of the product to  
a USA address only.  
Your La Crosse Technology, Ltd warranty covers all defects in material and  
workmanship with the following specified exceptions: (1) damage caused by accident,  
unreasonable use or neglect (including the lack of reasonable and necessary  
maintenance); (2) damage occurring during shipment (claims must be presented to  
the carrier); (3) damage to, or deterioration of, any accessory or decorative surface;  
(4) damage resulting from failure to follow instructions contained in your owner’s  
manual; (5) damage resulting from the performance of repairs or alterations by  
someone other than an authorized La Crosse Technology, Ltd authorized service  
center; (6) units used for other than home use (7) applications and uses that this  
product was not intended or (8) the products inability to receive a signal due to any  
source of interference.. This warranty covers only actual defects within the product  
itself, and does not cover the cost of installation or removal from a fixed installation,  
normal set-up or adjustments, claims based on misrepresentation by the seller or  
performance variations resulting from installation-related circumstances.  
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR  
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES  
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.  
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF  
CHILDREN’S REACH.  
This warranty gives you specific legal rights. You may also have other rights specific  
to your State. Some States do no allow the exclusion of consequential or incidental  
damages therefore the above exclusion of limitation may not apply to you.  
For warranty work, technical support, or information contact:  
La Crosse Technology  
2809 Losey Blvd. S.  
La Crosse, WI 54601  
Phone: 608.782.1610  
Fax: 608.796.1020  
e-mail:  
(warranty work)  
(information on other products)  
web:  
FCC ID: OMO-01RX (receiver), OMO-01TX (sensor)  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:  
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND  
2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED,  
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED  
OPERATION.  
All rights reserved. This handbook must not be reproduced in any form, even in  
excerpts, or duplicated or processed using electronic, mechanical or chemical  
procedures without written permission of the publisher.  
This handbook may contain mistakes and printing errors. The information in this  
handbook is regularly checked and corrections made in the next issue. We accept no  
liability for technical mistakes or printing errors, or their consequences. All trademarks  
and patents are acknowledged.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Automobile Accessories 701 137M User Manual
Lego Games 75037 User Manual
Lexmark Network Card x560 User Manual
Liebert Power Supply GXT 2U User Manual
Lincoln Automobile 2009 MKX User Manual
Logitech Mouse T400 User Manual
LOREX Technology Network Card DHU500 SERIES User Manual
Mackie Speaker HRS120 User Manual
Magnavox Universal Remote US2 MG53S User Manual
Marmitek Digital Camera 3GP User Manual