LG Electronics TV Mount PCM MS2 User Manual

I N S T A L L A T I O N M A N U A L  
Universal flat-panel mount  
R
LISTED  
E176225  
3130 E. Miraloma Ave. Anaheim, CA 92806 Phone: 800 368-9700 Fax: 800 832-4888  
PREMIER MOUNTS ©2004/ REV 02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly drawing  
Dimensions are in Inches and (mm)  
28.000  
(171.2)  
16.000  
(406.4)  
1.245  
(31.75)  
A
C
L
B
H
5.000  
(127)  
21.000  
(533.4)  
19.000 12.000  
(482.6) (304.8)  
10.500  
(266.7)  
C
L
5.000  
(127)  
C
G
16.000  
(406.4)  
D
16.000  
(406.4)  
16.000  
(406.4)  
F
24.290  
(616.97)  
E
Description  
2.331  
(59.21)  
A. Wall plates  
B. Mounting brackets  
C. Griplate™  
G
H
D. Mounting hardware  
E. M6 x 30 (mm) Phillip screws  
F. Wood stud  
1
G. 5/16” x 3” Lag screws and flat washers  
H. Safety knobs  
20.500  
(520.7)  
2
Fine tune tilt adjustments  
1. M5 Phillips screws for fine  
tension  
2. M8 Hex nut coarse tension  
NOTE: The 8 (mm) hex nut is for your  
coarse tension adjustment and the 5 (mm)  
screws are for your fine tension adjustment.  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Flat panel list  
Acer  
Eizo  
Idex  
PDP7859: M6 x 20  
5420T: M8 x 30  
PDM4260: M4 x 16  
Akai  
Electrograph  
Ikegami  
CTA42AR7A, PDP4247, PDP4290, PDP4294,  
PDP5090, HPT500AN: M8 x 25 – ½” nylon spacers -  
sleeves  
DTS42W: M8 x 30 – ¼” nylon spacers (large)  
DTS4230: M8 x 30 – ½” nylon spacers - sleeves  
DTS42DD, DTS42GBDD, DTS42GB: M6 x 20  
PTM4202: M5 x 20  
Akira  
Faroudja  
Integra  
EPM420, SV4201: M5 x 16  
FPP42HD10, FPP50HD10: M4 X 16  
PLA50V1: M4 X 16  
Albatron  
Fujitsu  
JVC  
PWV46AC: M6 x 20  
4211, 4212, 4221, 4222, 4208, 4209, 4213, 4214, 4229,  
4241 4242, 4233: M5 x 16  
5001, 5002, 5003, 5004, P50XHA10, P50XCA11UH,  
P50XHA30WS: M8 x 25 – flat washers  
PDS6101, PDS6001, PDS6002: M8 x 30 – ½” Nylon  
spacers - sleeves  
GDV4200PZW, 4210, GDV4210PZWGA, 4211,  
GMP420UG, GMV42UG, JVP042WV74, PD42WV74,  
PD42WX84: M5 x 16  
GDV500PZU, GDV501U, 502U: M8 X 30 – ½” nylon  
spacers – sleeves  
Barco  
Cineversum 50: M8 x 20  
BenQ  
Gateway  
LG Electronics  
PDP7843E: M6 x 20 – ¼” nylon spacers (small)  
PDP46W1: M6 X 12  
GTWP42M102: M8 x 20, M8 x 35 – ¼” nylon spacers  
(large)  
Flatron MU40PA10B, MU40PA15B: M5 x 20- ¼” nylon  
spacers  
GATEWAY 42: M8 x 30 – ¼” nylon spacers  
GATEWAY 46: M6 x 20  
GATEWAY 50: M8 x 30 – ¼” nylon spacers  
Flatron MN42PZ10, MN42PZ11, MU42PZ10,  
MU42PZ11B, MU42PZ15B: M5 x 20  
MU50PZ41, MU50PZ90: M5 x 20  
Flatron MU60PZ10, MU60PZ11B, MU60PZ12B,  
MU60PZ90V: M8 x 25  
Cornea  
MP4200, MP4204: M5 x 16  
Helios  
Dream Vision  
Luce  
4200: M8 x 20  
Revolution One, Revolution Five: M4 x 16  
PDTV4220A: M5 x 25 – ½” nylon spacers  
Dukane  
Hitachi  
Marantz  
P37: M6 x 12  
P42: M6 x 12  
P50: M8 x 20  
32HDT20,CMP307XJ,CMP307XU,32HDT20  
CMP401HDU, CMP402HDE, CMP402HDU,  
CMP4120HDU,CMP4121,CMP4121HDU,CMP4201U,  
CMP4202U, 42HDW10,42HDT20, 42HDT50, 42HDT55  
M6 x 12  
PD4280D, PD4282D, PD4290D, PD4292D,  
PD4293: M4 x 20  
PD4298HD: M6 X 20  
Dwin  
PD501OD, PD5020, PD5040:  
CMP5000WXU, CMP5003WXU, 50HDT50, 50HDT55:  
M8 X 20  
HD50: M8 x 30 – ½” nylon spacers - sleeves  
Max  
EIKI  
4600, 4600T: M6 x 20  
5000: M8 x 30- ½” nylon spacers - sleeves  
PLD42XU: M5 x 20 - ¼” nylon spacers (small)  
NOTE: If your flat panel display is not listed, go to (page 8) to determine the thread pitch for your flat panel.  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mitsubishi  
Princeton Graphics  
Tatung  
AR3.4FTW,AR4.6PDP: M6 x 20  
PD5010HD, PD5030: M4 x 16  
P46T: M6 x 20  
Monivision  
Rainbow  
Toshiba  
42HP82: M4 X 16  
PWV46AC, PD46W00: M6 x 20  
Spectrum 3750: M6 x 20  
PD42W, PD42W1: M8 X 30 – ½ ” nylon spacers  
(large) - sleeves  
50HP81: M8 X 30 – ½” nylon spacers (large) - sleeves  
50HP82: M4 X 16  
RCA  
NEC  
PR42300, PHD42600, PHD50300, PHD50400: M4 X 16  
4200W, 4210W, M4A,MP2, PX42M3A, 42PD1W, PD2  
M5A,M5G, 42MP1, 42PD1, PX42VM1A, PX42VP1A,  
PX42VP2A, 42MP3, 42PD3, PX42VP3A, 42MP4,  
42VP4A, 42MX2: M4 X 16, 5000W, PX50M5A, 50PD1,  
PX50VP1A, PX50MX1A, 50MP1, 50MP2, 50PD2,  
50VP2, 50MP3,  
PHD50500: M8 X 20  
Tredex  
TXP4600: M6 x 20  
Revox  
V-Inc  
E1042: M6 x 20  
E1050: M8 x 20  
50XM3: M4 X 16  
Vizio P1, Vizio P4: M6 x 12  
Norcent  
Runco  
Vidikron  
46WGA850: M6 x 12  
PL42C, CW42: M4 X 16  
PL42CXPL50CX: M8 X 30, ½” Nylon spacers –  
VPW420: M8 X 30, ½” Nylon spacers (large) - sleeves  
sleeves  
Orion  
E1050, PL50C, PL50HDX, CW50MC: M8 X 20  
VIEWSONIC  
PM4202: M5 x 16  
Sampo  
VPW420: M8 x 30 – ½” nylon spacers - sleeves  
VPW425: M8 x 30 – ¼” nylon spacers (large)  
VPW450HD: M8 x 30 – ¼” nylon spacers (large)  
VPW500: M8 X 20  
PME42S6: M8 x 30 – ¼” nylon spacers (large)  
PME42F61: M8 x 20, M8 x 35 – ¼” nylon spacers  
(large)  
Panasonic  
VPW505: M8 x 30 – ¼” nylon spacers (large)  
TC42P1, PT42PD3P, PT42PD1P, TC42P1F, PT37P1,  
TH42PWD3, TH37PWD4UZ, PT37PD4, TH37PW5EX,  
TH37PA20UP, TH42PD4UY, TH42PWD4EX, PT42P1,  
42PD2, TH42PWD3U, TH42PHD5U, PT42PD3P,  
PT42PD4, PT42PHD4P, TH42PWD5UY, TH42PW5UZ,  
TH42PWD6UY, TH42PA20UP, TH42PL20E,  
TH42PAX20, TH50PHD3U, PT50PD3P, PT50PHD4P,  
TH50PHD3E, TH50PHW3, TH50PD4, TH50PHD5UY,  
TH50PHD6UY, TH50PL20E, TH50TX20UP:  
M8 X 30 – ½” Nylon spacers – sleeves  
PME50X6: M8 x 30 – ¼” nylon spacers (large)  
Yamaha  
Samsung  
PDM1: M8 x 30 – ½” nylon spacers - sleeves  
PPM42S2, PPM42S3, SPL4225K, SPN4235, SPN4239:  
SPK4215M, PK42P2S: M8 x 25 – ½” nylon spacers  
PPM50H2, HPL5025K: M8 x 30 – ½” Nylon spacers -  
sleeves  
Zenith  
DPDP40W, P40V22,DPDP40V, P40V24: M5 x 20 – ¼”  
nylon spacers (small)  
P42W22, P42W22B, P42W24P, P42W34P: P40V24:  
PPM50H3, HPN5039: M8 x 25 – ½” nylon spacers  
TH42PX20U, TH50PX20U: M8 X 70 – 1-1/2” Nylon  
spacers  
Sanyo  
M5 x 20 – ¼” nylon spacers (small)  
P50W26, P50W28, P50W38: M5 x 16  
PDP421A: M5 x 20 - ¼” nylon spacer (small)  
Philips  
PDP42H1NA: M5 x 20 - ¼” nylon spacer (small)  
NOTE: If your flat panel display is not  
listed, go to (page 8) to determine the  
thread pitch for your flat panel.  
42FD9934, 42FD9952, 42FD9954, 42PH9555,  
42FD9935: M5 x 25 ½” Nylon spacers  
BDS4611: M6 x 20  
Sharp  
PZ42H2U, PZ43HV2U, PD50U, PZ50HV2U: M8 X 20  
50FD9934/17S: M4 X 16  
Pioneer  
SONY  
PDPV401, V402, PDP4330HD, PDP433HDE,  
PDP433CMX, PDP433PU, PDP4300, PDP4340HD,  
PRO800HD, PRO800HDI, PRO910HD, PDP4310,  
PDP501X, V502MX, V502X, PDP503MX, V505,  
PDP505HD, PRO1000HD, PDP503CMX, PDP5030HD,  
PDP503HDE, PDP5031HD, PDP5040HD,  
PFM42B1,PFM42B2: M6 x 20 - 5/16” flat washers  
PFM-42V1,PFM-42V2: M6 x 20”- 5/16” flat washers  
PFM50C1: M5 x 20 - 5/16” flat washers  
KE-42XBR900: M5 x 20 - 5/16” flat washers  
KE50XBR900: M5 x 20 - 5/16” flat washers  
KE42XS910: M5 x 20 - 5/16” flat washers  
KDE61XBR950: M5 x 20 - 5/16” flat washers  
PRO1000HDI,PRO1110HD: M8 X 20  
Planar  
SVA  
42N: M4 x 16  
50P: M8 x 20  
HD4208TIII: M6 x 20 - ¼” nylon spacers  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts list  
NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are  
missing before beginning installation. If there are parts missing stop the installation and contact Premier Mounts.  
Actual screw size  
(Qty 8)  
(Qty 6)  
M4 x 16  
M4 x 25  
M6 x 20  
M6 x 30  
(Qty 4)  
(Qty 2)  
(Qty 8)  
M5 x 12  
M5 x 16  
M8 x 20  
M8 x 25  
(Qty 6)  
(Qty 6)  
(Qty 6)  
M5 x 20  
M5 x 25  
M5 x 50  
(Qty 6)  
(Qty 4)  
M8 x 30  
(Qty 6)  
(Qty 4)  
(Qty 4)  
M8 x 35  
M8 x 70  
(Qty 8)  
M6 x 12  
(Qty 4)  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts list (con’t)  
Nylon spacers and flat washers  
actual size  
NOTE: The nylon spacers may be staked to achieve proper spacing.  
9/16" Nylon spacers  
(Qty 6)  
1/4" Nylon spacers  
(large)  
(Qty 6)  
1/2" Nylon spacers  
(large)  
Nylon sleeves  
(Qty 4)  
(Qty 12)  
5/16" Flat washers  
(metal)  
(Qty 6)  
1" Nylon spacers  
(Qty 6)  
1/4" Nylon spacers  
(small)  
(Qty 6)  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking the thread depth on your flat panel  
1. Insert the thread depth  
indicator (supplied)  
through the thread inserts  
found on the back of the  
Figure 1  
flat panel to make sure the  
inserts measure the same  
full depth and mark it.  
(see figure 1)  
2. Locate the correct  
diameter screw for the  
thread insert. Compare  
your marking to the  
screws (supplied). If your  
selected screw is longer  
than the marking on the  
thread depth indicator DO  
NOT USE this screw.  
The screw length must not  
bypass the marking. Select  
Inverted flat panel  
another screw size  
display  
(see figure 2 and 3). Until  
you find one that comes  
closest to your mark  
without going past.  
Marking the depth  
Thread insert  
Thread depth  
indicator  
Figure 2  
Screw  
Marking  
Thread depth indicator  
Figure 3  
Screw  
Marking  
Thread depth indicator  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts list (con’t)  
All of these parts are used to install the mounting bracket. Make sure that none of these parts are missing before beginning  
installation. If there are parts missing stop the installation and contact Premier Mounts.  
Level (1)  
Griplates™ (8)  
M6 x 12 Safety knobs (2)  
Wall plates (2)  
Mounting brackets  
(left & right)  
5/16" flat washers (8)  
5/16" x 3" Lag bolts (8)  
(used on wood studs  
only)  
M6 x 30 Lateral shift  
locking screws (2)  
Thread depth  
indicator (1)  
Template (1)  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Finding center of the flat panel display  
WARNING : Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could  
result in serious personal injury and possible damage to the flat panel.  
WARNING!  
INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO  
DO SO WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. THE  
FLAT PANEL IS HEAVY AND FRAGILE. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT.  
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.  
Once the flat panel is inverted, use a measuring  
tape to find the center of your flat panel measuring  
from outside to outside of the chassis. See figure 1.  
Top of flat  
panel  
C
L
Measuring  
Inverted flat panel  
tape  
Bottom of flat  
panel  
Using a pencil lightly mark the center of your flat  
panel.  
See figure 2.  
Inverted flat panel  
C
L
Mark the center of  
the flat panel  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Positioning the mounting brackets  
CAUTION: Check the chart on page 4 and 5 to see if  
your flat panel needs nylon spacers. The nylon spacers  
provided, must be used. Failure to do so will result in  
damaging the flat panel.  
Nylon spacers if  
Applicable  
(see chart) on page 4 and 5  
Install the nylon spacers to the mounting points on the  
flat panel see figure 3.  
NOTE: See chart (if the nylon spacers apply to your  
flat panel).  
Center mark  
Inverted flat panel  
Lay the left and right mounting  
brackets (stamped arrows facing out).  
See figure 4.  
Mounting brackets  
Bottom of flat  
panel  
Arrows facing out  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Match the center of viewing guide with the center  
line you marked in step 1.  
See figure 5.  
C
L
Bottom of flat  
panel  
Align the  
mounting brackets  
Mounting bracket  
The mounting brackets are designed with a center  
of viewing guide on the side of them.  
See figure 6.  
Bottom of flat  
panel  
Center of  
viewing guide  
Center of flat  
panel  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing the mounting brackets  
DIMPLES  
The Griplates™ have M4, M5 M6 and M8 hole  
patterns to fit the hardware that your flat panel  
requires.  
M8  
EXAMPLE: If your plasma uses M8 x 20 Phillip  
screws. Use the M8 mounting points. See figure 7  
M6  
Pre install two (2) M6 x 30 (mm) Phillip pan screws to  
the bottom of the left and right hand side mounting  
brackets. Once the mounting brackets are aligned secure  
the Griplate™ to the flat panel.  
M5  
NOTE: The dimples of the top plates have to be facing  
up and the bottom dimples must be facing down.  
Use (1) Griplate™ per mounting point. See figure 8.  
M4  
Phillips screw  
driver  
DIMPLES  
FACING UP  
DIMPLES  
FACING UP  
Bottom of flat  
panel  
DIMPLES  
FACING DOWN  
DIMPLES  
FACING DOWN  
CAUTION: Do not over tighten the mounting  
hardware.  
NOTE: Secure the two (2) M6 x 30 Phillip pan  
screws to the left and right mounting bracket.  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Finding the wood studs behind the wall structure  
Using a (commercially available) wood stud finder,  
locate the 16" or 24" stud centers behind the wall.  
Once found, make a pencil marking on the center of  
the wood studs.  
Wood stud finder  
(commercially available)  
See figure 9.  
Mark the wall and  
the center of the  
wood studs.  
NOTE: The wall plates have (3) 16" and (1)  
24" mounting slot positions.  
(Look at the assembly drawing on page 3)  
16"  
Wood studs  
behind the wall  
structure  
16"  
16"  
Center of  
viewing port  
Mark the  
bottom of the  
carton template  
Carton  
template  
Align the center viewing port from the carton template to  
the center of the wood studs horizontally. Match the  
center of viewing port to the center of viewing height  
desired and mark a line on the bottom of the carton  
template.  
Center of  
viewing mark  
See figure 10.  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Marking the bottom plate mounting points  
Place the upper portion of the bottom wall plate to the  
reference line and mark the four (4) lag bolt mounting points  
through the wall plate slots on the wall. Level the wall plate  
with the reference arrow pointing up to the ceiling.  
See figure 11.  
Wallplate  
16"  
Mounting  
slots  
Woodstuds  
Drill gun  
Level  
Pilot holes  
Drill four (4) ¼" pilot holes to the marked  
wall.  
See figure 12.  
16"  
- 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing the bottom wall plate  
Level  
Level and secure the plate to the wall with  
the reference arrow facing up to the ceiling.  
Secure the plate using the four (4) 5/16" lag  
bolts and flat washers (supplied). See figure  
13.  
CAUTION: Do not over tighten the lag bolts.  
Wall plate  
(4) 5/16" x 3" lag bolts  
and (4) flat washers  
(supplied)  
Marked wall  
When the bottom wall plate is properly  
installed to the wall. Lay the carton template on  
top of the wall plate.  
Lay the top wall plate on top of the cardboard  
template and mark the four (4) lag bolt  
mounting points.  
See figure 14.  
Template  
Wall plate  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing the top plate  
Drill four (4) ¼" pilot holes to the  
marked wall. See figure 15.  
Wall marks  
Wall plate  
- 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Level and secure the plate to the wall with  
the reference arrow facing up to the ceiling.  
Secure the plate using the four (4) 5/16" lag  
bolts and flat washers (supplied). See figure 16  
CAUTION: Do not over tighten the lag bolts.  
NOTE: CHECK THE MOUNT FOR PROPER  
TIGHTNESS AND SECURITY.  
Power source  
area  
Wall plates  
- 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing the flat panel to the wall mount  
WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO  
DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.  
Raise the flat panel with the LEFT and RIGHT mounting brackets secured  
to the flat panel and insert the top and bottom hooks from each bracket to  
the rods from the wall plates. See figure 17.  
TOP  
BOTTOM  
- 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Make any lateral shift adjustment and lock it  
by tightening the two (2) M6 x 30 (mm)  
Phillips screws found on the bottom of the  
mounting brackets.  
CAUTION: Do not over tighten the M6  
screws to the rods.  
See figure 18  
Lateral shift  
M6 x 30 Lateral  
shift screw  
- 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lateral shift adjustment  
Tilt the flat panel and secure the two (2) M6 x 12 (mm)  
safety knobs to each of the mounting brackets.  
See figure 19.  
M6 x 12  
Safety knobs  
NOTE: To remove the display from the wall simply extend the display to its maximum tilt range, remove the two 6 (mm) safety  
knurl knobs push the flat panel back to it’s flat position loosen or remove the two (2) M6 x 30 lateral shift screws and lift the  
unit of the wall.  
- 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NORTH AMERICA  
3130 East Miraloma Avenue  
Anaheim, CA 92806 USA  
USA and Canada –  
EUROPE  
ASIA  
Swallow House,  
Yabara 1916-15,  
Shilton Industrial Estate,  
Shilton, Coventry, England CV79JY  
Phone: +44 (0) 2476 614700  
Fax: +44 (0) 2476 614710  
Misato-machi, Gunma-gun  
Gunma-ken 370-3107, Japan  
Phone: 81.27.371.6998  
Fax: 81.27.371.6308  
Phone: 800-368-9700  
Fax: 800-832-4888  
Other Locations – Phone: 001.714.632.7100; Fax: 001.714.632.1044  
©Premier Mounts 2004  
- 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kyocera Cell Phone VMS130 User Manual
Land Pride Lawn Mower AFM40 User Manual
Lennox International Inc Heating System 15GCSX User Manual
LG Electronics Refrigerator LRSC21951ST User Manual
Life Fitness Fitness Equipment Ab Crunch User Manual
Lincoln Electric Welder UWW 170 User Manual
Lux Products Thermostat P521Ua User Manual
Magic Chef Blender EWBL20SG User Manual
Maverick Ventures Thermometer ET 41 User Manual
Maytag Washer FAV6800 User Manual