LG Electronics Door NL 7000 AC User Manual

Kantooradres:  
Postadres:  
Vlijtstraat 40  
Postbus 127  
NL-7005 BN Doetinchem  
H.R. te Arnhem nr: 09087869  
BTW nr: NL 8038.72.987.B01  
NL-7000 AC  
Tel: (+31) 314 376 876  
Fax: (+31) 314 376 878  
LA GARD Locks BV  
OPERATING INSTRUCTIONS LG 39E Multi User Combogard /Swingbolt  
Keypad 3035, 3710, 3750 or 3750K with reading contact  
Lock 39E  
Contact of  
the audit trail  
LED  
3750  
3750K  
3035  
3710  
Generally  
Each pressing of a key is confirmed by a signal (an acoustic signal and a LED flash). A valid code is  
followed by a double signal, an invalid code by a triple signal. After an interval of more than 10-seconds,  
the already entered part of the code is deleted and the entire sequence has to be re-entered.  
Code entering:  
a) Operation with parallel code:  
(manager mode)  
Enter the seven-digit numeric code–or a word with 7 characters  
a double signal is followed.  
Manager code: 1234567  
b) Operation with dual codes:  
(must be programmed)  
Six-digit numeric codes or words with six characters.  
For opening two valid codes must be entered.  
Manager code: 123456 and User ID# 654321  
Opening:  
Locking:  
Combogard: Enter the code and (after double signal) turn the  
entry clockwise within 3 seconds unto the hold. The lock is open  
and the entry is rotated.  
Swingbolt: Enter the code and (after double signal) turn the  
handle within 3 seconds into the OPEN position.  
If the lock is not opened within 3 seconds, it is automatically  
locked again.  
Combogard: Turn the entry counter-clockwise unto the hold.  
The lock is automatically closed and the entry stands straight.  
(Check this by trying to turn the entry back again)  
Swingbolt: Turn the handle into the CLOSE position.  
The lock is automatically locked; check this by trying to turn the  
handle into “OPEN” position.  
I M P O R T A N T  
Check the lock to be locked.  
Wrong try penalty:  
After four invalid codes, the entry is blocked for about 5  
minutes. During this period, the lock signals at 10-second  
intervals. After this time penalty, the entry of every second  
invalid code initiates a new 5 minutes delay period.  
The key pressing is refused with a triple signal.  
Change of code:  
(always with open door)  
The user can change its code anytime.  
Enter the code and keep pressed the last number until second  
double signal (LED is on), press the “0” and enter the new code  
(double signal), enter the new code once more for confirmation  
(double signal).  
The new code is now valid. If mistakes are made while  
changing the code or if an interval occurs of more than 10  
seconds, the old code remains valid and the entire sequence  
has to be re-entered.  
Test the new code several times by open door!  
LG 39E Combogard EN  
Revise: 1  
Datum: 16-02-05  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Kantooradres:  
Postadres:  
Vlijtstraat 40  
Postbus 127  
NL-7005 BN Doetinchem  
H.R. te Arnhem nr: 09087869  
BTW nr: NL 8038.72.987.B01  
NL-7000 AC  
Tel: (+31) 314 376 876  
Fax: (+31) 314 376 878  
LA GARD Locks BV  
Manual programming  
Factory Mode  
(Pre-Setup-mode)  
LG 39E Multi User  
The lock maybe mounted in the factory mode. It opens when  
pressing key “1” and it sends a silent alarm signal.  
The advantage is that there is only 1 version storage and an  
easy use during mounting.  
Exit the Factory-Mode  
Keep pressed the key “0” until the double signal (4-5  
seconds). Now the manager code is 555555.  
Code length and program selection The code length and program selection are made with the  
(6-9 digit code length is possible)  
function “8” in a group of 2 digits. The first digit is the code  
length and the second one is the program number.  
Program 0 = Manager mode (operation with parallel code)  
Program 1 = Manager mode with delay override  
Program 2 = Operation with two codes  
Program 3 = Two code operation with delay override  
Program 4 = Manager mode with alarm  
Program 5 = Manager with alarm and with delay override  
Program 6 = Two code operation with alarm  
Program 7 = Two code operation, alarm and delay override  
Programming  
(function 8)  
Enter the manager code “555555” and keep pressed the  
last number until the double signal is repeated (LED is on)  
and enter “8”. Enter the group of 2-digits (code length and  
program number) double signal and repeat the group for  
confirmation (double signal).  
In case of the 7-digit codes the manager code is 7x “5”.  
Install (Enable) user  
(function 1)  
Enter manager-code and keep last digit pushed until LED  
stays on. Press „1“ (double signal) and enter user-ID Nr. f.i.  
„1“ (double signal). Enter user code (double signal) and to  
confirm, enter the code again. Double signal and LED  
extinguished.  
In case a new code is not accepted (3-time-signal), this code  
is too similar to an already existing code. Select new code.  
NOTE: Users who are not installed in this stage will be  
blocked after changing the manager code!  
Program “freeze”  
After changing the manager code the program is „frozen“ and  
the program settings can only be changed after a reset to  
Factory Mode.  
Reset to Factory Mode  
In case the manger code is lost or the setting of the lock has  
to be changed, a reset can be executed by means of the  
RESET-BOX (PN#6066). Unplug battery from the lock or  
entry.  
Push the "0" button for ca. 3 minutes (or leave it for  
10minuts powerless) and plug the RESET-BOX in the BAT-  
connection of the lock. Wait until a longer signal. (0,5 sec)  
The Reset-Box requires a connected 9V-DURACELL  
ALKALINE-battery.  
The lock is in FACTORY MODE. Disconnect Reset-Box and  
plug battery back again. Lock opens with “1”.  
Safety notice: Do not assign code to the users of no use for the time being.  
Remove the codes. (Function 3 and user number)  
LG 39E Combogard EN  
3
Revise: 1  
Datum: 16-02-05  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Krell Industries Stereo Amplifier PAM 5 User Manual
Lantronix Printer 900 603 User Manual
Lenovo Computer Monitor 6135 HE1 User Manual
LG Electronics Computer Drive HT762TZW User Manual
LightSpeed Technologies Stereo System LES 370 Series User Manual
Linear Garage Door Opener AUH S User Manual
Logitech Computer Accessories MK270 User Manual
Marquis Hot Tub Everyday Hot Tub User Manual
Maytag Dishwasher MDB7100AWW User Manual
Maytag Dryer Accessories SL 3 User Manual