User’s Guide
W2600H
W2600HP
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand base or Removing the stand base
1.
Place the monitor with its front facing downward on a cushion or soft cloth.
2
.
Align the hooks on the Stand Body with the matching slots in the Stand Base.
Insert the hooks into slots.
3.
Hook
Stand Body
Stand Base
Slot
Warning
The tape and locking pin may only be removed from those monitors equipped with a
standing base when the base is pulled up.
Otherwise, you may be injured by the protruding sections of the stand.
A3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
4. Attach the monitor to the Stand Base by turning the screw to the right.
Screw : Turn the screw by using the screw handle.
5. Lift and turn the monitor to face towards the front after the connection is
made to the female part of the cable you're attaching.
6. Take the screw out by turning to the left to separate the monitor and Stand
Base.
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
A4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚
Swivel Range : 350˚
Height Range : maximum 3.94 inch (100.0mm)
100.0mm
* Please be sure to
remove the Locking
pin to adjust the height.
Ergonom ic
You do not need to replace the Locking pin after it is removed, to adjust its height.
It is recommended that in order to maintain an ergonomic and comfortable
viewing position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the screen, do not put your finger(s) in between
the head of the monitor and the stand body. You can hurt your finger(s).
A5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
Using the Computer
1. Make sure to turn off the computer and product.
1
Connect signal cable
the signal cable.
and power cord
in order, then tighten the screw of
2
A
Connect D-sub Cable (PC)
Connect D-sub Cable (Mac)
Connect DVI-D Cable
B
C
NOTE
This is a simplified representation of the
rear view.
This rear view represents a general
model; your display may differ from the
view as shown.
Signal Cable
Varies according to model.
Power Cord
1
2
Mac adapter
For Apple Macintosh use, a
separate plug adapter is
needed to change the 15 pin
high density (3 row) D-sub
VGA connector on the
Wall-outlet type
PC
supplied cable to a 15 pin 2
row connector.
MAC
PC
DVI-D(This feature is not
available in all countries.)
2. Touch the power button on the front of panel to turn
Power button
the power on. When monitor power is turned on, the
'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
NOTE
Self Image Setting Function'? This function provides the user with optimal display settings.When the user connects
'
the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
'AUTO/SET Function'? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen
while using the device or after changing screen resolution, touch the AUTO/SET function button to improve resolution.
A6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
Connecting the USB(Universal Serial Bus) Cable
"USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals
conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and
other peripherals to your display instead of having to connect them to your computer. This will give you
greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a
single USB port; and you can “hot” plug (attach them while the computer is running) or unplug them while
maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUS-
powered USB hub, allowing up to 2 other USB devices to be attached it.
1. Connect the upstream port of the display to the downstream port of the USB compliant
PC or another hub using the USB cable. (Computer must have a USB port)
2. Connect the USB compliant peripherals to the downstream ports of the display.
USB downstream Port x (4)
Connect the cables from USB
compliant peripherals-such as
mouse, memory stick or USB hard disk, etc.
USB upstream Port x (1)
Connect to downstream connectors of desktop
or laptop computers. (However, the computer
must support USB and have the USB port.)
3. The monitor’s USB terminal supports USB 2.0 and High Speed cables.
High Speed
480Mbps
2.5W
Full Speed
12Mbps
2.5W
Low Speed
Data Rate
Power
1.5Mbps
2.5W
Consumption
(Max,each Port) (Max,each Port)
(Max,each Port)
NOTE
To activate the USB hub function, the display must be connected to a USB compliant
PC(OS) or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the shape of the connector at the cable
side matches the shape at the connecting side.
Even if the display is in a power saving mode, USB compliant devices will function
when they are connected the USB ports(both the upstream and downstream) of the
display.
A7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Display
To arrange the cables
Connect the power cord and the signal cable as shown in the figure and then fix them
to the cable holders 1 and 2.
2. Please put the power cord and
1. Please insert the cable holder1
into the hole.
the signal cable in the cable holder 1.
Cable holder 1
3. Please put the power cord and the signal cable in the cable holder 2.
While pressing the bottom of cable holder 2 with one hand, pull the top of
it with the other hand as shown in the picture.
Pull
Press
Cable holder 2
A8
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Functions
Front Panel Controls
At the current display, Use 'EZ Zooming' Key, then the display
resolution is transferred to the one step low resolution.
Use 'EZ Zooming' Key one more, the display is back to the
original display.
ZOOMING
Those with poor eyesight such as the elderly, those who have difficulty using
computers and children can enlarge text or pictures by adjusting resolution with a
single touch.
To use this feature, please install forteManager program in the enclosed CD-
ROM.
Recommend resolution are 1920x1200, 1680 x 1050, 1600 x 1200, 1280 x 1024,
1024 x 768, 800 x 600.
The setting method can differ by O/S or video card. In this case, Please ask to the
computer or the video card manufacturer.
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Touch the MENU button for several seconds. The
message "OSD LOCKED" should appear.
If you want to unlock, touch the MENU button again for
several seconds. The message "OSD UNLOCKED"
should appear.
A9
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Functions
Use these buttons to select or adjust functions in the On
Screen Display.
Buttons
For more information, refer to page A17.
Use this button to make D-Sub or DVI connector active.
This feature is used when two computers are connected
to the display. The default setting is D-Sub.
(SOURCE Hot key)
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always touch
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
26 inch monitor : 1920 x 1200
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
A10
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
Touch the MENU Button, then the main menu of the OSD appears.
To access a control, use the
or
Buttons. When the icon you want
becomes highlighted, touch the AUTO/SET Button.
Use the
/
Buttons to adjust the image to the desired level. Use the
AUTO/SET Button to select other sub-menu items.
Touch the MENU Button once to return to the main menu to select another
function. Touch the MENU Button twice to exit from the OSD.
A11
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
BRIGHTNESS
CONTRAST
GAMMA
A
D
Reference
PICTURE
To adjust the brightness,
contrast and gamma of the
screen
sRGB
To customize the color of
the screen
COLOR
PRESET
6500K
9300K
RED
GREEN
BLUE
To adjust the position of the
screen
HORIZONTAL
POSITION
VERTICAL
CLOCK
To improve the clarity and
stability of the screen
PHASE
TRACKING
SHARPNESS
LANGUAGE
SETUP
To customize the screen
status for a user's operating
environment
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
SOUND
4:3 IN WIDE
FACTORY RESET
MOVIE / TEXT
FLATRON
F-ENGINE
To select or customize
desired image settings
USER
NORMAL
: Adjustable
A : Analog Input D : Digital Input
NOTE
The order of icons may differ depending on the model (A12~A17).
A12
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Touch the MENU Button, then the main menu of the OSD appears.
Menu Name
P I C T U R E
Sub-menus
Icons
Button Tip
MENU
: Exit
: Adjust (Decrease/Increase)
: Enter
D E
SET
: Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
A13
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
P I C T U R E
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
COLOR
Select the screen color.
PRESET
• sRGB: Set the screen color to fit the
SRGB standard color
C O L O R
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A14
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
POSITION
P O S I T I O N
To move image left and right.
To move image up and down.
HORIZONTAL
VERTICAL
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
TRACKING
T R A C K I N G
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
PHASE
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
SHARPNESS To adjust the clearness of the screen.
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A15
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
To choose the language in which the
control names are displayed.
LANGUAGE
SETUP
OSD
POSITION
To adjust position of the OSD window
on the screen.
WHITE
BALANCE
If the output of the video card is different
the required specifications, the color level
may deteriorate due to video signal
distortion. Using this function, the signal
level is adjusted to fit into the standard
output level of the video card in order to
provide the optimal image.
Activate this function when white and
black colors are present in the screen.
Use this function to set the power
indicator on the front side of the monitor to
ON or OFF.
POWER
INDICATOR
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
MENU : Exit
: Adjust
: Adjust
A function that a user can turn on1, on2 or off
the sound when the monitor is powered off or
on or the menu button is touched.
SOUND
SET : Select another
sub-menu
4:3 IN WIDE
To select the image size of the screen.
WIDE
4:3
4:3 : Depending on the input video signal ratio,
it is automatically changed to an optimized
screen ratio. (The 1280X1024 input signal is
changed to 5:4 ratio and 1024X768 to 4:3.)
Resolution
Screen ratio
4 : 3
1600x1200
1280x1024
1152x864
1024x768
800x600
5 : 4
4 : 3
4 : 3
The input signal which the 4:3 IN WIDE does not
support '4:3' is the following.
4 : 3
640x480
4 : 3
-
The 26 inch monitor is 720x400,1280x768,1360x768,
720x480
3 : 2
1440x900,1680x1050,1920x1200
.
Restore all factory default settings except
FACTORY
RESET
"LANGUAGE."
Touch the
button to reset immediately.
If this does not improve the screen image, restore the factory default settings. If necessary, perform the
white balance function again. This function will be enabled only when the input signal is an analog signal.
A16
Download from Www.Somanuals.com. All Manuals Search And Download.
On Screen Display(OSD) Selection and Adjustment
The OSD screen will appear when you touch the
on the front of the monitor.
Menu Name
button
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when applied Screen when not applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear on the left side, whereas the non-applied
screen will appear on the right side. Touch the SET
button to use the adjusted screen.
Main menu
Sub menu
Description
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE
TEXT
MOVIE: For animation images in videos or movies
MENU : Exit
TEXT: For text images (Word processing etc.)
,
: Move
SET : Select
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment.
...
(Brightness): Adjusts screen brightness.
To adjust the USER sub-menu
function, touch the SET Button
...
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
Not applied
Weak clarity and luminosity contrast.
Strong clarity and luminosity contrast.
...
RCM(Real Color Management): Selects the color mode.
2
0
Flesh tone
Not applied
1
3
Color Enhance
Green enhance
SAVE
Select the
sub-menu using the SET button
MENU : Exit
and save the YES value using the buttons.
: Decrease
: Increase
SET : Select another sub-menu
NORMAL
This is under normal operating conditions.
A17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power indicator
• Touch the Power button.
light on?
•
•
Adjust the brightness and the contrast.
G Is the power on and the
power indicator blue or
green?
G Is the power indicator
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
amber?
• Try to turn on the PC
.
•
•
This message appears when the signal from the
G Do you see an "OUT OF
RANGE" message on
the screen?
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
G Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
G
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message
“OSD UNLOCKED” will appear.
A18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Display image is incorrect
G Display Position is
•
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
incorrect.
•
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
G On the screen
background, vertical
bars or stripes are
visible.
•
•
Touch the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
G Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Important
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter
problems such as blurred letters, blurry screen, cut-off screen display or tilted
screen.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer
.
A19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
G The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Have you installed the display driver?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
G
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Display
26 inches (64.868cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
26 inches viewable
0.2865 mm pixel pitch
Horizontal Freq.
Vertical Freq.
30 - 83 kHz (Automatic)
56 - 75 Hz (Automatic)
Sync Input
Video Input
Input Form
Separate Sync.
SOG (Sync On Green)
Digital(HDCP)
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max
VESA 1920 x 1200 @60 Hz
VESA 1920 x 1200 @60 Hz
Resolution
Plug&Play
Recommend
DDC 2B
:
≤
≤
110W(Typ.),130W(USB Full load)
1 W
1 W
Power
Consumption
On Mode
Sleep Mode
Off Mode
With Stand
Without Stand
Dimensions
&Weight
Width
60.19 cm / 23.70 inches
60.19 cm / 23.70 inches
Height 46.32 cm / 18.24 inches(Min) 41.37 cm / 16.29 inches
56.32 cm / 22.17 inches(Max)
Depth 27.02 cm / 10.64 inches
8.10 cm / 3.19 inches
Net
9.9 kg (21.83 lbs)
Tilt
Swivel
Height
-5˚~20˚
350˚
100 mm / 3.94 inches
Range
AC 100-240V~ 50/60Hz 1.2A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
A21
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Stand Base
Power cord
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Standard
USB 2.0, Self-Power
Max 480 Mbps
USB
Data Rate
Power Consumption Max 2.5W x 4
NOTE
Information in this document is subject to change without notice.
A22
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
VGA
VESA
VESA
VGA
VESA
VESA
VESA 1024 x 768
VESA 1024 x 768
VESA 1152 x 864
VESA 1280 x 768
VESA 1280 x 768
VESA 1280 x 1024
VESA 1280 x 1024
VESA 1600 x 1200
VESA 1680 x 1050
VESA 1680 x 1050
VESA 1920 x 1200
640 x 480
640 x 480
720 x 480
720 x 400
800 x 600
800 x 600
59.940
75.000
59.901
70.156
60.317
75.000
60.004
75.029
75.000
59.870
74.893
60.020
75.025
60.000
59.883
60.454
59.950
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
*17
31.469
37.500
35.162
31.500
37.879
46.875
48.363
60.023
67.500
47.776
60.289
63.981
79.976
75.000
64.674
65.290
74.038
*Recommend Mode
Indicator
LED Color
MODE
Blue
Amber
Off
On Mode
Sleep Mode
Off Mode
A23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. After moving the product to face
downward, make sure to place it on
a soft cloth or a cushion to avoid
surface damage.
2. Separate the head and the stand
with the use of a screwdriver.
3. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate
is purchased.
Kensington Security Slot
Connected to a locking
cable that can be purchased
separately at most
computer stores.
A24
Download from Www.Somanuals.com. All Manuals Search And Download.
Digitally yours
Download from Www.Somanuals.com. All Manuals Search And Download.
|