LG Electronics Car Video System E1941S User Manual

OWNER’S MANUAL  
LCD MONITOR  
Please read this manual carefully before operating your set and  
retain it for future reference.  
LCD MONITOR MODEL  
E
E
1941T  
2041T  
E1941S  
E2041S  
E2241S  
E2241T  
2341T  
2441T  
2541T  
E
E
E
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place the  
display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,  
laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release  
of heat generated during operation. If these openings are blocked, built-up heat  
can cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
Leaving a fixed image on the screen for a long time may cause damage to the  
screen and cause image burn-in. Make sure to use a screen saver on the product.  
Burn-in and related problems are not covered by the warranty on this product.  
Do not shock or scratch the front and sides of the screen with metallic objects.  
Otherwise, it may cause damage to the screen.  
Make sure the panel faces forward and hold it with both hands to move. If you  
drop the product, the damaged product can cause electric shock or fire. Contact  
an authorized the service center for repair.  
Avoid high temperatures and humidity.  
For displays with glossy bezels the user should consider the placement of the  
display as the bezel may cause disturbing reflections from surrounding light and  
bright surfaces.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Precautions  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
When cleaning the product, unplug the power cord and scrub gently with a soft  
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other  
liquids directly onto the product. An electric shock may occur. (Do not use  
chemicals such as benzene, paint thinners or alcohol)  
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;  
wipe in one direction only. Too much moisture may cause staining.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
!!! Thank for selecting LGE products !!!  
Please make sure the following items are included with your  
monitor. If any items are missing, contact your dealer.  
Power Cord  
User's Guide/Cards  
15-pin D-Sub Signal Cable  
(To set it up, this signal cable may be  
attached to this product before  
shipping out.)  
DVI-D Signal Cable  
(Only E1941T/E2041T/E2241T/  
E2341T/E2441T/E2541T)  
(This feature is not available in all  
countries.)  
NOTE  
This accessories may look different from those shown here.  
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite  
cores to maintain standard compliance for the product.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand  
1. Place the monitor with its front facing downward on  
a soft cloth.  
2. Assemble the Stand Body into the  
3. Assemble the Stand Base(Front,  
Rear) into the Stand Body in the  
correct direction.  
product in the correct direction as shown in  
the picture. Make sure you push it until you  
hear it “click”.  
Hinge Body  
Stand Body  
Stand Body  
Stand Base  
4. Use a coin on the back of the stand base and turn the screw clockwise to tighten.  
5. Once assembled take the monitor up carefully and face the front side  
.
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Disassembling the stand  
2. Place the monitor face Down on the  
1. Put a cushion or soft cloth on aflat  
cushion or soft cloth.  
surface.  
3.Remove the Stand Body and  
Stand Base from product in  
correct direction as shown in the  
4. Use a coin on the back of the Stand  
Base and turn the screw anticlock-  
wise to loosen  
.
picture  
.
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor,  
the computer system, and other attached devices is turned off.  
Positioning your display  
-After installation, adjust the angle as shown below.  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -5˚ to 15˚  
Do not touch or press the screen when  
adjusting the angle of the monitor.  
When adjusting the angle of the screen, do  
not put your finger(s) in between the head of  
the monitor and the stand body. You can  
hurt your finger(s).  
ERGONOMIC  
It is recommended that in order to maintain an ergonomic and comfortable viewing position,  
the forward tilt angle of the monitor should not exceed 5 degrees.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
E1941T/E2041T/E2241T/E2341T/E2441T/E2541T  
Connecting with the PC  
1. Before setting up the monitor, ensure that the power to the monitor, the computer  
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd  
in order, then tighten the screw  
1
2
of the signal cable.  
A
Connect DVI-D(Digital signal) Cable  
B
Connect D-sub(Analog signal) Cable  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as shown.  
When using a D-Sub signal input cable connector  
for Macintosh  
Mac adapter :For Apple Macintosh use, a  
separate plug adapter is needed to change the  
15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
Varies according to model.  
Connect the signal  
input cable and tighten  
it up by turning in the  
direction of the arrow  
as shown in the figure.  
Wall-outlet type  
3. Press the power button on the front panel to turn the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is executed automatically.  
(Only Analog Mode)  
Power Button  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display  
settings.When the user connects the monitor for the first time, this function automatically adjusts  
the display to optimal settings for individual input signals.  
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen  
flicker or tilted screen while using the device or after changing screen resolution, press the  
AUTO function button to improve resolution.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Display  
E1941S/E2041S/E2241S  
Connecting with the PC  
1. Before setting up the monitor, ensure that the power to the monitor, the computer  
2. sCyosntenmec, tasnidgnoathleinrpautttaccahbedledeviceasnids ptuorwneedr ocoff.rd  
in order, then tighten the screw  
1
2
of the signal cable.  
A
Connect D-sub(Analog signal) Cable  
NOTE  
This is a simplified representation of the rear view.  
This rear view represents a general model; your display may differ from the view as shown.  
When using a D-Sub signal input cable connector for  
Macintosh  
Mac adapter :For Apple Macintosh use, a  
separate plug adapter is needed to change the  
15 pin high density (3 row) D-sub VGA  
connector on the supplied cable to a 15 pin 2  
row connector.  
Varies according to model.  
Connect the signal  
input cable and tighten  
it up by turning in the  
direction of the arrow  
as shown in the figure.  
Wall-outlet type  
3. Press the power button on the front panel to turn the power on. When monitor power is  
turned on, the 'Self Image Setting Function' is executed automatically.  
Power Button  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display  
settings.When the user connects the monitor for the first time, this function automatically adjusts  
the display to optimal settings for individual input signals.  
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen  
flicker or tilted screen while using the device or after changing screen resolution, press the  
AUTO function button to improve resolution.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Front Panel Controls  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Control Panel Functions  
Use this button to enter SUPER ENERGY SAVING  
menu.For more information, refer to page 16.  
SUPER ENERGY  
SAVING Button  
AUTO Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press the  
AUTO button on the MONITOR SETUP OSD. (Only  
Analog Mode)  
This will automatically adjust your display image to the  
ideal settings for the current screen resolution size  
(display mode).  
The best display mode is  
E1941T/E1941S : 1366 x 768  
E2041T/E2041S : 1600 x 900  
E2241T/E2241S/E2341T/E2441T/E2541T: 1920 x 1080  
When two input signals are connected, you can select the  
input signal (D-SUB/DVI) you want. When only one signal is  
connected, it is automatically detected. The default setting  
is D-Sub.  
INPUT Button  
(SOURCE Hot key)  
(Only  
E1941T/E2041T/E2241T/E2341T/E2441T/E2541T  
)
EXIT Button  
Exit the OSD(On Screen Display).  
Use this button to turn the display on or off.  
Power Button &  
Power Indicator  
The power indicator stays blue if the display is running  
properly (On Mode). If the display is in Sleep Mode , the  
power indicator is blinking blue.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating  
parameters of the display is quick and easy with the On Screen  
Display Control system.  
A short example is given below to familiarize you with the use of the  
controls. The following section is an outline of the available  
adjustments and selections you can make using the OSD.  
To make adjustments in the On Screen Display, follow these steps:  
Press the discretionary Button, then the main menu of the OSD appears.  
1
To access a control, use the corresponding Buttons.  
2
Use the  
Use the  
/
/
Buttons to adjust the image to the desired level.  
3
4
Button to select other sub-menu items.  
Press the EXIT Button to exit from the OSD.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
DSUB : D-SUB(Analog signal) input  
DVI-D : DVI-D(Digital signal) input  
Main menu  
Sub-menu  
BRIGHTNESS  
Supported input  
Description  
To adjust the brightness of the  
screen  
MENU  
DSUB  
DVI-D  
To adjust the image size  
ORIGINAL RATIO  
To customize the color of the  
screen  
COLOR TEMP  
(PRESET / USER)  
To adjust the contrast of the  
screen  
CONTRAST  
LANGUAGE  
To customize the screen status  
for a user's operating  
environment  
FACTORY RESET  
DSUB  
DVI-D  
SUPER  
Turn on the SUPER ENERGY  
SAVING function.  
ON  
ENERGY  
SAVING  
Turn off the SUPER ENERGY  
SAVING function.  
OFF  
Initialize the SUPER ENERGY  
SAVING and set to "OFF" mode.  
RESET  
NOTE  
The order of icons may differ depending on the model (13~18).  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
To adjust the brightness of the screen.  
WIDE  
Switch to full screen mode according to  
input image signal.  
ORIGINAL  
Change the input image signal ratio to  
original.  
* This function works only if input  
resolution is lower than monitor ratio  
(16:9).  
Select the screen color.  
PRESET  
•WARM : Set the screen to warm color  
temperature .  
• MEDIUM: Set the screen to medium  
color temperature.  
• COOL: Set the screen to cool color  
temperature.  
USER  
RED  
Set your own red color levels.  
GREEN  
Set your own green color levels.  
BLUE  
Exit : Exit  
Set your own blue color levels.  
,
,
: Move  
: Select another sub-menu  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Description  
To adjust the contrast of the screen.  
To choose the language in which the  
control names are displayed.  
Restore all factory default settings except  
"LANGUAGE."  
Press the  
immediately.  
,
buttons to reset  
Exit : Exit  
,
,
: Move  
: Select another sub-menu  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the SUPER ENERGY SAVING Button, then the main menu of the  
OSD appears.  
Menu Name  
Sub-menus  
Icons  
Exit  
Button  
Move  
Tip  
Restart to select sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
Turn on the SUPER ENERGY  
SAVING fuction.  
ON  
When current setting value is  
ON,the SUPER SAVING color is  
green.  
OFF  
Turn off the SUPER ENERGY  
SAVING function.Now the monitor  
is LED SAVING function.  
When current setting value is  
OFF,the SUPER SAVING color is  
gray.  
Clear the TOTAL POWER  
REDUCTION and TOTAL CO2  
REDUCTION values.  
RESET  
Exit : Exit  
,
: Move  
: Select another sub-menu  
OK : Select  
TOTAL POWER REDUCTION : How much power is saved during using the monitor.  
TOTAL CO2 REDUCTION : Change the TOTAL POWER REDUCTION to CO2.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
On Screen Display(OSD) Selection and Adjustment  
NOTE  
SAVING DATA(W/h):  
25 inch  
19 inch 20 inch 22 inch 23 inch 24 inch  
5
3
3
3
4
5
5
SUPER SAVING  
LED SAVING  
12  
18  
15  
12  
17  
Saving Data depends on the Panel. So,those values should be different from  
each panel and panel vendor.  
LG accumulate those values using integrated function with 10 minutes  
broadcast video signal.  
LED Saving means that how much power can be saved using WLED Panel  
instead of CCFL panel.  
SUPER Saving means that how much power can be more saved using  
SUPER ENERGY SAVING function.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power indicator  
Press the Power button.  
light on?  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
flickering?  
Try to turn on the PC  
.
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
This message appears when the signal from the  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see “OSD  
LOCKED” when you  
push MENU button?  
You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
“OSD UNLOCKED” will appear.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO button to automatically adjust  
incorrect.  
your display image to the ideal setting.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO button to automatically adjust  
your display image to the ideal setting.  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
portrayed.  
IMPORTANT  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
If the recommended resolution (optimal resolution) is not selected, letters may be  
blurred and the screen may be dimmed, truncated or biased. Make sure to select  
the recommend resolution.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Display image is incorrect  
G The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
G The screen blinks.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Do you see an "Unrecognized monitor, Plug&Play (VESA  
DDC) monitor found" message?  
G
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E1941T  
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 47.0 cm  
0
.300 mm x 0.300 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 61 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1366 x 768 @ 60 Hz  
VESA 1366 x 768 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
18 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 44.3 cm ( 17.44 inch )  
Height 35.0 cm ( 13.78 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 44.3 cm ( 17.44 inch )  
Height 28.5 cm ( 11.22 inch )  
Depth 5.5 cm ( 2.16 inch )  
Weight(excl. packing)  
2.4 kg ( 5.29 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 0.8 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E1941S  
47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 47.0 cm  
0
.300 mm x 0.300 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 61 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1366 x 768 @ 60 Hz  
VESA 1366 x 768 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B  
:
<
<
18 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 44.3 cm ( 17.44 inch )  
Height 35.0 cm ( 13.78 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 44.3 cm ( 17.44 inch )  
Height 28.5 cm ( 11.22 inch )  
Depth 5.5 cm ( 2.16 inch )  
Weight(excl. packing)  
2.4 kg ( 5.29 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 0.8 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2041T  
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 50.8 cm  
0
.2766 mm x 0  
.2766 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
Sync Input  
Video Input  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1600 x 900 @ 60 Hz  
VESA 1600 x 900 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
20 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 47.6 cm ( 18.74 inch )  
Height 36.4 cm ( 14.33 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 47.6 cm ( 18.74 inch )  
Height 30.3 cm ( 11.92 inch )  
Depth 5.7 cm ( 2.24 inch )  
Weight(excl. packing)  
2.7 kg ( 5.95 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2041S  
50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 50.8 cm  
0
.
2766 mm x 0  
.
2766 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1600 x 900 @ 60 Hz  
VESA 1600 x 900 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B  
:
<
<
20 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 47.6 cm ( 18.74 inch )  
Height 36.4 cm ( 14.33 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 47.6 cm ( 18.74 inch )  
Height 30.3 cm ( 11.92 inch )  
Depth 5.7 cm ( 2.24 inch )  
Weight(excl. packing)  
2.7 kg ( 5.95 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2241T  
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 54.6 cm  
0
.248 mm x 0.248 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
VESA 1920 x 1080 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
24 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 50.9 cm ( 19.80 inch )  
Height 38.8 cm ( 15.27 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 50.9 cm ( 19.80 inch )  
Height 32.2 cm ( 12.67 inch )  
Depth 5.8 cm ( 2.28 inch )  
Weight(excl. packing)  
2.9 kg (6.39 lb)  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2241S  
54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 54.6 cm  
0
.248 mm x 0.248 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Signal Input  
Input Form  
15 pin D-Sub Connector  
RGB Analog (0.7 Vp-p/ 75 ohm)  
Max  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
VESA 1920 x 1080 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B  
:
<
<
24 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 50.9 cm ( 19.80 inch )  
Height 38.8 cm ( 15.27 inch )  
Depth 16.6 cm ( 6.54 inch )  
Width 50.9 cm ( 19.80 inch )  
Height 32.2 cm ( 12.67 inch )  
Depth 5.8 cm ( 2.28 inch )  
Weight(excl. packing)  
2.9 kg ( 6.39 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2341T  
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 58.4 cm  
0
.265 mm x 0.265 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
VESA 1920 x 1080 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
28 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 54.6 cm ( 21.49 inch )  
Height 40.7 cm ( 16.02 inch )  
Depth 17.9 cm ( 7.04 inch )  
Width 54.6 cm ( 21.49 inch )  
Height 34.2 cm ( 13.46 inch )  
Depth 5.7 cm ( 2.24 inch )  
Weight(excl. packing)  
3.4 kg ( 7.49 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.0 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2441T  
60.97 cm (24 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 60.97 cm  
0
.277 mm x 0.277 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
VESA 1920 x 1080 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
25 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 56.9 cm ( 22.40 inch )  
Height 41.9 cm ( 16.49 inch )  
Depth 17.9 cm ( 7.04 inch )  
Width 56.9 cm ( 22.40 inch )  
Height 35.4 cm ( 13.93 inch )  
Depth 5.9 cm ( 2.32 inch )  
Weight(excl. packing)  
4.0 kg ( 8.81 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.2 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2541T  
63.44 cm (25 inch) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
Display  
Visible diagonal size : 63.44 cm  
0.288 mm x 0.288 mm (Pixel pitch)  
Horizontal Freq.  
Vertical Freq.  
Input Form  
30 kHz to 83 kHz (Automatic)  
56 Hz to 75 Hz (Automatic)  
Separate Sync.  
Sync Input  
Video Input  
Digital  
Signal Input  
Input Form  
15 pin D-Sub Connector  
DVI-D Connector (Digital)  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Max  
Recommend  
VESA 1920 x 1080 @ 60 Hz  
VESA 1920 x 1080 @ 60 Hz  
Resolution  
Plug&Play  
DDC 2B(Analog,Digital)  
:
<
<
33 W(Typ.)  
0.3 W  
0.3 W  
On Mode  
Power  
Consumption  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
& Weight  
Width 59.4 cm ( 23.38 inch )  
Height 43.4 cm ( 17.08 inch )  
Depth 17.9 cm ( 7.04 inch )  
Width 59.4 cm ( 23.38 inch )  
Height 37.1 cm ( 14.60 inch )  
Depth 6.1 cm ( 2.40 inch )  
Weight(excl. packing)  
4.4 kg ( 9.70 lb )  
Tilt : -5˚ to 15˚  
Range  
AC 100-240 V~ 50 / 60 Hz 1.2 A  
Power Input  
Operating Conditions  
Environment  
al Conditions  
Temperature  
Humidity  
10 ˚C to 35 ˚C  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature  
Humidity  
-20 ˚C to 60 ˚C  
5 % to 90 % non-Condensing  
Stand Base  
Attached ( ), Detached ( O )  
Wall-outlet type  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Preset Modes (Resolution)  
E1941T/E1941S  
*If you can't select 1366 x 768 in display property timing option, please  
update your video card driver from your video card vendor.  
Polarity(H/V)  
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
49.725  
48.363  
47.712  
-/+  
-/-  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1366 x 768  
70  
60  
75  
60  
75  
75  
60  
60  
3
-/-  
4
+/+  
+/+  
-/-  
-/-  
+/+  
5
6
7
*8  
*Recommend Mode  
E2041T/E2041S  
Display Modes (Resolution)  
Horizontal Freq. (kHz) Vertical Freq. (Hz)  
Polarity(H/V)  
-/+  
-/-  
1
2
31.468  
70  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1600 x 900  
31.469  
60  
-/-  
3
37.500  
75  
+/+  
+/+  
-/-  
+/+  
+/+  
+/+  
4
37.879  
60  
5
46.875  
75  
6
48.363  
60  
7
60.123  
75  
8
67.500  
75  
*9  
60.000  
60  
*Recommend Mode  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
E2241T/E2241S/E2341T/E2441T/E2541T  
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)  
Polarity(H/V)  
-/+  
-/-  
1
2
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
65.290  
67.500  
720 x 400  
640 x 480  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
-/-  
3
640 x 480  
+/+  
+/+  
-/-  
+/+  
+/+  
+/+  
+/+  
-/+  
+/+  
4
800 x 600  
800 x 600  
5
6
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1920 x 1080  
7
8
9
10  
11  
*12  
*Recommend Mode  
Indicator  
LED Color  
MODE  
Blue  
Blue Blinking  
Off  
On Mode  
Sleep Mode  
Off Mode  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Remove the Stand Body and Stand Base from product in correct direction as shown in  
the picture  
.
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Wall mount plate  
3. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or wall mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more  
details, which is provided when Wall mount  
plate is purchased.  
Kensington Security Slot  
<Screw Mounting Interface Dimension>  
Hole spacing : 75 mm x 75 mm.  
Connected to a locking cable that can  
be purchased separately at most  
computer stores.  
NOTE  
VESA compatible only with respect to screw mounting interface dimensions and mounting screw  
specifications  
Please use VESA standard as below.  
* 784.8 mm and under (30.9 inch)  
- Wall Mount Pad Thickness : 2.6 mm  
- Screw : 4.0 mm x Pitch 0.7 mm x Length 10 mm  
* 787.4 mm and above (31.0 inch)  
- Please use VESA standard wall mount pad and screws.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Make sure to read the Safety Precautions  
before using the product.  
Keep the OWNER’S MANUAL(CD) in an  
accessible place for furture reference.  
The model and serial number of the SET is  
located on the back or one side of the SET.  
Record it below should you ever need service.  
ENERGY STAR is a set of power-saving  
guidelines issued by the U.S.Environmental  
Protection Agency(EPA).  
MODEL  
SERIAL  
As an ENERGY STAR Partner LGE U. S. A.,Inc.  
has determined that this product meets the  
ENERGY STAR guidelines for energy efficiency.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Network Card Big Disk Network User Manual
Land Pride Brush Cutter RCR3510 User Manual
Laser Handheld TV DVBT C30 User Manual
Lathem Clock AT MSX User Manual
Leica Digital Camera SP2600 User Manual
Lincoln Electric Welder IM10043 A User Manual
Linksys Network Router E 4200 User Manual
Marshall electronic Computer Monitor V R151DP AFHD User Manual
Masterbuilt Fryer 20010106 User Manual
Mattel Video Game Controller P5959 User Manual