LG
LG
Window-Type Air Conditioner
OWNER'S MANUAL
MODELS, MODELOS:
WK Series: LW7000ER
LW8000ER
WL Series: L1004R
IMPORTANT
LW1000ER
Please read through this manual. It contains valuable
information about your air conditioner. This manual may
help save time and money by explaining proper air
conditioner maintenance and preventing improper use.
L1204R
LW1200ER
L1404R
LB1000ER
LB1200ER
PRECAUTIONS
Pay close attention to precautions in order to prevent
potential hazards and damage from misuse or improper
installation. LG is not responsible for any damages
caused by misuse of the air conditioner.
WP Series: LW1400ER
L1504R
LW1500ER
L1804R
LW1800ER
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Precautions
Precautions
To prevent injury to the user or other people and property damage, the following instructions must
be followed.
■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
This symbol indicates the possibility of death or serious injury.
WARNING
This symbol indicates the possibility of injury or damage to properties only.
CAUTION
■ Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
WARNING
■ Installation
Always install the expansion panel(s).
Do not place the power cord near a heater.
• No installation may cause fire and electric
shock accident.
• It may cause fire and electric shock.
Do not use the power cord near flammable
gas or combustibles such as gasoline,
benzene, thinner, etc.
Do not disassemble or modify products.
• It may cause explosion or fire.
• It may cause failure and electric shock.
Gasolin
3
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Operation
Plug in the power plug
properly.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an
unspecified power cord.
• Otherwise, it will cause
electric shock or fire due to
heat generation or electric
shock.
• It will cause electric shock or
fire due to heat generation.
• It will cause electric shock or
fire.
ON
Do not modify power cord
length.
Do not share the outlet with
other appliances.
Always plug into a
grounded outlet.
• It will cause electric shock or
fire due to heat generation.
• It will cause electric shock or
fire due to heat generation.
• No grounding may cause
electric shock (See
Installation Manual).
Unplug the unit if strange
sounds, odors, or smoke
come from it.
Do not use the socket if it is
loose or damaged.
Do not operate with wet
hands or in damp
environment.
• Otherwise it may cause fire
and electric shock accident.
• It may cause fire and electric
shock.
• It will cause electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not allow water to run
into electric parts.
Leave the door closed while
the air conditioner is
running.
Ventilate before operating
air conditioner when gas
goes out.
• It will cause failure of machine • It is not designed to cool the
• It may cause explosion, fire,
and burn.
or electric shock.
entire house.
CAUTION
■ Installation
Never touch the metal parts
of the unit when removing
the filter.
Do not block the inlet or
outlet.
Ensure that the outer case
is not damaged by age or
wear.
• They are sharp and may
cause injury.
• It may cause failure of
appliance or accident.
• If leaving appliance damaged,
there is concern of damage
due to the falling of product.
■ Operation
Be cautious not to touch the
sharp edges when
installing.
Hold the plug by the head
when taking it out.
Turn off the main power
switch when not using it for
a long time.
• It may cause injury.
• It may cause electric shock
and damage.
• Prevent accidental startup
and the possibility of injury.
Sharp
edges
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not place heavy object
on the power cord and take
care so that the cord should
not be pressed.
If water enters the product,
turn off the the power switch
of the main body of appliance.
Contact service center after
taking the power-plug out
from the socket.
Do not clean the air
conditioner with water.
• There is danger of fire or
electric shock.
• Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Turn off the power and
breaker firstly when
cleansing the unit.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not use this appliance
for special purposes such
as pets, foods, precision
machinery, or objects of art.
• Since the fan rotates at high
speed during operation, it
may cause injury.
• This could injure the pet or
plant.
• It is an air conditioner, not a
precision refrigeration system.
Always insert the filter
securely.
Clean it every two weeks.
Use a soft cloth to clean. Do
not use wax, thinner, or a
strong detergent.
Do not drink water drained
from air conditioner. / Do
not direct airflow at room
occupants only.
• Operation without filters will
cause failure.
• The appearance of the air
conditioner may deteriorate,
change color, or develop
surface flaws.
• It contains containments and
will make you sick. / This
could damage your health.
x
Thinner
Wa
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Prior to Operation
Precautions
Preparing for operation
1
2
3
4
5
6
Contact an installation specialist for installation.
Plug in the power plug properly.
Do not share the same outlet with other appliances
Do not use an extension cord.
Do not start/stop operation by plugging/unplugging the power cord.
If cord/plug is damaged, replace only with an authorized part.
Usage
1
2
3
Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not
expose occupants, pets, or plants to direct airflow for extended periods of time.
Due to the possibility of oxygen deficiency, ventilate the room when using together with stoves or other
heating devices.
Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices,
food, pets, plants, and art objects). Usage in such a manner could harm such property.
Cleaning and maintenance
1
2
3
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp
metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading
to possible electric shock.
When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a
very high speed during operation. There is a possibility of injury if the unit’s power is accidentally
triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Remote Control Operations
Instructions
The remote control and control panel will look like those represented in the following pictures.
6
COOL FAN DRY
AIR
PURIFIER
Air
Purifier
FAN
Power
ENERGY
SAVER
7
8
1
AIR
INDOOR
DESIRED
PURIFIER
Temp
CLEAN
FILTER
2
4
3
5
Fan Speed
FAN
SPEED
AIR
PURIFIER
TIMER
MODE
TEMP
POWER
Sleep
Timer
Mode
Auto
Swing
5
4
3
7
2
1
Power
˚F
Cool
F1 LOW
F2 MED
1
2
F3 HIGH
6
2
Energy
Saver
Temp
Fan
Dry
Timer
Fan Speed
4
3
Timer
Mode
5
3
5
4
1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Operations
7
1
POWER
AIR PURIFIER
Operation starts when this button is pressed and
stops when you press the button again.
• Press the Air Purifier button. Operation will start
when the button is pressed and stop when the
button is pressed again.
2
TEMPERATURE CONTROL
The thermostat monitors room temperature to
maintain the desired temperature.
The thermostat can be set between 60°F~86°F
(16°C~30°C).
The unit takes an average of 30 minutes to adjust the
room temperature by 1°F.
• Set the fan speed again with the remote control.
You can select the fan speed in three steps-high,
low or medium.
Each time the button is pressed, the fan speed
mode is shifted.
• If you press the only Air Purifier button, only air
purifying operates without cooling.
Then, fan speed is low.
You can select the fan speed in three steps; high,
low, or medium.
3
OPERATION MODE SELECTOR
Select cooling mode to cool the room.
Select energy saver mode for energy saving
operation.
Select fan mode for basic ventilating fan operation.
Select dry mode for dry operation.
Each time the fan speed button is pressed, the fan
speed mode is shifted.
4
5
FAN SPEED SELECTOR
For increased power while cooling, select a higher
fan speed.
8
SLEEP MODE
• Press the sleep mode button to set the time you
want the unit to turn off automatically.
3 steps: High ■ Low ■ Med
• Every time you push this button, the remaining time
will be set as follows. (1Hour ■ 2Hours ■ 3Hours ■
4Hours ■ 5Hours ■ 6Hours ■ 7Hours ■ 0Hours ■
1Hour ■ 2Hours ■ ...)
ON/OFF TIMER
The timer can be set to start and stop the unit in
hourly increments (up to 12 hours).
6
REMOTE CONTROL SENSOR
: CLEAN FILTER
NOTICE
You can see "CLEAN FILTER" display after 1000 hours that it is the time of cleaning filter when
operating in Air purifier.
AUTO RESTART
In failure of electric power, the unit runs as previous setting operation.
Inserting the Remote Control Batteries
1
Push out the cover on the back of the remote control with your thumb
Pay attention to polarity and insert two new AAA 1.5V batteries.
Reattach the cover.
2
3
: Do not use rechargeable batteries. Make sure that both batteries are new.
NOTICE
•
In order to prevent discharge, remove the batteries from the remote control if the air conditioner is not going to be
used for an extended period of time
Keep the remote control away from extremely hot or humid places.
To maintain optimal operation of the remote control, the remote sensor should not be exposed to direct sunlight.
• The remote control can be mounted on a wall using the mountable holder.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Adjusting the Air Flow Direction
Instructions
Vent Control
For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.
OPEN the vent to discharge stale air.
Part
A
CLOSE
VENT
OPEN
: Before using the ventilation feature, position
the vent lever by pulling Part A out straight
and snapping it into place.
NOTICE
Adjusting the Air Flow Direction
Airflow can be adjusted by changing the direction of the air conditioner's louvers. This can also increase the
cooling efficiency of the air conditioner.
• Adjusting Horizontal Air Flow Direction
Adjusting the vertical louvers left and right will
change horizontal airflow.
• Adjusting Vertical Air Flow Direction
Adjusting the horizontal vane up and down will
change vertical airflow. The vane can be adjusted
by nudging the vane backward or forward.
Adjusting horizontal air flow
Adjusting vertical air flow
• Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and
Care and Maintenance
Maintenance
Turn the power off and unplug the power plug before cleaning the air conditioner.
Air Filter
The air filter behind the inlet grille should be checked and cleaned at least once every 2 weeks (or as
necessary) to maintain optimal performance of the air conditioner.
How to remove the air filter
1
2
3
4
5
The grille may be opened from the top for easy
maintenance after installation.
Open the inlet grille by pulling off the exposed door
on the top of the unit (based on installation).
Pull the tab slightly to release the filter. Pull the filter
in the same direction as the opening.
Clean the filter with warm, soapy water. The water
should be below 40°C (104°F).
Rinse off and gently shake off excess water from the
filter. Let it dry before replaceing it.
Drainage
The base pan may overflow due to high humidity. To drain the excess
water, remove the drain cap from the back of the unit and secure the
drainpipe.
When pressing the drainpipe into place, apply force in the direction
away from the fins to avoid injuring yourself.
Drain pipe
Drain cap
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Contro Opera
s
Air Purifying Filter (Optional)
The Air Purifying filter behind the air filter should be checked and cleaned once every 3 months or more often if
necessary.
1
After removing the Air Purifying Filter, pull
slightly forward to remove the Air Purifying filter.
2
Soak the Air Purifying Filter in water mixed with a
mild detergent for 20~30 minutes.
3
Dry the Air Purifying Filter in the shade for a
day.(The moisture must be removed completely
on this part.)
4
5
Note the cuts of electric discharge lines.
Re-install the Air Purifying Filter to the original
position.
WARNING: Don't touch this Air Purifying Filter within 10
seconds after opening the inlet grille;
it may cause an electric shock.least 3 minutes before resetting
to the cooling operation again.
Remote Control Operations
How to Attach Drain Pan (Optional)
The air conditioner employs a proper drain method whereby the condensed water (moisture removed from the
air) is drained to the outside.
In very humid weather, (and for reverse cycle models in the reverse mode) excessive condensate water removed
from the air may cause some water to collect. To remove this excess water you can install the drain pan as
detailed below.
1
Take the drain pan which is located in the air
discharge.
CABINET
2
Remove the hole rubber from the base-pan (for
some models).
DRAIN
PAN
3
4
Install the drain pan to the right corner of the
cabinet with 4 (or 2) screws.
SCREW
DRAIN HOSE
Connect the drain hose of 3/5" inside diameter to
the outlet located at the bottom of the drain
pan.You can purchase the drain hose or tubing
locally to satisfy your particular needs. (Drain
hose is not supplied).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Hardware Installation
Installation
Product Features
CAUTION: This appliance should be installed in accordance with national wiring
regulations. The following information serves acts as a guide to help to explain product
features.
13
6
5
7
17
11
8
1
14
12
9
2
3
4
15
10
16
1. CABINET
2. FRONT GRILLE
9. CONTROL PANEL
10. POWER CORD
3. AIR FILTER
4. AIR INTAKE (INLET GRILLE)
5. AIR DISCHARGE
11. COMPRESSOR
12. BASE PAN
13. BRACE
6. VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
7. EVAPORATOR
8. HORIZONTAL AIR DEFLECTOR
(VERTICAL LOUVER)
14. CONDENSER
15. REMOTE CONTROLLER
16. AIR PURIFYING FILTER (Optional)
17. CASE, FILTER (Optional)
Installing the Power cord
You can choose between two methods below according to your window stool shape and preference.
Using slit "A"
Using slit "B"
• Fasten the stopper using 2 screw holes, and lead
• Fasten the stopper using left screw hole, and rotate
out the power cord through slit "A".
properly to lead the power cord out through slit "B".
A
B
Power cord
Power cord
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WK Series
How to Install the Unit
1
2
3
To prevent vibration and noise, make sure the unit
is installed securely and firmly.
Fence
Awning
Install the unit where the sunlight does not shine
directly on the unit.
Cooled air
Heat
radiation
The outside of the cabinet must extend outward for
at least 12" and there should be no obstacles, such
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
About 1/2"
Over 20"
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the
structure.
4
5
Install the unit a little slanted so the back is slightly lower than the front (about 1/2").
This will force condensed water to flow to the outside.
Install the unit with the bottom about 30"~60" above the floor level.
Window Requirements
: All supporting parts should be secured to firm wood, masonry, or metal.
NOTICE
• This unit is designed for installation in standard double
hung windows with actual opening widths from 25"
to 36".
25" to 36"
15" min
Stool
• The top and bottom window sash must open sufficiently
to allow a clear vertical opening of 15" from the bottom
of the upper sash to the window stool.
(With frame curtain)
Offset
1/2" to 11/4"
Sill
Interior wall
Exterior
20 1/12" min.
(Without frame curtain)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
WL Series
How to Install the Unit
1
2
3
To prevent vibration and noise, make sure the unit
is installed securely and firmly
Fence
Awning
Install the unit where the sunlight does not shine
directly on the unit.
Cooled air
Heat
radiation
The outside of the cabinet must extend outward for
at least 12" and there should be no obstacles, such
as a fence or wall, within 20" from the back of the
cabinet because it will prevent heat radiation of the
condenser.
About 1/2"
Over 20"
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the
structure.
4
5
Install the unit a little slanted so the back is slightly lower than the front (about 1/2").
This will force condensed water to flow to the outside.
Install the unit with the bottom about 30"~60" above the floor level.
Window Requirements
: All supporting parts should be secured to firm wood, masonry, or metal.
NOTICE
• This unit is designed for installation in standard double
hung windows with actual opening widths from 27"
to 39".
27" to 39"
16" min
Stool
• The top and bottom window sash must open sufficiently
to allow a clear vertical opening of 16" from the bottom
of the upper sash to the window stool.
(With frame curtain)
Offset
1/2" to 11/4"
Sill
Exterior
Interior wall
23 5/8" min.
(Without frame curtain)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WP Series
How to Install the Unit
1
2
3
To prevent vibration and noise, make sure the unit
is installed securely and firmly.
Fence
Awning
Install the unit where the sunlight does not shine
directly on the unit.
Cooled air
Heat
radiation
There should be no obstacles, such as a fence and
wall, within 20" from the back of the cabinet
because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
About 1/2"
Over 20"
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the
structure.
4
5
Install the unit a little slanted so the back is slightly lower than the front (about 1/2").
This will force condensed water to flow to the outside.
Install the unit with the bottom about 30"~60" above the floor level.
Window Requirements
: All supporting parts should be secured to firm wood, masonry, or metal.
NOTICE
Sash
• This unit is designed for installation in standard double
hung windows with actual opening widths from 29"
to 41".
29" to 41"
18" min.
• The top and bottom window sash must open sufficiently
to allow a clear vertical opening of 18" from the bottom
of the upper sash to the window stool.
Window
Inner sill
Offset
Sill
Exterior
Interior wall
29" min.
(Without frame curtain)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WK, WL Series
Installation Kits Contents
NO.
1
2
3
4
NAME OF PARTS
FRAME CURTAIN
SILL SUPPORT
BOLT
Q'TY
2
2
2
2
2
3
7
4
8
1
NUT
13
5
6
5
6
7
8
SCREW (TYPE A)
SCREW (TYPE B)
SCREW (TYPE C)
FOAM-STRIP
16
3
5
10
1
12
9
DRAIN PIPE
1
9
11
10
11
12
13
FOAM-PE
1
2
1
1
FRAME GUIDE
WINDOW LOCKING BRACKET
FOAM-PE
Suggested Tool Requirements
SCREWDRIVER(Philips and Flatead), RULER, KNIFE, HAMMER, PENCIL, LEVEL
Shipping
Screws
PREPARATION OF CHASSIS
1
2
3
Remove the screws which fasten the cabinet at both
sides and at the back.
Slide the unit from the cabinet by gripping the base pan
handle and pulling forward while bracing the cabinet.
Cut the window sash seal to the proper length.
Peel off the backing and attach the Foam-PE
underside of the window sash.
to the
4
5
6
7
Remove the backing from the top upper guide Foam-PE
and attach it to the bottom of the Upper Guide.
Attach the upper guide onto the top of the cabinet with 3
Type A screws
.
Upper guide
Insert the Frame Guides
cabinet.
into the bottom of the
13
10
Insert the Frame Curtain
into the Upper Guide and
(Type A)
Frame Guides
.
5
Upper guide
8
Fasten the curtains to the unit with 4 Type
A screws
11
.
5
11
(Type A)
5
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabinet Installation
1
Open the window. Mark a line on center of the
window stool.
Carefully place the cabinet on the window stool and
align the center mark on the bottom front with the
center line marked in the window stool.
Upper Guide
Window Sash
Window stool
Front Angle
Fig. 1
2
Pull the bottom window sash down behind the Upper
Guide until it meets.
Upper guide
: Do not pull the window sash down tightly that
NOTICE
the movement of Frame Curtain
is restricted.
13
Foam-pe
Cabinet
1
Frame Curtain
10
Foam-pe
Fig. 2
3
Loosely assemble the Sill Support
in Fig. 3.
using the parts
INDOOR
OUTDOOR
2
Sill Support
3
4
Bolt
Nut
Fig. 3
4
Select the position that will place the Sill Support
near the outer most point on sill (See Fig. 4)
5
Screw(Type A)
11
Frame Guide
: Be careful when you install the cabinet
NOTICE
(Frame Guides
are broken easily).
Cabinet
OUTDOOR
5
Attach the Sill Support
relation to the selected position using 2 Type A
screws in each support (See Fig. 4).
to the cabinet track hole in
INDOOR
Fig. 4
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6
The cabinet should be installed with a very slight tilt
(about 1/2") downward toward the outside
(See Fig. 5).
6
Screw(Type B)
Adjust the bolt and the nut of Sill Support
balancing the cabinet.
for
2
Sill Support
7
8
Attach the cabinet to the window stool by driving
the screws (Type B: Length 16mm (5/8 inch)
and below.) through the front angle into window
stool.
Sash track
Pull each Frame Curtain
fully to each window
sash track, and repeat step 2.
Front Angle
6
Screw(Type B)
2
Sill Support
Fig. 5
9
Attach each Frame Curtain
the window sash using
screws
(Type C). (See Fig. 6)
7
Type C
CAUTION: Do not drill a hole in the bottom
pan. The unit is designed to operate with
approximately 1/2" of water in bottom pan.
There is no need to add water if the pan is
dry.
Fig. 6
10
Slide the unit into the cabinet. (See Fig. 7)
CAUTION: For security purpose, reinstall
screws (Type A) at cabinet's sides.
Screw(Type A)
Power cord
Screw
(Type A)
Fig. 7
11
Cut the Foam-Strip
to the proper length and insert
between the upper window sash and the lower
window sash. (See Fig. 8)
8
Foam-Strip
Fig. 8
19
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Attach the Window Locking Bracket
C screw . (See Fig. 9)
with a Type
Window locking
12
bracket
Fig. 9
Attach the front grille to the cabinet by inserting the
tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Fig. 10)
13
14
Fig. 10
Pull down the inlet grille and secure it with a Type
A screw
through the front grille. (See Fig. 11)
15 Window installation of room air conditioner is
now completed. See ELECTRICAL DATA for
attaching power cord to electrical outlet.
Fig. 11
20
Download from Www.Somanuals.com. All Manuals Search And Download.
WP Series
Installation Kits Contents
NO.
1
NAME OF PARTS
FRAME CURTAIN
Q'TY
2
1
2
3
4
5
2
3
4
SUPPORT BRACKET
SILL BRACKET
LOCK NUT
2
2
4
6
7
8
9
10
11
5
6
7
8
SCREW (TYPE A)
SCREW (TYPE B)
SCREW (TYPE C)
SCREW (TYPE D)
CARRIAGE BOLT
FOAM STRIP
FOAM SEAL
WINDOW LOCKING BRACKET
DRAIN PIPE
14
7
5
2
2
1
1
1
1
9
10
11
12
13
14
15
15
12
13
14
FOAM-PE
FRAME GUIDE
1
2
Suggested Tool Requirements
SCREWDRIVER(Philips and Flatead), RULER, KNIFE, HAMMER, PENCIL, LEVEL
Shipping
Screws
PREPARATION OF CHASSIS
1
2
3
Remove the screws which fasten the cabinet at both
sides and at the back.
CO
OL
F
A
N
R
H
F
A
O
ID
N
R
DE
SIR
N
E
ER
A
V
GY
ER
U
A
I
R
R
Y
FIE
RE
A
U
T
O
RT
R
ST
A
Slide the unit from the cabinet by gripping the base pan
handle and pulling forward while bracing the cabinet.
Cut the window sash seal to the proper length.
Peel off the backing and attach the Foam-Seal
underside of the window sash.
to the
CO
OL
F
A
N
DR
Y
H
F
A
D
E
IND
OO
N
F
OS
R
T
DE
SIR
ED
NER
S
A
G
VE
R
Y
P
U
A
I
R
R
Y
FIE
RE
ST
AR
A
U
T
O
R
T
4
5
6
7
Remove the backing from the top upper guide Foam-PE
and attach it to the bottom of the Upper Guide.
Attach the upper guide onto the top of the cabinet with 3
Type A screws
.
Upper guide
Insert the Frame Guides
cabinet.
into the bottom of the
11
14
Upper guide
Insert the Frame Curtain
into the Upper Guide and
Frame Guides
.
8
Fasten the curtains to the unit with 10 Type
A screws
.
5
(Type A)
15
(Type A)
5
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabinet Installation
1
Open the window. Mark a line on the center of the
window stool between the side window stop
moldings.
Loosely attach the sill bracket to the support
bracket using the carriage bolt and the lock nut.
Sill
Bracket
3
Support
Bracket
2
Carriage
Bolt
4
Lock nut
9
Fig. 12
Machine screw(Type D)
and lock nut
2
Attach the sill bracket to the window sill using the
screws (Type B).
Carefully place the cabinet on the window stool
and align the center mark on the bottom front with
the center line marked window stool.
Cabinet
Track hole
Outer edge
of window
sill
Support
Bracket
2
6
(Type B)
Carriage bolt
and lock nut
3
Sill bracket
Fig. 13
3
Using the M-screw and the lock nut, attach the
support bracket to the cabinet track hole. Use the first
track hole after the sill bracket on the outer edge of
the window sill. Tighten the carriage bolt and the lock
nut. Be sure the cabinet slants outward.
CAUTION: Do not drill a hole in the bottom
pan. The unit is designed to operate with
approximately 1/2" of water in bottom pan.
Upper
Guide
Window stool
Front angle
Fig. 14
4
Pull the bottom window sash down behind the Top
retainer bar until they meet.
Window sash
Foam
Upper Guide
:1. Do not pull the window sash down so tightly
that the movement of Frame curtain is
restricted.
NOTICE
11
-Seal
Attach the cabinet to the window stool by
driving the screws (Type B) through the
cabinet into window stool.
Cabinet
Frame curtain
14
Foam-PE
2. The cabinet should be installed with a very
slight tilt downward toward the outside.
Fig. 15
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Pull each Frame curtain fully to each window sash
track, and pull the bottom window sash down behind
the Top retainer bar until it meets.
Sash track
Front Angle
6
Screw(Type B)
Fig. 16
6
Attach each Frame curtain the window sash by using
screws (Type C.) (See Fig. 17)
7
(Type C)
Fig. 17
7
Slide the unit into the cabinet.(See Fig. 18)
CO
O
F
A
N
R
Y
E
A
F
A
IN
DO
N
E
R
OR
DE
SI
RE
N
ER
GY
ER
D
S
A
V
P
U
A
I
R
R
Y
U
FIE
A
R
RE
ST
AR
T
O
CAUTION: For security purpose,
reinstall screws(Type A)
at cabinet's sides.
T
Screw
Screw
Power Cord
Fig. 18
8
9
Cut the Foam-strip to the proper length and insert
between the upper window sash and the lower
window sash.(See Fig. 19)
Foam-Strip
Fig. 19
Window locking
bracket
Attach the Window locking bracket with a screw
(Type C.) (See Fig. 20)
Fig. 20
23
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Attach the front grille to the cabinet by inserting the
tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Fig. 21)
11
12
Lift the inlet grille and secure it with a screw (Type A)
through the front grille.(See Fig. 21)
ER
W
PO
P
M
TE
E
D
O
M
F
A
N
S
PE
ED
E
M
TI
Window installation of room air conditioner is now
completed. See ELECTRICAL DATA for attaching
power cord to electrical outlet.
Fig. 21
Electrical Data
Line Cord Plug
Use Wall Receptacle
Power Supply
Do not under any
circumstances cut
or remove the
grounding prong
from the plug.
Use 15 AMP, time
delay fuse or circuit
breaker.
Power supply cord with
3-prong grounding plug
Standard 125V, 3-wire grounding
receptacle rated 15A, 125V AC
Use of extension cords
• Because of potential safety hazards, we strongly discourage the use of an extension cord. However, if you wish
to use an extension cord, use a CSA certified/UL-listed 3-wire (grounding) extension cord, rated at 15A, 125V.
Electrical Data (L1804R, LW1800ER MODELS)
Line Cord Plug
Use Wall Receptacle
230V/208V
Power Supply
Use 15 AMP circuit.
Refer to nameplate for
correct fusing.
tandem type
All wirring should be made in accordance with local electrical codes and regulations.
: Aluminum house wiring may pose special problems.
Consult a qualified electrician.
NOTICE
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Safety
Because of potential safety hazards, we strongly
discourage the use of an adapter plug. However, if you
wish to use an adapter, a TEMPORARY
CONNECTION may be made. Use UL-listed adapter,
available from most local hardware stores (Fig. 23).
The large slot in the adapter must be aligned with the
large slot in the receptacle to assure a proper polarity
connection.
IMPORTANT
(PLEASE READ CAREFULLY)
FOR THE USER'S PERSONAL SAFETY, THIS
APPLIANCE MUST BE PROPERLY GROUNDED
The power cord of this appliance is equipped with a
three-prong (grounding) plug. Use this with a standard
three-slot (grounding) wall power outlet (Fig. 22) to
minimize the hazard of electric shock. The customer
should have the wall receptacle and circuit checked by
a qualified electrician to make sure the receptacle is
properly grounded.
CAUTION: Attaching the adapter ground
terminal to the wall receptacle cover screw
does not ground the appliance unless the cover
screw is metal, and not insulated, and the wall
receptacle is grounded through the house
wiring. The customer should have the circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
PREFERRED METHOD
Disconnect the power cord from the adapter, using one
hand on each. Otherwise, the adapter ground terminal
might break. DO NOT USE the appliance with a
broken adapter plug.
Ensure proper ground
exists before use
Fig. 22
B. SITUATIONS WHEN THE APPLIANCE WILL BE
DISCONNECTED OFTEN.
Do not use an adapter plug in these situations.
Unplugging the power cord frequently can lead to an
eventual breakage of the ground terminal. The wall
power outlet should be replaced by a three-slot
(grounding) outlet instead.
DO NOT CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER PLUG.
A. SITUATIONS WHEN THE APPLIANCE WILL BE
DISCONNECTED OCCASIONALLY:
TEMPORARY METHOD
USE OF EXTENSION CORDS
Adapter plug
Because of potential safety hazards, we strongly
discourage the use of an extension cord. However, if
you wish to use an extension cord, use a CSA
certified/UL-listed 3-wire (grounding) extension cord,
rated at 15A, 125V.
Metal screw
Receptacle cover
Fig. 23
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Safety (L1804R, LW1800ER MODELS)
IMPORTANT
(PLEASE READ CAREFULLY)
FOR THE USER'S PERSONAL SAFETY, THIS
APPLIANCE MUST BE PROPERLY GROUNDED
230, 208, and 230/208 VOLT UNITS
The power cord of this appliance is equipped with a
three-prong (grounding) plug. Use this with a standard
three-slot (grounding) wall power outlet (Fig. 24) to
minimize the hazard of electric shock. The customer
should have the wall receptacle and circuit checked by
a qualified electrician to make sure the receptacle is
properly grounded.
These units are equipped with a three-prong grounding
plug on the power supply cord, which must be plugged
into a matching properly grounded three-prong wall
receptacle for your protection against possible shock
hazard. If such an outlet is not present, one must be
installed by a qualified electrician in accordance with
the National Electrical Code and local codes and
ordinances.
PREFERRED METHOD
: DO NOT USE AN EXTENSION CORD
on 230, 208, and 230/208 Volt units.
NOTICE
3-prong
grounding
3-prong
grounding
plug
type wall
receptacle
Ground
prong
Power
supply
cord
Ensure proper ground
exists before use
Fig. 24
DO NOT CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER PLUG.
FUSE – Use a time-delay fuse or circuit breaker. Refer
to serial plate for proper power supply
requirements.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Common
Issues
Common Problems and Solutions
Before calling for service, please review the following list of common problems and solutions.
The air conditioner is operating normally when:
• You hear a pinging noise. This is caused by water being picked up by the condenser on rainy days or in highly
humid conditions. This feature is designed to help remove moisture in the air and improve cooling efficiency.
• You hear the thermostat click. This is caused by the compressor cycle starting and stopping.
• You see water dripping from the rear of the unit. Water may be collected in the base pan in highly humid
conditions or on rainy days. This water overflows and drips from the rear of the unit.
• You hear the fan running while the compressor is silent. This is a normal operational feature.
The air conditioner may be operating abnormally when:
Problem
Possible Causes
What To Do
■ The air conditioner is unplugged or • Make sure the plug is completely plugged into
not plugged in completely the outlet
■ The fuse is blown/circuit breaker is • Check the fuse/circuit breaker box and replace
The air conditioner
does not operate
at all
triggered
the fuse or reset the breaker
■ Power failure.
• In the event of a power failure, set the power
control to OFF. When the power is restored,
wait 3 minutes to restart the air conditioner to
prevent the compressor from overloading
■ Air flow is restricted
• Make sure there are no curtains, blinds,
furniture or other obstacles in front of the air
conditioner
■ The THERMOSTAT may not be
set cool enough
• Turn the knob to a higher setting. The highest
setting provides maximum cooling
■ The air filter is dirty.
• Clean the filter at least every 2 weeks. Refer to
the “Care and Maintenance” section (p.11) of
the manual.
Air conditioner
does not cool
■ The air conditioner was just
turned on.
• After the air conditioner is turned on, you need
to give the air conditioner some time to cool the
room.
■ Cold air is escaping.
• Check for open furnace floor resisters and cold
air returns.
• CLOSE the air conditioner vent
■ Cooling coils are iced up
• See Ice appears on the air conditioner below
■ The cooling coils are iced over.
• Ice may block the air flow and obstruct the air
conditioner from properly cooling the room. Set
the fan at MED or HIGH while setting the
thermostat at 1 or 2 until the ice melts.
Ice appears on the
air conditioner.
■ You can refer to the Energy Star program in detail at "www.energystar.gov".
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LG ROOM AIR CONDITIONER LIMITED WARRANTY
-
USA
LG Ele c tro nic s Inc . will re p a ir o r a t its o p tio n re p la c e , witho ut c ha rg e , yo ur p ro d uc t if it p ro ve s to b e d e fe c tive in
m a te ria l o r wo rkm a nship und e r no rm a l use d uring the wa rra nty p e rio d se t fo rth b e lo w, e ffe c tive fro m the d a te o f
o rig ina l c o nsum e r p urc ha se o f the p ro d uc t. This lim ite d wa rra nty is g o o d o nly to the o rig ina l p urc ha se r o f the p ro d uc t
a nd e ffe c tive o nly whe n use d in the Unite d Sta te s inc lud ing Ala ska , Ha wa ii, a nd U.S. Te rrito rie s.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
C a ll 1-877-714-7486 a nd c ho o se the a p p ro p ria te p ro m p t. Ple a se
ha ve p ro d uc t typ e (Ro o m Air C o nd itio ne r), m o d e l num b e r, se ria l
num b e r, a nd ZIP/ p o sta l c o d e re a d y.
La b or: 2 Ye a rs fro m the Da te o f Purc ha se .
Pa rts: 2 Ye a rs fro m the Da te o f Purc ha se .
The wa rra nte d la b o r c o ve rs the c o st o f In-Ho m e Se rvic e o n a ll
p a rts inc lud ing the c o m p re sso r.
Com p re ssor: 5 Ye a rs fro m the Da te o f
Purc ha se .
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS
REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. LG WILL NOT BE LIABLE FOR
ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS, IN
CONNECTION WITH THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS
MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
1. Se rvic e trip s to yo ur ho m e to d e live r, p ic k up , a nd / o r insta ll the p ro d uc t, instruc t, o r re p la c e ho use fuse s o r
c o rre c t wiring , o r c o rre c tio n o f una utho rize d re p a irs; a nd
2. Da m a g e s o r o p e ra tin g p ro b le m s th a t re su lt fro m m isu se , a b u se , o p e ra tio n o u tsid e e n viro n m e n ta l
sp e c ific a tio ns o r c o ntra ry to the re q uire m e nts o r p re c a utio ns in the O p e ra ting G uid e , a c c id e nt, ve rm in,
fire , flo o d , im p ro p e r insta lla tio n, a c ts o f G o d , una utho rize d m o d ific a tio n o r a lte ra tio n, inc o rre c t e le c tric a l
c urre nt o r vo lta g e , o r c o m m e rc ia l use , o r use fo r o the r tha n inte nd e d p urp o se .
3. The re fore , the c ost of re p a ir or re p la c e m e nt of suc h a d e fe c tive p rod uc t sha ll b e b orne b y the c onsum e r.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
Re ta in your Sa le s Re c e ip t to p rove d a te of p urc ha se .
A c o p y o f yo u r Sa le s Re c e ip t m u st b e su b m itte d a t
the tim e wa rra nty se rvic e is p ro vid e d .
To Prove Wa rra nty Cove ra g e
Ca ll 1-877-714-7486, 24 hrs a d a y, 7 d a ys p e r we e k.
P re ss t h e a p p ro p ria t e o p t io n , a n d p le a se h a v e
yo u r p ro d u c t typ e (AIR C O NDITIO NER),a n d
ZIP/ p o sta l c o d e re a d y.
To Ob ta in Ne a re st Authorize d Se rvic e Ce nte r or Sa le s
De a le r, or to Ob ta in Prod uc t, Custom e r, or Se rvic e
Assista nc e
P/No.: 3828A20437A
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|