8” Bench Drill Press
Model: 30-100
Record the serial number and date of purchase
in your manual for future reference.
Serial number:
Date of purchase:
For more information:
For Parts or Questions:
Part # 30-100M2
Download from Www.Somanuals.com. All Manuals Search And Download.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.
ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.
NEVER LEAVE TOOLS RUNNING UNATTENDED.
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that is damaged should be checked to
assure that it will operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its
operation. A guard or other damaged parts should immediately be properly repaired or replaced.
Special Safety Rules For Drill Presses
1. Do Not operate the Drill Press until it is assembled
14. Never operate the Drill Press with a damaged drill
bit, cutting tool or accessory.
15. Always check the drill bit, cutting tool or accessory
in tight in the chuck.
16. Never operate the Drill Press with the chuck key
in the chuck.
17. Always adjust the depth stop to avoid drilling into
the table surface.
18. Never drill material unless it is properly supported.
Non flat work-pieces require additional support.
19. Always clamp the work piece to the table.
20. Always support large work-pieces at the same
height as the table.
21. Never remove the work-piece or clear the table
until the Drill Press comes to a complete stop.
22. Always wear a face shield and safety glasses while
operating the Drill Press.
23. Never operate the Drill Press with missing,
damaged, worn, loose or defective parts.
24. Never adjust, change speeds or perform
maintenance on the Drill Press while it is operating.
25.Always clean the work surface and work area when
finished operating the Drill Press.
26. Always disconnect the power when adjusting or
performing maintenance on the Drill Press.
27. Always disconnect the power when finished using
the Drill Press to prevent accidental operation.
and you have read the instructions.
2. Do not operate the Drill Press unless you are familiar
with its safe operation. If you are not familiar with
the operation of a Drill Press seek advice from your
supervisor, instructor or other qualified individual.
3. If you are using a bench top Drill Press, it must be
securely fastened to a stand or bench.
4. If you are operating a floor Drill Press it must be
securely fastened to the floor.
5. Always clear the table and work area before turning
on the Drill Press.
6. Always use drill bits, cutting tools and accessories
with a ½” shank or less.
7. Never place hands near the drill bit, cutting tool or
accessory.
8. Never wear loose clothing, gloves or ties while
operating the Drill Press.
9. Always have a firm footing while operating the Drill
Press.
10. Always keep work surface and work areas clear of
debris.
11. Never attempt to do set-up work, assembly or layout
work on the Drill Press while it is in operation.
12. Never start the Drill Press with the drill bit, cutting
tool or accessory in contact with the work-piece.
13. Always lock all table, column and head locks before
turning on the Drill Press.
California Proposition 65 Warning
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Your risk from
exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in
a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out
microscopic particles.
For more detailed information about California Propostion 65 log onto rikontools.com.
SAVE THESE INSTRUCTIONS.
Refer to them often.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Warnings......................................................................................................................................2-3
Special Safety Rules For Drill Presses............................................................................................. 3
Specifications.........................................................................................................................................................4
UnpackingandContents......................................................................................................................................5
Getting to Know Your Drill Press..............................................................................................................6
Assembly................................................................................................................................................................7-9
Adjustments.......................................................................................................................................9-10
Troubleshooting.........................................................................................................................................................11
Notes......................................................................................................................................................................12
Wiring Diagram......................................................................................................................................12
ElectricalRequirements...................................................................................................................................13
Explosion Diagrams/Parts Lists...........................................................................................................14-21
Warranty.................................................................................................................................................................22
Notes......................................................................................................................................................................23
Specifications
Model Number
Swing
30-100
8”
Motor
1/3 HP, 120V, 3.6A, 60Hz
Motor Speed
Spindle Speeds
Chuck Type
Chuck Capacity
Spindle Taper
Spindle Travel
Drilling Capacity
Quill Diameter
Table Size
1750 RPM
620, 1100, 1720, 2340, 3100 RPM
Keyed
1/2”
JT33
2”
1/2”
1-1/2”
6-5/8”L x 6-3/8”W
2”
Column Diameter
Net Weight
42LBS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of Package
Unpacking and Checking Contents
Unpack your drill press from its carton and check to see that you have all of the following items. Set
packing material and shipping carton to the side. Do not discard until machine has been set up and
is running properly.
Do not turn your machine ON if any of these items are missing. You may cause injury to yourself or
damage to your machine. If parts are missing contact RIKON customer service at 877-884-5167 or
8
7
1
2
3
4
5
6
Item Description
Item Description
1
2
3
4
5
6
7
8
Drill Press Head
Base
Table
1/2” Chuck
Chuck Key
Hardware Bag (See Contents Below) 14
Feed Handle
Column
9
Table Lock Handle
10
11
12
13
Column Mounting Bolts
3mm Hex Wrench
4mm Hex Wrench
6mm Hex Wrench
Feed Handle Bolt
Owner’s Manual
15
15
8” Bench Drill Press
Model: 30-100
13
12
11
14
9
Record the serial number and date of purchase
in your manual for future reference.
Serial number:
10
Date of purchase:
For more information:
For Parts or Questions:
Part
#
30-100M2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know Your Drill Press
7
12
6
5
11
8
9
10
4
3
2
1
Item Description
Item Description
1
2
3
4
5
6
Base
Table Lock Handle
Table
Column Support Tube
Handle Return Spring
Depth Stop
7
8
9
10
11
12
Belt Cover
Motor
Feed Handle
Chuck
Chuck Key Holder
Switch
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
The machine must not be plugged in and the power switch must be in the OFF position
until assembly is complete.
Tools Required for Assembly
Item
Description
Phillips Screwdriver
Adjustable or 13mm Wrench
Unpacking and Clean-up
1. Carefully finish removing all contents from shipping carton. Compare contents of the
shipping carton with the list shown on page 5. Place parts on a protected surface.
2. Report any shipping damage to your local distributor. If parts are missing contact
RIKON customer service at 877-884-5167 or techsupport@rikontools.com.
3. Clean all rust protected surfaces. Do not use; gasoline, paint thinner, mineral spirits,
etc. These may damage painted surfaces.
4. Set packing material and shipping carton to the side. Do not discard until machine
has been set up and is running properly.
1. Install the column to the base using the three
column mounting bolts. (Fig.01)
Fig.01
2. Next install the table lock handle through the
unthreaded hole on the left of the table
support casting. The handle should engage
the thread on the right side of the table
support casting. (Fig.02)
Fig.02
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
3. Slide the drill press head over the column.
(Fig.03)
Fig.03
4. Center the drill press head over the table and
base. Tighten the drill press head into position
by locking the two hex screws on the side of
the casting. (A-Fig.04)
A
Fig.04
5. Next, slide the 1/2” chuck (A-Fig.05) over the
pre-installed spindle (B-Fig.05). Open the
chuck jaws fully and tap into place using a
rubber mallet or a hammer and block of wood.
B
A
Fig.05
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
6. The feed handle (A-Fig.06) is secured to the
feed shaft with the supplied Allen bolt
(B-Fig.06).
B
A
Fig.06
Adjustments
7. Depth Stop: The depth stop and scale are
found on the left side of the switch box. To
adjust, lower the drill chuck until pointer shows
desired depth on the scale. Loosen the
lower nut on the threaded shaft (A-Fig.07) until
it bottoms out on the head casting (B-Fig.07).
Tighten upper nut against the lower nut to
retain the adjustment.
A
B
Fig.07
8. Table Tilt: The drill press table will tilt 0-45
degrees left and right. To tilt, loosen the nut
located under the table (A-Fig.08). Align the
“zero” mark on the table (B-Fig.08) to the
desired degree marking on the scale. Tighten
the nut under the table to retain the
adjustment.
A
B
Fig.08
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
9. Changing Spindle Speed: The 30-100 Bench
A
Drill Press has five spindle speeds. To change,
lift the cover with the handle (A-Fig.09).
Fig.09
Fig.10
Fig.11
10. Loosen the motor lock knob (A-Fig.10). Move
the motor (B-Fig.10) manually toward the
feed handle to take tension off of the belt.
A
B
11.Move the drive belt to the desired speed
position, refer to speed chart inside belt cover.
Manually move the motor away from the feed
handle until the belt is tensioned, tighten
motor lock knob. The belt is properly
tensioned when the deflection distance is 1/2”
when pushed by hand (Fig.11).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Use this section to record maintenance, service and any calls to Technical Support:
Wiring Diagram
WARNING:This machine must be grounded.
Replacement of the power supply cable should only be done by a qualified electrician.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Requirements
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do
not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded.
Use only three wire extension cords that have three-prong grounding plugs and three-pole
receptacles that accept the tool’s plug.*
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet that looks the one illustrated in Figure
A below. The tool has a grounding plug that looks like the grounding plug as illustrated in Figure A
below. A temporary adapter, which locks like the adapter as illustrated in Figure B below, may be
used to connect this plug to a two-pole receptacle, as shown in Figure B if a properly grounded outlet
is not available.** The temporary adapter should only be used until a properly grounded outlet can
be installed by a qualified electrician. The green colored rigid ear or tab, extending from the adapter,
must be connected to a permanent ground such as a properly grounded outlet box.
* Canadian electrical codes require extension cords to be certified SJT type or better.
** Use of an adapter in Canada is not acceptable.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Explosion Diagram
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
KEY No.
Description
30-100-1A
30-100-2A
30-100-3A
30-100-4A
30-100-5A
30-100-6A
30-100-7A
30-100-8A
30-100-9A
30-100-10A
30-100-11A
30-100-12A
30-100-13A
30-100-14A
30-100-15A
Bushing-Rubber
Knob
Screw-Pan Hd.M5x0.8-1.2
Belt-”V” 5/16x26
Guard w/Labels
Screw-Washer Hd.
Ring Retaining
Bearing-Ball 17mm
Spacer
Insert-Pulley
Pulley-Spindle
Nut-Pulley
Clamp Cord
Screw-Pan Hd.M5x.08-16
Washer,Foam
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Explosion Diagram
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
KEY No.
Description
30-100-1C
30-100-2C
30-100-3C
30-100-4C
30-100-5C
30-100-6C
30-100-7C
30-100-8C
30-100-9C
30-100-10C
30-100-11C
30-100-12C
Gasket-Quill
Bearing-Ball 12mm
Tube-Quill
Screw-Pan M5x0.8-20
Collar-Stop
Ring Retaining
Shaft-Spindle
Chuck
Key-Chuck
Nut-Hex M6x1.0
Nut-Hex M5x.08
Rod-Stop
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Explosion Diagram
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
KEY No.
30-100-1D
30-100-2D
30-100-3D
30-100-4D
30-100-5D
30-100-6D
30-100-7D
Description
Support-Table w/Scale
Support-Lock Handle
Tube/Support
Base
Screw-Hex Hd. M8x1.25-20
Screw-Hex Hd. 1/2-12x7/8
Table
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
5-Year Limited Warranty
RIKON Power Tools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our
products that each product be free from defects in materials and workmanship for a period of five
(5) years from the date the product was purchased at retail. This warranty may not be transferred.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence,
accidents, repairs, alterations, lack of maintenance or normal wear and tear. Under no
circumstances will Seller be liable for incidental or consequential damages resulting from
defective products. All other warranties, expressed or implied, whether of merchantability,
fitness for purpose, or otherwise are expressly disclaimed by Seller. This warranty does not cover
products used for commercial, industrial or educational purposes.
This limited warranty does not apply to accessory items such as blades, drill bits, sanding discs or
belts and other related items.
Seller shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty proof of purchase documentation, which includes date of
purchase and an explanation of the complaint, must be provided.
The Seller reserves the right to effect at any time, without prior notice, those alterations to parts,
fittings, and accessory equipment which they may deem necessary for any reason whatsoever.
To take advantage of this warranty, please fill out the enclosed warranty card and send it to:
RIKON Warranty
16 Progress Rd.
Billerica, MA 01821
The card must be entirely completed in order for it to be valid. If you have any questions
please contact us at 877-884-5167 or warranty@rikontools.com.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
For more information:
16 Progress Rd
Billerica, MA 01821
877-884-5167 / 978-528-5380
Copyright RIKON Power Tools, Inc. 2011
Printed in China 7/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Kyocera Network Router KR1 User Manual
La Crosse Technology Watch XG 20 User Manual
Land Pride Brush Cutter rcf3696 User Manual
LG Electronics Cell Phone Vortex User Manual
Lincoln Electric Welding System IM520 B User Manual
Lochinvar Water Pump BLT2026 User Manual
Lux Products Thermostat PSP711TS User Manual
Maverick Ventures Thermometer ET 8 User Manual
Melissa Scale 231 004 User Manual
Memorex Portable Speaker Mi3001 User Manual