KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
VS-66HN
6x6 HDMI Matrix Switcher
P/N: 2900-300154 Rev 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
VS-66HN - Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Video Products.
Congratulations on purchasing your Kramer VS-66HN 6x6 HDMI Matrix Switcher,
which is ideal for the following typical applications:
Conference room presentations
Advertising applications
Rental and staging
VS-66HN - Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
to check for up-to-date user manuals, application programs, and to check
if firmware upgrades are available (where appropriate).
i
2.1
Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer High-
performance high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
Position your Kramer product away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
!
2
VS-66HN - Getting Started
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
!
Warning: Use only the power cord that is supplied with the unit
Warning: Do not open the unit. High voltages can cause
electrical shock! Servicing by qualified personnel only
Warning: Disconnect the power and unplug the unit from the wall
before installing
2.3
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
VS-66HN - Getting Started
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Overview
The VS-66HN is a high quality 6x6 matrix switcher for HDMI signals. It reclocks
and equalizes the signal and can route any input to any or all outputs
simultaneously.
In particular, the VS-66HN features:
Up to 6.75Gbps data rate (2.25Gbps per graphics channel)
Suitable for resolutions up to UXGA at 60Hz and for all HD resolutions.
Support for HDCP (High Definition Digital Content Protection)
HDMI support for 3D, Deep Color, x.v.Color™, Lip Sync
3D pass-through
Support for up to 7.1 multichannel audio
I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID
handling and processing algorithm ensures Plug and Play operation for
HDMI systems
Kramer reKlocking™ and Equalization Technology that rebuilds the digital
signal to travel longer distances
A lock button to prevent unwanted tampering with the buttons on the front
panel
12 Preset memory locations for quick access to common configurations
You can control the VS-66HN using the front panel buttons, or remotely via:
RS-232 serial commands transmitted by a PC, touch screen system or other
serial controller
The Kramer infrared remote control transmitter
A PC connected to the Ethernet port on the device via a LAN
3.1
Defining the VS-66HN 6x6 HDMI Matrix Switcher
This section defines the VS-66HN.
4
VS-66HN - Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1: VS-66HN 6x6 HDMI Matrix Switcher Front Panel
#
Feature
Function
1
IR Indication LED
IR Receiver
POWER LED
ALL Button
Lights yellow when receiving signals from the infrared remote control transmitter
Signal receiver for the infrared remote control transmitter
Lights when the device is turned on
2
3
4
Press followed by an input button to connect the selected input to all outputs
For example, press ALL and then Input button # 2 to connect input # 2 to all the outputs
5
6
7
OFF Button
Press after pressing an output button to disconnect the selected output from the inputs. To
disconnect all the outputs, press ALL followed by OFF
IN (1 to 6)
Press to select the input to switch after selecting an output (also used for storing machine
SELECT Buttons
OUT (1 to 6)
Press to select an output to switch followed by an input (also used for storing machine
8
STO Button
RCL Button
LOCK Button
9
10
Press and hold to toggle the locking/release of the front panel buttons.
11
12
EDID Button
INPUT 7-segment LED Display
Displays the input currently switched to the output which is marked above each input
VS-66HN - Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2: VS-66HN 6x6 HDMI Matrix Switcher Rear Panel
#
Feature
Function
13
14
15
16
17
OUTPUT HDMI Connectors (1 to 6)
INPUT HDMI Connectors (1 to 6)
RS-232 9-pin D-sub Connector
ETHERNET RJ-45 Connector
RESET Button
Connect to up to 6 HDMI acceptors
Connect to up to 6 HDMI sources
Connect to a PC/serial controller
Connect to a PC via a LAN
Press to reset to the factory default IP parameters:
IP number 192.168.1.39
Mask – 255.255.255.0
Gateway – 192.168.1.1
Depress the button while powering on the device. The device powers up with the factory
default IP parameters
18
REMOTE IR Opening
Connect to an external IR receiver for controlling the device via and IR remote controller
Covered by a cap. The 3.5mm jack at the end of the internal IR connection cable fits into this
opening
19
20
21
Mains Power Connector
Mains Power Fuse
Connect to the mains power
Fuse for protecting the device
Switch for turning the device on or off
Mains Power Switch
VS-66HN - Overview
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2
Using the IR Transmitter
You can use the RC-IR3 IR transmitter to control the machine via the built-in IR
receiver on the front panel or, instead, via an optional external IR receiver (Model:
C-A35M/IRR-50). The external IR receiver can be located up to 15 meters away
from the machine. This distance can be extended to up to 60 meters when used
with three extension cables (Model: C-A35M/A35F-50).
Before using the external IR receiver, be sure to arrange for your Kramer dealer to
insert the internal IR connection cable (P/N: 505-70434010-S) with the 3.5mm
connector that fits into the REMOTE IR opening on the rear panel. Connect the
external IR receiver to the REMOTE IR 3.5mm connector.
VS-66HN - Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Connecting the VS-66HN 6x6 HDMI Matrix
Switcher
Always switch off the power to each device before connecting it to your
VS-66HN. After connecting your VS-66HN, connect its power and then
i
switch on the power to each device.
To connect the VS-66HN 6x6 HDMI Matrix Switcher as illustrated in the
1. Connect up to six HDMI sources (for example, DVD players) to the IN HDMI
connectors.
You do not have to connect all the sources.
2. Connect the six OUT HDMI connectors to up to six HDMI acceptors (for
example, LCD displays with built-in speakers).
You do not have to connect all the outputs.
3. If required, connect a PC/controller to the RS-232 port (see Section 6.6)
4. Connect the device to the mains electricity (not shown in Figure 3).
5. If necessary, acquire the EDID (see Section 6.2)
VS-66HN - Connecting the VS-66HN 6x6 HDMI Matrix Switcher
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Operating the VS-66HN 6x6 HDMI Matrix
Switcher
This section describes:
6.1
6.2
Switching an Input to an Output
To switch an input to an output:
Press an output button followed by an input button to switch the selected
input to the selected output
Acquiring the EDID
You can acquire the EDID from any of the following:
Note: Attempting to acquire the EDID from an output that does not have a display
device connected to it results in the default EDID being acquired.
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2.1
Acquiring the EDID from One Output
Note: You can assign the EDID from one output to any or all of the six inputs.
To acquire the EDID from a display device connected to one of the outputs:
1. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
2. Press the input button to which the EDID is copied.
The selected input number flashes on the display.
3. Select the output from which the EDID is to be acquired.
4. Press the EDID button.
The EDID is stored when the display returns to normal and the EDID and
STO buttons stop flashing.
6.2.2
Acquiring the EDID from Different Outputs to Different Inputs
To acquire the EDID from several outputs (for example, OUT 1 to IN 1 and
OUT 6 to IN 3):
1. Connect the display devices to the outputs from which you want to acquire
the EDIDs.
2. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
3. Press the input button to which the EDID is copied (for example, IN 1).
The selected input number flashes on the display.
4. Select the output from which the EDID is acquired (for example, OUT 1).
5. Press the IN 1 button.
The IN 1 button stops flashing.
6. Press the next input button to which the EDID is copied (for example, IN 3).
The selected input number flashes on the display.
12
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Select the output from which the EDID is acquired (for example,
OUT 6).
8. Press the IN 3 button.
The IN 3 button stops flashing.
9. Press the input buttons to which you want to copy the EDID (for example, IN
1 and IN 3).
10. Make sure that the relevant input numbers flash on the display.
11. Press the EDID button.
The process is complete when the display returns to normal.
6.2.3
Acquiring the Default EDID
To store the default EDID on a selected input (for example, Input 2):
1. Press the EDID and STO buttons simultaneously and hold them for 3
seconds.
Both buttons flash.
2. Press the input (for example, Input 2) to which the EDID is to be copied.
The selected input number flashes on the display.
3. Press the OFF button until "0" (zero) appears on the display.
4. Press the EDID button.
The default EDID is stored on the selected input when the display returns to
normal.
6.3
Storing and Recalling a Preset
You can use the STO and RCL buttons to store up to 12 setups and then recall
Figure 4: Store-Recall Button Configuration
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To store a preset (for example, to preset 10):
1. Configure the switching as required for the preset.
2. Press the STO button.
The STO button flashes.
3. Select an OUT or IN SELECT button to store the device setting (for example,
IN 4 for preset 10).
4. Press the STO button to store the current setup.
You have to press the STO button within 10 seconds or the procedure automatically
times out.
To recall a preset (for example, preset 10):
1. Press the RCL button.
The RCL button flashes.
2. Press the relevant OUT or IN button that stored the preset (for example, IN
4/preset 10).
3. Press the RCL button to recall the stored preset.
The RCL button stops flashing.
6.4
Resetting the IP Parameters
This procedure resets only the IP related parameters. All switching and
preset values remain unchanged.
i
To reset the IP parameters to their default values (see Section 8):
Press and hold the ETH Reset button on the rear panel while powering up
the device
14
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
Download from Www.Somanuals.com. All Manuals Search And Download.
6.5
Switching Between Protocol 2000 and Protocol 3000
To switch from Protocol 2000 to Protocol 3000 and vice-versa using the front
panel buttons:
1. Press Output buttons 1 and 3 at the same time.
Protocol 3000 is active.
2. Press Output buttons 1 and 2 at the same time.
Protocol 2000 is active.
Note that when sending consecutive protocol commands make sure to
maintain at least a 200ms delay between commands.
i
After performing EDID get/store commands, a 1 sec delay is required
before sending another protocol command.
6.6
Connecting via RS-232
You can connect to the VS-66HN via an RS-232 connection using, for example, a
PC. Note that a null-modem adapter/connection is not required.
To connect to the product via RS-232:
Connect the RS-232 9-pin D-sub on the rear panel of the VS-66HN via a
9-wire straight cable (only pin 2 to pin 2, pin 3 to pin 3, and pin 5 to pin 5 need to
be connected) to the RS-232 9-pin D-sub port on your PC
6.7
Connecting via the Ethernet
You can connect to the VS-66HN via Ethernet using either of the following
methods:
Via a network hub, switch, or router, using a straight-through cable (see
Note: If you want to connect via a router and your IT system is based on IPv6,
speak to your IT department for specific installation instructions.
After connecting the Ethernet port, you have to install and configure your Ethernet Port. For
detailed instructions, see the “Ethernet Configuration (FC-11) guide.pdf” file in the technical
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.7.1
Connecting the Ethernet Port directly to a PC
You can connect the Ethernet port of the VS-66HN directly to the Ethernet port on
your PC using a crossover cable with RJ-45 connectors.
This type of connection is recommended for identifying the VS-66HN
with the factory configured default IP address.
i
After connecting the VS-66HN to the Ethernet port, configure your PC as follows:
1. Click Start > Control Panel > Network and Sharing Center.
2. Click Change Adapter Settings.
3. Highlight the network adapter you want to use to connect to the device and
click Change settings of this connection.
The Local Area Connection Properties window for the selected network
Figure 5: Local Area Connection Properties Window
16
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Highlight either Internet Protocol Version 6 (TCP/IPv6) or Internet
Protocol Version 4 (TCP/IPv4) depending on the requirements of your IT
system.
5. Click Properties.
The Internet Protocol Properties window relevant to your IT system appears
Figure 6: Internet Protocol Version 4 Properties Window
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7: Internet Protocol Version 6 Properties Window
6. Select Use the following IP Address for static IP addressing and fill in the
For TCP/IPv4 you can use any IP address in the range 192.168.1.1 to
192.168.1.255 (excluding 192.168.1.39) that is provided by your IT
department.
18
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8: Internet Protocol Properties Window
7. Click OK.
8. Click Close.
6.7.2
6.7.3
Connecting the Ethernet Port via a Network Hub or Switch
You can connect the Ethernet port of the VS-66HN to the Ethernet port on a
network hub or using a straight-through cable with RJ-45 connectors.
Control Configuration via the Ethernet Port
To control several units via Ethernet, connect the Master unit (Device 1) via the
Ethernet port to the Ethernet port of your PC. Use your PC provide initial
6.8
Upgrading the Firmware
For instructions on upgrading the firmware see “Upgrading the VS-66HN Firmware
Using the STC Software”.
VS-66HN - Operating the VS-66HN 6x6 HDMI Matrix Switcher
19
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Technical Specifications
INPUTS:
6 HDMI connectors
6 HDMI connectors
OUTPUTS:
BANDWIDTH:
Up to 6.75Gbps data rate (2.25Gbps per graphics
channel)
COMPLIANCE WITH HDMI
STANDARD:
HDMI and HDCP
RESOLUTION:
Up to UXGA; 1080p
POWER CONSUMPTION:
CONTROLS:
100240V AC, 50/60Hz, 40VA
Front panel buttons, infrared remote control
transmitter, RS-232, Ethernet
OPERATING TEMPERATURE:
STORAGE TEMPERATURE:
HUMIDITY:
0° to +40°C (32° to 104°F)
-40° to +70°C (-40° to 158°F)
10% to 90%, RHL non-condensing
19” x 7” x 1U (W, D, H)
DIMENSIONS:
WEIGHT:
2.5kg (5.5lbs) approx.
ACCESSORIES:
OPTIONS:
Power cord, IR transmitter, rack ”ears”
External remote IR receiver cable
20
VS-66HN - Technical Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Default Communication Parameters
RS-232
Protocol 2000 (Default)
Protocol 3000
Baud Rate
Data Bits
Baud Rate
Data Bits
9600
9600
8
8
Stop Bits
1
Stop Bits
1
Parity
None
Parity
None
Command Format
HEX
Command Format
ASCII
Example (Output
1 to Input 1)
0x01, 0x81, 0x81, 0x81
Example (Output 1 to
Input 1)
#VID1>1<CR>
Switching Protocol
P2000 –> P3000
P3000 –> P2000
Command
0x38, 0x80, 0x83, 0x81
Command
#P2000<CR>
Front Panel
Press and hold Output 1 and Front Panel
Output 3 simultaneously
Press and hold Output 1
and Output 2 simultaneously
Ethernet
IP Address
Subnet Mask
192.168.1.39
255.255.255.0
TCP Port
UDP Port
5000 or 10001 or 50000
50000
VS-66HN - Default Communication Parameters
21
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Default EDID
Monitor
Model name............... VS-66HN
Manufacturer............. KMR
Plug and Play ID......... KRM0200
Serial number............ 1
Manufacture date......... 2010, ISO week 24
-------------------------
EDID revision............ 1.3
Input signal type........ Digital (DVI)
Color bit depth.......... Undefined
Display type............. RGB color
Screen size.............. 700 x 390 mm (31.5 in)
Power management......... Not supported
Extension blocs.......... 1 (CEA-EXT)
-------------------------
DDC/CI................... Not supported
Color characteristics
Default color space...... Non-sRGB
Display gamma............ 2.20
Red chromaticity......... Rx 0.640 - Ry 0.341
Green chromaticity....... Gx 0.286 - Gy 0.610
Blue chromaticity........ Bx 0.146 - By 0.069
White point (default).... Wx 0.284 - Wy 0.293
Additional descriptors... None
Timing characteristics
Horizontal scan range.... 31-94kHz
Vertical scan range...... 50-85Hz
Video bandwidth.......... 170MHz
CVT standard............. Not supported
GTF standard............. Not supported
Additional descriptors... None
Preferred timing......... Yes
Native/preferred timing.. 1280x720p at 60Hz
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 746 +hsync -vsync
Detailed timing #1....... 1920x1080p at 60Hz (16:9)
Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
22
VS-66HN - Default EDID
Download from Www.Somanuals.com. All Manuals Search And Download.
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 720p at 60Hz - VESA STD
1280 x 800p at 60Hz - VESA STD
1440 x 900p at 60Hz - VESA STD
1280 x 960p at 60Hz - VESA STD
1280 x 1024p at 60Hz - VESA STD
1400 x 1050p at 60Hz - VESA STD
1680 x 1050p at 60Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
EIA/CEA-861 Information
Revision number.......... 3
IT underscan............. Not supported
Basic audio.............. Supported
YCbCr 4:4:4.............. Not supported
YCbCr 4:2:2.............. Not supported
Native formats........... 1
Detailed timing #1....... 720x480p at 60Hz (4:3)
Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync
Detailed timing #2....... 1920x1080i at 60Hz (16:9)
Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync
+vsync
Detailed timing #3....... 1920x1080i at 50Hz (16:9)
Modeline............... "1920x1080" 74.250 1920 2448 2492 2640 1080 1084 1094 1124 interlace +hsync
+vsync
Detailed timing #4....... 1280x720p at 60Hz (16:9)
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
Detailed timing #5....... 1280x720p at 50Hz (16:9)
Modeline............... "1280x720" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
CE video identifiers (VICs) - timing/formats supported
720 x 576p at 50Hz - EDTV (4:3, 16:15)
1280 x 720p at 50Hz - HDTV (16:9, 1:1)
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1920 x 1080i at 50Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1) [Native]
1920 x 1080p at 60Hz - HDTV (16:9, 1:1)
1920 x 1080p at 50Hz - HDTV (16:9, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001
CE audio data (formats supported)
LPCM 3-channel, 24-bits
at 44/48 kHz
CE speaker allocation data
Channel configuration.... 7.1
Front left/right......... Yes
Front LFE................ No
Front center............. Yes
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
VS-66HN - Default EDID
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear LFE................. No
CE vendor specific data (VSDB)
IEEE registration number. 0x000C03
CEC physical address..... 1.0.0.0
Maximum TMDS clock....... 165MHz
Report information
Date generated........... 08/03/2011
Software revision........ 2.52.0.857
Data source.............. Real-time 0x0031
Operating system......... 5.1.2600.2.Service Pack 3
24
VS-66HN - Default EDID
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Kramer Protocol 2000
The Kramer Protocol 2000 RS-232/RS-485 communication uses four bytes of
information as defined below. All the values in the table are decimal, unless
otherwise stated.
MSB
LSB
1st Byte
DESTINATION
INSTRUCTION
0
7
D
6
N5
5
N4
4
N3
3
N2
2
N1
1
N0
0
2nd Byte
INPUT
1
7
I6
6
I5
5
I4
4
I3
3
I2
2
I1
1
I0
0
3rd Byte
OUTPUT
1
7
O6
6
O5
5
O4
4
O3
3
O2
2
O1
1
O0
0
4th Byte
MACHINE NUMBER
1
7
OVR
6
X
5
M4
4
M3
3
M2
2
M1
1
M0
0
1st Byte:
Bit 7 – Defined as 0
D – DESTINATION:
0 – Sends information to the switchers (from the PC)
1 – Sends information to the PC (from the switcher)
N5…N0 – INSTRUCTION
The 6-bit INSTRUCTION defines the function performed by the switcher(s). If a function is performed using the
machine’s keyboard, these bits are set with the INSTRUCTION NO. performed. The instruction codes are defined
according to the table below (INSTRUCTION NO. is the value set in N5…N0).
2nd Byte:
Bit 7 – Defined as 1
I6…I0 – INPUT
When switching (i.e. instruction codes 1 and 2), the 7-bit INPUT is set as the input number to be switched. If switching is
done using the machine’s front panel, these bits are set with the INPUT NUMBER switched. For other operations, these
bits are defined according to the table.
3rd Byte:
Bit 7 – Defined as 1
O6…O0 – OUTPUT
When switching (i.e. instruction codes 1 and 2), the 7-bit OUTPUT is set as the output number to be switched. If
switching is done using the machine’s front panel, these bits are set with the OUTPUT NUMBER switched. For other
operations, these bits are defined according to the table.
4th Byte:
Bit 7 – Defined as 1
Bit 5 – Don’t care
OVR – Machine number override
M4…M0 – MACHINE NUMBER
This byte is used to address machines in a system by their machine numbers. When several machines are controlled
from a single serial port, they are usually configured together and each machine has an individual machine number. If
the OVR bit is set, then all machine numbers accept (implement) the command and the addressed machine replies.
When a single machine is controlled over the serial port, always set M4…M0 to 1, and make sure that the machine itself
is configured as MACHINE NUMBER = 1.
VS-66HN - Kramer Protocol 2000
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Instruction Codes for Protocol 2000
Instruction Definition for Specific Instruction
Description Input Output
Notes
#
0
1
RESET VIDEO
SWITCH VIDEO
0
0
1
Set equal to video input which is Set equal to video output which is
2, 15
to be switched
(0 = disconnect)
Set as SETUP #
to be switched
(0 = to all the outputs)
0 - to store
1 - to delete
0
3
4
5
STORE VIDEO
STATUS
RECALL VIDEO
STATUS
REQUEST STATUS
OF A VIDEO OUTPUT
2, 3, 15
2, 3, 15
4, 3
Set as SETUP #
Set as SETUP #
Equal to output number whose
status is reqd
15 REQUEST WHETHER SETUP #
0 - for checking if setup is defined
1 - for checking if input is valid
8
SETUP IS DEFINED /
VALID INPUT IS
or
Input #
DETECTED
30 LOCK FRONT PANEL
0 - Panel unlocked
1 - Panel locked
0
2
31 REQUEST WHETHER
PANEL IS LOCKED
0
0
16
56 CHANGE TO ASCII
0
Kramer protocol 3000
19
13
61
1 - video machine name
2 - audio machine name
3 - video software version
4 - audio software version
5 - RS422 controller name
6 - RS422 controller version
7 - remote control name
8 - remote software version
9 - Protocol 2000 revision
0 - Request first 4 digits
1 - Request first suffix
2 - Request second suffix
3 - Request third suffix
10 - Request first prefix
11 - Request second prefix
12 - Request third prefix
IDENTIFY
MACHINE
62 DEFINE MACHINE
1 - number of inputs
2 - number of outputs
3 - number of setups
1 - for video
2 - for audio
3 - for SDI
14
4 - for remote panel
5 - for RS-422 controller
NOTES on the above table:
NOTE 1 - When the master switcher is reset, (e.g. when it is turned on), the reset code is sent to the PC. If this code is
sent to the switchers, it resets according to the present power-down settings.
NOTE 2 - These are bi-directional definitions. That is, if the switcher receives the code, it performs the instruction; and if
the instruction is performed (due to a keystroke operation on the front panel), then these codes are sent. For example, if
the HEX code
01
85
88
83
was sent from the PC, then the switcher (machine 3) switches input 5 to output 8. If the user switched input 1 to output 7
via the front panel keypad, then the switcher sends HEX codes:
41
81
87
83
to the PC.
When the PC sends one of the commands in this group to the switcher, then, if the instruction is valid, the switcher
replies by sending to the PC the same four bytes that it was sent (except for the first byte, where the DESTINATION bit
is set high).
NOTE 3 - SETUP # 0 is the present setting. SETUP # 1 and higher are the settings saved in the switcher's memory, (i.e.
those used for Store and Recall).
NOTE 4 - The reply to a "REQUEST" instruction is as follows: the same instruction and INPUT codes as were sent are
returned, and the OUTPUT is assigned the value of the requested parameter. The replies to instructions 10 and 11 are
as per the definitions in instructions 7 and 8 respectively. For example, if the present status of machine number 5 is
breakaway setting, then the reply to the HEX code
0B
would be HEX codes
4B 80
80
80
81
85
85
NOTE 8 - The reply is as in TYPE 3 above, except that here the OUTPUT is assigned with the value 0 if the setup is not
defined / no valid input is detected; or 1 if it is defined / valid input is detected.
NOTE 13 - This is a request to identify the switcher/s in the system. If the OUTPUT is set as 0, and the INPUT is set as
1, 2, 5 or 7, the machine sends its name. The reply is the decimal value of the INPUT and OUTPUT. For example, for a
2216, the reply to the request to send the audio machine name would be (HEX codes):
7D
96
90
81 (i.e. 128dec+ 22dec for 2nd byte, and 128dec+ 16dec for 3rd byte).
26
VS-66HN - Kramer Protocol 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
If the request for identification is sent with the INPUT set as 3 or 4, the appropriate machine sends its software version
number. Again, the reply would be the decimal value of the INPUT and OUTPUT - the INPUT representing the number
in front of the decimal point, and the OUTPUT representing the number after it. For example, for version 3.5, the reply to
the request to send the version number would be (HEX codes):
7D
83
85
81 (i.e. 128dec+ 3dec for 2nd byte, 128dec+ 5dec for 3rd byte).
If the OUTPUT is set as 1, then the ASCII coding of the lettering following the machine’s name is sent. For example, for
the VS-7588YC, the reply to the request to send the first suffix would be (HEX codes):
7D
D9
C3
81 (i.e. 128dec+ ASCII for “Y”; 128dec+ ASCII for “C”).
NOTE 14 - The number of inputs and outputs refers to the specific machine which is being addressed, not to the system.
For example, if six 16X16 matrices are configured to make a 48X32 system (48 inputs, 32 outputs), the reply to the HEX
code
3E
82
81
82 (ie. request the number of outputs)
would be HEX codes
7E
82
90
82
ie. 16 outputs
NOTE 15 – When the OVR bit (4th byte) is set, then the “video” commands have universal meaning. For example,
instruction 1 (SWITCH VIDEO) causes all units (including audio, data, etc.) to switch. Similarly, if a machine is in
“FOLLOW” mode, it performs any “video” instruction.
NOTE 16 - The reply to the “REQUEST WHETHER PANEL IS LOCKED” is as in NOTE 4 above, except that here the
OUTPUT is assigned with the value 0 if the panel is unlocked, or 1 if it is locked.
NOTE 19 - After this instruction is sent, the unit will respond to the ASCII command set defined by the OUTPUT byte.
The ASCII command to operate with the HEX command set must be sent in order to return to working with HEX codes.
VS-66HN - Kramer Protocol 2000
27
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Protocol 3000
compatible with Kramer’s protocol 3000.
Note that the VS-66HN needs to be set to protocol 2000 in order to
use the IR remote control.
i
The VS-66HN can be operated using serial commands from a PC, remote
controller or touch screen using the Kramer Protocol 3000.
This section describes:
11.1 Kramer Protocol 3000 Syntax
11.1.1 Host Message Format
Start
Address (optional)
Body
Delimiter
CR
#
device_id@
Message
11.1.1.1 Simple Command
Command string with only one command without addressing:
Start
Body
Delimiter
CR
#
Command SP Parameter_1,Parameter_2,…
11.1.1.2 Command String
Formal syntax with commands concatenation and addressing:
Start
#
Address
Body
Delimiter
CR
device_id@
Command_1 Parameter1_1,Parameter1_2,…|
Command_2 Parameter2_1,Parameter2_2,…|
Command_3 Parameter3_1,Parameter3_2,…|…
11.1.2 Device Message Format
Start
Address (optional)
Body
delimiter
CR LF
~
Sender_id@
Message
28
VS-66HN - Protocol 3000
Download from Www.Somanuals.com. All Manuals Search And Download.
11.1.2.1 Device Long Response
Echoing command:
Start
~
Address (optional)
Body
Delimiter
CR LF
device_id@
Command SP [Param1 ,Param2 …] result
CR = Carriage return (ASCII 13 = 0x0D)
LF = Line feed (ASCII 10 = 0x0A)
SP = Space (ASCII 32 = 0x20)
11.1.3 Command Terms
Command
A sequence of ASCII letters ('A'-'Z', 'a'-'z' and '-').
Command and parameters must be separated by at least one space.
Parameters
A sequence of alphanumeric ASCII characters ('0'-'9','A'-'Z','a'-'z' and some special
characters for specific commands). Parameters are separated by commas.
Message string
Every command entered as part of a message string begins with a message
starting character and ends with a message closing character.
Note: A string can contain more than one command. Commands are separated by
a pipe ( '|' ) character.
Message starting character
'#' – For host command/query
'~' – For device response
Device address (Optional, for K-NET)
K-NET Device ID followed by '@'
Query sign
'?' follows some commands to define a query request.
Message closing character
CR – For host messages; carriage return (ASCII 13)
CRLF – For device messages; carriage return (ASCII 13) + line-feed (ASCII 10)
VS-66HN - Protocol 3000
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Command chain separator character
When a message string contains more than one command, a pipe ( '|' ) character
separates each command.
Spaces between parameters or command terms are ignored.
11.1.4 Entering Commands
You can directly enter all commands using a terminal with ASCII communications
software, such as HyperTerminal, Hercules, etc. Connect the terminal to the serial
or Ethernet port on the Kramer device. To enter CR press the Enter key.
( LF is also sent but is ignored by command parser).
For commands sent from some non-Kramer controllers like Crestron, some
characters require special coding (such as, /X##). Refer to the controller manual.
11.1.5 Command Forms
Some commands have short name syntax in addition to long name syntax to allow
faster typing. The response is always in long syntax.
11.1.6 Chaining Commands
Multiple commands can be chained in the same string. Each command is
delimited by a pipe character (“|”). When chaining commands, enter the message
starting character and the message closing character only once, at the
beginning of the string and at the end.
Commands in the string do not execute until the closing character is entered.
A separate response is sent for every command in the chain.
11.1.7 Maximum String Length
64 characters
30
VS-66HN - Protocol 3000
Download from Www.Somanuals.com. All Manuals Search And Download.
11.2 Kramer Protocol 3000 Commands
Short
Command
Form
Description
Permission
End User
#
Protocol handshaking
Read device build date
BUILD-
DATE?
End User
CPEDID
Copy EDID data from the output to the input
EEPROM
End User
End User
DISPLAY?
FACTORY
GETEDID
Read if output is valid
Reset to factory default configuration
Read EDID data
User SW Internal
User SW Internal
GETEDID-
EXT
Read EDID data from external device
connected to output
HELP
List of commands
End User
End User
End User
End User
User SW Internal
Administrator
End User
End User
End User
End User
End User
End User
End User
End User
Administrator
End User
End User
End User
End User
End User
IDV
Visual identify device
Read in/out count
INFO-IO?
INFO-PRST?
LDEDID
LOCK-FP
LOCK-FP?
MODEL?
P2000
Read maximum preset count
Load EDID data
LCK
Lock front panel
LCK?
Read lock front panel
Read device model
Switch to protocol 2000
Read device protocol version
Read saved presets list
Recall saved preset
PROT-VER?
PRST-LST?
PRST-RCL
PRST-STO
PRST-VID?
RESET
Store current connections to preset
Read video connections from saved preset
Reset device
SIGNAL?
SN?
Read if input is valid
Read device serial number
Read device firmware version
Switch video only
VERSION?
VID
VID?
Get video switch state
VS-66HN - Protocol 3000
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
For the latest information on our products and a list of Kramer distributors,
visit our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: [email protected]
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
!
2900- 300154
8
P/N:
Rev:
Download from Www.Somanuals.com. All Manuals Search And Download.
|