PSS 260
Operating
and safety instructions
ꢀ
P
N
T
G
I
E
S
GERMAN
DESIGN
PATENT
N D
O
G
F
·
2 0 0 2
Download from Www.Somanuals.com. All Manuals Search And Download.
ቨ
ቩ ቪ ቫ
ቦ ቧ
ተ
ቢ ባ ቤ ብ
ቭ
ቱ
ቮ
ቲ
ቯ
ꢁ
ꢀ
ታ
ቪ
Download from Www.Somanuals.com. All Manuals Search And Download.
PSS 260 ORBITAL SANDER
For effortless sanding of metal, wood and varnish/paint …
Dear Customer! We are delighted that you have decided to purchase our high quality PSS 260 orbital sander. Please make sure you familiarise
yourself fully with the way the equipment works before you use it for the first time and that you understand how to handle electrical power
tools correctly. Please read the operating instructions
below and the accompanying safety advice
carefully. Use the equipment
!
only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results.
We hope you enjoy using your sander.
FEATURES OF THE PSS 260
ቢ
ባ
ቤ
ብ
ቦ
ቧ
Clip
Sanding sheet
Base
Air vents
Dust bag adapter
Paper dust bag
ቨ
ቩ
ቪ
ቫ
ቭ
Handle
ON / OFF switch
Adjuster wheel
Continuous operation locking button
Dust extraction nozzle (Fig.)
ባ,ቦ,ቧ,ቭ = accessories supplied
TECHNICAL INFORMATION
Nominal power:
Low load speed:
260 W
Nominal voltage: 230 V ~ 50 Hz
Dust extraction system: built-in extraction system / or with exterior suction device
n 7,000 – 11,000/min
o
Orbits: max. approx.
Pad size:
Orbit:
Sanding sheet size max: approx.: 280 x 115 mm
Protection class: II
22,000/min
225 x 115 mm
2.1 mm
Weight:
2.25 kg
The A weighted noise level of the equipment is typically:
Sound pressure level: 70.0 dB(A)
The acceleration value is typically 2.5 m/s2 (vibration)
!
IMPORTANT SAFETY ADVICE
•
•
•
•
•
•
To be read in conjunction with the advice in the accompanying booklet on safety.
The sander is not designed for wet sanding and therefore is only to be used for dry sanding
Do not use the sander on materials containing asbestos
Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask
Take note that working with stone and wood can give rise to dusts that can damage your health.
Always keep the power cable well out of the sander's working area and fed to the rear of the machine.
OPERATION
Take note of the mains voltage. The voltage must agree with that shown on the identification plate (equipment shown as 230 V
can also be used with 220 V).
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SWITCHING ON AND OFF
When using the orbital sander you can select between continuous and non-continuous operation (see Fig. ቱ). For short periods of sanding
use the non-continuous setting and for longer periods use the continuous setting. Select your chosen setting as follows:
SWITCH ON NON-CONTINUOUS OPERATION:
SWITCH OFF NON-CONTINUOUS OPERATION:
press ON/OFF switch ቩ.
release ON/OFF switch ቩ.
SWITCH ON CONTINUOUS OPERATION:
SWITCH OFF CONTINUOUS OPERATION:
SETTING THE SPEED
press ON/OFF switch ቩ and with it still pressed fix it in place
by pressing the continuous operation locking button ቫ.
press on/off switch ቩ and release it again.
You can set the required speed using the adjuster wheel ቪ (see Fig ቱ) as required. As the setting depends on what kind of material
you are working with, use the recommendations and examples given in Tips and Tricks.
FITTING THE SANDING SHEETS
Note: before fitting a new sanding sheet, remove dust and dirt from the base ቤ.
1. Lift both clips ቢ to open them to insert a new sanding sheet or change the sanding sheet for use on a different material.
2. Push the sanding sheet ባ under the open clip at one end and clamp it securely on the base by moving the clip down again.
3. Do the same at the other end. Make sure that the sanding sheet ባ is tight against the base. See Figures ቮ and ቯ.
4. Important! - The holes in the sanding sheet ባ and the base ቤ must align for the dust to be extracted through the base. See Figure ተ.
Different materials need different grades of sanding sheets. To determine which grade is suitable for your work, please read our
recommendation in Tips and Tricks.
DUST EXTRACTION
• DUST EXTRACTION WITH PAPER DUST BAG
Push the paper dust bag ቧ on to the adapter ቦ. Ensure that the adapter fits correctly into the holder. Clip the dust bag with the adapter
to the side of the sander.
• DUST EXTRACTION WITH VACUUM CLEANER
For dust extraction using a vacuum cleaner use the appropriate connector – see Figure ቭ. Attach the adapter to the end of the vacuum
cleaner hose and clip it to the side of the equipment.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
5
MAINTENANCE OF THE ORBITAL SANDER
1. Clean the sander regularly. For the best results do this straight after the work has been completed.
2. Do not allow liquids to get inside the sander. Use a soft cloth for cleaning the housing. Do not use petrol, solvents or cleaners
that may attack the plastic.
3. Air vents must always be clear and clean.
ADVICE ON WORKING METHODS, TIPS AND TRICKS
•
•
•
•
•
You can use the PSS 260 orbital sander for effortless sanding even on large areas, see Fig. ቲ.
Move the orbital sander in parallel broad circles or in alternate longitudinal and transverse directions.
Do not press on the orbital sander. This damages the sanding sheets and adversely affects sanding performance.
From time to time clean the sanding sheet with a vacuum cleaner.
You do not have to resand any areas when working up to edges. The orbital sander works right into the corners because its housing
is continuous with the edge of the sanding sheet, see Fig. ታ.
•
The integrated dust extraction system allows you to work cleanly overhead. Use the integrated dust extraction system or your vacuum cleaner
wherever possible when sanding.
•
•
The choice of speed and grade of sanding sheet determines the sanding performance and therefore the results of your work.
Never use the same sanding sheet on different materials (e.g. wood and then metal).
•* For metals we recommend 60 grade (steel) or 80 grade (aluminium) – with a medium to high speed.
•* For wood we recommend 60 grade (hardwood) or 60 – 80 grade (soft wood) with a medium to high speed. If you are sanding veneered
surfaces we recommend 240 grade – with a low to high speed depending on the smoothness of the finish.
•* When working on varnished/painted surfaces we recommend 120 grade e.g. for smoothing out scratches (medium to high speed),
180 grade for sanding down (low speed) and 40 grade e.g. for removing rust (low to middle speed).
•
The PSS 260 orbital sander uses HIGH TECHNOLOGY FIXING.
This no-tool quick change feature allows you to work
more easily and quickly. One hand is all that is needed.
•* These are advisory recommendations only. Before you start work, you should carry out a test to see which grade and speed is
most suitable for your work.
Further practical tips for power tools can be found in the accompanying booklet on safety advice.
We reserve the right to make technical modifications in the course of further development.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
6
STATEMENT OF CONFORMITY
We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare
that this product conforms with the following EC regulations:
(98/37 EWG)
(73/23/EEG), (93/68 EEG)
(89/336 EEG), (92/31 EEG), (93/68 EEG)
EN 50144-1:1998
EC low voltage regulations:
Electromagnetic compatibility:
Applicable harmonised standards:
EN 50144-2-4:1995
EN 55014-1:1993+A1
EN 61000-3-2:1995+A1+A2
EN 61000-3-3:1995
EN 55014-2:1997
Type: PSS 260
Bochum, 30.06.2002
Hans Kompernaß
- Managing Director -
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
7
WARRANTY
This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of
care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its
original packaging with the proof of purchase (if available) to the closest service address.
Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty.
ꢀ
Beaver Electronic Services · The Lodge, Premier Business Park
Long Street, Walsall · West Midlands, WS2 9DY
Tel.: 01922/725554 · Fax: 01922/725417
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
© manual design, photos, translations by
ORFGEN Marketing & Communication
Essen · Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
|