TECHNICAL INFORMATION DATA SHEET
CCPR11
Revised 7-04
Copyright, Eastman Kodak Company, 2004
CURRENT COLOR PRINTER RECOMMENDATION: BLACK-AND-
WHITE PRINTING / MONITOR MODE
Printing on KODAK PANALURE SELECT RC Paper Using the KODAK
ACCUDATA Printer Controller XL or The KODAK Digital Printer
Controller
1) General Information
General Setup Information
Note: CCPR VALUES ARE NOMINAL. THEY SHOULD BE USED AS A STARTING POINT FROM WHICH
CUSTOMERS MAY OPTIMIZE THEIR ANALYZER/PRINTER SYSTEM BASED UPON THE PLANT'S FILM
POPULATIONS.
KODAK PANULURE SELECT RC Paper is designed for making black-and-white prints from color negatives.
Following are some setup recommendations for printing negatives on L, M, or H paper grades using the KODAK
ACCUDATA Printer Controller XL or the Kodak Digital Printer Controller (DPC).
Use the nominal CCPR values as a starting point to optimize your printer.
•
•
•
Install a 1/16-inch 2337 acrylic plastic diffuser in the negative mask plate.
Use a 600-watt FFJ printing lamp.
Use a KODAK Neutral Cold Mirror, Notched (CAT No. 147 9005) for the VCL lamphouse or a KODAK Neutral
Cold Mirror (VCB) (CAT No. 110 3795) for the VCB lamphouse.
•
Use a KODAK PROFESSIONAL PORTRA Normal Negative (Size 120, CAT No. 846 0948), or a KODAK
PROFESSIONAL PORTRA Printer Control Negative Set (Size 135, CAT No. 179 8511) to adjust and control the
printer balance.
•
•
Use a starting print density on 0.60 on the normal gray patch of the Normal Control Negative.
Use a dead heat setup time of 0.70 seconds.
Recommended Starting Lens Diaphragms:
L Contrast Grade
M Contrast Grade
H Contrast Grade
312 Upper Track
G crop to 8 x 10
38
32
35
44
38
41
60
51
56
312 Lower Track
G crop to 5 x 7
DCP-8 Printers
G crop to 8 x 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Sheet—3
Copyright, Eastman Kodak Company, 2004
CCPR11 Revised 7-04
KODAK Digital Printer Controller (DPC)
•
•
•
•
•
Starting BFA = 0, 0, 0 (all filtration dialed out).
PR # = 0
Set SPG = 25
Set BIC = 75, -100
Set NEU and NEO = 110, 110, 110, for L and M grade papers.
Set NEU and NEO = 100, 100, 100, for H grade paper.
Set FILTER FACTORS to:
1, 1
1, 2
1, 3
2, 1
2, 2
2, 3
3, 1
3, 2
3, 3
0
100
100
100
0
100
100
100
0
Printing Density Matrix Values
1, 1
2, 1
3, 1
1, 2
2, 2
3, 2
1, 3
2, 3
3, 3
-244
0
0
0
-244
0
0
0
-244
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Sheet—4
Copyright, Eastman Kodak Company, 2004
CCPR11 Revised 7-04
Lamphouse Information
Addition of lamphouse BFA filtration or color-button correction will affect the print density of the original scene colors
as follows:
Lamphouse Filtration Added
Density Change Scene Color
+C
R
+
G
-
B
-
C
-
M
+
Y
+
+M
R
-
G
+
B
0
C
+
M
-
Y
0
+Y
R
0
G
0
B
0
No Apparent Change
C
0
M
0
Y
0
Note: The addition of lamphouse filtration will increase printing times and is not recommended.
Responsibility for judging the applicability of this information for a specific use rests with the end user.
The contents of this publication are subject to change without notice.
Kodak, Kodak Professional, Accudata, Panalure, and Portra are trademarks.
Kodak Professional Division
EASTMAN KODAK COMPANY - Rochester, NY 14650
End of Data Sheet
Download from Www.Somanuals.com. All Manuals Search And Download.
|