Kameleon
HDP6000
1080p DLP™ Projector
Users‟ Manual v1.1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TABLE OF CONTENTS
Safety Warnings
Introduction
Positioning the projector
Choosing the aspect ratio
4
5
8
9
Video connectors
Connecting a video device
10
10
10
10
10
10
Composite (RCA) video connection
S-video connection
Component (RCA) connection
SCART RGB connection
Digital connections
10
10
10
DVI connection
HDMI connection
Computer connections
RS-232 connections
11
11
Displaying an image
Adjusting the image
Shutting down the projector
11
11
12
Troubleshooting your setup
13
Using the remote control
Using the keypad buttons
Optimizing video images
Customizing the projector
17
18
19
19
Using the menus
Picture menu
19
20
22
Settings menu
Maintenance
24
24
25
Cleaning the lens
Replacing the projection lamp
RS-232 terminal specs
Warranty Information
26
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Important Operating Considerations for Safety
Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 8 degrees off axis.
• Locate the projector at least 4' (1.2m) away from any heating or cooling vents.
• Do not block ventilation openings. Locate the projector in a well ventilated area without obstructions to
intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block
the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector
may come into contact with smoke or steam.
• Do not touch the exhaust vents. This area will become hot while the projector is being used. Be sure
children are kept away from this area.
• Do not look directly into the lens while the projector is being used. Be especially careful that children do not
stare directly into the lens.
• Do not push objects of any kind into this projector through its venting as object may touch dangerous
voltage that could result in a fire or electrical shock.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the projector.
• Do not place any object on the projector.
• Do not stand or step on the projector.
• Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth)
ground terminal. The AC power cord has a three-pin grounding-type power plug. This plug will only fit a
grounding-type power outlet. This is a safety feature. Do not remove the grounding pin on the power plug.
A surge-protected power strip is recommended. Do not overload wall outlets.
• When disconnecting the power cord, hold the plug, not the cord. Unplug the projector from the wall outlet, if
the projector is unused for an extended time.
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries polarity (+/-) is aligned correctly.
Dispose of used batteries in accordance with local disposal laws.
• Use a Knoll approved ceiling mount kit for proper fitting, ventilation and installation. The projector warranty
does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper
location.
• When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp
door.
• The projector must be installed by a qualified professional in order to ensure proper operation and reduce
the risk of hazards or injury. It is not recommended you install the projector yourself.
• Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and
will void the warranty.
• Only use replacement parts specified by Knoll. Unauthorized substitutions may result in fire, electrical
shock, or injury, and may void the warranty
• Only genuine Knoll lamps are tested for use in this projector. Use of non Knoll lamps may cause electrical
shock and fire, and may void the projector warranty.
• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture
with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also
increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
In the unlikely event of a lamp rupture, particles may exit through the projector vents. Keep people, food,
and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
• When the power cord or plug is damaged or frayed
• If liquid has been spilled into the projector
• If the projector has been exposed to rain or water
• If the projector does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as improper adjustment of other controls may result in
damage and may required extensive work to restore the projector to normal operation
• If the projector has been dropped
• When the projector exhibits a distinct change in performance, this indicates a need for service.
Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to
follow these instructions may affect the warranty.
Introduction
Congratulations and thank you for your choice of a superior digital image projection device. Your
new Knoll projector is specifically designed for home cinema applications. The projector sets a
high standard using the latest DLP™ technology and new DNX video processing from
Pixelworks™. This projector has 1920 x 1080 resolution (1080p). Whether you are watching
movies or High Definition broadcasts or playing the latest video game, you will enjoy amazing
image quality. The unique design and color of the projector make it a welcome addition to your
home.
keypad
Top cover
Lens
Lamp Access
Receiver (IR)
Product specifications
specifications are subject to change.
dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Power
S-Video HDMI
RS232
VGA
Rear Connector Panel
USB
12 VDC triggers
Composite video
Component video
Wired remote
The projector provides the following connection options:
• VGA computer.
• Two HDMI™ (High Definition Multimedia Interface)
• Three Component Video (RCA)
• S-video
• Composite video (RCA)
• USB port
The projector also provides the following connectors:
• RS-232 for serial control
• 12-volt DC output (see below)
Three 12-volt DC outputs
The 3.5mm mini-jack trigger provides a 12-volt, 0.25 amp DC output. It provides a constant output
while the projector is on. It has numerous uses. For example, if you connect your projection
screen to the 12-volt DC output with the cable that came with your screen, when you turn on the
projector the screen will move down; when you turn the projector off, the screen will return to the
storage position.
12V+
ground
3.5mm plug 12VDC output
screen relay (see screen
manufacturer for details)
The “Lamp” trigger turns on when the lamp is lighted. If you connect your projection screen to this
output using the cable that came with your screen, the screen will move down when the lamp is
turned on and the screen will return to its storage position, when the lamp is turned off.
The Letterbox “1” and “2” triggers are active when the projector is placed in letterbox mode and
are utilized for variable masking and anamorphic lens control. (These triggers are off when
SplitScreen is active.)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Setting up the Projector
There are a number of factors to consider when determining where to set up the projector,
including the size and shape of your screen, the location of your power outlets, and the distance
between the projector and the rest of your equipment. But here are some general guidelines.
NOTE: To ensure adequate cable access, do not place the
projector within 6 inches (0.15 m) of a wall or other object.
Position the projector on a flat surface (either on a table or ceiling mounted) at a right angle to the
screen at least 1.5m (4.9‟) from the projection screen.
The projector should be within 10 feet (3 m) of your power source and within 6 feet (1.8 m) of
your video source(s), unless good quality extension cables or baluns are to be used.
When installing the projector on the ceiling, refer to the installation guide that comes with the
Ceiling Mount Kit for more information. Knoll recommends use of the CM33 mount shipped with
the projector or the deluxe swivel ceiling mount. The addition of a CM20+6 extension bar lowers
the projector 6” per bar as required. The CM25EX is an adjustable extender that can lower the
projector 6.75” to 11” (17-28 cm). The ceiling mount kit may be sold separately.
Position the projector the desired distance from the screen. The distance from the lens of the
projector to the screen, the zoom setting, and the video format determine the size of the projected
image.
If the image is square but not centered on the screen or viewing area, adjust it by using the lens
shift dials. Use the Horizontal dial to shift the lens left or right. Use the Vertical dial to shift the lens
up or down.
NOTE: As the lens is shifted away from the lens centerline, the horizontal shift range is
reduced. To adjust lens shift efficiently we suggest you follow these steps:
1 Use vertical lens shift to move the image closer to the lens centerline than the final vertical
position.
2 Use horizontal lens shift to determine the center horizontal position, then move image to
the center horizontal position. Maximum horizontal offset +/-15%.
3 Use vertical lens shift to move the image away from the lens
centerline to the final vertical position.
4 Use horizontal lens shift to move the image to the final horizontal
position.
5 If lens shift is unable to move the image far enough, move the
projector (preferable) or tilt the projector and then use vertical and
horizontal keystone to re-position the image.
•
The vertical image offset range is 105%~130% for the HDP6000
(default for is 105%). The default horizontal image offset is +/-15%,
however at maximum vertical image offset, there is no horizontal
lens shift.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Projector Positioning
The projected image becomes larger as the distance between the unit and screen increases.
The manual zoom allows the distance from the screen to be within a minimum and maximum
range. See the chart on the next page for details. The example below defines the screen height,
width, diagonal, etc.
HDP6000 Projection Throw Distance 16:9 Video Screen:
Screen Diagonal
Minimum Distance
Maximum Distance
Viewing Area
92"
103"
135"
204"
106"
139"
209"
110"
145"
217"
122.5"
161"
146.75"
193"
121"
183"
242"
290"
45"x80" 50.5"x89.75" 52"x92" 54"x96" 60"x107" 72"x128"
MAXIMUM DISTANCE TO SCREEN (16:9) = 1.98 x SCREEN DIAGONAL SIZE
MINIMUM DISTANCE TO SCREEN (16:9) = 1.31 x SCREEN DIAGONAL SIZE
An interactive screen calculator (in Microsoft Excel format) is available at:
Anamorphic Lens
Please note the HDP6000 is designed for use with 16:9 screens. They also have a
built in scaler for use with 2.35:1 screens. To display images at the highest
definition possible in 2.35:1 or cinemascope (most major movies are filmed in
2.35:1) an anamorphic lens is required. We recommend the Panamorph brand,
which has fixed, movable and motorized anamorphic lens for use with the
HDP6000.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Choosing the aspect ratio
Aspect ratio is the ratio of the image width to
image height. HDTV and most DVDs are 16:9,
which is the default for this projector. When in
4:3 mode the projector places black bars on
both sides of the image. Native mode centers
the image and turns off the internal scaler so
that any resolution larger than the native
projector resolution is cropped on the edges.
Letterbox expands the image to fill the screen.
What you plan to project will also help you
choose between 4:3 and 16:9. For example,
most low definition TV shows are 4:3, while
most movies are 16:9. If you have a 16:9
screen, then you should select an aspect ratio
of 16:9 for anamorphic movies and HDTV, and
Native for 4:3 content. If you have a 4:3 screen
you should still use 16:9 for anamorphic movies
or HDTV, but you also have the option of using
4:3, Native, or Natural Wide for 4:3 content.
Keep in mind that anamorphic movies only
appear correctly if the DVD player is set to
output to a 16:9 television. Natural Wide
stretches a 4:3 image to fill the entire 16:9
screen. The center two-thirds of the image is
unchanged; the edges of the image are
stretched.
Cable Management
The HDP6000 features an integrated
cable management system that allows
you to keep the cables organized. To
use the cable management system,
thread the cables into the slots as
shown in the illustration.
Video Quality
The first step for connecting video is determining what type of output connectors your source
video device has. If there is more than one output, select the one with the highest quality. The
best quality ranking, with 1 being the highest, is:
1. HDMI.
2. Component (RCAs)
3. S-video
4. Composite Video (RCA)
If your device has a VGA connector, you can use the VGA connector for a high-quality image.
Many PC game systems have VGA connectors.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video
game consoles, HDTV receivers, and TV tuners to the projector. Connect the audio from your
video device to your stereo system to get sound. You can connect the projector to most video
devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a cable or
satellite company; the signal must pass through a tuner first. Examples of tuners are digital
cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can
change channels is considered a tuner.
An HDMI cable is provided with your projector so you can quickly and easily connect a video
source to the projector and see the amazing image that is displayed. Once you have determined
a more permanent location for your projector, we recommend purchasing higher quality cables in
the proper length to get the best image from your particular video equipment.
Composite (RCA) video connection
Plug the composite video cable‟s yellow connector into the video-out connector on the video
device. Plug the other yellow connector into the yellow Composite connector on the projector.
S-video connection
If your video device uses a round, four-prong S-video connector, plug the S-video cable into the
S-video connector on your video device and into the S-video connector on the projector.
Component (RCA) connection
If your device uses component connectors, plug a component video cable with red, green, and
blue RCA connectors into the source device‟s component connectors and the Component
connectors on the projector. The HDP6000 has three component video inputs. Be sure to use
the remote control to select the correct component input.
Digital connections
The two HDMI (High-Definition Multimedia Interface) connectors are digital and yield the highest
quality image. It is common for these signals to be encrypted with HDCP (high-band width digital-
content protection). Your new projector ships standard with decryption codes so you can enjoy
these high quality, all digital images.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface
between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an
HDMI cable into the video-out connector on the video device and into the HDMI connector on
the projector. To display HDMI with its deep color and 30-bit detail, a HDMI source is needed.
Please note the HDP6000 has no audio capabilities at all. The HDP6000 has two HDMI video
inputs. Be sure to use the remote control to select the correct HDMI input.
Please note that the projector has no audio capabilities, so audio signals transferred through
HDMI will not be audible.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Computer connections
You can connect a computer‟s VGA connector to the VGA input on the projector using a VGA
cable.
RS-232 connections
You can control the projector from an LCD control panel or computer by connecting an RS-232
cable to the projector‟s Serial control connector.
Displaying an image
Connect the power cord to the Power connector cord
plug in power
on the back of the projector and to your electrical outlet.
NOTE: Always use the power cord that shipped with the projector.
Press the Power button on the remote control.
The LED blinks green and the fans start to run.
press power button
When the lamp comes on, the start-up screen is displayed
and the LED is steady green. It can take a minute for the
image to achieve full brightness.
? No start up screen? Get help on page 13
Plug in, connect, and turn on your video device.
The video device‟s image should appear on the
projection screen. If it doesn‟t, press the Source button
on the remote until the image appears.
turn on video device
If you are using a laptop the VGA output may have to
Be enabled to view an image.
Adjusting the image
Adjust the image by tilting the projector up or down
adjust height
Position the projector the desired distance from the screen at a 90-degree angle to the screen.
See page 8 for a table listing screen sizes and distances to the screen.
Remove the top front lid.
a. Slide the tabs on the side toward the rear of the projector to unlock
the projector top cover.
b. Slide the top toward the front of the projector to unhook it from the
projector body.
c. Lift off.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Adjust the focus and zoom.
If the image is square but not centered
adjust it using the lens shift dials.
adjust focus
adjust zoom
horizontal lens shift
vertical lens shift
Rotate the elevator feet if needed for granular adjustment of the projector‟s height. Avoid placing
your hands near the hot exhaust vent at the side of the projector.
Adjust the Contrast or Brightness in the Basic Picture menu.
Adjust the volume on your stereo receiver.
adjust volume
Your projector has been factory optimized for
excellent performance no matter what the source.
However, if you wish to make further changes you
can optimize the image using on screen menus.
adjust Picture menu options
including Aspect Ratio
Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio
in the Picture menu. See page17 for help with the menus and these adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in order to view the
highest quality image. For more information regarding Aspect Ratio, see page 9.
Shutting down the projector
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning on the Screen
Save Time feature in the Setup menu...
Auto Off Time
The projector has an Auto Off Time feature that automatically turns the projector off if no active
sources are detected and no user interaction with the projector is performed for 30 minutes. By
default, this feature is off. You can change the length of time.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The lamp turns off and
the LED blinks amber for 10 seconds while the fans continue to run to cool the lamp. When the
lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely
power off the projector.
NOTE: Once the projector has been turned off, you must wait for one minute before turning the
projector on again. This allows the lamp to properly cool and extend the lamp life up to 3000
hours). The LED light is solid green when the cooling process is complete.
NOTE: The biggest cause of early lamp failure is not allowing the lamp to cool properly, either
from power failures or disconnecting power to the projector before the fan can cool the lamp
properly.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot
the setup. The LED on top of the projector indicates the state of the projector and can
help you troubleshoot.
The status indicator on the top of the projector can help you diagnose any problems the projector
is experiencing.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
The following tables show common problems. In some cases, more than one possible solution is provided.
Try the solutions in the order they are presented. When the problem is solved, you can skip the additional
solutions.
Problem
No startup screen
Solution
Plug in power and press the
Result
Correct_image
power button.
Computer image
projected
Only start up screen appears
Press the start button and
activate the laptops external
port. Restart laptop
No computer image, just the
words “Signal out of range”
Press the Auto Image button on
the remote. Adjust computer
resolution and refresh rate.
Control Panel>Display>Settings
>Advanced>Adapter
Computer image
projected
Only my laptop’s background
Windows-Disable “Extend my Background and Desktop
appears, not the desktop icons
Windows Desktop” in Control projected
Panel>Display
>Settings>
Display 2
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Still need assistance?
during Pacific west coast time. This product is backed by a limited warranty. An extended
warranty plan may be purchased from your retailer or dealer.
When sending the projector in for repair, we recommend shipping the unit in its original packing
material, or having a professional packaging company pack the unit. Please insure your shipment
for its full value.
Using the remote control
The remote uses two provided AA batteries. They are easily
installed by sliding the cover off the remote‟s back, aligning the
+ and - ends of the batteries, sliding them into place, and then
replacing the cover.
To operate, point the remote at the projection screen or at the
front of the projector (not at the video device or computer). The
range of optimum operation is up to 30 feet (9.14m).
Press the remote‟s Menu button to open the projector‟s menu
system. Use the arrow buttons to navigate, and the Select button
to select features and adjust values in the menus
The remote also has:
• Power button to turn the projector on and off (page 12 for
shutdown info)
• Help button to access the projectors help feature
• Source buttons to switch among sources
• Resize button to change the Aspect Ratio
• Auto Image button to resynchronize the projector to the source
• Preset button to select stored settings (see page 18)
• Overscan button to remove noise at the edge of a video image
• Custom button that can be assigned to a special function, like Blank Screen or Freeze
• Source 1, 2, 3 switches between user assigned sources.
Troubleshooting the remote
• Make sure the batteries are installed properly and are not dead.
• Make sure you‟re pointing the remote at the front of the projector or at the screen, not at the
video device or the computer, and are within the remote range of 30 feet (9.14m).
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their
functions:
Power–turns the projector on and off (page 12).
Auto Image–resynchronize the projector to the source.
Presets–cycles through the available preset settings.
Menu–opens the onscreen menus.
Select–confirms choices made in the menus.
.
Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus
Source–changes the active source.
Help–button to access the projector‟s help feature
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the image using
the onscreen menus.
•
•
•
•
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
Change the Aspect Ratio. Choose the option that best fits your input source.
.
Adjust the Color Temperature in the Advanced Picture menu
Advanced Picture menu.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Once you have optimized the image for a particular source, you can save the settings using
Presets. This allows you to quickly recall these settings later.
Presentation features
Several features are provided to make giving presentations easier. Here is an overview, details
are found in the menu section.
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
projector and current source.
•
•
The Search Screen option lets you change the appearance of the blank screen and start up
screen.
Two options, Auto Off and Screen Save Time, are provided to automatically shut down
the projector after several minutes of inactivity or display a black screen. This helps
preserve lamp life.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Optimizing video images
Your projector has been factory optimized for very good performance no matter what the source.
However, if you wish to make further changes you can optimize the image using onscreen
menus.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu.
• Select a Sharpness setting.
• Use the Color Control to adjust the color gain and offset.
• Adjust the Color Temperature. Select a listed value.
• Turn on Overscan to remove noise on the edges of the video image.
• Change the Aspect ratio. Aspect ratio is the ratio of the image width to image height. Low
resolution TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or
16:9 (the projector‟s default). Choose the option that best fits your input source in the menus, or
press the Resize button on the remote to cycle through the options.
• Select a specific Color Space.
• Select a different Video Standard. Auto tries to determine the standard of the incoming video.
Select a different standard if necessary.
• Make sure your DVD player is set for a 16:9 television. See your DVD player‟s user‟s guide for
instructions.
Customizing the projector
You can customize the projector for your specific setup and needs. See page 18 to page 21 for
details on these features.
• For rear projection, turn rear mode on in the Settings>System menu.
• For ceiling mounted projection, turn ceiling mode on in the Settings> System menu.
• Turn the projector‟s display messages on and off.
• Turn on power saving features.
• Specify blank screen colors and start up logos.
• Specify the language viewed on the menus.
• Save the settings for the active source as a preset.
Using the menus
To open the menus, press the Menu button on the keypad or remote. The menus automatically
close after 60 seconds if no buttons are pressed.
The Main menu appears. Use the arrow buttons to move up and down to highlight the desired
submenu, then press the Select button.
To change a menu
setting, highlight it, press
Select, then use the arrow
buttons to adjust the
value or select an option
or turn the feature on or
off. Press Se
l
e
c
t
to
confirm your changes.
Use the arrow buttons to
navigate to another
setting. When your
adjustments are
complete, press Menu to
access a different menu;
press the Menu button at
any time to navigate to
the higher-level menu and
ultimately close the
menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
The menus are grouped by usage:
•
•
•
•
The Basic Picture menu provides common image adjustments.
The Advanced Picture menu provides more complex image adjustments.
The Setup menu provides set-up type adjustments that are not changed often.
The Status and Service menu provides information about the projector and source.
Basic Picture menu
To adjust the following settings, highlight the setting, press select,
use the arrow buttons to adjust the values, then press Select to
confirm the changes.
Brightness Changes the intensity of the image.
:
Contrast: Controls the degree of difference between the lightest and
darkest parts of the picture and changes the amount of black and
white in the image.
Sharpness: Changes the clarity of the edges of a video image. Select a sharpness setting.
Color: Adjusts a video image from black and white to fully saturated color. The color setting
applies to video sources only.
Tint: Adjusts the red-green color balance in the image of NTSC video images. The tint
setting applies to NTSC video sources only.
SplitScreen: Allows two distinct sources to be displayed simultaneously. Switch primary
sources, make picture adjustments and choose one of multiple display options: either two side
by side horizontal or vertical source regions or a small secondary source image displayed on top
of the primary source in one of four placement options.
Auto Image
:
Forces the projector to reacquire and lock to the input signal. This is useful when
signal quality is marginal.
Aspect Ratio: Aspect ratio is the ratio of the image width
to image height. Low resolution TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio.
Choose Native to see the unmodified input with no
resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
Apply Preset: Presets are provided that optimize the projector for displaying computer
presentations and video images under certain conditions.
There is also a user-definable preset. To set this preset, adjust
the image and select Save User in the Presets menu. You can
recall these settings in the future by selecting the User preset.
Horz/Vert Keystone: Adjusts the image horizontally and
vertically and makes a squarer image.
Digi
ta
l
Zoom: Changes the size of projector‟s display area. If
the display area has been resized by this setting, it can be
moved by changing the Horz Shift and Vert Shif settings.
t
Horz Shift/Vert Shift Moves the display area horizontally or
:
vertically if its size has been changed by the Digital Zoom setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Advanced Picture menu
BrilliantColor™: Produces an expanded onscreen color
spectrum that delivers enhanced color saturation for bright,
true-to-life images. Choose Normal Look for most video
sources and Bright Look for most computer sources.
Iris/DynamicBlack Select Auto to constantly adjust the
:
aperture based on the amount of black in the current scene, or
select a percentage for a fixed aperture size (100% is
maximum size).
Color Temperature: Changes the intensity of the colors.
Select a listed relative warmth value.
Force Wide: When this is off, the analog locking algorithms choose the standard mode
resolution (4:3) as the preferred default resolution. When this is on, the analog locking
algorithms choose wide mode resolution (16:10) as the preferred default resolution.
Overscan: Removes noise around the video image.
Phase: Adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player, is not
syncing properly with the projector, select this option to help it to sync when connected to the
projector.
Tracking Adjusts the vertical scan of a computer source.
:
Color Space: This option applies to computer and component video sources. It allows you to
select a color space that has been specifically tuned for the input signal. When Auto is selected,
the projector automatically determines the standard. To choose a different setting, turn off Auto,
then choose RGB for computer sources or choose either REC709 or REC601 for component
video sources.
Noise Reduction: Reduces temporal and/or spatial noise in the image.
Flesh Tone Correction: Controls the amount of flesh tone correction applied to the image.
Black Level Analyzes the current input image and calculates an offset value which is then
:
added to the analog to digital converter black level value. This ensures optimum black level for
each analog source.
Detect Film: Controls film mode detection, and determines whether the original source of
the input video was film or video.
CRT.
Gamma: Select the appropriate gamma from among Video, Film, Bright, and
Color Gamut: Sets the color gamut of the input signal.
Color Gain: Adjusts the gain of the red, green, or blue channel of the image.
Color Offset: Adjusts the offset of the red, green, or blue channel of the image.
Horizontal/Vertical Position: Adjusts the position of a computer source.
Horizontal/Vertical Pincushion Correct optical pincushion distortion.
:
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Setup menu
Language Allows you to select a language for the onscreen display.
:
Key Click: Turns the key click sound on or off. When this setting is on, pressing keys on the
keypad causes the projector‟s speaker to play a “click” sound.
Custom Key
:
Allows you to assign a different function to the Custom button, allowing you to
quickly and easily use the effect. Highlight an effect and press Select to choose a different one.
•
•
•
•
•
•
•
•
•
•
Source Info: The default action. Shows the Source Info menu.
Projector Info: Shows the Projector Info menu.
Aspect Ratio: Sets the ratio of image width to image height.
Auto Image: Resynchronizes the projector to the source.
Overscan: Removes noise around the image.
Blank Screen: Displays an empty screen.
Freeze Screen: Pauses the projected image.
Source: Cycles through available sources.
Closed Caption: Enables or disables Closed Captioning.
SplitScreen: Enables or disables SplitScreen. Before using this for the first time, configure
SplitScreen sources and layouts using the SplitScreen menu
Source Key Enable
:
Enables or disables Source Keys on the
Commander-2 remote.
optional
AC Power On: When this feature is on, the projector
automatically turns on when electrical power is connected. This
allows control of ceiling mounted projectors with a wall power
switch.
Auto Off Time: Automatically turns the projector off after no
signals are detected for a preset number of minutes. If an active
signal is received before the projector powers down, the image
will be displayed.
Screen Save
Time: Automatically blanks the screen with a black color after no signals are
detected for a preset number of minutes. The image returns when an active source is detected or
a remote or keypad button is pressed.
Sleep Timer: Allows the projector to automatically power off after it has been on for a specified
amount of time.
Always-On Functions: Allows you to control which projector functions will work even when the
projector is in standby (powered off but connected to AC Power). Press Up or Down to highlight
the function you want to change, then press select or left and right to change the function to
either Yes or No. Press menu when done. Note that some functions must always have the
same value; in this case when you change one value, other values in the submenu may also
change automatically.
Lamp High Power: Toggles between on and off. Turn it on to raise the light output of the lamp.
This also raises the fan speed, making the projector louder. Default is off.
Power Sounds: Controls whether the projector makes a sound when powered on & off.
Auto Source: When this feature is on, the projector automatically finds the active source,
checking the selected Power-up Source first. When this feature is off, the projector defaults to
the source selected in Power-up Source. To display another source, you must manually select
one by pressing the Source button on the remote or keypad.
Power-up Source: Determines which source the projector checks first for active video
during power-up.
HDMI DDC: When this feature is set to on, the projector will support and older DVD player for
HDMI port.
Fast Color Refresh: Changes the color wheel speed from 4x to 6x.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
V
ideo Standard: When this feature is set to Auto, the projector attempts to automatically pick
the video standard based on the input signal it receives. (The video standard options may vary
depending on your region of the world.) If the projector is unable to detect the correct standard,
the colors may not look right or the image may appear “torn.” If this happens, manually select a
video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Closed Captions: Controls closed caption display while audio is not muted. If this setting is not
off, and audio is not muted, and the source is NTSC and contains captions on the selected
channel, then the projector must display caption text overlaid on the image.
Ceiling Mount: Turns the image upside down for ceiling-mounted projection.
Rear Project: Reverses the image so you can project from behind a translucent screen.
Prevent PC Screen Saver: Prevents your computer from going into Screen Save mode. The
projector must be connected to the PC via a USB cable for this feature to work.
Search Screen: Allows you to display one of the following options instead of the default screen at
startup, and when no source is detected. Options include the factory logo screen, a custom
Snapshot, or a blue, black or white screen.
Take Snapshot Captures the current image and allows it to be used as the search screen
:
image.
Disable Snapshot: Allows the user to disable the snapshot capability.
Show Messages Displays status messages (such as “Searching”) in the lower- left corner of the
:
screen.
Menu Offset: Allows you to change the position of the On Screen Display items.
Menu Transparency: Allows you to change how much of the projected image behind the menu
you can see. As the value increases, more of the image behind the menu is visible.
Magnify Controls: Allows you to change the function of the arrow buttons when the menu is not
shown. By default, the arrow buttons allow you to advance slides while in PowerPoint‟s
SlideShow mode. To make the arrow buttons also adjust magnify settings, choose Magnify
Controls to turn magnify controls on. Now when the menu is not shown, you can press the Select
button to switch between the magnification settings (Magnify Level, Magnify Horizontal Position
and Magnify Vertical Position), then press Select again to turn off magnify controls and use the
arrow buttons to advance slides.
Keypad Enable
:
Enables or disables keypad.
Glow Ring Controls the brightness level of the glow ring status indicator.
:
Serial Port, Baud Rate: Selects the serial port and baud rate.
Serial Port Echo: Controls whether the serial port echoes characters.
Status and Service menu
Source Info: Displays current source settings (read-only).
Projector Info: Displays current projector settings (read-only).
Reset Lamp Hours: Resets the lamp hours used counter in
the Projector Info menu to zero. Do this only after changing
the lamp.
Factory Reset: Restores all settings to their default.
Service Code: Only used by authorized service personnel.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Help
Press Help (on the keypad or remote) at any time to
get interactive help for solving common, picture, sound,
and cabling problems.
NOTE: The projector can be re-programmed to display a custom (non- interactive) screen
when Help is pressed. To do this: Create your custom screen on a computer and display it on
the projector, then use the Take Snapshot command in the Setup menu. When you see the
Snapshot Successful message, hold down the Help button until the message is removed.
Maintenance
Cleaning the lens
1 Turn the projector off and unplug the power cord.
2 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of
cleaner, and don‟t apply the cleaner
directly to the lens. Abrasive
cleaners, solvents or other harsh
chemicals might scratch the lens.
3 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•
•
•
Turn the projector off and unplug
power cord before cleaning any part
of the projector.
Do not open any cover on the
projector, except the lamp cover
or projector top cover.
Do not attempt to service this
product yourself as opening and
removing covers may expose
you to dangerous voltage and
other hazards. Refer all servicing
to qualified service personnel.
Replacing the projection lamp
The lamp hour‟s timer in the Service Infomenu counts the number of hours the lamp has been in
use. Twenty hours before the lamp life expires a message appears on the screen at startup
indicating that you should change the lamp. The LED on the top of the projector also blinks red
twice to indicate that the lamp should be changed. Use only a replacement lamp with the same
type and rating as the original lamp. Lamps can be purchased direct from Knoll or the dealer that
sold the projector.
Low cost on-line sales of lamps can be very costly as they sometimes cause a lot of
projector damage when used.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
WARNINGS
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it
may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp
failure or rupture also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
•
•
•
•
To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can obscure projection
sharpness and may cause the glass to shatter.
•
Be extremely careful when removing the lamp housing. In the unlikely event that the lamp
ruptures, small glass fragments may be generated. The lamp module is designed to contain
most of these fragments, but use caution when removing it.
•
•
•
Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning
materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to
prevent eye injury.
Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See
Lamp replacement procedure
1 Turn off the projector and unplug the power cord.
If ceiling mounted, disconnect all cables and
detach the projector from the ceiling mount.
2 Wait 60 minutes to allow the
projector to cool thoroughly.
3. Remove the lamp door by removing
the screws on the side of the lamp door
and lifting the door off.
4. Loosen the captive screws that attach the lamp housing
to the projector.
5. Using the handle, carefully remove the lamp housing.
Dispose of the lamp in an environmentally proper way.
6. Install the new lamp housing pressing the lamp into place.
7. Tighten the captive screws.
8. Replace the lamp door and tighten both screws
9. Plug in the power cord and press the Power button to turn the projector back on.
11. To reset the lamp hour timer, navigate to the Status and Service menu and select Reset
Lamp Hours.
Using the Security Lock
The projector has a security lock for use with a
Cable Lock System. Refer to the information that came
with the lock for instructions on how to use it.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
RS-232 terminal specifications
Communication configuration
To control the projector from and LCD control panel, connect RS-232 cable to the serial control
connector on the projector and set your computer‟s serial port settings to match this
communication configuration.
Setting
Value
Bits per second
Data bits
115,200
8
Parity
Stop bits
None
1
Flow control
Emulation
None
VT100
RS232 COMMAND FORMAT
All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses.
The request can be a read request (indicated by a “?”) or a write request (indicated by 1 to 4
ASCII digits).
A read request format (AAA?) where
(
starts the command
denotes the command
denotes the read request
ends the command
AAA
?
)
A read command returns the range and the current setting, for example:
Function
Command
Response
Brightness
Lamp hours
(BRT?)
(LMP?)
(96-160, 128)
(0-32766, 42)
A write request example: (AAA####) where
(
starts the command
denotes the command
AAA
#### denotes the value to be written (leading in zeros not necessary)
ends the command
)
Some commands have ranges, while others are absolute. If a number greater than the maximum
range is received, it is automatically set to the maximum number for that function. If a command
is received that is not understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on.
The one exception is the Power command, where 0 is off and 1 is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Function
Command
Response
Brightness
Power
(BRT10)
(PWR0)
(PWR1)
Sets brightness to 10
Turns power off
Power
Turns power on
Error Conditions
Not all commands are supported for all projectors. If an unsupported command is issued, the
command will be ignored. If a command is received that is not understood, a „?‟ character will be
returned indicating the command was not understood.
Limitations
The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must
occur between commands to ensure that the command gets properly executed. To assure the
projector can process a command, wait 3 seconds before entering the next command.
The Step column refers to increasing or decreasing the menu bar position since the On-screen
Display is not an exact match of values. For example, Step 2 changes the data by 2 through the
CLI (Command Line Interface). The menu bar is up (or down) by 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
SplitScreen Compatibility
SplitScreen allows two distinct sources to be displayed simultaneously. Switch primary sources,
make picture adjustments and choose one of multiple display options: either two side by side
horizontal or vertical source regions or a small secondary source image displayed on top of the
primary source in one of four placement options lets you show two different sources at the same
time. The following source combinations are supported:
Download from Www.Somanuals.com. All Manuals Search And Download.
32
LIMITED WARRANTY
Knoll Systems, Inc. (“Knoll”) warrants that each HDP6000 (“the Product”) sold hereunder will conform to and
function in accordance with the written specifications of Knoll. Said limited warranty shall apply only to the first
person or entity that purchases the Product for personal or business use and not for the purpose of distribution or
resale. Said warranty shall continue for a period of two (2) years from the date of such purchase. The standard
limited warranty excludes the lamps in projectors after six months and the accessories after one year. Knoll does
not warrant that the Product will meet the specific requirements of the first person or entity that purchases the
Product for personal or business use. Knoll‟s liability for the breach of the foregoing limited warranty is limited to
the repair or replacement of the Product or refund of the purchase price of the Product, at Knoll‟ sole option.
Replacement Product may be re-furbished in “like-new” condition, at Knoll‟ sole discretion. To exercise the
Purchaser‟s rights under the foregoing warranty, the Product must be returned at the Purchaser‟s sole cost and
expense, to Knoll or to any authorized Knoll service center provided, and the Product must be accompanied by a
written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer‟s name; and (iii)
the model and serial number of the Product. When sending your unit in for repair, please ship your unit in its
original packing material or a Knoll approved ATA Shipping Case, or have a professional packaging company pack
the unit. Please insure your shipment for its full value. A return authorization number, issued by the Knoll customer
service department, must also be clearly displayed on the outside of the shipping carton containing the Product.
Note: Remanufactured Products are exempt from the foregoing Limited Warranty. Please refer to the
Remanufactured Product Warranty for applicable warranty information.
WARRANTY LIMITATION AND EXCLUSION
Knoll shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering,
alterations, or service other than by Knoll or its authorized agents, causes other than from ordinary use or failure to
properly use the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING
WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT
SIGNED BY KNOLL. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT KNOLL‟ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER
ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT
OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL KNOLL BE
LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST
REVENUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN
LIMITING KNOLL‟ LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO
PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE
CAUSE OF ACTION HAS ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHT WHICH VARIES FROM STATE-TO-STATE.
Copyright 2010 Knoll Systems. All Rights Reserved.
Knoll HDP6000 Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|