1080p DLP
Front Projector
User's Manual
1080p DLP Front Projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Notices
WARNING! To meet FCC requirements, a shielded power cord is required in order to prevent
interference. It is essential that only the supplied power cord is to be used. Use only shielded
cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not approved by the party responsible for compliance could void your authority
to operate the equipment.
WARNING! The projector cooling fan continues to run for approximately 90 seconds after the
projector is turned off using the Power button on the control panel or remote control. Never
unplug the power cable to power off the projector; damage to the lamp may result.
WARNING! High brightness light source. Do not stare into the beam of light, or view directly.
Be especially careful and ensure that children do not stare directly into the beam
of light.
WARNING! To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
CAUTION! For minimal servicing and to maintain high image quality, we recommend that you
use the projector in an environment that is smoke and dust free. When used in areas where
there is a lot of smoke or dust, the filter and lens should be cleaned often to lengthen the
service life of the projector.
WARNING! Some IC chips in this product include confidential and/or trade secret property
belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate,
distribute, reverse engineer, reverse assemble or decompile the contents thereof.
WARNING! The ventilation slots, lamp, and objects next to them may get extremely hot
during operation. Do not touch these areas until they have sufficiently cooled down.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT DISPOSAL
This projector utilizes a tin-lead solder, P-VIP Lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations.
IMPORTANT RECYCLING INSTRUCTIONS
Lamp(s) inside this product contain mercury. This product may contain other elec-
Hg
tronic waste that can be hazardous if not disposed of properly. Recycle or dispose in
accordance with local, state, or federal Laws. For more information, contact the Elec-
Caution regarding the exhaust of the projector.
Do not place the projector in space that is poorly ventilated or confined. Allow at leat 50 cm clearance
from walls and free air flow around the projector.
Exhaust Vent
Wall
or
Block
Before using the projector, please read this operation manual carefully.
To facilitate reporting the loss or theft of your Projector, record the Serial Number located on the
bottom of the projector and retain this information. Before recycling the packaging, be sure that you
have checked the contents of the carton thoroughly against the list of “Package Contents” on page 7.
WARRANTY
Promptly register the Projector’s Warranty using the REGISTRATION CARD packed with the
projector. The Warranty assures that you immediately receive the full benefit of the parts, service and
labor warranty applicable to your purchase.
SYMBOL EXPLANATIONS
DISPOSAL:
Do not use household or municipal waste collection services for disposal of electri-
cal and electronic equipment. EU countries require the use of separate recycling
collection services.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
(Short throw lens) ............................................... 22
(Long throw lens) ................................................ 23
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
Open the package and ensure that you have the following items:
INPUT
INPUT
INPUT
INPUT
1
2
3
4
Remote control
Two “AAA” size
batteries
Power cord
(By country)
WX
GA/720p
DLP FR
ONT PR
OJECT
O
Qu
ick
G
uid
e
R
This
m
anua
l
may
not
b
e
cop
©
Al
l
rig
any
m
edia
i
e
d
i
n
hts
rese
rved
witho
o
r
form
.
u
t
t
h
e
writte
n
con
sent
o
f
the
manu
factur
er
.
RS232 cable
Quick Guide
CD with User’s Manual
HDMI to HDMI cable (3M)
Composite cable
(3.6M)
Optional accessories
VGA to VGA cable
Ceiling mount package
Component cable
S-Video cable
• Some of the cables may not be available depending on the region. Please check with
your nearest Authorized Dealer.
Note
If anything is missing or appears damaged, contact your dealer immediately.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
• Newly developed 0.65-inch 1080p DMD™ chip provides significantly improved optical effi-
ciency and excellent contrast ratio.
• Newly developed LVDS (Low voltage differential signal) chip eliminates Color Breaking phe-
nomena common with previous generation DLP™ projectors.
• Use of high-output lamp realizes both high color purity and high brightness. Natural images
made possible by high color reproducibility can be created with high-brightness, powerful
expression capabilities.
• New i/p conversion algorithm enhances the performance of the motion detect i/p conversion.
• Extensive improvements on the jagged edges or slanted lines in moving images.
• New Edge Up-Scaling.
• As a result of reducing jagged edges and flickering when up-scaling edges of slanted lines,
even signals not reaching a panel resolution of 480i/p can be projected by converting them to
1920X1080 resolution images.
• New Film Mode Function.
• 3:2 pull down enhancement for 480i and 2:2 for 576i signals, but HDTV 1080i signals as well.
• Use of a HDMI/HDCP terminal enables all processes from input to signal processing and pro-
jection to be performed digitally, resulting in the realization of all-digital projection without any
data loss due to analog conversion. This also supports the building of home theaters using
HTPC.
• Provides the new Brilliant Color™ algorithm which provides enhancement to the functions of
degamma, and Spoke light recapture.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Components
Projector (Front and Top View)
Focus ring
Adjust focus.
Zoom ring
Adjust screen display
Focus
Zoom
Lens shift dial
(Vertical)
Lens shift dial
(Horizontal)
ENTER button
(V)
LENS SHIFT
(H)
LENS SHIFT
For setting the selected items
or adjustments from the menu.
Adjustment buttons
(T,S,W,X)
ENTER
For selecting menu items.
STATUS
Exit button
EXIT
For exiting the OSD.
ECO
INPUT
Temperature indicator
This indicator glows red, when
the temperature of the
projector exceeds the set
critical temperature or when
the fan functions abnormally.
ECO button
For power saving/extended
lamp life.
Power (ON/OFF) buttons
For turning the power on or
off.
MENU button
Press this button to enter
the OSD menus.
Power indicator
Blue: The power is ready.
INPUT button
Press this button to select
the input source.
Blue blinking: The fan is
cooling.
Exhaust vent
Intake vent
Remote control sensor
Adjustment foot
Temperature indicator
The projector has an over temperature warning LED on the control panel. If the projector overheats because
of a dirty filter or another problem, the LED will light up, and the projector lamp will turn off, after which a 90-
second cooling off period occurs. After restarting the projector, if the unit doesn’t operate normally, take the
projector in for servicing.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector (Rear View)
Input 3:
Video/S-Video
Terminals for connecting
Video/S-Video.
RS-232C terminal
Command control.
Input 2: HDMI
Terminals for connecting
HDMI.
USB
B type terminal for
service port.
Input 4: PC
Terminal for connecting
Remote control sensor
PC RGB signals.
12V Trigger
Terminals for screen
controlling.
Input 1: Component
Terminals for YPbPr/
YCbCr.
IR Repeater
Terminal for wired
remote control.
AC socket
Input: 100~240VAC
3.5A,50/60Hz.
Exhaust vent
Exhaust vent
Kensington Security
Standard connector
WARNING! As the projector lamp becomes extremely hot, air blowing out from the ventilation
slots can be uncomfortably hot.
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver
Security System. Refer to the information that came with the system for instructions on how to use it to
secure the projector.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
Power (ON/OFF) button
For turning the power on and off.
MENU button
Press this button to
enter the OSD menus.
Adjustment buttons
(T,S,W,X)
For displaying adjustment
ENTER button
For setting the selected
items or adjustments from
the menu.
and setting screens.
EXIT button
For Exiting the OSD.
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 1 button
Selects the source Component
RCA / SCART.
INPUT 2 button
Selects the source HDMI 1 or 2.
INPUT 3 button
Selects the source Video or S-Video.
INPUT 4 button
Selects the source PC.
Aspect Ratio button
Controls how the projector resizes
the input image.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Available Range of the Remote Control
„ The remote control can be used to control the
projector within the ranges shown in the
illustration.
23'(7 m)
45°
30°
Note
30°
• The signal from the remote control can be
reflected by the screen.
When using the remote control:
• Be sure not to drop it, or expose it to moisture
or high temperature.
45°
• The remote control may malfunction under a
23'(7 m)
fluorescent lamp. If that occurs, move the
30°
projector away from the fluorescent lamp.
Inserting the Batteries
The batteries (two “AAA” size) are included in the package.
Press down the tab on the cover
and pull the cover towards the
direction of the arrow.
1
Insert the included batteries.
2
Insert the batteries making sure the
polarities correctly match the
and
marks inside the battery compartment.
Insert the lower tab of the cover
into the opening, and press down
the cover until it clicks in place.
3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Devices
Before Setting Up
Note
• Before connecting, be sure to turn off both the projector and the devices to be connected. After making
all connections, turn on the projector and then the other devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connections
are made.
• Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to
Video equipment:
„ A VCR, Laser disc player or other video equipment.
„ A DVD player or DTV* decoder.
*DTV is the umbrella term used to describe the new digital television system in the United States.
A computer using:
„ HD 15-pin VGA to VGA cable (optional item, sold separately).
Connecting the Power Cord
Plug in the supplied power cord into the
Supplied
accessory
Power cord
AC socket on the rear of the projector.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Video Equipment
Connecting to Video
VCR or other video equipment
Equipment
To S-Video output terminal
To Video output terminal
Using an S-Video or a Composite Video
Cable
Using an S-Video or a Composite video cable,
a VCR, laser disc player or other video
equipment can be connected to INPUT 3 input
terminals.
Note
Composite video cable
• The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture is
separated into color and luminance signals
to realize a higher-quality image. To view a
higher-quality image, use a commercially
available S-Video cable to connect the
INPUT 3 terminal on the projector and the
S-Video output terminal on the video
equipment.
S-Video cable
(commercially available)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To analog component
output terminal
Connecting to Component
Video Equipment
Using a Component Cable (INPUT 1)
Use a component cable when connecting to
the INPUT 1 terminal and component video
equipment such as DVD players and DTV*
decoders.
DVD player or
DTV* decoder
*DTV is an umbrella term used to describe the
new digital television system in the United
States.
Component cable
(commercially available)
Note
• When connecting the projector to the video
equipment in this way, select “Component”
for “Input Source” in the “Main” menu.
The component jack for a DVD and so forth may be
indicated with Y, CB or CR. Connect each jack as shown
below.
Projector
Y
PB
PR
DVD player or
DTV decoder
Y
CB
CR
Connecting by Using a
HDMI to HDMI Cable
Supplied
accessory
HDMI to HDMI
cable
Use an HDMI to HDMI cable when connecting
HDMI video equipment such as DVD players
to INPUT 2 terminal.
To HDMI output terminal
Connect an HDMI to HDMI cable
to the projector.
1
Connect the above cable to the
video equipment.
2
Note
HDMI to HDMI cable
• Select the input signal type of the video
equipment.
DVD player or
DTV* decoder
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to a Computer
Connecting to a Computer
Connect the projector to the computer
Optional
accessory
HD 15-pin
VGA to VGA
cable
using the HD 15-pin VGA to VGA cable.
• Secure the connectors by tightening the
thumbscrews.
Notebook Computer
HD 15-pin VGA to VGA cable
(sold separately)
Note
To VGA output terminal
Chart” for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed
may cause some of the functions not to
work.
• A Macintosh adaptor may be required for
use with some Macintosh computers.
Contact your nearest Authorized Service
Center or Dealer.
• Depending on the computer you are using,
an image may not be projected unless the
signal output setting of the computer is
switched to the external output. Refer to the
computer operation manual for switching
the computer signal output settings.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Thumbscrew Cables
„ Connect the thumbscrew cable making sure that it fits correctly
into the terminal. Then, firmly secure the connectors by tightening
the screws on both sides of the plug.
„ Do not remove the ferrite core attached to the HD 15-pin VGA
cable.
Ferrite core
“Plug and Play” Function
„ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
„ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected
computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Adjustment Feet
The height of the projector can be adjusted
using the adjustment feet when the surface
the projector is placed on is uneven or when
the screen is slanted.
The projection of the image can be made
higher by adjusting the projector when it is in a
location lower than the screen.
Press the foot releases and lift
the projector to the desired
angle.
1
Foot releases
Remove your hands from the foot
2
releases. Once the adjustment
feet have locked in position,
place the projector down.
• If the screen is at an angle, the
adjustment feet can be used to adjust
the angle of the image.
Note
• The projector is adjustable up to
approximately 11 degrees from the standard
position.
Adjustment feet
• When the height of the projector is adjusted,
the image may become distorted
(keystoned), depending on the relative
positions of the projector and the screen.
See page 42 for details on keystone
correction.
Info
• When lowering the projector, be careful not
to get your finger caught in the area
between the adjustment foot and the
projector.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom ring
on the projector.
Focus
Focus ring
Zoom
Zoom ring
Zoom is adjusted by rotating the
zoom ring.
Zoom ring
1
Zoom out
Zoom in
Focus is adjusted by moving the
focus ring.
Focus ring
2
Using the Lens Shift
The height and width of the projected image
can be adjusted to be within the shift range of
the lens by rotating the lens shift dial at the top
of the projector.
Lens shift dial
(Vertical)
Lens shift dial
(Horizontal)
Note
• Do not forcibly turn the lens shift dial beyond
the range of the upper left and lower right
positions. This may cause the projector to
malfunction.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
• The projector lens should be centered in the middle of the screen. If the horizontal line passing through
the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the
lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
„ Place the projector at the required distance from the screen
An Example of Standard Setup
• The distance from the screen to the projector may
vary depending on the size of the screen.
Side View
• The default setting can be used, when placing the
90
projector in front of the screen. If the projected
image is reversed or inverted, readjust the setting to
“Front” for “PRJ Mode” in the “Options” menu.
Audience
Top View
• Place the projector so that an imaginary horizontal
line that passes through the center of the lens is
90
perpendicular to the screen.
H
Note
2D Lens Shift Ability:
• Short throw lens shift:
1/2 of screen height: Up 100%, Down 60%
1/2 of screen height: Left 15%, Right 15%
• Long throw lens shift:
V
1/2 of screen height: Up 140%, Down 60%
1/2 of screen height: Left 15%, Right 15%
1
2
V
• It is recommended that images be projected onto the
dashed line octagonal area for fine image quality.
• There is a tolerance of 5% in the formula above.
1
2
H
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
(Short throw lens)
When using a wide
screen (16:9)
In case of displaying the
16:9 picture on the whole
area of the 16:9 screen.
Wide Screen 16:9
Throw Distance
Max Min
Center of lens to edge of
screen bottom
Screen Size
Diagonal
Wide
cm
High
cm
Up
down
in
cm
in
in
ft
m
11.0
9.2
7.3
5.5
4.9
3.9
3.7
3.4
3.1
2.6
2.2
1.8
ft
m
ft
cm
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ft
cm
300.0
250.0
200.0
150.0
133.0
106.0
100.0
92.0
762.0 261.5 664.1 147.1 373.6
635.0 217.9 553.5 122.6 311.3
36.2
30.1
24.1
18.1
16.0
12.8
12.1
11.1
10.1
8.7
29.0
24.1
19.3
14.5
12.8
10.2
9.7
8.8
7.4
5.9
4.4
3.9
3.1
2.9
2.7
2.5
2.1
1.8
1.5
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
-9.8
-8.2
-6.5
-4.9
-4.3
-3.5
-3.3
-3.0
-2.7
-2.4
-2.0
-1.6
-298.9
-249.1
-199.2
-149.4
-132.5
-105.6
-99.6
508.0 174.3 442.8
381.0 130.7 332.1
337.8 115.9 294.4
98.1 249.1
73.5 186.8
65.2 165.6
52.0 132.0
49.0 124.5
45.1 114.6
41.2 104.6
16
269.2
254.0
233.7
213.4
182.9
152.4
127.0
92.4
87.2
80.2
73.2
62.8
52.3
43.6
234.7
221.4
203.7
186.0
159.4
132.8
110.7
9
8.9
-91.7
84.0
8.1
-83.7
: Picture area
72.0
35.3
29.4
24.5
89.7
74.7
62.3
7.0
-71.7
60.0
7.2
5.8
-59.8
50.0
6.0
4.8
-49.8
The formula for screen size and projection distance
Y1 (Max.) = 0.12057x
Y2 (Min.) = 0.09660x
Z1 (Upper) = 0.00000x
z2 (Lower) = -0.03268x
x : Screen size (diag.)
y : Projection distance
z : Distance from the lens center to the
lower edge of the image
Note
• There is a tolerance of ±3% in the formula above.
• Values with a minus (-) sign indicate the distance of the lens center below the
bottom of the image.
When using a normal
screen (4:3)
In case of setting the
16:9 picture to the full
horizontal width of the 4:3
screen.
Standard Screen 4:3
Center of lens to edge of
Screen Size
Wide
Throw Distance
screen bottom
Up down
cm
Diagonal
High
cm
Max Min
in
cm
in
cm
in
ft
m
10.1
8.4
6.7
5.1
4.5
3.6
3.4
3.1
2.8
2.4
2.0
1.7
ft
m
ft
cm
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
ft
300.0
250.0
200.0
150.0
133.0
106.0
100.0
92.0
762.0 240.0 609.6 180.0 457.2
635.0 200.0 508.0 150.0 381.0
508.0 160.0 406.4 120.0 304.8
33.2
27.7
22.1
16.6
14.7
11.7
11.1
10.2
9.3
26.6
22.2
17.7
13.3
11.8
9.4
8.1
6.8
5.4
4.1
3.6
2.9
2.7
2.5
2.3
1.9
1.6
1.4
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
-12.0 -365.8
-10.0 -304.8
-8.0
-6.0
-5.3
-4.2
-4.0
-3.7
-3.4
-2.9
-2.4
-2.0
-243.8
-182.9
-162.2
-129.2
-121.9
-112.2
-102.4
-87.8
381.0 120.0 304.8
337.8 106.4 270.3
90.0 228.6
79.8 202.7
63.6 161.5
60.0 152.4
55.2 140.2
50.4 128.0
43.2 109.7
4
269.2
254.0
233.7
213.4
182.9
152.4
127.0
84.8
80.0
73.6
67.2
57.6
48.0
40.0
215.4
203.2
186.9
170.7
146.3
121.9
101.6
8.9
8.2
3
84.0
7.4
72.0
8.0
6.4
60.0
36.0
30.0
91.4
76.2
6.6
5.3
-73.2
50.0
5.5
4.4
-61.0
: Screen area
: Picture area
The formula for screen size and projection distance
Y1 (Max.) = 0.11067x
Y2 (Min.) = 0.08867x
Z1 (Upper) = 0.00000x
Z2 (Lower) = -0.03268x
x : Screen size (in)
y : Projection distance (ft)
z : Distance from the lens center to the
lower edge of the image(in)
Note
• There is a tolerance of ±3% in the formula above.
• Values with a minus (-) sign indicate the distance of the lens center below the
bottom of the image.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Size and Projection Distance
(Long throw lens)
When using a wide
screen (16:9)
In case of displaying the
16:9 picture on the whole
area of the 16:9 screen.
Wide Screen 16:9
Throw Distance
Max Min
Center of lens to edge of
screen bottom
Screen Size
Diagonal
WIde
cm
High
cm
Up
down
in
cm
in
in
ft
m
13.9
11.6
9.3
6.9
6.2
4.9
4.6
4.3
3.9
3.3
2.8
1.9
ft
m
11.0
9.2
7.3
5.5
4.9
3.9
3.7
3.4
3.1
2.6
2.2
1.5
ft
cm
ft
cm
300.0
250.0
200.0
150.0
133.0
106.0
100.0
92.0
762.0 261.5 664.1 147.1 373.6
635.0 217.9 553.5 122.6 311.3
45.5
37.9
30.4
22.8
20.2
16.1
15.2
14.0
12.8
10.9
9.1
36.2
30.1
24.1
18.1
16.0
12.8
12.1
11.1
10.1
8.7
2.5
2.0
1.6
1.2
1.1
0.9
0.8
0.8
0.7
0.6
0.5
0.3
74.7
62.3
49.8
37.4
33.1
26.4
24.9
22.9
20.9
17.9
14.9
10.0
-9.8
-8.2
-6.5
-4.9
-4.3
-3.5
-3.3
-3.0
-2.7
-2.4
-2.0
-1.3
-298.9
-249.1
-199.2
-149.4
-132.5
-105.6
-99.6
508.0 174.3 442.8
381.0 130.7 332.1
337.8 115.9 294.4
98.1 249.1
73.5 186.8
65.2 165.6
52.0 132.0
49.0 124.5
45.1 114.6
41.2 104.6
16
269.2
254.0
233.7
213.4
182.9
152.4
101.6
92.4
87.2
80.2
73.2
62.8
52.3
34.9
234.7
221.4
203.7
186.0
159.4
132.8
88.6
9
-91.7
84.0
-83.7
: Picture area
72.0
35.3
29.4
19.6
89.7
74.7
49.8
-71.7
60.0
7.2
-59.8
40.0
6.1
4.8
-39.8
The formula for screen size and projection distance
Y1 (Max.) = 0.15180x
Y2 (Min.) = 0.12057x
Z1 (Upper) = 0.00817x
Z2 (Lower) = -0.03268x
x : Screen size (in)
y : Projection distance (ft)
z : Distance from the lens center to the
lower edge of the image (in)
Note
• There is a tolerance of ±3% in the formula above.
• Values with a minus (-) sign indicate the distance of the lens center below the
bottom of the image.
When using a normal
screen (4:3)
In case of setting the
16:9 picture to the full
horizontal width of the 4:3
screen.
Standard Screen 4:3
Center of lens to edge of
Screen Size
WIde
Throw Distance
Max Min
screen bottom
Up down
cm
Diagonal
High
cm
in
cm
in
cm
in
ft
m
12.7
10.6
8.5
6.4
5.6
4.5
4.2
3.9
3.6
3.1
2.5
1.7
ft
m
10.1
8.4
6.7
5.1
4.5
3.6
3.4
3.1
2.8
2.4
2.0
1.3
ft
cm
ft
300.0
250.0
200.0
150.0
133.0
106.0
100.0
92.0
762.0 240.0 609.6 180.0 457.2
635.0 200.0 508.0 150.0 381.0
508.0 160.0 406.4 120.0 304.8
41.8
34.8
27.9
20.9
18.5
14.8
13.9
12.8
11.7
10.0
8.4
33.2
27.7
22.1
16.6
14.7
11.7
11.1
10.2
9.3
3.0
2.5
2.0
1.5
1.3
1.1
1.0
0.9
0.8
0.7
0.6
0.4
91.4 -12.0 -365.8
76.2 -10.0 -304.8
61.0
45.7
40.5
32.3
30.5
28.0
25.6
21.9
18.3
12.2
-8.0
-6.0
-5.3
-4.2
-4.0
-3.7
-3.4
-2.9
-2.4
-1.6
-243.8
-182.9
-162.2
-129.2
-121.9
-112.2
-102.4
-87.8
381.0 120.0 304.8
337.8 106.4 270.3
90.0 228.6
79.8 202.7
63.6 161.5
60.0 152.4
55.2 140.2
50.4 128.0
43.2 109.7
4
269.2
254.0
233.7
213.4
182.9
152.4
101.6
84.8
80.0
73.6
67.2
57.6
48.0
32.0
215.4
203.2
186.9
170.7
146.3
121.9
81.3
3
84.0
72.0
8.0
60.0
36.0
24.0
91.4
61.0
6.6
-73.2
40.0
5.6
4.4
-48.8
: Screen area
: Picture area
The formula for screen size and projection distance
Y1 (Max.) = 0.13933x
Y2 (Min.) = 0.11067x
Z1 (Upper) = 0.00817x
Z2 (Lower) = -0.03268x
x : Screen size (in)
y : Projection distance (ft)
z : Distance from the lens center to the
lower edge of the image (in)
Note
• There is a tolerance of ±3% in the formula above.
• Values with a minus (-) sign indicate the distance of the lens center below the
bottom of the image.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection from behind the screen
Projecting a Reversed/Inverted Image
„ Place a translucent screen between the projector and the
audience.
When using the default setting.
TOn-screen Display
„ Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu.
The image is reversed.
Projection using a mirror
„ Place a mirror (normal flat type) in front of the lens.
„ Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu, when the mirror is placed on the side
where the audience is.
When using the default setting.
TOn-screen Display
The image is reversed.
Info
• When using a mirror, be sure to carefully position
both the projector and the mirror so that the light
does not shine into the eyes of the audience.
Ceiling-mount setup
„ It is recommended that you use the optional ceiling-
mount bracket for this installation.
When using the default setting.
TOn-screen Display
„ Before mounting the projector, contact your nearest
Authorized Service Center or Dealer to obtain the
recommended ceiling-mount bracket (sold separately).
„ Be sure to adjust the position of the projector to match
the distance (Z) from the lens center position to the
lower edge of the image, when mounting the projector
on the ceiling.
„ Invert the image by setting “Ceiling + Front” for “PRJ
Mode” in the “Options” menu.
The image is reversed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
• The language preset at the factory is
English. If you want to change the on-
screen display to another language, reset
the language according to the procedure on
Plug the power cord into the wall
outlet.
T, S, W, X buttons
1
Temperature Indicator
ECO button
EXIT button
ENTER button
INPUT button
MENU button
• The power indicator illuminates blue,
and the projector enters standby
mode.
Power
button
Press
or
on the remote control
on the projector.
2
ENTER
• The power indicator turns off.
STATUS
EXIT
MENU
Note
ECO
INPUT
Power
indicator
(Blue)
• The power indicator illuminates,
indicating the status of the lamp.
Blue: The power is ready.
Blue blinking: The fan is cooling.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Press
on the projector to
3
INPUT
Power button
select the INPUT mode.
MENU button
T, S, W, X
buttons
EXIT button
INPUT 2 button
INPUT 4 button
Note
INPUT
INPUT
INPUT
INPUT
1
2
3
4
INPUT 1 button
INPUT 3 button
• When a signal is not received,
“Searching for Source” will be
displayed.
About the INPUT modes
Selects the source Com-
ponent RCA / SCART.
INPUT 1
INPUT 2
Selects the source HDMI
1 or 2.
INPUT button
INPUT
Selects the source Video
or S-Video.
INPUT 3
INPUT 4
Selects the source PC.
ENTER
STATUS
EXIT
MENU
ECO
INPUT
Note
• If you select “Auto” as the input
source, then the correct input source
is selected automatically.
Press
or
on the remote control
4
on the projector, then press
Enter to turn off the projector,
when the confirmation message
is displayed.
Note
• If you accidentally press power
and do not want to turn off the
projector, press Exit button or select
Cancel to turn off the confirmation
message.
Info
• Do not unplug the power cord during
projection or cooling fan operation.
This can cause damage due to the
rise in internal temperature, as the
cooling fan also stops.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the On-screen
Display Language
• The on-screen display language of the
projector can be set to English, Francis,
Italiano, Deutsch, Spanish, 中文 , 日本語 ,
한국어 .
Press “MENU”.
1
• The menu will be displayed.
Press
“Language”.
or X to select
2
3
Press S or T to select desired
language, and then press
.
The desired language will be set as the
on-screen display.
Press “EXIT”.
4
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Bar Items
This list shows the items that can be set in the projector.
Picture
Brightness -50 ~ +50
Options
ECO Mode
ON/OFF
0~31
Contrast
Color
Tint
-50 ~ +50
-64 ~ +64
-64 ~ +64
Sync Threshold
(Component only)
Auto Power OFF
Source Select
ON/OFF
Manual/Auto
Softest, Softer, Normal,
Sharper, Sharpest
Sharpness
5. 15. 60 secs,
Limitless
OSD Time Out
1.0/1.5/1.8/2.0/2.2/2.35/2.5/
2.8
Gamma
OSD Blending
Film Mode
ON/OFF
Color Temp
Color Space
Warm, D65, Native, Cool, Cold
Auto/Video/Film
Auto, RGB, RGB Video,
REC 709, REC 601
STI
LTI Level
CTI Level
R Gain/G Gain/B Gain/
R Offset/G Offset/B Offset/
Reset
White Balance
Black Level
(S-Video and Composite Video
only)
Noise Reduction
(SDTV/EDTV
only)
TNR
0 IRE/7.5 IRE
MNR
Normal/Bright/Movie/
Memory 1/Memory 2/
Memory 3
Picture Setting
BAR
Save Picture Settings
Blank Screen
Reset
Black/Blue
Dynamic Black
Advance
Reset
Brilliant Color
Front/Front Ceiling/
Rear/Rear Ceiling
PRJ Mode
Detail Enhancement
Lamp Timer Reset
Status
Fine Sync
Clock
-10 ~ +10
-16 ~ +15
(Component
and VGA
only)
Phase
Input Source
PC
Execute Auto Tune
Auto Tune
HDMI 1
ON/OFF
HDMI 2
Reset
Component
Composite
Layout
Overscan Type
Zoom/Crop
0~10
Overscan Adjust
Aspect Ratio
S-Video
Anamorphic/Standard/
LetterBox/Virtual Wide
SCART
Horizontal Position
Vertical Position
SCART Enable
Enable/Disable
English
Francis
Italiano
Deutsch
Spanish
中文
Language
Horizontal Keystone
(1080i Hide)
Vertical Keystone (1080i Hide)
Reset
日本語
한국어 .
Factory Reset
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
This projector has one set of menu
screens that allow you to adjust the
image and various projector settings.
You can operate the menus from the
projector or remote control using the
following procedure.
ENTER
STATUS
EXIT
MENU
Menu Selections
(Adjustments)
ECO
INPUT
1
MENU button
Press
on remote or
on
MENU
MENU
keypad.
• The menu screen is displayed.
Note
MENU button
• The “Picture” menu screen for the
selected input mode is displayed.
INPUT
1
2
3
4
INPUT
INPUT
INPUT
Press S or T to select the menu
you want to adjust.
2
3
Press X or
to reach the Sub-
menu and then press S or T to
select the item you want to
adjust.
Note
• The selected item will be highlighted.
Press W or X to adjust the item
selected.
4
• The adjustment is stored.
Press
MENU”.
to return to “Main
5
6
Press , the menu screen will
disappear.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
You can adjust the projector's picture to
your preferences with the following picture
settings.
Adjusting Image Preferences
Selected item
Description
For adjusting the
brightness of an image
Brightness
Contrast
Color
For lower brightness
For higher brightness
For higher contrast
For adjusting the contrast
level
For lower contrast
For adjusting the color
intensity of an image
For lower color intensity
Skin tones become purplish
For higher color intensity
For adjusting the tones of
an image
Skin tones become
greenish
Tint
Brightness
Use this option to adjust the overall brightness of the image. Use this control in conjunction with contrast to
fine-tune the display. The scale is from -50 to 50.
Contrast
Use this option to adjust the contrast of the image. Use this control in conjunction with contrast to fine-tune
the display. The scale is from -50 to 50.
Color
Use this option to adjust the color intensity of the image.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Tint
Use this option to adjust the tint of your image. Press X to make the image more green. Press W to make the
image more purple.
Sharpness
Use this option to adjust the clarity and focus of the image.
Gamma
Use this option to adjust the gamma correction of the image. Default setting is 2.2. Gamma correction
provides eight sets of gamma corrections 1.0, 1.5, 1.8, 2.0, 2.2, 2.35, 2.5, and 2.8.
Color Temp
Use this option to set the color temperature of the image. There are five settings in the Color Temperature.
They are Warm, D65, Native, Cool, and Cold. The Cold color temperature makes the image look colder with
bluish hue, and the Warm color Temperature makes the image look warmer with reddish hue. When sets to
"Native", the image has the maximum brightness.
Color Space
Use this option to determine how the color components of an input signal are decoded for accurate color on
the display. In most situations, the Auto setting produces the most accurate colors. If it does not, try the other
settings and select the one that does.
White Balance
To remove any trace of color from the white areas of the projected image, choose White Balance from the
Picture menu and press ENTER.
Gain: Use the Gain controls to correct color imbalances in the bright areas of the image.
Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalance in the dark areas
of the image.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Level
This control compensates for incoming elevated black levels present in certain video signals. For some types
of video, you may want to override the setting. Set it to 0 IRE if blacks appear elevated (dark gray). If blacks
appear “crushed” (too dark), set it to 7.5 IRE.
Picture Setting
This function stores Brightness, Contrast, Color, Tint, Sharpness, Gamma, Color Temperature, Color Space,
Brilliant Color, and Black Level set in “Picture”. Each stored setting is reassigned to each input and
resolution mode.
Select “Picture Setting” from the “Picture” menu on the menu screen.
Note
• When Recalling Saved Contents:
When a saved memory number is selected,
the contents of the “Picture” menu change
to the adjustment values of the saved
memory number.
• When Editing Saved Contents:
Edit the contents of the “Picture” menu after
selecting the Memory number for which
adjustment values are to be edited.
• The default three modes Normal/Bright/
Movie cannot be saved in the memory.
Save Picture Settings
Use this option to save changes you made in “Picture setting” to Memory 1, Memory 2, or Memory 3.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Advance
Select this menu to access Dynamic Black, Brilliant Color and Detail Enhancement functions.
Dynamic Black: This function utilizes the
contrast of colors to enable black colors to
appear blacker on screen while significantly
enhancing the performance of black scenes.
• To enable the function, set it to “ON”.
Brilliant Color: This function utilizes a new
color-processing algorithm and system level
enhancements to enable higher brightness
while providing truer and more vibrant colors
in picture.
• To enable the function, set it to “ON”.
Detail Enhancement: This function
sharpens the details of the picture.
The following options are available: Off, Low,
Middle, High.
Reset
Select this option to set to all items in the "Picture" menu to the factory default values.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Computer Images
(Component / PC only)
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in
portions of the screen.
Select “Clock”, “Phase”, “Execute
Auto Tune”, and “Auto Tune” in the
“Fine Sync” menu on the menu
screen.
Selected item
Clock
Description
Adjusts vertical noise.
Adjusts horizontal
noise (similar to
tracking on your
VCR).
Phase
Execute Auto Tune
(PC only)
To run auto tune.
Automatically adjusts
a computer image.
Select “Execute Auto
Tune”.
Auto Tune
(PC only)
Note
• Auto Tune may take some time to complete,
depending on the image stored in the
computer connected to the projector.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Picture Display Mode
This function allows you to modify or customize the picture display mode to enhance the
input image. Depending on the input signal, you can choose “Anamorphic”, “Standard”,
“LetterBox”, or “Virtual Wide”.
Switching the Picture Display Using
Different input signals
Press
on remote or
on keypad
MENU
and select layout.
• Each time is pressed, the display
INPUT
INPUT
INPUT
INPUT
1
2
3
4
Aspect Ratio
Aspect Ratio Function
The layout menu enables you to control how
the projector resizes the input image.
The following options are available:
Anamorphic
• Resolution 1920x1080
• 4:3 input is stretched to fit 16:9 display
• Stretches entire image.
Standard
• Resolution depends on the Input Signal
• 4:3 input scaled to fit display height
• Width scaled to maintain 4:3 aspect ratio
• Black bars on left and right (taking up 25% of
the whole display)
LetterBox
• Resolution 1920x1080
• 4:3 input scaled to fit display width
• Height scaled to maintain 4:3 aspect ratio:
1440x1080
• 25% of the entire image on the top and bottom
is cropped.
Virtual Wide
• Resolution 1920x1080
• 4:3 input is stretched to fit 16:9 display
• With 4:3 input, the central ratio remains true to
scale, but the image is stretched to fit display
width.
• 16:9 input image is identical to the one
displayed in Anamorphic mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO
Anamorphic
1920x1080
Standard
LetterBox
Virtual Wide
1920x1080
480i
480p
576i
576p
NTSC
PAL
For 4:3
aspect ratio
1440x1080
1920x1080
SECAM
480p
576p
1920x1080
1440x1080
1920x1080
1920x1080
For 16:9
aspect ratio
720p
1920x1080
1920x1080
1440x1080
1440x1080
1920x1080
1920x1080
1920x1080
1920x1080
1080i/p
Output screen image
Input Signal
Anamorphic
Standard
LetterBox
Virtual Wide
For 4:3 aspect ratio
LetterBox image
480i 480p 576i 576p
NTSC PAL SECAM
1080i/p
720p
For 16:9 aspect
ratio
38
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER
Anamorphic
1920X1080
1920X1080
1920X1080
1920X1080
1920X1080
Standard
LetterBox
N.A.
Virtual Wide
1920X1080
1920X1080
1920X1080
1920X1080
1920X1080
VGA(640X480)
SVGA(800X600)
XGA(1024X768)
1440X1080
1440X1080
1440X1080
1440X1080
1440X1080
N.A.
For 4:3
aspect ratio
N.A.
SXGA(1280X1024)
UXGA(1600X1200)
N.A.
N.A.
.
Output screen image
Input Signal
Standard
Anamorphic
Letter Box
Virtual Wide
VGA
SVGA
XGA
N.A.
For 4:3 aspect ratio
(640x480)
N.A.
N.A.
N.A.
For 4:3 aspect ratio
(800x600)
For 4:3 aspect ratio
(1024x768)
SXGA
For 5:4 aspect ratio
(1280x1024)
UXGA
N.A.
For 4:3 aspect ratio
(1600x1200)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Overscan Type
This function enables you to remove
some edges of the image.
Select “Overscan Type” from the
“Layout” menu on the menu screen.
The following options are available:
Selected item
Zoom
Description
Scales or zooms the
image.
Cuts a portion of the
image.
Crop
Overscan Adjust
This function enables you to adjust
the image display on screen. Available
options are from 0-10. The default
value is 1 which is suitable for S-
Video/Composite and Component
input sources.
Select “Overscan Type” from the
“Layout” menu on the menu screen.
• Press “W” or “X” to select value.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
H-V Position Function
This function enables you to center
the display vertically and horizontally.
Press “W” or “X” of the
Horizontal Position, the display
will move to the left or the right.
1
Press “W” or “X” of the Vertical
Position, the display will move
upward or downward.
2
41
Download from Www.Somanuals.com. All Manuals Search And Download.
H-V Keystone Function
Correcting Trapezoidal Distortion and
Adjusting Vertical Size of the picture.
This function allows for Keystone correction.
Note
• When the image is projected either from top
or from bottom toward the screen at an
angle, the image becomes distorted
trapezoidally.
The function for correcting trapezoidal
distortion is called Keystone Correction.
• The Keystone Correction can be adjusted.
(On-screen Trapezoidal Distortion)
Correction and the adjustment of the vertical
size of the picture.
Select “Vertical Keystone” or
“Hertical Keystone” in the layout.
1
* “V-SIZE” is not
displayed when the
value of “KEYSTONE”
is “0”.
Compresses
upper side.
Selected item
Description
Horizontal
Keystone
Horizontally adjusts the
keystone settings.
Vertical
Keystone
Vertically adjusts the
keystone settings.
Compresses
lower side.
Press“W” or “X” to adjust the
keystone correction.
2
Horizontal Keystone Correction
Note
• Since the trapezoidal distortion of the image
can be corrected up to various angles, the
actual screen can be diagonally set up to
that angle as well.
• Straight lines or the edges of images may
appear jagged while adjusting the image.
Vertical Keystone Correction
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Economy Mode
These functions allow you to reduce the power consumption of the projector.
Setting the Power Save
Select “ON” from the “Economy
Mode” under the “Options” menu on
the menu screen.
ENTER
STATUS
EXIT
MENU
ECO
INPUT
Note
• Although noise is reduced when “ECO” is
set to “ON”, brightness decreases by 20%.
ECO Mode
• “ECO” mode is factory preset to “ON”.
Power
consumption
Status
Brightness
80%
ON
(Low power
mode)
325W@110V
OFF
(Standard
mode)
100%
365W@110V
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Sync Threshold
This function is only available on Component
input.
The projector is compatible with EDTV(480p
and 576p) and HDTV(720p,1080i and 1080p)
video signals. If a hardware device, such a
DVD player, is not syncing properly with the
projector, adjust this option to help it to sync
when connected to the projector.
Select “Sync Threshold” from the
“Options” menu on the menu screen.
Automatic Power OFF Function
When an input signal is not detected or you
don't press any input button on Keypad or
remote for more than 15 minutes, the
projector will automatically turn off if set to
“ON”.
Auto Power OFF function will be disabled
when it is set to “OFF”.
Select “Auto Power OFF” from the
“Options” menu on the menu screen.
Note
• When the Auto Power OFF function is set to
“ON”, 5 minutes before the power turns off,
the message “Power OFF in 5 min.” will
appear on the screen to indicate the
remaining minutes.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Source Select
Used to select the input source automatically
when there is no signal in the current input.
Auto
Source Select
Manual
ꢀSelect “source select” from the
“Options” menu on the menu
screen. For operating the menu
OSD Time Out
OSD Time Out is used to set how long the
OSD will stay open if no buttons are pressed.
5
15
60
OSD Time Out
Limitless
45
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Blending
When this function is enabled, the OSD is
transparently displayed on the screen to blend
with the image.
Select “ON” from the “OSD Blending”
under the “Options” menu on the
menu screen.
Film Mode
This function allows you to determine the type of incoming video content-film. Different algorithms are applied
for each of the content types.
Select “Film Mode” from the
“Options” menu on the menu screen.
Reproduces the image of
the film source clearly.
Displays the optimized
image of film transformed
Film Mode
with 3:2 pull down (NTSC
and PAL60Hz)or 2:2 pull
down (PAL 50Hz and
SECAM) enhancement to
progressive mode images.
Note
• In PAL50Hz or SECAM, the 2:2 pull down
enhancement will be enabled only in film
mode, after the film source has been
entered.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
STI
This function allows you to set the LTI and CTI level.
Selected Item
Description
LTI
Adjusts the LTI level to
enhance luminance, filter fuzzy
edges and remove smear.
(Luminance
Transient
Image)
CTI
Adjusts the CTI level to enhace
colour, filter fuzzy edges, and
remove smear.
(Colour
Transient
Image)
Select “STI” from the “Options” menu
on the menu screen.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise Reduction
This function is only available for SDTV (480i/576i) and EDTV (480p/576p) signals.
Noise Reduction is useful for clearing up noisy images. Turn it On to keep in mind that reducing noise (which
reduces high frequencies) may also “soften” the image.
Select “Noise Reduction” from the
“Options” menu on the menu screen.
Blank Screen
This function is used to apply the background color when there is no input source.
Select “Blank Screen” from the
“Options” menu on the menu screen.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset
Select this option to set all items in the
“Options” menu to the factory default values
except PRJ Mode and Lamp Reset.
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or invert the
projected image for various applications.
Setting the PRJ Mode
Select “PRJ Mode” from the “Options”
menu on the menu screen.
Selected item
Front
Description
Normal image
Inverted image
Reversed image
Front + Ceiling
Rear
Reversed and
inverted image
Rear + Ceiling
Note
• This function is used for the reversed image
and ceiling-mount setups.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Timer Reset
Lamp Timer Reset is used to reset the lamp counter. You should reset the Timer after you install a new lamp.
The cumulative lamp usage time is shown in the Status Screen.
Status
The Status screen displays information about the current input signal, Lamp Timer, and Firmware
Information.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Source
In the Main menu, press the S or T button to
select Input Source, and press the Enter button to
confirm.
Note
• If you select “Auto” as the Input source, then
the correct input source is automatically
selected.
Factory Reset
This process will set all the items to Factory
default settings except PRJ Mode and Lamp
Reset.
Note
• If you accidentally press enter and do not
want to perform the factory reset function,
press Exit button or select No to turn off the
confirmation message.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
„ Unplug the power cord before cleaning the projector.
„ Avoid using benzene or thinner, as these can damage the finish on the cabinet and operation panel.
„ Do not use volatile agents such as insecticides on the projector.
„ Do not leave rubber or plastic objects in contact with the projector for long periods as they may damage
the finish of the projector.
„ Wipe off dirt gently with a soft flannel cloth.
„ For hard-to-remove dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then
wipe the projector.
Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test
on a small, inconspicuous area on the projector before using.
Neutral detergent
diluted with water
Cleaning the lens
„ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning
the lens. Do not use any liquid cleaning agents, as they may wear off the coating film on the surface of the
lens.
Cleaning
Paper
„ The surface of the lens is easily damaged, do not to scrape or hit the lens.
Cleaning the exhaust and intake vents
„ Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the Ventilative Holes
• This projector is equipped with ventilative
holes to ensure the optimal operating
condition of the projector.
Side and Rear view
Bottom view
• Periodically clean the ventilative hole by
vacuuming it off with a vacuum cleaner.
• The ventilative holes should be cleaned
every 100 hours of use. Clean the
ventilative holes more often when the
projector is used in a dirty or smoky
location.
Ventilative holes
Ventilative holes
Cleaning the
Ventilative Holes
ENTER
STATUS
EXIT
MENU
Turn off the power and
disconnect the power cord.
ECO
INPUT
1
INPUT
INPUT
1
2
Press
on the projector or
on
the remote control to turn off the power.
Wait until the cooling fan stops.
Power button
Unplug the Power Cord.
2
3
Clean the dust off by placing the
cleaner hose on the intake and
exhaust ventilative holes.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Lamp
The projector lamp has a life of 2000 hours. Maintain proper ventilation to keep the lamp operating
throughout its lifetime. Do not subject the projector to unnecessary vibration to ensure that the
lamp does not break.
„ It is recommended that the lamp (sold separately) be replaced after approximately 2,000 cumulative hours
of use or when you notice a significant deterioration in the picture and color quality. The number of hours
the lamp has been used can be checked with “Lamp Timer” in the “Options” menu on the menu screen.
„ For lamp replacement, please consult your nearest Authorized Service Center or Dealer.
„ The actual lamp service life may be less than 2000 hours depending on the environment in which the
projector is used.
Caution Concerning the Lamp
„ This projector uses a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure is
caused by excessive shock, improper cooling, surface scratches or deterioration of the lamp due to usage.
The period of time up to failure largely varies depending on the individual lamp and/or the condition and
the frequency of use. It is important to note that failure can often result in the bulb cracking.
„ When the lamp replacement indicator and on-screen display icon are illuminated or are flashing, it is
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be
operating normally.
„ If the lamp breaks glass particles may spread inside the lamp cage or gas contained in the lamp may be
vented into the room from the exhaust vent. As the gas in this lamp contains mercury, ventilate the room
well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult
with a doctor as soon as possible.
„ If the lamp breaks, there is also a possibility that glass particles may spread inside the projector.
If this happens, it is recommended you contact your nearest Authorized Dealer to remove the damaged
lamp and assure safe operation.
Replacing the Lamp
CAUTION! Do not remove the lamp unit immediately after operation of the projector. The
lamp will be hot and touching it can lead to burn or injury. Wait at least one hour after the
power cord is disconnected to allow the surface of the lamp unit to fully cool before removing
the lamp unit.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature LED (Over Temperature)
The over temperature alarm LED on the control panel alerts you when the projector lamp becomes too hot or
the peripheral is sultry.
ENTER
Temperature LED
STATUS
EXIT
MENU
ECO
INPUT
If the LED illuminates during operation, the lamp will shut off and the cooling fans will continue to run for
approximately 1.5 minutes. You should ensure that the airflow around the projector is sufficient, and that the
air filters are not clogged to ensure that the projector has proper ventilation.
When the temperature LED lights up, a warning also appears on the screen.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing the Lamp Unit
Follow these instructions to replace the lamp.
• Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or
the inside of the projector.
• To avoid injuring yourself and damage to the lamp, be sure to carefully follow the steps below.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
(Only the silver screws are loosened).
1. If the projector is running, press
on the projector or
on the remote control to
turn off the power. Wait until the cooling fan stops.
ENTER
STATUS
EXIT
MENU
ECO
INPUT
INPUT
INPUT
1
2
Warning!
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn
or injury.
2. Disconnect the power cord and wait at least an hour for the lamp to cool.
3. Remove the lamp unit cover.
• Loosen the user service screw that secures the lamp unit cover. Then open the cover in the direction of the
arrow.
M4* 8.9 screws
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the lamp unit.
• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction
of the arrow.
5. Insert the new lamp unit.
• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
• Attach the lamp unit cover.
• Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then
tighten the user service screw.
Info
• If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord
is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1. Connect the power cord.
• Plug the power cord into the AC socket of the
projector.
2. Reset the lamp timer.
• Select the “Lamp Timer Reset” from the “Options”
menu from the menu screen. Press
. Select “OK”
• “LAMP 0H” is displayed, indicating that the lamp timer
is reset.
Info
Make sure to reset the lamp timer only when replacing
the lamp. If you reset the lamp timer and continue to
use the same lamp, this may cause the lamp to become
damaged or explode.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
RS-232C Port: 9 pin Mini pin plug connector to D-Sub Female connector
8
7
6
Pin No. Signal
Name
I/O
Reference
Not connected
Connected to internal circuit
1
2
3
4
5
6
7
8
9
SD Send Data
RD Receive Data
Input
Output Connected to internal circuit
Not connected
SG Signal Ground
Connected to internal circuit
Not connected
Not connected
Not connected
Not connected
5
9 2 1 4
3
HDMI Port: 19 pin male connector of the High Definition Multimedia Interface
Pin No.Signal
Pin No.Signal
17
3
1
2
3
4
5
6
7
8
9
T.M.D.S data 2+
T.M.D.S data 2 shield
T.M.D.S data 2-
T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1-
T.M.D.S data 0+
T.M.D.S data 0 shield
T.M.D.S data 0-
11 T.M.D.S clock shield
12 T.M.D.S clock-
13 Not connected
14 Reserved (N.C. on device)
15 DDC clock
19
18
1
2
16 DDC data
17 DDC ground
18 +5V power
19 Hot plug detection
10 T.M.D.S clock+
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 25-91 kHz, Vertical Frequency: 24-85 Hz, Pixel Clock: 25-162 MHz
• XGA, SXGA, UXGA compatible with advanced intelligent compression
The following is a list of modes that conform to VESA. However, this projector supports
other signals that are not VESA standards.
PC/
Horizontal
Vertical
VESA DVI-D/HDMI
PC/
Horizontal
Vertical
MAC/
WS
Resolution
Frequency Frequency
VESA DVI-D/HDMI
Standard
Support
MAC/
WS
Resolution
Frequency Frequency
(kHz)
35.1
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
64.0
80.0
91.1
65.2
75.0
(Hz)
56
60
72
75
85
60
70
75
85
60
75
85
60
60
Standard
Support
(kHz)
31.5
31.5
37.9
37.5
43.3
(Hz)
70
DOS 720 x 400
3
60
SVGA 800 x 600
3
3
PC
72
3
3
3
VGA 640 x 480
3
75
85
PC
XGA 1024 x 768
SXGA 1280 x 1024
3
3
3
3
Vertical
Horizontal
VESA
DVI
Resolution
Frequency Frequency
Standard Support
(kHz)
(Hz)
60
50
60
50
60
50
24
50
60
720 × 480
720 × 576
31.5
31.3
45
WSXGA 1680 x 1050
UXGA 1600 x 1200
3
3
3
3
1280 × 720
37.5
33.8
28.1
27
MAC
13”
VGA
640 x 480
34.9
49.6
48.4
67
75
60
HDMI
3
1920 × 1080i
MAC
16”
SVGA 832 x 624
XGA 1024 x 768
MAC
19”
3
1920 x 1080p
56.3
67.5
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data
in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
• When projecting video images of an interlace video signal with the projector, the intended image may
not be projected depending on the video signal when using the RBG input. In such cases, use the
component input, S-Video input or video input.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Compatibility Chart
Component
Support
S-Video
Support
Composite
Support
HDMI
Support
Resolution
H-Freq (kHz) V-Freq (Hz)
SD Video
NTSC
PAL
640x480i
768x576i
768x576i
15.7
15.6
15.6
59.94/60
50
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
SECAM
NTSC-4.43
PAL-M
50
PAL-N
NTSC-J
PAL-60
NTSC-50
480p
60
50
ED TV
HD TV
720x480p
720x576p
31.5
31.3
33.8
28.1
33.8
37.5
45.0
27.0
28.1
33.8
56.3
67.5
36
59.94/60
50
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
576p
1035i/60
1080i/50
1080i/60
720p/50
720p/60
1080p/24
1080p/25
1080p/30
1080p/50
1080p/60
720p/48
1920x1035i
1920x1080i
1920x1080i
1280x720p
1280x720p
1920x1080p
1920x1080p
1920x1080p
1920x1080p
1920x1080p
1280x720p
60
50
59.94/60
50
59.94/60
24
25
30
50
60
HTPC
48
1. Component supports signal formats are Y/Pb/Pr, Y/Cb/Cr.
2. VGA port support signal formats are RGBHV, RGsB, and RGBCs.
DTV
Signal
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
HDMI Support
480i
15.7
31.5
15.6
31.3
45.0
37.5
33.8
28.1
27
60
60
50
50
60
50
60
50
24
25
30
50
60
480p
3
576i
576p
3
3
3
3
3
3
3
3
3
3
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
1080p
28.1
33.8
56.3
67.5
IR Remote Key Discrete Codes
Key
IR POWER
IR MENU
IR UP
Code
Key
Code
0x0d
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0a
0x0b
0x0c
IR_PowerOff
IR_Standard
IR_Letterbox
IR_Anamorphic
0x0e
0x0f
0x10
IR DOWN
IR LEFT
IR RIGHT
IR ENTER
IR_Exit
IR_S_Video
IR_Composite
IR_Component
IR_PC
0x12
0x13
0x14
0x15
0x16
0x17
IR_Source1
IR_Source2
IR_Source3
IR_Source4
IR_ASPECT
IR_HDMI1
IR_HDMI2
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Projector does not start
No picture
Check
Projector power cord is not plugged into the wall outlet.
Remote control batteries have run out.
The selected input mode is wrong.
Cables may be incorrectly connected to the rear panel of the projector.
Power to the external connected device is off.
The video signal format of the video equipment is not set correctly.
Picture adjustments are incorrectly set.
Color is faded
Adjust the focus
The projection distance exceeds the focus range.
Picture is blurred
(Component/VGA input only)
Perform "Fine Sync" adjustments ("Clock" adjustment) also in component
Perform "Fine Sync" adjustments ("Phase adjustment) also in component
Picture noise appears.
Change the input signal type of the video equipment.
Picture is green on
INPUT1 COMPONENT
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture adjustments are incorrectly set.
Picture is dark or
bright and whitish
Picture adjustments are incorrectly set.
Picture is too bright
and whitish
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Specifications
Item Description
Model No. 1080p DLP Front Projector
DLP Panel Panel size: 0.65''
Display method: DMD by Texas Instruments
Device method: Digital Light Processing (DLP™)
Display Type DLP™ Chip, RGB optical shutter method
Resolution 1920 x 1080 pixels
Short Throw Lens 1-1.25 x zoom lens, F2.4~2.6, f= 18.65~23.32 mm
Long Throw Lens 1-1.25 x zoom lens, F2.4~2.6, f= 23.1~29 mm
Projection Lamp Lamp type 280W P-VIP lamp
Input Sources Video
HDMI x 2
YCbCr, YPbPr (Component Video) x 1
CVBS (Composite Video) x 1
S-Video x 1
PC x 1
Control
RS-232 (For computer) x1
IR Receiver (For remote) x 2
12V trigger output x2
USB x 1
Computer Compatibility VGA,SVGA, XGA, SXGA, UXGA
2D Lens Shift Ability 1/2 of screen height: Up 100%, Down 60%
(Short Throw Lens) 1/2 of screen height: Left 15%, Right 15%
2D Lens Shift Ability 1/2 of screen height: Up 140%, Down 60%
(Long Throw Lens) 1/2 of screen height: Left 15%, Right 15%
Digital Keystone Correction 2D correction
Projection Lens Zoom lens with manual focus and manual zoom adjustment
Screen Size (Short Throw Lens) 50 ~ 300 inches
Screen Size (Long Throw Lens) 40 ~ 300 inches
Short Throw Ratio (16:9) 1.33 ~ 1.66
Long Throw Ratio (16:9) 1.66 ~ 2.09
Projection Distance in 100” 2.9m ~ 3.7m
(Short Throw Lens)
Projection Distance in 100” 3.7m ~ 4.6m
(Long Throw Lens)
Video Enhance 3D Y/C separation in Composite Video
Projection Method Front / Rear Desktop, Front / Rear Ceiling
OSD Control Projector keypad
IR remote control
Video System NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/
EDTV480p/EDTV 576p/HDTV 720p/HDTV 1080i/HDTV 1080p
Dimensions (Short Throw Lens) 380 mm x 336 mm x 164 mm (L x W x H)
Dimensions (Long Throw Lens) 380 mm x 336 mm x 164 mm (L x W x H)
Weight (Short Throw Lens) 15.4 lbs (7.0 kg)
Weight (Long Throw Lens) 15.9 lbs (7.2 kg)
Power Supply 100 ~ 240 V at 50/60 Hz
Power Consumption 365W
Operating Temperature 5°C to 35°C
Lamp Warranty 90 days or 500 hours
Specifications are subjected to change without notice.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Release Version A
Download from Www.Somanuals.com. All Manuals Search And Download.
|
