INTEGRATED COMPACTOR
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at
In Canada, for assistance, installation or service, call: 1-800-807-6777 or visit our website at www.KitchenAid.ca
Table of Contents............................................................................................................2
W10242569A
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Installer: Leave Use and Care Guide with the homeowner.
Homeowner: Keep Use and Care Guide for future reference and for local electrical inspector’s use, if required.
4. Place the other 2 corner posts on the floor to the side of the
compactor. Grasp the sides of the compactor cabinet and put
compactor on its side on top of the corner posts. Remove the
shipping base from the bottom of the compactor.
Unpacking
WARNING
Excessive Weight Hazard
Use two or more people to move and install compactor.
Failure to do so can result in back or other injury.
A
B
IMPORTANT:
■
Do not grasp console to move compactor.
■
Begin in the room where the compactor will be located.
1. Remove compactor from shipping carton. Remove all
packaging materials such as tape and shipping pads. Use a
mild detergent and warm water to remove waxy residue
caused by shipping material. Dry thoroughly with a soft cloth.
For more information, see “Cleaning.”
A. Leveling legs
B. Shipping base
Location Requirements
2. Be sure the power cord is attached to the cord clip on the
rear of the compactor.
Product Dimensions
A
34¹⁄₈"
(86.7 cm)
A. Cord clip
3. Place the 2 corner posts from the carton on the floor near the
compactor. Open the compactor drawer and remove any
shipping materials or other items from the drawer. Do not
remove the compactor bag. Grasp the handle and raise the
front of drawer until it clears the drawer stops. Grasp sides of
drawer and lift drawer out of compactor. Place the drawer on
the 2 corner posts.
24"
(61 cm)
15"
(38.1 cm)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutout Dimensions
Electrical Requirements
WARNING
3" min.
(7.6 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
A
34¹⁄₄" min.
(87 cm)
24" min.
(61 cm)
18" min.
Do not use an extension cord.
(45.7 cm)
Failure to follow these instructions can result in death,
fire, or electrical shock.
15¹⁄₄" min.
(38.7 cm)
Recommended Grounding Method
A. Grounded electrical outlet must be a minimum
of 3" (7.6 cm) away from surrounding cabinets
or nearby walls as shown. It can be placed
either to the left or the right side of the
compactor.
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only, 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is
recommended that a separate circuit serving only this appliance
be provided.
Clearance Dimensions
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a three-
conductor cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Do not connect the
green (or green and yellow) wire to a live terminal.
A
B
A. Leave 6" (15.2 cm) of clearance space to the right side of
the compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor
in order to fully open or remove the compactor drawer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Undercounter Installation
NOTE: Proper installation is your responsibility. Make sure you
3. For model with cabinet, remove the plastic plugs from the
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
national and local codes and ordinances.
compactor cabinet top.
4. Move the compactor close to its final location.
5. Plug into a grounded 3 prong outlet.
6. Determine if you want the compactor frame or drawer front
Tools needed:
flush with the cabinet front.
Using the two #8-18 x ⁵ꢀ₁₆" screws, install the retaining
brackets to cabinet top as needed:
Gather the required tools and parts before starting installation.
■
■
■
■
Level
■
■
■
■
#2 Phillips screwdriver
Flat-blade screwdriver
⁵⁄₁₆" Box-end wrench
Utility knife
■
■
■
If the compactor frame is to be flush with the cabinet
front, place retaining bracket screws through “1.”
Tape measure
Pliers
If the compactor drawer front is to be flush with the
cabinet front, place retaining bracket screws through “3.”
Scissors
If the compactor is to be midway between “1” and “3,”
place the retaining bracket screws through “2.”
IMPORTANT:
■
Do not grasp control panel to move compactor.
A
B
■
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
■
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
3
2
1
Undercounter Installation
NOTE: Installation hardware is not provided with full cabinet
models.
1. Measure the height of your cabinet opening. The top of the
compactor should be at least ¹ꢀ₈" (3 mm) from the top of the
cabinet opening.
A. Countertop
B. Retaining bracket
The rear wheels are preset for a cabinet opening height of
34¹⁄₄" (87 cm) (Position 1).
7. Slowly lift the front slightly and roll compactor into the cabinet
opening.
To adjust for other cabinet opening heights:
Using the two #8-18 x ¹ꢀ₂" screws, fasten the retaining
brackets to the countertop with the mounting screws.
■
Loosen self-tapping screw just enough to clear stud from
hole in position “1.”
If brackets cannot be attached to the underside of
countertop, attach mounting clips to brackets. Fasten
compactor to cabinet front with mounting screws through
mounting clips.
■
Move the rear wheel and stud to position “2” or “3” as
needed for your cabinet opening measurement:
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
Countertop mounting
NOTE: To level the unit in position “3,” you may need to
add shims under the leveling legs.
■
Tighten screw. Repeat for other rear wheel.
A
B
B
C
1
2
3
C
A. Countertop
B. Retaining bracket
C. Mounting screw
A
D
A. Wheel bracket assembly
B. Cabinet
C. Locating stud
D. Self-tapping screw (pivot)
2. Use pliers to lower leveling legs away from cabinet. Adjust
legs so there will be a ¹⁄₈" (3 mm) to ¹ꢀ₄" (6.4 mm) space
between the top of the compactor and the top of the cabinet
opening. Stand the compactor upright.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabinet-front mounting
Installation
1. Remove the 2 rubber bumpers from the lower corners of the
inside drawer front. Set aside the bumpers and discard the
screws.
2. Align the bottom of the custom panel with the bottom of the
exterior drawer front and rest the panel on the rest tab.
NOTE: The bottom of the custom panel should not extend
below the bottom rest tab at the lower center of the exterior
drawer front.
C
D
A
B
3. Secure the custom panel to the exterior drawer front by using
four #8 x 1" wood screws from the inside drawer front.
4. Attach a 15" x ¹⁄₂" quarter-round filler along the top inside
edge of the drawer front using glue or screws.
A. Mounting clip
B. Cabinet
C. Retaining bracket
D. Mounting screw
A
8. Grasp sides of compactor drawer and place bottom of
drawer into tracks. Lift at the handle so drawer will go over
drawer stops. Close drawer. Check to see if drawer opens
freely. If the toe plate rubs against floor, see “Adjusting the
Toe Plate” for further instructions.
D
B
C
Adjusting the Toe Plate
D
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
2. Remove the drawer from the unit. (See Step 3 in the
“Unpacking” section.)
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4. Use scissors or utility knife to cut toe plate along line.
5. Replace drawer. If toe plate still rubs floor covering, repeat
steps 1-4.
A. Custom panel
B. 15" x ¹⁄₂" quarter round
C. Drawer front
D. Four #8 x 1" wood screws placement
Installing a Custom Panel
Dimensions
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be a minimum of ¹⁄₂" (13 mm)
thick.
29 ³⁄₈"
(74.6 cm)
15"
(
)
38.1 cm
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPACTOR USE
■
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
How Your Compactor Works
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
NOTE: The compactor drawer should be more than ¹⁄₂ full before
the compactor can begin to compress the load.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about ¹⁄₄ the size of its original bulk.
3. Close the drawer.
WHISPER QUIET® Plus System
The WHISPER QUIET® Plus system helps to maintain a quiet
home environment during compactor operation.
NOTE: The contents of the trash may affect the noise level of
your compactor. See “Compactor Use.”
Starting Your Compactor
1. Open container. Load trash.
2. Leave Key-Knob in ON position.
3. Set Solid Cycle switch to OFF.
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a “misload” and causes the ram to return to the “up”
position without compacting.
4. Close container.
5. Press foot-actuated START pedal to begin cycle.
Using Solid (Locked) Cycle
The Solid (Locked) Cycle extends the use of the bag by putting
constant pressure on the trash to keep it from springing back.
Regular use of solid cycle can increase bag capacity up to
25 percent.
During Solid Cycle, the ram will stay in the down position for
extra compacting. The drawer is locked and cannot be opened
when the ram is down.
Loading
For best results, use the Solid Cycle for at least 30 minutes at a
time.
IMPORTANT: Do not push items down into compactor with
hands or feet.
1. Open container. Load trash.
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
¹⁄₂ full before the compactor can begin to compress the load.
2. Set compactor Solid Cycle switch to ON.
1. Open the drawer. Lift and pull the handle or press the toe bar
to open the drawer.
NOTE: Pressing the toe bar opens the container only 3" to 6"
(7.6 cm to 15.2 cm), depending on the load.
3. Close container.
4. Press foot-actuated START pedal to begin cycle.
5. Container remains LOCKED until you RESET by pressing
foot-actuated START pedal.
2. Place trash in compactor.
■
Wrap or cover wet or messy trash.
■
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Air Filter or Freshener
Installing a New Bag
1. Set the Air Filter switch to ON. The fan creates air movement
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the “Assistance or Service” section.
in the compactor for odor removal.
NOTE: The charcoal Air Filter works only when the Key-Knob
is in the ON position.
IMPORTANT:
Before installing a new bag, be sure:
IMPORTANT: The air freshener will work with or without the
fan.
■
The drawer side is securely locked.
2. Set the Air Filter switch to OFF to turn off the fan.
■
The container is clean and free of debris.
1. Place folded bag into the drawer. Open bag and pull top
edges over the drawer top.
Removing a Filled Bag
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
2. Lock bag in place by pulling the four prepunched holes over
the bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
IMPORTANT: Do not push items down into compactor with
hands or feet.
3. Press inside of bag against the drawer bottom, sides and
1. Pull the drawer completely open.
corners for a smooth fit.
2. Remove top of bag from bag retainer buttons. Pull up all four
bag cuffs. Close bag with twist tie provided.
3. Push Side-Lock Latch down and tilt drawer side open.
4. Lift out bag.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPACTOR CARE
Your new compactor is designed to give you many years of
Cleaning Inside the Drawer
dependable service. However, there are a few things you are
expected to do in order to properly maintain your compactor.
This section will tell you how to clean and care for your
compactor.
NOTE: You may want to wear gloves since there may be bits of
glass in the drawer.
1. Remove the bag. See the “Removing a Filled Bag.”
2. Press down on the lever-action lock (or Side-Lock latch).
Changing the Air Filter or Freshener
It is recommended that you use either the charcoal air filter or the
air freshener in the filter compartment. The solid air freshener
system is an alternative to the air filter and is designed to control
odors that might develop in the trash.
To order the correct replacement charcoal filters or air fresheners,
call the toll-free number listed on the cover or in the “Assistance
or Service” section.
3. Hold the lever-action lock down and tilt the side of the drawer
1. Insert fingertips in the air filter cover and pull until the side
out until the lock clears the drawer front.
tabs release. Then, lift the cover to release the bottom tabs.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
2. Remove the air filter by pulling the top edge of the filter. The
filter should pull out easily. Throw away used filter.
OR
Remove the air freshener by simply lifting out of the filter
compartment. Throw away used freshener.
4. Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted
position.
6. Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7. Latch the drawer side by pushing up the lever-action lock (or
Side-Lock Latch).
3. To replace air filter, push the replacement filter into place.
Cleaning Inside the Cabinet
OR
To replace the air freshener, place the replacement in the filter
compartment.
NOTE: You may want to wear gloves since there may be bits of
glass in the cabinet.
4. Insert the bottom tabs of the air filter cover and push in until
1. Pull the drawer out until it stops.
the side tabs snap into place.
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
Cleaning
Before cleaning the compactor, turn the Key-Knob (or Key-
Switch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
Cleaning Exterior Surfaces
1. Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
2. Lift the front of the drawer to clear the stops.
2. Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Grasp the drawer on the sides and pull it out the rest of the
Cleaning the Ram
way. Set the drawer down gently.
NOTE: You may want to wear gloves since there may be bits of
glass on the ram cover.
1. Wipe glass particles off of the ram cover with a cloth or paper
towels.
2. Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
4. Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum
designed to pick up liquids.
Cleaning Before a Vacation
5. Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children’s reach.
6. To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Trash is not compacting
The drawer won’t open
■
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted.
■
Is the ram all the way up? Drawer will open only when ram is
fully raised.
To raise the ram on models with a Key-Knob (or Key-
Switch): Turn the Key-Knob (Key-Switch) to START and
release. See “Starting Your Compactor.”
Your compactor won’t operate
■
■
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
To raise the ram on models with push button controls:
Press OFF, and then press ON. See “Starting Your
Compactor.”
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■
■
■
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
■
■
Is the drawer completely closed? Close the drawer firmly
and start the compactor again.
There is not enough compaction or force
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See “Starting Your Compactor.”
Do you use the compacting cycle frequently enough?
Compacting works best when only a few items are loaded.
■
Did you press ON before pressing START? Press ON
before pressing START (on some models). See “Starting Your
Compactor.”
Bottles don’t break
How often do you notice this? Bottles will not break every
time. The thickness of the bottle’s glass and the content of
the trash load below it may keep the bottle from breaking.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
In Canada
Call the KitchenAid Canada Customer eXperience Centre toll
free: 1-800-807-6777.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Our consultants provide assistance with:
■
■
■
■
■
Features and specifications on our full line of appliances.
If you need replacement parts
Warranty information.
Use and maintenance procedures.
Accessory and repair parts sales.
If you need to order replacement parts, we recommend that you
use only factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new KITCHENAID® appliance.
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
To locate factory specified parts in your area, call us or your
nearest designated service center.
In the U.S.A.
For further assistance
Call the KitchenAid Customer eXperience Center
If you need further assistance, you can write to KitchenAid
Canada with any questions or concerns at:
toll free: 1-800-422-1230
Our consultants provide assistance with:
KitchenAid Canada
■
■
■
■
■
Features and specifications on our full line of appliances.
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga ON L5N 0B7
Installation information.
Use and maintenance procedures.
Accessory and repair parts sales.
Please include a daytime phone number in your correspondence.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Accessories
To ensure the proper functioning of your compactor, use
KITCHENAID® replacement parts only. To order replacement
parts or accessories, call 1-800-462-3819 and ask for the
appropriate part number listed below or contact your authorized
KitchenAid dealer. In Canada, call 1-800-807-6777.
■
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in the United States.
To locate the KitchenAid designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Replacement Parts
Replacement Bags - Call for Part Number.
Charcoal Air Filters - Order Part Number 4151750.
Air Fresheners (scent):
Order Part Number 9872166GA (Fresh Green Apple)
Order Part Number 9872166L (Lavender)
Order Part Number 9872166LG (Lemon Grove)
For further assistance
If you need further assistance, you can write to KitchenAid with
any questions or concerns at:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Color Panel Kits and Handles
Please include a daytime phone number in your correspondence.
See section “Installing a Custom Panel” for custom panel
dimensions.
Color Panel with Handles:
Order Part Number 4396299 (Cobalt Blue)
Order Part Number 4396300 (Empire Red)
Order Part Number 4396301 (Majestic Yellow)
Order Part Number 4396296 (Black)
Order Part Number 4396297 (White)
Order Part Number 4396298 (Biscuit)
Handles:
Order Part Number 9871564 (Brushed stainless steel)
Order Part Number 9871564W (White)
Order Part Number 9871564B (Black)
Order Part Number 9871564T (Biscuit)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
KITCHENAID® COMPACTOR WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KitchenAid Canada (hereafter “KitchenAid”) will pay for factory specified parts and repair
labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company.
30 DAY LIMITED WARRANTY ON THE CHARCOAL FILTER AND AIR FRESHENER
For thirty days from the date of purchase, when the compactor is installed, operated and maintained according to instructions attached
to or furnished with the product, KitchenAid will provide a replacement filter or air freshener if the original filter or air freshener fails due
to defects in materials or workmanship.
ITEMS KITCHENAID WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by KitchenAid.
5. Replacement parts or repair labor costs for units operated outside the United States or Canada.
6. Pickup and delivery. This major appliance is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service in remote locations.
9. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,
call 1-800-807-6777.
9/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
W10242569A
2/10
Printed in U.S.A.
© 2010. All rights reserved.
® Registered Trademark/TM Trademark of KitchenAid, U.S.A., KitchenAid Canada licensee in Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|