2150
Eastern Avenue.
Gallipolis, Ohio 45631
ROTARY TILLER
OPERATOR MANUAL
Part No 999995
Download from Www.Somanuals.com. All Manuals Search And Download.
TO THE PURCHASER
This manual contains valuable information about your
new King Kutter II Rotary Tiller. It has been carefully prepared
to give you helpful suggestions for operating, adjusting, ser-
vicing and ordering repair parts.
Keep this manual in a convenient place for quick and
easy reference. Study it carefully. You have purchased a de-
pendable and sturdy tiller, but only by proper care and opera-
tion can you expect to receive the service and long life de-
signed and built into it.
Sometime in the future your tiller may need new parts to
replace those that are worn or broken. If so, go to your dealer
and provide him with the model and part number.
Customer Information
Name ______________________________________________
Purchased From ______________________________________
Date Purchased ______________________________________
Model No. ___________________________________________
Serial No. ___________________________________________
3
Download from Www.Somanuals.com. All Manuals Search And Download.
It is the purchaser and/or operator’s responsibility to….
Read and understand the information contained in this
manual.
Operate, lubricate, assemble and maintain the
equipment in accordance with all instructions and
safety procedures in this manual.
Inspect the equipment and replace or repair any
parts that are damaged or worn which under contin-
ued operation would cause damage, wear to other
parts, or cause a safety hazard.
Return the equipment or parts to the authorized
King Kutter dealer, from where it was purchased, for
service or replacement of defective parts that are
covered by warranty. (The King Kutter Factory may
inspect equipment or parts before warranty claims
are honored.)
Payment of all costs incurred by the dealer for traveling
to or transporting the equipment for warranty inspection
and or claims.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
ITEM
PAGE
Safety.........................................................................6
Assembly Instructions................................................8
Before Putting Into Service ........................................8
Safety Training......................................................... 11
Transportation Safety...............................................15
Attaching To Tractor .................................................16
Sizing PTO...............................................................18
Operating Instructions..............................................19
Maintenance ............................................................20
Maintenance Safety .................................................20
Safety Decal's And Locations...................................22
Replacement Parts ..................................................28
PTO Shaft Parts.......................................................30
Gearbox Parts.................................................... …..32
Warranty ………………………………………………...36
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ AND FOLLOW THE INSTRUC-
TIONS IN THIS MANUAL AND ESPE-
CIALLY IN THE SAFETY SECTION.
FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY OR DEATH.
TAKE NOTE! THIS SAFETY ALERT
SYMBOL FOUND THROUGHOUT
THIS MANUAL IS USED TO CALL
YOUR ATTENTION TO INSTRUC-
TIONS INVOLVING YOUR PERSONAL
SAFETY AND THE SAFETY OF OTH-
ERS.
THIS SYMBOL MEANS
ATTENTION!
BECOME ALERT!
YOUR SAFTEY IS INVOLVED
SIGNAL WORDS:
The signal words DANGER, WARNING and CAUTION are used with the
safety messages in this manual and with each safety signs. They are defined as
follows:
DANGER: Indicates an immediate hazardous situation that, if not avoided,
could result in serious injury or death. This signal word is to be limited to the
most extreme situations typically for machine components that, for functional
purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided,
could result in serious injury or death, and includes hazards that are exposed
when guards are removed. It may also be used to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practice.
If you have any questions not answered in this manual or require additional cop-
ies or the manual is damaged, please contact your dealer or King Kutter, Inc.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT SAFETY GUIDELINES
Safety of the operator and bystanders is one of the main concerns in designing and devel-
oping a tiller. However, every year accidents occur which could have been avoided by a
few seconds of thought and a more careful approach to handling equipment. You, the op-
erator, can avoid many accidents by observing the following precautions and insist those
working with you, or for you, follow them.
In order to provide a better view, certain photographs or illustrations in this manual may
show an assembly with a safety shield removed. However, equipment should never be op-
erated in this condition. Keep all shields in place. If shield removal becomes necessary for
repairs, replace the shield prior to use.
Replace any safety sign that is not readable or missing. Location of such safety signs are
indicated in this manual.
Never use alcoholic beverages or drugs that can hinder alertness or coordination while op-
erating this equipment. Consult your doctor about operating this machine while taking pre-
scription medications.
Under no circumstances should children under the age of 18 be allowed to work
with this equipment. Do not allow persons to operate or assemble this unit until
they have read this manual and have developed a thorough understanding of the
safety precautions and how it works. Review the safety instructions with all users annu-
ally.
This equipment is dangerous to children and persons unfamiliar with its operation. The op-
erator should be a responsible, properly trained and physically able person familiar with
farm machinery and trained in this equipment’s operations. If the elderly are assisting with
farm work, their physical limitations need to be recognized and accommodated.
Use a tractor equipped with a Roll Over Protective System and seat belts. (ROPS)
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely,
is in question- DON’T TRY IT.
Do not modify the equipment in any way. Unauthorized modification could result in serious
injury or death and may impair the function and life of the equipment.
In addition to the design and the confirmation of this implement, including safety signs and
safety equipment, hazard control and accident prevention are dependent upon the aware-
ness, concern, prudence, and proper training of personnel involved in the operation, trans-
port, maintenance, and storage of the machine. Refer also to safety messages and opera-
tion instruction in each of the appropriate sections of the tractor and tiller manuals. Pay
close attention to the safety signs affixed to the tractor and the tiller.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTARY TILLER ASSEMBLY INSTRUCTIONS
STEP 1 With rotary tiller still in crate, lay flat on a level surface. Cut banding
straps on the two (2) up right crate posts.
STEP2 Remove the top & upper side sections of the crate, leaving the rotary tiller
resting on the bottom section. You may take the tiller off of crate but you must
swing stand arm down and lock in position. (See Figure D) Snap stand out of
clip, straight out, then swivel the stand down to locked position.
STEP3 Remove tie wire holding the PTO shaft and set aside PTO.
STEP 4 Attach tiller according to your tractors manual and using the instructions on
pages16and17.
STEP5 Install tail back plate chain.
STEP 6 Install PTO shaft as outlined in the Attaching to Tractor Section, pg 16-
19.
Note: The safety chains on the PTO shaft should be attached to the tractor and
tiller to prevent the plastic safety shield from rotating.
BEFORE PUTTING ROTARY TILLER INTO SERVICE
(IMPORTANT- INSTRUCTIONS PRIOR TO START UP)
SHIPPED WITH OIL IN GEAR BOXES
SHIPPED WITHOUT GREASE IN GREASE FITTINGS.
UNIT MUST BE SERVICED BEFORE USING.
•
•
In Gearboxes use gear oil (type GL5-85W 140 or Triple Zero
Grease; which can be poured, and has "EP" i.e. "Extreme
Pressure" additives.)
For all Grease Fittings use TYPE/grade II tube grease.
STEP1
STEP2
STEP3
STEP 4
STEP 5
Placerotarytillersothatthedeckissecureandlevel.
Remove1/2‖PipePlug(Locatedattopoftransmissiongearbox). SeeFigureA.
Fillgearboxusinggearoiluntilgearboxisapproximately1/2full. SeeFigureB.
Replace and tighten the 1/2‖ pipe plug and clean away any excess oil.
See Figure C.
Remove 1/2‖ Pipe Plug (Located at top of side gearbox, See Figure E on page 10)
and the 1/8" check plug (Located in side of the side gearbox) if oil comes out of check
plug hole, replace plug immediately and go to STEP 7. If oil doesn’t come out go to
STEP6.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6
STEP 7
STEP 8
Fill side gearbox using gear oil until the oil begins to overflow from the
check plug hole. See Figure F on next page.
Replace and tighten the 1/2‖ vent plug and the 1/8" check plug. Clean
away any excess oil. See Figure G on next page.
Grease the grease fitting on the "out-board hub," the two (2) grease fittings
on the PTO universal joints, the two (2) grease fittings on the PTO safety
shield and the inner surface portion of the PTO shaft. See Figures H, I
and J on next page.
CAUTION:
DO NOT over fill gearbox. This could cause damage to oil seals and can cause permanent damage
to the gearbox. This issue will not be covered under warranty.
Figure A
Figure C
Figure B
Figure D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure E
Figure F
Figure G
Figure H
Figure I
Figure J
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY TRAINING
Safety is a primary concern in the design and manufacturing of our product. Un-
fortunately, our efforts to provide safe equipment can be wiped out by a single
careless act of an operator or bystander.
In addition to the design and configuration of equipment, hazard control and ac-
cident prevention are dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation, transport, maintenance
and storage of this equipment.
It has been said, ― The best safety device is an informed, careful operator.‖ We
ask you to be that kind of operator. It is the operator’s responsibility to read and
understand all safety and operating instructions in the manual and to follow
them. Accidents can be avoided.
Working with unfamiliar equipment can lead to careless injuries. Read this man-
ual, and the manual for your tractor, before assembly or operating, to acquaint
yourself with the machines. If this machine is used by any person other than
you, or is loaned or rented, it is the rotary tiller owner’s responsibility to make
certain that the owner's manual be available to the operator prior to operating:
1- Reads and understands the operator’s manuals.
2- Is instructed in safe and proper use.
Know your controls and how to stop the tractor, engine, and tiller quickly in an
emergency. Read this manual and the one provided with your tractor.
Train all new personnel and review instructions frequently with existing workers.
Be certain only a properly trained and physically able person will operate the
machinery. A person who has not read and understood all operating and safety
instructions is not qualified to operate the machine. An untrained operator ex-
poses himself and bystanders to possible serious injury or death. If the elderly
are assisting with farm work, their physical limitations need to be recognized and
accommodated.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARTION
Never operate the tractor and tiller until you have read and completely under-
stand this manual, the Tractor Operator’s Manual, and each of the safety mes-
sages found on the safety signs on the tractor and tiller.
Personal protection equipment including hardhat, safety glasses, safety shoes, and gloves
are recommended during assembly, installation, operation, adjustment, maintenance, re-
pairing, removal, or moving the implement. Do not allow long hair, loose fitting clothing, or
jewelry to be around equipment.
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING
LOSS! Tractors with or without tillers attached can often be noisy enough to cause perma-
nent, partial hearing loss. We recommend that you wear hearing protection on a full-time
basis if the noise in the operator’s position exceeds 80 db. Noise over 80 db on a long-
term basis can cause severe hearing loss. Noise over 90 db adjacent to the operator over
a long-term basis may cause permanent, total hearing loss. NOTE: Hearing loss from loud
noise (from tractors, chain saws, radios, and other such sources close to the ear) is cumu-
lative over a lifetime without hope of natural recovery.
Operate the tiller only with a tractor equipped with an approved Roll-Over-Protective Sys-
tem (ROPS). Always wear your seat belt. Serious injury or even death could result from
falling off the tractor — particularly during a turnover when the operator could be pinned
under the ROPS or the tractor.
Clear area to be tilled of stones, branches or other debris that might be thrown or entan-
gled in the tiller, causing injury or damage.
Operate only in daylight or good artificial light.
Ensure tiller is properly mounted, adjusted and in good operating condition.
Ensure that all safety shielding and safety signs are properly installed and in good condi-
tion.
STARTING AND STOPPING SAFETY
Check the tractor master shield over the PTO stub shaft. Make sure it is in good condition
and fastened securely to the tractor. Purchase a new shield if old shield is damaged or
missing.
All tractors that are not equipped with a ―live‖ power takeoff (PTO) need to be equipped
with an over-running PTO clutch. These are available through most farm equipment
stores. NOTE: The addition of an over-running PTO clutch may change the length of the
PTO driveline required. Pay extra attention to the instructions on the PTO Driveline Instal-
lation. Be sure that the driveline system guarding is adequate.
Tiller operating power is supplied from the tractor PTO. Refer to your tractor manual for
PTO engagement and disengagement instructions. Know how to stop tractor and tiller
quickly in case of an emergency.
When engaging PTO, the engine RPM should always be at idle speed. Once engaged and
ready to start tilling, raise PTO speed to 540-RPM and maintain throughout tilling opera-
tion.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY
The use of this equipment is subject to certain hazards that cannot be protected
against by the mechanical means or product design. All operators of this equip-
ment must read and understand this entire manual, paying particular attention to
safety and operating instructions, prior to using. If there is something in this
manual you do not understand, ask your supervisor, or your dealer, to explain it
to you.
Most accidents occur because of neglect or carelessness. Keep all helpers and
bystanders at least several hundred feet from an operating rotary tiller. Only
properly trained people should operate this machine.
When machine is operated in populated areas where thrown objects could injure
persons or property, operation must be stopped when anyone comes within
several hundred feet.
The majority of the accidents involve entanglement on the driveline, injury of by-
standers by the objects thrown by the rotating tines, and operators being
knocked off the tractor by low hanging limbs and then being run over by the
tiller. Accidents are most likely to occur with machines that are loaned or rented
to someone who has not read the owner’s manual and is not familiar with a ro-
tary tiller.
The rotary tiller is designed for use only on tractors with the power take- off
(PTO) turning at 540-RPM.
Install and secure all guards and shields before starting or operating. The tiller
tines, driveline guards and tractor, shields should be used and maintained in
good working condition. They should be inspected carefully, at least daily, for
missing or broken chain links, shields, or guards. (Worn items must be replaced
at once to reduce possibility of injury.)
Disengage power takeoff (PTO) and place transmission in neutral before at-
tempting to start engine.
Many varied objects, such as wire, cable, rope, or chains, can become entan-
gled in the operating parts of the tiller. These items could then swing outside the
housing at greater velocities than the tines. Such a situation is extremely haz-
ardous. Inspect the cutting area for such objects before tilling. Remove any like
objects from the site.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Never allow the tilling tines to contact such items. Never assume an area is
clear. Always Check!
Always stop the tractor, disengage PTO, set brake, shut off the tractor engine,
remove the ignition key, lower implement to the ground and allow rotating pieces
to come to a complete stop before dismounting tractor. Never leave equipment
unattended with the tractor running.
Never place hands or feet under tiller with tractor engine running or before you
are sure all motion has stopped. Stay clear of all moving parts.
Do not reach or place any part of your body under equipment until it is blocked
securely.
Do not allow riders on the rotary tiller or tractor at anytime. There is no safe
place for any riders.
Do not operate unless all personnel, livestock, and pets are several hundred
feet away to prevent injury by thrown objects.
Never operate tractor and rotary tiller under trees with low hanging limbs. Op-
erators can be knocked off the tractor and then run over by the rotating tines.
The rotating parts of this machine have been designed and tested for rugged
use. However, they could fail upon impact with heavy, solid objects such as steel
guardrails and concrete abutment. Such impact could cause the broken objects
to be thrown outward at very high velocities. To reduce the possibility of property
damage, serious injury, or even death, never allow the tilling tines to contact
such obstacles.
Stop rotary tiller and tractor immediately upon striking an obstruction. Turn en-
gine off, remove key, inspect and repair any damage before resuming operation.
Stay alert for uneven terrain, holes, rocks, and roots and other hidden hazards.
Keep away from drop-offs and hazards that could cause roll over. Use extreme
care and maintain minimum ground speed when transporting or operating on
hillsides, over rough ground and when operating close to ditches or fences. Be
careful and slow down when turning sharp corners and changing direction on
slopes. Do not start or stop suddenly on slopes. Avoid operation on steep
slopes. In extremely uneven terrain, rear wheels weights, front tractor weight,
and/or tire ballast should be used to improve stability.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Pass rotary tiller diagonally through sharp dips and avoid sharp drops to prevent
―hanging up‖ tractor and rotary tiller. Practice will improve your skills in maneu-
vering on rough terrain. Always cut down slopes, never across the face. Always
check tractor manual for proper use on slopes.
When using a unit, a minimum 20% of tractor and equipment weight must be on
tractor front wheels. Without this weight, tractor could tip over, causing personal
injury or death. The weight may be attained with a front- end loader, front wheel
weights, ballast in the tires or front tractor weights. When attaining a minimum
20% of tractor and equipment weight on the front wheels, you must not exceed
the ROPS weight certification. Weigh the tractor and equipment. Do not guess
or estimate!
TRANSPORT SAFETY
Comply with state and local laws governing highway safety and movement of
farm machinery on public roads.
The use of flashing amber lights is acceptable in most localities. However, some
localities prohibit their use. Local laws should be checked for all lighting and
marking requirements.
At all times, when driving the tractor and equipment on the road or highway un-
der 20mph (32kph) use flashing amber warning lights and a slow moving vehicle
(SMV) identification emblem. Do not exceed 20 mph (32 kph). Reduce speed
on rough roads and surfaces.
Plan your route to avoid heavy traffic.
Always install transport locks, pins or brackets before transporting.
Do not drink and drive.
Be a safe and courteous driver. Always yield to oncoming traffic in all situations,
including narrow bridges, intersections, etc. Watch for traffic when operating
near or crossing roadways.
Turn curves or go up or down hills only at a low speed and at a gradual steering
angle. Make certain that a least 20% of the tractor’s weight is on the front
wheels to maintain safe steerage. Slow down on rough or uneven surface. Al-
ways check tractor manual for proper use on slopes.
Use extreme care and maintain minimum ground and when operating close to
ditches or fences. Be careful when turning sharp corners.
Never allow riders on either tractor or tiller.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR
WARNING
Never stand between
tractor and rotary tiller
while backing up tractor
to the hitch.
STEP 1 Attach to tractor's category 1 three point hitch as described in
the Tractor's Operator’s Manual.
WARNING
Failure to install retaining clip on gearbox input shaft would allow driveline to
swing freely if bolt is sheared causing possible injury or death.
STEP 2
Determine if the PTO shaft needs to be shortened.
NOTE:
Due to the many variations in the tractor hitch points and distances between
equipment gearbox input shaft and tractor PTO out put shafts, some combina-
tions may require PTO shafts to be shortened as described by the following
steps.
STEP 3
Raise and lower rotary tiller in order to locate the shortest distance between
equipment gearbox input shaft and tractor PTO output shaft. With the rotary
tiller in the shortest distance position shut down the tractor and SECURELY
BLOCK ROTARY TILLER IN POSITION.
STEP 4
Pull apart PTO shaft and attach outer section to tractor PTO output shaft.
NOTE: Be sure to pull on PTO shaft section to ensure yoke has locked into
place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR continued....
STEP 5
Place and hold inner PTO shaft section next to outer section and check if PTO
shaft is too long. Each section should end approximately 3 inches short of
reaching u-joint shield on the opposite section. If the shaft is too long measure
3 inches back from each u-joint shield and mark the other shaft section. Be sure
to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft sections at
this time.
STEP 6
Raise rotary tiller and remove blocking. Raise and lower rotary tiller in order to
locate the longest distance between equipment input shaft and the tractor PTO
output shaft. With the rotary tiller in the longest distance position shut down the
tractor and SECURELY BLOCK THE ROTARY TILLER IN POSITION.
STEP 7
As in step 5 hold PTO shaft sections together and check for a minimum of 6
inches of overlap. If PTO shaft has been marked for cutting the overlap is the
distance measured between the two marks. If the PTO shaft has less than a 6
inch overlap, DO NOT USE. Contact your authorized King Kutter II Dealer.
NOTE
If the PTO shaft length is too long go to SIZING PTO SHAFT (pg. 18)
STEP 8
Apply any multi-purpose grease to the outside of the male (inner) PTO shaft
section. Assemble PTO shaft and install on rotary tiller and tractor.
STEP 9
Pull on tractor side of PTO shaft yoke to be sure it has locked in place. Make
certain PTO shaft shielding is in place and good working condition.
STEP 10
The PTO shaft shield is a non-rotating design and must be secured prior to
equipment use. Using the chain on each yoke shield attach to a fixed object on
the tractor and equipment ends that will not allow the PTO shaft shield to rotate
during operation.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SIZING PTO SHAFT
STEP 1
Cutting the PTO shaft to length. NOTE:
Be sure to cut equal lengths of each
PTO shaft section. Clamp end of PTO
shaft in a vice and cut off shield where
marked. (Figure 1-A & 1-B)
Figure 1-A
STEP 2
Using cut section of the shield as a
guide cut shaft off the same amount.
(Figure 2)
STEP 3
Repeat steps 1 and 2 for other PTO
shaft section.
STEP 4
Figure 1-B
Use a file to deburr PTO shafts. Clean
up all chips, burrs and filings from both
ends of the PTO shaft.
Note: If you shear the bolt that attaches
the PTO shaft to the gearbox re-
place with a grade 2 bolt only. Re-
placement with another grade of
bolt will void your warranty and may
cause terminal damage to the PTO
shaft, gearbox, or tractor.
Figure 2
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
STEP 1
Before each use perform the maintenance described in maintenance section (page
20).
STEP2
Read, understand, and follow the information on safety training, preparation, starting
and stopping safety, operational safety, transport safety warning sections of this man-
ual (pages 12 thru 15).
STEP 3
With the rotary tiller positioned on level ground, adjust the tractor lift arms so that
when lifted, the rotor bar remains parallel to the ground.
STEP 4
With the rotary tiller attached to the tractor, raise and support the tiller with suitable
blocks. Adjust the skids, located on the sides of the tiller. The adjustment bolts for
both right and left sides should be positioned in the same adjustment hole. This al-
lows the tiller to till the same depth on each side. Adjust the back plate, with regulat-
ing chain, until the desired mulching effect is found.
Note: Never attempt to adjust the rotary tiller while the tractor is
running.
STEP 5
Raise the tiller and remove the blocks. Lower the tiller to the ground.
STEP 6
With the tractor at idle RPM and the tiller lifted off of the ground, engage PTO and
slowly advance throttle to 540 PTO RPM. NOTE: Rotary tiller is designed to run at
540 PTO RPM only.
STEP 7
Select a low gear for the tractor and begin to move forward. Tractor
ground speed is to be controlled by gear selection only and not engine
speed. As the tractor moves forward, slowly lower the tiller down. Allow the
tiller tines to gradually engage the ground.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Do not allow the tractor engine or rotary tiller to bog down or stall. This
causes undue wear and tear on the tiller and tractor. If this continues to happen
reduce ground speed and raise tilling depth of rotary tiller. Never attempt to re-
move objects from the rotor bar until the tractor has been shut down and the
tiller tines have completely stopped.
WARNING
Never travel at a fast ground speed while using the tiller, this could damage it.
Never attempt to turn the tractor or travel in reverse with the PTO engaged and
the tiller in the ground. Always raise the tiller out of the ground when backing
up or attempting to turn. Failure to due so may cause damage to the tiller.
STEP 8
After each use clean all debris from the tiller tines. Replace any missing or illegible
safety decals. Inspect for any damaged or worn parts and replace before next use.
Store rotary tiller in a dry environment.
MAINTENANCE
1). Periodically check and maintain proper gear oil level.
2). Every 8 hours, (1) grease "out-board hub", (2) PTO shaft universal joints, (3)
PTO shaft safety shield and (4) PTO telescoping surface.
NOTE: Use only a grade Type II tube grease.
NOTE: Do not grease the slip clutch assembly.
3). Before each use check to make sure all safety shields are installed and working
properly.
4). Check tiller tines for cracks and breaks before every use.
5). Periodically check all nuts and bolts to insure they are tight and secure.
6). Periodically loosen torque spring bolts and allow slip clutch to slip for approxi-
mately two (2) revolutions. Loosen the bolts until the springs lose contact with
the flange yoke. This ensures that the slip clutch is not in a "locked" position.
7). Make sure that the clutch slips.
8). To retighten the slip clutch, tighten the torque spring bolts until the nut makes
contact with the flange yoke and further tighten one and a half turns (1-1/2).
This is a good starting point , further adjustments may need to be made based
on soil conditions.
NOTE: Do not over or under tighten slip clutch assembly or damage may occur.
MAINTENANCE SAFETY
Good maintenance is your responsibility. Poor maintenance is an invita-
tion to trouble.
Follow good shop practices.
Keep service area clean and dry.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Be sure electrical outlets and tools are properly grounded
Use adequate light for the job at hand.
Make sure there is plenty ventilation. Never operate the engine of the towing
vehicle in a closed building. The exhaust fumes may cause asphyxiation.
Before working on this machine, disengage the PTO, shut off the engine, set the
brakes, and remove the ignition keys.
Be certain all moving parts on attachments have come to a complete stop be-
fore attempting to perform maintenance.
Never work under equipment unless it is blocked securely.
Always use personal protection devices such as eye, hand and hearing protec-
tors, when performing any service or maintenance.
Frequently check tiller tines. They should be sharp, free of nicks and cracks and
securely fastened.
Periodically tighten all bolts, nuts, and screws and check that all cotter pins are
properly installed to ensure unit is in safe condition.
When completing a maintenance or service function, make sure all safety
shields and devices are installed before placing unit in service.
After servicing, be sure all tools, parts and service equipment are removed from
tiller.
Do not allow debris, grease or oil to build up on any deck or platform.
Where replacement parts are necessary for periodic maintenance and servicing,
genuine factory replacement parts must be used to restore your equipment to
original specifications.
The manufacturer will not be responsible for injuries or damages caused by use
of unapproved parts and/or accessories.
A fire extinguisher and the first aid kit should be kept readily accessible while
performing maintenance on this equipment.
STORAGE SAFETY
Following operation, or when unhooking the tiller, stop the tractor, set the
brakes, disengage the PTO, shut off the engine and remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it can be exposed to direct contact to livestock for
long periods of time. Damage and livestock injury could result.
Make sure all parked machines are on a hard, level surface and engage all
safety devices.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGN LOCATIONS
The types of safety signs and locations on the equipment are shown in the illustration
below. Good safety requires that you familiarize yourself with the various safety signs,
the type of warning and the area, or particular function related to that area, that re-
quires your SAFTY AWARENESS.
Top View
Note: The numbers represent the safety decals on the following pages.
REMEMBER: If safety signs have been damaged, removed, become illegible or parts
have been replaced without signs, new safety signs must be applied. New safety
signs are available from your authorized dealer, distributor or factory.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL NO.
DESCRIPTION
SN# XXXXXXXXXX
6
7
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TILLER: EXPLODED VIEW
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TILLER: PARTS LIST
Ref.
No.
Part Name
TG-48
TG-60
380108
310085
310086
505116
505025
505030
505002
505006
TG-72
380108
310085
310086
505116
505025
505030
505002
505006
1
2
Lift Arm Brace
380108
Lift Arm (Left hand)
Lift Arm (Right hand)
310085
310086
505116
505025
505030
505002
505006
505036
3
4
Tail Rod Assembly
5
Center Piece Kit
6
Lift Arm Spacer Kit
7
Tine Pkg. (1-Right & 1- Left) w/ bolts
Tine Pkg. (3-Right & 3- Left) w/ bolts
4’ Complete Tine Pkg. (36 pcs.)
5’ Complete Tine Pkg. (42 pcs.)
6’ Complete Tine Pkg. (54 pcs.)
Tine Bolt Pkg. (12 pcs.)
Tine Bolt Pkg. (72 pcs.)
Tine Bolt Pkg. (84 pcs.)
Tine Bolt Pkg. (108 pcs.)
Skid Assembly (Left Hand)
Skid Assembly (Right Hand)
Chain & Shackle Kit
7
7
7
505042
505012
505084
7
505054
505012
8
505012
505072
8
8
8
505108
505050
505057
505143
184067
184069
500001
402053
402052
402054
184070
147122
505022
9
505050
505057
505143
184064
184069
500001
402038
402041
402039
184070
147122
505022
505050
505057
505143
184066
184069
500001
402042
402046
402043
184070
147122
505022
10
11
12
13
14
15
16
17
18
19
20
Top Gearbox Assembly
Side Gearbox Assembly
Lift Pins CAT. 1 (Pkg. 2)
Rotor Assembly
Back Plate Assembly
Frame Assembly
Outboard Hub Assembly (TG Series)
PTO Shaft
Support Stand Assembly
29
Download from Www.Somanuals.com. All Manuals Search And Download.
22” PTO 147122
Ref.
No.
Part Name
147122
Part No.
1
2
Safety Shield
Roll Pin
124311
170120
151045
151050
151035
151090
151091
170015
170110
500140
140226
140221
140220
140224
140216
140219
196008
3
Male Tube End Yoke
4
Female Tube End Yoke
Tractor End Yoke
5
6
Inner Tube 14 Series
7
Outer Tube 14 Series
8
Cross Kit # 4
9
Quick Disconnect Pin
10
11
12
13
14
15
16
16
Clutch Spring w/ Compression Bolts & nuts (Pkg. 8)
Flanged Yoke
Bushing
Friction Hub
10 x 70 Bolt
Pressure Plate (Outer)
Friction Disc for 6‖ Slip Clutch (4-3/4‖ OD x 2-11/16‖ ID)
Friction Disc for 7‖ Slip Clutch (5-1/2‖ OD x 3-5/16‖ ID)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TG SERIES OUT-BOARD HUB 184070
Ref.
No.
Part Name
184070
1
2
3
4
5
6
7
8
9
Hub Housing
Cap
902341
902342
902019
505017
902345
902011
902010
902009
902349
Self Aligning Ball Bearing (1310)
Seal Double Lip (Pkg. 2)
Bolt M-6 -16
Bolt M-12 –25
Lock washer M-12
Washer
Grease Zerk 1/4‖
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TG SERIES GEARBOX 184069
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TG SERIES SIDE GEARBOX PARTS LIST
Ref.
No.
Part Name
Part
Number
1
Retaining Ring 90mm
902005
2
Retaining Ring 40mm
Pressure Plate Plug 1/2‖ - 14 NPT
Sq. Hd. Plug 1/4‖ - 18 NPT
Flat Washer (Main)
Lock washer M-12
Bolt M-12-25
902006
902007
902008
902009
902010
902011
502247
502296
502207
902015
902016
505017
902018
902019
902021
902022
902020
902001
902002
902003
902004
3
4
5
6
7
8
Bolt M-8-16 (Pkg. 12)
Bolt M-10-25 (Pkg. 6)
Bolt M-10-20 (Pkg. 6)
Spacer (Output)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Spacer (Input)
Seal Double Lip (Pkg.2)
3210 Double Bearing (Ball)
1310 Self Aligning Bearing (Ball)
Gear -34 Teeth
Gear –16 Teeth
Gear –28 Teeth
Cover
Side Box Outboard Hub Housing
Housing
Gasket
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TG SERIES TOP GEARBOX ASSEMBLY
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TG SERIES TOP GEARBOX PARTS LIST
Ref.
No.
Part Name
Part
Number
1
Retaining Ring 72mm
902301
2
3
Retaining Ring 40mm
Housing RTA - 50
902302
902329
902304
902305
502296
505008
902309
502243
902314
902315
902316
902317
902318
902319
4
Pressure Plate Plug 1/2‖ - 14 NPT
Sq. Hd. Plug 1/4‖ - 18 NPT
Bolt M-10-25 (Pkg. 6)
Bolt M-10-30 (Pkg. 4)
Spacer
5
6
7
8
9
Shim Pack (Pkg. 8)
10
10
11
11
12
13
Output Gasket 0.8mm
Output Gasket 0.5mm
Input Gasket 0.4mm
Input Gasket 0.2mm
Output Seal Double Lip
Input Seal Double Lip
14
15
16
17
18
18
18
Sealed Ball Bearing (6308)
Ball Bearing (6308)
902320
902321
902322
902323
902324
902330
902331
Ball Bearing (6307)
Ball Bearing (6207)
Output Shaft TG-48 500mm
Output Shaft TG-60 700mm
Output Shaft TG-72 900mm
19
20
Pinion Shaft 13 Teeth
Output Gear 19 Teeth
902325
902326
21
22
Cap Blank
902327
902328
Cap Hub TG-48 500mm
22
22
Cap Hub TG-60 700mm
Cap Hub TG-72 900mm
902332
902333
35
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Limited Warranty.
King Kutter, Inc. (―King Kutter‖), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail pur-
chaser (―Purchaser‖) that the product that is the subject of this sale is free from defects in material and work-
manship at the time of sale.
Under this warranty, King Kutter will repair the defective product free of charge to the Purchaser, with either
new or used and reconditioned replacement parts. All warranty service will be performed at service centers
designated by King Kutter. If King Kutter is unable to repair the product to conform to the warranty after a
reasonable number of attempts, King Kutter will provide, at its option, one of the following: (a) a replacement
for the product or, (b) a full refund of the purchase price. Repair, replacement, or refunds are the Pur-
chaser’s EXCLUSIVE remedies against King Kutter under this limited warranty. King Kutter will not be liable
for any special, incidental or consequential damages based upon breach or warranty, breach of contract, neg-
ligence, strict tort liability, or any other legal theory. Such damages include, but are not limited to, loss of prof-
its, loss of savings or revenue, loss of use of the product or any associated equipment, cost of capital, cost of
any substitute equipment, facilities or services, down time, the claims of third parties including customers, and
injury to property. These limitations also apply, to the extent allowed by law, to personal injury.
The purchaser must notify the Seller in writing of any defect in material or workmanship within one (1) year
following the date of purchase. If the equipment is used for commercial purposes, the Purchaser must notify
the Seller in writing of any defect in material or workmanship within ninety (90) days following the date of pur-
chase. In no event will King Kutter be liable under this warranty unless written notice is received by the Seller
within one (1) year from the date of original retail sale.
2. Warranty of Title.
King Kutter warrants that it transfers a good title to the product free of any encumbrances, and free of the
rightful claim of any third party for infringement of patent or copyright.
3. What is Not Covered by This Limited Warranty.
King Kutter will not be responsible for damage to or failure in the product which results from accident, misuse,
abuse, neglect, installation of attachments not provided by King Kutter, modifications to the product, or dam-
age caused by use of the product for purposes other than those for which it was designed.
4. No Other Warranties.
Unless modified in writing and signed by both parties, this agreement is understood to be the complete and
exclusive agreement and warranty between King Kutter and Purchaser, superseding all prior agreements,
oral and written, and all other communication between King Kutter and Purchaser related to the subject mat-
ter of this agreement.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-
ING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee of King Kutter nor anyone else is
authorized to make any warranty or representation in addition to or different from those made in this agree-
ment.
5. Allocation of Risk.
This agreement allocates the risk of product failure between King Kutter and the Purchaser. This Allocation is
recognized by both parties as reflected in the price of the goods. The Purchaser acknowledges that he or she
has read this agreement, understands it, and is bound by its terms.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|