MX
MULTI-CHANNELMARINE
AMPLIFIER
with a CLASS-DSUBWOOFERCHANNEL
MX700.5
©2007 Stillwater Designs
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ LED Red, no output? 1) Amplifier is very hot. ꢁThermal protection is engaged. Test for proper impedance at the
speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and
multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down
only while vehicle is running. ꢁVoltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16
volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low
volume levels. ꢁShort circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
Operation
Your Kicker MX.5 series amplifier has seven rotary controls and two switches on the top panel. Before turning on the
system for the first time, remove the sealed top panel (protects the controls from water damage) by removing the two
phillips screws. See Figure 1. Then turn the seven rotary controls on the top of the amplifier to the full counter-
clockwise position.
1. CrossoverSwitch The crossover switches on the top panel are for setting the internal crossovers for the
“full-range” audio channels (12dB slope per octave). In the OFF position the amplifier passes a full-range signal to the
speakers. The HI position should be selected when connected to speakers, which you do not want to receive any
sub-bass information. Never change the crossover "OFF/HI" switch setting with the audio system on!
ꢀ No output from one channel? 1) Check the balance control on source unit 2) Check the RCA and speaker
output connections for the channel 3) Swap the RCA cable from left to right. If the problem changes sides then you
have a bad RCA cable or source unit problem. 4) Swap the speaker output wire from left to right. If the problem
changes sides then you have a bad speaker cable, passive crossover network and/or speaker.
2. InputGainControl The input gain control is not a volume control. It matches the output of the source unit to the
input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it to 25).
Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it down a little.
ꢀ Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable
2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the
gain settings and turn them down if they are set too high.
Adjust AMP 1, then proceed to AMP 2 and finally the Subwoofer Channel input gain control.
ꢀ Poor stereo image or reduced bass response? ꢁCheck system phasing by turning the balance control from left
to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover
networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from
positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.
3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB at 40 Hz. The
setting for this control is subjective. If you turn it up, you must go back and adjust the input gain control to avoid
clipping the amplifier.
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.
ꢀ Ground-Loop Noise? ꢁIf you are using only one pair of RCA inputs, connect the RCA cable to the AMP 1 inputs.
ꢀ No Fader? ꢁYou must use both sets of RCA Inputs for AMP 1 and 2, in order for the source’s fader to work.
5. RemoteBass(Level Control) When using the remote bass level control you have the ability to control the level of
the Subwoofer Channel’s output remotely. To mount the remote bass level control, simply screw the metal bracket to
the chosen location. Then slide the housing onto the bracket until it snaps into place. Run the cable from the controller
to the “Remote Bass” jack on the amplifier chassis.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you
made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the
TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information.
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can
result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
Two Kicker Coax Speakers wired
in series to a single channel.
Performance
-
+
Model
MX700.5
RMS Power in Watts, AMP 1 and AMP 2 channels driven
@14.4V, 4Ω Stereo ≤1% THD+N
@14.4V, 2Ω Stereo, ≤1% THD+N
@14.4V, 4Ω Mono, ≤1% THD+N
RMS Power in Watts, Subwoofer Channel driven
@14.4V, 4Ω Mono, ≤1% THD+N
@14.4V, 2Ω Mono, ≤1% THD+N
Length:
70 x 4
85 x 4
165 x 2
-
+
Figure 4
210 x 1
420 x 1
Wiring two Kicker Speakers to a single channel
20” (507mm)
Height:
2 3/8” (60mm)
Modern high performance coaxial and component speakers have a lower DC Resistance than what used to be
available. The Kicker speakers are rated at four ohms and work with any source unit or amplifier designed to operate
at a four ohm load. If you want to use two Kicker coax or component speakers on each channel of your amplifier wire
the speakers in series, as shown in Figure 4. This will improve the sound quality, lower the total harmonic distortion
and lessen the thermal load at the source unit or amplifier. This may prevent an amplifier from shutting down, due to
over-current protection circuitry.
Width:
10” (254mm)
Frequency Response, 0.5 dB:
Signal-to-Noise Ratio:
20 Hz - 20 kHz
>95 dB, a-weighted, re: rated power
125 mV - 5 V
Input Sensitivity:
Electronic Crossover:
Variable (defeatable) HI pass, 50 - 200Hz, 12dB per octave, for the full-range channels
Variable LOW pass, 50 - 200Hz, 24dB per octave, for the subwoofer channel
Variable 0 to +18 dB boost @ 40 Hz, for the subwoofer channel
TroubleShooting
Bass Boost:
If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or incorrect
wiring connections, incorrect setting of crossover switch and gain controls, etc. There is one LED on the top of your
Kicker MX series amplifier. When the LED is green this indicates the amplifier is turned on and no trouble exists. If the
LED is red, this indicates that the protection circuitry (SORT) is engaged.
Model MX700.5
70 x 4, 210 x 1 @ 4 ohms from 20-20K, 20-200Hz, 14.4Vdc,
1% THD, CEA-2006 (Watts)
ꢀ LED Green, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal (should
read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power and
ground connections 4) Ground terminal, for proper conductivity.
Signal to Noise Ratio -72 / -55 dBa CEA-2006 (ref: 1W, A-weighted)
ꢀ LED Green, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known” good
speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable feeding
the amplifier with the “AC” test position selected on the VOM meter.
All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Download from Www.Somanuals.com. All Manuals Search And Download.
MX.5AMPLIFIER
4
5
ElectronicsLimitedWarranty
InternationalWarranty
Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer
it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original
receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction
during the warranty period, Kicker will repair or replace (at its discretion) the defective merchandise with equivalent
merchandise at no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued
products may be replaced with more current equivalent products.
Contact your International Kicker dealer or distributor concerning specific procedures for your country's warranty
policies.
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing!
Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an
undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too
loud and may permanently damage your hearing. Please use common sense when controlling volume.
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the
original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as
provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or
implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore
these exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other
rights that vary from state to state.
GARANTÍA INTERNACIONAL
VersiónEspañol
Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos
específicos relacionados con las normas de garantía de su país.
ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar
permanentemente el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el
oído que escuchar un sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es
muy fuerte y que puede dañar permanentemente el oído. Sea precavido cuando controle el volumen.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise should be returned to your local Authorized Stillwater Designs (Kicker) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater
Designs directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window
decal.
La frase "combustible para vivir la vida Livin' Loud™ a todo volumen" se refiere al entusiasmo por la vida que la marca
Kicker de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible ("a
todo volumen") en todo sentido. La línea de altavoces y amplificadores Kicker es la mejor del mercado de audio de
automóviles y por lo tanto representa el "combustible" para vivir a todo volumen en el área de "estéreos de automóvil"
de la vida de nuestros clientes. Recomendamos a todos nuestros clientes que obedezcan todas las reglas y
reglamentos locales sobre ruido en cuanto a los niveles legales y apropiados de audición fuera del vehículo.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (Kicker), call the Kicker
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package all
defective items in the original container or in a package that will prevent shipping damage, and return to:
INTERNATIONALE GARANTIE
DeutscheVersion
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die
Garantieleistungen in Ihrem Land zu erfahren.
The RMA number must be clearly marked on the outside of the package. Please return only defective components.
The return of functioning items increases your return freight charges. Non-defective items will be returned freight-
collect to you.
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass
der Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung
bitte vernünftig!
Include a copy of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing
the Customer's name, Dealer's name and invoice number, and product purchased. Warranty expiration on items
without proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be
prepaid; items sent freight-collect, or COD, will be refused.
Der Slogan "Treibstoff für Livin' Loud" bezieht sich auf die mit den Kicker-Autostereosystemen assoziierte
Lebensfreude und die Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten
("Livin' Loud") zu streben. Die Lautsprecher und Verstärker von Kicker sind auf dem Markt für Auto-Soundsysteme
führend und stellen somit den "Treibstoff" für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren
Kunden, sich bezüglich der zugelassenen und passenden Lautstärkepegel außerhalb des Autos an die örtlichen
Lärmvorschriften zu halten.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products returned without a Return Merchandise Authorization (RMA) number
o Freight Damage
GARANTIE INTERNATIONALE
VersionFrançaise
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou
distributeur International Kicker.
AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager
l'ouïe de façon irréversible ! L'augmentation du volume d'un système jusqu'à un niveau présentant une distorsion
audible endommage davantage l'ouïe que l'écoute d'un système sans distorsion au même volume. Le seuil de la
douleur est toujours le signe que le niveau sonore est trop élevé et risque d'endommager l'ouïe de façon irréversible.
Réglez le volume en faisant prevue de bon sens !
o The cost of shipping product to Kicker
o Service performed by anyone other than Kicker
L'expression " carburant pour vivre plein pot " fait référence au dynamisme de la marque Kicker d'équipements audio
pour véhicules et a pour but d'encourager nos clients à faire le maximum (" vivre plein pot ") dans tous les aspects de
leur vie. Les haut-parleurs et amplificateurs Kicker sont les meilleurs dans le domaine des équipements audio et
représentent donc pour nos client le " carburant pour vivre plein pot " dans l'aspect " installation audio de véhicule "
de leur vie. Nous encourageons tous nos clients à respecter toutes les lois et réglementations locales relatives aux
niveaux sonores acceptables à l'extérieur des véhicules.
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 72-hour service for all electronics (amplifiers, crossovers, equalizers, etc.) returns.
Delays may be incurred if lack of replacement inventory or parts is encountered.
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service
Department at (405) 624-8510.
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510
01252007+07MX.5
Download from Www.Somanuals.com. All Manuals Search And Download.
MX.5AMPLIFIER
4
5
|