Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Titanium Deposit Impregnated Cone An Ultra High
Performance look that is more rigid for less cone flex and less
distortion.
ARCTIC Cap (Aluminum Rapid Cooling Thermal Induction
Centering Cap) Mounted on top of the extended pole--piece
it is responsible for insuring the voice coil on the SPAIR is
properly centered when inserted into the BAM, adds more
mass for increased thermal transfer from the voice coil to the
pole piece and channels air into the “X” Vent for increased
cooling.
Advanced Cone Technology The outer edge of the cone has
been rolled to increase cone rigidity to decrease cone flex
under high excursion.
SPAIR (Simple Pull Apart Insertable Replacement) A
stamped steel removable cone assembly. (Patent Pending)
S4 Quad Spider Array 4 Poly nomex spiders keeps the voice
coil properly centered under high excursion.
Uniplate V.2 with Vented Hyper-Extended Pole
(Patent Pending)
Triple Stack Custom Tooled Magnets With a BAM this big, a
double just wouldn’t fill your appetite.
1. Utilizes “X” Vent technology to insure proper dissipation
of heat away from the voice coil during operation.
2. Provides enhanced heat transfer for cool operation and
maximum power handling.
ISD (Inverted Structural Dome) Further increases cone’s
resistance to flex under pressure.
3. Increases the linear magnetic fields around the voice coil
gap for superior cone motion control.
Stitched Surround Prevents cone/surround separation at high
excursions.
4. Releases pressure under ISD for freer cone motion and
enhanced low bass.
Dual Ultra-Length Voice Coils For high excursion and flexible
wiring options.
SLAM (SPAIR Lockdown Attachment Mechanism) The alu-
minum frame attached to the SPAIR which properly secures
the removable speaker assembly (SPAIR) to the BAM (Basket
And Motor assembly).
Oversized 3.5” Voice Coil With bottom rolled out for
increased retention capabilities.
Strain Relief Boots for Tinsel Lead Wires Large heavy gauge
tinsel lead wire with strain relief boots.
SPLAT (Speaker Precise Location Alignment Tool) Locates
and anchors the BAM to the baffle of your enclosure.
B3-Link 3-Way Connection System which allows you to use
Binding post, terminal Block, or Barrier strip for connecting
the speaker wires.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
2
Wiring
The terminals with red and black wings are for one voice coil. The
terminals with the silver colored wings are for the second voice coil.
Due to the nature of this subwoofer care must be taken when con-
necting the wires to the proper terminals!
The SoloX woofers are available with dual 2 Ohm or dual 1 Ohm
voice coils. Both coils should always be hooked up.
The dual 2 Ohm woofer will give you a 1 Ohm or a 4 Ohm load
depending on if the coils are wired in parallel or in series. The dual 1
Ohm woofer will give a .5 Ohm or 2 Ohm load depending on how they
are wired.
Parallel
Series
Coil 1 +
Coil 1 +
Ω #
Ω #
C O I L 1
C O I L 1
Amplifer +
Speaker Connection
Amplifer +
Speaker Connection
Coil 1 -
Coil 2 -
Coil 1 -
Coil 2 -
Amplifer
Speaker Connection
Amplifer
Speaker Connection
COIL 2
#Ω
COIL 2
#Ω
Coil 2 +
Coil 2 +
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
3
Enclosures
The SoloX is one of the most advanced subwoofers on the market,
therefore, care must be taken when designing an enclosure. We will
provide you with enough information for you to properly construct
an enclosure. If you feel you are not capable of building it yourself,
we highly recommend letting one of our Authorized Dealers build it
for you. It will save you a lot of heartaches and headaches. The SoloX
subwoofer is capable of handling unheard of power. A simple enclo-
sure will not be enough. The enclosure will need to be made of a min-
imum of 1” MDF and properly braced. You may use 4” x 4” (10.16cm x
10.16cm) triangular braces between each of the larger unsupported
panels or a center brace (as seen on the next page). We also recom-
mend using a good grade wood glue and silicone rubber to insure an
airtight seal.
The wood support inside your SoloX shipping carton can be used as
a template for cutting the speaker mounting hole in the enclosure.
Since the wood cut out is the same size as the basket of the SoloX,
when you make the cut along the line drawn through the template,
make sure to cut right on the line to get the correct opening size.
All the cubic feet numbers given in the following pages include the
displacement of the woofer. For the ported boxes the displacement
of the port must be added to the final design. It will be impractical to
use round ports for these designs. The rectangular port information
given will yield the best results. Keep in mind the pressure inside of a
ported enclosure exceeds that of a sealed enclosure
Note: If you prefer an ultra-smooth bass response, you should
loosely fill your SoloX Enclosure with polyfil. Ported designs will
require covering the entrance to the port (inside the box) with hard-
ware cloth, chicken wire, or expanded metal to prevent the polyfil
from being blown out through the port. Use of polyfil will slightly
decrease efficiency, but will deepen and extend low bass response.
Do not install a ported box with the port against a solid surface. The
port opening must remain unobstructed. Use the smallest dimension
of the rectangular port as the minimum amount of space required
between the port and any surface to insure unrestricted airflow.
For more advice on box building, see the Choosing and Building
Enclosures page in the Tech Tips & FAQs section of the Support area
405-624-8583.
A note on power handling capability
SoloX subwoofers will handle massive amounts of power in any of
the recommended enclosures. The power ratings given are assuming
that both voice coils are used. You should never hook up a dual voice
coil woofer using only one coil.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
4
Sealed Design
SoloX Series Sealed Enclosure Applications
The SoloX is designed for Vented enclosure/ High SPL applications
and that is where maximum output and power handling will be
achieved. If you are willing to give up maximum SPL and power han-
dling for more low bass output, then you can utilize our sealed enclo-
sure recommendations.These sealed enclosure recommendations will
give the smoothest response with the most energy at really low fre-
quencies, around 20 to 30 Hz.
The recommended Tuner sealed box will deliver massive amounts
of high impact bass and can be driven with punishing levels of ampli-
fier power.
One of the benefits of the SoloX series high performance suspen-
sion system is that they can operate in larger sealed enclosures for
ultra low bass performance (SUV applications) while still maintaining
excellent control and power handling.
SoloX series woofers also perform well in any sealed enclosure
between the Tuner and SUV sizes. These systems will exhibit some
benefits of both (high impact and low extension) generally sounding
more like the box to which they are most closely sized.
These enclosure volume recommendations are for the airspace
inside the enclosure and include the displacement of the woofer. Do
not make the airspace any greater than recommended.
S18X
Recommended Enclosures
Model
Tuner:
6 cu.ft., Fb= 51.3Hz
F3= 24.6Hz, Pmax= 2800W
SUV:
12 cu.ft., Fb= 48.8Hz
F3= 22.2Hz, Pmax= 2400W
or call our Technical service line at 1-405-624-8583.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
5
Vented Design
S18X
SoloX Series Vented Enclosure Applications
The Kicker SoloX is truly awesome in a vented enclosure as this is
what it was designed for. Throw out every experience you have ever
had with a vented speaker and prepare to be blown away! Our engi-
neers have designed several boxes that will truly irritate everyone
within a 3 mile radius.
Because a woofer of this magnitude has never been produced, even
we do not know the total capabilities of the SoloX. The following chart
shows three recommended vented enclosures for the SoloX: Tuner,
SUV, and SPL. Keep in mind, these enclosure volume recommenda-
tions are for the airspace inside the enclosure and include the dis-
placement of the woofer. Do not make the airspace any greater than
recommended. These enclosures are just scratching the abilities of
this woofer to blow away all other woofers on the market. So keep
your eye on the website for the newest sick enclosures!
Recommended Enclosures
Tuner :
SUV:
5 cu.ft. Port: 60sq.in. x 14.5”
Fb= 35Hz, Pmax= 5000W
( with 25hZ subsonic filter)
10 cu.ft. Port: 150 sq.in. x 21”
Fb= 35Hz, Pmax=4500W
( with 25hZ subsonic filter)
SPL:
10 cu.ft. Port: 300sq.in. x 9”
Fb= 56Hz, Pmax= 10000
(Above tuning freq. only)
See below!
This enclosure is intended for SPL ONLY! It is designed
to be used with test tones above 56Hz! Playing music
with frequencies below 56Hz will result in very, very bad
things happening!!
For more advice on box building, see the Choosing and Building
Enclosures page in the Tech Tips & FAQs section of the Support area
405-624-8583.
ATTENTION!
The hardware we include will work with baffles up to 1.5”
thick. For thicker baffles you will need to use longer 1/4” x 20
hardware.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
6
Mounting
Now that you have opened the box and read “The
Adventures of Sam Stikman” and decided on which enclosure
design to use, you may now remove the SoloX from it’s box.
Please follow the instructions
4. With the Gap Cap now
installed remove the (4) double
end threaded studs that lock the
BAM to the wood baffle assem-
bly.
lined out here to insure proper
installation.
1. With assistance from a
friend remove the SoloX from
the cardboard facilitation cham-
ber.
The SPLAT and wood baffle will
now come free from the BAM.
The baffle will now become your
mounting template.
2. Once out of the carton remove
the (4) four acorn head nuts and
(8) eight bolts securing the SPAIR
to the BAM and wood baffle
assembly. Place SPAIR in safe
clean location!
ATTENTION!
3. Install the Gap Cap into the
BAM around the pole-piece to
protect the motor assembly
from debris while you are
installing the woofer. If any
metal shavings were to fall into
the gap, they would be impossi-
ble to remove! Please use the
Gap Cap!
5. Place the wood template on
your enclosure baffle to mark
the holes for mounting.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
7
9. With your assistant,
insert the BAM and start
the corner hardware.
Now is the time you
remove the unidirec-
tional bonding strip!
(Tape) Tighten the dou-
ble threaded studs to
secure the BAM to the
baffle.
6. Once the holes are marked
remove template. Using a jigsaw
cutout the woofer hole and use
a 3/8” drillbit for the mounting
holes
WARNING!
You will need assistance for the
following steps!
Baffle
10. Pull the wires out through
the BAM and connect to the B3
Link of your choice. Make sure
you are using proper polarity!
7. Insert the SPLAT into the
cutout and move into position.
8. Use masking tape to
temporarily hold the SPLAT
in place while securing the
BAM. This tape can be
removed after the corner
hardware has been start-
ed.
11. Remove the Gap Cap before
inserting SPAIR.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
8
14. Pop open a cold beverage and admire your work!
12. Insert the SPAIR back into
the BAM. Be careful not to dam-
age the voice coil. The double
threaded studs and the ARCTIC
Cap will help to center SPAIR as
you lower it into the BAM.
When properly aligned these
assemblies slide together easily.
13. Using the 1/4”-20 acorn head
nuts and eight bolts secure the
SPAIR to the BAM. When tight-
ening the nuts follow the pat-
tern drawn below. This will
insure a proper fit.
ATTENTION!
Follow the pattern, hand tight-
ening each, then go back and
tighten using the same pat-
tern.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
9
Specifications
Model:
S18X1
S18X2
Nominal Impedance
(Impedance per coil)
SPL 1W/1M
Displacement, cc
Displacement, CuIn
Mounting Depth
Revc
1
2
90.27
3930
89.7
3930
239.8
11-3/8
2.05
239.8
11-3/8
4.07
VC Inductance, mH
Sd, SqM
3.247
0.1426
31.45
185.64
6.55
4.289
0.1426
40.36
177.61
6.27
BL
Vas, Liters
Vas, CuFt
Mms, gms
859.8
21.4
836.5
22.18
7.83
Fs
Qms
8.838
0.240
0.233
10000
5000
Qes
0.291
0.281
10000
5000
Qts
Pmax, Peak watts
RMS watts
EXmax, mm
(Excursion maximum)
24.48
24.48
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
10
Warranty expiration on items without proof-of-purchase will be determined from the manufacturing date code. Freight
must be prepaid; items received freight collect will be refused. Failure to follow these steps may void your warranty.
Any questions can be directed to the KICKER Customer Service Department at (405)624-8510
This warranty is valid only if the product is used for the purpose for which it was designed.
SoloX Limited Warranty
KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase. When purchased from an Authorized KICKER Dealer this
product is warranted for ONE (1) YEAR from date of purchase. If the product is labeled “B Stock” it is warranted for
THREE (3) MONTHS from date of purchase. Should service be necessary under this warranty for any reason due to
manufacturing defect or workmanship during the warranty period, KICKER will replace or repair (at its discretion) the
defective merchandise with equivalent merchandise at no charge. Warranty replacements on “B Stock” merchandise
may have cosmetic scratches and blemishes. Discontinued products may be replaced with more current equivelant
products.
Caution: Burnt voice coils are
not covered under warranty
* Speaker with any foreign caulk used for gasket
material.
* Items previously repaired or modified by any
unauthorized repair facility.
* Return shipping on non-defective items.
* Products with tampered or missing barcode labels.
* Products returned without a Return Merchandise
Authorization (RMA) number.
In addition, the warranty does not cover:
* Damage due to improper installation.
* Subsequent damage to other components.
* Damage caused by exposure to moisture, excessive
heat, chemical cleaners, and/or UV radiation.
* Damage through negligence, misuse, accident or
abuse.
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the
original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as pro-
vided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied,
shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclu-
sions may not apply to you.
* Any cost or expense related to the removal or
reinstallation of the product.
* Freight damage.
* The cost of shipping the product to Kicker.
* Service performed by anyone other than Kicker.
* Speakers damaged due to amplifier clipping or
distortion.
How long will it take
This warranty gives you specific legal rights; however you may have other rights that vary from state to state.
Stillwater Designs (KICKER) maintains a goal of 24-hour service for all returns. Delays may be incurred if lack of
replacement inventory or parts is encountered.
Should you need Service
International Warranty
Defective merchandise must be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty.
Assistance in locating an Authorized Dealer can be obtained by writing or calling Stillwater Designs (KICKER) direct.
You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
Contact your International Stillwater Designs (KICKER) dealer or distributor concerning specific procedures for your
country’s warranty policies.
If it becomes necessary for you to return defective merchandise, call the KICKER Customer Service Department at
(405)624-8510 for a Return Merchandise Authorization (RMA) number. Package all defective items in the original con-
tainer or in a package that will prevent shipping damage, and return to
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • 405 624-8510
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Return only defective components. Return of
the entire cabinets, system packs, pairs, etc. increases your return freight charges. Non-defective items received will
be returned freight collect. Include a dated proof-of-purchase stating the Customer name, Dealer name, product pur-
chased and date of purchase.
KICKER drivers are capable of producing sound levels that can permanently dam-
age your
hearing! Turning up a system to a level that has audible distortion is more damag-
ing to your ears than listening to an undistorted system at the same volume level.
The threshold of pain is always an indicator that the sound level is too loud and
WARNING:
may permanently damage your hearing.
Please use common sense when controlling volume!
February 2003
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
SoloX Limited Warranty
Ok, you have read all the fine print on the previous page describing the warran-
ty on a Solo X Subwoofer, (enough there to make even Judge Judy happy) but
what does it all mean? Well, let's just lay it all out in as simple of terms as possi-
ble.
We also do not warranty the SPAIR for:
¾
¾
¾
¾
Wear and Tear under normal use.
Product damaged due to abuse.
Damage to Vehicle and/or other components of the sound system.
Scattered, Smothered, Covered and Chunked units.
The Solo X is a high performance machine that is built to take gobs of power,
play extremely loud and create enough low bass to rattle the fillings out of your
friend's teeth who lives in the next county. It is built using the finest materials
and highest degree of workmanship we have available. It is the NASCAR of sub-
woofers…designed to be driven hard into all four corners…and we are sure you
will drive it just that way!
The SPAIR and BAM are not covered under warranty for any damage due to
shipping or improper packaging.
So what will KICKER cover under warranty?
¾
¾
¾
Poor or misaligned glue joints.
Poor or misaligned parts.
Material, Machining or Assembly flaws with the BAM.
With all that being said…we know some of you will still be able to break this
product…it is a plain and simple fact. When you build an extreme product to be
used by extreme people these people can and will find the breaking point…just
like Tony Stewart snapping a rod in a motor.
So in a nut-shell if and when you break it (which takes A LOT) you simply return
the soft parts assembly (the SPAIR) to your local dealer and purchase another
SPAIR. If there is a problem with the SPAIR and you feel it should be covered
under warranty, you will need to obtain an RMA from KICKER before sending it
back. If only the SPAIR is defective, there is no need to send the entire structure
back to KICKER. Refer to SHOULD YOU NEED SERVICE on the previous page
for the details.
That is why we designed the Solo X to have a permanently mounted BAM
(Basket And Motor) assembly with a replaceable soft parts assembly, the SPAIR
(Simple Pull Apart Insertable Replacement), so that when you find the breaking
point (and if you can still hear or feel) you can re-build it on the spot. If you
read the big poster that came with your woofer (you did…right?) you know
Sam & Sid told you this thing weighs more than a Mini Cooper (well…really it
weighs in at near 100 pounds). The BAM which is about 90% of the weight in a
Solo X stays mounted in your enclosure AND in your car; you simply exchange
the much lighter SPAIR. This saves you all the fun of wrestling with the entire
Solo X and the ENORMOUS costs of shipping a 100 pound woofer to Stillwater,
Oklahoma.
Special Note: OK that all sounds pretty black and white but we are KICKER and
we know stuff happens. If your Solo X stops working and after pulling the SPAIR
you find a failure other than that mentioned above that you feel is a manufac-
turing defect or poor workmanship you may call Stillwater Designs (KICKER) for
a RMA (Return Merchandise Authorization). You will then have to wrestle the big
unit, meaning the Solo X Subwoofer, (BAM and SPAIR both) and pack them in
the original shipping container that you got at the time of purchase. You MUST
use the original packing to protect the unit during shipping!!! You will be
responsible for the freight charges.
The SPAIR and all the parts contained within it are not warranted for:
¾
¾
¾
¾
¾
Burnt, Shucked, Bent, Unraveled or Open Voice Coils.
Torn, Ripped or Punctured Surrounds.
Torn, Ripped or Punctured Cones.
Torn, Ripped or Punctured Spiders.
Burnt or Frayed Tinsel Leads.
After receiving your Solo X and examining it, one of three things will happen.
¾
¾
¾
If a problem is found that is indeed covered under warranty, we will
repair the unit and return it to you at no additional charge.
If no problem is found we will return the unit to you and you will be
responsible for the freight charge.
If a problem is found that is not covered under the warranty as
described in the warranty statements, you will be charged for the
cost of the repair and freight charge to return the unit to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
SoloX Subwoofer
Download from Www.Somanuals.com. All Manuals Search And Download.
|