TREADMILL
MS1200GT/MS3200GT
OWNER’S MANUAL
KEYS Fitness Products, LP
P.O. Box 551239
Dallas, Texas 75239
PART# 15-0008
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification Sheet
MS1200GT
2.0hp
MS3200GT
2.0hp
♦ Horsepower (Continuous)
♦ Display Type
5Window LCD 5Window LED
♦ Electronics
Push button
3
Push button
5
♦ Pre-Set Programs
♦ Custom Programs
♦ User Programs
♦ Heart Rate Interactive
♦ Power Incline
6
10
0
3
No
Yes
12%
12%
♦ Roller Diameter
♦ Cushioned Deck
♦ Speed Range
1.9”
1.9”
Yes
Yes
0-10mph
18 x 51”
Yes
0-10mph
18 x 51”
Yes
♦ Belt Size
♦ Front Hand Rails
♦ Side Hand Rails
♦ Foot Print
Yes
Yes
29 x 62”
29 x 29”
10Years
2Years
1Year
Lifetime
26 x 62”
29 x 29”
10Years
2Years
1Year
Lifetime
♦ Foot Print Folded
♦ Warranty Motor
♦ Warranty Parts
♦ Warranty Labor
♦ Warranty Frame
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
1) WARNING! Before using this treadmill or starting any exercise program, consult your physician. This is especially
important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor
assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
2) WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is
important to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
♦ It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar
with warnings and safety precautions.
♦ This treadmill has a user maximum capacity of 275 pounds.
♦ The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be
placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill
mat be placed under the treadmill to protect floor or carpet and for easier cleaning.
♦ Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline
wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or
frayed power cord.
♦ Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with
bare feet, sandals, socks or stockings.
♦ Always straddle the belt and allow it to start moving before stepping onto the belt.
♦ Hold on to handrails when adjusting speed, incline, or other controls.
♦ Always examine your treadmill before using to ensure all parts are in working order.
♦ Allow the belt to fully stop before dismounting.
♦ Pets should never be allowed near or on the treadmill.
♦ Do not leave children unsupervised near or on the treadmill.
♦ Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
♦ Never insert any object or body parts into any opening.
♦ For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
♦ Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow
these instructions will void the treadmill warranty.
♦ Never leave the treadmill unattended while it is running.
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
BeforeYou Start
Thank you for purchasing a KEYS treadmill! This quality product you have chosen was designed to meet
your needs for cardiovascular exercise.
Before you start, please read the Owner’s Manual and become familiar with the operation of your new
treadmill.
♦ Remember to take the time to perform the stretching exercises provided on Page 6 to avoid injury.
♦ Do not stand on the walking belt while pressing the Power button or Start/Stop button.
♦ Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds.
♦ If you are taking medication, consult your physician to see if the medication will affect your exercise
heart rate.
♦ If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-
set treadmill programs or start an exercise program without first contacting and receiving approval
from your physician.
♦ To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console.
KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.
♦ Please review the following picture below to familiarize yourself with the listed parts. This manual
covers several treadmills, so the one pictured below may not be identical to your particular model.
CONSOLE
ELECTRONIC DISPLAY
WATER BOTTLE HOLDER
(WATER BOTTLE NOT INCLUDED)
SIDE HAND RAILS
SAFETY LATCH
FRONT HAND RAIL
UPRIGHTS
MOTOR COVER
WALKING BELT
CIRCUIT BREAKER
REAR ROLLER
ADJUSTMENT BOLTS
SES SYSTEM
WHEEL
FOOT RAILS
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
EXERCISE GUIDELINES
WARNING! Before beginning this or any exercise program, you should consult your physician. This is especially im-
portant for individuals over the age of 35 or individuals with pre-existing health problems.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and
raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The
photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve
an adequate warm-up, perform each stretch three times.
TOE TOUCH STRETCH
Stand bending your knees slightly and slowly bend for-
ward from your hips. Allow your back and shoulders to
relax as you reach down toward your toes as far as possi-
ble. Hold for 15 counts, then relax. This will stretch
your hamstrings, back of knees , and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite
foot toward you and rest it against the inner thigh of your
extended leg. Reach toward your toes as far as possible.
Hold for 15 counts, then relax. This will stretch your
hamstrings, lower back, and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and
place your hands against a wall. Keep your back leg
straight and your back foot flat on the floor. Bend your
front leg, lean forward and move your hips toward the
wall. Hold for 15 counts, then relax. To cause further
stretching of the Achilles tendons, bend your back leg as
well. This will stretch your calves, Achilles tendons, and
ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as
close to your buttocks as possible. Hold for 15 counts,
then relax. This will stretch your quadriceps and hip
muscles.
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly, Moving Instructions
Assembly
This KEYS treadmill is shipped in one piece and fully assembled. After opening the box, remove any packing materials
from the treadmill. Do not throw away any packing materials until the unit is working properly. Place the base on a
clean, level surface. Make sure the electrical cord will easily reach an electrical outlet.
Moving
CAUTION! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREADMILL
WHILE IT IS IN THE UNFOLDED OPERATING POSITON. TO REDUCE THE POSSIBILITY OF
INJURY WHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT. AS YOU RAISE
THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. IN ORDER TO RAISE OR LOWER
THE TREADMILL SAFELY, YOU MUST BE ABLE TO LIFT 45 POUNDS (20KG). IT IS SUGGESTED
YOU ALWAYS USE THE AID OF A SECOND PERSON WHEN MOVING THE TREADMILL.
With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails and place one foot on the
base as shown in the photo below. Next, with a firm grasp on handrails, place one foot on the center of the base
crossbar and carefully tilt the treadmill back until it rolls freely on the wheels. Using extreme caution, move the
treadmill to the desired location. To set the treadmill down, place one foot on the center of the base crossbar and
carefully lower treadmill onto base in resting position. Do not attempt to move the treadmill over an uneven or rough
surface.
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
ARNG!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A
RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF
YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT
MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET, HAVE
A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes,
surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To
reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge
protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage
rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance
for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug
the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in
the drawing below.
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
There are five display windows on the control panel to provide feedback information.
TIME WINDOW
♦ TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)
♦ INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds
SPEED WINDOW
♦ SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
♦ DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0
♦ CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time
INCLINE WINDOW
♦ INCLINE: Indicates incline in percent of grade 0-12% in 1 increments
CENTER BRICKYARD WINDOW
♦ Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the change
in speed profile across the interval range (1-10) and shows position with a blinking action.
♦ In Program mode, the treadmill will display the name of the program selected, showing on the left hand side of the
window. In Manual mode, the LAP counter will appear in the top center of the window, counting each 1/4 mile lap in
sequence of completion (1, 2, 3, etc.)
CENTER BRICKYARD WINDOW
TIME WINDOW
DISTANCE/CALORIE WINDOW
INCLINE WINDOW
SPEED WINDOW
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
♦ QUICK START / MANUAL MODE
♦ Plug into a surge protector outlet. Attach RED Safety Key to treadmill console.
♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
♦ Press POWER button. There will be an eight (8) second delay after pressing the POWER button before
data can be entered. The TIME window will flash.
♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt
starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease)
buttons.
♦ To end your workout, press START/STOP button. Belt will gradually slow to zero.
♦ To pause your workout, press PAUSE.
♦ To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL
RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING.
♦ Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting
started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or –
arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME
window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press
ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to
set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.
POWER
START/STOP
PAUSE
ENTER
INCLINE
SPEED/TIME
Alternative Speed and Incline Toggles Switches
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE-FORTHE MS1200GT
♦ Plug treadmill into a surge protector outlet . Attach RED Safety Key to treadmill console.
♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
♦ Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window
will flash.
♦ There are three (3) pre-set and six (6) custom pre-set programs on the MS1200GT. The treadmill includes FAT
BURN, CARDIO, and WARM-UP programs. Select the program by pressing the appropriate button.
♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving.
♦ Each of the pre-set programs can also be customized for your particular workout.
♦ CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-up) can be
customized in the P1 or P2 mode. After making the program selection, the center window will read “OP.” The
”OP” refers to “original program” and is preset. The program name you select will display to the left of the
“OP”. Press the same program button once more and the center window will read P1. The “P1” mode is now
accessed. You can now program the Time, Speed, and Incline in P1 mode, which will be saved for future work-
outs.
1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press
ENTER PROGRAM.
2) The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your
workout. Press ENTER PROGRAM.
3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press
ENTER PROGRAM.
To start, press the START/STOP button. To access P2 mode, press the selected program button three times
(once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.
♦ TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the
P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For
instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then
press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change
the program.
FAT BURN
POWER
CARDIO
START/STOP
WARM UP
PAUSE
ENTER
INCLINE
SPEED
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE-MS3200GT
♦ Plug treadmill into a surge protector outlet . Attach RED Safety Key to treadmill console.
♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.
♦ Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window
will flash.
♦ There are four (4) pre-set and eight (8) semi-custom pre-set programs on the MS3200GT. The treadmill
includes FAT BURN, CARDIO, WARM-UP, and CROSS TRAINING programs. Select the program by
pressing the appropriate button.
♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving.
♦ CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-up, Cross
Training) can be customized in the P1 or P2 mode. After making the program selection, the Calorie window will
read “OP”. The ”OP” refers to “original program” and is preset. The program name you select will display in
the diode light beside the program name. Press the same program button once more and the Calorie window will
read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode,
which will be saved for future workouts.
1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press
ENTER PROGRAM.
2) The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your
workout. Press ENTER PROGRAM.
3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press
ENTER PROGRAM.
To start, press the START/STOP button. To access P2 mode, press the selected program button three times
(once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.
♦ TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the
P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For
instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then
press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change
the program.
FAT BURN
POWER
START/STOP
PAUSE
CARDIO
WARM UP
CROSS TRAINING
USER PROGRAM
INCLINE
SPEED
ENTER
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
♦
Heart Rate Control Instructions (MS3200GT only)
♦ HEART RATE PROGRAM MODE
♦
The Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by automatically adjusting
the incline. For example, if you have programmed in a desired heart rate of 105 beats per minute and your heart rate is only
95 beats per minute (you must be wearing Heart Rate Transmitter), the incline will automatically increase to intensify the
work load, and increase you heart rate to the 105 beats per minute you programmed.
♦
If your heart rate is above your programmed amount of beats per minute the incline will automatically decrease to lower your
heart rate. You may at any time during the Heart Rate Program adjust/override the speed and or incline by simply pressing
the correct corresponding buttons. You may change your “Target Heart Rate” at any time during the program by pressing
the TARGET + or TARGET – buttons.
♦
♦
♦
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to console
Place the Heart Rate transmitter strap across chest against the skin. Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered.
The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart Rate Transmitter is
transmitting. Adjust the strap on the chest until the console is picking up a signal.
♦
For Quick Start, press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) buttons. Heart rate will read
out in the Incline window.
♦
♦
♦
♦
♦
To select the Heart Rate Control program, press the “Heart Rate Program” button.
The incline window will flash “125”, which is the default program target heart rate.
Adjust Target Heart Rate to desired level with the TARGET + or – buttons.
Press START/STOP button, or continue instructions below to program Time, and Speed.
You can now program the Time and Speed. The time window will blink. Use the SPEED + or – arrows to select your
workout time, then press the ENTER PROGRAM button. The SPEED window will now be flashing. Using the SPEED +
or – arrows, select the maximum speed for your workout, then press ENTER PROGRAM. To start, press the START/STOP
button.
TARGET DOWN
TARGET UP
POWER
START/STOP
ENTER PROGRAM
SPEED +/-
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Profiles
SPEED
SPEED
1
2
1
12
11
10
9
8
7
6
5
4
3
INCLINE
INCLINE
1
1
0
9
8
7
6
5
4
2
1
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
The Cardio Program is designed to vary
the treadmill Speed, while maintaining a
constant Elevation.
The Fat Burn Program is designed to
vary the treadmill elevation, while main-
taining a constant walking belt speed.
SPEED
SPEED
12
11
10
9
8
7
6
5
4
3
12
11
10
INCLINE
INCLINE
9
8
7
6
5
4
3
2
1
2
1
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
The Warm Up Program is designed to gradually
increase the treadmill Speed and Elevation in the
first segment (warm up) and gradually decrease
the treadmill Speed and Elevation in the last
segment (cool down). This is also known as a
Plateau program.
*The Cross Training Program is designed to con-
trol the walking belt speed and elevation inversely in
alternating segments.
*On the MS3200GT only.
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature
roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for
tension and centering. Your new treadmill comes pre-adjusted from
the factory for tension and centering. Please follow the procedures
below if the belt shifts to the left or right or while walking:
WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)
First, turn treadmill on to run at 1 mph. Using the hex key provided,
turn the left rear roller adjustment bolt ¼ turn in the clockwise
direction. Next, run the treadmill at 2.5 mph. You should see the
belt start to correct itself, moving back towards the center. Repeat the
above procedure until the walking belt is centered. It may be necessary
to set walking belt tension once you have completed this procedure if
the belt feels like it is slipping while walking. Refer below to the
“Walking Belt Slipping” instructions.
WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)
First, turn the treadmill on to run at 1 mph. Using the hex key
provided, turn the right rear roller adjustment bolt ¼ turn in the
clockwise direction. Next, run the treadmill at 2.5 mph. You should
see the belt start to correct itself, moving back towards the center.
Repeat the above procedure until the walking belt is centered. It may
be necessary to set walking belt tension once you have completed this
procedure if the belt feels like it is slipping while walking. Refer
below to the “Walking Belt Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using the hex
key provided, turn both left and right rear roller adjustment bolts the
same distance, usually a ¼ turn in the clockwise direction. Plug the
power cord back into the surge protector and run the treadmill at 2.5
mph. You should now walk on the belt to determine if the belt is still
slipping. Repeat the above procedure until the walking belt is not
slipping. The tension should be just tight enough not to slip.
♦ Turning the hex key counter clockwise brings the rear rollers and
belt towards you. Turning the hex key clockwise pushes the rear
roller and belt away form you.
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Miles per hour to Kilometers per hour
Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills
are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the
steps described here:
1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console.
2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the
console (see diagram below).
3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.
4) Pressing the SPEED +/- button will activate your choice.
5) To accept the setting, press the POWER button.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Treadmill will not start.
1) Is the RED Safety Key Attached to the Console?
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on
page 8)
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
5) Have an electrician check for inadequate voltage at the outlet.
Treadmill losses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the
outlet.
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section on page 14.
2) Need help? Call Keys Technical Service at (888) 340-0482.
Treadmill Error Messages.
Your treadmill is equipped with a software package that enables error messages to be displayed when
there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-0482.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts & Diagrams
1.
05-0037-Extrusion side board deluxe/left
2.
3.
4.
5.
05-0037-Extrusion side board deluxe/right
04-0008-Belt walk spliced 18 x 105WW
24-0006-Front roller assembly
09-0013-Rear roller assembly
03-0004-Walkboard waxed
6.
7.
06-0102-End cap
8.
9.
12-0022-Actuator 400lb Maytech
06-0018-Motor base pan
10.
06-0079-Small motor fan
11.
12.
12-0018-Motor MCM 2.0HP
04-0004-Poly V belt 190J8
13.
14.
06-0101-Motor cover w/wings
10-0020-Foam grips
15. & 16.
15. & 16.
17.
MS1200GT-24-0136 Console assembly
MS3200GT-24-0138-Console assembly
MS1200GT-08-0051-Motor controller
MS3200GT-08-0050-Motor controller
17.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
MS1200GT/MS3200GT- Parts List
Parts List -MS1200GT/3200GT
PART #
02-0002A
02-0004
02-0005
02-0006
02-0007
02-0008
02-0009
02-0013
02-0014
02-0015
02-0016
02-0017
02-0018
02-0019
02-0020
02-0021
02-0022
02-0024
02-0025
02-0027
02-0031
02-0033
02-0036
02-0040
02-0041
02-0050
02-0051
02-0053
02-0054
02-0068
DESCRIPTION
QTY PART #
06-0021
DESCRIPTION
CLAMP-WIRE 3367 7/16
QTY PART #
DESCRIPTION
SPRING-DECK LIFT
4
1
1
19-0032
19-0097
20-0003
20-0008
23-0001
18-0002
22-0001
23-0003
23-0090
19-0027
21-0002
21-0005
22-0025
20-0033
21-0018
02-0026
02-0028
02-0038
06-0024
06-0084
04-0004
14-0321
*06-0059
*13-0017
*24-0138
*15-0008
*06-0058
*08-0050
*19-0096
*07-0041
*02-0042
*07-0020
*14-0220
*06-0099
*26-0025
*15-0028
BRACKET-SPRING ANCHOR
BRACKET-ENCODER MCMILLAN
PROC-ACTUATOR EXTENSION TB-17-0011
PROC-BASE EXTENSION TB 17-0010
DECK FRAME ASSEMBLY
SCREW-8x5/8 PHIL PH AB BLACK
SCREW-8x5/8 PPH HILO BLACK TPB
BOLT-HEX 5/16-18x5 1/2 GRADE 5-ZP
NUT 5/16-18 NYLOCKZP
35 06-0022
8
GUIDE-RESET TUBE
1
3
3
3
8
06-0079
06-0088
06-0101
06-0102
06-0103
FAN-MCM MOTOR-5: W/ 1/2'SHAFT
SLEEVE-MOTOR TENSION 1/4"
COVER FOR MOTOR-GRAY
ENDCAP-GRAY
1
1
1
1
2
1
2
1
1
1
1
1
8
2
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
2
1
12
1
1
1
BOLT-HEX 5/16-18x3/4 GRADE 2-ZP
NUT-HEX 5/16 WIZ-FL-LK-ZP
WASHER LOCK 1/4"
ROD-LATCH
ACTUATOR CONNECTION ASSEMBLY
REAR ELEVATION ASSEMBLY WELDED
U/R ASSEMBLY STRAIGHT
COVER FOR MOLDED BASE-GRAY
BREAKER-CIRCIT-15AMP
SWITCH-REMOTE-W/HARNESS
ENCODER-OPTICAL-ALEPH
CONTROLLER-REVISED 08-0014
CORE-FERRITE
BOLT-HEX 1/4-20x2 1/2" GRADE 5 ZP
WASHER SPRING
11 08-0004
4
1
3
4
4
2
2
6
2
2
8
2
1
3
1
1
1
2
2
1
2
08-0027
08-0047
08-0051
08-0077
24-0006
09-0013
10-0002
10-0003
10-0004
10-0012
10-0017
11-0022
11-0003
12-0018
12-0022
13-0003
13-0007
13-0011
13-0016
14-0003
14-0023
14-0024
14-0025
14-0028
14-0352
14-0351
14-0089
14-0205
18-0006
19-0013
19-0134
19-0015
19-0019
06-0014
06-0016
06-0018
06-0019
06-0020
BRACKET PIVOT TUBE
BOLT-HEX 3/8-16x2 1/2" GRADE 5
NUT-NYLOCK HEX 3/8-16
BACE BRACE-FOOT LATCH-PUNCHED
BASE FRAME-W/DRAIN HOLES PUNCHED
UPRIGHT SUB-ASSEMBLY-STRAIGHT
PROC-REMOTE H/BAR 17-0005
CONSOLE PLATE-PUNCHED(19-0012)
NUT-PUSH PZ 001996
NUT-PUSH 3/8 HAT BLACK 375012
BOLT-CARRIAGE 10-24x1 1/2
SCREW 0SHCS 1/4-20x2 1/2"
WASHER 9/32 5/8 1/8THICK ZP
NUT-NYLOCK HEX 10-24
ROLLER-FRONT-20MM SHAFT
ROLLER-REAR-20MM SHAFT
ISOLATOR-BOARD
GRIP-FOAM 15x14.7
SWITCH-MAGNETIC KILL-YIHAN
WRENCH-ALLEN 3/16 SHAFT ARM
CLIP-ALLEN WRENCH
CARRIAGE BOLT 5/16x1 GRADE 5 ZP
AXLE-WHEEL 2"
FOOT-RUBBER
BUMPER-LATCH
NUT-T HF 14209H-DB
TAPE-FOAM-1"X75ft
BAG-PLASTIC 12x12 3ML-INST PACKET
BELT-POLY V 190J8
BOLT-HEX /8-16x1 3/4" GRADE 5ZP
WASHER-#10 EXTERNAL STAR
SCREW-PPH 8x5/8 GREEN HEAD
RETAINER-GUIDE TUBE
BUSHING-REAR ELEVAION
BUSHING-UPRIGHT PIVOT
MOTOR-MCM#253 1.75/2HP-REPLACES
ACTUATOR 40LB-MAYTECH
HARNESS-ENCODE
10-YEAR WARRANY DECAL
COVER-HRC RECEIVER-KES SERIES
HARNESS-TELCO-HRC
SCREW-PPH 8-18x5/8"S/D-FOOTLATCH
NUT-NYLOCK HEX 1/4-20
CONSOLE ASSEMBLY MS3200T
MANUAL-MS3200GT
WIRE-BREAKER 6"
SCREW-SH CAP 10-24x1 1/4"
SCREW-SHCS 1/4-20x3/4"
CORD-POWER-90"
SUPPORT-PC BOARD HRC
HARNESS-CONTROL PANEL
DECAL-MOTOR COVER SES- ALL GRAY
DECAL-NO LIFT ALL FOLDS
DECAL-SAFETY LACH-ALL FOLDS
DECAL-WARNING FOLDING-AL FOLDS
DECAL-CIRCUIT BREAKER ALL
DECAL-INCINE REMOTE
CONTROLLER-REPLACES 08-0013
BRACKET-HR RECEVER MOUNTING
CHEST STRAP NO LOGO-HR UNITS
SCREW-#8x5/8" S BLACK
SCREW-HWH MACH 8-32x3/8"
WASHER-FLAT SAE 5/16
02-0092
02-0108
02-0113
02-0123
03-0004
04-0008
05-0011
05-0014
05-0037
06-0103
06-0004
06-0005
06-0009
06-0133
06-0012
06-0125
SCREW-PHTR #8x3/" AB BLACK
SCREW-PPH 10-5/8"
7
1
1
2
1
1
1
1
2
1
2
2
4
4
2
2
RECEIVER-DISCRETE-LED-HC
DECAL-MOTOR COVER-MS3200GT
CONSOLE LED GRAY
SCREW-HWH SLOTTED 8-18x3/4"AB ZP
WASHER-FENDER 1/4x1"
WALKBOARD-WAXED
DECAL-SPEED REMOTE
INSTRUCTION PACKET-MS3200GT
WIRING DIAGRAM-McMILLAN
DECAL-STARBURST-WAX DECK/YELLOW
DECAL-DISCONNECT-MOTOR COVER
SPRING-MOTOR TENSION-PRESET
LATCH-FOOT LOCKING MECHANISM
BRACKET-BASE ELEVATION
BRACKET-MOTOR COVER
GUIDE BELT GLAVANIZED
BUSHING-STRAIN RELIEF #1237
TIES-WIRE
BELT-WALK-SPLICED 18x105WW
EXTRUSION-END CAP JOINT
BOTTOM PAN JOINT 21 1/2
EXTRUSION-SIDE BRD-DELUX-GRAY
PULLEY-8 GROOVE-190JA
PLUG-BASE 1.5x3:-16GA
PLUG-DOME 1.5-16GA
GLIDE-BASE EXTENSION
WHEEL-ROLLER 2"
PAN-MOTOR BASE
WHEEL 3"
PAN-CENTER BASE
SPACER FOR UPRIGHT
PAN-END-BASE
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
KeysMilestone 1200/3200GT Treadmill KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the
KEYS brand name. The warranty period on the MILESTONE 1200GT/3200GT to the original purchaser is (lifetime) on the frame, (10) years on the motor, (2) years parts,
and (1) year labor.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship
under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not
transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness
authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless
accompanied by written authorization by Keys Fitness).
During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty
under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in
performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to
Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible
for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of
alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered
defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or
(e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any
Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements
for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE
RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty
gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to
assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR TREADMILL
WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL WARRANTY CARD TO:
KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355.
KEYS FITNESS TREADMILL WARRANTY REGISTRATION
TELEPHONE
LAST
M.I.
FIRST
ADDRESS
CITY
APT. NO.
ZIP
STATE
SERIAL NO.
DATE OF PURCHASE
MODEL NO.
How important are each feature:
Least
Unique Features
Horsepower
Warranty
Price
Other Comments:
_______________
Where did you learn about treadmills?
TV____ Radio____ Friend____
Name of store or company where
purchased:
Most
_______________
_______________
_______________
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
How do you plan to use the treadmill?
Walk____ Run_____ Both_____
Look/Design
Folding Feature
Who will use the treadmill?
Male____ Female_____ Both_____
Why did you purchase a treadmill?
KEYS FITNESS respects the rights of your privacy. Our company
will not sell or distribute to others the information above. This
information is used to track our product quality and to contact you in
the event of a product safety concern. It may be used to offer you
future Keys products only through the mail. Please check here if wish
not to receive any additional information on Keys products.
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
How many family members? _____
AGE:
15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
Other __________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|