Alliance 850 / 880HR TREADMILL
OWNER’S MANUAL
Alliance Fitness Treadmills
Manufactured in the USA by:
KEYS Fitness Products, LP
P.O. Box 551239
Dallas, Texas 75239
(214) 340-8888
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
NING!
1) WARNING: Before using this treadmill or starting any exercise program, consult your physician. This is
especially important for persons over the age of 35 and/or persons with pre-existing health problems. The
manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through
the use of this product.
2) WARNING: To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important
to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
„
It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar
with warnings and safety precautions.
„
„
This treadmill has a maximum user capacity of 400 pounds.
The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not
be placed in a garage, patio, or near water and should never be used while you are wet. A treadmill mat is
recommended to protect the floor or carpet and for easier cleaning.
„
„
Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels
and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed
power cord.
Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with
bare feet, sandals, socks or stockings.
„
„
„
„
„
„
„
„
„
„
Always straddle the belt and allow it to start moving before stepping onto the belt.
Hold on to handrails when adjusting speed, incline, or other controls.
Always examine your treadmill before using to ensure all parts are in working order.
Allow the belt to fully stop before dismounting.
Pets should be never be allowed near or on the treadmill.
Do not leave children unsupervised near or on the treadmill.
Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.
Never insert any object or body parts into any opening.
For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by
an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow
these instructions will void the treadmill warranty.
„
Never leave the treadmill unattended while it is running.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start
Thank you for purchasing an Alliance treadmill! The Alliance treadmill you have chosen
was designed to meets your needs for cardiovascular exercise.
• Before you start, please read the Owner’s Manual and become familiar with the
operation of your new treadmill.
• Remember to take the time to perform the stretching exercises
provided to avoid injury.
• Do not stand on the walking belt while pressing the Power or Start/Stop button.
• Always adjust the speed of the treadmill in small increments as this treadmill is capable
of high speeds.
• If you are taking medication, consult your physician to see if the medication will affect
your exercise heart rate.
• If you have heart problems, you are not active, and/or are over the age of 50 years, do
not use the pre-set treadmill programs or start an exercise program without first
contacting and receiving approval from your physician.
• To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids
on the console. The manufacturer recommends a sealed water bottle for beverages
consumed while using the treadmill.
• Please review the following drawing below to familiarize yourself with the listed
parts. This manual covers several treadmills, so the one pictured below may not
be identical to your particular model.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warm Up Exercises
NING!
WARM UP FIRST !
Warming up prepares the body for exercise by increasing circulation, supplying more
oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10
minutes of stretching and light exercise to warm up. The drawings on this page show
several forms of basic stretching you may perform before your workouts. Again, consult a
physician before starting this or any other exercise program.
15 Seconds for each
20 Seconds
20 Seconds
20 Seconds
30 Seconds
20 Seconds
20 Seconds
25 Seconds
30 Seconds
25 Seconds each leg
20 Seconds
5 Seconds X 3 times
25 Seconds each leg
5 Times
15 Seconds
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Instructions
Minor Assembly Required!
Alliance 850 and 880HR treadmills are shipped in two pieces: the console upright assembly and
the base assembly. After opening the box, remove any packing materials from the treadmill. Do
not throw away any packing materials until the unit is working properly. The treadmill box
contains a package that includes the Owners Manual, a RED SAFETY KEY, and a belt
adjustment tool. The 880HR will also contain the heart rate chest strap. The treadmill will not
operate without the Red Safety Key.
The console upright assembly is attached to the base assembly. Place the unit on a clean, level
surface near an electrical outlet (extension cords are not recommended).
1. Raise the console into an upright position. Loosely install both 3/4” buttonhead screws on
each side of the upright. Install and tighten each 3 1/2” x 5/16” bolt (2) with washers from the
bottom of the base frame through the upright lock (diag. 1).
2. Now tighten the buttonhead screws securely from step 1.
3. Tighten the black, flathead pivot bolts on the inside of upright.
4. Install motor hood cover using 5/8” phillips head screws (8 screws).
Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill.
Assembly is now complete!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Requirements
WARNING!
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT
IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR
SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY
GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED
ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage
spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or
off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge
protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage
rating of 400V or less and an electrical rating of 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance
for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an
equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug
the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the
drawing (1) below.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
START/STOP - This button
starts the treadmill belt
moving. There is a 4 second
countdown built in as a safety
feature to let you know the
treadmill belt is about to start
moving.
Use the START/STOP button
also to stop your treadmill
after your workout. The belt
will gradually come to a stop
after pressing the button.
PROGRAM BUTTONS - These buttons are used to
access each of the three programs: Fat Burn, Cardio,
and Warm Up. Each program has one preset program,
and two additional custom programs in the P1 and P2
mode. See the “Program and Operating Instructions” on
page 12.
POWER - Press to on. Allow
6-8 seconds while the
electronics perform a self
check prior to pressing other
PAUSE - Press to
temporarily pause
your workout
while in use. The
treadmill is
designed with an
automatic power
off feature after 5
minutes in the
ENTER - Use
the Enter button
while setting
program time,
speed, and
pause mode.
incline options.
See page 12 for
complete
SPEED - Use to either
increase (UP arrow) or
decrease (DOWN arrow)
the speed. These buttons
are also used while
INCLINE - Use to either
increase (UP arrow) or
decrease (DOWN arrow)
the incline. These buttons
are also used while
CONSOLE SAFETY KEY - Place the RED
Safety Key here prior to turning power on.
THE TREADMILL WILL NOT OPERATE
WITHOUT THE SAFETY KEY ATTACHED.
The safety key is equipped with a string and
clip that will clip to your clothing. This is an
important safety feature that will automatically
turn the power off if you should trip or fall
while using the treadmill.
programming SPEED and
TIME.
programming INCLINE.
ONE TOUCH INCLINE
BAR - Use to either increase or
decrease the incline. Each
number indicates percent of
grade. Pressing one of the
buttons will gradually increase
or decrease the incline to the
ONE TOUCH SPEED BAR -
Use to either increase or
decrease the speed. Each
number indicates MPH.
Pressing one of the buttons will
gradually increase or decrease
the speed to the new setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
There are five display windows on the control panel to provide feedback information.
TIME WINDOW
•
TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59
seconds)
•
INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and
counting to 0 seconds
SPEED WINDOW
•
SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments
DISTANCE / CALORIES WINDOW
•
DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments
starting at 10.0
•
CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed,
incline, and time
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Console Functions and Descriptions
INCLINE WINDOW
•
•
•
INCLINE: Indicates incline in percent of grade 0-12% in 1 increments
PULSE (880HR Model Only): Indicates current heart rate
HEART “♥” (880HR Model only): Indicates control panel is receiving a signal from heart rate
transmitter. Heart will blink on and off if receiving signal from Heart Rate Transmitter chest strap.
CENTER BRICKYARD WINDOW
•
Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode,
shows the change in speed profile across the interval range (1-10) and shows position with a blinking
action.
The 880HR will display the name of the program selected, showing on the left hand side of the window. The LAP
counter will appear in manual mode in the center of the window.
SPEED & INCLINE “ONE-TOUCH” BUTTONS
•
Easy One-Touch buttons for Speed and Incline have been added to the console. To increase or
decrease the speed, simply choose the desired setting (each number 2 through 8 represents Miles
per Hour). To increase or decrease the amount of incline, simply choose the desired setting (each
number 2 through 8 represents percent grade).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
QUICK START / MANUAL MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
ATTACH THE RED SAFETY KEY TO CENTER OF CONSOLE.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving. Speed or incline may be adjusted by using the appropriate UP (increase) or DOWN (decrease) buttons.
Speed and Incline can also be adjusted using the “One Touch” buttons labeled 2 through 8, or by using the toggle
switches located on the handlebars. For speed and incline adjustments while using the treadmill, try the
convenient handlebar toggles switches. The left handlebar switch is for incline, while the right handlebar switch
adjusts the speed.
•
•
•
To end your workout, press START/STOP button. Belt will gradually slow to zero.
To pause your workout, press PAUSE. The treadmill will automatically shut off after five (5) minutes.
To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume at the speed the
treadmill was moving before pausing.
•
Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting
started. After pressing the POWER button, the time window will blink. Use the SPEED UP or DOWN arrows to
select your workout time, then press the ENTER button located on the left hand side of the console below the
program buttons. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select the
speed for your workout, then press ENTER. Now the INCLINE window will be flashing. Use the INCLINE + or –
arrows to set your workout incline, then press ENTER. To start, press the START/STOP button.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
PROGRAM MODE
•
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit).
ATTACH THE RED SAFETY KEY TO THE CENTER OF THE CONSOLE.
Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash.
•
There are three (3) pre-set programs on the 850 and 880HR. Both include Fat Burn, Cardio, and Warm Up
programs. The 835HR also includes a Heart Rate Control program (see the program profiles later in this
manual). Select the program by pressing the appropriate button.
•
•
•
Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts
moving.
Each of the pre-set programs (6) can also be customized. Follow the instructions below for your
particular model.
Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the P1 or P2 mode.
After making the program selection, the center window will read “OP.” ”OP” refers to “original program” and is
preset. Press the same program button once more, and the center window will read P1. The “P1” mode is now
accessed. You can now program the Time, Speed, and Incline in P1 mode, which will save your entered
information for future use. The time window will blink. Use the SPEED UP or DOWN arrows to select your
workout time, then press the ENTER button located on the left hand side of the console below the program
buttons. The SPEED window will now be flashing. Using the SPEED UP or DOWN arrows, select the speed for
your workout, then press the ENTER button. Now the INCLINE window will be flashing. Use the INCLINE UP or
DOWN arrows to set your workout incline, then press the ENTER button. To start, press the START/STOP
button. To access P2 mode, press the selected program button three times (once for OP, twice for P1, three
times for P2). Follow the above procedure to customize.
•
TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1
or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For
instance, if P1 in Fat Burn has been programmed, to change to a new setting, press the Fat Burn button twice to
access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to
continue to change the program.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and Operating Instructions
Heart Rate Control Instructions (880HR only)
HEART RATE PROGRAM MODE
The Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by automatically
adjusting the incline. For example, if you have programmed in a desired heart rate of 105 beats per minute and your
heart rate is only 95 beats per minute (you must be wearing Heart Rate Transmitter), the incline will automatically
increase to intensify the work load, and increase you heart rate to the 105 beats per minute you programmed.
If your heart rate is above your programmed amount of beats per minute the incline will automatically decrease to
lower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and or incline
by simply pressing the correct corresponding buttons. You may change your “Target Heart Rate” at ant time during
the program by pressing the TARGET + or TARGET – buttons.
•
•
•
Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to console
Place the Heart Rate transmitter strap across chest against the skin. Stand on the treadmill and straddle belt.
Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can
be entered. The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart Rate
Transmitter is transmitting. Adjust the strap on the chest until the console is picking up a signal.
•
For Quick Start, press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after
the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease)
buttons. Heart rate will read out in the Incline window.
•
•
•
•
•
To select the Heart Rate Control program, press the “Heart Rate Control” button.
The incline window will flash “125”, which is the default program target heart rate.
Adjust Target Heart Rate to desired level with the TARGET + or – buttons.
Press START/STOP button, or continue instructions below to program Time, Speed and Incline.
You can now program the Time, Speed, and Incline. The time window will blink. Use the SPEED/TIME + or –
arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will
now be flashing. Using the same + or – arrows, select the maximum speed for your workout, then press ENTER
PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your maximum
workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Profiles
The FAT BURN program is designed to vary
treadmill elevation while maintaining a constant
walking speed. Set the desired maximum speed
and incline, and the treadmill will automatically
change the incline to the set amount, alternating
in segments 2-3, 5-6, and 8-9.
The CARDIO program is designed to vary
treadmill speed while maintaining a constant
incline. Set the desired maximum speed and
incline, and the treadmill will automatically
change the speed to the set amount, alternating
in each segment.
EACH PROGRAM HAS 10 SEGMENTS. THE
LENGTH OF TIME FOR EACH SEGMENT IS
BASED ON THE TIME LENGTH OF THE
PROGRAM. IF YOU SET THE PROGRAM TO 30
MINUTES, EACH SEGMENT IS 3 MINUTES LONG
(TIME divided by 10 segments).
YOU CAN ALSO CUSTOMIZE THE TIME, SPEED,
AND INCLINE FOR EACH OF THESE
PROGRAMS. SEE PAGE 12 FOR PROGRAMMING
THE P1 AND P2 MODES.
The WARM UP program is designed to gradually
increase treadmill speed and incline (warm up) in
the first segment to the set maximum speed and
incline. At the end of the program, the treadmill
will gradually decrease speed and incline to half of
the maximum set (cool down) in segments 9-10.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!
Belt adjustment and tension performs two functions: adjustment for tension and centering. Your
new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the
procedures below if the belt shifts left or right or if the belt slips while walking:
WALKING BELT HAS SHIFTING TO THE LEFT (Diagram 1)
First, unplug the power cord from the surge protector. Using the hex key provided, turn the left
rear roller adjustment bolt ¼ turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself,
moving back towards the center. Repeat the above procedure until the walking belt is centered.
It may be necessary to set walking belt tension once you have completed this procedure if the belt
feels like it is slipping while walking. Refer to below to the “Walking Belt Slipping” instructions.
WALKING BELT HAS SHIFTING TO THE RIGHT (Diagram
2)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn the right rear roller adjustment bolt
¼ turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You
should see the belt start to correct itself, moving back towards
the center. Repeat the above procedure until the walking belt
is centered. It may be necessary to set walking belt tension
once you have completed this procedure if the belt feels like it
is slipping while walking. Refer to below to the “Walking Belt
Slipping” instructions.
WALKING BELT IS SLIPPING DURING USE (Diagram 3)
First, unplug the power cord from the surge protector. Using
the hex key provided, turn both left and right rear roller
adjustment bolts the same distance, usually a ¼ turn in the
clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should now
walk on the belt to determine if the belt is still slipping. Repeat
the above procedure until the walking belt is not slipping. The
tension should be just tight enough not to slip.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug
the power cord from the surge protector.
CLEANING
Routine cleaning of your Alliance Fitness treadmill will extend the life of your treadmill. WARNING! To prevent
electrical shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet
before attempting any cleaning or maintenance.
AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft
cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be
checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be
lubricated usually within the first year or 500 hours of use. If you have questions, call us at (888) 340-0482.
Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board
as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the
touch, follow the instructions below.
Please use Lube ‘N Walk (can be purchased from your dealer or call the number on the front of the manual), or a
non-petroleum based silicone such as “Napa 8300” (available at most stores).
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board
approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front
of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.
4) Allow the silicone to ‘set’ for one minute before using the treadmill.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Treadmill will not start.
1) Is the RED Safety Key Attached to the Console?
2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a
properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)
3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
5) Have an electrician check for inadequate voltage at the outlet.
Treadmill looses power during use.
1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.
Wait five minutes and then press the switch back in.
2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.
If it has tripped, reset or have an electrician replace the breaker in home.
3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slows during use.
1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15
amps, with a 14-guage cord of five feet or less and the surge protector is securely plugged into the
outlet.
2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.
Treadmill walking belt slips or is not centered on rear roller.
1) Refer to “Belt Adjustment and Tension” section.
2) Need help? Call Keys Technical Service at (888) 340-0482.
Treadmill Error Messages.
2)Your treadmill is equipped with a software package that enables error messages to be displayed when
there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not
operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-
0482.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts & Exploded View
Part #
Part #
1
2
3
4
5
Left Side Extrusion Rail
Right Side Extrusion Rail
Treadmill Belt
05-0013
05-0012
04-0010
24-0106
09-0009
12 Front Wheel (2)
06-0039
various
13 Uprights for Console (2)
14 Motor Hood Cover Top
15 Motor Drive Belt
06-0040
04-0007
12-0002
12-0013
12-0010
24-0091
24-0092
various
Front Roller Assembly
Rear Roller
16 Motor (850)
Motor (880HR)
6
7
8
9
Treadmill Deck
03-0005
06-0043
06-0042
10-0008
various
17 Elevation Motor (acuator)
18 Console Assembly (850)
19 Console Assembly (880HR)
20 Handlebars
Left End Cap
Right End Cap
Rear Adjustable Foot (2)
10 Main Frame
21 Toggle switches (2)
22 Lower Electronics M/Control P/Supply
08-0035
08-0016
11 Bottom Motor Pan
06-0041
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Alliance 850 and 880HR Treadmills manfactured by KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY
PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.
This Limited Warranty applies in the United States, Canada, and Mexico to products manufactured or distributed by Keys Fitness Products, LP (“Keys”)
under the ALLIANCE brand name. The warranty period to the original purchaser is (lifetime) on the frame, (5) years on the motor, walking belt, and deck, (2) years on
parts, and (1) year labor. This warranty does not cover wear and tear, only manufacturer defects for the periods specified.
Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller
is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your
proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from
you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician
unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the
warranty will be void unless accompanied by written authorization by Keys Fitness). Select models do not require assembly, and the original purchaser
During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the part or product if it becomes defective, malfunctions, or
otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace
defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this
warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.
To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts
determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any
other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You
assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration,
erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.
This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any
Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by
modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized
Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product be
submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt
of payment or acceptable arrangements for payment.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS
LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS
NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This
is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty.
PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR
TREADMILL WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL
WARRANTY CARD TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355.
KEYS FITNESS TREADMILL WARRANTY REGISTRATION
TELEPHONE
LAST
M.I.
FIRST
ADDRESS
CITY
APT. NO.
ZIP
STATE
SERIAL NO.
DATE OF PURCHASE
MODEL NO.
How important are each feature:
Least Most
Unique Features
Horsepower
Warranty
Price
Look/Design
Folding Feature
Other Comments:
_______________
Where did you learn about treadmills?
TV____ Radio____ Friend____
Name of store or company where
purchased:
_______________
_______________
_______________
In Store Display____ Salesperson___
Print ad/flyer____ Internet______
How do you plan to use the treadmill?
Walk____ Run_____ Both_____
Who will use the treadmill?
Male____ Female_____ Both_____
Why did you purchase a treadmill?
KEYS FITNESS respects the rights of your privacy. Our
company will not sell or distribute to others the information
above. This information is used to track our product
quality and to contact you in the event of a product safety
concern. It may be used to offer you future Keys products
only through the mail. Please check here if wish not to
receive any additional information on Keys products.
Dr.’s Orders____ Loose Weight____
In-home convenience____
Improve Cardiovascular Fitness___
Safety from outdoors____
How many family members? _____
AGE:
15-24____ 25-34____
35-44____ 45-54____
55-64____ 65 +_____
Other __________________________
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|