Owner’s manual
Special Edition/Signature B60 Keurig® Brewer
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS Safe Operation & Use
CAUTION: There are two sharp needles that puncture the K-Cup® pack, one
above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack
Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pack
Assembly Housing.
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
Special Edition/Signature B60 —Using Your Brewer
When using electrical appliances, basic
safety precautions should be followed,
including the following:
11. For best operation, plug the appliance
into its own electrical outlet on a
dedicated circuit to prevent flickering
of lights, blowing of fuses or tripping a
circuit breaker.
electrical short circuit, grounding
reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
20.Do not, under any circumstances, cut or
remove the third (ground) prong from
the power cord or use an adapter.
21. Consult a qualified electrician if
the grounding instructions are not
completely understood, or if doubt
exists as to whether the appliance is
properly grounded.
CAUTION: There is extremely hot water in the K-Cup® Pack Holder during the
brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup®
Pack Assembly Housing during the brewing process.
SET-UP
1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles
and knobs when available.
Helpful Hints........................................................................................4
Unpacking ............................................................................................4
Features ...............................................................................................5
12. Do not operate any appliance with a
damaged cord or plug or after
the appliance malfunctions or is
damaged in any manner. Contact
Keurig Customer Service to report
any malfunction of or damage to the
Brewer.
13. Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
14. To disconnect, press the Power Button
on the Brewer to ‘OFF’ status and then
remove the plug from the wall outlet.
15. Close supervision is necessary when
any appliance is used by or near
children.
CAUTION: Please always keep the Brewer in its upright position to avoid
potential injury and/or damage to your Brewer.
3. This appliance must be properly
installed and located in accordance
with these instructions before it is used.
4. The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5. Do not place on or near a hot gas or
electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock
and injury do not immerse cords, plugs,
or the appliance in water or any other
liquid.
8. Do not overfill the Water Reservoir
with water.
9. Use only water in this appliance! Do
not put any other liquids or foods in the
Water Reservoir except as instructed in
the Cleaning Instructions in this guide.
10. Turn off and unplug the Brewer before
cleaning or maintenance. Allow to cool
before putting on or taking off parts
and before cleaning the appliance.
SECTION 1—SET-UP & FIRST BREW
Set-Up & First Brew...........................................................................6
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to
reduce the risk of becoming entangled in or tripping over a longer cord.
SECTION 2—CONTROLS & INDICATORS
If an extension cord is used, (1) the marked electrical rating of the cord set or
extension cord should be at least as great as the electrical rating of the
appliance; (2) the cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or tripped over
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
Setting the Clock...............................................................................10
Programming On/Off Features ......................................................10
Programming Brew Temperature .................................................12
22.Do not use the appliance for other than
its intended use.
SECTION 3—CLEANING & MAINTENANCE
Cleaning..............................................................................................12
De-Scaling..........................................................................................13
Storage ...............................................................................................14
SavE THESE
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
INSTRUCTIONS.
WaRNING TO USERS aND PaRENTS
1. DO NOT permit children to use Brewer
unless there is adult supervision. Brewer
dispenses very hot water.
WARNING
THIS PRODUCT CONTAINS CHEMICALS, INCLUDING
16. Do not lift the Brewer Handle while
brewing is in progress.
17. Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
SECTION 4—TROUBLESHOOTING..................................................15
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
SECTION 5 —WARRANTY................................................................16
2. SPECIaL NOTICE FOR HOT COCOa USERS:
IMMEDIaTELY aFTER USING a HOT COCOa
K-CUP® PaCK, RUN a Hot Water Brew Cycle
without a K-Cup® pack to avoid the possibility
of clogging the exit needle. DO NOT assume
the next user will do this.
Record your Brewer Serial Number here.
See Unpacking Instructions on page 4 for serial number location.
18. This appliance is equipped with a power
cord having a grounding wire with a
grounding plug. The appliance must
be grounded using a 3-hole properly
grounded outlet. In the event of an
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
BOTTOM COVER. NO USER SERVICEABLE
WARNING
RISK OF FIRE OR
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
ELECTRIC SHOCK
Removing the serial number label from the Brewer will void warranty.
!
DO NOT OPEN
BY AUTHORIZED SERVICE PERSONNEL ONLY.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up
Features Special Edition/Signature — Model B60 Brewer
4. Customize the size, flavor & brew that’s
perfect for you.
2. Remove enclosed literature.
Helpful Hints
T
D
G
3. Turn the box on its side with front of box
face down.
With the choice of over 200 varieties of
K-Cup® packs and 3 brew sizes (Small Cup-
5.25 oz., Small Mug-7.25 oz. and Large
Mug-9.25 oz.), your Keurig® Brewer gives you
endless options to customize the size, flavor
and brew that’s perfect for you. For a strong,
intense cup, select an Extra Bold K-Cup®
pack (with up to 30% more ground coffee than
regular varieties) and brew size that’s right
for you. The smaller the brew size, the more
intense flavor in your cup. The larger the brew
size, the less intense flavor in your cup.
1. Plug Brewer into its own grounded outlet.
If the electric circuit is overloaded with other
appliances, your Brewer may not function
properly. The Brewer should be operated on
its own circuit, separate from other appliances.
a
4. Reach into the box and grasp the plastic bag
that contains the Brewer.
READY
TO BREW
M
5. Carefully pull the plastic bag (and packaging
materials) toward you and out of the box. The
Brewer will still be encased in the polyfoam
and be on its side.
S
:
11 56
AM
2. Keep your Brewer turned “ON.”
F
MENU
H
To brew a fresh cup of coffee, tea or hot cocoa
anytime you want, keep your Brewer turned
“ON” all the time. However, the Brewer is fully
programmable so you can set it to turn on and
off automatically to match your schedule.
Or, if you prefer, set the Brewer to automatically
turn off after a period of time. Follow the simple
instructions on pages 10–12 to find the settings
that are most convenient for you.
E
C
I
R
B
6. Remove the top polyfoam packaging material.
7. Carefully lift Brewer off of the bottom polyfoam
and place it upright on a flat, steady surface.
N
J
5. Remove K-Cup® pack after use.
Please see page 7 for brewing instructions.
8. Lift plastic bag off of Brewer.
9. Record the serial number for this Brewer on
page 3 of this guide. The serial number can
be found on the bottom of the Brewer box or
on the Brewer behind the Drip Tray (when
removed).
6. Brewing into a travel mug.
0
P
Q
K
To brew into a travel mug, simply remove the
Drip Tray Assembly and place the travel mug
on the Drip Tray Base.
3. For the best tasting gourmet coffee, tea or
hot cocoa, Keurig recommends using bottled
or filtered water.
L
Water quality varies from place to place.
If you notice an undesirable taste in your cup
of coffee, such as chlorine or other mineral
tastes, we recommend you consider using
bottled water or water from a filtration
system. For best results, carefully follow
manufacturer’s instructions when using any
water filtration system.
7. De-scale Brewer regularly.
Please see pages 13 and 14 for instructions.
10. Place the Brewer upright on a flat, steady
surface. Remove tape holding Water Reservoir
in place.
Special Edition/Signature B60 Brewer
Controls and Indicators
A. Water Reservoir Lid
B. Water Reservoir
C. Water Reservoir
Lock Tab Slots
D. Handle
F. K-Cup® Pack Holder
(E and F are the K-Cup®
Pack Holder Assembly)
G. Lid
J. Drip Tray Plate
K. Drip Tray
L. Drip Tray Base
M. Vent
O. Small Cup Button 5.25 oz.
P. Small Mug Button 7.25 oz.
Q. Large Mug Button 9.25 oz.
R. Menu Button
S. LCD Control Center
T. Power Button
Unpacking Instructions
We recommend you save all packing materials in
case future shipping of the product is necessary.
1. Place Brewer box on a large steady surface
(such as a table or countertop) or on the floor.
Open the box.
H. K-Cup® Pack
Assembly Housing
I. Housing
N. Power Cord
WARNING:
Keep all plastic bags away
from children.
E. Funnel
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 Set-Up & First Brew
8. The Brewer will automatically fill the
internal tank with water and then the water
will be heated. This will take about 4 minutes.
During the heating period, “NOT READY”
(fig. 4) is indicated on the LCD Control
Center. Do not lift Handle during this
heating period.
Ready to Brew Your First Cup
IMPORTaNT: You cannot use your Keurig® Brewer until
2
fig.
fig.
4
fig.
Lock Tabs
6
4. Fill Water Reservoir with bottled or filtered
water so that the water level is just below the
top edge of the Water Reservoir.
1. LCD Control Center will indicate
“READY TO BREW.”
it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to
reach room temperature before brewing. A frozen
or extremely cold Brewer will not operate.
NOT READY
2. Place a cup or mug on the Drip Tray Plate.
5. Place Water Reservoir base into the left side
of the Brewer and be sure the Water Reservoir
Lock Tabs engage with the Brewer. Replace
Lid on Water Reservoir.
3. Lift the Handle and the K-Cup® Pack Holder
will open toward you (fig. 6).
Once the water is heated, “READY TO BREW”
will be indicated and the Brew Buttons will be
illuminated (fig. 5). NOTE: You may see small
amounts of water coming from the Vent and
dripping into the Water Reservoir during this
and subsequent heating—this is normal.
4. Select a K-Cup® pack.
NOTE: Do not remove the foil
lid or puncture the K-Cup® pack.
6. Press the Power Button found directly
above the LCD Control Center (fig. 3).
fig.
1
5. Place a K-Cup® pack in the
K-Cup® Pack Holder (fig. 7).
Setting Up Your Brewer
7. The LCD Control Center will illuminate and
indicate “NOT READY.” NOTE: A K-Cup® pack
should not be used for this sequence.
1. Unwrap cord and plug the Brewer into
a grounded outlet. Remove all pieces of
packing tape and clear plastic sticker
from LCD Control Center.
CAUTION: There are two sharp needles that
puncture the K-Cup® pack, one above the
K-Cup® Pack Holder and the other in the bottom
of the K-Cup® Pack Holder. To avoid risk of
injury, do not put your fingers in the K-Cup®
Pack Assembly Housing.
9. Lift and lower the Handle. Press the Small
Mug Button to start a cleansing brew. Pour
the hot water into the sink.
fig.
3
fig.
5
NOTE: If the Water Reservoir is empty or
not in place on the Brewer, the LCD Control
Center will also indicate “ADD WATER.” None
of the buttons will be activated until water
is added to the Water Reservoir and Water
Reservoir is in place.
Power
fig.
7
10. The one-time set-up process is now
complete and you are ready to brew!
NOTE: The Brewer may take 15 seconds
between brews and then “READY TO BREW”
will be indicated.
NOT READY
READY
2. Place a large mug (10 oz. minimum) on the
Drip Tray Plate.
TO BREW
ADD
WATER
MENU
3. Remove the Water Reservoir from Brewer
by first removing Lid from Reservoir (fig. 1),
then lifting Reservoir straight up and away
from Brewer (may be tight), (fig. 2). Rinse
with fresh water.
6. Lower the Handle to close the Lid over the
K-Cup® Pack Holder. (When it is closed
completely, the LCD Control Center will
indicate “READY TO BREW” and the Small
Cup, Small Mug and Large Mug Buttons will
flash for up to 60 seconds.)
Small
Mug
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 Set-Up & First Brew
Ready to Brew Your First Cup (Continued)
10. Lift the Handle, remove and dispose of the
used K-Cup® pack. CAUTION: K-Cup® pack
will be hot.
adding Water
Brewing Hot Water
7. Choose the cup size of coffee, tea or hot
cocoa by pressing the button that indicates
your choice. The Small Cup choice will yield
a 5.25 oz. serving, the Small Mug choice will
yield a 7.25 oz. serving and the Large Mug
choice will yield a 9.25 oz. serving. NOTE: If
you do not push a Brew Button in 60 seconds,
the LCD Control Center will return to “READY
TO BREW” and the Brew Buttons will be
disabled to prevent accidental activation.
Re-activate the Brew Buttons by raising and
lowering the Handle completely.
The LCD Control Center will indicate “ADD
WATER” when the water level in the Water
Reservoir is low or if the Water Reservoir has
been removed (fig. 8). The blue light in the Water
Reservoir will also blink when water needs to be
added. The Brewer will not allow you to brew when
“ADD WATER” is indicated.
Your Brewer is able to produce hot water for making hot cocoa from a packet,
for use in cooking, for making soups, etc. Simply follow the instructions on
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup® pack.
NOTE: After brewing a hot cocoa K-Cup® pack, we recommend running a
cleansing brew without a K-Cup® pack.
fig.
8
11. Enjoy your first cup of Keurig Brewed®
Small Cup
gourmet coffee, tea or hot cocoa!
(5.25 oz.)
12. Your Brewer may indicate “NOT READY” as it
heats water for the next brew cycle. The
“READY TO BREW” indication will return to
the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will
fill in preparation for the next brew. The pump
will make a vibrating sound. This is normal.
NOT READY
ADD
WATER
Purging the Brewer
The Water Reservoir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour water
directly into the Water Reservoir while it is still
attached to the Brewer, then replace the Lid.
If your Brewer has not been used for more than one week, you should purge
the water from the inner tank.
Small Mug
(7.25 oz.)
1. If there is water in the Water Reservoir, remove the Lid, then lift the
Water Reservoir straight up and away from Brewer. Discard water, rinse
and refill with water. Place the Water Reservoir back on the Brewer and
replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Remove the Water Reservoir from Brewer by first removing Lid from
the Water Reservoir, then lifting the Water Reservoir straight up and
away from Brewer. Fill with water. Place the Water Reservoir back on
the Brewer and replace the Lid. IMPORTANT: Do not remove the
Water Reservoir during the brewing process.
8. The LCD Control Center will indicate
“BREWING” and the cup size you selected
will illuminate. CAUTION: There is extremely
hot water in the K-Cup® Pack Holder during the
brew process. To avoid risk of injury, do not lift
the Handle or open the K-Cup® Pack Assembly
Housing during the brew process.
Stopping the Brew Process
If you need to stop brewing after the process has started, press the Power
Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop,
the heating element will shut off, and the blue lights illuminating the brew
buttons and Water Reservoir will disappear. NOTE: You may get less coffee, tea
or hot cocoa in your cup during your next brew. We recommend that you perform
a cleansing brew after a terminated brew. Then your NEXT brew will be the
volume you have selected.
2. Be sure the Brewer is turned on. Raise and lower the Handle on the
Brewer without inserting a K-Cup® pack.
Large Mug
(9.25 oz.)
3. The LCD Control Center will indicate “READY TO BREW” and the Small
Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a
large mug on the Drip Tray Plate and then press the Large Mug Button.
Brewing Iced Beverages
9. There may be a short pause prior to coffee
being dispensed. The entire brew process
lasts for approximately 1 minute and ends
with a burst of air to remove all liquid from
the K-Cup® pack.
Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Try it by
placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray Assembly
can be removed to accommodate taller cups), choose your favorite K-Cup®
pack and press your preferred cup size. Also, look for the Brew Over Ice™ icon
on K-Cup® packs that are specially crafted to brew over ice! IMPORTANT: Do not
brew into a cup made of glass. Doing so may cause the glass to crack or break.
4. Repeat steps 2 and 3 one more time to completely purge water from
inner tank.
If you are experiencing any problems with your Brewer, please contact
Customer Service at 1.866.901.BREW (2739).
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
c. After setting the desired Auto Off time, press
the Menu Button four times to scroll through
the remaining programming options and exit
the programming mode. “AUTO OFF SET”
(fig. 11) will now be indicated to confirm that
it has been set.
e. If you want to set an “OFF TIME,” repeat the
procedure above in steps b & c to set your
desired “OFF TIME.”
fig.
fig.
13
11
SECTION 2 Controls & Indicators (LCD Control Center)
f. To complete the process, press the Menu Button
two more times to exit the programming mode.
The LCD Control Center will indicate the options
you have set.
Setting the Clock
Programming On/Off Features
READY
TO BREW
AUTO OFF SET
CLOCK
AUTO OFF
SET
OFF TIME
BREW TEMP
Setting the clock is optional. When the clock is set, the time will appear in
the LCD Control Center. NOTE: You must set the clock if you will be using the
On/Off Time programming feature.
The Brewer provides three modes so that you can enjoy gourmet coffee, tea
or hot cocoa on your own schedule. By programming your Brewer to turn on
each morning, you will never have to wait for the Brewer to warm up to brew
a gourmet cup of coffee.
AM
PM
d. To cancel the Auto Off feature, press the
Menu Button twice to reach the Auto Off
programming mode. Press and release the
Small Cup Button under the blinking “H”
to advance one hour at a time until “OFF”
is indicated.
:
11 56
AM
MENU
MENU
g. The On Time and Off Time functions operate
independently from one another. To cancel
either set function, follow the steps above and
use the “H” and “M” buttons to advance to 12:00
AM. Make sure the M button is set to :00, then
change the “H” button. When you reach 12:00
AM, the Control Center will indicate “OFF” and
the function will be disabled.
1. Press the Menu Button.
fig.
9
1. Leave it ON all the time. The Brewer can be left on all the time so that it is
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn
the Brewer off at any time, simply press the Power Button. (NOTE Although
the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.)
Press the Power Button again to restore power to the Brewer. You will have
to wait for the water to heat up before the Brewer is ready to brew.
2. The word “OFF” will appear at the bottom
of the LCD Control Center to indicate that
the clock is not set. The programming
options will appear on the LCD Control
Center with a small arrow pointing to “SET
CLOCK” (fig. 9). “H” (Hour) and “M” (Minute)
will appear and blink.
:
3. Program your Brewer for a specific On/Off Time. NOTE: To use this
programming feature, the clock must be set to the correct time. The clock
will not be displayed unless the time is set.
SET CLOCK
fig.
14
AUTO OFF
ON OFF TIME
BREW TEMP
MENU
2. Set the Brewer to Auto Off following a
:
a. After setting the correct time (required), press
EXAMPLE If you chose to set the On Time at
fig.
Menu
12
specified period of time after the last brew.
the Menu Button three times to program the On
Time feature. The LCD Control Center will show
the programming options with a small arrow
next to “SET ON TIME” (fig. 12).
6:15 AM and the Off Time for 10:00 PM, then the
Brewer will be “READY TO BREW” and maintain
hot water in the tank during that time so that it is
always ready for you to brew. If you wanted to
brew outside this window, simply press the Power
Button and you can brew as soon as the water is
heated and the “READY TO BREW” is indicated on
the LCD Control Center.
READY
fig.
3. Press or hold the blue Small Cup Button under
the blinking “H” until you have reached the
appropriate hour. If the hour has passed 12,
the indicator switches from “AM” to “PM.”
10
TO BREW
a. Press the Menu Button twice to program the
Auto Off feature. The LCD Control Center will
display the programming options with a small
arrow next to “SET AUTO OFF” (fig. 10).
AUTO OFF SET
ON TIME SET
:
11 56
AM
MENU
CLOCK
Set
Hours
Set
Minutes
AUTO OFF
SET ON
TIME
b. Press or hold the blue Small Cup Button under
the “H” to scroll through the hours to your
desired “ON TIME” hour.
4. Press or hold the blue Large Mug Button under
BREW TEMP
CLOCK
SET AUTO OFF
AM
PM
b. Press or hold the blue Small Cup Button
under the blinking “H” to advance 1 hour at
a time, up to 9 hours.
ON OFF TIME
BREW TEMP
:
the blinking “M” to set the minutes.
11 56
MENU
5. When you have reached the correct time, press the Menu Button five
times to scroll through the remaining programming options and exit
the programming mode.
MENU
c. Press or hold the blue Large Mug Button under
the “M” to scroll through the minutes to your
desired “ON TIME” minutes.
:
NOTE The “AUTO OFF” Timer and the On/Off Time programming options
operate independently but can also be programmed to work together. For example,
you can set the On Time function to turn on at 7:00 AM and then set the Auto Off
Timer function to turn off the Brewer two hours after the last brew (fig. 14).
Menu
x2
6. The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power
is lost, follow the procedure above to reset the time as the clock will not be
visible until the time is set.
d. After setting the desired time, press the Menu Button to save the
“ON TIME” and move to the “SET OFF TIME” (fig. 13).
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Cleaning the Funnel—The Funnel can be
removed from the K-Cup® Pack Holder by
pulling on it until it snaps off (fig. 17). The Funnel
is dishwasher safe. To replace it, just snap it
back onto the K-Cup® Pack Holder Assembly.
1. Rinse the filter screen with the strong force of water from your faucet.
2. If you have a sprayer, aim the water spray at the filter screen.
3. Fill the Water Reservoir with approximately two inches of clean water
and agitate (shake) the Water Reservoir.
fig.
17
SECTION 2 Controls & Indicators (LCD Control Center)
SECTION 3 Cleaning & Maintenance
Cleaning External Parts
Programming Brew Temperature (187°–192º F)
Empty the Water Reservoir then fill it with clean water and return it to the Brewer.
If needed, repeat above procedures. CAUTION: Please rinse the Water Reservoir
thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions
remain as they may contaminate the water supply in the Brewer.
The Brewer brews at a preset temperature of 192°. You can adjust this
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea
or hot cocoa. Simply follow the instructions below.
Regular cleaning of the Brewer’s external components is recommended.
3. Cleaning the Exit Needle—The Exit Needle is
located on the inside bottom of the K-Cup® Pack
Holder Assembly. Should a clog arise due to
coffee grinds, it can be cleaned using a paper
clip or similar tool. Remove K-Cup® Pack Holder
Assembly and detach Funnel. Insert the paper
clip (fig. 17) into the Exit Needle to loosen the
clog and push it out. The K-Cup® Pack Holder is
dishwasher safe. CAUTION: There are sharp
1. Never immerse the Brewer in water or other liquids. The Housing and
other external components may be cleaned with a soapy, damp,
non-abrasive cloth.
1. Press the Menu Button on the LCD Control Center five times to
program the Brew Temperature feature.
!
2. The Drip Tray can accumulate up to 8 oz. of overflow. The Drip Tray
and Drip Tray Plate should be periodically inspected and rinsed clean.
To remove the Drip Tray Assembly, simply slide it toward you, keeping
it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate
should not be placed in the dishwasher. They should be cleaned with a
damp, soapy, non-abrasive cloth and rinsed thoroughly.
De-Scaling Your Brewer
2. The LCD Control Center will now display the programming options with
a small arrow next to “SET BREW TEMP” (fig. 15). Also, the temperature
192° (initial setting) will be indicated at the bottom of the LCD Control
Center to indicate the current temperature setting.
Mineral content in water varies from place to place. Depending on the
mineral content of the water in your area, calcium deposits or scale may build
up in your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer
performance. De-scaling your Brewer helps maintain the heating element and
other internal parts of the Brewer that come in contact with water.
needles that puncture the K-Cup® pack above the K-Cup® Pack Holder and in
the bottom of the K-Cup® Pack Holder. To avoid risk of injury, do not put your
fingers in the K-Cup® Pack Assembly Housing.
3. A minus sign will appear over the Small Cup Button and/or a plus sign
over the Large Mug Button. Use these buttons to raise or lower the
temperature one degree at a time.
Cleaning the K-Cup® Pack Holder assembly
The Brewer should be de-scaled every 3-6 months
to ensure optimal performance. It is possible for
calcium deposits to build up faster, making it
necessary to de-scale more often.
Cleaning the Water Reservoir & Water Reservoir Lid
4. Once you have reached your desired brew
1. Cleaning the Parts—The K-Cup® Pack Holder
fig.
15
fig.
18
fig.
16
temperature, press the Menu Button once
to exit the programming mode. “BREW TEMP
SET” will be indicated in the LCD Control
Center if you have changed it from 192°.
Assembly can be placed onto the top shelf of a
dishwasher. NOTE: Use low temperature cycles
in the dishwasher. To remove from the Brewer,
open the cover by lifting the Handle. Grasp the
top of the K-Cup® Pack Holder with one hand
while pushing up on the bottom of the K-Cup®
Pack Holder from underneath with the other
until it releases (fig. 16). After cleaning, align the
K-Cup® Pack Holder with the opening using the
two front ribs as a guide, and snap into place
from the top.
The Water Reservoir Lid and Water Reservoir should be periodically
inspected and cleaned.
You should promptly de-scale if “DE-SCALE” is
indicated on the LCD Control Center (fig. 18).
However, even if “DE-SCALE” is not indicated,
you should continue to de-scale your Brewer
every 3-6 months. Properly follow the de-scaling
procedure described on page 14.
The Water Reservoir Lid or Water Reservoir should not be put into the
dishwasher. They should be cleaned with a damp, soapy, non-abrasive
cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir
with a cloth as lint may remain.
CLOCK
AUTO OFF
ON OFF TIME
SET BREW TEMP
5. To change the brew temperature again, repeat
steps 1 through 3 to change the temperature
up or down, remembering that the temperature
can only be between 187° and 192°.
DE-SCALE
AM
:
192°
11 56
MENU
MENU
To clean the filter screen at the base of your Water Reservoir, empty
the Water Reservoir and follow one or all of the following procedures.
NOTE: If you are using a water filter inside the Water Reservoir, remove
it before cleaning.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 Troubleshooting
SECTION 3 Cleaning & Maintenance (continued)
SITUaTION SOLUTION
SITUaTION SOLUTION
De-Scaling Instructions
A. PREPARE
Service
Brewer does not • Plug Brewer into an independent outlet.
have power • Check to be sure that it is plugged in securely.
• Plug into a different outlet.
Brewing a • The Exit Needle may be clogged (refer to page 13).
partial cup • Clean the K-Cup® Pack Holder if necessary and rinse
under faucet (refer to page 12).
Beyond these recommended cleaning and maintenance procedures, this
Brewer is not user serviceable. For service, please refer to the Warranty
section of this guide.
Step 1: To begin, you will need the following:
At least 48 oz. of undiluted white vinegar
Access to an empty sink
• Reset your home’s circuit breaker, if necessary.
• Make sure that the Power Button has
been turned on.
• The Water Reservoir may have been removed during
brewing. Replace the Water Reservoir and perform a
cleansing brew without a K-Cup® pack.
A large ceramic mug (do not use a paper cup)
Storage
Step 2: Empty the water from the Water Reservoir.
Step 3: Disable Auto Off features.
• De-scale the Brewer (refer to page 13).
Brewer will • After placing the K-Cup® pack in the K-Cup® Pack Holder,
• If you have repeated the de-scale procedure on
your Brewer two times and it is still only brewing
a partial cup, contact Customer Service at
Empty the Water Reservoir before storing, and take care to ensure that you
store your Brewer in a safe and frost free environment. Please be sure to
store your Brewer in its upright position to avoid water leakage from the inner
tank. If you store the Brewer in a cold environment, you run the risk of water
freezing inside the Brewer and causing damage. When you prepare to use it
after storage, we recommend rinsing the Water Reservoir with fresh water
and running three cleansing brews without a K-Cup® pack.
not brew
make sure the Handle is pushed down securely and the
LCD Control Center indicates “READY TO BREW” with the
three Brew Buttons blinking, then press the Small Cup,
Small Mug or Large Mug Button.
B. FILL AND CLEAN
Step 1: Pour approximately 48 oz. of the vinegar into the Water Reservoir.
1.866.901.BREW (2739).
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.
DO NOT USE A K-CUP® PACK, just press a Brew Button.
Pour the contents of the large mug into the sink.
• If the LCD Control Center indicates “ADD WATER,” add
water to the Water Reservoir or make sure the Water
Reservoir is seated properly in its base.
• If the LCD Control Center indicates “ADD WATER”
even after refilling, contact Customer Service at
1.866.901.BREW (2739).
• The Exit Needle may be clogged (refer to page 13).
• If the LCD Control Center indicates “PRIME” and the
blue light in the Water Reservoir is flashing, see below.
The time is not • The time will not be displayed on the LCD Control
displayed on the
LCD Control Center
Center unless you have set it. To set the clock, follow
the procedure on page 10.
Step 3: Repeat the brew process without a K-Cup® pack until “ADD WATER”
If you plan to move your Brewer to a different location, turn the Brewer
off, unplug it, and empty the Water Reservoir. If your Brewer has been in
an environment below freezing, please be sure to let it warm to room
temperature for at least 2 hours before using.
is indicated.
• If power is interrupted to the Brewer, you will need to
set the clock again using the procedure on page 10.
Step 4: Now let the Brewer stand for at least 4 hours while still on.
Step 5: Discard any residual vinegar and rinse the Water Reservoir thoroughly.
My Brewer shuts • Check to make sure that the Auto Off Timer
C. RINSE
off or turns on
automatically
and/or On/Off Time features have not been set. To
do this, press the Menu Button and scroll through
the programming options. “OFF” should be indicated
for Auto Off Timer and On/Off. If “OFF” is not
indicated, follow directions on page 10 to reset.
Step 1: Ensure the Water Reservoir is filled with fresh water.
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.
Pour the contents of the large mug into the sink.
LCD Control Center • Completely remove the Water Reservoir and
Step 3: Repeat brew process until “ADD WATER” is indicated.
indicates “PRIME”
and the blue light in
the Water Reservoir
is flashing
thoroughly clean (refer to page 13). Ensure the
Water Reservoir is fully filled with water. Return it to
the Brewer and ensure it is seated properly.
• If you have completed the above procedure two times
and this situation persists, contact Customer Service
at 1.866.901.BREW (2739).
Step 4: You may need to perform additional cleansing brews if you notice any
residual taste.
NOTE: If “DE-SCALE” is still indicated after completing the procedure,
repeat the de-scaling procedure above.
If any problems persist, contact Customer Service at 1.866.901.BREW (2739)
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 Warranty
Limited One Year Warranty
Nor does this warranty cover damages caused by use of non Keurig Brewed®
K-Cup® brand packs or accessories, services performed by anyone other
than Keurig or its authorized service providers, use of parts other than
genuine Keurig parts, or external causes such as abuse, misuse,
inappropriate power supply or acts of God.
Keurig, Incorporated warrants that your Brewer will be free of defects in
materials or workmanship under normal home use for one year from the date
of purchase. It is recommended that you fill out and return the warranty card
enclosed with your Brewer so that your purchase information will be stored
in our system. Keurig will, at its option, repair or replace a defective Brewer
without charge upon its receipt of proof of the date of purchase. If a
Other Limitations
replacement Brewer is necessary to service this warranty, the replacement
Brewer may be new or reconditioned. If a replacement Brewer is sent, a new
limited one year warranty will be applied to the replacement Brewer.
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR B60 BREWER, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some
states or provinces do not allow disclaimers of such implied warranties or
limitations on how long an implied warranty lasts, so the above limitation
may not apply to you depending on the state or the province of purchase.
This warranty only applies to Brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
Only the use of Keurig Brewed® K-Cup® brand packs and accessories will
guarantee the proper functioning and lifetime of your Keurig® Brewer. Any
damage to or malfunction of your Brewer resulting from the use of non
Keurig Brewed® K-Cup® brand packs and accessories may not be covered by
this warranty or may result in a service fee if the damage or malfunction is
determined to be caused by such use.
How do you obtain warranty service?
Keurig® Brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.866.901.BREW (2739). Please do not return your
Brewer for servicing without first speaking to Keurig Customer Service to
obtain an Authorization to Return number (ATR). Keurig® Brewers returned
without an ATR number will be returned to the sender without servicing.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|