AUDIO VIDEO SURROUND RECEIVER
VR-804
KRF-V4080D
KRF-V5580D
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual is for some models. Model availability and features
(functions) may differ depending on the country and sales area.
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this model has several operation
modes. These modes enable the remote control to control other audio/video components. In order to
effectively use the remote control it is important to read the operating instructions and obtain a proper
understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations.
B60-5444-00 00 MA (K, P, X, Y)
0311
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Contents
Unpacking
Unpack the unit carefully and make sure that all accessories are present.
Caution : Read the pages marked
safe operation.
carefully to ensure
FM indoor antenna (1)
For KRF-V4080D
AM loop antenna (1)
For VR-804
and KRF-V5580D
Before applying the power ...................................................... 2
Safety precautions ..................................................................... 2
How to use this manual ............................................................. 2
Unpacking .................................................................................. 3
Preparing the remote control..................................................... 4
Channel space swiching ............................................................ 4
Special features ......................................................................... 5
Names and functions of parts ................................................. 6
Main Unit .................................................................................... 6
Remote control unit (RC-R0626) (VR-804/KRF-V5580D) and
(RC-R0625) (KRF-V4080D) ......................................................... 7
For VR-804 and KRF-V5580D
Remote control unit (1)
RC-R0626
Batteries (R6/AA) (2)
For KRF-V4080D
Remote control unit (1)
RC-R0625
Batteries (R6/AA) (2)
Setting up the system........................................ 8
Connecting audio components.......................... 9
Connecting video components........................ 10
Digital connections .......................................... 11
Connecting a DVD player (6-channel input)
(For KRF-V4080D only) .................................... 12
*AC plug adapter (1)
Preparations
Connecting the speakers ................................. 13
Connecting the terminals ................................ 14
Connecting the antennas................................. 14
Connecting the system control ....................... 15
Preparing for surround sound ....................... 16
Speaker settings .............................................. 16
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where
use is necessary.)
If any accessories are missing, or if the unit is damaged or fails to operate,
notify your dealer immediately. If your unit was shipped to you directly,
notify your shipper immediately. Kenwood recommends that you retain
the original carton and packing materials in case you need to move or ship
the unit in the future.
Normal playback.............................................. 18
Preparing for playback ..................................... 18
Listening to a source component .................... 18
Adjusting the sound ......................................... 19
Recording .......................................................... 20
Recording audio (analog sources) ................... 20
Recording video ............................................... 20
Recording audio (digital sources) .................... 20
Listening to radio broadcasts ....................... 21
Tuning radio stations ....................................... 21
Presetting radio stations manually .................. 21
Receiving preset stations ................................ 22
Receiving preset stations in order (P.CALL) ... 22
Ambience effects ............................................. 23
Surround modes .............................................. 23
Surround play ................................................... 25
DVD 6-channel playback (For
Keep this manual handy for future reference.
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
Operations
In regard to contact cleaner
Do not use contact cleaner because it could cause a malfunction. Be
specially careful not to use contact cleaners containing oil, for they
may deform the plastic component.
KRF-V4080D only) ............................................ 26
Convenient functions....................................... 26
Basic remote control operations for other
components....................................................... 28
DVD player operation keys .............................. 28
CASSETTE deck, CD player & MD recorder
Remote
Control
operations ........................................................ 29
Additional
Information
In case of difficulty.......................................... 30
Specifications .................................................. 32
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Preparing the remote control
Channel space switching
(Except for the U.S.A., Canada and Australia)
Loading the batteries
The space between radio channels has been set to the one that
prevails in the area to which the system is shipped. However, if the
current channel space setting does not match the setting in the area
where the system is to be used, for instance when you move from
area 1 or area 2 shown in the following table or vice versa, proper
reception of AM/FM broadcasts cannot be expected. In this case,
change the channel space setting in accordance with your area by
referring to the following table.
1 Remove the cover.
2 Insert the batteries.
CHANNEL
Area
Space Frequency
3 Close the cover.
1
U.S.A., Canada and South
American countries
FM: 100 kHz
AM: 10 kHz
1.
2.
FM: 50 kHz
AM: 9 kHz
2
Other countries
75us
50us
75us
50us
AM 10kHz
FM100kHz
AM 9kHz
FM50kHz
AM 10kHz AM 9kHz
FM100kHz FM50kHz
DE-EMPHASIS
CHANNEL SPACE
• Insert two AA-size (R6) batteries as indicated by the polarity markings.
DE-EMPHASIS
CHANNEL SPACE
Operation
When the STANDBY indicator is lit, the power turns ON when you press
Turn the power OFF by pressing the POWER key before moving the
switch level. Move the switch lever to match your area with a small
screwdriver or other pointed tool, then turn the power ON again.
the POWER
key on the remote control. When the power comes ON,
press the key you want to operate.
Operation range
(Approx.)
Remote sensor
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
6 m
• Power mode.
• Input selector settings.
• Picture output.
• SUBWOOFER ON/OFF.
• SW RE-MIX ON/OFF.
• Distance setting.
POWER
• Speaker ON/OFF.
• Volume level.
• BASS, TREBLE, INPUT level.
• TONE ON/OFF.
• Input mode setting.
• Midnight mode setting.
• PRO LOGIC II mode setting.
• Broadcast band.
Infrared ray system
• LOUDNESS ON/OFF.
• Dimmer level.
• MD/TAPE settings.
• Listen mode setting.
• SP SYSTEM.
• Frequency setting.
• Preset stations.
• Tuning mode.
• ACTIVE EQ mode.
• DSP mode.
• When pressing more than one remote control key successively,
press the keys securely by leaving an interval of 1 second or more
between keys.
• Speaker settings.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
replace both batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before applying the power
Special features
For the U.S.A.
FCC WARNING
True home theater sound
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modification is made.
This model incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
£
Dolby Digital
NOTE:
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides up
to 5.1 channels of independent digital audio for better sound quality and
more powerful presence than conventional Dolby Surround.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not
installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
Dolby PRO LOGIC II
DOLBY PRO LOGIC II, whilst totally compatible with its predecessor
PRO LOGIC, provides greater advantages in surround sound. It allows
user to enjoy the conventional stereo or Dolby Surround with a convincing
“5.1 like” presentation. PRO LOGIC II offers special features for controlling
the overall spatial, dimensionality and frontal sound field imaging. PRO
LOGIC II produces an impressive surround sound from video software
– – Increase the separation between the equipment and this model.
– – Connect the equipment into an outlet on a circuit different from
that to which this model is connected.
marked
and three-dimensional space from music CD.
When listening to music, you will be able to enjoy the experience of sheer
STEREO surround sound.
– – Consult the dealer or an experienced radio / TV technician for
help.
DTS
DTS (Digital Theater System) is a 5.1 channel digital audio format that
provides five full-spectrum channels and one low-frequency (subwoofer)
channel for unprecedented clarity, optimum channel separation and a
(wide) dynamic range.
For the U.S.A.
In the DTS mode, the 5.1 channel digital input from a DTS CD, LD or DVD
disc (carrying the “DTS” marking) can be played in Digital Surround.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical.
DSP surround modes
The DSP (Digital Signal Processor) used for this model incorporates a
variety of high quality adjustable sound fields, like “ARENA”, “JAZZ
CLUB”, THEATER”, STADIUM” and “DISCO”. It is compatible with
almost any kind of program source.
®
As an ENERGY STAR Partner, Kenwood
Corporation has determined that this
®
product meets the ENERGY STAR
guidelines for energy efficiency.This
DVD 6-channel input (For KRF-V4080D only)
If you own a DVD player equipped with 6-channel output, this model
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround sound
systems.
product can save energy. Saving energy
reduces air pollution and lowers utility bills.
ACTIVE EQ
ACTIVE EQ mode will produce a more dynamic sound quality in any
condition. You can enjoy a more impressive sound effect when ACTIVE
EQ is turned on during Dolby Digital and DTS playback.
IR (InfraRed) remote control
In addition to the basic opeations of this model, this IR remote control
supplied can also operate Kenwood cassette deck, MD recorder or CD
player which are connected using the system control cords.
This remote control can also control Kenwood DVD players directly
without using the DVD players’ remote control.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
Main Unit
Frequency display,
Input display,
Preset channel display,
Surround mode display
AUTO DETECT
indicator
DTS indicator
6CH INPUT indicator
Speaker indicator
MUTE indicator
Band indicators
DIGITAL indicator
AUTO indicator
CLIP indicator
A
B
MEMO. indicator
ST. indicator
TONE indicator
TUNED indicator
DOLBY DIGITAL
indicator
DSP indicator
Speaker selection indicators
Input channel indicators
Output channel indicators
LOUDNESS indicator
STEREO indicator
PRO LOGIC
indicator
96kHzfs indicator
Display
VOLUME CONTROL
POWER
STANDBY
STANDBY
ON/STANDBY
ON/STANDBY
SPEAKERS ON/OFF
DIMMER
LISTEN MODE
DOWN
UP
ACTIVE EQ
DTS DOLBY DIGITAL
MULTI CONTROL
INPUT SELECTOR
POWER
SOUND
SETUP
MUTE
ON
OFF
ACTIVE EQ INPUT MODE
BAND
AUTO
MEMORY
PHONES
For VR-804
1 POWER ON/OFF key
(For KRF-V4080D/V5580D)
Use to turn the main power ON/OFF.
2 ON/STANDBY key
(For KRF-V4080D/V5580D)
Use to switch the power ON/STANDBY when
the POWER is turned ON.
STANDBY indicator
2 POWER ON/STANDBY key
(For VR-804)
Use to turn the power ON/STANDBY.
STANDBY indicator
3 DIMMER key
Use to select the REC MODE.
Use to adjust the brightness of the display.
¶
4 LISTEN MODE key
Use to select the listening mode.
^
5 Surround LED (light-emitting diode)
! SPEAKERS ON/OFF key
Use to turn the speakers ON/OFF.
@ ACTIVE EQ key
Use to select ACTIVE EQ setting.
# INPUT MODE key
Use to switch between full auto, digital and
analog inputs.
$ BAND key
Use to select the broadcast band.
% AUTO key
Use to change “TAPE” indication to “MD”.
*
Use to select the auto tuning mode.
^ MEMORY key
Use to store radio stations in the preset
memory.
& SETUP key
Use to select the speakers' settings etc.
* MUTE key
*
(
8
indicators
ACTIVE EQ mode LED indicator
(
Lights when this model is in the ACTIVE EQ
^
mode.
DTS mode LED indicator
∞
Lights when this model is in the DTS mode.
DOLBY DIGITAL mode LED indicator ∞
Lights when this model is in the Dolby Digital
mode.
¡
^
)
6 SOUND key
§
Use to adjust the sound quality and the
ambience effects.
¡
¡
7 MULTI CONTROL knob
Use to control a variety of settings.
8 INPUT SELECTOR knob
Use to select the input sources.
9 VOLUME CONTROL knob
0 PHONES jack
^
*
^
∞
*
(
(
Use for headphone listening.
Use to temporarily mute the sound.
Standby mode
CAUTION
While the standby indicator is lit, a small amount of power is supplied to
the system to back-up the memory. This is called standby mode. Under
the condition, the system can be turned ON by the remote control unit.
The power in this equipment will not be completely cut off from the AC
wall outlet when the main switch is turned OFF.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Names and functions of parts
Remote control unit (RC-R0626) (VR-804/KRF-V5580D) and (RC-R0625) (KRF-V4080D)
POWER
1
2
5
3
6
9
DVD
4
POWER
7
0
8
RECEIVER
+10
DOWN-PAGE-UP
LOUDNESS
RETURN
TOP MENU
MENU
OSD
SETUP
SOUND
LISTEN MODE
P.CALL
P.CALL
MULTI CONTROL
BAND
ENTER
TUNING
A/B+100 AUTO
BASS BOOST DISC SKIP
DVD
MD/TAPE
TONE
DVD/6CH
AUX
CD/DVD
TUNER
(For RC-R0625 only)
DVD
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
If the name of a function is different on
this model and on the remote control,
the name of the remote control key in
this manual is indicated in parentheses.
VOLUME
MUTE
1 Numeric keys
™
7 A/B key
% -PAGE-UP key
If CD or MD is selected as the input source,
these keys function as numeric keys. If tuner
is selected as the input source, these keys
are used to call up station presets.
If TAPE is selected as the input source, this is
A and B deck of a double cassette deck.
+100 key
Use to select the disc number with the multi-
CD player.
Use to operate the DVD component.
^ TOP MENU key
Use to operate the DVD component.
& RETURN key
Use to operate the DVD component.
2 DOWN-PAGE- key
Use to operate the DVD component.
LOUDNESS key
Use to switch the status of LOUDNESS.
3 MENU key
DISC SKIP key
LISTEN MODE key
Use to select the listening mode.
* ENTER key
∞
(
If CD is selected as the input source, this key
functions as the multi-CD player disc skip
key.
Use to operate other components.
Use to operate the DVD component.
SETUP key
Use to select the speakers' settings etc.
4 OSD (On Screen Display) key
Use to operate the DVD component.
SOUND key
Use to adjust the sound quality and ambience
effects.
5 MULTI CONTROL %/fi keys
Use to control a variety of settings.
Use to operate other components.
P.CALL 4/¢ keys
If tuner is selected as the input source, these
keys function as preset channel call keys.
4/¢ keys
If CD or MD is selected as the input source,
these keys function as skip keys.
8 BASS BOOST key
Use to select the maximum adjustment
setting for the low frequency range.
9 Input Selector keys [DVD or DVD/6CH (for
RC-R0625 only), AUX, CD/DVD, TUNER,
MD/TAPE, VIDEO 1, VIDEO 2]
Use to select the input sources.
4 DVD ¢ keys
When in DVD player operations, these keys
function as skip keys.
0 DISC SEL. key
Use to operate other components.
ACTIVE EQ key
Use to select ACTIVE EQ setting.
! MUTE key
Use to temporarily mute the sound.
@ POWER key
(
2 key
^
Use to operate other components.
( BAND key
¡
Use to select the broadcast band.
6 key
§
*
If CD is selected as the input source, this key
functions as the play/pause key.
If MD or TAPE is selected as the input source,
this key functions as the play key.
^
) 8 key
Use to operate other components.
¡ AUTO key
™
¡
(
(
Use to select the auto tuning mode.
7 key
If CD, MD or TAPE is selected as the input
source, this key functions as the stop key.
™ TONE key
(
6 TUNING 1/¡ keys
Use to operate the tuner or selected
component.
If CD, MD or TAPE is selected as the input
source, these keys function as search keys.
¡
Use to turn this model on and off.
# DVD POWER key
Use to turn on the DVD equipment.
$ RECEIVER key
Use to return to the operation of this model.
Use to switch the status of TONE control.
£ VOLUME keys
*
Use to adjust this model volume.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Make connections as shown in the following pages.
When connecting the related system components, be
sure to refer to the instruction manuals supplied with
the components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
Input mode settings
CD/DVD, VIDEO2 and DVD (VR-804/KRF-V5580D only) or DVD/
6CH (KRF-V4080D only) inputs each include jacks for digital audio
input and analog audio input.
After completing connections and turning on this model, follow the
steps below.
INPUT SELECTOR
LISTEN MODE
INPUT MODE
Notes
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or there will be noise
interference.
2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connection
cords without disconnecting the power cord can cause malfunctions
and may damage the unit.
3. Do not connect power cords from components whose power
consumption is larger than what is indicated on the AC outlet at the
rear of this unit.
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2,
DVD (VR-804/KRF-V5580D only) or DVD/6CH (KRF-V4080D
only).
Analog connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an “analog” form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs at each end, red for the right channel and white for the left
channel. These cables are usually packed together with the source unit,
or are available at your local electronics retailer.
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the
In CD/DVD, VIDEO2, DVD (VR-804/KRF-V5580D only) or DVD/
6CH (KRF-V4080D only) play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
3 6CH INPT (DVD/6CH input) (KRF-V4080D only)
4 ANALOG (analog input)
microcomputer by referring to “In case of difficulty”.
º
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD
player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto detect:
In “F-AUTO” (full auto) mode (AUTO DETECT and DIGITAL
indicators light up), this model detects the digital or analog input
signals automatically. Priority is given to digital signal during input
mode selection. This model will select the input mode and listening
mode automatically during playback to match the type of input
signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial
factory setting is full auto.
To keep this model set to the currently selected listening mode, use
the INPUT MODE key to select “D-MANUAL” (digital manual).
However, even when this setting is selected, there may be cases
in which the listening mode is selected automatically to match a
Dolby Digital source signal depending on the combination of listening
mode and source digital.
In D-MANUAL mode, if the audio reproduction stops in the middle
due to change in the input signals, etc, press the LISTEN MODE
key.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting audio components
Shape of AC outlets
U.S.A. and Canada
Australia
SYSTEM CONTROL
jacks
%
+
+
To AC wall outlet
-
-
AUDIO
L
R
REC OUT PLAY IN REC OUT PLAY IN
AUX CD/DVD
MD / TAPE
VIDEO1
IN
OUT
Video component )
IN
OUT
Cassette deck or MD
recorder
OUT
CD or DVD player
Other component
OUT
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting video components
+
+
-
-
AUDIO
VIDEO
For VR-804/
KRF-V5580D
only
DVD
IN
MONITOR
OUT
VIDEO 2
IN
REC OUT PLAY IN PLAY IN
VIDEO 1 VIDEO 2
DVD
VIDEO 1
IN
VIDEO 1
OUT
VIDEO
IN
Monitor TV
Video inputs
(Yellow RCA pin cords)
Video deck
IN
IN
OUT
OUT
Video inputs and
Audio inputs
and outputs
outputs
(Yellow RCA pin cords)
DVD player or LD player
DVD player or LD player
Audio OUT
Audio OUT
Video OUT
Video OUT
A video component with digital audio outputs should be connected to the VIDEO 2 jacks.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Digital connections
The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD)
format digital signals.
If you have connected any digital components to this model, be sure to read the “Input mode settings” section carefully.
8
+
+
-
-
COAXIAL
VIDEO 2
OPTICAL
CD / DVD
DVD
DIGITAL IN
OPTICAL DIGITAL OUT (AUDIO)
Optical fiber cable
CD or DVD player
COAXIAL DIGITAL OUT
(AUDIO)
Component with DTS,
Dolby Digital, or PCM
COAXIAL DIGITAL OUT
COAXIAL
DIGITAL
OUT
Connect the video signal and analog
audio signals to the VIDEO 2 jacks.
(See “Connecting video components”.)
0
(AUDIO)
RF digital
demodulator
(Commercially
available)
DOLBY DIGITAL RF
OUT (AUDIO)
PCM OUT
LD player
To connect an LD player with a DIGITAL RF OUT, connect the LD player to the RF digital demodulator (Commercially available).
Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of this model.
Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.)
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting a DVD player (6-channel input) (For KRF-V4080D only)
If you have connected a DVD player to this model with digital connection, be sure to read the “Input mode settings” section carefully.
8
+
+
-
-
DVD / 6CH INPUT
CENTER
COAXIAL
VIDEO 2
OPTICAL
CD / DVD
VIDEO
DVD
IN
MONITOR
OUT
VIDEO 2
IN
SUB
DVD/6CH
FRONT SURROUND
WOOFER
DIGITAL IN
VIDEO 1
IN
VIDEO 1
OUT
VIDEO OUT
(Yellow RCA
pin cord)
FRONT
OUT L/R
SURROUND
OUT L/R
SUBWOOFER
OUT
DVD player
CENTER OUT
COAXIAL
DIGITAL
OUT
(AUDIO)
CAUTION
Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard.
• Do not place any object impairing heat radiation onto the top of the unit.
• Leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting the speakers
Front Speakers
Right
Left
Center
Speaker
SURROUND
FRONT
CENTER
+
+
-
-
R
L
GRAY
BLUE
R
L
C
SPEAKERS (8-16Ω)
RED
WHITE
GREEN
VR-804/KRF-V4080D
SPEAKERS (8
+
+
-
-
KRF-V5580D
SURROUND
SUB
WOOFER
SUB WOOFER
PRE OUT
+
VR-804/KRF-V4080D
-
R
L
SW
GRAY BLUE PURPLE
SPEAKERS (8-16Ω)
Powered
Subwoofer
Subwoofer
Right
Left
Surround Speakers
(Be sure to connect both
surround speakers)
To make sure that each speaker has been connected properly, pay attention to the test tone from each speaker.
Refer to “4 Adjust the speaker volume level.”.
&
EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting the terminals
Connecting the antennas
AM loop antenna
1 Strip coating.
2 Push the lever.
The supplied loop antenna is for use indoors. Place it as far as possible
from this model, TV set, speaker cords and power cord, and adjust the
direction for best reception.
AM antenna terminal connections
3 Insert the cord.
4 Return the lever.
1
Push lever.
2
Insert cord.
3
Release lever.
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker
cords are connected with reversed polarity, the sound will be
unnatural with ambiguous acoustic imaging. Be sure to connect the
speakers correctly.
FM indoor antenna
The supplied indoor antenna is for temporary use only. For stable
signal reception we recommend using an outdoor antenna. Disconnect
the indoor antenna when you connect one outdoors.
FM antenna terminal connections
Speaker impedance
KRF-V4080 and
KRF-V5580D
VR-804
After confirming the speaker impedance indications printed on the
rear panel of this model, connect speakers with matching impedance
ratings. Using speakers with a rated impedance other than that
indicated on the rear panel of this model could result in malfunctions
or damage to the speakers or this model.
Insert the connector.
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna into
the room and connect it to the FM 75Ω terminal.
+
+
-
-
ANTENNA
GND
FM
75Ω
AM
Attach to the
stand
FM indoor antenna
VR-804
KRF-V4080D
and KRF-V5580D
FM outdoor antenna
AM loop antenna
Use an antenna
adapter
(Commercially
available)
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the system
Connecting the system control
Connecting system control cords after connecting a KENWOOD
audio component system lets you take advantage of convenient
system control operations.
SYSTEM CONTROL OPERATIONS
Remote Control
Lets you operate this unit with the system remote supplied with the
this model.
This unit is compatible only with the [SL-16] mode. The system
control operation is not available if the unit is connected in the
[XS8], [XS], or [XR] connection mode.
Automatic Operation
When you start playback from a source component, the input selector
on this unit switches to that component automatically.
If your component has the mode select switch, set the connected
components to the [SL16] mode.
SYSTEM CONTROL
Synchronized Recording
Lets you synchronize recording with the start of playback when
recording from CD, MD or analog discs.
SYSTEM CONTROL
cord
Speaker placement
• You may connect the system control cord to either the up or down
jack.
Center speaker
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control
mode.
[SL16]
Receiver
SYSTEM
CONTROL
cord
Subwoofer
Cassette deck
or MD recorder
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
Front
speaker
Listening
position
CD player
Surround
speaker
Record player
Front speakers : Place to the front left and right of the listening
position. Front speakers are required for all surround modes.
Center speaker : Place front and center. This speaker stabilizes the
sound image and helps recreate sound motion. Required for surround
playback.
Surround speakers : Place to the direct left and right, or slightly
behind, the listening position at even heights, approximately 1 meter
above the ears of the listeners. These speakers recreate sound
motion and atmosphere. Required for surround playback.
Subwoofer : Reproduces powerful deep bass sounds.
• In order to take advantage of the system control operations, the
components must be connected to the correct jacks. To use a CD
player it must be connected to the CD jacks. To use a cassette deck
(or MD recorder) it must be connected to the MD/TAPE jacks.
When using more than one CD player (etc.) only the one connected
to the specified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the
[SL16] system control mode. Do not make system connections
with equipment that is not [SL16] compatible.
• Some MD players are not system control compatible. You cannot
make system control connections to this kind of equipment.
• Although the ideal surround system consists of all the speakers
listed above, if you don't have a center speaker or a subwoofer, you
can divide those signals between the available speakers in the
speaker settings steps to obtain the best possible surround
Notes
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]
equipment for system operations. If your equipment consists of
this kind of combination, please do not connect any system control
cords. Even without system control cords, normal operations can
be carried out without affecting performance.
reproduction from the speakers you have available.
^
2. Do not connect system control cords to any components other
than those specified by KENWOOD. It may cause a malfunction
and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the
system control terminals.
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
Speaker settings
1 FULL RANGE : For selected KENWOOD speaker – for
example, KS-207HT, KS-207EX, KS-208HT.
2 2WAY 2SPKR : For selected KENWOOD speaker – for
example, KS-307HT, KS-308HT, KS-308EX.
3 2WAY 3SPKR : For selected KENWOOD speaker – for
example, KS-707EX.
To enable you to obtain optimum enjoyment from this model’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, and Surround speakers) as described below.
POWER ON/STANDBY
(KRF-V4080D/ V5580D)
ON/STANDBY
MULTI CONTROL
(VR-804)
4 OTHERS
: For general speakers.
• The selection of FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKR
should only be used with 5 channels speaker system setting.
• When the setting FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKR
is selected, the procedure skips to step 4.
3 For general speaker setting, use the MULTI CONTROL knob or
keys to select OTHERS and press the SETUP key again.
POWER ON/OFF
(KRF-V4080D/
V5580D)
SETUP
• The Subwoofer setting indication “SUBW ON” appears.
POWER
SETUP
4 Use the MULTI CONTROL knob or keys to select the
appropriate Subwoofer setting.
MULTI
CONTROL
1 SUBW ON : Subwoofer setting mode to this model is ON.
2 SUBW OFF : Subwoofer setting mode to this model is OFF.
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the Front speakers
are automatically set to “FRNT LRG” and the procedure skips to
step 8.
Before step 8, press the SETUP key to accept the setting.
• When Subwoofer output sound is required, select “FRNT NML”.
1Turn on the power to this model by pressing POWER ON/
STANDBY (for VR-804) or POWER ON/OFF and ON/
STANDBY (for KRF-V4080D/V5580D) or POWER key.
5 Press the SETUP key to accept the setting.
• The Front speakers setting indication “FRNT NML” appears.
2Press the SETUP key to enter the SETUP mode and use the
MULTI CONTROL knob or keys for the following displays.
1 SP SETUP
2 TESTTONE
3 DISTANCE
4 EXIT
6 Use the MULTI CONTROL knob or keys to select the
appropriate Front speakers setting.
1 FRNT NML (normal) : Average size Front speakers are
connected to this model.
: Large Front speakers are connected
The flow of the SETUP is as follows;
2 FRNT LRG (large)
to this model.
• For “FRNT LRG” selection, no sound will be heard from
Subwoofer speaker even when it is set to ON. However, if you
select “SW RE-MIX ON” when Subwoofer is selected, you will
be able to hear sound from the Subwoofer.
When in STEREO mode, the sound goes directly to Front
speaker.
SP SETUP
SP System
TESTTONE
DISTANCE
EXIT
Front
Center
AUTO MANUAL
Full Range
L
C
R
L
C
Surround
2Way 2Speaker
7 Press the SETUP key to accept the setting.
• The Center speaker setting indication “CNTR NML” appears.
2Way 3Speaker
Others
SR
SL
SW
R
8 Use the MULTI CONTROL knob or keys to select the appropriate
Center speaker setting.
SR
SL
SW
Subwoofer
Front
Center
If you have selected “LRG” as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
connected to this model.
Surround
2 CNTR LRG (large) : A large Center speaker is connected to
Subwoofer
Re-mix
this model.
3 CNTR OFF
: Center speaker setting mode to this
model is OFF.
3Select a speaker system.
If you have selected “NML” as the Front speakers setting,
1 CNTR NML (normal) : An average size Center speaker is
connected to this model.
1 Select SP SETUP and press the SETUP key again so that the
speaker system indication “SP SYSTEM” scrolls across the
display.
2 CNTR OFF
: Center speaker setting mode to this
model is OFF.
9 Press the SETUP key again to accept the setting.
•The Surround speaker setting indication “SURR NML” appears.
2 Use the MULTI CONTROL knob or keys to select the speaker
system setting.
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for surround sound
0 Use the MULTI CONTROL knob or keys to select the appropriate
3 Press the SETUP key.
Surround speaker setting.
• The test tone is turned off. This model enters the mode for
inputting the distance to the speakers.
If you have selected “LRG” as the Center speaker setting,
1 SURR NML (normal) : Average size Surround speakers are
connected to this model.
2 SURR LRG (large) : Large Surround speakers are connected
to this model.
4 For MANUAL selection, press the SETUP key each time to
select the speaker channel.
5Input the distance to the speakers.
3 SURR OFF
: Surround speaker setting mode to this
model is OFF.
1 Select the DISTANCE from the set up displays and press the
SETUP key again.
If you have selected other than “LRG” as the Center speaker
setting,
2 Measure the distance from the listening position to each of
the speakers.
1 SURR ON : Surround speaker setting mode to this model is
ON.
2 SURR OFF : Surround speaker setting mode to this model is
Jot down the distance to each of the speakers.
OFF.
Distance to Front speakers
Distance to Center speaker
Distance to Surround speakers
: ____ feet (meters)
: ____ feet (meters)
: ____ feet (meters)
! Press the SETUP key again to accept the setting.
• The Subwoofer re-mix setting indication “SW RE-MIX” scrolls
across the display.
3 Use the MULTI CONTROL knob or keys to select the distance
to the Front speakers.
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
• If Subwoofer is turned OFF, Subwoofer re-mix setting is not
visible.
@ Use the MULTI CONTROL knob or keys to select the
appropriate Subwoofer re-mix setting.
• The allowable setting range is 1 to 30 feet (0.3m to 9.0m) ,
adjustable in 1 foot (0.3m) increments.
1 RMX ON : Subwoofer re-mix set mode to this model is ON.
2 RMX OFF : Subwoofer re-mix set mode to this model is OFF.
# Press the SETUP key to accept the setting.
4 Press the SETUP key to accept the settings.
5 Repeat steps 3 and 4 to input the distance for each of the
speakers.
4Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
6 Setup is complete when the EXIT indication appears.
• In step 4 and 5, indications appear only for the selected
channels of the speakers that require adjusting.
1 Press the SETUP key to begin TEST TONE.
• This model enters the speaker volume level adjustment
mode.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
7 Press the SETUP key to exit the SETUP mode.
The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or keys.
Input level adjustment (analog sources only)
1 AUTO
2 MANUAL
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
2 Press the SETUP key again to select either AUTO or MANUAL.
Use the MULTI CONTROL knob or keys to adjust the volume
level of the test tone output from the speaker channel to be
adjusted.
1 Use the INPUT SELECTOR knob to select the source of which the
For AUTO selection, the test tone is heard from the speakers
in the following sequence for 2 seconds each:
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND key repeatedly until the “INPUT” indication
appears.
3 Use the MULTI CONTROL knob or keys to adjust the input level.
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
§
• If any of the speaker is set as OFF during SP SETUP, the TEST
TONE adjustment for the speaker will be skipped.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal playback
Preparing for playback
Listening to a source component
Some preparatory steps are needed before starting playback.
VOLUME CONTROL
INPUT SELECTOR
POWER ON/STANDBY
SPEAKERS
ON/OFF
(KRF-V4080D/ V5580D)
ON/STANDBY
(VR-804)
POWER
ON/OFF
INPUT SELECTOR
AUTO
(KRF-V4080D/
V5580D)
Input
Selector
Turning on this model
1 Turn on the power to the related components.
VOLUME
2 Turn on the power to this model by pressing POWER ON/
STANDBY (for VR-804) or POWER ON/OFF and ON/
STANDBY (for KRF-V4080D/V5580D) key.
Use the INPUT SELECTOR knob or keys to select the source
you want to listen to.
1
Selecting the input mode
The input sources change as shown below:
If you have selected a component connected to the CD/DVD, VIDEO2,
DVD (VR-804/KRF-V5580 only) or DVD/6CH (KRF-V4080D only) jacks,
make sure that the input mode setting is correct for the type of audio
signal to be used.
1 “AUX”
2 “TUNER”
3 “CD/DVD”
4 “TAPE” or “MD”
5 “VIDEO1”
8
6 “VIDEO2”
7 “DVD” or “DVD/6CH” (for KRF-V4080D only)
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the
source to “MD”, follow the steps below:
Start playback from the selected source.
2
3
Use the VOLUME CONTROL knob or VOLUME keys to adjust
the volume.
1 Use the INPUT SELECTOR knob to select “TAPE”.
2 Hold down the AUTO key for more than 2 seconds.
• The source indication changes to “MD”.
• To return to the original indication, repeat procedure 2.
Setting the speaker status
The speaker indicator lights up.
Press the SPEAKERS ON/OFF key to switch the speaker on or off.
EN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal playback
Adjusting the sound
Adjusting the LOUDNESS mode (remote control only)
You can adjust the Loudness function which controls the low volume
settings to maintain the music’s richness. The adjustment can be made
when this model is in the PCM stereo and analog stereo mode.
SPEAKERS ON/OFF
ACTIVE EQ
VOLUME CONTROL
Press the LOUDNESS key to turn the LOUDNESS setting ON.
To cancel
Press the LOUDNESS key again so that the “LOUDNESS” indicator
goes off.
MULTI CONTROL
PHONES
MUTE
Muting the sound
The MUTE key lets you mute the sound of the speakers.
Press the MUTE key.
LOUDNESS
MULTI
CONTROL
ACTIVE EQ
BASS BOOST
MUTE
TONE
VOLUME
To cancel
Press the MUTE key again so that the “MUTE” indicator goes off.
• MUTE ON can also be deactivated by turning the volume control
knob.
Adjusting the TONE (remote control only)
You can adjust the sound quality when the model is in the PCM stereo
and analog stereo mode.
ACTIVE EQ mode
You can enjoy a more impressive sound effect when ACTIVE EQ is
turned ON during Dolby Digital and DTS playback and, when in PCM and
analog stereo mode
1 Press the TONE key to select the TONE mode.
2 Use the MULTI CONTROL knob or keys to select TONE ON/OFF.
Press the ACTIVE EQ key for the following selections;
1 ACTIVE EQ MUSIC : Effective when listening to music.
(The ACTIVE EQ LED indicator lights up.)
2 ACTIVE EQ CINEMA : Effective when watching a movie.
(The ACTIVE EQ LED indicator lights up.)
3 When in TONE ON selection, press the TONE key for the following
displays.
3 ACTIVE EQ TV
: Effective when watching TV.
(The ACTIVE EQ LED indicator lights up.)
: The ACTIVE EQ function is turned OFF.
(The ACTIVE EQ LED indicator goes off.)
BASS : Select this to adjust the low frequency range.
TREB : Select this to adjust the high frequency range.
4 ACTIVE EQ OFF
4 Use the MULTI CONTROL knob or keys to adjust the sound
quality.
• ACTIVE EQ function will not be available when REC MODE, AUTO
TUNING or PRESET MEMORY is ON and during 96kHz LPCM
playback.
Listening with headphones
• The bass and treble levels are adjustable from -10 to +10 in 2 step
increments.
1 Press the SPEAKERS ON/OFF key so that the speaker indicator
goes off.
Make sure the SP indicator is turned OFF.
Once-touch low frequency emphasis (BASS BOOST)
(remote control only)
You can adjust the sound quality when this model is in the PCM stereo
and analog stereo modes.
• If you turn off all of the speakers when in surround mode, the
surround mode will be canceled as well, resulting in stereo playback.
Press the BASS BOOST key.
• Press the key once to select the maximum (+10) low frequency
emphasis setting.
2 Connect headphones to the PHONES jack.
• TONE will automatically be turned ON.
PHONES
• This key does not function when this model is in the sound quality
or ambience effects adjustment mode.
Switching back the previous setting
Press the BASS BOOST key again.
£~¶
3 Use the VOLUME CONTROL knob or VOLUME keys to adjust the
volume.
EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Recording audio (analog sources)
3 Press and hold the DIMMER key for more than 2 seconds to select
the A-REC or M-REC mode during digital input.
1 Rec mode off : The digital input record mode is switched off.
2 A-REC mode : The digital input signals (DTS, Dolby Digital,
or PCM) are identified automatically and
converted into stereo signals that are ready
for recording.
3 M-REC mode : The input signal type at the moment this
mode is selected is held throughout this
mode.
INPUT SELECTOR
• When the M-REC mode is selected, the digital input signal is
converted to stereo signals (down-mix). But once the digital signal
is chaned to other signal, no signal is output.
When the A-REC mode is selected, the digital input signal is
converted to stereo signals even if the digital signal is changed.
Recording a music source
1 Use the INPUT SELECTOR knob to select the source (other than
“MD/TAPE”) you want to record.
For A-REC mode:
2 Set the MD or TAPE recorder to record.
3 Start playback, then start recording.
Recording video
1 Use the INPUT SELECTOR knob to select the video source (other
than “VIDEO1”) you want to record.
For M-REC mode:
2 Set the video deck connected to VIDEO 1 to record.
• Select the REC MODE to record a digital input source.
3 Start playback, then start recording.
• Recording may not be normal for some video software. This is due
to the copy guard condition.
º
Recording audio (digital sources)
Switch on the REC mode to record a digital input source.
4 Start playback, then start recording.
Usually use the A-REC (Auto-Record) mode to record audio input
sources. When the digital mode changes during recording in the A-REC
mode, the audio input source may be interrupted momentarily.
• If the audio reproduction stops in the middle due to change in the
input signals, etc., press the DIMMER key.
Recording music in A-REC or M-REC mode
DIMMER
INPUT SELECTOR
1 Use the INPUT SELECTOR knob to select the source [CD/DVD,
DVD (VR-804/KRF-V5580 only) or DVD/6CH (KRF-V4080D only)
or VIDEO2] you want to record.
2 Set the MD or TAPE recorder to record.
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
This model can store up to 40 stations in the memory and recall them by
one-touch operation.
Presetting radio stations manually
Tuning radio stations
MEMORY
MULTI CONTROL
MULTI CONTROL
INPUT SELECTOR
BAND
AUTO
1Tune to the station you want to store.
2Press the MEMORY key while receiving the station.
MULTI
CONTROL
Blinks for 5 seconds
Lights for 5 seconds
TUNING1/¡
BAND
TUNER
AUTO
Proceed to step 3 within 5 seconds.
(If more than 5 seconds elapse, press the MEMORY key again).
1Use the INPUT SELECTOR knob or TUNER key to select the
tuner.
3Use the MULTI CONTROL knob to select one of the station
presets (1 – 40).
2Use the BAND key to select the desired broadcast band.
4Press the MEMORY key again to confirm the setting.
“AM” or “FM” indicator
appears in the display
Each press switches the band
as follows:
1 FM
2 AM
• Repeat steps 1, 2, 3, and 4 to store as many stations as
necessary.
• If you store a station at a previously used preset, the previous station
will be replaced by the new one.
3Use the AUTO key to select the desired tuning method.
Each press switches the tuning method as follows:
1 AUTO lit (auto tuning)
2 AUTO not lit (manual tuning)
“AUTO” indicator lights
up in the display.
• Normally, set to “AUTO” (auto tuning). If the radio waves are weak
and there is a lot of interference, switch to manual tuning. (With
manual tuning, stereo broadcasts will be received in monaural.)
4Use the MULTI CONTROL knob or keys, or TUNING 1/
¡keys to select the station.
“ST.” lights when
Frequency
a broadcast is being
display
received in stereo.
“TUNED” is displayed
when a station is received.
Auto tuning
: The next station is tuned automatically.
Manual tuning : Turn the knob (press the key) to select the
desired station.
EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to radio broadcasts
Receiving preset stations
Receiving preset stations in order (P.CALL)
Numeric keys
P.CALL
4/ ¢
TUNER
TUNER
1Press the TUNER key to select tuner as the source.
1Press the TUNER key to select tuner as the source.
2Enter the number of the preset station you want to receive
(up to “40”).
2Use the P.CALL 4¥¢key to select the desired station.
• Each time you press the key, another preset station is received in
order.
Press the numeric keys in the following order:
Pressing the P.CALL ¢ does the following :
For “15”, press ................................ 0, 5
For “20”, press ................................ 0, 0, )
• If you make a mistake entering a two digit number, press the +10
key repeatedly to return to the original display and start again.
Pressing the P.CALL 4does the following :
Holding down the ¢ or 4 key, lets you skip through the
presets, receiving each preset station at 0.5 second intervals.
EN
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
This model is equipped with listening modes that allow you
to enjoy an enhanced sonic ambience with a variety of video
sources.
In order to obtain the optimum effect from the surround
modes, make sure to input the proper speaker settings
Dolby Digital
The Dolby Digital surround format lets you enjoy up to 5.1 channels
of digital surround sound from Dolby Digital program sources (such
as Laserdisc or DVD software marked
previous Dolby surround, Dolby Digital provides even better sound
quality, greater spatial accuracy, and improved dynamic range.
). Compared with
beforehand.
^
Although a full set of speakers (Front Left, Front Right, Center,
Surround Left, Surround Right and Subwoofer) are required for true
5.1 channel Dolby Digital surround sound, this model lets you enjoy
Dolby Digital (and Dolby Surround) program sources, even if you
connect only the front speakers.
Surround modes
The below speaker placements are for 5.1 channel surround sound
system which are;
Although only Dolby Digital soundtracks incorporate a separate low
frequency channel, connecting a subwoofer will also improve deep
bass performance in the other surround modes.
• Dolby Digital
• Dolby Pro Logic II
• DTS
• DSP
Dolby Digital has a “.1” or LFE channel.
The indication “LFE” appears in the display when a signal is being
input for this channel.
• DVD 6-channel (For KRF-V4080D only)
TV / SCREEN
Dolby PRO LOGIC
II
SW
C
R
Dolby Pro Logic II was designed specifically to provide a new sense
of spatiality, directionality and articulation of sounds from Dolby
Surround encoded sources (such as video and Laserdisc software
L
marked
). This is achieved with an intelligent, built-in
feedback logic design, a matrix surround decoding and the decoding
of stereo, full bandwidth surround outputs. The PRO LOGIC II modes
programmed into this model are “MOVIE”, “MUSIC” and “PRO
LOGIC”. The “MOVIE” mode of the PRO LOGIC II has preset
characteristics to produce a calibrated, high-level surround sound
playback while the “MUSIC” mode has user-adjustable characteristics
to offer the three optional controls, like “Dimension”, “Center
Width” and “Panorama” modes to allow optimization of the
soundfields as desired. The “Dimension” control allows the user to
gradually adjust the soundfield either towards the front or towards
the rear; the “Center Width” control allows various adjustment of the
left-center-right speakers’ balance; the “Panorama” extends the
front stereo image to include the surround speakers for an exciting
“wraparound” effect with side wall imaging.
SL
SR
Note
L
Front Left speaker
Subwoofer
LFE = Low Frequency Effects. This channel delivers separate non-
directional bass signals to the Subwoofer for more dynamic deep
bass sound effects.
SW
C
Center speaker
Front Right speaker
R
SL
SR
Surround Left speaker
Surround Right speaker
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
EN
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
DTS mode
DVD 6-channel mode (For KRF-V4080D only)
The DTS multi-channel audio format is available on CD, LD and DVD
software. DTS is a strictly digital format and cannot be decoded inside
most CD, LD or DVD players. For this reason, if you attempt to listen
to DTS encoded software through the analog output of your new CD,
LD or DVD player, you will experience digital noise in most cases. This
noise can be quite loud if the analog output is connected directly to
a high power amplification system. Proper measures for playing the
digital output as described below should be taken to avoid this
situation. To enjoy DTS Digital Surround playback, an external 5.1
channel DTS Digital Surround decoder system or an amplifier with a
built-in DTS Digital Surround decoder must be connected to the
digital output (S/P DIF, AES/EBU or TosLink) of a CD, LD or DVD
player.
Using a DVD player or the like equipped with six (5.1) output channels
and this model, you can enjoy multi-channel encoded DVD source
material in all its splendor. Since the source signals are digital and
each channel is input independently, the resulting sound quality,
sense of spaciousness, and dynamic range are superb.
The indication “6CH INPUT” appears in the display during DVD 6-
channel mode selection.
All models are incorporated with the DTS decoder.
DTS has a “.1” or LFE channel.
The indication “LFE” appears in the display when a signal is being
input for this channel.
£
DSP mode
The DSP mode lets you add the atmosphere of a live concert or hall to
almost any type of program source. These modes are particularly
effective when used with stereo program sources, like CD, television,
and FM radio. You might enjoy trying the ARENA, JAZZ CLUB, THEATER,
STADIUM or DISCO mode the next time you watch a concert or sporting
event!
What's DSP?
DSP stands for Digital Signal Processor.
The way a sound is heard in an actual environment depends on a
variety of different factors. One of the most important is reverberation
(the act of decaying elements of sound echoing in various places).
The DSP modes produce the feeling of presence by using the DSP to
create reverberation, without spoiling the sound quality of the original
signal.
EN
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
Surround play
The DTS compatible models can reproduce a CD, DVD, or LD carrying the
DTS mark.
DOLBY DIGITAL can be used when playing DVD or LD software bearing
When the DOLBY DIGITAL signal is input:
(The DOLBY DIGITAL, PRO LOGIC, or STEREO indicator lights up.)
the
mark and DOLBY DIGITAL format digital broadcasts (etc.).
1 DOLBY DIGITAL : DOLBY DIGITAL surround.
(The DOLBY DIGITAL LED indicator lights
up.)
DOLBY PRO LOGIC can be used when playing video, DVD, or LD
software bearing the
mark.
2 PL II MOVIE
3 PL II MUSIC
4 PRO LOGIC
5 STEREO
: PRO LOGIC II surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
: PRO LOGIC II surround PRO LOGIC mode.
(The PRO LOGIC indicator lights up.)
: Normal stereo playback.
LISTEN MODE
(The STEREO indicator lights up.)
When you select DOLBY DIGITAL
“DOLBY DIGITAL” will scroll from right to left.
INPUT SELECTOR
LISTEN MODE
INPUT MODE
When the DTS signal is input:
(The DTS LED indicator lights up.)
1 DTS
: DTS surround
Input
Selector
2 STEREO : Normal stereo playback
When the analog signal or the digital signal (except for
DOLBY DIGITAL or DTS signal) is input:
1 PL II MOVIE : PRO LOGIC II surround MOVIE mode.
(The PRO LOGIC indicator lights up.)
Preparations
2 PL II MUSIC: PRO LOGIC II surround MUSIC mode.
(The PRO LOGIC indicator lights up.)
3 PRO LOGIC : PRO LOGIC II surround PRO LOGIC mode.
(The PRO LOGIC indicator lights up.)
• Turn ON related components.
• Complete “Preparing for surround sound” (speaker settings).^
• Use the INPUT SELECTOR to select the component you wish to
play back with surround sound.
• Use the INPUT MODE key to select the input mode (analog or
digital) for the source you wish to playback.
• Noise will be produced when a DTS source is played by selecting the
analog input.
4 ARENA
5 JAZZ CLUB : DSP Surround JAZZ CLUB mode.
6 THEATER : DSP Surround THEATER mode.
7 STADIUM : DSP Surround STADIUM mode.
: DSP Surround ARENA mode.
8
8 DISCO
9 STEREO
: DSP Surround DISCO mode.
: Normal stereo playback.
(The STEREO indicator lights up.)
Start playing the video software.
1
2
• Dolby Digital or DTS signal having more channels than the maximum
number of playback channels available using this model’s current
settings is input, downmixing is performed to match the number of
available channels.
Press the LISTEN MODE key to select the listening mode.
The listening mode settings are stored separately for each input. If the
input mode is set to full auto (“AUTO DETECT” lights), this model
selects the optimal listening mode automatically based on the type of
input signal and the speaker settings.
Adjust the volume.
3
Each press of the LISTEN MODE key switches the setting as
listed.
Notes
• Depending on the type of the signal or speaker setting, some
listening modes cannot be selected.
The listening mode settings are different depending on the type
of input signal.
• When playback is started, the sound may be cut or interrupted
before the input source is confirmed as Dolby Digital.
• To enjoy Dolby Digital surround (as well as all the other listening
modes) from a single component, be sure to use a Dolby Digital
compatible source component.
EN
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
DVD 6-channel playback
(For KRF-V4080D only)
Convenient functions
DIMMER
SOUND
Using a DVD player or the like equipped with six (5.1) output channels and
this model, you can enjoy surround sound playback.
Connecting a DVD player which can decode the surround signal itself is
also acceptable.
MULTI CONTROL
MULTI
SOUND
INPUT SELECTOR
INPUT MODE
CONTROL
DVD/6CH
Adjusting the sound
You can make further adjustments to the sound while listening to
playback in the surround mode.
1 Press the SOUND key until the desired item appears in the
display.
Preparations
Each time you press the button, the menu changes as follows:
Note that some items are not displayed in certain modes.
• Connect your DVD player to the DVD/6CH jacks of this model.
• Turn on all other components that will be used.
• Complete “Preparing for surround sound”.
^
1 C (Center speaker level adjustment)*
2 SR (Surround Right speaker level adjustment)*
3 SL (Surround Left speaker level adjustment)*
4 SW (Subwoofer level adjustment)*
Select “DVD/6CH” as the input source.
1
2
3
4
5 INPUT (input level adjustment - analog mode only)
&
6 NIGHT (midnight mode ON/OFF - Dolby Digital mode only)
7 PANORAMA (panorama mode ON/OFF)**
8 DIMENSION (dimension adjustment)**
Select "6CH INPT" by pressing the INPUT MODE key.
Start playback of the DVD software.
Adjust the volume.
9 CENTER WIDTH (center width adjustment)**
*The adjustment is only temporary for the current input selection.
The value will return automatically to the original setup value
when the power is turned on/off or when the input selection is
changed.
** Pro Logic II Music mode only.
2 Use the MULTI CONTROL knob or keys to adjust the setting as
desired.
• It is not possible to adjust the volume level or sound quality (SETUP,
SOUND, LISTEN MODE, ACTIVE EQ and TONE keys will not be
functional) of the channels separately when this model is in the
6CH INPUT mode. Adjust the volume with the controls of the DVD
player.
Midnight mode (Dolby Digital mode only)
For the powered subwoofer, you can adjust the volume of the
subwoofer using the subwoofer’s own volume control.
When watching movies at night, you might not be able to raise the
volume as loud as normal. Midnight mode compresses the dynamic
range of previously specified heavy sound passage of the Dolby Digital
sound track (like scenes with sudden increases in volume) to minimize
the difference in volume between the scenes with heavy sound passage
and scenes with normal sound passage. This makes it easy to hear all of
the sound track, even when listening at low volumes.
1 Press the SOUND key repeatedly until “NIGHT” appears on the
display.
• This can be selected only if CD/DVD, DVD(VR-804/KRF-V5580D
only) or DVD/6CH(KRF-V4080D only), or VIDEO2 is selected as the
source and the listen mode is set to “DOLBY DIGITAL.”
EN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambience effects
2 Use the MULTI CONTROL knob or keys to select the ON or OFF
setting.
Center Width mode (Pro Logic II Music mode only)
Center Width adjustment allows you to enjoy an enhanced sound when
listening to music through center image from only center speaker, or left
and right speakers or various combinations adjustments.
• Some Dolby Digital software may not be compatible with the
Midnight mode.
1 Press the SOUND key repeatedly until “CENTER WIDTH” appears
on the display.
• The CENTER WIDTH indication scrolls across the display.
• When the center speaker is switched OFF, this mode will not
be effective.
Panorama mode (Pro Logic II Music mode only)
When listening to music, you will be able to enjoy the “wraparound”
sound effect when you adjust the panorama mode.
2 Use the MULTI CONTROL knob or keys to adjust the left-center-
right output.
1 Press the SOUND key repeatedly until “PANORAMA” appears on
the display.
Center image will be heard from center speaker only.
• The PANORAMA setting indication scrolls across the display.
“PANORAMA” will be scrolled from right to left.
Center image will be heard from left and right speakers only.
2 Use the MULTI CONTROL knob or keys to select PANORAMA ON
or OFF.
• When in other positions, center image from center speaker, left and
right speakers can be heard simultaneously with various
combinations.
1 ON : PANORAMA mode is ON.
2 OFF : PANORAMA mode is OFF.
Display dimmer adjustment
The dimmer function lets you select the brightness of ths model's
display. You might find this useful if you darken your room to watch
movies or listen to music.
Each time you press the DIMMER key, the display brightness
changes among the three available settings. Select the brightness
level you find most pleasing.
Dimension mode (Pro Logic II Music mode only)
When listening to music with certain recordings, you will also be able to
achieve a suitable balance from all the speakers by adjusting the
dimension mode.
1 Press the SOUND key repeatedly until “DIMENSION” appears on
the display.
• The DIMENSION indication scrolls across the display.
2 Use the MULTI CONTROL knob or keys to adjust the soundfield
towards the rear or the front.
Soundfield is adjusted towards the front.
Soundfield is in neutral position.
96kHz LPCM playback
This model is compatible with the 96kHz LPCM playback. To play a 96kHz
DVD, set the listen mode to “STEREO”.
• In F-AUTO input mode, the listen mode will automatically be STEREO.
• When in D-MANUAL input mode (listen mode is not STEREO), “FS
96kHz” will appear in the display and no sound can be heard from the
speakers.
Soundfield is adjusted towards the rear.
Press the LISTEN MODE key (the listen mode changes to the STEREO
mode) to output sound from the speakers.
EN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic remote control operations for other components
DVD player operation keys
The remote control of this unit can control two groups of KENWOOD DVD players directly without using the remote control supplied with the DVD player.
Group-1 : DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900,
DV5700, DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,
DVF-3060, DVF-3060K, DV-705, DVF-R5070, DVF-3070, DVF-3080, DVF-N7080 and DVF-8100.
Group-2 : DV-4050, DV-303, DVF-R6030, DVF-K5020, DVF-5020, DVF-3020 and DVF-3030.
Depending on your KENWOOD DVD player, you need to set up your receiver remote control as follows:
To set for Group-1 DVD players:
Press the numeric “1” key while pressing the “POWER ” key (not the DVD POWER key) on your remote control.
To set for Group-2 DVD players:
Press the numeric “2” key while pressing the “POWER ” key (not the DVD POWER key) on your remote control.
• If your DVD player is not listed in the list above, perform the set up for either Group-1 or Group-2. When the set up is successful, then your DVD
player falls into that particular group.
How to operate the DVD player with the remote control
1. Pressing the DVD POWER key for more than 2 seconds turns the DVD player on or off.
2. To carry out the functions of the DVD player, first press the DVD POWER key, then press each key for each operation as explained in the DVD
operation pages in the operating instructions. In this case, the DVD operation mode is retained for 15 seconds after pressing any of those DVD
operation buttons.
(To turn the receiver operation mode within 15 seconds, press the RECEIVER key.)
DVD player operation keys
You can perform these basic operations using the keys described below when connected to KENWOOD DVD player.
POWER
1
2
5
3
6
9
POWER
DVD POWER
DVD
4
RECEIVER
(Receiver mode)
Numeric keys
(Select tracks)
POWER
7
0
8
DOWN-PAGE-UP
(Page up or down)
RECEIVER
+10
OSD
DOWN-PAGE-UP
LOUDNESS
TOP MENU
RETURN
OSD (OSD menu)
TOP MENU
(Title)
MENU
MENU
SETUP
SOUND LISTEN MODE
RETURN
%(Cursor »)
fi(Cursor «)
#(Cursor \)
@(Cursor |)
P.CALL
P.CALL
MULTI CONTROL
ENTER (Enter)
BAND
ENTER
TUNING
6 (3 Play)
8 (Pause)
A/B+100 AUTO
1 (Search)
¡ (Search)
BASS BOOST DISC SKIP
DVD
MD/TAPE
TONE
DVD/6CH
AUX
CD/DVD
TUNER
(For RC-R0625 only)
DVD
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
7 (Stop)
VOLUME
MUTE
EN
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic remote control operations for other components
CASSETTE deck, CD player & MD recorder operations
You can perform these basic operations using the keys described below when connected to KENWOOD cassette deck, MD recorder or CD player
equipped with system control operations.
%
Cassette deck operations’ keys
CD player operations’ keys
POWER
POWER
1
2
5
3
6
9
1
2
5
3
6
9
DVD
DVD
4
4
Numeric keys
(Select tracks)
POWER
POWER
7
0
8
7
0
8
RECEIVER
RECEIVER
+10
OSD
+10
OSD
DOWN-PAGE-UP
DOWN-PAGE-UP
LOUDNESS
RETURN
LOUDNESS
TOP MENU
RETURN
TOP MENU
MENU
MENU
SETUP
SOUND LISTEN MODE
SETUP
SOUND LISTEN MODE
P.CALL
P.CALL
P.CALL
P.CALL
4 (Skip down)
¢ (Skip up)
MULTI CONTROL
MULTI CONTROL
2 (Reverse play)
6 (3 Play)
1 (Rewind)
BAND
ENTER
BAND
ENTER
1 (Search)
¡ (Search)
TUNING
TUNING
6 (Play/Pause)
¡ (Fast forward)
A/B+100 AUTO
BASS BOOST DISC SKIP
A/B+100 AUTO
BASS BOOST DISC SKIP
A/B (Cassette
DVD
MD/TAPE
TONE
DVD
MD/TAPE
TONE
deck selection)
DVD/6CH
DVD/6CH
DISC SKIP
AUX
CD/DVD
DVD
TUNER
AUX
CD/DVD
DVD
TUNER
(For RC-R0625 only)
(For RC-R0625 only)
DISC SEL.
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
VIDEO1
VIDEO2 ACTIVE EQ
7 (Stop)
7 (Stop)
VOLUME
VOLUME
MUTE
MUTE
MD recorder operations’ keys
POWER
1
2
5
3
6
9
DVD
4
Numeric keys
(Select tracks)
POWER
7
0
8
RECEIVER
+10
OSD
DOWN-PAGE-UP
LOUDNESS
TOP MENU
RETURN
MENU
SETUP
SOUND LISTEN MODE
P.CALL
P.CALL
4 (Skip down)
¢ (Skip up)
6 (3 Play)
MULTI CONTROL
BAND
ENTER
1 (Search)
¡ (Search)
TUNING
A/B+100 AUTO
BASS BOOST DISC SKIP
DVD
MD/TAPE
TONE
DVD/6CH
+100 (Select tracks)
AUX
CD/DVD
DVD
TUNER
(For RC-R0625 only)
DISC SEL.
VIDEO1
VIDEO2 ACTIVE EQ
7 (Stop)
VOLUME
MUTE
Notes
1. Certain codes may only operate some of the function available on a given model.
2. The pictures above show the typical functions available for each component. Some manufacturers use different key combinations to perform
similar functions. For that reason, we have programmed extra functions on some of the unused number keys to help you control your equipment.
EN
29
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
For the U.S.A. and Canada
Resetting the Microcomputer
Unplug the power cord from the wall outlet, then
plug it back in while holding down the POWER ON/
STANDBY key.
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If
this happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
For other countries
With the power cord plugged in, turn the POWER ON/OFF
key OFF. Then, while holding down the ON/STANDBY
key, press POWER ON/OFF key.
• Please note that resetting the microcomputer will clear the contents
of the memory and return the unit to the state it was in when it left
the factory
Amplifier
Symptom
Remedy
Cause
No sound from the speakers.
• Connect them properly referring to “Connecting
• The speaker cords are disconnected.
the speakers”.
#
• Adjust the volume to a proper level.
• Turn OFF the MUTE.
• Set the SPEAKERS switch to ON.
• VOLUME is set to the minimum position.
• MUTE is ON.
• The SPEAKERS switches are set to OFF.
(
*
• Turn the power off, eliminate the short-
circuiting, then turn on the power again.
The standby indicator blinks and sound is
not output.
• Speaker cords are short-circuited.
• Connect it properly referring to “Connecting
Sound is not output from one of the speakers.
• The speaker cord is disconnected.
• The speaker is not set up correctly.
the speakers”.
• Set it up properly referring to “Speaker
settings”.
#
^
• Connect it properly referring to “Connecting
the speakers”.
• Set it up properly referring to “Speaker
• The surround speaker cords and/or the center
speaker cord is disconnected.
• The speaker is not set up correctly.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very soft.
#
settings”.
^
• Select a surround mode.
• Adjust the speaker levels using the test tone.
&
• A surround mode has not been activated.
• The surround and/or center volume controls
are set to the minimum level.
• Set the input mode to digital manual before
starting playback of the Dolby Digital source.
8
• There are many possible causes for this
problem, depending on the type of DVD player
used.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
• Press the INPUT MODE key to select to full
• The input mode is set to digital manual.
No sound is produced during playback from
a DVD player.
auto mode.
8
• Copy-guarded video software cannot be
recorded.
• The software is copy-guarded.
A video source cannot be recorded normally.
Tuner
Symptom
Cause
Remedy
Radio stations cannot be received.
• No antenna is connected.
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
$
• The broadcast band is not set properly.
• The frequency of the desired station is not
tuned.
¡
• Noise due to ignition of an automobile.
• Install the outdoor antenna away from the
road.
Interference.
• Noise due to interference from an electric
appliance.
• Noise due to a nearby TV set.
• Turn off the power to the appliance.
• Install the receiver farther away from the TV.
• Preset a station with a receivable frequency.
• Preset the station again.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
EN
30
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
Remote control unit
Symptom
Cause
Remedy
Remote control operation is not possible.
• The remote control is set to a different
operation mode.
• Batteries are exhausted.
• Press the source select keys or DVD POWER
keys to select the appropriate operation mode.
• Replace with new batteries.
• The remote control unit is too far away from
the main system, controlling angle is too large,
or there is an obstacle between the receiver
and the remote.
• The audio cords and system control cords are
not connected properly.
• Operate the remote control unit within the
controllable range.
• Connect properly referring to “Setting up the
system”.
• No tape or CD is placed in the source
component.
• An attempt is made to play a tape which is
being recorded in the cassette deck.
• Place the tape or CD in the source component
which you want to play.
• Wait for recording to complete.
EN
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution : Read this page carefully to ensure safe
operation.
Specifications
For the U.S.A and Canada
AUDIO section (VR-804)
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven, at 8Ωfrom
40 Hz to 20 kHz with no more than 0.7% total harmonic distortion. (FTC)
DIGITAL AUDIO section
Sampling frequency 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Effective power output during SURROUND operation
FRONT (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel driven)
............................................................................... 100 W + 100 W
CENTER (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel driven)
.............................................................................................. 100 W
SURROUND (40 ~ 20 kHz, 0.7% T.H.D. at 8Ω one channel
driven) ................................................................... 100 W + 100 W
Total harmonic distortion ........................... 0.05% (1 kHz, 50 W, 8Ω)
Frequency response
Input level / impedance / wave length
Optical ........................... (–15 dBm ~ –21 dBm), 660 nm 30 nm
Coaxial................................................................... 0.5 Vp-p / 75 Ω
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) ................................................. 1 Vp-p / 75 Ω
FM tuner section
CD/DVD ...................................... 20 Hz ~ 70 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
Tuning frequency range................................. 87.5 MHz ~ 108.0 MHz
Usable sensitivity (MONO)
CD/DVD, AUX, TAPE, VIDEO1, VIDEO2 ............................ 95 dB
Input sensitivity / impedance
CD/DVD ................................................................ 550 mV / 47 kΩ
Output level / impedance
TAPE REC ............................................................... 550 mV / 1 kΩ
PRE OUT (SUBWOOFER) (VR-804) ...................... 1.5 V / 2.2 kΩ
Tone control
VR-804
.................1.3 µV (75 Ω)/ 13.2 dBf (75 kHz DEV., SINAD 30 dB)
KRF-V4080D/V5580D
................... 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz DEV., SINAD 30 dB)
50dB quieting sensitivity
STEREO ..................................................... 28 µV (75 Ω)/ 40.2 dBf
Total harmonic distortion (1 kHz)
BASS................................................................ 10 dB (at 100 Hz)
TREBLE ............................................................ 10 dB (at 10 kHz)
Loudness control
MONO.......................................................... 0.5% (71.2 dBf input)
STEREO ....................................................... 0.7% (71.2 dBf input)
Signal to noise ratio (1 kHz, 75 kHz DEV.)
VOLUME at -30dB level ................................... +8 dB (at 100 Hz)
MONO........................................................ 75 dB (71.2 dBf input)
STEREO ..................................................... 68 dB (71.2 dBf input)
Stereo separation (1 kHz) ........................................................... 40 dB
Selectivity ( 400 kHz) VR-804 .................................................... 70 dB
KRF-V4080D/V5580D ............................ 50 dB
For other countries
AUDIO section (KRF-V4080D/V5580D)
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven, at 8Ωfrom
40 Hz to 20 kHz with no more than 0.7% total harmonic distortion. (FTC)
Frequency response .................... (30 Hz ~ 15kHz), +0.5 dB, –3.0 dB
AM tuner section
Effective power output during SURROUND operation
FRONT
Tuning frequency range
10 kHz step (VR-804) .................................. 530 kHz ~ 1,700 kHz
10 kHz step (KRF-V4080D/V5580D) ............... 530 kHz ~ 1,610 kHz
9 kHz step (KRF-V4680D/V5580D) ................. 531 kHz ~ 1,602 kHz
Usable sensitivity (30% mod., S/N 20dB) (VR-804)
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) .... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) ..... 120 W + 120 W
CENTER
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) ................... 100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) .................... 120 W
SURROUND
(1 kHz, 0.7% T.H.D. at 8Ω one channel driven) .... 100 W + 100 W
(1 kHz, 10% T.H.D. at 8Ω one channel driven) ..... 120 W + 120 W
SUBWOOFER (KRF-V5580D)
........................................................................16 µV / (600 µV/m)
Usable sensitivity (KRF-V4080D/V5580D) ............... 16 µV / (600 µV/m)
Signal to noise ratio (30% mod. 1 mV input)........................... 50 dB
GENERAL
Power consumption VR-804 ....................................................... 2.2 A
KRF-V4080D/V5580D .............................. 280W
AC outlet
(80 Hz, 0.7% T.H.D. at 8Ω one channel driven) ................ 100 W
(80 Hz, 10% T.H.D. at 8Ω one channel driven) ................. 120 W
Total harmonic distortion ........................... 0.05% (1 kHz, 50 W, 8Ω)
Frequency response
CD/DVD ...................................... 20 Hz ~ 70 kHz, +0 dB, –3.0 dB
Signal to noise ratio (IHF’66)
CD/DVD, AUX, TAPE, VIDEO1, VIDEO2 ............................ 95 dB
Input sensitivity / impedance
CD/DVD ................................................................ 550 mV / 47 kΩ
DVD/6CH INPUT (KRF-V4080D)........................ 550 mV / 15 kΩ
Output level / impedance
TAPE REC ............................................................... 550 mV / 1 kΩ
PRE OUT (SUBWOOFER) (KRF-V4080D) ............. 1.5 V / 2.2 kΩ
Tone control
SWITCHED
VR-804 ................................................ (total 150 W, 1.25 A max.)
KRF-V4080D/V5580D ...................................... (total 90 W max.)
Dimensions....................................................W : . 440 mm (17-5/16")
H : 143 mm
(5-5/8")
D : 303 mm (11-15/16")
Weight (Net)
VR-804 ................................................................... 7.7 kg (17.0 lb)
KRF-V4080D .......................................................... 7.8 kg (17.2 lb)
KRF-V5580D (for the Australia) .......................... 7.8 kg (17.2 lb)
KRF-V5580D (Except for the Australia) ............. 8.8 kg (19.4 lb)
BASS................................................................ 10 dB (at 100 Hz)
TREBLE ............................................................ 10 dB (at 10 kHz)
Loudness control
VOLUME at -30dB level ................................... +8 dB (at 100 Hz)
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model_____________________ Serial Number_____________________
EN
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|