INSTRUCTION MANUAL
VHF FM TRANSCEIVER
TK-2202
UHF FM TRANSCEIVER
TK-3202
© B62-1762-00 (K,K2,M,M2)
09 08 07 06 05 04 03 02 01 00
Download from Www.Somanuals.com. All Manuals Search And Download.
THANK YOU
We are grateful you chose KENWOOD for your land mobile
radio applications. We believe this easy-to-use transceiver
will provide dependable communications to keep personnel
operating at peak efficiency.
KENWOOD transceivers incorporate the latest in advanced
technology. As a result, we feel strongly that you will be
pleased with the quality and features of this product.
MODELS COVERED BY THIS MANUAL
TK-2202: 8-channel VHF FM Transceiver
TK-3202: 8-channel UHF FM Transceiver
NOTICES TO THE USER
◆
Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆
◆
Illegal operation is punishable by fine or imprisonment or both.
Refer service to qualified technicians only.
Safety: It is important that the operator is aware of, and
understands, hazards common to the operation of any
transceiver.
EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)
Turn off your transceiver while taking on fuel, or while parked in
gasoline service stations.
Download from Www.Somanuals.com. All Manuals Search And Download.
i
One or more of the following statements may be
applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer for technical assistance.
ATTENTION (U.S.A. Only):
The RBRC Recycle seal found on KENWOOD
nickel metal hydride (Ni-MH) battery packs indicates
KENWOOD’s voluntary participation in an industry
program to collect and recycle Ni-MH batteries after
their operating life has expired. The RBRC program
is an alternative to disposing Ni-MH batteries with
your regular refuse or in municipal waste streams,
which is illegal in some areas.
For information on Ni-MH battery recycling in your area, call (toll free)
1-800-8-BATTERY (1-800-822-8837).
KENWOOD’s involvement in this program is part of our commitment
to preserve our environment and conserve our natural resources.
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
PRECAUTIONS
Observe the following precautions to prevent fire, personal
injury, and transceiver damage.
•
•
•
•
Do not modify or attempt to adjust this transceiver for any
reason.
Do not expose the transceiver to long periods of direct
sunlight, nor place it close to heating appliances.
Do not place the transceiver in excessively dusty, humid,
and/or wet areas, nor on unstable surfaces.
If an abnormal odor or smoke is detected coming from the
transceiver, switch OFF the power immediately and
remove the optional battery pack from the transceiver.
Contact your KENWOOD dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
CONTENTS
UNPACKING AND CHECKING EQUIPMENT .......................... 1
SUPPLIED ACCESSORIES ................................................ 1
PREPARATION .......................................................... 3
CHARGING THE Ni-MH BATTERY PACK .................................. 3
INSTALLING/ REMOVING THE BATTERY PACK .............................. 5
INSTALLING THE ANTENNA ............................................... 6
INSTALLING THE BELT CLIP .............................................. 6
INSTALLING THE COVER OVER THE SPEAKER/ MICROPHONE JACKS .......... 7
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET) ......... 7
GETTING ACQUAINTED ................................................ 8
PROGRAMMABLE AUXILIARY FUNCTIONS ......................... 9
BASIC OPERATIONS ................................................. 10
ADVANCED OPERATIONS............................................ 11
AUTODIAL ........................................................... 11
KEY LOCK ........................................................... 11
MONITOR/ SQUELCH OFF ............................................. 12
SCAN ............................................................... 13
SCRAMBLER ......................................................... 15
VOICE OPERATED TRANSMISSION (VOX) ......................... 16
BACKGROUND OPERATIONS ....................................... 18
TIME-OUT TIMER (TOT) ............................................. 18
BUSY CHANNEL LOCKOUT (BCL) ..................................... 18
BATTERY SAVE ....................................................... 18
LOW BATTERY WARNING ............................................. 19
CHANNEL ANNUNCIATION .............................................. 19
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) ....................... 19
STUN ............................................................... 20
DUAL-TONE MULTI-FREQUENCY (DTMF) SIGNALLING .................. 20
FLEETSYNC OPERATION ............................................... 21
BEGINNING/ END OF TRANSMISSION SIGNAL ............................ 21
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the transceiver. We recommend that you
identify the items listed in the following table before discarding
the packing material. If any items are missing or have been
damaged during shipment, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
Item
Part Number Quantity
K, M markets
(TK-2202)
T90-1036-XX
K, M markets
(TK-3202)
Antenna
T90-1039-XX
1
K2, M2 markets
(TK-3202)
T90-1040-XX
W08-0969-XX
W08-0970-XX
Battery charger
1
1
AC adaptor
(K, K2 markets)
AC adaptor
(M, M2 markets)
W08-0971-XX
1
Ni-MH battery pack (KNB-29N)
Speaker/ microphone jack cover
W09-1000-XX
B09-0680-XX
1
1
Speaker/ microphone locking
bracket
J19-5472-XX
1
Belt clip
J29-0713-XX
N99-2043-XX
B62-1762-XX
1
1
1
Screw set
Instruction manual
Note: A market code (K, K2, M, or M2) can be found on the label
attached to the package box.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Antenna: K, M
Antenna: K, M
Antenna: K2, M2
markets (TK-2202) markets (TK-3202) markets (TK-3202)
AC adaptor
(K, K2 markets)
Battery charger
AC adaptor
(M, M2 markets)
Ni-MH battery pack
(KNB-29N)
Speaker/ microphone
jack cover
Speaker/ microphone
locking bracket
Belt clip
Screw set
Download from Www.Somanuals.com. All Manuals Search And Download.
2
PREPARATION
CHARGING THE Ni-MH BATTERY PACK
The battery pack is not charged at the factory; charge it
before use.
The initial charging of the battery pack after purchase or
extended storage (greater than 2 months) will not bring the
battery pack to its normal operating capacity. After repeating
the charge/discharge cycle 2 or 3 times, the operating
capacity will increase to normal.
◆
◆
Do not recharge the battery pack if it is already fully charged.
Doing so may cause the life of the battery pack to shorten or the
battery pack may be damaged.
After recharging the battery pack, disconnect it from the charger.
Charging the battery pack for more than 5 days may reduce the
battery pack life due to overcharging.
Note:
◆
◆
◆
The ambient temperature should be between 32°F and 104°F
(0°C and 40°C) while charging is in progress. Charging outside
this range may not fully charge the battery.
Always switch OFF the transceiver equipped with a Ni-MH
battery pack before charging. Using the transceiver while
charging its battery pack will interfere with correct charging.
The battery pack life is over when its operating time decreases
even though it is fully and correctly charged. Replace the battery
pack.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
1
Plug the AC adaptor cable into
the adaptor jack located on the
rear of the charger.
2
3
Plug the AC adaptor into an AC
outlet.
Slide the Ni-MH battery pack or
transceiver with a NiMH battery
pack into the charger.
•
Make sure the battery pack
terminals are in contact with
the charger terminals by
aligning the grooves of the
battery pack with the tabs of
the charger.
•
The charger LED lights red
and charging begins.
4
When charging is completed, the
indicator lights green. Remove
the battery pack or the transceiver
from the charger.
•
It takes approximately 3 hours
to charge the battery pack.
•
When the charger will not be
used for a long time, unplug
the AC adapter from the AC
outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INSTALLING/ REMOVING THE BATTERY PACK
◆
◆
Do not short the battery terminals or dispose of the battery by
fire.
Never attempt to remove the casing from the battery pack.
1
2
3
Align the battery pack with the
back of the transceiver, then
press the battery pack and
transceiver firmly together
until the release latch on the
base of the transceiver locks.
To remove the battery pack,
lift the safety catch on the
base of the transceiver, then
press the release latch
underneath the safety catch.
While pressing the release
latch, pull the battery pack
away from the transceiver.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
INSTALLING THE ANTENNA
Screw the antenna into the connector
on the top of the transceiver by
holding the antenna at its base and
turning it clockwise until secure.
Antenna
Note: The antenna is neither a handle,
a key ring retainer, nor a speaker/
microphone attachment point. Using the
antenna in these ways may damage the
antenna and degrade your transceiver’s
performance.
INSTALLING THE BELT CLIP
If necessary, attach the belt clip using
the two supplied 3 x 8 mm screws.
Note: If the belt clip is not installed, its
mounting location may get hot during
continuous transmission or when left
sitting in a hot environment.
Belt
clip
Do not use glue which is designed to prevent screw loosening when
installing the belt clip, as it may cause damage to the transceiver.
Acrylic ester, which is contained in these glues, may crack the
transceiver’s back panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
INSTALLING THE COVER OVER THE SPEAKER/ MICROPHONE JACKS
If you are not using a speaker/
microphone, install the cover over the
speaker/ microphone jacks using the
supplied 3 x 6 mm screw.
Note: To keep the transceiver water
resistant, you must cover the speaker/
microphone jacks with the supplied
cover.
Speaker/ microphone
jack cover
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET)
1
Insert the speaker/ microphone
(or headset) plugs into the
speaker/ microphone jacks.
2
Attach the locking bracket using
the supplied 3 x 6 mm screw.
Note: The transceiver is not fully water
resistant while using the speaker/
microphone.
Speaker/ microphone
locking bracket
Download from Www.Somanuals.com. All Manuals Search And Download.
7
GETTING ACQUAINTED
Channel selector
Rotate to select
channels 1 ~ 8.
Antenna
LED indicator
Lights red while
transmitting. Lights
green while receiving
a signal. Flashes
red when the battery
voltage is low while
transmitting.
Power switch/
Volume control
Turn clockwise to
switch ON the
transceiver. To
switch OFF the
transceiver, turn
counterclockwise
until a click sounds.
Rotate to adjust the
volume level.
Speaker
Microphone
PTT (Push-To-
Talk) switch
Press, then
speak into the
microphone to
call a station.
Release to
Speaker/
microphone
jacks
receive.
Side 1 key
Press to activate
its programmable
function (page 9).
Battery pack
(KNB-29N)
Side 2 key
Press to activate
its programmable
function (page 9).
Download from Www.Somanuals.com. All Manuals Search And Download.
8
PROGRAMMABLE AUXILIARY FUNCTIONS
Your dealer can program each of the Side 1 and Side 2 keys
with one of the following auxiliary functions. Refer to their
descriptions, starting on page 11.
•
•
•
•
•
•
•
•
•
•
•
•
Autodial
Key Lock
Key Lock (with Backup)
Monitor
Monitor Momentary
None (No function) (default setting for Side 1 key)
Scan
Scan + Temporary Delete
Scrambler
Squelch Off
Squelch Off Momentary (default setting for Side 2 key)
Temporary Delete
Download from Www.Somanuals.com. All Manuals Search And Download.
9
BASIC OPERATIONS
1
Turn the Power switch/ Volume
control clockwise to switch the
transceiver power ON.
•
A beep sounds if enabled by
your dealer.
2
Press the key programmed with
the Monitor or Squelch Off
function to hear background
noise, then rotate the Power
switch/ Volume control to adjust
the volume.
1
3
4
5
Rotate the Channel selector to
select your desired channel.
•
When you receive an
appropriate signal, you will
hear audio from the speaker.
1
To make a call, press and hold
the PTT switch, then speak into
the microphone using your normal
speaking voice.
•
Hold the microphone
approximately 1.5 inches
(3 to 4 cm) from your lips.
Release the PTT switch to
receive.
Note: When the battery pack voltage
becomes too low, transmission will stop
and an alert tone will sound. See “Low
Battery Warning” on page 19.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
ADVANCED OPERATIONS
The following functions are programmable by your dealer, as
described on page 9.
AUTODIAL
Press and hold the PTT switch, then press the key
programmed as Autodial to transmit the stored DTMF code.
Release the Autodial key, then speak into the microphone
while still pressing the PTT switch to call the other party.
KEY LOCK
Press and hold the key programmed as Key Lock for
1 second to lock/ unlock the transceiver keys. The following
keys/ functions can still be used when Key Lock is active:
Autodial, Key Lock, Monitor, Monitor Momentary, PTT,
Squelch Off, Squelch Off Momentary, and Volume.
If the key is programmed “with backup”, when the transceiver
power is turned OFF and then ON again, the keys remain
locked. Otherwise, when the transceiver power is turned OFF
and then ON again, the Key Lock function will be cancelled.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
MONITOR/ SQUELCH OFF
You can use the key programmed as Monitor or Squelch Off
to listen to weak signals that you cannot hear during normal
operation, to deactivate channel signalling, and to adjust the
volume when no signals are present on your selected
channel.
•
Squelch Off: Momentarily press to hear background
noise. Press the key again to return to normal operation.
•
Squelch Off Momentary: Press and hold to hear
background noise. Release the key to return to normal
operation.
•
•
Monitor: Momentarily press to deactivate QT, DQT,
DTMF, or FleetSync signalling. Press the key again to
return to normal operation.
Monitor Momentary: Press and hold to deactivate QT,
DQT, DTMF, or FleetSync signalling. Release the key to
return to normal operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
SCAN
Scan is useful for monitoring signals on the transceiver
channels. When scanning, the transceiver checks for a signal
on each channel and only stops if a signal is present.
The transceiver will remain on a busy channel until the signal
is no longer present. Your dealer programs the delay time
between signal drop-out and Scan resumption. If a signal is
received during the delay time, the transceiver will remain on
the same channel.
Note: You can only use Scan if your dealer has programmed at least
2 channels and they are not locked out of Scan.
To start scanning, momentarily press the key programmed as
either Scan or Scan + Temporary Delete.
•
Scanning starts from the current channel and ascends
through the channel numbers.
The LED indicator flashes green.
•
•
When a signal is received on a channel and signalling
matches, the LED indicator lights green.
To end Scan, press the Scan or Scan + Temporary Delete
key again.
■ Priority Scan
If enabled, a priority channel is set up one of two ways:
•
Your dealer may set up a fixed priority channel on your
transceiver.
You can select your own priority channel, prior to
•
scanning, using the Channel selector.
During Scan, if a priority channel has been set up on your
transceiver, the transceiver will automatically change to
the priority channel when a call is received on it, even if a
call is being received on a regular channel.
The transceiver will remain on the Priority channel until the
signal drops out. Your dealer programs the delay time
between signal drop-out and scan resumption.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
■ Temporary Delete
If a key is programmed with the Temporary Delete or
Scan + Temporary Delete function, you can temporarily
remove specific channels from the scanning sequence
during Scan. When Scan stops at a channel, you can
remove that channel from the scanning sequence by
pressing and holding the key programmed as Temporary
Delete or Scan + Temporary Delete for 1 second.
•
•
•
You cannot delete the Priority channel, if one has been
set up.
You cannot delete a channel if there will be less than
2 channels available for scanning remaining.
To add the channel back into the Scan list, simply exit
Scan mode or switch the transceiver OFF and then ON
again.
■ Revert Channel
During Scan, pressing the PTT switch to transmit will
cause the transceiver to select the revert channel. Your
dealer can program the revert channel using one of the
following methods:
•
Selected: The last channel selected is assigned as
the new revert channel.
•
Selected + Talkback: If the channel has been
changed during Scan, the newly selected channel is
assigned as the new revert channel. However, the
transceiver also transmits on the channel where Scan
is currently paused.
•
•
Priority: If your dealer has programmed a Priority
channel, it is the revert channel.
Priority + Talkback: If your dealer has programmed a
Priority channel, it is the revert channel. However, the
transceiver also transmits on the channel where Scan
is currently paused.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
SCRAMBLER
Scrambler allows you to hold a conversation in complete
privacy. When activated, any other party listening in on your
channel will be unable to understand your conversation. The
transceiver scrambles your voice so that anybody listening to
your conversation will not be able to understand what you are
saying.
In order for members of your own group to understand your
call while you are using the Scrambler, all other members
must also activate the Scrambler on their transceivers. This
scrambles everybody’s voice while transmitting and
descrambles the voice message on your own transceiver
when you receive the message.
To activate the Scrambler, press the key programmed as
Scrambler.
To deactivate the Scrambler, press the Scrambler key again.
Note: There are 2 options for using the Scrambler. Your dealer can
activate or deactivate the built-in Scrambler function of the
transceiver, or they can add a more secure optional scrambler board
to your transceiver. Ask your dealer for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you to transmit hands-free. This
feature must first be activated by your dealer, and can only be
used if you are using a supported headset.
When operating VOX, you must set a VOX Gain level. This
setting allows the transceiver to recognize sound levels. If the
microphone is too sensitive, it will begin transmitting when
there is noise in the background. If it is not sensitive enough,
it will not pick up your voice when you begin speaking. Be
sure to adjust the VOX Gain level to an appropriate sensitivity
to allow smooth transmission.
To activate VOX and set the VOX Gain level, perform the
following steps:
1
Connect the headset to the
transceiver (page 7).
•
The VOX function does not
activate when a headset is not
connected to the accessory
terminal of the transceiver.
2
3
With the transceiver power OFF,
press and hold the Side 1 key
while turning the transceiver
power ON.
1
Continue to hold the Side 1 key
until a beep sounds.
•
•
The LED indicator lights
orange.
When the Side 1 key is
released, the transceiver
announces the VOX Gain level.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
4
Press the Side 1 key to increase
the VOX Gain level and the
Side 2 key to decrease the level.
•
The VOX Gain can be
adjusted from levels 1 to 10
and OFF.
•
The transceiver announces
the VOX Gain level as you
adjust it. If OFF is selected, a
beep sounds.
5
6
Press the PTT switch to save the
setting.
•
•
A beep will sound.
The transceiver announces
the new VOX Gain level.
Turn the transceiver power OFF
and the ON again to activate
VOX.
Note:
◆
If a speaker/ microphone is connected to the transceiver while
the VOX function is switched ON and the VOX Gain level is
configured to a higher, more sensitive level, louder received
signals may cause the transceiver to start transmission.
◆
When you operate the VOX function, you must use an optional
KHS-1 or KHS-21 accessory.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The purpose of the Time-out Timer is to prevent any caller
from using a channel for an extended period of time.
If you continuously transmit for a period of time that exceeds
the programmed time set by your dealer (default is 1 minute),
the transceiver will stop transmitting and an alert tone will
sound. To stop the tone, release the PTT switch.
Your dealer can program a warning function to alert you
before the TOT expires. Continuously transmitting for the
time specified by your dealer will cause the warning tone to
sound.
BUSY CHANNEL LOCKOUT (BCL)
When activated, BCL prevents you from interfering with other
parties who may be using the same channel that you
selected. Pressing the PTT switch while the channel is in use
will cause your transceiver to emit an alert tone and
transmission will be inhibited (you cannot transmit). Release
the PTT switch to stop the tone and return to receive mode.
Note: Ask your dealer for an explanation on how BCL functions
when using QT, DQT, DTMF, or FleetSync signalling.
BATTERY SAVE
If activated by your dealer, the Battery Save function will
decrease the amount of power used when a signal is not
being received and no operations are being performed (no
keys are being pressed, and no switches are being turned).
While the channel is not busy and no operation is performed
for 5 seconds, Battery Save turns ON. When a signal is
received or an operation is performed, Battery Save turns
OFF.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
LOW BATTERY WARNING
Low Battery Warning alerts you when the battery needs to be
recharged or replaced.
While operating the transceiver, if the battery power becomes
low, an alert tone will sound every 30 seconds and the LED
indicator will blink red. Replace or recharge the battery pack.
CHANNEL ANNUNCIATION
When changing the channel using the Channel selector, an
audio voice will announce the selected channel number, after
you stop changing the channel. (Channel Annunciation can
be activated or deactivated by your dealer.)
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT)
Your dealer may have programmed QT or DQT signalling on
your transceiver channels. A QT tone/DQT code is a sub-
audible tone/code which allows you to ignore (not hear) calls
from other parties who are using the same channel.
When a channel is set up with a QT tone or DQT code,
squelch will only open when a call containing a matching tone
or code is received. Likewise, signals that you transmit will
only be heard by parties whose QT/DQT signalling matches
your transceiver.
If a call containing a different tone or code is made on the
same channel you are using, squelch will not open and you
will not hear the call. This allows you to ignore (not hear)
these calls. Although it may seem like you have your own
private channel while using QT/DQT, other parties can still
hear your calls if they set up their transceiver with the same
tone or code.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
STUN
When the transceiver receives a call containing a stun code,
either transmit mode will be disabled, or both receive mode
and transmit mode will be disabled. (This function is used
when a transceiver is stolen or lost, for example.) Stun is
cancelled when the transceiver receives a call with a stun
reset code.
DUAL-TONE MULT-FREQUENCY (DTMF) SIGNALLING
DTMF Signalling is either enabled or disabled by your dealer.
This function opens the squelch only when the transceiver
receives the DTMF code (3 to 10 digits) programmed in your
transceiver. Each transceiver is normally programmed with a
unique code. You will not hear calls from transceivers that are
not programmed with a matching code.
Your dealer may also program a Group Code in your
transceiver. Ask your dealer for further details.
When you receive a signal containing the correct tones,
squelch opens and you will hear the call.
•
•
The LED indicator momentarily flashes orange.
To mute the speaker after squelch opens, press the key
programmed as Monitor or Monitor Momentary.
•
•
•
Your dealer can program the squelch to close again after a
specific time period elapses.
If Transpond for DTMF Signalling is programmed, an
acknowledgment signal is returned to the calling station.
If Call Alert for DTMF Signalling is programmed, an alert
tone will sound when the correct code is received.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
FLEETSYNC OPERATION
FleetSync is a protocol owned by KENWOOD Corporation
and is enabled or disabled by your dealer. This function
opens the squelch only when the transceiver receives the
Fleet code and ID code programmed in your transceiver.
Calls that do not contain the correct codes will not be heard.
■ Receiving
When you receive a signal containing both your Fleet code
and your ID code, squelch opens and you will hear the
call.
•
•
•
An alert tone will sound.
The LED indicator flashes orange.
To mute the speaker after squelch opens, press the
key programmed as Monitor or Monitor Momentary.
■ Transmitting
To transmit a FleetSync signal, simply press the PTT
switch and make the call. If the selected channel has
been programmed with a FleetSync PTT ID, it will be
transmitted when the call is made.
BEGINNING/ END OF TRANSMISSION SIGNAL
The Beginning of Transmission and End of Transmission
identification signals are used to access and release some
repeaters and telephone systems.
If Beginning of Transmission is set, the ID signal is transmitted
when you press the PTT switch.
If End of Transmission is set, the ID signal is transmitted when
you release the PTT switch.
If both are set, the ID signal is transmitted when you press
and release the PTT switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
|