DVD-RECEIVER
KDV-3241Y
INSTRUCTION MANUAL
© B64-4141-08/00 (E2)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
How to reset your unit
• If the unit fails to operate properly, press RESET
button using a ball point pen or a similar tool.
RESET
Reset button
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
is a trademark of DVD Format/Logo Licensing
Corporation registered in the U.S., Japan and other
countries.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
Manufactured under license under U.S. Patent #: 5,451,942
& other U.S. and worldwide patents issued & pending.
DTS and DTS Digital Out are registered trademarks and the
DTS logos and Symbol are trademarks of DTS, Inc.
© 1996-2007 DTS, Inc. All Rights Reserved.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
DivX, DivX Certified, and associated logos are trademarks
of DivX, Inc. and are used under license.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
TV system selection
You must select the appropriate system mode for
your TV system. When the selected system does not
coincide with the system of your TV, normal colour
picture may not be displayed.
Information on Disposal of Old Electrical
and Electronic Equipment (applicable for
EU countries that have adopted separate
waste collection systems)
• AUTO: Select when the unit is connected with Multi
system TV.
• NTSC: Select when the unit is connected with NTSC-
TV.
Products with the symbol (crossed-out
wheeled bin) cannot be disposed as
household waste.
• PAL: Select when the unit is connected with PAL-TV.
1 Press [SRC] to select the CD/DVD.
Old electrical and electronic equipment
should be recycled at a facility capable
of handling these items and their waste
byproducts. Contact your local authority
for details in locating a recycle facility
nearest to you. Proper recycling and waste
disposal will help conserve resources whilst
preventing detrimental effects on our
health and the environment.
2 Press [0] EJECT.
Confirm that no disc is loaded in the built-in player
(“NO DISC” is displayed).
3 Press and hold [ENTER/ 38] ([8] on the
remote control) for more than 5 seconds.
Each time you press and hold the button for more
than 5 seconds, the TV system switches as follows:
PAL—AUTO—NTSC
The marking of products using lasers
(Except for some areas)
Symbols used in this manual
A section whose title has one of the following
symbols is applicable only to the disc represented by
the symbol.
CLASS 1
LASER PRODUCT
DVD
Video CDs
Audio CDs
DVD
VCD
ACD
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
MP3 MP3 files
WMA files
WMA
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU-representant:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
|
4
KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
About Audio file
Battery installation:
•
Playable Audio file
1. Remove the battery holder with a sharp object such
as a ballpoint pen.
MP3 (.mp3), WMA (.wma)
•
Playable disc file format
2. Install the battery on the battery holder.
3. Install the battery holder back into its original
position.
ISO 9660 Level 1/2, Joliet.
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
:
Folder
Audiofile
CD
(ꢂ)
vꢀ
ꢁ
ꢅ
vꢇ
vꢄ
2WARNING
ꢃ
Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctorimmediately.
vꢆ
ꢈ
vꢉ
v.
2CAUTION
• Use one CR2025 (3 V) lithium battery.
• Remove the battery if the remote control is not used
for a month or longer.
• Do not leave the product in a hot or humid place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic materials.
• In the event of battery leakage, wipe the remote
control completely clean and install a new battery.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public institutions’ rules that apply in your country/
area.
About DivX
DivX is a popular media technology created by DivX,
Inc. DivX media Files contain highly compressed video
with high visual quality that maintains a relatively
small file size. DivX files can also include advanced
media features like menus, subtitles, and alternate
audio tracks. Many DivX media files are available for
download online, and you can create your own using
your personal content and easy-to-use tools from
DivX.com.
About DivX Certified
DivX Certified products are officially tested by the
creators of DivX and guaranteed to play of DivX video,
without DivX 6.
Using the remote control
Point the remote control in the direction of the
control panel to operate.
Certified products qualify for one of several DivX
Profiles that designate the type of video the product
supports, from compact portable video to high-
definition video.
¤
•
Do not store the remote control in high temperatures or
direct sunlight.
•
Do not let the remote control fall onto the floor, where it
may become jammed under the brake or accelerator pedal.
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the
following map.
1
5
2
1
2
1
4
5
2
4
Operation regulatory marks
DVD disc marks
With this DVD, some functions of this unit such as the
play function may be restricted depending on the
location where the DVD is playing. In this case, the
following marks will appear on the screen. For more
information, refer to the disc manual.
Symbol
Description
Indicates a region number. The discs with this mark can
be played with any DVD player.
ALL
Indicates the number of audio languages recorded. Up
to 8 languages can be recorded in a movie. You can
select a favorite language.
Prohibition Mark
8
Indicates the number of subtitled languages recorded.
Up to 32 languages can be recorded.
32
If a DVD disc has scenes shot from multiple angles, you
can select a favorite angle.
9
Indicates the type of screen for the image. The left mark
indicates that a wide image picture (16:9) is displayed
on a standard TV set screen (4:3) with a black band at
both the top and bottom of the screen (letter box).
16:9 LB
|
6
KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
List of playable discs
Handling discs
• Do not touch the recording surface of the disc.
Disc
types
DVD
Standard
Support
Remark
• CD-R/RW, DVD-R/RW, and DVD+R/RW discs are
easier to be damaged than a ordinary music CD.
Use a CD-R/RW, DVD-R/RW, or DVD+R/RW disc after
reading the cautions on the package.
• Do not stick a tape, sticker, etc., on the disc.
Also, do not use a disc with those materials pasted
on it.
‡
×
‡
DVD Video
DVD Audio
DVD-R
MP3/WMA/JPEG/MPEG/
DivX Playback
VR mode/Multi-border/
Multisession/CPRM not
supported
(Playback depends on
authoring conditions)
‡
‡
‡
DVD-RW
DVD+R
Discs that can not be used
DVD+RW
• Discs that are not round cannot be used.
DVD-R DL (Double layer)
DVD+R DL (Double layer)
DVD-RAM
×
×
×
‡
‡
‡
‡
CD
Music CD
CD-ROM
MP3/WMA/JPEG/DivX
playback
Multisession supported
Packet write not supported.
CD-R
• Discs with coloring on the recording surface or that
are dirty cannot be used.
• This unit can only play the CDs with one of
CD-RW
‡
‡
×
DTS-CD
Video CD (VCD)
Super video CD
Photo CD
labels.
Discs without the label may not be played on the
×
unit.
%
CD-EXTRA
Only music CD session can
be played.
• A CD-R or CD-RW that hasn’t been finalized cannot
be played. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
HDCD
×
CCCD
×
×
×
Others
Dualdisc
Super audio CD
Disc storage
• Do not leave discs place them in direct sunlight
(On the seat or dashboard etc.) and where the
temperature is high.
‡: Playback is possible.
%: Playback is partly possible.
× : Playback is impossible.
• Put discs in their cases and store them in such a
storage as disc cabinet.
Use of "DualDisc"
When playing a "DualDisc" on this unit, the surface of
the disc that is not played may be scratched while the
disc is inserted or ejected. Since the music CD surface
does not conform to the CD standard, playback may
be impossible.
(A "DualDisc" is a disc with one surface containing
DVD standard signals and the other surface
containing music CD signals.)
How to eject a disc
When ejecting a disc from this unit, pull it out
horizontally.
If pulled out with a strong downward force, the
recording surface of the disc may be scratched.
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Names and Functions
1
2
3
4
5 6
7
j
i
h
g
f
e
d
c
b
a
0
9 8
• [BAND]
• Selects 3 FM and MW bands.
• Moves to any other file on the disc with various
types of files.
Control panel
¡ [AUDIO/7MENU]
™ VOL/MUTE/[PWR/7OFF]
£ Disc Slot
ª AUX IN
Auxiliary input
º [DISC MENU]
⁄ [DVD SETUP]
¤ [RDM]
¢ Display
∞ [5]/[∞]/[2]/[3]
• Skip/Search [2]/[3]
• Seek/Tune [2]/[3]
• Folder Up/Down [5]/[∞]
• Select [5]/[∞]/[2]/[3]
‹ [REP]
› [SCN]
§ [0] EJECT
fi [ENTER/38]
• Play/Pause [38]
• Enter [ENTER]
¶ FaceplateRelease
Press the Release button.
Releases the faceplate lock so that it can be
removed.
Refer to the following diagram when reattaching
the faceplate.
fl [1] - [6]
Selects a stored radio station frequency.
‡ [EQ/ 7LOUD]
• Equalizer [EQ]
• Loudness [LOUD]
° [SRC]
Selects a source.
· [TI/ PTY]
Traffic Announcement identification (TI)
Program Type (PTY)
¤
•
The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
‚ [DISP]
Accesses On-Screen display.
•
•
Keep the faceplate in its faceplate case while detached.
Do not place the faceplate (and the faceplate case) in areas
exposed to direct sunlight, excessive heat or humidity. Also
avoid places with too much dust or the possibility of water
splashing.
⁄
• 7indicates the button operation (hold) activates
the particular function.
•
To prevent deterioration, do not touch the terminals of the
unit or faceplate with your fingers.
|
8
KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
6
3
4
7
8
9
0
∞ [0- 9]
• Selects numbered items in the menu.
a
• Selects a stored radio station frequency (1 - 6).
5
[REPEAT]
Repeats chapter, track, title or file.
[RANDOM]
Plays tracks or files in random order.
[SCAN]
Plays the first 10 seconds of all track.
[AUDIO]
Selects audio language.
Remote control unit
¡ [PWR]
Switches the unit ON/OFF.
[SUBTITLE]
Selects subtitle language.
[SRC]
Selects a source.
[ANGLE]
Selects a DVD camera angle if available.
[MUTE]
Mutes the volume.
[ZOOM]
Enlarges video image.
™ [4]/[¢] SKIP
[TITLE]
• Goes to the next (previous) chapter, track or file.
• Returns to the beginning of the current chapter,
track, or file.
Displays title menu, if available.
§ [BAND]
• Selects 3 FM and MW bands.
• Moves to any other file on the disc with various
types of files.
[1]/[¡] SCAN/SLOW
Backward (Forward) search playback.
[8] PAUSE
¶ [DISC MENU]/[SETUP]
• Accesses menu on a DVD disc.
• Accesses or removes the Setup menu.
• Pause playback temporarily.
• Press repeatedly for frame-by-frame playback.
[3] PLAY
Starts playback.
• [5]/[∞]/[2]/[3] up/down/left/right
Selects an item in the menu.
[7] STOP
Stops playback.
ª [RETURN]
Displays the menu of a video CD with PBC.
£ [SEARCH]
Selects a track or file.
º [ENTER]
Confirms menu selection.
¢ [DISPLAY]
Accesses On-Screen display.
⁄ [VOL (UP +/ DOWN –)]
Adjusts the volume level.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning the unit on
Selecting a source
1 Press any button ([PWR] on the remote
1 Press [SRC] to select a source.
Press [SRC] repeatedly to switch between the
following sources:
control) other than eject [0] and release.
Tuner—CD/DVD—AUX (AUX IN)
Turning the unit off
1 Press and hold the [OFF] ([PWR] on the remote
control).
Selecting a media type
When you select CD/DVD as a source, you can
switch the MUSIC, PHOTO and MOVIE menu on a
disc with audio, photo, and movie files.
Each menu has a media type indication tab which
shows what media you are selecting.
Inserting a disc
1 Draws the disc, and starts playback
automatically.
1 Press [BAND] ([BAND] on the remote control)
to select other media types.
Media type indication tab
⁄
•
The DVD player plays one, standard 12-cm disc at a time.
Playing back an 8-cm disc is not possible with this unit
and can not use adapter.
•
Do not insert anything other than a disc into the disc
loading slot. Discs which can be played back are listed
on Types of Playable Discs (page 7).
Ejecting a disc
1 Press [0]. The disc automatically ejects from
the loading slot.
⁄
•
For a disc with only audio files, “MUSIC” is displayed. If the
disc has photo or movie files, “PHOTO” tab or “MOVIE” tab
is displayed.
⁄
•
When the disc is ejected by pressing [0] during
playback, it will be loaded automatically after 10 seconds
unless you remove the disc from the unit.
Adjusting the volume
1 Rotate [VOL] (Press [VOL +/–] on the remote
control) to adjust the sound level.
⁄
•
When you turn the unit off, the current volume level is
automatically memorized. Whenever you turn the unit
on again, it will operate at the memorized volume level.
|
10 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Mute
Using the EQ (Equalizer)
1 Press [MUTE] to cut the sound.
2 To cancel it, press [MUTE] again.
1 Press [EQ/LOUD] repeatedly.
The indicator lights in the following order.
POP—CLASSIC—ROCK—JAZZ—VOCAL—
SALSA—SAMBA—USER1—USER2— off (no
display)
• POP: Optimized for R&B, Soul and Country music.
• CLASSIC: Optimized for orchestral music.
• ROCK: Optimized for Hard Rock and Heavy Metal
music.
• JAZZ: Sweet sound with soft feeling.
• VOCAL: Powerful realism with strong sound quality.
• SALSA: Reproduces salsa music acoustics.
• SAMBA: Reproduces samba music acoustics.
• USER1: Use the menu to set the sound level you
want.
Checking the clock
1 You can see the clock pressing [DISP] on the
control panel.
⁄
•
If the RDS broadcasting with CT (Clock Time)
information’s received by the unit, the clock will be
updated automatically in the display. Unless, “NO CLOCK”
appears in the display
• USER2: Use the menu to set the sound level you
want.
⁄
Loudness
•
You can adjust each sound level to your preference.
Once you select a USER mode and then make an
adjustment, it automatically stored for the currently
selected USER mode. Refer to Adjusting the sound level
(page11).
1 Press and hold [EQ/LOUD] to reinforce treble,
bass and surround effect.
Loudness off (no display)—loudness on (“LOUD”
indicator lights)
Adjusting the sound level
1 Press [AUDIO/MENU] repeatedly to select the
mode you want to adjust from volume, bass,
middle, treble, balance and fader.
The indicator lights in the following order.
VOL — BAS— MID — TRB— BAL— FAD
2 Rotate [VOL] (Press [VOL +/–] on the remote
control) to adjust the sound quality.
Indication Turn right
Turn left
“VOL”
“BAS”
“MID”
“TRB”
“BAL”
Increase the volume level. Decrease the volume level.
Increase the bass level. Decrease the bass level.
Increase the middle level. Decrease the middle level.
Increase the treble level. Decrease the treble level.
Decrease the level of the Decrease the level of the right
left speaker(s).
Decrease the level of the Decrease the level of the rear
front speaker(s). speaker(s).
speaker(s).
“FAD”
⁄
•
When EQ or LOUD is set to Off, you can adjustthe sound
level (BAS, MID, TRB) settings.
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
• AUX (Auxiliary) ON/OFF
Changing the general settings
It is possible to use auxiliary equipment with this
unit. Activate the auxiliary setting when using
auxiliary equipment connected to this unit.
AUX ON: When using a auxiliary equipment.
AUX OFF: When not using a auxiliary equipment.
• AUX (Auxiliary) 0 dB/+6 dB
You can adjust the volume level of each source to
prevent radical changes in volume when switching
between sources. You can set to 0dB or +6dB. If
the input level of the connected component is
not high enough, increase the input level properly.
Without adjusting the line input level, you may be
surprised at a loud sound when you change the
source from the external component to another
source.
1 Press and hold [AUDIO/MENU] so that one of
menu items appears.
2 Press [AUDIO/MENU] repeatedly to scroll
between menus.
AF ON—REG ON—TA ALARM—PI SOUND—
AUX ON—AUX 0dB—DEMO OFF—BEEP 2ND
3 Rotate VOL clockwise or counterclockwise to
select one of the settings.
The setting displayed on the display is set and
automatically disappears after about 6 seconds.
• AF (Alternative Frequency) ON/OFF
When the reception quality drops, the tuner
automatically changes to another station in the
network, broadcasting a better reception quality,
using the PI and AF codes.
AF ON: Wherever you drive, you can continue to
listen to the same program without interruptions.
AF OFF: Only station name will be displayed. In
case of poor reception no alternative station can
be used.
• DEMO ON/OFF
You can change the initial indication on the display
to information name (function name, EQ name,
etc...) while listen to a source.
DEMO ON: Displays information name while listen
to source.
DEMO OFF: Cancels the function.
• BEEP 2ND/ALL
• REG (Region) ON/OFF
Sets the beep sound every time a button is
pressed.
BEEP 2ND: The beep is generated when a key is
long pressed (one sec.).
REG ON: The unit switches to another station,
within the same network, broadcasting the same
program when the receiving signals from the
current station become weak.
BEEP ALL: The beep is generated when any key is
pressed.
REG OFF: The unit switches to another station,
within the same network when the receiving
signals from the current station become weak.
(This mode, the program may differ from the one
currently received.)
⁄
•
You can also select one of the settings by pressing
[VOL+/–] on the remote control.
• TA(Traffic Announcement) ALARM/SEEK
TA ALARM: When a newly tuned station has no TP
information for five seconds, a double beep sound
is output.
TA SEEK: When the newly tuned station does not
receive TP information for five seconds, the receiver
retunes to the next station.
• PI (Program Identification) SOUND/MUTE
PI SOUND: If the sound of a station with different
PI is heard intermittently, the receiver mutes the
sound after one second.
PI MUTE: If the sound of a station with different
PI is heard intermittently, the receiver mutes the
sound right now.
|
12 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
Listening to radio stations
Auto search memory
This function lets you automatically store the 6
strongest broadcast frequencies.
1 Press [SRC] to select the tuner.
2 Press [BAND] repeatedly to select a band.
The indicator lights in the following order.
F1 (FM1)—F2 (FM2)—F3 (FM3)— MW (MW)
1 Press [5].
The 6 strongest broadcast frequencies will be
stored under preset buttons 1 to 6 in the order of
their signal strength.
3 Auto Search: Press [2]/[3] ([2]/[3] on the
remote control).
“SEARCH” appears in the display.
2 To cancel, press [5].
When a station is received, searching stops.
4 Manual Search: Press and hold [2]/[3]
([2]/[3] on the remote control) until
“MANUAL” appears, and then press it
repeatedly.
To scan the preset stations
1 Press [∞].
The frequencies move up or down step by step.
Each preset station appears.
⁄
2 To cancel, press [∞].
•
When not operated for 6 seconds after manual search,
the auto search tuner display is shown.
To tune in the preset stations
Storing broadcast frequencies
You can easily store up to 6 broadcast frequencies
for later recall at the touch of a button.
1 Press [BAND] to select the desired band.
2 Press the desired preset buttons [1] to [6].
The preset station of the preset buttons [1] to [6] is
displayed and the preset station is received.
1 Press [BAND] to select desired band you want
to store.
2 Select the desired frequency.
3 Press one of preset buttons [1] to [6] and hold
until the beep sound.
The number you have pressed will be displayed
in the preset number indicator and then remain
lit. The selected radio station frequency has been
stored in memory.
4 Repeat steps 1 to 3 to preset other stations.
The next time, you press the same preset button,
the radio station frequency is recalled from the
memory.
⁄
•
Up to 18 FM stations, 6 for each of 3 FM bands and 6
MW stations can be stored in the memory.
When a new station is stored in the preset station
button, the previously preset station is automatically
erased.
•
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
RDS Operation
RDS display options
TA (Traffic Announcement
identification) function
TA function allows the unit to switch to traffic
annoucement (TA) from the current source (Another
FM station, CD, or other connected components).
In normal RDS operation the display will indicate
the station name. Pressing [DISP] enables you
to cycle through the various data types in the
following sequence:
CT—FREQUENCY—PTY—RT—PS (When PS is
receiving.)
CT—PTY—RT—FREQUENCY (When PS is not
received.)
• CT (Time controlled by the channel)
• PTY (Program type recognition)
• RT (Radio text recognition)
• PS (Program Service name)
1 To switch the TA function on or off, press [TI/
PTY].
⁄
•
If TP (Traffic Program identification) indicator lights up, TA
reception is activated.
•
TA reception will not work if you are listening to an MW
station.
Selecting a media type
To select a certain program type out of the
reception band, the following procedure can be
used.
1 Press and hold [TI/PTY] to select a program
types.
2 After, press and hold [TI/PTY] repeatedly for
selecting each mode.
Music group—Speech group—Search off
3 Press one of preset buttons [1] to [6]
repeatedly.
Each time this button is pressed, the display
mode changes as follows:
No.
1
2
3
4
Music group
POP M — ROCK M
EASY M — LIGHT M
CLASSICS — OTHER M
JAZZ — COUNTRY
NATION M — OLDIES
FOLK M
5
6
No.
1
Speech group
NEWS — AFFAIRS — INFO
2
3
4
5
SPORT — EDUCATE — DRAMA
CULTURE — SCIENCE —VARIED
WEATHER — FINANCE — CHILDREN
SOCIAL — RELIGION — PHONE IN
TRAVEL — LEISURE — DOCUMENT
6
⁄
•
RDS is only available for FM reception.
|
14 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA Operation
MP3/WMA Disc compatibility
with this unit is limited as
follows:
• Sampling Frequency: 8 kHz to 48 kHz (MP3), 22.05
kHz to 48 kHz (WMA)
10
11
12
• Bit rate: 8 kbps to 320 kbps (include VBR) (MP3), 32
kbps to 320 kbps (WMA)
13
• CD-R/CD-RW physical format should be ISO9660.
• If you record MP3/WMA files using software which
cannot create a FILE SYSTEM, it will not be possible
to playback MP3/WMA files. MP3/WMA files are not
compatible with packet write data transfer.
• The total number of files or folders on the disc
should be less than 99 (Audio CD), 3 000 (MP3/
WMA) and 251 (folder).
14
MP3/WMA mode
1. Current track number/Total track number
2. Elapsed time
3. Playback status (Play 3, Pause 8, Scan ¡× 4,
× 8, 1× 4, × 8)
⁄
4. Current mode (Repeat, Intro scan, Random)
5. Previous track name
•
Customers should also note that permission is required
in order to download MP3/WMA files and music from
the Internet. Our company has no right to grant such
permission. Permission should always be sought from
the copyright owner.
6. Album information in CD-TEXT
7. Current track name
8. Title and artist information in CD-TEXT
9. Next track name
10. Previous file name MP3
11. Current folder name MP3
12. Current file name MP3
13. ID3 TAG information MP3
WMA
WMA
WMA
WMA
WMA
Playing an Audio CD MP3/WMA
disc
14. Next file name MP3
⁄
•
The unit can play MP3/WMA formatted recordings.
When a disc contains audio data (CD-DA) and other
format audio data, only the audio data (CD-DA) can be
played back.
If you change the source, CD play also stops (without
ejecting the disc). Next time you select CD as the source,
CD play starts from where playback has been stopped
previously.
• Insert a disc in the unit.
“READING” appears in the display, and playback
starts automatically.
•
1
5
2
3
4
6
7
8
9
AUDIO CD mode
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/MP3/WMA Operation
Pause
Search
When a disc has more than one track/file, you can
move to another track/file as follows:
1 Press [38] ([8] on the remote control) during
playback.
1 Press and hold [2]/[3] ([1]/[¡] on the
remote control) to select the required speed
during playback and then release at the point
you want.
2 To return to playback, press [38] (PLAY [3]
or [8] on the remote control).
⁄
Skip to next track/file
•
Backward search: 1×4, 1×8
•
Forward search: ¡×4, ¡×8
1 Press briefly [3] ([¢] on the remote control)
to select the next track or file.
Intro scan
The first 10 seconds of each tracks/files (SCN) or
each files in the current selected folder (^SCN) on
the disc are are played.
Skip to previous track/file
1 Press briefly [2] ([4] on the remote
control) and press again within 4 seconds of
playing time.
1 Press [SCN].
“SCN”
(or “ ^SCN” MP3
WMA
)
ACD
appears on the display.
• Press and hold [SCN] for about 2 seconds during
playback. MP3
WMA
Return to the beginning of the
current track/file
“SCN” appears on the display.
2 Press [SCN] again.
“SCN” (or “ ^SCN”) disappears from the display and
the intro scan is cancelled.
1 Press briefly [2] ([4] on the remote control)
after 4 seconds of playing time.
Repeat
Moving to another track/file
The current selected tracks/files (RPT) on the disc is
played repeatedly.
When a disc has more than one track/file, you can
move to another track/file as follows:
1 Press [REP] during playback.
“REP” appears on the display.
• Press and hold [REP] for about 2 seconds during
1 Press [SEARCH] on the remote control.
2 Press the appropriate numbered button ([0] to
[9]) to select a track/file number.
playback. MP3
WMA
“RPT” appears on the display.
2 Press [REP] again.
“RPT” disappears from the display and the repeat
mode is cancelled.
|
16 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Random
All of the tracks/files (RDM) or the current selected
folder (^RDM) on the disc is played randomly.
1 Press [RDM] during playback.
“RDM”
(or ” ^RDM” MP3
WMA
)
ACD
appears on the display.
• Press and hold [RDM] for about 2 seconds during
playback. MP3
WMA
“RDM” appears on the display.
2 Press [RDM] again.
“RDM” (or ” ^RDM”) disappears from the display
and the random playback is cancelled.
⁄
•
During random playback, if you press [2] ([4] on
remote control), you won’t go back to the previous track.
CD TEXT/ID3 TAG
When playing a disc containing information,
you can see the CD TEXT/ID3 TAG information.
In a ID3 TAG, information about the file (album
title, performer name, song title) is recorded. In
a WMA content, information about the file (song
title, performer name) is recorded. If there is no
information, “NO TEXT” will be shown in the display.
1 Press [DISP] repeatedly during MP3/WMA/CD
TEXT file playback.
To skip to the next or previous
folder MP3
WMA
1 Press [5] to skip to the next folder, and press
[∞] to skip to the previous folder.
⁄
•
Time display appearing on the display part when playing
VBR file may vary and there may be some difference
from actual time (both progress time and VBR are
displayed at the same time when playing file).
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP Menu
SETUP Menu
Language
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things.
1 Press [DVD SETUP].
The “Setup menu” appears.
You can perform the same operation by pressing
and holding [DISC MENU/SETUP] on the remote
control.
2 Use [5]/[∞] to select the desired option then
press [3] to move to the second level.
The screen shows the current setting for the
selected item as well as alternate setting(s).
Menu Language
Select a language for the setup menu and onscreen
display. If you select a language for the setup menu,
the character set for MP3 tag, DivX subtitle is also
changed according to the language. Refer to Notice
for displaying the DivX subtitle (page 31).
3 Use [5]/[∞] to select the second desired
option then press [3] to move to the third
level.
4 Use [5]/[∞] to select the desired setting then
press [ENTER] to confirm your selection.
Some items require additional steps.
5 Press [DVD SETUP].
Disc Audio/Subtitle/Menu
Select the language you prefer for the audio track
of disc, subtitle, and the disc menu.
The Setup menu ends.
You can perform the same operation by pressing
[DISC MENU/SETUP] or pressing PLAY [3] or
[RETURN] on the remote control.
• Original: Refers to the original language in which
the disc was recorded.
⁄
• Other: To select another language, press
number buttons and then [ENTER] to enter the
corresponding 4-digit number according to the
language code list (page 32). If you enter the
wrong language code, input the 4-digit number
and press any number button. When – – – –
appears on the screen, input the 4-digit number
correctly.
•
Press [2] to go back to the previous level.
• Off: This option is showed only in Disc Subtitle. If
you select Off, disc subtitle is not displayed.
|
18 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Audio
Each DVD disc has a variety of audio output
options. Set the player’s AUDIO options according
to the type of audio system you use.
TV Aspect
• 16:9: Select when a 16:9 wide TV is connected.
• 4:3 Letter Box: Select when a standard 4:3 TV is
connected. Displays a wide picture with bands on
the upper and lower portions of the screen.
• 4:3 Pan Scan: Select when a standard 4:3 TV is
connected. Automatically displays the wide picture
on the entire screen and cuts off the portions that
do not fit.
Dolby Digital/DTS/MPEG
• Bitstream: Select Bitstream if you connect the
Digital optical out jack of this unit to an amplifier or
other equipment with a Dolby Digital, DTS or MPEG
decoder.
• PCM: Select when connected to a 2-channel digital
stereo amplifier. DVDs encoded in Dolby Digital
or MPEG will be automatically downmixed to 2-
channel PCM audio.
⁄
•
In case of DivX file, TV Aspect of 4:3 Letter Box and 4:3
Pan Scan are the same.
• Off (for DTS): If you select Off, the DTS signal is not
output through the optical out jack.
B.L.E. (Black Level Expansion)
To select the black level of playback pictures. Set
your preference and monitor’s ability.
Dynamic Range Control (DRC)
• On: Expanded grey scale.
• Off: Standard grey scale.
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation, thanks to digital audio technology.
However, you may wish to compress the dynamic
range of the audio output (the difference between
the loudest sounds and the quietest ones). This
allows you to listen to a movie at a lower volume
without losing clarity of sound. Set DRC to On for
this effect.
⁄
•
The B.L.E. function works NTSC system only.
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP Menu
Lock (Parental Control)
⁄
•
If you set a rating for the player, all disc scenes with the
To access the Rating, Password and Area Code
features, you must input the 4- digit password you
created. If you have not yet entered a password you
are prompted to do so.
same rating or lower are played. Higher rated scenes
are not played unless an alternate scene is available on
the disc. The alternative must have the same rating or
a lower one. If no suitable alternative is found, playback
stops. You must enter the 4-digit password or change
the rating level in order to play the disc.
Password
You can enter or change password.
To make a new password:
1 Select Password on the Lock menu and then
press [3].
2 Press [ENTER] when the New option is
highlighted.
1 Input a 4-digit code and press [ENTER].
• If you made a mistake before pressing [ENTER],
press [2] to delete the digits one by one.
3 Enter a new password using the number
buttons then press [ENTER].
2 Enter it again and press [ENTER] to verify.
4 Enter the password again to verify.
Rating
To change the password:
Some movies contain scenes that may not be
suitable for children to view. Many of these discs
contain parental control information that applies
to the complete disc or to certain scenes on the
disc. Movies and scenes are rated from 1 to 8,
depending on the country. Some discs offer more
suitable scenes as an alternative. The parental
control feature allows you to block access to scenes
below the rating you input, thereby preventing
your children from being able to view material you
believe is unsuitable.
1 Select Password on the Lock menu and then
press [3].
2 Press [ENTER] when the Change option is
highlighted.
3 Enter a current password using the numbered
buttons then press [ENTER].
4 Enter a new password using the numbered
buttons then press [ENTER].
5 Enter the password again to verify.
1 Select Rating on the Lock menu then press
[3].
If you forget your password
If you forget your password you can clear it using
the following steps.
2 Select a rating from 1 to 8 using the [5]/[∞].
• Rating 1 to 8: Rating one (1) has the most
restrictions and rating eight (8) is the least
restrictive.
• Unlock: If you select Unlock, parental control is not
active and the disc plays in full.
1 Press [DVD SETUP].
The “Setup menu” appears.
• You can perform the same operation by pressing
and holding [DISC MENU/SETUP] on the remote
control.
3 Press [ENTER] to confirm your rating selection.
|
20 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Input the 6-digit number “210499” and the
password is cleared.
Others
3 Enter a new password. Refer to To make a new
password (page 20).
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, according to the
area code. Refer to Area code list (page 33).
1 Select Area Code on the Lock menu then press
[3].
PBC
2 Follow the step 2 as shown on Rating on the
previous page.
Set Playback Control (PBC) to On or Off.
• On: Video CDs with PBC are played according to
the PBC.
• Off: Video CDs with PBC are played in the same
way as Audio CDs.
3 Select the first character using [5]/[∞].
4 Press [ENTER] and select the second character
using [5]/[∞].
5 Press [ENTER] to confirm your country code
selection.
⁄
•
The PBC function is only available for playing the Video
CD 2.0.
DivX VOD
We provide you the DivX VOD (Video On Demand)
registration code that allows you to rent and
purchase videos based on the DivX VOD service. For
1 Select DivX VOD option and then press [3].
2 Press [ENTER] while Show Code is selected and
the registration code will appear.
Use the registration code to purchase or rent the
vod.
3 Press [ENTER] to exit.
⁄
•
All the downloaded videos from DivX VOD can only be
played back on this unit.
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD/VCD Operation
Displaying Disc Information on- Playing a DVD and Video CD
screen
1 Insert a disc in the unit.
You can display various information about the disc
loaded on-screen.
“READING” appears on the display, and
playback starts automatically.
• If playback does not start, press [38] (PLAY [3] on
the remote control).
• In some cases, the disc menu might appear instead.
¡
™
£
⁄
•
•
•
The menu screen may be displayed first after loading a
DVD or Video CD 2.0 which offers a menu.
If any button is not pressed after a disc is ejected, a disc
is loaded automatically in about 10 seconds.
If parental control is set and the disc is not within the
rating settings you must input the password. See Lock
(Parental Control) (page 20).
¢
∞
§
•
DVDs may have a region code. Your player does not play
discs that have a region code different from your player.
About the region code, refer to Region code (page 6).
1. Title: Current title number/total number of titles
2. Chapter (Track): Current chapter (or track)
number/total number of chapters (or tracks)
3. Time: Elapsed playing time
Pre-Stop
1 Press [7] on the remote control during
playback.
4. Audio: Selected audio language or channel
5. Subtitle: Selected subtitle
“PRE-STOP” appears in the display.
6. Angle: Selected angle/total number of angles
2 To return to playback, if you press [38] (PLAY
[3] on the remote control) on the Pre-Stop
mode, it will be played from this point you
stop.
1 Press [DISPLAY] on the remote control during
playback.
The displayed items differ depending on the disc
type or playing status.
2 Press [5]/[∞] to select an item.
3 Press [2]/[3] to change or select the setting.
You can also use 0 to 9 if appropriate.
For some functions, press [ENTER] to execute the
setting.
Stop
1 Press [7] on the Pre-Stop mode.
⁄
2 To return to playback, if you press [38] (PLAY
[3] on the remote control), it will be played
from the beginning of the disc.
•
If any button is not pressed for a few seconds, the on-
screen display disappears.
•
Some discs may not provide all of the features on the
on-screen display example shown above. On a Video CD
2.0 with PBC, PBC will be displayed instead of the track
number. Refer to PBC (page 21).
|
22 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Pause
Moving to another title
When a disc has more than one title, you can move
to another title as follows:
DVD
1 Press [38] ([8] on the remote control) during
playback.
2 To return to playback, press [38] (PLAY [3] on
1 Press DISPLAY on the remote control and then
the remote control).
press [5]/[∞] to select the menu item (title).
2 Press the appropriate numbered button (0 to
9) to select a title number or [2]/[3] button.
Still picture and frame-by-
frame playback
Moving to another chapter/
track
When a title on a disc has more than one chapter
or a disc has more than one track, you can move to
another chapter/track as follows:
1 Press [38] ([8] on the remote control) during
playback.
The unit will now go into the PAUSE mode.
2 You can advance the picture frame-byframe
by pressing [8] on the remote control
repeatedly.
1 Press [2]/[3] ([4]/[¢] on the remote
control) briefly during playback to select
the next chapter/track or to return to the
beginning of the current chapter/track.
3 To return normal playback, press [38] (PLAY
[3] on the remote control).
2 Press [2] ([4] on the remote control) twice
briefly to step back to the previous chapter/
track.
Slow motion
3 To go directly to any chapter during playback,
press [DISPLAY] on the remote control and
press [5]/[∞] to select the chapter/track icon.
Then, input the chapter/ track number or use
[2]/[3].
1 Press [38] ([8] on the remote control) during
playback.
The unit will now go into the PAUSE mode.
2 Use [1]/[¡] on the remote control to select
the required speed:
⁄
1/16,
1/16,
1/8,
1/8,
1/4, or
1/4, or
1/2 (backward), or
1/2 (forward)
•
For 2 digit numbers, press the numbered buttons (0 to 9)
in rapid succession.
With a Video CD, the Slow speed changes:
1/16, 1/8, 1/4 or 1/2 (forward).
•
On a Video CD with PBC, you must set PBC to Off on the
setup menu (page 21).
3 To exit Slow Motion mode, press [38] (PLAY
[3] on the remote control).
⁄
Skip to next chapter/track
•
Slow motion playback in reverse is not possible with
Video CDs.
1 Press briefly [3] ([¢] on the remote control)
to select the next chapter or track.
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD/VCD Operation
Skip to previous chapter/track
- Track/All The default settings is All.
VCD
1 To repeat the track currently playing, press
[REP] ([REPEAT] on the remote control).
The Track icon appears on the TV screen.
1 Press briefly [2] ([4] on the remote control)
and press again within 4 seconds of playing
time.
2 To exit the repeat mode, press [REP] ([REPEAT]
on the remote control) again.
The All icon appears on the TV screen.
Return to the beginning of the
current chapter/track
⁄
•
On a Video CD with PBC, you must set PBC to Off on the
setup menu (page 21).
1 Press briefly [2] ([4] on the remote control)
after 4 seconds of playing time.
Time search
The Time Search function allows you to start playing
at any chosen time on the disc.
Scan
1 Press [1]/[¡] on the remote control during
1 Press [DISPLAY] on the remote control during
playback.
playback.
2 Press [1]/[¡] repeatedly on the remote
control to select the required speed:
1×2, 1×4, 1×8, 1×16, 1×32, 1×100
(backward) or ¡×2, ¡×4, ¡×8, ¡×16,
¡×32, ¡×100 (forward)
With a Video CD, the scan speed changes: 1×2,
1×4, 1×8, (backward) or ¡×2, ¡×4,
¡×8, (forward).
The on-screen display appears on the screen. The
Time Search box shows the elapsed playing time of
the current disc.
2 Within 10 seconds, press [5]/[∞] to select the
Time Search icon in the on-screen display.
The “ – : – –: – –” appears in the Time Search box.
3 Within 10 seconds, use the number buttons to
enter the required start time.
Enter hours, minutes, and seconds from left to right
3 To return to normal playback, press [3/8]
(PLAY [3] on the remote control).
in the box.
4 Within 10 seconds, press [ENTER] to confirm
the start time.
Playback starts from the selected time on the disc.
• If you enter an invalid time, playback will continue
from the current point.
Repeat
DVD
is Off.
- Chapter/Title/Off. The default settings
⁄
1 To repeat the chapter currently playing, press
[REP] ([REPEAT] on the remote control).
The Chapter icon appears on the TV screen.
•
On a Video CD with PBC, you must set PBC to Off on the
setup menu (page 21).
2 To repeat the title currently playing, press
[REP] ([REPEAT] on the remote control) again.
The Title icon appears on the TV screen.
3 To exit the repeat mode, press [REP] ([REPEAT]
on the remote control) again.
The Off icon appears on the TV screen.
|
24 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc menu
DVDs may offer menus that allow you to access
special features.
Changing the audio language
DVD
DVD
1 Press [AUDIO] repeatedly on the remote
control during playback to hear a different
audio language.
1 Press [DISC MENU] ([DISC MENU/SETUP] on
the remote control).
The disc menu is displayed.
2 Use [5]/[∞]/[2]/[3] to highlight your
selection, then press [ENTER].
Changing the audio channel
3 To remove the disc menu, press [DISC MENU]
([DISC MENU/SETUP] on the remote control)
again.
VCD
1 Press [AUDIO] repeatedly on the remote
control during playback to hear a different
audio channel (STEREO, Left or Right).
PBC menu
VCD
1 Press [DISC MENU/SETUP] or [RETURN] on the
remote control to return to the menu screen.
Menu settings and operating procedures may
differ. Follow the instructions on the each menu
screen.
Subtitles
DVD
1 Press [SUBTITLE] on the remote control
repeatedly during playback to see the
different subtitle languages.
You also may set PBC to On under setup (page 21).
⁄
•
If the icon appears, the feature is not available on the
disc.
Camera angle
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback.
Zoom
The zoom function allows you to enlarge the video
image.
1 Press [ANGLE] repeatedly on the remote
control during playback to select a desired
angle.
The number of the current angle appears on the
display.
1 Press [ZOOM] repeatedly during playback or
in the pause mode to enlarge the image.
•
: 100%—400%—1600%
: 100%—400%
DVD
•
VCD
You can move through the zoomed picture
using [5]/[∞]/[2]/[3].
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Photo Operation
JPEG/TIFF disc compatibility
with this player is limited as
follows:
• Depending upon the size and the number of JPEG/
TIFF files, it could take a long time for this unit to
read the disc’s contents. If you do not see an on-
screen display after several minutes, some of the
files may be too large — reduce the resolution of
the JPEG/TIFF files to less than 2M pixels as 2760 ×
2 048 pixels and burn another disc.
Viewing slide shows
This unit can play discs with JPEG or TIFF files.
1 Insert a disc in the unit.
For a disc that includes only photo files, “READING”
appears on the display, and slide show starts
automatically.
2 Press [DISPLAY] to show or hide the help bar
while viewing the slide show.
3 Press [DISC MENU] ([DISC MENU/SETUP] or
STOP [7] on the remote control) to return to
the menu screen.
• The total number of files on the disc should be less
than 3 000.
• Some discs may be incompatible due to a different
recording format or the condition of disc.
• Ensure that all the selected files have the .jpg or .tiff
extensions when copying into the disc.
• If the files have .jpe or .jpeg extensions, please
rename them as .jpg file.
3
4
1
2
5
6
• File names without .jpg or .tiff extension will not
be able to be read by this unit. Even though the
files are shown as JPEG or TIFF image files on the
computer.
7
8
9
• Some JPEG/TIFF files may not operate due to a
different encoding format or the condition of disc.
1. Current file number/Total file number
2. Previous file name
3. Slide show interval time (SLOW, NORMAL, FAST,
OFF)
4. Repeat mode
5. Current folder name
6. Thumbnail image
7. Current file name
8. Resolution
9. Next file name
⁄
•
For a disc that includes audio and movie files, the media
type indicator tabs, MUSIC and MOVIE will be displayed
along with PHOTO. To play the photo file, select PHOTO
and then press [ENTER]/[3/8](PLAY [3]on the remote
control). About the the media type indicator tab, refer to
Selecting a media type on page 10.
|
26 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving to another folder
Viewing still picture
1 Press [5]/[∞] to select the previous or next
1 Press [38] ([8] on the remote control) during
the slide show.
folder in the disc.
The player will now go into the pause mode.
• If the slide show interval time is OFF, you cannot
perform this function.
Moving to another file
2 To return to the slide show, press [38] again
(PLAY [3] on the remote control).
1 Press [2]/[3] to select the previous or next file
in the selected folder.
Zoom
Slide show interval time
1 While viewing images, press [ZOOM] to
enlarge the image (100%—400%—1600%).
• You can move through the zoomed picture using
[5]/[∞]/[2]/[3].
• To cancel the zoom mode, press PLAY [3] on the
remote control.
1 Press [DISC MENU] ([DISC MENU/SETUP] or
STOP [7] on the remote control) to return to
the menu screen.
2 Press [1]/[¡] on the remote control to
select the option you want to use.
It shows the slide show interval time:
FAST—OFF—SLOW—NORMAL
⁄
•
The zoom function may not work when the size of the
file is too small.
(FAST: 3 sec, NORMAL: 8 sec, SLOW: 13 sec)
Rotating the picture
Repeat
1 During watching pictures, press [5]/[∞]
during showing a picture to rotate the picture
clockwise or counter clockwise.
1 Press [REP] ([REPEAT] on the remote control )
to select the option you want to use.
There are 2 repeat mode: ALL or FOLDER.
• ALL: Plays repeatedly on the disc.
• FOLDER: Plays repeatedly on the current folder.
English
|
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie Operation
DivX disc compatibility with
this player is limited as follows:
Playing a movie file
This unit can play discs with movie files.
• Available resolution size of the DivX file is under
720×576 (W×H) pixel.
• The file name of the DivX subtitle is available by 25
characters.
• If the number of the screen frame is over 30 per 1
second, this unit may not operate normally.
• If the video and audio structure of recorded file is
not interleaved, either video or audio is outputted.
Playable Movie file
1 Insert a disc in the unit.
For a disc that includes movie files or movie/ photo
files, “READING” appears in the display, and playback
starts automatically.
2 Press [DISC MENU] ([DISC MENU/SETUP] or
STOP [7] on the remote control) to return to
the menu screen.
.avi, .divx, .div, .asf
Playable subtitle format
.srt, .smi, .ssa, .sub, .txt, .ass
3
4
1
5
2
Playable Codec format
6
DivX3, DivX4, DivX5, Xvid, MP4S
Playable Audio format
7
Dolby Digital, MP3
• Sampling frequency: 48 kHz (Dolby Digital), within
8 kHz to 48 kHz (MP3)
8
9
• Bit rate: within 64 kbps to 640 kbps (Dolby Digital),
within 8 kbps to 320 kbps (MP3)
1. Current file number/Total file number
2. Elapsed time
3. Playback status (Pre stop 87, stop 7)
4. Repeat mode
5. Previous file name
6. Current folder name
7. Current file name
8. Subtitle file name
9. Next file name
⁄
•
For a disc that includes audio and photo files,the media
type indicator tabs, MUSIC and PHOTO will be displayed
along with MOVIE. To play the movie file, select MOVIE
and then press [ENTER]/[3/8] (PLAY [3] on the remote
control). About the the media type indicator tab, refer to
Selecting a media type on page 10.
|
28 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing DivX VOD content
Stop
Some DivX VOD (video on demand) content may
only be playable a fixed number of times. When
you load a disc containing this type of DivX VOD
content, the remaining number of plays is shown
on-screen and you then have the option of playing
the disc (thereby using up one of the remaining
plays), or stopping. If you load a disc that contains
expired DivX VOD content (for example, content
that has zero remaining plays), Rental expired is
displayed.
1 Press [7] on the Pre-Stop mode.
“STOP” appears in the display and the movie menu
appears on the screen.
2 To return to playback, if you press [38] (PLAY
[3] on the remote control), it will be played
from the beginning of the current file.
Pause
• If your DivX VOD content allows an unlimited
number of plays, then you may load the disc into
your player and play the content as often as you
like, and no message will be displayed.
1 Press [3/8] ([8] on the remote control) during
playback.
2 To return to playback, press [38] (PLAY [3] on
⁄
the remote control).
•
In order to play DivX VOD content on this unit, you first
need to register the unit with your DivX VOD content
provider. About your registration code, refer to DivX VOD
(page 21)
•
DivX VOD content is protected by a DRM (Digital Rights
Management) system. This restricts playback of content
to specific, registered devices.
Still picture and frame-by-
frame playback
1 Press [38] ([8] on the remote control) during
playback.
The unit will now go into the PAUSE mode.
Pre-Stop
2 You can advance the picture frame-byframe
by pressing [8] on the remote control
repeatedly.
1 Press [7] on the remote control during
playback.
“PRE-STOP” appears in the display and the movie
3 To return normal playback, press [38] (PLAY
menu appears on the screen.
[3] on the remote control).
2 To return to playback, if you press [38] (PLAY
[3] on the remote control) on the Pre-Stop
mode, it will be played from this point you
stop.
English
|
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie Operation
Slow motion
Repeat
All files or the folder on the disc is played
repeatedly. The default settings is All.
1 Press [38] ([8] on the remote control) during
playback.
The unit will now go into the PAUSE mode.
1 To repeat all files of current folder, press and
hold [REP] ([REPEAT] on the remote control)
during playback.
2 Use [¡] on the remote control to select the
required speed:
The Folder icon appears on the TV screen.
1/16,
1/8,
1/4, or
1/2 (forward)
2 To repeat all files of the disc, press [REP]
([REPEAT] on the remote control) again during
playback.
3 To exit Slow Motion mode, press [38] (PLAY
[3] on the remote control).
⁄
The All icon appears on the TV screen.
•
Slow motion playback in reverse is not possible with
movie file.
3 To repeat the current file, press [REP]
([REPEAT] on the remote control) during
playback.
The File icon appears on the TV screen.
Scan
1 Press [1]/[¡] on the remote control during
playback.
Time search
2 Press [1]/[¡] repeatedly on the remote
control to select the required speed:
The Time Search function allows you to start playing
at any chosen time on the file.
1×2, 1×4, 1×16 ,1×32 (backward) or
1 Press [DISPLAY] on the remote control during
playback.
The on-screen display appears on the screen. The
Time Search box shows the elapsed playing time of
the current disc.
¡×2, ¡×4, ¡×16, ¡×32 (forward).
3 To return to normal playback, press [3/8]
(PLAY [3] on the remote control).
2 Within 10 seconds, press [5]/[∞] to select the
Time Search icon in the on-screen display.
The “– : – –: – –” appears in the Time Search box.
Skip
1 Press [2]/[3] ([4]/[¢] on the remote
control) during playback to select the next file
or to return to the beginning of the current
file.
3 Within 10 seconds, use the number buttons to
enter the required start time.
Enter hours, minutes, and seconds from left to right
in the box.
2 Press [2] ([4] on the remote control) twice
4 Within 10 seconds, press [ENTER] to confirm
the start time.
briefly to step back to the previous file.
Playback starts from the selected time on the file.
• If you enter an invalid time, playback will continue
from the current point.
3 To go directly to any file on the movie menu,
press [SEARCH] and then press the file number
you want with number buttons ([0] to [9]).
|
30 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
AUX Operation
Changing the audio language
Playing an auxiliary equipment
Before operating the auxiliary equipment using
the following procedure, select the external input
correctly. Refer to AUX (Auxiliary) ON/ OFF (page
12). You can connect auxiliary equipment to this
unit.
1 Press [AUDIO] repeatedly on the remote
control during playback to hear a different
audio language or audio file.
⁄
•
If the icon appears, the feature is not available on the
disc.
1 Connect the auxiliary equipment to the
auxiliary input on the unit.
Subtitles
1 Press [SUBTITLE] on the remote control
repeatedly during playback to see the
different subtitle languages.
2 Press [SRC] to select the AUX IN.
⁄
“AUX IN” appears in the display.
•
If the icon appears, the feature is not available on the
disc.
3 Turn on the connected auxiliary equipment
and start playing the source.
4 Adjust the volume.
⁄
Notice for displaying the DivX
subtitle
If the subtitle does not display properly during
playback, please follow the steps below.
•
•
•
Connect a portable audio device with mini-plug cable
(3.5 ø).
Use the mini-plug cable which is stereo type and does
not have any resistance.
If the input level of the auxiliary equipment connected
to the AUX input jack is not high enough, adjust the
input level properly. Refer to AUX (Auxiliary) 0 dB/+6 dB
(page 12).
1 Press and hold [SUBTITLE] on the remote
control for about 3 seconds.
The number of character set will appear.
2 Press [SUBTITLE] on the remote control to
select another character set until the subtitle
is displayed properly.
No.
Character set
Central Europe
Cyrillic
West european latin
Greek
CP1250
CP1251
CP1252
CP1253
CP1254
Turkish
⁄
•
•
If the subtitle setup menu does not have the DivX
subtitle language that you are going to play, the subtitle
language may not be displayed properly.
If you select a character set for DivX subtitle, the setting
is also applied to MP3 tag.
English
|
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Language code list
Enter the appropriate code number for the initial settings Disc Audio, SUBTITLE and/or Menu (page 18).
Language
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
Language
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Code
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
Language
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Volapük
Welsh
Wolof
Code
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8679
6789
8779
8872
7473
8979
9085
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Xhosa
Yiddish
Yoruba
Polish
Portuguese
Zulu
|
32 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Area code list
Enter the appropriate code number for the initial setting Area Code (page 21).
Area
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CA
DK
EC
EG
SV
ET
Area
Code
HM
Area
Code
PY
PH
PL
Heard and McDonald
Islands
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Paraguay PY
Philippines
Poland
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
Portugal
PT
Romania
Russian Federation
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Libya
Luxembourg
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
LU
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
FJ
FI
FR
DE
GB
GR
GL
Pakistan
Panama
Greenland
English
|
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Installation Procedure
•
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Accessories
•
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
This unit has the cooling fan (page 36) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
1
..........1
..........2
•
•
•
2
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
•
•
•
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
•
•
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
•
|
34 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Removing the Unit
Installation
Removing the hard rubber
frame
Metal mounting strap
(commercially available)
1 Extend top and bottom of the frame outwards to
remove the frame. (When reattaching the frame,
point the side with a groove downwards and
attach it.)
Firewall or metal support
Bend the tabs of the
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
⁄
•
Self-tapping screw
(commercially available)
It becomes easy to remove the frame if the faceplate is
released.
Screw (M4X8)
(commercially available)
Removing the Unit
⁄
1 Refer to the section <Removing the hard rubber
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
frame> and then remove the hard rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Screw (M4X8)
(commercially available)
Accessory2
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands, being
careful not to drop it.
English
|
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Television monitor, etc
(optional accessory)
Visual output (Yellow)
Parking sensor wire Detection
cable (Light Green)
H.BRK
For the sake of safety, be
sure to connect the parking
sensor.
Cooling fan
Fuse (10A)
FM/AM antenna input (JASO)
Antenna Cord
Digital optical out
(Do not use)
Subwoofer preout
Rear preout
Wiring harness
(Accessory1)
Power control wire (Blue/White)
Connect either to the power control terminal when
using the optional power amplifier.
REMOTE ON
Depending on what antenna you are using,
connect either to the control terminal of the motor
antenna, or to the power terminal for the booster
amplifier of the film-type antenna.
Motor antenna control wire (Blue)
POWER ANTENNA
Mute wire (Orenge)
Connect to the terminal that is grounded when
either the telephone rings or during conversation.
PHONE MUTE
DIMMER
Dimmer control wire (Pink)
To car light control switch
Ignition key
switch
Car fuse box
ACC
Ignition wire (Red)
TO IGNITION
Battery wire (Yellow)
TO BATTERY (+)
Car fuse box
(Main fuse)
Ground wire (Black) - (To car chassis)
GROUND(–)
+
–
Battery
|
36 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
Functions
External Power
Connector
Blue/White
Orange
Yellow
Blue
Pink
Red
Power control
Phone Mute
Battery
Power Antenna
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
A-1*
A-2*
A-4
A-5
A-6*
A-7
Connector Function Guide
Connector B
A-8
Black
ꢀ
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
ꢀ
Connector A
B-8
Green/Black
⁄
•
*You have to check connector pin function of a vehicle.
FRONT LEFT SPEAKER (+)
FRONT LEFT SPEAKER (–)
White
+
To front left
speaker
–
White/Black
Gray
FRONT RIGHT SPEAKER (+)
FRONT RIGHT SPEAKER (–)
+
To front right
speaker
–
Gray/Black
Green
REAR LEFT SPEAKER (+)
REAR LEFT SPEAKER (–)
+
To rear left
speaker
–
Green/Black
Purple
REAR RIGHT SPEAKER (+)
REAR RIGHT SPEAKER (–)
+
To rear right
speaker
–
Purple/Black
English
|
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
Audio file source
? The sound skips when an Audio file is being
played.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling discs> (page 7).
General
The recording condition is bad.
Record the media again or use another media.
? The power does not turn ON.
☞
✔
The fuse has blown.
☞
After checking for short circuits in the wires,
replace the fuse with one with the same rating.
✔
The speaker wire has a short-circuit or touches
the chassis of the vehicle, and then the protection
function is activated.
☞
Wire or insulate the speaker cable properly and
press the reset button.
? No sound can be heard, or the volume is low.
✔
The fader or balance settings are set all the way to
one side.
☞
Center the fader and balance settings.
✔
The input/output wires or wiring harness are
connected incorrectly.
☞
Reconnect the input/output wires or the wiring
harness correctly. Refer to the <Connecting Wires
to Terminals> (page 36).
? The sound quality is poor or distorted.
✔
One of the speaker wires is being pinched by a
screw in the car.
☞
Check the speaker wiring.
✔
The speakers are not wired correctly.
☞
Reconnect the speaker wires so that each output
terminal is connected to a different speaker.
Tuner source
? Radio reception is poor.
✔
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
<Connecting Wires to Terminals> section (page
36).
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is severely scratched.
Try another disc instead.
☞
☞
|
38 KDV-3241Y
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
FM tuner section
Audio section
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
Maximum output power
: 50 W x 4
Signal to Noise ratio (MONO)
: 57 dB
Stereo separation (1 kHz)
: 25 dB
Output power (DIN 45324, +B=14.4V)
: 30 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone action
Bass : 100 Hz 8 dB
MW tuner section
Frequency range (9 kHz space)
: 522 kHz – 1620 kHz
Usable sensitivity (S/N = 20dB)
: 28 μV
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (CD)
: 4000 mV/47 kΩ
Preout impedance
: ≤ 600 Ω
DVD player section
D/A Converter
Auxiliary input
Frequency response ( 3 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
: 24 bit
Decoder
: Linear PCM/ Dolby Digital/ dts/ MP3/ WMA
Wow & Flutter
: Below Measurable Limit
Frequency Response
Sampling frequency; 96 kHz : 20 – 44,000 Hz
Sampling frequency; 48 kHz : 20 – 22,000 Hz
Sampling frequency; 44.1 kHz : 20 – 20,000 Hz
Total Harmonic Distortion
: 0.05 % (1 kHz)
S/N Ratio (dB)
: 100 dB (1 kHz)
Dynamic Range
: 96 dB
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 165 mm
Weight
: 1.70 kg
Sampling frequency
: 32/ 44.1/ 48/ 96 kHz
Quantifying bit number
: 16/ 20/ 24 bit
MP3 Decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA Decode
: Compliant with Windows Media Audio
Specifications subject to change without notice.
English
|
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|