Kenwood Car Video System DDX6036 User Manual

MONITOR WITH DVD RECEIVER  
DDX6036  
DDX6036M  
INSTALLATION MANUAL  
© B54-4756-00 (MW/M2W)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Procedure  
1. To prevent a short circuit, remove the key from the  
ignition and disconnect the - battery.  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
4. Connect the wiring harness wires in the following  
order: ground, battery, ignition.  
5. Connect the wiring harness connector to the unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
¤
Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
Make sure to ground the unit to a negative 12V DC power  
supply.  
Do not install the unit in a spot exposed to direct sunlight  
or excessive heat or humidity. Also avoid places with too  
much dust or the possibility of water splashing.  
Do not use your own screws. Use only the screws provided.  
If you use the wrong screws, you could damage the unit.  
If the power is not turned ON (“PROTECT” is displayed),  
the speaker wire may have a short-circuit or touched the  
chassis of the vehicle and the protection function may  
have been activated. Therefore, the speaker wire should be  
checked.  
9. Perform the Initial Setup. (Refer to the Instruction  
Manual.)  
2WARNING  
If your car’s ignition does not have an ACC position, connect  
the ignition wires to a power source that can be turned on  
and off with the ignition key. If you connect the ignition  
wire to a power source with a constant voltage supply, as  
with battery wires, the battery may die.  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
Do not cut out the fuse from the ignition wire (red) and the  
battery wire (yellow). The power supply must be connected  
to the wires via the fuse.  
If the console has a lid, make sure to install the unit so that  
the faceplate will not hit the lid when closing and opening.  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with one  
with the same rating.  
¤CAUTION  
Install this unit in the console of your vehicle.  
Do not touch the metal part of this unit during and  
shortly after the use of the unit. Metal part such as the  
heat sink and enclosure become hot.  
Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail to  
work if you share the - wires or ground them to any metal  
part in the car.  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals (do  
not mix front and rear). For example, if you connect the +  
connector of the left speaker to a front output terminal, do  
not connect the - connector to a rear output terminal.  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
This unit has the cooling fan (page 5) to decrease the  
internal temperature. Do not mount the unit in a place  
where the cooling fan of the unit are blocked. Blocking  
these openings will inhibit the cooling of the internal  
temperature and result in malfunction.  
About the Front Panel  
When removing the product from the box or installing  
it, the front panel may be positioned at the angle  
shown in (Fig. 1). This is due to the characteristics of a  
mechanism the product is equipped with.  
If the program that is activated when the product is  
first powered on works properly, the front panel will  
automatically move into the position (initial setting  
angle) shown in (Fig. 2).  
(Fig. 1)  
(Fig. 2)  
Do not press hard on the panel surface when installing the  
unit to the vehicle. Otherwise scars, damage, or failure may  
result.  
After the Installation  
After the installation, perform the <Initial Setup>  
(Refer to the Instruction Manual) by referring to the  
instruction manual.  
|
English  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connection  
If you connect the ignition wire (red) and the battery  
wire (yellow) to the car chassis (ground), you may  
cause a short circuit, that in turn may start a fire. Always  
connect those wires to the power source running  
through the fuse box.  
¤
Ignition key  
switch  
ACC  
A
B
Ignition wire (Red)  
A
Car fuse box  
Battery wire (Yellow)  
Car fuse box  
(Main fuse)  
B
FM/AM  
antenna input  
Antenna Cord  
Ground wire (Black) -  
(To car chassis)  
C
C
Battery  
Connect to the vehicle's parking brake  
detection switch harness.  
Parking sensor wire (Light Green)  
PRK SW  
For the sake of safety, be sure to connect the parking sensor.  
Reverse sensor wire (Purple/White)  
Connect to vehicle's reverse lamp harness when  
using the optional rear view camera.  
Steering remote control input (Light Blue/Yellow)  
To steering remote  
To use the steering wheel remote control feature, you need to  
an exclusive remote adapter (not supplied) matches your car is  
required. When this terminal is not in use, leave its cap on.  
Dimmer control wire (Orange/White)  
Mute wire (Brown)  
To car light control switch  
Connect to the terminal that is grounded when either  
the telephone rings or during conversation.  
To connect the Kenwood navigation system,  
consult your navigation manual.  
Depending on what antenna you are using,  
Motor antenna control wire (Blue)  
Power control wire (Blue/White)  
connect either to the control terminal of the motor antenna, or to the  
power terminal for the booster amplifier of the film-type antenna.  
When using the optional power amplifier,  
connect to its power control terminal.  
If no connections are made, do not let the cable come out from the tab.  
|
4
DDX6036/DDX6036M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cooling fan  
FUSE ( 15A )  
Accessory 1  
REVERSE  
STEERING WHEEL  
REMOTE INPUT  
REMOTE CONT  
White/Black  
To front left speaker  
To front right speaker  
To rear left speaker  
To rear right speaker  
+
+
+
+
White  
Gray/Black  
ILLUMI  
MUTE  
Gray  
Green/Black  
Green  
Purple/Black  
ANT. CONT  
P.CONT  
Purple  
|
English  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
System Connection  
USB terminal  
USB device  
(commercially available)  
Audio input (iPod/AV Input 2 switchable)  
Resistance-free stereo type mini plug (3.5φ)  
Visual input (iPod/AV Input 2 switchable)  
Resistance-free mini plug (3.5φ)  
Accessory  
2
Accessory 3  
Audio/Visual Output  
• Visual output (Yellow)  
• Audio left output (White)  
• Audio right output (Red)  
Audio/Visual input  
• Visual input (Yellow)  
• Audio left input (White)  
• Audio right input (Red)  
Rear View Camera Input  
• Visual input (Yellow)  
Front Preout  
• Audio left output (White)  
• Audio right output (Red)  
Rear Preout  
• Audio left output (White)  
• Audio right output (Red)  
Subwoofer Preout  
• Audio left output (White)  
• Audio right output (Red)  
|
6
DDX6036/DDX6036M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Optional Accessory Connection  
iPod  
(commercially available)  
KCA-iP301V  
(Optional Accessory)  
Visual Output (Yellow)  
Audio Output (Black)  
USB terminal  
USB terminal  
KCA-BT200  
(Optional Accessory)  
Connection cable  
(Included in the KCA-BT200)  
Navigation System  
(Optional Accessory)  
1
2
3
Type Switch  
1 2 3  
TV Tuner  
(Optional Accessory)  
T V A N T E N N A I U T  
Connection cable  
(Included in the Navigation  
System)  
R O U N I T  
M O O T N I T  
Navigation units that can be connected to this unit.  
(As of December, 2009):  
KNA-G630  
KNA-G630CN  
For latest information, access the  
Connection cable  
(Included in the TV tuner)  
|
English  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Escutcheon  
For General Motors  
For Toyota/Scion  
1. Cut out accessory 5 to meet the shape of the  
1. Cut out accessory 5 as illustrated.  
opening of the center console.  
2. Attach accessory 5 to the unit.  
Cutting line  
Cut out to meet the shape of  
the opening in the vehicle.  
Accessory 5  
Accessory 5  
2. Fold double-sided adhesive (accessory 6) along  
the slit and attach it to accessory 5 cut-out  
against the center rib as illustrated. Use 2 pieces of  
accessory 6 for 1 accessory 5 cut-out.  
For Volkswagen  
3. Attach accessory 5 cut-out to the unit.  
1. Attach accessory 9 to the unit.  
Accessory 6  
Accessory 9  
|
8
DDX6036/DDX6036M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation for Monitor/Player Unit  
Bend the tabs of the mounting  
sleeve with a screwdriver or similar  
utensil and attach it in place.  
Make sure that the unit is installed securely in place. If the unit is unstable,  
it may malfunction (eg, the sound may skip).  
Installation on Toyota, Nissan or Mitsubishi Car using Brackets  
Accessory 7 (M5x6mm)  
or Accessory 8 (M5x7mm)  
Car Bracket  
Accessory 7 (M5x6mm)  
or Accessory 8 (M5x7mm)  
|
English  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing Monitor/Player Unit  
Removing the Hard Rubber Frame  
(escutcheon)  
Removing the Unit  
1. Remove the hard rubber frame by referring to the  
removal procedure in the section <Removing the  
Hard Rubber Frame>.  
2. Insert the two removal tools 4 deeply into the  
slots on each side, as shown.  
1. Engage the catch pins on the removal tool 4 and  
remove the two locks on the lower level.  
Lower the frame and pull it forward as shown in  
the figure.  
Accessory 4  
Accessory 4  
Catch  
Lock  
3. Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
The frame can be removed from the top side in the same  
manner.  
2. When the lower level is removed, remove the  
upper two locations.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
4. Pull the unit all the way out with your hands, being  
careful not to drop it.  
|
10  
DDX6036/DDX6036M  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Infinity Speaker BU 1 User Manual
InFocus Computer Monitor INF55WIN8 User Manual
JBL Speaker PSW D112 115 User Manual
Jenn Air Convection Oven W30400S User Manual
Jensen Car Video System VM8022 User Manual
JVC CD Player KD G710 User Manual
JVC Computer Monitor TM A140PN A User Manual
Kenwood Portable CD Player KDC MP445U User Manual
KitchenAid Clothes Dryer KEYL507W User Manual
Kompernass MP3 Player KH 2257 User Manual