DUAL DIN SIZED CD RECEIVER
DPX503U
DPX303
DPX313
INSTRUCTION MANUAL
Declaration of Conformity with regard to the EMC Directive
2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
© B64-4227-00/00 (EW/ E2W)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-5 or ISO 8859-
1 can be displayed. Refer to “MENU” > “Russian” of
<Function Control> (page 6).
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 18).
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• In this document, the description indicator will light
means a status is displayed. Refer to <About Display
Type> (page 9) for the details of the status display.
How to reset your unit
• The illustrations of the display, the function icon and
the panel appearing in this manual are examples
used to explain more clearly how the controls are
used. Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
• If this unit or the connected unit (disc auto changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
Reset button
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
CDs that cannot be used
• CDs that are not round cannot be used.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
English
|
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
ꢀ
[
]
Disc slot
[SRC]
[TI]
[FNC]
Control knob
[1]—[6] USB Terminal Auxiliary input
[AUD] [ATT]
(DPX503U only)
The audio system comes back on when [SRC] is
pressed during a call.
General functions
Power/Source Select button: [SRC]
Turns on the power.
When the power is ON, select a source.
SRC Select mode 1: Press the [SRC] button and then
turn the Control knob or push it toward left or right.
To determine the selected source, press the Control
knob.
SRC Select mode 2: Pressing this button each time
switches between sources.
Tuner (“TUNER”), USB or iPod (“USB” or “iPod”)
(DPX503U only), CD (“Compact Disc”), Auxiliary input
(“AUX”), and Standby (“STANDBY”)
⁄
•
To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (page
31).
Auxiliary input: Auxiliary input
Connect a portable audio device with mini-plug
cable (ø3.5 mm).
⁄
•
Use the mini-plug cable which is stereo type and does not
have any resistance.
•
The auxiliary input requires the setting made in “MENU” >
Press at least 1 second to turn off the power.
“Built in AUX” of <Function Control> (page 6).
⁄
Subwoofer output: Control knob
•
•
•
The SRC Select mode can be set in “MENU” > “SRC Select” of
Switches between ON (“SUBWOOFER ON”) and OFF
(“SUBWOOFER OFF”) each time pushing toward down
for at least 2 seconds.
<Function Control> (page 6).
When an optional accessory is connected, the source name
for each device appears.
This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle's battery. The time until full power OFF can be set in
“Power OFF” of <Function Control> (page 6).
⁄
•
This function requires the setting made in “MENU” >
“SWPRE” of <Function Control> (page 6).
Function Control: [FNC]
•
When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”. (DPX503U only)
Pressing this button allows you to set various
functions using the Control knob. Refer to <Function
Control> (page 6).
Volume control: [AUD]
Turn the knob to adjust the volume.
Category
MENU
SOUND*
DISP
Function of setup item
Attenuator: [ATT]
Allows you to set up the environment.
Allows you to set up the sound environment.
Allows you to set up the display.
Turning the volume down quickly.
When the volume is reduced, the “ATT” indicator
flashes.
COLOR*
Allows you to set up the illumination color.
Muting volume upon reception of phone call
When there is a call, “CALL” is displayed and the audio
system is paused.
When the call ends, “CALL” disappears and the audio
system comes back on.
*Function of DPX503U
Text/Title scroll: Control knob
Scrolls the CD, audio file, and Radio text display when
pushing toward up for at least 2 seconds.
|
4
DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Pause and play: Control knob
Switches between pause and play each time the
center is pressed.
Tuner functions
Band select: Control knob
Switches between FM1, FM2, and FM3 each time
USB device removing (DPX503U only): [0]
Press this button for 2 seconds or longer to select the
remove mode, and the remove the USB device.
During the remove mode, the “USB REMOVE”
indicator is ON.
pushing toward up.
Switches to AM when pushing toward down.
Tuning: Control knob
Changes the frequency when pushing toward left or
right.
Music search: Control knob
⁄
Changes the music when pushing toward left or right.
Fast reverses or forwards the music while keeping
pushing toward left or right. (No sound is output
while playing audio file.)
•
During reception of stereo stations the “ST” indicator is ON.
Auto memory entry:[TI]
Memorizes six stations with good reception
automatically when pressed for at least 2 seconds.
Folder search: Control knob
Changes the folder containing the audio file when
Preset memory: [1] – [6]
Memorize the station selected when pressing for at
pushing toward up or down.
least 2 seconds.
Track/ File/ Folder repeat play: [4]
Switches between Track Repeat (“Repeat ON”) and
OFF when pressed while playing a CD.
Preset tuning: [1] – [6]
Recalls the memorized station.
Switches between File Repeat (“File Repeat ON”),
Folder Repeat (“Folder Repeat ON”), and OFF when
pressed while playing an audio file.
Traffic Information: [TI]
Turns ON or OFF the Traffic Information function. If
traffic bulletin starts when the function is ON, “Traffic
INFO” is displayed and traffic information is received.
•
The folder repeat operation cannot be performed
while iPod is playing.
⁄
⁄
•
If the volume is adjusted during reception of traffic
information, the adjusted volume is memorized
automatically. The memorized volume will be applied next
time the Traffic Information function is turned ON.
Scan play: [2]
Successively plays the intro of the music in the disc
or folder.
Switches between ON (“Scan ON”/ “File Scan ON”) and
OFF each time this button is pressed.
Disc & Audio file play functions
Disc play: Disc slot
•
The Scan play operation cannot be performed while
iPod/ “Media Editer” media is playing.
⁄
Starts playing when a disc is inserted.
When a CD is inserted, the “IN” indicator is ON.
Random play: [3]
Randomly plays the music in the disc or folder.
Switches between ON (“Disc Random ON”/ “Folder
RDM ON”) and OFF each time this button is pressed.
⁄
•
3 inch (8 cm) CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
Disc ejection: [0]
⁄
•
You can eject the disc for 10 minutes after switching off the
engine.
USB device/iPod play (Function of DPX503U):
USB Terminal
Connecting a USB device starts playback.
⁄
•
For the playable audio file, media, and devices, refer to
<About Audio file> (page 26).
English
|
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Control
Functions in the table below can be set up by using Function Control.
Category Item
Setting
Entry Setting overview
1 sec.
Condition Page
Sets/Resets security code
MENU
“Security Set”/
“Security Clear”
“SRC Select”
17
Sets the source selection method.
“1”*/“2”
27
13
“iPod Mode”*1 “OFF”/“ON”*
When set to “ON”, allows you to select music in the manner
similar to that of the iPod.
When the iPod source is used, sets whether the illumination
color is changed by the iPod.
“AT COL CHG”*1 “OFF”/“iPod”*
28
Setting the operation check sound (beep sound) ON/OFF.
“Beep”
“OFF”/“ON”*
Sets the clock.
Sets the date.
“Clock Adjust”
“Date Adjust”
“Date Mode”
“SYNC”
1 sec.
1 sec.
1 sec.
—
—
18
18
Sets the date display mode.
7 types
“OFF”/“ON”*
Synchronizing the RDS station time data and this unit’s
clock.
A red indicator will blink on the unit after the ACC is set to
OFF, warning potential thieves.
“DSI”
“OFF”/“ON”*
Turns off the display when no operation is performed.
“Display”
“Dimmer”
“OFF”/“ON”*
“OFF”/“ON”*
27
27
Dims the display part in conjunction with the light switch
of the vehicle.
Sets whether the illumination is dimmed in conjunction
with the light switch of the vehicle or it is dimmed
constantly.
“ILM Dimmer” “AUTO”*/“MNAL”/
“OFF”
Sets whether the illumination color is changed in
conjunction with the key operation. (To connect the
Bluetooth unit)
“ILM Effect”
“OFF”/“ON”*
Sets whether the key illumination color is changed in
conjunction with the sound volume.
Sets the button illumination color.
“ILM MSC SYNC” “OFF”*/“ON”
—
“ILM Color”*2
“Blue”*/ ”Red”/
”Green”
Sets the preout output.
“SWPRE”
“AMP”
“Rear”*/“Sub-W”
27
27
27
Turns on/off the built-in amplifier.
“OFF”/“ON”*
Specifies the destination of AUX input sound when the Dual
Zone function is turned on.
“Zone2”
“Rear”*/“Front”
Turns ON/OFF the Supreme function.
“Supreme”
“OFF”/“ON”*
27
Controls the connected LX amplifier.
Turns ON/OFF the News Bulletin Automatic Reception
function and sets the news bulletin interrupt disabled time.
“AMS Control”
“News”
1 sec.
—
18
28
“OFF”*/“00min”
–“90min”
Only stations whose reception is good are searched in auto
seek tuning.
Selects the tuning mode of the radio.
“Local Seek”
“Seek Mode”
“AF”
“OFF”*/“ON”
“Auto1”*/“Auto2”/
“Manual”
“OFF”/“ON”*
28
28
When station reception is poor, automatically switches to
the station that is broadcasting the same program over the
same RDS network.
Sets whether to switch to the station only in the specific
region using the “AF” control.
“Regional”
“OFF”/“ON”*
When traffic information station reception is poor,
automatically searches for a station that can be received
better.
“Auto TP Seek” “OFF”/“ON”*
You can reduce the noise when stereo broadcasts are
received as monaural.
“MONO”
“OFF”*/“ON”
Sets the disc name (DNPS)/ AUX name.
“Name Set”
1 sec.
11/12
|
6
DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Category Item
“Russian”*3
“Scroll”
Setting
“OFF”/“ON”*
Entry Setting overview
Condition Page
Selects Russian as the display language.
28
When set to “Auto”, scrolls the screen once with the change
of the displayed text.
“Auto”/“Manual”*
—
Sets whether to display AUX during source selection.
“Built in AUX” “OFF”/“ON”*
Turns off the power when the preset time has lapsed in the
Standby mode.
Sets the CD read mode.
“Power OFF”
“-----”/“20min”*/
“40min”/“60min”
“1”*/“2”
28
“CD Read”
“Audio Preset”*2
28
24
Presets the setting value of the audio control. The preset
value is retained after resetting.
1 sec.
Switches the panel display between positive or negative.
“DISP REVERSE” “POSI 1”/“POSI 2”/
“NEGA 1”*/“NEGA 2”
—
Adjusting the display contrast.
“CONTRAST”
“1”–“10”
—
Sets the opening message displayed when the power is
turned on.
Specifies whether to enable demonstration.
Selects the car type to compensate the distance difference
between each speaker.
Makes fine adjustment of the compensation value specified
“OPENING MSGE
Edit”
1 sec.
2 sec.
12
“DEMO Mode” “OFF”/“ON”*
—
18
19
/28
SOUND*1 “S-SET” “CABIN” “Compact1”etc.
“DTA”
19/29
at Cabin.
Makes fine adjustment of the X’Over value specified at
Speaker.
“XOVER”
20
Sets the sound quality.
“S-CTRL” “EQ”
“POSIT”
20
20
/21
Compensates the sound environment in accordance with
the listening position.
Compensates high and low pitch sound at lower volume.
“LOUD” “OFF”*/“ON”
“PRESET”
Presets the setting value of the audio control. The preset
value is retained after resetting.
Sets the display pattern.
Sets the Type D spectrum analyzer display.
Sets the Type A/B side icon display.
21
9
DISP
“TYPE”
“GRAPH”
“SIDE”
A/ B/ C/ D
—
Î
Spectrum Analyzer 1 – 2
Text icon/ Source
icon/ OFF
Åı
Sets the text display.
“TEXT”
“OUT”
ÅıÇ
9
Sets the vehicle-side display.
Sets the Panel illumination color.
Presets a station.
—
Color*1
P.MEM
SCAN
10
15
When set to “ON”, plays the intro of the music in the folder
successively.
“ON”/ —
When set to “ON”, plays the music in the folder randomly.
RDM
“ON”/ —
“ON”/ —
“ON”/ —
“ON”/ —
When set to “ON”, plays the music repeatedly.
FiREP
FoREP
SCAN
When set to “ON”, plays the music in the folder repeatedly.
When set to “ON”, plays the intro of the music on the disc
successively.
When set to “ON”, plays the music on the disc randomly.
RDM
M.RDM
“ON”/ —
“ON”/ —
When set to “ON”, plays the music in the disc changer
randomly.
When set to “ON”, plays the music repeatedly.
T.REP
D.REP
“ON”/ —
“ON”/ —
When set to “ON”, plays the music on the disc repeatedly.
*Factory setting
*1 Function of DPX503U.
*2 Function of DPX303/DPX313.
*3 Function of Russian sales model.
Next page 3
English
|
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Control
Displayed item is depending on currently selected
source or mode. The mark in Condition column shows
the condition to which the item is displayed.
: Can be set in other than standby state.
: Can be set in standby state.
1 Enter Function Control mode
Press the [FNC] button.
Function icon is displayed.
2 Select your desired setup item
: Can be set while Audio file source of CD/USB/iPod.
: Can be set while Audio file source of CD/USB
(excluding iPod).
: Can be set while CD/ Disc changer source.
: Can be set while Disc changer source.
: Can be set during Tuner source.
Operation type
Operation
Movement between items Turn the Control knob.
Selection of item
Press the Control knob.
Return to previous item
Press the [FNC] button or“
”icon.
Repeat selection and determination until your
desired setup item is selected.
: Can be set during FM reception.
: Can be set while accessing AUX source.
: Can be set only during playback of the iPod source.
(USB source used when the iPod is connected)
: Can be set for sources other than the standby source
by setting “2 ZONE” of <Audio Setup> (page 23) to
“ON”.
: Sets “ILM MSC SYNC” and “AT COL CHG” in the menu
to “OFF”.
: Refer to the reference page.
Example:
MENU
DISP COLOR
DISP
MENU
COLOR
TYPE
SIDE TEXT
In this manual, the above selection is
indicated as
Select “DISP” > “TYPE”.
Å–Î : Can be set when the specified type is selected for
Display Type.
— : Can be set during all sources.
3 Make a setting
Turn the Control knob to select a setting value,
and then press the Control knob.
⁄
• The value of items with
mark can be set by
•
•
•
•
Refer to the respective page for information on how to
set the items with reference page number.
Only the items available to the current source are
displayed.
“ILM MSC SYNC” is displayed when “MENU” > “AT COL
CHG” in <Function Control> is set to “OFF”.
Location played with “File Scan”
pushing the Control knob towards right or left.
• Some items require you to keep pressing the
Control knob for 1 or 2 seconds so that you can
make a setting. For these items, the time during
which you need to keep pressing the Control
knob is displayed in the Entry column in seconds.
• For the functions accompanied by the
- Audio file: First 10 seconds
description of the setting procedure and so forth,
the reference page numbers are displayed.
- Music Editor media: First 10 seconds or the part picked
by Intro Skip.
During Intro Skip, turn the control knob left or right to
change the song.
The scan method depends on the Music Editor setting.
See the Music Editor help for details.
4 Exit Function Control mode
Press the [FNC] button for at least 1 second.
|
8
DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
In Audio file source
Information
Music title & Artist name
Album name & Artist name
Folder name
About Display Type
Shown below are examples of display types.
Display
“Title/Artist”/”TITLE”
“Album/Artist”/”ALBUM”
“Folder Name”/”FOLDER”
“File Name”/”FILE”
“P-Time”/”P-TIME”
“Speana/Clock”/”SPEANA”
“Date”/”DATE”
Display
Display Type
“TYPE [A]”
3
1
1
File name
Play time & Music number
Spectrum Analyzer & Clock
Date
“TYPE [B]”
“TYPE [C]”
“TYPE [D]”
2
3
Blank
“Blank”/”BLANK”
In Standby
Information
Standby
Clock
Date
1
6
Display
4
5
“Source Name”/”SRC NAME”
“Clock”/”CLOCK”
“Date”/”DATE”
Blank
“Blank”/”BLANK”
1 Text display part
2 Status display
3 Icon display part
4 Display (varied depending on the source)
5 Clock display
6 Spectrum Analyzer display
In Auxiliary input source
Information
Auxiliary input name
Spectrum Analyzer & Clock
Date
Display
“Source Name”/”SRC NAME”
“Speana/Clock”/”SPEANA”
“Date”/”DATE”
Blank
“Blank”/”BLANK”
1 Enter Text Display Selection mode (In Display
Type A/ B/ C)
Select “DISP” > “TEXT”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Text Display Selection
Changing the text display.
In Tuner source
Information
2 Select the text display part
Display
Push the Control knob towards up or down.
The selected text display part blinks.
Program Service name (FM)
Title & Artist name* (FM)
Station name* (FM)
Radio text plus* (FM)
Radio text (FM)
Frequency (MW, LW)
Spectrum Analyzer & Clock
Date
“Frequency/PS”/“FREQ/PS”
“Title/Artist”/”TITLE/ART”
“Station Name”/”ST NAME”
“Radio Text Plus”/”R-TEXT+”
“Radio Text”/”R-TEXT”
“Frequency”/”FREQ”
“Speana/Clock”/”SPEANA”
“Date”/”DATE”
3 Select the text
Turn the Control knob or push it towards left
or right.
4 Exit Text Display Selection mode
Press the [FNC] button.
Blank
“Blank”/”BLANK”
⁄
•
•
•
If the selected display item does not have any
information, alternative information is displayed.
Some items cannot be selected depending on the
display type and row.
When selecting “Folder Name” while playing with
iPod, names will be displayed depending on currently
selected browsing items.
When Display Type C is selected, “Speana” is displayed
instead of “Speana/Clock.”
“Frequency” can be selected only on the first line while
setting the text.
* Information of Radio text plus is displayed.
In CD & External disc source
Information
Disc title
Track title
Play time & Track number
Disc name
Display
“Disc Title”/”D-TITLE”
“Track Title”/”T-TITLE”
“P-Time”/”P-TIME”
“DNPS”
•
•
•
Spectrum Analyzer & Clock
Date
“Speana/Clock”/”SPEANA”
“Date”/”DATE”
Blank
“Blank”/”BLANK”
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed.
English
|
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Function of DPX503U
Function of DPX503U
Illumination Color Selection
Illumination Color Preset Memory
Selecting the Illumination Color of the panel.
Saving the combination of the Illumination Colors
selected for each place. The memory cannot be
erased by the Reset button.
1 Enter Illumination Color Selection mode
Select “Color” .
For how to select Function Control item, refer to
<Function Control> (page 6).
1 Set the Illumination Color for each place
Refer to <Illumination Color Selection> (page 10).
2 Select the place where you want to set the
Illumination Color
2 Enter Illumination Color Preset Memory mode
Select “COLOR” > “PRESET” > “MEMO”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Place
Display
All
“All Color”
Display
Button
Volume knob
Control konb
“Display Color”
“Key Color”
“Left Knob Color”
“Right Knob Color”
3 Put the Illumination Color Preset in the
memory
Press the Control knob.
“Memory?” is displayed.
Save and recall the Illumination Colors you selected “Color Preset”
for each place
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Memory Completed” is displayed.
Turn the Control knob and push the center
when the desired item is displayed.
5 Exit Illumination Color Preset mode
3 Select the Illumination Color
Turn the Control knob and push the center
when the desired item is displayed.
Select the color from “Variable Scan”/ “Color1”
— “Color 10”/ “User”.
Press the [FNC] button.
⁄
•
•
Register 1 pair of Illumination Color Preset Memory.
If you press the Reset button, the value in the memory
will be default setting value of “Illumination Color
Selection.”
Creating “User” color
You can create your original color during the
selection from “Color1” — “Color10.”
The color you created can be called when you
select “User”.
1. Press the Control knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Operation type
Operation
To select the color to adjust.
(red, green, or blue)
Push the Control knob towards
right or left.
To adjust color. (Range: 0 – 9) Turn the Control knob or push it
towards up or down.
3. Press the Control knob.
Exit the detail color adjustment mode.
4 Exit Key Color Selection mode
Press the [FNC] button.
⁄
•
When you select “PRESET”, you can save the combination
of the Illumination Colors selected for each place. For
how to save Illumination Colors, refer to <Illumination
Color Preset Memory> (page 10).
|
10 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX503U
Disc Naming (DNPS)
Attaching a title to a CD.
Illumination Color Preset Recall
Recalling the selection you saved in Illumination
Color Preset mode.
1 Play the disc you want to attach a name to
2 Select Name set mode item during Menu
1 Enter Audio Preset Recall mode
Select “COLOR” > “PRESET” > “RECALL”.
For how to select Function Control item, refer to
<Function Control> (page 6).
mode
Select the “Name Set” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Recall the Illumination Color Preset
Press the Control knob.
“Recall?” is displayed.
3 Enter Name set mode
Press the Control knob for at least 1 second.
4 Enter the name
Operation type
Move the cursor to the enter
character position
3 Turn the Control knob to select “YES”, and then
press the Control knob.
“Recall Completed” is displayed.
Operation
Push the Control knob towards right
or left.
4 Exit Illumination Color Preset Recall mode
Select the character type*
Select the characters
Press the Control knob.
Turn the Control knob or push it
towards up or down.
Press the [FNC] button.
⁄
* Each time you press the knob, the character type
alternates between the types shown in the table below.
•
When you recall Illumination Color Preset, the current
Illumination Color settings will be replaced with the
preset selection.
Character type
Alphabet upper case
Alphabet lower case
Numbers and symbols
Special characters (Accent characters)
⁄
•
Enter characters by using a remote control with numbers
buttons.
Example: If you are entering “DANCE”.
“D”
[3]
1
“A”
[2]
1
“N”
[6]
2
“C”
[2]
3
“E”
[3]
2
Character
Button
Times pressed
[
¢
]
[
¢
]
[
¢
]
[
¢
]
5 Exit Menu mode
Press the [FNC] button.
⁄
•
•
A title cannot be attached to Audio file media.
When operation stops for 10 seconds the name at that
time is registered, and Name Set mode closes.
Media that you can attach a name to
- Internal CD player: 10 discs
•
- External CD changer/ player: Varies according to the
CD changer/ player. Refer to the CD changer/ player
manual.
•
You can change the name of a CD by the same
operation you used to name it.
English
|
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Auxiliary Input Display Setting
Opening message edit
Selects the display below when changing to
Auxiliary input source.
Setting the opening message to be displayed when
the power is turned on.
1 Select Auxiliary input display setting item
during Menu mode (In AUX mode)
Select the “Name Set” display.
1 Select Opening message edit item during
Menu mode
Select “OPENING MSGE Edit”.
For how to select Function Control items, refer to
<Function Control> (page 6).
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
2 Enter Opening message edit mode
Press the Control knob for at least 1 second.
3 Enter the character
Operation type
Operation
3 Select the Auxiliary input display
Turn the Control knob or push it towards up or
down.
Move the cursor to the enter
character position
Push the Control knob towards right
or left.
Select the character type*
Select the characters
Press the Control knob.
Turn the Control knob or push it
towards up or down.
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
4 Exit Auxiliary input display setting mode
* Each time you press the knob, the character type
alternates between the types shown in the table below.
Press the [FNC] button.
⁄
Character type
Alphabet upper case
Alphabet lower case
Numbers and symbols
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
•
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is
displayed by default.
4 Press the Control knob for at least 2 seconds.
“Completed” is displayed.
5 Exit Menu mode
Press the [FNC] button.
⁄
•
The Opening message can be displayed up to 8
characters.
|
12 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Music disc/Audio file Operation
Function of Audio file/ Internal CD source
Function of remote control
Music Select
Direct Music Search
Selecting the music you want to listen to from the
device or media being played now.
Searchs the music by entering the track number.
1 Enter the music number
Press the number buttons on the remote
control.
1 Enter Music Select mode
Turn the Control knob.
The music list is displayed.
2 Search the music
2 Search for music
Press the [4] or [¢] button.
Select the category item using the Control
knob.
Cancelling Direct Music Search
Press the [38] button.
iPod source (when “iPod Mode” is “ON”)
(Function of DPX503U)
⁄
•
Direct Music Search cannot be performed during playing
of iPod, “Music Editor” media, Random play, or scan play.
Operation type
Operation
Movement between items Turn the Control knob.
Selection of item
Press the Control knob.
Return to previous item
Return to first item
Push the Control knob towards up.
Push the Control knob towards up for at
least 1 second.
Function of disc changers with remote control
Direct Disc Search
Searchs the disc by entering the disc number.
Other source
Audio file (including iPod source while “iPod
Mode” is “OFF”)
1 Enter the disc number
Press the number buttons on the remote
control.
Operation type
Operation
Movement between items Turn the Control knob or push it towards
2 Search the disc
up or down.
Press the [FM] or [AM] button.
Selection of item
Return to previous item
Return to first item
Push the Control knob towards right.
Push the Control knob towards left.
Push the Control knob towards left for at
least 1 second.
Cancelling Direct Disc Search
Press the [38] button.
⁄
Internal CD source
•
Direct Disc Search cannot be performed during playing
of Random play or scan play.
Operation type
Operation
Movement between track Turn the Control knob or push it towards
up or down.
Selection of track
Press the Control knob.
Return to first track
Push the Control knob towards left for at
least 1 second.
The “2” or “3” symbol shown beside the displayed
item indicates that the item is preceded or followed
by another item.
Selecting a music will play it from the beginning.
Cancelling Music Select
Press the [FNC] button.
⁄
•
•
Music Select cannot be performed during Random play.
Set the iPod mode in “MENU” > “iPod Mode” of
<Function Control> (page 6).
English
|
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Music disc/Audio file Operation
Basic Operation of Disc Changer
(Optional)
Selecting CD changer source
Press the [SRC] button.
Select the “CD Changer” display.
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
Music search
Push the Control knob towards right or left.
Disc Search
Push the Control knob towards up or down.
Playing the Current Song or Disc Repeatedly.
(Repeat play)
Press the [4] button.
Pressing the button repeatedly selects Track Repeat
play on (“Track Repeat ON”), Disc Repeat play on
(“Disc Repeat ON”), and Repeat play off (“Repeat
OFF”) sequentially.
Randomly plays the music in the disc changer.
(Magazine random play)
Press the [6] button.
Pressing the button toggles the setting between
Magazine random play on (“Magazine RDM ON”)
and off (“Magazine RDM OFF”).
|
14 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
Function of remote control
Station Preset Memory
Putting a station in the memory.
Direct Access Tuning
Entering the frequency and tuning.
1 Select the frequency to put in the memory
Push the Control knob towards right or left.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
2 Enter Preset Memory mode
Select “P.MEM”.
For how to select Function Control item, refer to
“– – – –” is displayed.
<Function Control> (page 6).
2 Enter the frequency
Press the number buttons on the remote
3 Select the number to put in the memory
control.
Example:
Turn the Control knob.
4 Determine the number to put in the memory
Desired frequency Press button
Press the Control knob.
92.1 MHz (FM)
[0], [9], [2], [1]
5 Allow the determined number to take effect
810 kHz (AM)
[0], [8], [1], [0]
Press the Control knob.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
Cancelling the Preset Memory mode
Press the [FNC] button.
⁄
⁄
•
This function can be operated with [1] — [6] button.
Refer to <Basic operation> (page 4).
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
Preset Tuning
Recalling the stations in the memory.
Changing Language for PTY Function
Selecting the Program Type display language as
follows;
1 Enter Preset Tuning Select mode
Turn the Control knob.
A station list is displayed.
Language
English
Spanish
French
Display
“English”
“Spanish”
“French”
“Dutch”
Language
Norwegian
Portuguese
Swedish
Display
“Norwegian”
“Portuguese”
“Swedish”
“German”
2 Select a desired station in the memory
Turn the Control knob.
Dutch
German
3 Recall the station
Press the Control knob.
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 16).
Cancelling Preset Tuning
Press the [FNC] button.
2 Enter Changing Language mode
Press the [TI] button.
⁄
•
This function can be operated with [1] — [6] button.
Refer to <Basic operation> (page 4).
3 Select the language
Turn the Control knob or push it towards up or
down.
4 Exit Changing Language mode
Press the [TI] button.
English
|
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner Operation
PTY (Program Type)
Program Type preset
Selecting the Program Type below and searching
for a station;
Putting the Program Type in the Preset button
memory and quick recall.
Program Type Display
Program Type Display
Presetting the Program Type
Speech
Music
News
“All Speech”
“All Music”
“News”
Weather
“Weather &
Metr”
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 16).
Finance
Children’s
programs
“Finance”
“Children's
Prog”
Current Affairs “Current Affairs”
2 Enter Program Type preset mode
Information
Sport
“Information”
“Sport”
Press the [FNC] button.
Social Affairs “Social Affairs”
3 Select the number you want to put in the
Religion
Phone In
Travel
“Religion”
“Phone In”
“Travel &
Touring”
Education
Drama
“Education”
“Drama”
memory
Turn the Control knob or push it towards left
or right.
Culture
“Cultures”
Science
“Science”
Leisure
“Leisure &
Hobby”
Varied
Pop Music
Rock Music
“Varied Speech”
“Pop Music”
“Rock Music”
4 Preset the Program Type
Press the Control knob for at least 1 second.
Jazz Music
“Jazz Music”
Country Music “Country Music”
National Music “National
Music”
5 Exit Program Type preset mode
Easy Listening “Easy Listening
Music M”
Light Classical “Light Classic
M”
Serious Classical “Serious
Classics”
Press the [FNC] button.
Recalling the preset Program Type
Oldies Music “Oldies Music”
Folk Music
“Folk Music”
1 Enter PTY mode
Documentary “Documentary”
Refer to <PTY (Program Type)> (page 16).
Other Music
“Other Music”
2 Enter Program Type preset mode
•
Speech and Music include the Program type shown
below.
Press the [FNC] button.
3 Select the number you want to recall from the
Music: Black character item.
Speech: White character item.
memory
Turn the Control knob or push it towards left
or right.
1 Enter PTY mode
Press the Control knob.
“PTY Select” is displayed.
4 Recall the Program Type
Press the Control knob.
2 Select the Program Type
Turn the Control knob or push it towards up or
down.
5 Exit Program Type preset mode
Press the [FNC] button.
3 Search for the selected Program Type station
Push the Control knob towards right or left.
4 Exit PTY mode
Press the Control knob.
⁄
•
This function cannot be used during a traffic bulletin or
AM reception.
•
When the selected Program Type is not found, “No PTY”
is displayed. Select another Program Type.
|
16 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Activating Security Code
Deactivating Security Code
To deactivate the Security Code function.
⁄
•
You can set the Security Code with a 4 digit number of your
choice.
1 Select Security Code item during Menu
mode (In Standby mode)
Select the “Security Clear” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
•
The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
1 Select Security Code item during Menu
mode (In Standby mode)
“Security Set” is displayed.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When “Enter” is displayed, “SECURITY CLEAR” is also
displayed.
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When “Enter” is displayed, “SECURITY SET” is also
displayed.
3 Enter Security Code
Operation type
Select the digits to enter
Operation
Push the Control knob towards right
or left.
Turn the Control knob or push it
towards up or down.
3 Enter Security Code
Select the Security Code
numbers
Operation type
Operation
Select the digits to enter
Push the Control knob towards right
4 Press the Control knob for at least 3 seconds.
“Clear” is displayed.
The Security Code function deactivates.
or left.
Select the Security Code
numbers
Turn the Control knob or push it
towards up or down.
5 Exit Security Code mode
4 Confirm the Security Code
Press the [FNC] button.
Press the Control knob for at least 3 seconds.
When “Re-Enter” is displayed, “SECURITY SET” is also
displayed.
⁄
•
If a wrong security code is entered, “Error” is displayed.
Enter a correct security code.
5 Do the step 3 through 4 operation, and reenter
the Security Code.
“Approved” is displayed.
The Security Code function activates.
⁄
•
If you enter the wrong Code in steps 3 through 4, repeat
from step 3.
6 Exit Security Code mode
Press the [FNC] button.
Entering Security Code
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
1 Turn the power ON.
2 Do the step 3 through 4 operation, and enter
the Security Code.
“Approved” is displayed.
Now, you can use the unit.
English
|
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Manual Clock Adjustment
Demonstration mode setting
Turning the demonstration mode ON/OFF.
1 Select Clock Adjustment item during Menu
mode
Select the “Clock Adjust” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
1 Select Demonstration item during Menu mode
Select the “DEMO Mode” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Enter Clock adjustment mode
Press the Control knob for at least 1 second.
The clock display blinks.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds.
Pressing this button for 2 seconds or longer toggles
the setting between “ON” and “OFF”.
3 Adjusting Clock
3 Exit Demonstration mode
Operation type
Selecting the item (hours or
minutes)
Operation
Push the Control knob towards right
or left.
Press the [FNC] button.
Adjust each item
Turn the Control knob or push it
towards up or down.
When LX AMP unit connecting
4 Exit Clock adjustment mode
AMP Control
You can control the LX AMP connected to the unit.
Press the [FNC] button.
⁄
•
You can do this adjustment when “MENU” > “SYNC” in
1 Select AMP Control item during Menu mode
Select the “AMS Control” display.
<Function Control> (page 6) is set to “OFF”.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Enter AMP Control mode
Date Adjustment
Press the Control knob for at least 1 second.
3 Select the AMP Control item for adjustment
1 Select Date Adjustment item during Menu
mode
Push the Control knob towards up or down.
Select the “Date Adjust” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
⁄
•
For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
2 Enter Date adjustment mode
Press the Control knob for at least 1 second.
The date display blinks.
4 Adjust the AMP Control item
Push the Control knob towards right or left.
5 Exit AMP Control mode
3 Adjusting Date
Press the [FNC] button.
Operation type
Operation
Selecting the item (month, day, Push the Control knob towards right
or year)
or left.
Adjust each item
Turn the Control knob or push it
towards up or down.
4 Exit Date adjustment mode
Press the [FNC] button.
|
18 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Function of DPX503U
Function of DPX503U
Cabin selection
DTA (Digital Time Alignment) setting
You can compensate the delay of the sound arrival
time, which is caused by the installation position of
the speakers, by selecting your environment from
the following car types;
Adjusting fine tuning of the speaker position
compensation value specified at <Cabin selection>
(page 19).
1 Enter DTA setting mode
Car type (rear speaker position)
Not compensating.
Display
“OFF”
Select “SOUND” > “S-SET” > “DTA”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Compact car (rear door)
Compact car (cargo)
Sedan (rear door)
“Compact1”
“Compact2”
“Sedan1”
“Sedan2”
“Wagon1”
“Wagon2”
“Minivan1”
“Minivan2”
“SUV1”
2 Select the speaker you want to set
Sedan (cargo)
Setting speaker
Front speaker
Rear speaker
Subwoofer
Display
Station wagon (rear door)
Station wagon (cargo)
Minivan (rear door)
“DTA-Front”
“DTA-Rear"
“DTA-Sub"
Minivan (cargo)
Turn the Control knob and push the center
when the desired item is displayed.
Sport-utility vehicle (rear door)
Sport-utility vehicle (cargo)
Passenger van (rear door)
Passenger van (cargo)
“SUV2”
“PassengerVan1”
“PassengerVan2”
“User”
3 Set the compensation value of the speaker
position
Turn the Control knob.
Calls the value adjusted at <DTA> (page 19).
Adjust between 0 and 440 cm.
Refer to <Appendix> (page 29) on how to set the
compensation value.
1 Enter Cabin select mode
Select “SOUND” > “S-SET” > “CABIN”.
For how to select Function Control item, refer to
<Function Control> (page 6).
4 Exit DTA setting mode
Press the [FNC] button.
2 Select the car type
Turn the Control knob and push the center
when the desired item is displayed.
3 Exit Cabin select mode
Press the [FNC] button.
⁄
•
You can compensate the distances in more details by
using <DTA> (page 19) function.
In addition, the value specified at <DTA> can be called
by selecting “User”.
English
|
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Function of DPX503U
2 Select the item you want to set
Turn the Control knob and push the center
when the desired item is displayed.
X’Over setting
You can set a X’Over value for the speakers;
3 Set the value
Adjustment Item Display
Front High Pass Filter “HPF-Front”
Range
Through/40/60/80/100/120/
150/180/220 Hz
Through/40/60/80/100/120/
150/180/220 Hz
Turn the Control knob.
4 Exit Equalizer Control mode
Rear High Pass Filter “HPF-Rear”
Press the [FNC] button.
Low Pass Filter
“LPF”
50/60/80/100/120/Through
Hz
Subwoofer level
Subwoofer Phase
“SUB-W LEVEL” –15 — +15
“SW PHASE” Reverse (180°)/ Normal (0°)
Function of DPX503U
Preset position selection
According to the listening position, select the
position from the following settings so that the
normal position of the sound environment can
be compensated in accordance with the selected
position;
1 Enter X’Over setting mode
Select “SOUND” > “S-SET” > “XOVER”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Select the item you want to set
Turn the Control knob and push the center
when the desired item is displayed.
Compensation seat
Not compensating.
Front-Left seat
Range
“All”
“FrontLeft”
“FrontRight”
“FrontAll”
“USER”
3 Set the X’Over value
Front-Right seat
Front seat
Turn the Control knob.
4 Exit X’Over setting mode
Calls the value adjusted at <Manual position
setting> (page 21).
Press the [FNC] button.
1 Enter Position setting mode
Select “SOUND” > “S-CTRL” > “POSIT” > “P-POSI”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Function of DPX503U
Equalizer Control
You can adjust following Equalizer Control items ;
2 Select the seat you want to compensate
Turn the Control knob.
Adjustment Item Display
Range
System Q
“Preset EQ”
“NATURAL”(Natural)/“USER”
(User setting)/“ROCK”(Rock)/
“POPS”(Pops)/“EASY”(Easy)/
“TOP40”(Top 40)/“JAZZ”
(Jazz)/ ”GAME”(Game)
–8 — +8
3 Exit Position setting mode
Press the [FNC] button.
Bass level*
“Bass”
Middle level*
Treble level*
“Middle”
“Treble”
–8 — +8
–8 — +8
* Source tone memory: Puts the set up value in the
memory per source.
⁄
•
“USER”: The ranges selected lastly for Bass level, Middle
level, and Treble level are recalled automatically.
1 Enter Equalizer Control mode
Select “SOUND” > “S-CTRL” > “EQ”.
For how to select Function Control item, refer to
<Function Control> (page 6).
|
20 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of DPX503U
Function of DPX503U
Manual position setting
Audio Preset Memory
Making fine adjustment of the value specified at
Preset position selection per speaker.
Registering the value setup by Sound Control. The
memory cannot be erased by the Reset button.
1 Enter Position setting mode
Select “SOUND” > “S-CTRL” > “POSIT” >
“M-POSI”.
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
For how to select Function Control item, refer to
- Cabin selection (page 19)
<Function Control> (page 6).
- DTA (Digital Time Alignment) setting (page 19)
- X’Over setting (page 20)
- Equalizer Control (page 20)
- Preset position selection (page 20)
- Manual position setting (page 21)
2 Select the speaker you want to adjust
Item
Setting overview
Front Left speaker
Front Right speaker
Rear Left speaker
Rear Right speaker
Subwoofer Left
“Front Lch”
“Front Rch”
“Rear Lch”
“Rear Rch”
“Sub Lch”
“Sub Rch”
2 Enter Audio Preset Memory mode
Select “SOUND” > “PRESET” > “MEMO”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Subwoofer Right
3 Put the Audio Preset in the memory
Press the Control knob.
“Memory?” is displayed.
Turn the Control knob and push the center
when the desired item is displayed.
3 Adjust the speaker
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Memory Completed” is displayed.
Turn the Control knob.
Adjust between 0 and 170 cm.
4 Exit Position setting mode
5 Exit Audio Preset mode
Press the [FNC] button.
Press the [FNC] button.
⁄
⁄
•
•
When you select “User” at <Preset position selection>
(page 20), the adjusted setting value will be recalled.
Register 1 pair of Audio Preset Memory. You cannot
register by the source.
•
When you press the Reset, all the sources will be the
setting value which is registered.
English
|
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Function of DPX503U
Audio Control
You can adjust following Audio Control items ;
Audio Preset Recall
Recalling the sound setup registered by <Audio
Preset Memory> (page 21).
Adjustment Item Display
Rear volume “REAR VOLUME” 0 — 35
Subwoofer level* “SUB-W LEVEL” –15 — +15
Range
1 Select the source
System Q*
“NATURAL”/
Natural/User setting/Rock/
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
“USER”/“ROCK”/ Pops/Easy/Top 40/Jazz/Game
“POPS”/“EASY”/
“TOP40”/“JAZZ”/
”GAME”
2 Enter Audio Preset Recall mode
Select “SOUND” > “PRESET” > “RECALL”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Bass level*
Middle level*
Treble level*
Balance
“BASS LEVEL”
“MIDDLE LEVEL” –8 — +8
“TREBLE LEVEL” –8 — +8
“BALANCE”
“FADER”
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
3 Recall the Audio Preset
Press the Control knob.
“Recall?” is displayed.
Fader
Exit Audio Control mode (Volume control mode)
*Function of DPX303/DPX313.
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Recall Completed” is displayed.
⁄
•
Source tone memory: You can set Bass, Middle, and
Treble for each source.
•
“USER”: The ranges selected lastly for Bass level, Middle
level, and Treble level are recalled automatically.
5 Exit Audio Preset Recall mode
Press the [FNC] button.
1 Select the source to adjust
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
⁄
•
The User memory of “SYSTEM Q” in <Equalizer Control>
(page 20) is changed to the value which was recalled.
The source tone memory item of <Equalizer Control>
(page 20) is changed to the value which was recalled by
the selected source.
•
2 Enter Audio Control mode
Press the [AUD] knob.
3 Select the Audio item to adjust
Press the [AUD] knob.
4 Adjust the Audio item
Turn the [AUD] knob.
5 Exit Audio Control mode
Press any button.
Press a button other than the [AUD] knob or [0]
and [ATT] button.
|
22 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Setup
Speaker Setting
You can set Sound system , such as follows;
Fine-tuning so that the System Q value is optimal
when setting the speaker type as follows;
Adjustment Item Display
Range
Front High Pass Filter* “HPF-F”
Through/40/60/80/100/120/
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
“OFF”
“5/4inch”
“6x9/6inch”
“O.E.M.”
150/180/220 Hz
Rear High Pass Filter* “HPF-R”
Through/40/60/80/100/120/
150/180/220 Hz
50/60/80/100/120/Through
Hz
Low Pass Filter*
“LPF”
Subwoofer Phase* “SW PHASE” Reverse (180°)/ Normal (0°)
1 Enter Standby
Volume offset
Loudness*
Dual Zone System
“VOL-OFFSET” –8 — 0 (AUX: -8— +8)
Select the “STANDBY” display.
“LOUD”
OFF/ON
OFF/ON
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
“2 ZONE”
*Function of DPX303/DPX313.
⁄
2 Enter Speaker Setting mode
Press the [AUD] knob.
“SP SEL” is displayed.
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
•
Loudness: Compensates for low and high tones during
low volume. (Only the low tone is compensated for
when the tuner is selected as a source.)
Dual Zone System
3 Select the Speaker type
Turn the [AUD] knob.
•
4 Exit Speaker Setting mode
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by “Zone2” of
<Function Control> (page 6).
Press the [AUD] knob.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [AUD] knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 22) or [5]/[∞] button on the remote control
(page 25).
- The Audio Control has no effect on sub source.
1 Select the source to adjust
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
2 Enter Audio Setup mode
Press the [AUD] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [AUD] knob.
4 Adjust the Audio setup item
Turn the [AUD] knob.
5 Exit Audio Setup mode
Press the [AUD] knob for at least 1 second.
English
|
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Adjustments
Function of DPX303/DPX313
Function of DPX303/DPX313
Audio Preset Memory
Audio Preset Recall
Registering the value setup by Sound Control. The
memory cannot be erased by the Reset button.
Recalling the sound setup registered by <Audio
Preset Memory> (page 24).
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- <Audio Control> (page 22)
- <Audio Setup> (page 23)
1 Select the source
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
2 Select Audio Preset item during Menu
mode (Other than Standby mode)
Select the “Audio Preset” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Select Audio Preset item during Menu
mode (Other than Standby mode)
Select the “Audio Preset” display.
For how to select Function Control items, refer to
<Function Control> (page 6).
3 Enter Audio Preset mode
3 Enter Audio Preset mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
4 Select the Audio Preset Recall
Turn the Control knob.
Select the “Recall” display.
4 Select the Audio Preset Memory
Turn the Control knob.
Select the “Memory” display.
5 Determine whether to recall the Audio Preset
Press the Control knob.
“Recall?” is displayed.
5 Determine whether to put the Audio Preset in
the memory
Press the Control knob.
“Memory?” is displayed.
6 Recall the Audio Preset
Turn the Control knob to select “YES”, and then
press the Control knob.
6 Put the Audio Preset in the memory
Turn the Control knob to select “YES”, and then
press the Control knob.
“Recall Completed” is displayed.
7 Exit Audio Preset mode
“Memory Completed” is displayed.
Press the [FNC] button.
7 Exit Audio Preset mode
⁄
•
Press the [FNC] button.
The User memory of “SYSTEM Q” in <Audio Control>
(page 22) is changed to the value which was recalled.
The source tone memory item of <Audio Control> (page
22) is changed to the value which was recalled by the
selected source.
⁄
•
•
•
•
Register 1 pair of Audio Preset Memory. You cannot
register by the source.
When you press the Reset, all the sources will be the
setting value which is registered.
The following items cannot be registered.
Volume, Balance, Fader, Loudness, Volume offset, Dual
Zone System, Rear Volume
|
24 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory of DPX503U/DPX313
Basic Operations of remote control
In Tuner source
SRC
ATT
VOL
AUD
SRC
AT T
Band select
[FM]/[AM]
VOL
AUD
Station select
[4]/[¢]
Recall preset stations
[1] — [6]
FM/AM
2-ZONE
0 — 9
DIRECT
(page 15)
In CD/USB source
Music select
[4]/[¢]
Folder/Disc select
Pause/Play
[FM]/[AM]
[38]
⁄
About [
]
General control
This button is used when Bluetooth HANDS FREE
BOX is connected. For more information, refer to the
instruction manual of Bluetooth HANDS FREE BOX.
Volume control
Source select
[VOL]
[SRC]
[ATT]
¤
• Do not set the remote control in hot places such as
on the dashboard.
Volume reduce
In Audio control
Loading and Replacing battery
Use two “AA”/ “R6”-size batteries.
Slide the cover while pressing downwards to remove
it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
Audio item select
[AUD]
[VOL]
Adjusts the Audio item
⁄
•
Refer to <Audio Control> (page 22) for the operation
method, such as the procedures for Audio control and
others operations.
Dual Zone control
Dual zone system on and off
Rear channel volume control
[2-ZONE]
[ 5]/ [∞]
English
|
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
About Audio file
About USB device
•
•
•
•
•
Playable Audio file
• If you start playback after connecting the iPod, the
music that has been played by the iPod is played
first.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
USB device Playable Model
DPX503U
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
In this case, “RESUMING” is displayed without
displaying a folder name, etc. Changing the browse
item will display a correct title, etc.
• When the iPod is connected to this unit,
“KENWOOD” or “✓” is displayed on the iPod to
indicate that you cannot operate the iPod.
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
•
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
Folder
Audiofile
CD
(ꢂ)
:
vꢀ
ꢁ
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
ꢃ
vꢆ
vꢇ
ꢅ
vꢄ
ꢈ
vꢉ
v.
About KENWOOD “Music Editor” of PC
application
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
• “Music Editor” is recorded in the CD-ROM attached
to this unit.
• Refer to the user’s manual recorded in the
installation CD-ROM and Help of “Music Editor” for
the operation method of “Music Editor”.
• The unit can play USB device created by “Music
Editor”.
⁄
•
In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
• Information about “Music Editor” upgrade is put on
•
The word “iPod” appearing in this manual indicates the
iPod connected with the iPod connection cable (optional
accessory). The iPod connected with the iPod connection
cable can be controlled from this unit. iPods that can be
connected with the iPod connection cable are the iPod
nano, Fifth Generation iPod, iPod classic, and iPod touch.
Other iPods cannot be connected.
|
26 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
For operating KCA-BT100 (Optional)
However, the following control methods of the
function for this unit may be different from the
Instruction manual; therefore, refer to the following
supplemental instruction.
<Deleting a Registered Cell-Phone>
1–3. Operation is the same. Refer to the instruction
manual of KCA-BT100.
4. Press the Control knob.
5. Select “YES” using the Control knob.
6. Press the Control knob.
7. Press the [FNC] button.
<Menu System>
For how to operate Menu, refer to <Function
Control> in this instruction manual.
About display
Function Control Glossary
•
SRC Select
Setting up the Source Select mode.
1 : Displays source icons for your choice.
2 : Allows you to select sources one after another.
Display
•
If this unit is not operated at least 5 seconds with
“OFF” selected, the display turns off. During a setup
mode, the display will not turn off even if 5 seconds
lapse.
•
•
ILM Dimmer (illumination dimmer)
Reduces the key Illumination brightness.
AUTO: Dims the illumination in conjunction with
the Light switch of the vehicle.
MNAL: Dims the illumination constantly.
OFF: Does not dim the illumination.
AT COL CHG (Automatic illumination color
change)
Cell-Phone Status is displayed in the status display of
this unit.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
Selecting “iPod” changes the key illumination
automatically according to the color of the iPod
body during playback of the iPod source.
* The color of key illumination is only a
recommended color by our campany. It does not
necessarily match the body color of iPod.
Compatible iPod models:
iPod (5th generation), iPod classic, iPod touch,
iPod nano (1st/2nd/3rd generation),
Fifth Generation iPod (iPod with video)
Displays of KCA-BT100 Instruction Actual displays on this unit
Manual
“Disconnect”
“HF Disconnect”
“Connect”
“HF Connect”
“Phone Delete”
“Phone Status”
“Device Delete”
“BT DVC Status”
BT : Displays the bluetooth connection status.
This indicator turns on when a cell-phone is
connected to this unit.
•
•
SWPRE (Switching Preout)
Switches the preout between rear output (“Rear”)
and subwoofer output (“Sub-W”).
AMP
Selecting “OFF” turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
Selecting “OFF” disables the functions of the Dual
Zone and KCA-BT100 (optional accessory) because
no sound will be output from the front speakers.
•
•
Zone2 (Dual Zone)
Set the destination (front speaker “Front” or rear
speaker “Rear”) of the sub source (AUX IN) when the
Dual Zone function is turned on.
Supreme
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate (less
than 128Kbps, Sampling frequency is 44.1kHz).
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
English
|
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
•
News (News Bulletin with Timeout Setting)
Automatically receives news bulletin when it
starts. Set the time during which interrupt is to be
disabled after start of another news bulletin.
Changing “News 00min” to “News 90min” turns this
function ON.
If news bulletin starts when this function is ON,
“Traffic INFO” is displayed and news is received. If
“20min” is has been set, reception of another news
bulletin will not start for 20 minutes.
The news bulletin volume is the same level that
was set for Traffic Information.
Seek Mode (Tuning mode select)
Select a tuning mode of the radio.
•
DISP REVERSE
Switches the panel display between positive
or negative. In addition, you can reverse it in
conjunction with the interior light.
POSI 1 : Displays the text in the positive.
POSI 2 : When the interior light is off, the text is
displayed in the positive; when the interior
light is on, the text is displayed in the
negative.
NEGA 1 : Displays the text in the negative.
NEGA 2 : When the interior light is off, the text
is displayed in the negative; when the
interior light is on, the text is displayed in
the positive.
•
Tuning mode
Auto seek
Display Operation
“Auto1” Automatic search for a station.
•
Cabin
The position of front and rear speakers may not
have the same distance from the center of the
vehicle interior.
For example, when a car type has the front speaker
nearer to the center of the vehicle interior than the
rear speaker, you hear a delayed sound from the
rear speaker.
This function allows the sound of the nearer
speaker to the center of the vehicle interior to be
output with delays and compensates the sound
arrival time from the front and rear speakers to be
heard at the same time.
The sound arrival time can be compensated simply
by selecting the car type you want to use, because
the compensation values for typical cars have been
preset.
Preset station seek “Auto2” Search in order of the stations in the
Preset memory.
Manual
“Manual” Normal manual tuning control.
•
•
•
AF (Alternative Frequency)
When the reception is poor, automatically alternate
to another frequency broadcasting the same
program in the same RDS network with better
reception.
Russian (Russian language setting)
When this is set to ON, the following character
strings are displayed in Russian:
Folder name/ File name/ Song title/ Artist name/
Album name/ KCA-BT100 (optional accessory)
Power OFF (Power OFF Timer)
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
– – –: Power OFF Timer function is OFF.
20min: Turns the power OFF after 20 minutes.
(Factory setting)
You can specify the more suitable compensation
values for your vehicle by using <DTA> (page 19)
function.
You can also compensate the listening positions
(such as front and rear) in accordance with scenes
by specifying the positions at <Preset position
selection> (page 20).
40min: Turns the power OFF after 40 minutes.
60min: Turns the power OFF after 60 minutes.
CD Read
•
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
|
28 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
•
DTA (Digital Time Alignment)
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
Make fine adjustment of the delay time of the
speaker output specified at <Cabin selection>
(page 19) to have a more suitable environment for
your vehicle.
Information on Disposal of Old Electrical
and Electronic Equipment and Batteries
(applicable for EU countries that have
adopted separate waste collection systems)
Products and batteries with the symbol
(crossed-out wheeled bin) cannot be
disposed as household waste.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
Old electrical and electronic equipment
and batteries should be recycled at a facility
capable of handling these items and their
waste byproducts.
2 Measure the distances from the reference point
to the speakers.
Contact your local authority for details in
locating a recycle facility nearest to you.
Proper recycling and waste disposal will
help conserve resources whilst preventing
detrimental effects on our health and the
environment.
3 Calculate the distance difference in accordance
with the farthest speaker.
+100cm
Notice: The sign "Pb" below the symbol for
batteries indicates that this battery
contains lead.
FRONT
REAR
FRONT
50cm
80cm
The marking of products using lasers
(Except for some areas)
REAR
150cm
+70cm
CLASS 1
LASER PRODUCT
+0cm
SUB-W
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
English
|
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/ Installation Procedure
Accessories
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
1
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
..........1
..........2
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“Protect” is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
2
•
•
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
•
•
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
•
•
•
•
•
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
•
•
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
About CD players/disc changers connected
to this unit
If the CD player/ disc changer has the “O-N” switch, set
it to the “N” position.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
|
30 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
To External Display/ Steering remote
FM/AM antenna input (JASO)
Front preout
Rear/SubWoofer preout
Fuse (10A)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant instruction manuals.
⁄
Wiring harness
(Accessory1)
TEL mute wire (Brown)
Connect to the terminal that is grounded when
either the telephone rings or during conversation.
MUTE
To connect the Kenwood navigation system,
⁄
consult your navigation manual.
If no connections are made, do not
let the wire come out from the tab.
Power control/ Motor antenna
control wire (Blue/White)
P.CONT
Connect either to the power control terminal
when using the optional power amplifier, or to the
antenna control terminal in the vehicle.
ANT.CONT
Battery wire (Yellow)
Ignition wire (Red)
⁄
See next page.
A–7 Pin (Red)
A–4 Pin (Yellow)
8
7
6
5
4
3
2
1
Connector A
Connector B
8
7
6
5
4
3
2
1
English
|
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
External Power
Connector
2WARNING
Functions
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
A-5
A-6
A-7
A-8
Yellow
Battery
Power Control
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2,
make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
Blue/White
Orange/White
Red
Black
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and the A-
4 pin (yellow) is connected to the constant power
supply.
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
B-8
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
Ignition cable
A-7 Pin (Red)
(Red)
Unit
Vehicle
A-4 Pin (Yellow)
Battery cable
(Yellow)
|
32 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation/Removing the Unit
Installation
Removing the hard rubber frame
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Accessory2
Bend the tabs of the mounting sleeve with
a screwdriver or similar utensil and attach it
in place.
2 When the upper level is removed, remove the
lower two locations.
⁄
⁄
•
The frame can be removed from the bottom side in the
same manner.
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
Removing the Unit
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Insert the two removal tools deeply into the slots
on each side, as shown.
3 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Accessory2
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
4 Pull the unit all the way out with your hands, being
careful not to drop it.
English
|
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• Cannot set up the High Pass Filter.
• Cannot set up the Fader.
General
• No Audio control effect on AUX.
• Cannot set up the subwoofer position of Manual
position setting.
? The Touch Sensor Tone does not sound.
✔
The preout jack is being used.
☞
The Touch Sensor Tone cannot be output from
the preout jack.
• Preout is not set to subwoofer. ☞ “MENU” >
“SWPRE” of <Function Control> (page 6)
• <Subwoofer output> of <Basic Operation> (page 4)
is not set to On.
• The Dual zone function is enabled. ☞ <Audio
? The illumination flashes when the knob or button
is operated.
✔
This is the key illumination effect.
☞
You set this effect in “MENU” > “ILM Effect” of
Setup> (page 23)
<Function Control> (page 6).
!
!
• Cannot set up the subwoofer phase.
The Low Pass Filter is set to Through. ☞ <Audio
Setup> (page 23), <X’Over setting> (page 20)
? The key illumination effect brought about in
conjunction with the sound volume is small.
✔
The key illumination effect may be insufficient
depending on the sound volume and sound quality.
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 23)
Tuner source
? Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
!
• Cannot register a security code.
• Cannot set up Display Illumination Control.
• Cannot set up the Power-off timer.
<Demonstration mode Setting> (page 18) is not
turned off.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
☞
Clean the CD, referring to the CD cleaning of the
section on <Handling CDs> (page 3).
The disc is loaded in a different slot from that
specified.
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
Audio file source
? The sound skips when an Audio file is being
played.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
The recording condition is bad.
Record the media again or use another media.
☞
? Noise is heard when carrying out Folder Search.
✔
Noise may be produced if folders without audio files
exist continuously in the playing media.
☞
Do not make folders without audio files.
|
34 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
USB ERROR (Blink):
Some trouble may have occurred to the
The messages shown below display your
systems condition.
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
TOC Error:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
iPod Error:
Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 26) for information on supported
iPods.
➪ Remove the USB device and then
reconnect it.
Error 05:
Error 77:
The disc is unreadable.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
“Error 77” code does not disappear, consult
your nearest service center.
➪ Confirm that the software for the iPod is
the latest version.
Mecha Error/ Mecha ERR:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the “Mecha
Error” code does not disappear, consult
your nearest service center.
USB REMOVE: The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
IN (Blink):
Protect:
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
Unsupported File:
An Audio file is played with a format that this
unit can’t support.
Copy Protect/ Copy Protection/ COPY PRO:
A copy-protected file is played.
Read Error:
The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
An unsupported USB device is connected.
No Music Data/ No Music/ Error 15:
• The connected USB device contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
English
|
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
FM tuner section
USB Interface (DPX503U)
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
USB Standard
: USB1.1/ 2.0
Usable sensitivity (S/N = 26dB)
: 0.7 μV/75 Ω
Quieting Sensitivity (S/N = 46dB)
: 1.6 μV/75 Ω
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 65 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
Selectivity (DIN) ( 400 kHz)
: ≥ 80 dB
AAC decode
: AAC-LC “.m4a” files
Stereo separation (1 kHz)
: 35 dB
Audio section
Maximum output power
: 50 W x 4
MW tuner section
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Full Bandwidth Power (PWR DIN45324, +B=14.4V)
: 30 W x 4
Usable sensitivity (S/N = 20dB)
Speaker Impedance
: 25 μV
: 4 – 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (CD)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
LW tuner section
Frequency range
: 153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB)
: 45 μV
CD player section
Laser diode
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
General
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Operating voltage (11 – 16V allowable)
: 14.4 V
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 105 dB
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 112 x 160 mm
Dynamic range
: 93 dB
Weight
: 1.6 kg
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
Specifications subject to change without notice.
|
36 DPX503U/DPX303/DPX313
Download from Www.Somanuals.com. All Manuals Search And Download.
|