Kawasaki Drill 691170 User Manual

COMPONENT  
#691170  
14.4V BATTERY-OPERATED DRILL  
INSTRUCTION MANUAL  
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,  
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND  
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO  
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.  
FOR CUSTOMER SERVICE  
POUR LE SERVICE APRÉS VENTE  
OU DU CONSOMMATEUR  
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE  
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE  
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION  
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE  
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE  
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.  
YOUR FEEDBACK IS VITAL TO US.  
PARA EL SERVICIO  
PARA EL CONSUMIDOR  
87-1904-60957  
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,  
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.  
CONSUMER INQUIRES SHOULD BE DIRECTED TO:  
1-800-590-3723  
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.  
1431 VIA PLATA  
Printed in China  
Imprimé dans la Chine  
Impreso en China  
LONG BEACH, CA 90810-1462 USA  
691170 – 14.4V Black Cordless Drill_Rev 11/21/06  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WORK AREA  
DANGER  
indicates an imminently hazardous  
situation which, if not avoided, will result in death  
or serious injury.  
Keep your work area clean and well lit.  
areas may cause accidents or injury.  
Cluttered work benches and dark work  
WARNING  
indicates a potentially hazardous  
situation which, if not avoided, could result in  
death or serious injury.  
Do not operate power tools in explosive areas, such as in the presence of  
flammable liquids, gases or dust.  
the dust or fumes.  
Power tools create sparks which may ignite  
CAUTION  
indicates a potentially hazardous  
situation which, if not avoided, may result in  
minor or moderate injury.  
Keep bystanders, children and visitors away while operating a power tool.  
Distractions can cause you to lose control.  
CAUTION  
used without the safety alert symbol  
indicates a potentially hazardous situation which,  
if not avoided, may result in property damage.  
ELECTRICAL SAFETY  
NOTE  
provides additional information that is useful  
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord  
away from heat, oil, sharp edges, or moving parts. Replace damaged cords  
for proper use and maintenance of this tool. If a  
NOTE is indicated make sure it is fully understood.  
immediately.  
Damaged cords may create a fire.  
A battery operated tool with integral batteries or a separate battery pack  
must be recharged only with the specified charger for the battery.  
IMPORTANT SAFEGUARDS  
A charger  
that may be suitable for one type of battery may create a risk of fire when used with  
another battery.  
People with electronic devices, such as pacemakers, should consult their  
physician(s) before using this product. Operation of electrical equipment in  
close proximity to a heart pacemaker could cause interference or failure of  
the pacemaker.  
Use battery operated tool only with specifically designated battery pack.  
any other batteries may create risk of fire.  
Use of  
WARNING:  
Some dust created by power sanding, sawing, grinding, drilling and  
other construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm.  
Some examples of these chemicals are:  
• Lead from lead-based paints.  
Crystalline silica from bricks and cement and other masonry products,  
and arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this type  
of work. To reduce your exposure to these chemicals: work in a well ventilated  
area, and work with approved safety equipment, such as dust masks that are  
specially designed to filter out microscopic particles.  
WARNING:  
Handling the power cord on corded products may expose you to  
lead, a chemical known to the State of California to cause cancer and birth  
Wash hands after handling.  
defects or other reproductive harm.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
PERSONAL SAFETY  
When battery pack is not in use, keep it away from other metal objects like:  
paper clips, coins, keys, nails, screws, or other small metal objects that can  
Stay alert, watch what you are doing, and use common sense when operat-  
ing a power tool. Do not use tool while tired or under the influence of drugs,  
make a connection from one terminal to another.  
nals together may cause sparks, burns or a fire.  
Shorting the battery termi-  
alcohol or medication.  
A moment of inattention while operating power tools  
Maintain tools with care. Keep cutting tools sharp and clean  
. Properly maintained  
may result in serious personal injury.  
tools with sharp cutting edge are less likely to bind and are easier to control.  
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.  
Keep your hair, clothing, and gloves away from moving parts.  
jewelry or long hair can be caught in moving parts.  
Loose clothes,  
Check for misalignment or binding of moving parts, breakage of parts, and any  
other condition that may affect the tool’s operation. If damaged, have the tool  
serviced before using.  
Many accidents are caused by poorly maintained tools.  
Use only accessories that are recommended by the manufacturer for your  
model.  
Avoid accidental starting. Be sure switch is in the locked or OFF” position  
before inserting battery pack.  
Carrying power tools with your finger on the  
ON”  
switch or inserting battery pack into a tool with the power switch  
accidents.  
invites  
Accessories that may be suitable for one tool may create a risk of injury  
when used on another tool.  
Remove adjusting keys or wrenches before turning the tool ON.  
A wrench  
SERVICE  
or a key that is left attached to a rotating part of the tool may result in person-  
al injury.  
Tool service must be performed only by qualified repair personnel.  
maintenance by unqualified personnel may result in a risk of injury.  
Service or  
Do not overreach. Keep proper footing and balance at all times.  
Proper foot-  
ing and balance enable better control of the tool in unexpected situations.  
Use safety equipment. Always wear eye protection.  
When servicing a tool, use only identical replacement parts. Follow instructions  
in the Maintenance section of this manual.  
Dust mask, non-skid safe-  
Use of unauthorized parts or failure to  
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.  
follow Maintenance Instructions may create a risk of shock or injury.  
TOOL USE AND CARE  
SPECIFIC SAFETY RULES AND/OR SYMBOLS  
Hold tool by insulated gripping surfaces when perform-  
Use clamps or other practical ways to secure and support the workpiece to a  
ing an operation where the cutting tool may contact hidden wiring.  
Contact  
stable platform.  
Holding the work by hand or against your body is unstable and  
with a “live” wire will also make exposed metal parts of the tool live” and shock  
the operator.  
may lead to loss of control.  
Do not force tool. Use the correct tool for your application.  
The correct tool  
will do the job better and safer at the rate for which it is designed.  
SAFETY RULES FOR CORDLESS DRILL / DRIVERS  
Do not use the tool if the power switch does not turn it ON” or OFF.  
cannot be controlled with the switch is dangerous and must be repaired.  
A tool that  
Always wear safety goggles or eye protection when using this tool. Use a  
dust mask or respirator for applications which generate dust.  
Disconnect battery pack from tool or place the switch in the locked or OFF” posi-  
tion before making any adjustments, changing accessories, or storing the tool.  
Such preventative safety measures reduce the risk of starting the tool accidentally.  
Do not grasp the tool or place your hands too close to the spinning chuck or  
drill bit.  
Your hand may be lacerated or may cause injury.  
Store idle tools out of reach of children and other untrained persons.  
are dangerous in the hands of untrained users.  
Tools  
Secure the material being worked on. Never hold it in your hand or across  
your legs.  
Unstable support can cause loss of control and injury.  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SYMBOLS  
IMPORTANT:  
Some of the following symbols may be used on your tool. Please  
Position yourself to avoid being caught between the tool or side handle and  
walls or posts.  
tion torque of the tool could crush your hand or leg.  
study them and learn their meaning. Proper interpretation of these symbols will  
allow you to operate the tool better and safer.  
Should the socket or bit become bound in the work, the reac-  
Check to see that keys and adjusting wrenches are removed from the  
SYMBOL  
NAME  
EXPLANATION  
Voltage (Potential)  
Current  
Frequency (Cycles per Second)  
Power  
Weight  
Type of Current  
Type of Current  
Cordless Drill before switching the tool “ON.  
at high velocity striking you or a bystander.  
Keys or wrenches can fly away  
V
A
Hz  
W
Kg  
Volts  
Amperes  
Hertz  
When using the Cordless Drill, always maintain a firm grip on the tool with  
both hands.  
Watt  
Hold tool by insulated gripping surfaces when performing an operation  
Kilograms  
Alternating Current  
Direct Current  
where the cutting tool may contact hidden wiring.  
Contact with a "live" wire  
will also make exposed metal parts of the tool "live" and shock the operator.  
Keep the handle of the Cordless Drill dry, clean, and free from oil and  
grease.  
Alternating or Direct Current Type of Current  
Earthing Terminal  
Class II Construction  
Minutes  
Seconds  
Diameter  
Grounding Terminal  
Denotes Double Insulation  
Time  
Time  
Size of Drill Bits,  
Grinding Wheels, etc.  
No-load Rotational Speed  
Revolutions, Surface Speed,  
Strokes, etc. per Minute  
Speed, Torque or Position Settings  
Do not run the Cordless Drill while carrying it at your side.  
A spinning  
socket or bit could become entangled with clothing and injury may result.  
min  
s
Disconnect the plug or remove the battery pack from tool and place the switch  
in the locked or OFF” position before making any assembly adjustments,  
changing accessories, performing any inspection, maintenance or cleaning  
procedures.  
Such preventive safety measures reduce the risk of starting the  
No load speed  
Revolutions per Minute  
tool accidentally.  
.../min  
Do not use the Cordless Drill if it has been damaged, left outdoors in the  
rain, snow, wet or damp eenvironments, or immersed in liquid.  
1,2,3, …  
Ring Selector Settings  
Maintain labels and nameplates on the Cordless Drill.  
These carry important  
information. If unreadable or missing, contact Alltrade for a replacement.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL DESCRIPTION  
BATTERY  
Before using battery pack, please read carefully all instruc-  
tions and cautionary markings on battery pack, battery  
charger and product using battery.  
3
5
6
7
8
®
Do not incinerate the battery pack even if it is severely dam-  
11  
9
aged or is completely worn out.  
The battery pack can explode.  
Do not carry battery packs in aprons, pockets, or tool  
boxes, product kit boxes, drawers, etc. with loose metal objects.  
12  
Battery  
4
10  
2
pack terminals could be short circuited causing damage to the battery pack,  
severe burns or fire.  
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic  
1
material by the Environmental Protection Agency.  
Before disposing of dam-  
aged or worn out Ni-Cad battery packs, check with your State Environmental  
Protection Agency to find out about special restrictions on the disposal of these  
battery packs, take them to your local recycling center for proper disposal, or  
CONTROLS AND COMPONENTS:  
1. Battery Pack  
2. Release Buttons on Each Side  
3. 120V AC Adapter  
4. Charger  
5. LED Charging Indicators  
6. 10mm (3/8") Keyless Chuck  
1-800-822-8837  
call  
.
8. Forward/Reversing and  
Trigger Lock Lever  
9. Variable Speed Controlled  
Trigger Switch  
10. Accessory/Bit Holder  
11. Comfort Rubber Grip  
The battery is not fully charged.  
Before first use, the battery pack requires  
8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5  
hours for the battery to be fully charged.  
7. 24 Adjustable Torque Settings  
Control Ring  
Always switch to a fresh battery when tool performance begins to diminish.  
Severe heat is most destructive to a battery; the more heat generated, the faster  
the battery loses power. A battery that gets too hot can have a shortened life.  
ACCESSORIES:  
12. Double Ended Screwdriver Bits (2)  
Never over-discharge a battery by using the tool even after tool performance  
has decreased.  
Do not attempt to discharge a tool’s battery by continuing to  
pull on the tool trigger. When tool performance begins to diminish, stop the tool  
and recharge the battery for optimal performance.  
COMPONENT  
BATTERY PACK  
120V AC ADAPTER  
CHARGER  
MODEL NUMBER  
691167  
691169  
691168  
Charge battery pack at ambient temperatures between 50° F – 104° F.  
Store tool and battery pack in locations where temperatures will not exceed  
10mm (3/8") KEYLESS CHUCK 690076  
120°F.  
This is important to prevent serious damage to the battery cells.  
The battery pack should always be recharged when the Cordless Drill begins to  
run slowly.  
When battery pack is not in use, keep it away from other metal objects such as  
paper clips, coins, keys, nails, screws or other small mettal objects that can  
make a connection from one terminal to another.  
together may cause sparks, burns, or fire.  
Shorting the battery terminals  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOVING/ATTACHING BATTERY PACK  
REMOVE BATTERY PACK:  
1. Press both release buttons on either side of  
the Cordless Drill to release the battery pack.  
CHARGING BATTERY PACK  
BATTERY PACK  
CHARGE BATTERY PACK:  
1. Make sure the trigger  
on the Cordless Drill  
OFF”  
is in the  
position  
120V AC  
ADAPTER  
2. Pull battery pack free of Cordless Drill.  
and remove the battery  
pack from the Cordless  
Drill.  
ATTACH BATTERY PACK:  
1. Align the raised portion of the battery pack  
with the groove in the battery compartment  
of the Cordless Drill.  
2. Plug 120V AC Adapter  
into household outlet  
LED LIGHT  
2. Press the battery pack into place. Make sure  
the latches are securely fastened. Do not use  
the Cordless Drill if the battery pack is not  
seated properly.  
and into side of battery  
charger. Insert battery  
pack into battery charger.  
When the battery is placed  
in the charger, the red  
BATTERY  
CHARGER  
RELEASE BUTTON  
LED indicator light will remain on.  
3. When fully charged, reattach battery pack onto Cordless Drill,  
making certain latches fasten securely. Cordless Drill will not  
operate properly if the battery pack is not seated properly.  
CHARGER  
Before using battery charger, please read carefully all  
instructions and cautionary markings on battery charger, battery pack and  
product using battery.  
ASSEMBLY  
Be aware that this tool is always in an operating condition  
because it does not have to be plugged into an electrical outlet.  
Always turn  
OFF”  
and remove the battery pack before changing bits.  
The charger will not automatically turn OFF” when the  
the switch  
battery pack is fully charged.  
ON”  
The charging indicator light will remain  
until the charger is disconnected from the electrical outlet.  
INSTALLING DRILL BIT INTO KEYLESS CHUCK  
Use only the charger which accompanied your product or direct replacement as  
listed in this manual.  
approved chargers with your product.  
Do not substitute any other charger. Use only Alltrade  
WARNING  
Before inserting a drill bit or other accessory,  
make sure the forward/reverse  
Do not disassemble charger.  
OFF”  
and trigger lock lever is in the center  
that may result in injury.  
position to prevent accidental starts  
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet  
or damp environments, or immersed in liquid.  
Do not attempt to tighten drill bits (or any other accessory) by gripping the  
The battery pack and charger heat during charging.  
Place the charger on a flat,  
front of the chuck and turning the tool on.  
and/or damage to the chuck.  
This may cause personal injury  
non-flammable surface away from flammable materials with at least four inches of  
clearance to allow proper air circulation around the charger and battery pack.  
When removing the bit from the tool, avoid contact with skin and use proper  
protective gloves when grasping the bit orr accessory.  
after prolonged use.  
When the battery pack requires recharging, a 3-5 hour charge allows the tool to  
Accessories may be hot  
operate at full power.  
A charging indicator light on the charger will illuminate to  
show that charging is taking place.  
11  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Hold the rear end of the chuck  
in one hand and use the other  
hand to rotate the front end in a  
counterclockwise direction to  
open the jaws of the chuck.  
FORWARD/REVERSE AND TRIGGER LOCK LEVER  
LOOSEN  
TIGHTEN  
Be sure the trigger is released when changing the position of the lever.  
LOCKED/OFF”  
Always store the tool in the  
position.  
2. Insert the shank of the bit (or  
other accessory) fully into the  
keyless chuck, taking care to  
keep the bit in the center of  
the jaws of the chuck.  
Always check the direction of the Cordless Drill's rotation before use.  
HOLD  
TO SELECT THE DIRECTIONS  
OF ROTATION:  
To select forward Cordless Drill  
3. Turn the front end of the chuck clockwise to hold the bit in place.  
rotation, press the trigger lock  
from left to right flat against the Cordless  
Drill body.  
4. Tighten securely by turning the front end of the chuck clockwise while holding  
the rear end.  
TRIGGER  
LOCK  
To select reverse, press the trigger lock lever  
in the opposite direction.  
OPERATING THE DRILL  
Never tape the trigger switch down to provide continu-  
The center position locks the tool.  
ous high speed.  
personal injury.  
The tool may fail under such conditions causing fire or  
TORQUE SETTINGS  
VARIABLE SPEED TRIGGER SWITCH  
To prevent damaging the tool or driving screw too deep  
into work piece, release the trigger when you feel the clutch slip.  
THIS TOOL IS CONTROLLED  
BY A TRIGGER SWITCH:  
The speed of the Cordless Drill depends  
on the amount of pressure you put on the  
trigger.  
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:  
For light duty work, use lower settings.  
CONTROL RING  
TRIGGER  
SWITCH  
For heavy duty work, use higher settings.  
The more pressure you apply, the faster  
the Cordless Drill will go.  
PROPER SETTING FOR DRIVING SCREWS:  
1. Set the ring on the lowest  
setting to begin.  
Release the pressure and the Cordless Drill  
will slow down.  
2. Try tightening the first screw.  
If the drill drives smoothly,  
proceed with the next screw.  
3. If the Drill’s clutch slips,  
increase the torque setting  
and try again until the Drill  
drives the screw without incident.  
13  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use a block of wood to back up work pieces that may splinter.  
Use spade bits when drilling large diameter holes in wood.  
Use HSS drill bits when drilling in metal.  
SCREWDRIVING  
WHEN DRIVING FASTENERS:  
Always start slowly and gradually increase the speed of the Drill.  
Release the trigger when you feel the clutch slip.  
Use masonry bits when drilling in soft masonry.  
Always keep the driver bit straight to prevent damage to the screw.  
Hold the Drill with both hands to ensure control if the bit should stick or slip.  
Use a lubricant when drilling metals other than cast iron, aluminum, copper,  
and brass.  
To prevent wood from splitting, drill pilot holes into the wood before driving  
in the screws.  
When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent  
slipping at higher speeds.  
DRILLING METAL  
ON”  
OFF”  
.
Never try to start a stalled Drill by clicking the trigger switch  
This may damage your tool.  
and  
WHEN DRILLING HARD METALS:  
Apply a lubricant, such as cutting oil, to the tip of the bit.  
To reduce jamming, always keep the Drill running when pulling the bit out of a  
finished hole.  
Start with a small hole then enlarge to the required size. Make sure the bit is  
actually cutting and not spinning in the hole as this will dull the edges of the bit.  
SCREWDRIVING:  
Always use the correct type and size of screwdriver bit.  
Keep enough pressure on the bit to keep it drilling through the material.  
DRILLING MASONRY  
• If screws are difficult to tighten, try applying a small amount of washing liquid or  
soap as a lubricant.  
WHEN DRILLING MASONRY:  
• Masonry can be brittle so be careful not to apply too much pressure and crack  
the material.  
Always hold the tool and screwdriver bit in a straight line with the screw.  
MAINTENANCE AND CLEANING  
Apply enough pressure to keep the bit cutting and not spinning in the hole as this  
will dull the edges of the bit.  
Always remove the battery pack before attempting  
cleaning or maintenance.  
Bricks and similar soft materials will require less pressure, concrete will require  
much more.  
DRILLING WOOD  
This Cordless Drill is lubricated before it leaves the  
factory.  
lubrication is required.  
This lubrication should last for the life of the tool. No further  
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits  
out of the hole frequently to clear chips from the flutes as an overburdened bit  
may overheat.  
Use only mild soap and a damp cloth to clean the tool.  
Never let any liquid get  
inside the casing. Never immerse any part of the tool in a liquid. Always keep the  
ventilation openings clear.  
HINTS FOR OPTIMUM USE  
Always clean the battery pack using only a dry cloth. Do not use liquids.  
Always unplug the charger before cleaning it.  
DRILLING:  
Keep the right amount of pressure in a straight line with the drill bit. Too little and  
the bit will spin without cutting, too much and the motor may stall.  
Regularly clean the ventilation slots in your tool and charger using only a soft  
bbrush or dry cloth.  
• Just before the drill tip breaks though the other side of the work piece drill more  
slowly and decrease pressure on the tool. This will prevent stalling and leave a  
cleaner hole.  
Never open the Cordless Drill case, battery pack or charger.  
Do not attempt to  
repair the Cordless Drill, battery pack or charger yourself. Opening any of these  
parts will void your warranty.  
15  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PROTECTING THE ENVIRONMENT  
ACCESSORIES  
BATTERIES  
Use only accessories that are recommended by the manufacturer for your model.  
Accessories that may be suitable for one tool may become hazardous when used on  
another tool.  
Alltrade batteries can be recharged many times. At the end of their useful life,  
recycle batteries with due care for our environment.  
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center  
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.  
1-800-822-8837  
. Collected batteries will be recycled or disposed of properly.  
or call  
If you must use an extension cord, be suree that the gauge is large enough to carry  
the amount of current necessary for your power tool.  
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge  
number, the heavier the cord (see table below).  
If not, your tool may experi-  
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS  
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would  
like further information on the following products, please contact Alltrade Customer  
Service Department at 1-800-590-3723.  
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS  
TOOL CURRENT RATING  
CONDUCTOR SIZE IN A.W.G  
Cordless Drills/Screwdrivers  
Impact Wrenches  
Sanders  
AMPERE  
3-6  
10FT.  
18  
25FT.  
18  
18  
18  
16  
50FT.  
18  
18  
18  
14  
100FT.  
18  
16  
14  
14  
-
6-8  
18  
Jigsaws  
8-10  
18  
10-12  
12-16  
16-20  
16  
14  
12  
Circular Saws  
12  
12  
12  
Angle Grinders  
12  
-
Reciprocating Saws  
Routers  
Rotary Tools  
SPECIFICATIONS  
Corded and Cordless Multi-Purpose Tools  
Wide Range of Accessories and more  
SPECIFICATIONS  
Voltage  
Speed  
14.4V  
0-550/min.  
24+ Drill  
Torque Settings  
Chuck Capacity (max)  
Charger Input  
10mm (3/8")  
120V  
60Hz  
Charging Time  
Battery Type  
Approx. 3-5 hours  
Ni-Cad  
17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
item and/or part will be repaired and/or replaced. If the unit is repaired, new or  
reconditioned replacement parts may be used. If Alltrade chooses to replace  
the product, it may replace it with a new or reconditioned one of the same or  
comparable design. The repaired or replaced unit will be warranted under the terms  
of the remainder of the warranty period. Typically, a defective product that is  
returned within the first 30 days after the purchase date will be replaced; for items  
returned after the first 30 days and within the warranty period, covered defective  
parts not subject to normal wear and tear or other exclusions will be repaired or  
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-  
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-  
conforming item and/or part thereof shall constitute fulfillment of all  
obligations to the purchaser. Alltrade shall not be responsible or liable for any  
expense, including freight charges, or repairs made outside Alltrade’s facility, unless  
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade  
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,  
commercial loss or consequential damages.  
2 YEAR LIMITED HOME USE WARRANTY  
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer  
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail  
purchaser of the accompanying KAWASAKI™ portable power tool and no one else  
all parts of the product (except those parts referred to below which are specifically  
excluded from such warranty (see Exclusions)) to be free from defects in materials  
and workmanship for a period of two years from original date of purchase.  
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:  
Kawasaki™ portable power tool is offered as a home use tool and carries a  
This  
HOME  
USE WARRANTY  
.
This tool is made for home use in the execution of  
COMMERCIAL  
projects and repairs in and around the home. Use of the tool for  
PURPOSES OR ON A JOBSITE  
is not covered under this warranty.  
The date of purchase shall be the date of shipment to the original purchaser, or the  
date the original purchaser took possession, custody or control of the product,  
whichever occurred first. This warranty shall be null and void if the product or any  
component thereof is modified, altered or used for any commercial purpose or on  
a jobsite. This warranty does not apply to any other product and/or component  
thereof manufactured or distributed by Alltrade, and does not apply to products  
and/or components thereof designed, manufactured and/or assembled by others,  
Exclusions  
This warranty does not cover parts damaged due to normal wear, abnormal  
conditions, misapplication, misuse, abuse, accidents, operation at other than  
recommended pressures or temperatures, improper storage or freight damage.  
Parts damaged or worn by operation in dusty environments are not warranted.  
Failure to follow recommended operating and maintenance procedures also  
voids warranty.  
THERE ARE NO WARRANTIES  
for which Alltrade makes no warranties whatsoever.  
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.  
Warranty Performance  
This limited warranty does not apply to accessory items such as drill bits,  
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding  
sheets and other related items.  
By purchasing the product, purchaser expressly acknowledges and agrees that their  
sole and exclusive remedy under this warranty shall be strictly limited to the repair  
or replacement of any covered nonconforming items or parts thereof provided that  
any such nonconforming item and/or part is promptly returned to Alltrade’s facility  
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,  
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)  
within the applicable warranty period, with a written request by purchaser that  
Alltrade repair and/or replace the nonconforming item and/or part. We recommend  
that you keep the original product packaging in the event you need to ship the unit.  
We suggest the package be insured against loss or in transit damage. When  
sending your product include your name, address, phone number, dated proof  
of purchase (or copy), and a statement about the nature of problem. Warranty  
coverage is conditioned upon purchaser furnishing Alltrade with adequate written  
proof that they are the original purchaser and of the original purchase date. Parts  
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will  
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if  
found to be defective and subject to warranty. Alltrade retains the sole discretion  
to determine whether any item or part is nonconforming and, if so, whether the  
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,  
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS  
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,  
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,  
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO  
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS  
WARRANTY.  
Alltrade will not be liable for the following: labor charges, loss or damage resulting  
from improper operation, maintenance or repairs made by other persons;  
pre-delivery services such as assembly, oil or lubricants, and adjustment;  
maintenance services that are normally required to maintain the product.  
The use of other than genuine Alltrade Repair Parts will void warranty.  
19  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty Disclaimers  
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH  
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,  
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL  
ALLTRADES AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF  
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF  
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY  
PERIODS SPECIFIED ABOVE.  
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,  
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY  
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR  
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING  
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE  
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF  
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,  
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY  
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE  
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE  
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY  
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR  
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASERS  
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.  
Limitations on Warranty Disclaimers  
Some states do not allow limitations on how long an implied warranty lasts  
and some states do not allow the exclusion or limitation of the incidental or  
consequential damages, so part or all of the above limitations or exclusions may not  
apply to you. This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
If your product is not covered by this warranty, please call our Customer Service  
Department toll free at 1-800-590-3723 for general repair information and charges.  
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE  
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE  
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR  
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE  
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,  
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT  
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,  
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY  
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF  
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING  
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE  
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY  
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.  
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH  
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING  
THEREFROM OR BASED THEREON. PURCHASERS SOLE AND EXCLUSIVE  
REMEDY IS AS STATED ABOVE.  
Limitation Of Liability  
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR  
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY  
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH  
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS  
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,  
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR  
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS  
21  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Washer Dryer WIDXE 146 S User Manual
Infinity Portable Speaker SAT 450 OM User Manual
Jenn Air Refrigerator JS48CSDWDA User Manual
JL Audio Speaker Subwoofe User Manual
JVC CRT Television AV 36P903 User Manual
JVC Radio KD R310 User Manual
JVC Security Camera TK S241U User Manual
JVC Speaker System UX P7 User Manual
Kathrein Satellite TV System UFS 740sw User Manual
King Canada Drill PDM 30 User Manual