MODEL
#840067
PORTABLE JIGSAW
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
YOUR FEEDBACK IS VITAL TO US.
Download from Www.Somanuals.com. All Manuals Search And Download.
WORK AREA
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade is wider
than the other.) This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation eliminates the need for the three wire grounded power cord
and grounded power supply system.
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
Some examples of these chemicals are:
• Lead from lead-based paints.
Don’t expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug from
an outlet. Keep the cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords increase the risk of electric
shock.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
When operating the tool outside, use an outdoor extension cord marked “W-A”
or “W.”These cords are rated for outdoor use and reduce the risk of electric shock.
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in
serious personal injury.
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools
with your finger on the switch or plugging in tools that have the switch on invites accidents.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a “live” wire will also make
exposed metal parts of the tool “live” and shock the operator.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
IMPORTANT SAFETY RULES FOR JIGSAWS
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat or hearing protection must be used for appropriate conditions.
Always wear safety goggles or other approved eye protection when using this
tool. Always use an appropriate dust mask or respirator during operations
where dust can be generated. To reduce exposure to these chemicals always
work in a well ventilated area. Use approved safety equipment and dust masks
that are specially manufactured to filter out microscopic particles.
TOOL USE AND CARE
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Hold the Jigsaw by the insulated gripping surfaces when performing an opera-
tion where the blade may contact hidden wiring or the tool power cord. Contact
with a "live" electrical wire will make exposed metal parts of the jigsaw "hot" and cre-
ate a potential for electrical shock to the operator. Do not cut into existing walls or
other blind areas where existing electrical wires may be present. If this situation is
necessary, remove all fuses and/or turn all circuit breakers off in the work area. After
cuts have been completed in the blind areas, inspect to ensure that no electrical wire
was cut or nicked before reinstalling fuses and/or engaging circuit breakers.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
Never leave the jigsaw with the trigger left in the locked "ON" position. Before
plugging in the jigsaw, inspect to make sure the trigger lock is in the "OFF" posi-
tion. Accidentally plugging the jigsaw in with the trigger lock engaged can result in
premature starting of the tool, which can cause damage to the tool and/or serious
injury to the operator.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Keep hands away from the cutting area. Do not reach under material being cut
while the jigsaw is running. Serious injury could occur. Always turn the jigsaw
"OFF" before inspecting the cutting area.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used
on another tool.
Do not use dull or damaged blades with the jigsaw. Bent or damaged blades can
break or cause a kickback resulting in serious injury to the operator. Dull blades will
cause the jigsaw to perform improperly and may damage the tool.
SERVICE
Before starting to cut with the jigsaw, turn it "ON" and allow the blade to come to
full speed. The jigsaw can chatter or vibrate if the blade speed is too slow at the start of
the cut. This can cause the jigsaw to kickback and damage the work area or cause injury.
Tool service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel may result in a risk of injury.
Always secure working material before attempting to make a cut with the jigsaw.
Never hold the material with your free hand or across your legs. Small or thin mate-
rial may flex or vibrate causing loss of control and possible injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions could create a risk of shock or injury.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure all adjusting screws on the jigsaw are firmly tightened. Failure to
tighten the adjustment screws can cause the blade to disengage from its holder
possibly damaging the jigsaw or causing injury to the operator.
FUNCTIONAL DESCRIPTION
Disconnect the power plug from the AC power source
before any assembly, adjustments, or adding/removing accessories.
Following this preventative step reduces the risk of the saw coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
When removing the blade or other accessories from the jigsaw, avoid contact
with the skin. Always wear protective gloves when handling the jigsaw or any
accessory. The blade can become hot after prolonged use and will cause burns.
SYMBOLS
Speed Control
Switch
Trigger Lock
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
Power Cord
Strain Relief
Power
Cord
Gear
Housing
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
V
A
Hz
W
Kg
Trigger
Vacuum
Attachment
Blade Guard
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
Hex Wrench
Storage
min
s
Baseplate
Blade
Holder
Bevel Plate
Bevel Markings
Roller Guide
Blade
No load speed
Revolutions per Minute
.../min
FIGURE 1.
JIGSAW COMPONENTS
1,2,3, …
Ring Selector Settings
Note: For tool specifications, refer to the nameplate on the jigsaw.
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
JIGSAW OPERATION
ASSEMBLY
ADJUSTING SPEED
Disconnect plug from AC power source before
assembling parts, making adjustments, or changing blades. Failure to
remove electrical power could cause accidental starting of the jigsaw resulting
in serious injury to the operator and/or damage to the tool.
The operating speed of the jigsaw can
be varied by using the Speed Control
Switch located on the top of the
jigsaw. Turn the speed control from
0 to 6 to set the speed. On most cuts,
such as wood and metal, the faster
speed works best. On other materials,
such as plastic or laminants, a slower
speed might be necessary to reduce
vibration and make smoother cuts.
Speed Control
Switch
6
0
ATTACHING THE BLADE
Trigger
1. Firmly grip the plastic blade guard
Trigger Lock
Blade Guard
Hex Wrench
and slide it up to expose the blade
clamp.
FIGURE 4.
ADJUSTING THE SPEED CONTROL SWITCH
2. Using a hex wrench (provided in a
slot beneath the motor), loosen the
two hex socket-head screws on the
blade clamp until it slides forward
enough to open a slot for the blade.
TRIGGER "ON-OFF" SWITCH
Plug the jigsaw into an approved 115 V AC outlet. This tool is double insulated
and equipped with a polarized plug (one blade is wider than the other). Double
insulation eliminates the need for a special three-wire grounded power supply.
Holding the jigsaw by the insulated handle, squeeze the trigger to turn the jigsaw
ON and release the trigger to turn the jigsaw OFF. Allow the blade to reach the
maximum set speed before bringing it in contact with the workpiece.
Loosen
Tighten
3. Insert the blade into the blade
clamp with the cutting edge
facing to the front of the jigsaw.
Hex Socket-head
Screws
Roller Guide
CUTTING TIPS
Blade
Blade Guard
Place the finish side of the
workpiece down and clamp it
to a workbench or table. Draw
FIGURE 2.
MOVING THE CLEAR PLASTIC BLADE
GUARD TO LOOSEN THE BLADE CLAMP
Jigsaw
cutting lines on the back side.
Place the front edge of the saw
baseplate on the workpiece
and line up the blade with the
line to be cut. Press the jigsaw
down firmly on the workpiece
and cut slowly along the
guidelines. Build up cutting
speed as you progress. If you
want to leave room for finish
sanding, cut slightly to the out-
side of the drawn guidelines.
Workpiece
(Finish Side
Facing DOWN)
4. Using a hex wrench, securely tighten
the two hex socket-head screws on
the blade clamp.
GripBladeGuardat
bottom-rearand
pressinwardto
slideupward.
5. Using a hex wrench, loosen the two
hex socket-head screws holding the
bottom board and the guide roller
on the saw housing.
Guideline
Blade
6. Slide the guide roller forward until the
back of the blade fits loosely in the
center groove. Using a hex wrench,
securely tighten the two hex socket-
head screws holding the guide roller
and bottom board to the saw housing.
Baseplate
FIGURE 3.
FIGURE 5.
MAKING THE INITIAL CUT
INSERTING THE BLADE
INTO THE BLADE CLAMP
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUNGE CUTTING
Plunge cutting is useful when it is
Do not force the jigsaw into the workpiece. This could
cause the blade teeth to wear down with-out cutting or even cause the blade to
break causing damage to the jigsaw or injury to the operator. Let the saw reach
full speed before engaging the workpiece.
Guidelines
Starter Holes
necessary to make cutouts inside the
workpiece. First, draw lines where the
cut is to be made. Drill guide holes in
the four corners. Turn on the jigsaw
and insert the blade into one of the
starter holes. Move the jigsaw along
the cutlines until rough cut is finished.
If the cutout needs square corners, use
the jigsaw to finish cutting the corners
after the cutout is done.
CUTTING WITH A STRAIGHTEDGE
Whenever possible, use a coarse
cutting blade. Fine-tooth blades pre-
vent the cuts from being made
smoothly and risk the possibility of
the blade wearing out prematurely or
Baseplate
Against
Straightedge
even breaking.
Clamp a rigid straightedge onto the
workpiece leaving enough room for
the jigsaw baseplate to slide along
Line of
Cut
FIGURE 6.
PLUNGE CUTTING
beside it while lining up the center of
the blade with the drawn cut lines.
This can best be done by taking a
measurement from the blade to the
outside edge of the baseplate and
making several marks the same
distance along the cutline so the
straightedge can be clamped parallel
to the cutline.
METAL CUTTING
Metal cutting requires a different type blade than the ones used on other materials.
Do not try and cut metal workpieces with a regular jigsaw blade. Refer to the
Assembly Instructions for changing the blade. When cutting metal, clamp the
material down securely. Grasp the jigsaw firmly and push the blade slowly into the
metal. Use slower speeds and lubricate the blade with cutting wax, if available, or
kerosene or cutting oil. When cutting thin metal, sandwich it between pieces of thin
wood.
Clamp
FIGURE 5.
CUTTING WITH A STRAIGHTEDGE
When cutting aluminum conduit or angle iron, securely clamp it in a vise and cut as
close to the vise jaws as possible. When cutting tubing with a larger diameter than
the blade depth, cut through the wall of the tube, insert the blade into the cut and
rotate it toward the front edge of the saw.
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BEVEL OR ANGLE CUTTING
The jigsaw baseplate can be tilted
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
from 0º to 45º for making bevel or
angled cuts.
Blade
1. Make sure the trigger is fully released
and not in the locked-on position.
Unplug the power cord from the AC
power source.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
Roller Guide
2. Turn the jigsaw over so the baseplate
faces up. Using the 3 mm hexwrench,
loosen the two hex socket -head
screws attaching the baseplate.
Loosen both
hex socket-
head screws
to tilt the
baseplate for
bevel cuts
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
3. Rotate the baseplate to the desired
angle. There markings for 0º and 45º.
If another angle is desired, line up the
baseplate to a protractor using the
jigsaw blade as reference.
18
16
14
14
-
4. When the proper angle is obtained,
securely tighten the two hex socket-
head screws with the hexwrench.
Make sure the roller guide is placed
back against the blade.
14
12
12
12
12
12
Bottom View
-
FIGURE 7.
BEVEL CUTTING
SPECIFICATIONS
SPECIFICATIONS
Voltage
Rated Current
Strokes per minute
Max. Cutting Thickness Wood 55mm
Steel 6mm
MAINTENANCE AND CLEANING
120V
3.5A
500-3000/min
60 Hz
CLEANING: To avoid accidents, be sure to disconnect the
tool from the electrical power source before any cleaning or maintenance.
The tool can be cleaned by using compressed dry air. If compressed air is not
available, a soft natural bristle paint brush will work. Always wear safety gog-
gles when cleaning tools with compressed air.
Avoid using certain cleaning agents and solvents.
Chemicals like gasoline, carbon tetrachloride, acetone, paint thinner or ammo-
nia products can damage the plastic parts of the tool.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Performance
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #310-522-9008)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of
projects and repairs in and around the home. Use of the tool for COMMERCIAL
PURPOSES OR ON A JOBSITE is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-310-522-9008 or toll free at 1-800-590-3723 for general repair
information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2005 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
1-800-590-3723
Printed in China
840067 – Portable Jigsaw
Download from Www.Somanuals.com. All Manuals Search And Download.
|