Operating manual
Kathrein Satellite Receiver
UFD 345
Order No.: 260 411
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls, displays and connections
Bedienelemente, Anzeigen und Anschlüsse
This section contains a brief description of all the control elements, displays and
connections. The key symbols presented here are also used when describing the
operating sequences.
View of front panel
View of rear panel
Remote control handset
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls, displays and connections
Front panel
Rear panel connections
1
Satellite IF signal input and
output of LNB supply voltage
1
Location slot for infrared sensor
2
Detachable infrared sensor
2
3
4
5
6
Connecting socket for infrared sensor (Western 8-way)
Scart socket, TV connection
Receiver for infrared signals from the remote control.
The detachable infrared sensor allows the receiver to be in-
stalled hidden from view. All that is necessary is for the in-
frared sensor to be within the reception area of the infrared
signals from the remote control.
Scart socket, VCR connection
Scart socket, decoder connection
3
4
On/Off indicator (red LED)
In standby the indicator goes out
Connecting socket for voltage supply
12 ... 24 V DC
Programme selection keys
Step-by-step programme selection (upwards and down-
wards).
Switch-on from standby by pressing both buttons simulta-
neously.
Switchover from TV- to radio mode by pressing both but-
tons simultaneously. .
Remote control handset keys
Function 1:
On/Off (Standby),
Key to call up picture optimisation menu if reception is
poor
Attention: no mains isolation results!
Function 2:
Resetting from setup menu into normal operation
Numeric keys 0 - 9 for programme selection and
frequency entries
Function 1:
Command set changeover
Function 2:
Blanking of video signal (in setup mode)
to
Function 1:
Function 1:
Volume control
Switchover to radio mode
Function 2:
Function 2:
Selection of individual menu entries in setup mode
Calls up menu for radio settings
(with
in succession)
Function 1:
Function 1:
Calls up the Info menu
Steps through programmes either up or down
Function 2:
Function 2:
Calls up menu for “Programme slot swapping, in-
sertion and copying”
Changing data in setup mode
(with
in succession)
Function 1:
Function 1:
Mutes the sound
Saves the chosen settings
Function 2:
Function 2:
Calls up menu for audio settings
Primary key for calling the separate setup menus
(e.g. video settings)
(with
in succession)
Unassigned
Stereo/Mono- (2 channel) changeover
Function 1:
Selects TV/SAT mode
Function 2:
Calls up menu for video settings
(with
in succession)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions
Sicherheitshinweise
The following section contains important information relating to operation, place of
installation and connecting-up of the receiver. Read these notes carefully before
putting the unit into operation.
Important notes regarding operation
Extended absence/Thunderstorms
During periods of extended absence or at the onset of thunderstorms always dis-
connect the unit from the supply, or withdraw the mains plug if the power supply
unit is used. This also applies to any other equipment attached.
Mains lead
Make certain that the mains lead (power supply lead) is undamaged. Never put the
unit into operation if the mains lead is damaged.
Cleaning
Withdraw the PSU mains plug before cleaning the unit. Use a dry cloth for clean-
ing.
Children-at-play
Pay attention that children do not insert objects into the ventilation slots. There is a
risk of mortal danger due to electric shock.
Repairs
On no account remove the housing cover since there are dangerous voltages in-
side the unit that may be contacted. The unit must only be opened by qualified
specialists, so allow them to carry out any repairs or adjustments to your receiver.
Unauthorised opening entails loss of guarantee.
The electrical safety of the unit can be affected by improper tampering with it
The manufacturer‘s liability excludes accidents occurring to the user when the unit
is opened.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions
Important notes for siting and installation
Place of installation
Every electronic device generates some heat. The rise in temperature, however,
lies within safe limits. Nevertheless, this does not rule out the possibility of slight
colour changes to sensitive furniture surfaces and veneers over time due to the
constant effect of heat.
In conjunction with treated furniture surfaces, the unit‘s rubber feet can likewise
give rise to changes in colour. Where necessary, place the unit on a suitable pad.
Ventilation
The heat that is generated in this unit is dissipated quite adequately. Never install
the receiver in a cabinet, shelf or rack with inadequate ventilation. Never close-off
the openings on the unit that are intended for heat dissipation.
Do not place objects on top of the unit. Maintain a clearance of at least 10 cm
above the unit so that the heat generated within the unit is convected away without
obstruction.
Mains voltage
Run the receiver only from a 12 –24V d.c. voltage supply or from 230 V / 50 Hz
when using the mains pack supplied.
The unit is not to be connected to the mains until after all the installation work has
been completed.
Humidity
Protect the unit against humidity, drips and splashes.
Solar radiation/heat
LNB supply voltage
Do not place the receiver close to radiators nor expose it to direct sunlight.
If the feeder system (LNB) is supplied with an external supply voltage and the LNB
supply voltage is not used for polarity switchover (e.g. Kathrein single-cable feeder
system UAS 330), the receiver‘s LNB supply must be set to “OFF”(refer to section:
“Initial settings, LNB supply voltage“).
There is a risk that the receiver may suffer damage if the change-over is not carried
out.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting up and putting into operation
Anschluß und Inbetriebnahme
A sample configuration is to be found in section: “Connection example“.
Attention!
Do not connect the unit to the mains supply until after the installation work has
been carried out properly..
Please take note of guidance in section: “Safety- and Installation Instructions”
Installing the receiver
The UFD 345 satellite receiver is suitable for mobile use in motor homes or cara-
vans, but can also serve as a fixed station in the home.
Place of installation
The modern, elegant design of the receiver with its modest dimensions means it
can be placed in visual range, on top of the TV set, for example. In this case, insert
the infrared sensor into the locating slot on the front of the receiver and run the ca-
ble to the rear via the cable channel on the bottom of the receiver (see below).
Connect the Western plug to the Western socket (2).
Due to its modest dimensions, however, the receiver can also be placed concealed
from view behind the TV set. Alternatively, the receiver can be mounted on the
wall. For this, there is a drilling template for the required drill holes at the end of the
guide. Cut the template out if required. In this case, the infrared sensor is sited
separately.
Infrared sensor
The detachable infrared sensor receives the signals from the remote control and
passes them on to the receiver via the cable. As a result, it allows the sensor and
receiver to be sited separately. Consequently, the receiver can be sited outside the
reception range (line of sight) of the remote control, thus saving on space.
Connection of the sensor to the receiver is via the 8-way Western plug, which you
should connect to the Western socket (2) on the rear of the receiver.
For optimum working, the infrared sensor should be sited at a clearly visible spot
near the TV set
Connecting up the unit
Power supply
With mobile use, the receiver should be connected directly to the vehicle‘s on-
board supply (12 ... 24 V) using the adaptor cable included (adaptor cable with uni-
versal plug for cigarette lighter or vehicle socket outlet and inner hollow conductor
plug).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting up and putting into operation
Connect inner hollow conductor plug to the power supply socket (6).
Caution!
If the power supply cable is modified or a different one is used, it is essential to
check for correct polarity. Incorrect polarity will result in damage to the receiver.
For fixed applications use the accompanying
power supply unit 230 V~/16 V=.
Satellite signal connection
•
Connect the Sat IF input of the receiver to the satellite receiving system.
•
For the connection use a coaxial cable with an F-type connecting plug.
If the F connector is not yet fitted to the cable:
•
•
Insulate the cable as indicated in the following illustration, and
Carefully screw the F connector onto the cable end until it is firmly seated on
the cable.
Attention!
Do not use any tools to screw the F plug onto the cable or to tighten to the F
socket. Put the connectors on hand-tight only.
Attention!
When fitting the plug, make certain that none of the fine wires of the braided shield
makes contact with the inner conductor giving rise to a short-circuit.
Receiving system presets
Presetting carried out for the control signals was for conventional receiving sys-
tems, thus 14/18 V for polarity switching and 22 kHz switching signal for satellite
selection in the case of multifeed receiving systems.
If DiSEqC or tone-burst switching matrices are to be used in the receiving system,
the setting must be selected for "DiSEqC" signal or "Tone Burst” in the initial setup
menu at submenu “DiSEqC“.
For this, refer to section: “Initial settings, DiSEqC menu“.
Also take note of the technical guide for the matrices.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting up and putting into operation
TV and video recorder connection (VCR)
•
Connect-up the satellite receiver (TV Scart socket) and TV set with a Scart ca-
ble.
If your TV set has stereo capability, a Scart connection allows you to receive the
sound in stereo.
•
Connect-up the video recorder and satellite receiver (VCR Scart socket) again
using a Scart cable.
Decoder connection
You can also connect-up a decoder to the receiver for Pay-TV programmes.
No further setting is necessary for decoders that require a video signal and supply
a switching signal, such as Premiere decoder and Videocrypt decoder, for exam-
ple..
Important
With decoders that do not supply a switching voltage, the receiver must be pro-
grammed appropriately beforehand (see “The video menu” section in chapter “Pro-
gramming TV programmes“).
Also take note of the decoder specification!
•
Using a Scart cable connect-up the decoder to the decoder Scart socket.
Inserting batteries into remote control handset
•
Remove the cover on the rear of the remote control handset.
•
Insert both of the batteries supplied into the remote control handset.
Make certain that the batteries are inserted with the correct polarity!
•
Replace the cover again.
Note
Exhausted batteries are special waste and should not be disposed of with house-
hold refuse. Instead, hand them in to a collection centre for used batteries!
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver operation
Bedienung des Receivers
In this chapter you learn how to select TV and radio programmes using your re-
ceiver, and how to adjust the volume and set up other functions.
Switching the unit on
•
Once the supply voltage is connected the unit goes into standby mode.
key on the remote control is used to switch between standby and
normal operation. Operation is shown by means of a red LED indicator in the
infrared sensor.
•
The
The last programme slot selected is tuned in (last-status memory).
•
Switching between TV and radio mode
Your receiver allows you to receive TV programmes or radio programmes.
After switching on, the receiver is in either the TV mode or the radio mode (de-
pending on the mode when switched off).).
In TV mode, the programme slot indicator in the on-screen display (OSD) begins
with "P". In radio mode, the screen is blanked out and the on-screen display begins
with "R “.
..
Press the
radio mode.
key on the remote control handset to switch between TV- and
•
In the initial setup menu, a continuous on-screen display of the radio programme
slot can be selected independent of the TV setting (see section: “Initial settings, On
Screen Displays “).
Note
Selecting a programme
Use the numeric keys
...
to select the desired programme directly.
•
Example for a three-digit entry (with setting “free programme selection”):
Selection of programme slot 147
1 is entered, programme slot 1 appears
4 is entered, programme slot 14 appears
7 is entered, programme slot 147 now appears.
•
•
•
or
Use the
keys to step through the programmes in succession.
•
After the programme changeover, the programme slot and programme name are
superimposed on the screen for approximately three seconds.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver operation
Note
With the setting “2- or 3-digit programme selection” there is a switch to the desired
programme after approximately 3 seconds. Digits can be entered during this time
period.
With the setting “free programme selection“, the receiver switches to the corre-
sponding programme slot immediately after each input. (see example above).
In the initial setup menu, a continuous on-screen display of the programme slot can
be selected (see section: “Initial settings, On Screen Displays “).
Adjusting volume, balance and tone
•
If you press one of the
of the volume, balance, tone (treble and bass), stereo-width and pseudo-stereo:
keys the following menu appears for adjustment
With the
keys or the
key you can select the respective menu entry
keys.
and then makes changes with the
The settings are not operative at the VCR Scart socket in order not to disturb video
recordings.
The on-screen display is removed again after approximately 3 seconds.
In the menu entry “Stereo Width" the stereo base width can be adjusted independ-
ently.
Note
“Pseudo-Stereo" can be used to simulate a “stereo-like” effect with mono pro-
grammes, and should thus only be activated with mono reception.
The “pseudo-stereo” effect can be simulated if a stereo programme is switched to
mono.
Muting the sound
Press the
key.
The sound is muted, allowing you to make a phone call undisturbed, for example.
Press the key again to turn the sound back on.
•
•
Mute is not operative at the VCR Scart socket.
Note
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver operation
Stereo- / Mono- / Channel changeover
Broadcasts can be transmitted in the two-tone channel method
(e.g. original tone “English" on channel 1, “German" tone on channel 2).
•
Press the
nel in the order:
key. Each time you press the key, you switch the sound chan-
Stereo → Channel 1 → Channel 2 → Stereo
•
The selected channel is shown on the screen.
The setting is not saved. After a change in programme the programmed setting
takes effect again.
Video recorder playback (VCR)
For playback from the video recorder, the satellite receiver needs to switched on to
ensure the signal path is switched through from the VCR Scart socket to the TV
Scart socket.
SAT/TV changeover
Where the satellite receiver and TV set are connected via a Scart cable, many TV
sets immediately switchover signal input to video reception (on the Scart socket)
when the satellite receiver is turned on. The switching voltage of the TV Scart
socket therefore needs to be switched off if you want to view a terrestrially broad-
cast TV programme.
•
Press the
key.
The switching voltage on pin 8 of the TV Scart socket is turned off, and it is turned
on again by pressing once more.
In Sat mode, “Sat mode” is displayed on the screen for approximately 3 seconds.
Operating the receiver without remote control
On connecting the satellite receiver to the supply, the unit always reverts to the last
operating mode it was in prior to being switched off.
If the unit was disconnected from the supply whilst in standby mode, it reverts to
standby mode on reconnection to the supply. If you happen to have mislaid the re-
mote control handset, you can switch the receiver on by simultaneously pressing
both
keys on the infrared sensor.
You can switch between the “TV” and “Radio” operating modes in the same
manner.
Swapping, sorting and copying programmes
With the function: “Swapping, sorting (inserting) and copying programmes” you can
adapt the programme order to suit your individual requirements..
•
If you want to alter the current programme order, you can do this with the func-
tions:
− Swap programme slots or
− Insert programme slot (sort) or
− Copy programme slot.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver operation
Example
You want to insert the programme from programme slot “P083" into programme
slot “P003"
•
•
Select programme slot P083 using the
...
keys or the
keys.
Press the keys in succession.
+
The menu for the function "Swap programme slots" appears.
Press the key once again.
•
The screen display for the “Insert“ function now appears:
▲▼
Select programme slot P003 using the
keys or the
keys.
•
•
…
Press the
key twice.
The programme from programme slot 83 is now inserted at programme slot 3.
The following message appears on the screen:
Please wait
Following message appears when exchange completed:
Programme inserted!
To switch to the "Copy" mode press the
key once again.
•
•
Exit from the menu with
.
Displaying the Info menu and programme overview
Displaying Info
The unit is in normal mode of operation (TV- or radio mode)
Press the
key.
•
The Info menu appears with instructions for calling the setup menus for initial-,
video- and audio settings and the programme list in TV mode, plus instructions for
calling the setup menus for initial settings and radio settings in radio mode.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver operation
Programme overview
(in TV mode only)
•
Press the
key once again:
The programme overview appears on the screen.
The programme currently selected is indicated by <..>.
•
The
keys can be used to single-step through the programme list
keys allow you to page through in steps of 10.
while the
•
Pressing the
key once results in switchover to the marked programme.
On exiting the programme overview with
the previous programme.
key there is a switch back to
•
•
Pressing the
and exit from the programme overview.
key twice results in switchover to the marked programme
To exit from the menu without selecting a programme press key
.
Picture optimisation when reception is weak
Where weak reception results in a grainy picture as, for example, at the fringes of
the reception area, the "Picture optimisation" function can be used to achieve an
improvement.
•
Press the
key. The following on-screen display appears:
With the
keys you can now carry out picture optimisation.
Note
The power radiated by individual transponders (satellite programmes) varies. Be-
sides this, the footprints of the transponders are also different. Picture optimisation
must therefore be carried out for each programme and is not stored either. This
means that picture optimisation must be carried out again after changing the pro-
gramme.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming TV programmes
Programmieren von TV-Programmen
The satellite receiver has already been factory pre-programmed for satellite re-
ceiving systems with feed systems (receiving system) which have an oscillator fre-
quency of 9.75 GHz. All of the programmes set up are listed in the table enclosed.
If your satellite receiving system uses a feed system with a different oscillator fre-
quency, the receiver only needs to be matched to the feed system oscillator fre-
quency during the installation.
The procedure for this can be found in section: “Initial settings, Oscillator fre-
quency“.
Tuning in TV programmes
To tune in to new TV programmes, the video and audio reception parameters need
to be set up accordingly.
The latest programme assignments can be obtained from satellite programme
magazines, or called up via the videotext of programme Sat 1 from page 516.
•
First select the programme slot that you want to programme afresh.
•
Call up the video menu by pressing the
+
keys in succession.
or
•
•
Call up the audio menu: press keys
+
in succession.
Switch between video and audio menus using
the key or the key.
•
Select the desired menu line using the keys
.
•
For direct numeric input use the keys
…
.
or
•
•
•
Alter the values step-by-step using the
keys.
Press the
key twice in order to save your settings.
key.
Exit from the menu with the
Note
You can terminate any setup procedure immediately (also without saving settings)
by returning to normal operation with the key.
The “Video” menu
The following settings can be made in the video menu:
Prog ra m m e slot:
Prog ra m m e na m e :
P002
ZDF
Sa t-Fre q ue nc y:
Pola risa tion:
Orb it Position:
De via tion:
10964 MHz
Hor. Lo w
1
16 MHz
LO 1
Osc illa tor:
De c od e r m e nu...
STOR
VOL 0-9 VID AUD A/ B STBY
The bottom line shows the keys you can use to make the settings.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming TV programmes
Satellite frequency
With input via the numeric keys
...
frequency input is in 5-figure form in
keys you can attain the optimum
the range 10700 to 12747 MHz. With the
receiving frequency by moving in 1 MHz steps (recommended if the picture is
grainy due to weak signals).
Polarisation/Orbit position
In these two menu entries, signal selection is carried out by the LNB supply voltage
and the 22 kHz switching signal, which is superimposed on the LNB supply volt-
age.
Polarisation
In the “Polarisation“ menu entry, the voltage level is used (14 or 18V) to set the
polarity (vertical or horizontal) and the 22 kHz switching signal to select the fre-
quency range (see table).
Frequency range Polarisation LNB voltage
Switching
signal, 22 kHz
Off
Setting
10.7-11.7 GHz
vertical
14 V
18 V
Vert. Low
Hor. Low
horizontal
Off
Orbit position
In the “Orbit Position” menu entry, the 22 kHz switching signal is used to switch
between two (or more) satellites for multifeed receiving systems (see following ta-
ble).
Satellite
Orbit position
22 kHz switching
signal
Astra 19.2° east
Eutelsat 13° east
Eutelsat 10° east
Eutelsat 16° east
1
2
3
4
Off
On
Off
On
In the initial setup menu (submenu ”DiSEqC”), setting is carried out for the menu
entry the 22 kHz switching signal is operative for (polarisation or orbit position).
Note
With Astra satellites, only digital signals are transmitted in the upper frequency
band (high-band). Special receivers are also required, however (DVB receiver;
d-Box).
The customary (analogue) signals are transmitted on the lower frequency band
(low-band). The same is also true at the moment for Eutelsat programmes.
•
Select the required polarity therefore as either Vert. Low or Hor. Low only.
In the factory presetting (as delivered), the setting “Pos. A/B” has been chosen in
the “DiSEqC” initial setup menu, menu entry “22 kHz signal”.
The settings Vert. High and Hor. High are not operative.
Video deviation
Oscillator
The satellites transmit their signals with different video deviation, 16 or
25 MHz. The setting has an effect on the picture brightness.
•
Adjust the video deviation to obtain optimum picture brightness.
The receiver is equipped with four LO frequency groups (LO 1 to LO 4), which can
be set to give troublefree matching to different feed systems with different oscillator
frequencies (e.g. Telecom 1A).
In the delivered state, all four oscillator frequencies are set to 9.75 GHz
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming TV programmes
(9750 MHz).
The LO frequency groups are also used for satellite recognition during fully auto-
matic adjustment with our HDP 150 automatic positioner.
For this the individual satellites are assigned the following LO groups:
Satellite
LO group
Astra
LO 1
LO 2
LO 3
LO 4
Eutelsat 13°
Eutelsat 10°
Eutelsat 16°
To change the LO frequencies refer to the initial setup menu.
Decoder menu
You can attach a decoder to the decoder Scart socket for a Pay-TV programme.
The receiver recognises Pay-TV programmes for which decoders supply a switch-
ing signal (e.g. like Premiere) independently, and switches this signal through to
the TV- and VCR Scart socket.
For decoders that do not supply a switching voltage the following setting is to be
carried out.
•
•
•
•
•
Call up the video setup menu,
Select menu entry “Decoder menu“,
Activate the “Decoder menu“.,
Set the video signal path to external,
Set the audio signal path to external only if audio signal is encoded as well.
Note
If the decoder connected requires a baseband signal with PAL- or MAC-de-
emphasis, a setting of baseband PAL or baseband MAC needs to be made in
menu entry "Signal type" (take note of decoder specification).
•
Save the settings with the
key (press twice).
Programme name
In the “Programme name“ line, you can enter a 5-character station identifier of your
choice.
•
•
•
•
•
Using the
Using the
with the
key select the menu entry: “Programme name“.
keys select the first character.
key move on to the next character..
Select the remaining characters in the same way.
Change to the “Audio menu” with the key.
or
•
Press the
key to return to reception mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming TV programmes
The “Audio” menu
The following settings can be made in the audio menu:
P002
ZDF
TV sound
Mod e :
Fre q ue nc y:
De -e m p ha sis:
Ste re o
7.02/ 7.20 MHz
DNR/ 75µs
VOL 0-9 VID A/ B STOR STBY
Audio mode
Setting of operating mode as: “Stereo”, “Mono narrow” or “Mono wide”
Operating mode “Stereo“ and “Mono narrow“ is selected on reception of the sound
sub-carrier, “Mono wide“ is selected on reception of the sound main carrier.
Audio frequency
Input of the audio frequency via the numeric keys
...
is in 3-digit form in
the range 5.00 to 8.80 MHz. In stereo mode, the frequency is to be entered for the
left sound channel. The frequency for the right sound channel then automatically
lies 180 kHz above the left sound frequency.
The following is a list of fixed, pre-programmed audio frequencies that can be se-
lected using the
keys.
Mode
Sound carrier fre-
quencies
Mode
Sound carrier fre-
quencies
Stereo
7.02 / 7.20 MHz
7.38 / 7.56 MHz
7.74 / 7.92 MHz
8.10 / 8.28 MHz
Mono
(narrow)
MNR
7.02 MHz
7.20 MHz
7.38 MHz
7.56 MHz
7.74 MHz
7.92 MHz
8.10 MHz
8.28 MHz
5.80 MHz
6.50 MHz
6.60 MHz
6.65 MHz
6.80 MHz
Mono
(wide)
MWD
Audio de-emphasis (for sound type " Mono wide" only)
Set the de-emphasis for the best sound impression to 50 s or J17.
µ
In the “Stereo“ and “Mono narrow“ audio modes, the de-emphasis “dnr" with “75
s" is selected automatically.
µ
Stereo, Mono narrow:
Mono wide:
dnr, 75 s
µ
50 s or J17
µ
Save the settings with the
key (press twice).
•
If you want to make new settings for further programme slots:
Change over to the “Video menu“ with the
key.
•
•
Move to the first menu line, “Programme slot“, and select the next programme
slot.
Select further programme slots in the same manner.
•
•
To exit the setup menu press the
key.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
Programmieren von Radio-Programmen
Programme providers are continually bringing out new radio programmes for
broadcast via the satellites. The “Radio“ menu allows you to store these pro-
grammes.
The settings for radio programmes in “Radio“ mode are carried out in the same
way as for the “TV“ mode.
Tuning in radio programmes
•
Switch from “TV mode“ into “Radio mode“ using the
key.
•
•
•
First select the programme slot that is to be programmed afresh.
Call up the radio menu by pressing the
Select the desired menu line using the
For direct numeric input use the keys
+
keys in succession.
keys.
•
...
or
•
•
•
Alter the values step-by-step with the
keys.
Press the
key twice in order to save your settings.
key.
Exit from the menu with the
The “radio” menu
The following settings can be made in the radio menu:
Ra d io p rog ra m m e :
R 02
Sa t fre q ue nc y:
Pola risa tion:
Orb it p osition:
De via tion:
11214 MHz
Hor. Lo w
1
16 MHz
Osc illa tor:
LO 1
Mod e :
STEREO
Fre q ue nc y:
De -e m p ha sis:
7.38/ 7.56 MHz
DNR/ 75µs
VOL 0-9 A/ B STOR STBY
The bottom line shows the keys you can use to make the settings.
Radio programmes are transmitted on sound subcarriers only. The setting to be
made is therefore either “Stereo“ or “Mono narrow“. Here the audio de-emphasis is
selected automatically as “DNR“ and 75 µs.
Note
You can terminate any setup procedure immediately (also without storing) by re-
turning to normal operation via the
key.Grundeinstellungen
In the initial setup menu, matching of the satellite receiver to the satellite receiving
system is carried out.
Important
The receiver has already been factory pre-programmed for standard satellite re-
ceiving systems.
Alterations to the initial setting are therefore necessary only if your receiving sys-
tem deviates from this type of installation or if you happen to want different set-
tings.
The settings in the initial setup menu are generally carried out by the specialist
dealer on installation of the satellite receiving system.
To prevent any unintentional alterations in the initial settings, the initial setup menu
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
can be invoked only from the switched-off state. (power supply interrupted).
Calling the initial setup menu
•
Withdraw the mains supply plug (inner hollow conductor plug) from the socket
(6).
•
Press both the programme selection buttons (4)
and keep them pressed.
on the infrared sensor
•
•
Insert the unit‘s mains supply plug again.
When the following screen menu appears release the keys
.
The initial setup menu is displayed.
>OSD la ng ua g e :
LNB sup p ly:
ENGLISH
ON
-in sta nd b y:
OFF
Prog ra m m e se le c tion:
OSD:
FREE
OFF
Osc illa tor m e nu...
DiSEq C m e nu ...
VOL 0-9 A/ B STOR STBY
The bottom line shows the keys you can use to make the settings.
Settings are made in the initial setup menu in the same manner as in the other
menus for the station programming:
•
•
Select menu entries with the
keys.
Carry out settings and call up submenus with the
(and use numeric keys 0-9 on inputting frequency).
keys
•
•
Press the
key twice to save your settings.
key.
Return with the
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
OSD language
Here you can select the language for the on-screen displays. The choice available
comprises: German and English and French.
Default: German
LNB supply voltage
Here you can turn off the power supply for the feed system if this is implemented
by an external power supply and signal selection is likewise not carried out by
means of the LNB supply voltage (e.g. Kathrein single-cable feed system UAS
330).
Default: ON
LNB supply voltage in standby
When the receiver is in standby the LNB supply voltage is normally switched off.
If terrestrial signals and satellite signals are combined in the receiving system, and
the power supply for the relevant components comes from the receiver, the power
supply must also be guaranteed when the receiver is in standby.
In this case switch the power supply in standby to “On“.
Default: “Off”.
Programme selection
You have the option of entering the programme number in one-, two-, or three-digit
form or in “free” form (Default: “free”).
Setting
Settable programme slots
One-digit input
Two-digit input
Three-digit input
Free input
Programme slots 1 to 9
Programme slots 1 to 99
Programme slots 1 to 200
Programme slots 1 to 200
On Screen Displays (OSD)
Here you can select whether the programme slot and programme name are to be
displayed continuously, or whether they are to be removed again approximately
three seconds after programme changeover..
This setting can be made differently in TV mode and radio mode.
Default:
TV mode
“Off”.
“On”.
Radio mode
To call the initial setup menu for radio, the receiver must be switched into radio
mode before being switched off. Then call the initial setup menu in the usual way.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
Oscillator frequency
The satellites radiate their programmes in a frequency range that satellite receivers
are unable to process. In the receiving system (known as the LNB - Low Noise
Block converter or LNC - Low Noise Converter) this frequency is converted into a
lower frequency that can be processed by satellite receivers.
The satellite transmission frequencies lie in the following ranges:
10700 ... 11700 MHz
11700 ... 12750 MHz
Low-band
High-band
The receiver‘s input frequency range, however, lies in the range: 920...2150 MHz.
Conversion of the higher frequencies into a lower frequency is achieved with the
aid of the oscillator frequency (LO frequency). Various oscillator frequencies are
used for the conversion according to the satellite frequency range and type of sys-
tem.
For Astra and Eutelsat receiving systems, this is generally 9.75 GHz (9750 MHz)
for the lower frequency band (low-band) and 10.6 GHz (10600 MHz). for the upper
frequency band (high-band). Older receiving systems still operate in the low-band
region with 10 GHz oscillator frequency.
The receiver calculates the frequency onto which it needs to tune by subtracting
the oscillator frequency from the satellite transmission frequency stored for each
programme.
As a result, you can easily install the UFD 345 on other receiving systems without
needing to reprogramme every single programme slot.
You only need to set up the particular oscillator frequencies that your receiving
system uses.
In the delivered state, the oscillator frequency is set to 9.75 GHz (9750 MHz) for all
of the LO groups (LO 1 to LO 4).
Changing the oscillator frequency
Call the initial setup menu (see paragraph: “Calling the initial setup menu“).
•
•
Using the keys move to menu entry
“Oscillator menu . . .”.
•
•
•
Call up the “Oscillator selection“ submenu using the
keys.
Move to line in which you want to alter the oscillator frequency (LO 1... LO 4) .
Using the numeric keys set the desired LO frequency in 5-digit form
(e.g. 09750).
The already pre-programmed LO frequencies listed below can be selected with the
keys
09610 09665 09750 09950 10000
10230 10259 10500 10600 10700
10750 11000 11125 11300 11450
•
•
Further oscillator frequencies are set up by the same method.
Press the key twice to save your settings.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
DiSEqC menu
Fundamentals of the DiSEqC signal (Digital Satellite Equipment Control)
In order to select the satellite signals different control signals are required.
Up until now, the 14/18V LNB supply voltage and the 22 kHz signal (superimposed
on the LNB supply voltage) have been sufficient for signal selection for the majority
of applications.
With these four control criteria it is possible to switch between horizontally and ver-
tically polarised signals, as well as between two satellites (multifeed reception).
With the extension of the frequency range to the 12 GHz region (high-band region
11.70 – 12.75 GHz) or for reception of more than two satellites, additional control
criteria are required for LNB selection and signal selection.
The “DiSEqC“ control signal has been developed by Eutelsat in collaboration with
Philips.
The “DiSEqC“ control signal is, in fact, a special form of modulation (pulse-width
modulation) of the already existing 22 kHz signal.
Here one can differentiate between:
•
DiSEqC tone burst
(also termed Simple DiSEqC or just DiSEqC)
•
•
DiSEqC 1.0
DiSEqC 2.0
The UFD 345 receiver is equipped with both the tone-burst signal and DiSEqC 1.0.
The setting required is dependent on the components of your receiving system.
Settings in the DiSEqC
•
Call the initial setup menu (see paragraph “Calling the initial setup menu“).
Using the keys move to menu entry “DiSEqC menu . . .“.
Activate the submenu “DiSEqC menu . . .“. using the keys
•
•
The following menu appears (factory preset):
DiSEq C SETTING S
>22KHz-Sig na l:
Tone Burst:
Hig h/ Lo w
OFF
DiSEq C:
OFF
DiSEq C Re p e a t:
Re m ote Fre q .:
OFF
1000 MHz
VOL 0-9 A/ B STOR STBY
The bottom line shows the keys you can use to make the settings.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
22 kHz signal
In this menu entry, you specify whether the 22 kHz signal is to be used to switch
between a satellite‘s lower and upper frequency range (low/high) or to switch be-
tween two satellite positions (Pos. A/B).
22 kHz: High/Low:
Freq. range
22 kHz
Low
High
Off
On
(Factory preset)
or
Orbit Pos.
22 kHz
22 kHz: Pos A/B:
1 and 3
2 and 4
Off
On
See also video setup menu, menu lines:
Polarisation and Orbit Position
Tone-burst and DiSEqC-signal
If more than four control criteria are needed in a receiving system, a
DiSEqC control signal is required.
Which of the two setting options is required: “Tone Burst“ or “DiSEqC“
depends on the components of the receiving system.
Thus take into account the specifications of the components present in the receiv-
ing system (switch-over matrices).
Tone burst
In the “Tone burst“ menu entry the following settings of the 22 kHz signal are pos-
sible:
Switching states on setting:
22 kHz signal
Tone burst
→
→
High/Low and
Pos. A/B:
Low
High
22 kHz
Off
On
Pos. 1
Pos. 2
Tone burst
Tone burst
0
1
Switching states on setting:
22 kHz signal →
Pos. A/B and
Tone burst → Opt. A/B
Pos.
Tone burst
22 kHz
1
2
3
4
0
0
1
1
Off
On
Off
On
DiSEqC
The switching options are further extended with the DiSEqC signal.
For an optimal setting, it is essential to know the switching criteria of the receiving
system.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial settings
Thus take into account the specifications of the DiSEqC matrices or get in touch
with the installer of the receiving system..
DiSEqC Repeat
Remote
If “DiSEqC components” are cascaded in a satellite receiving system (several
DiSEqC matrices are connected in series), the menu entry "DiSEqC Repeat" must
be switched to "On"
The “Remote” setting in the “DiSEqC” menu entry is intended for future applica-
tions.
If the UFD 345 receiver is operated in a receiving system with a “Subscriber-
controlled preprocessing system“ e.g. “Kathrein UFO mini digital”, Remote
must be set in the DiSEqC menu.
In this case, the corresponding transmission frequency is selected in menu entry
“Remote Frequency” in the range 920 to 2150 MHz. The satellite signal is trans-
mitted from the receiving system to the receiver on this frequency.
•
•
Press the
key twice to save your settings.
key (press twice).
Exit from the initial setup menu with the
Note
If you exit the menus without saving, the settings will be lost.
Switching over remote control’s command set
The remote control handset contains two command sets. This allows two receivers
of the 200/300 series to be operated independently in a room (not in conjunction
with a twin receiver).
For this purpose, programme one receiver on command set 1 and the second re-
ceiver on command set 2.
•
•
•
Switch on receiver 1 and switch off receiver 2 (with the mains switch on the unit
or interrupt the power supply).
− Press the
key and keep it pressed.
− Using the numeric keys enter “001”.
Switch receiver 1 off (with the mains switch on the unit or interrupt the power
supply) and switch receiver 2 on.
− Press the
key and keep it pressed.
− Using the numeric keys enter “002”.
Switch receiver 1 on once again.
− Press the
key and keep it pressed.
− Using the numeric keys enter “003”.
Note
Note
With the first two settings the remote control must be pointed towards the respec-
tive receiver which is switched on.
With the
key you can now switch between the two command sets A and B
(toggle function) and operate the two receivers in alternation.
On delivery command set 1 is always active.
If you are using only one receiver and the active command set has been switched
over inadvertently due to maloperation rendering the receiver inoperable, the re-
mote control can be switched back to command set 1 without difficulty. The proce-
dure for this has already been described above.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Ausstattungsmerkmale
The UFD 345 receiver is equipped with the following features:
•
•
•
•
-channel memory for TV programmes, freely programmable
200
99-channel memory for radio programmes, freely programmable
Low-threshold tuner for picture optimisation when reception is poor
Selectable oscillator frequencies allow troublefree matching to feed systems
with divergent oscillator frequencies.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Detachable infrared sensor permits concealed installation of the receiver
Dimensions are small
Radio button
Stereo / Dual tone switchover
Audio frequency range from 5.0 MHz to 8.8 MHz
Sound muting and volume control
Dynamic noise reduction (DNR) Wegener-Panda 1
Stereo reception
On-screen display (OSD) 3 languages (German, English, French)
22-kHz control signal, programmable
DiSEqC 1.0 and tone-burst control signal
LNB supply voltage can be turned off
Runs off 12-24 VDC for mobile use
Comes with additional power pack for mains operation
Connecting socket for data copying function
(programme data read-in and read-out with the “Copy Programmer”)
•
•
Programme swap, sort and copy functions
Infrared remote control with command set changeover (allowing operation of
two receivers in a room)
•
•
3 Scart sockets for TV-, VCR- and decoder connection
Last-status memory
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Technische Daten
UHF characteristics
Sat IF frequency range
950 to 2150 MHz
48 to 78 dBµV
479.5 MHz
Input level range
IF frequency
IF bandwidth
27 MHz
FM threshold
7 dB max.
Low threshold tuner
adjustable in 32 steps
Video
Audio
Frequency range
Deviation
20 Hz to 5 MHz
16/25 MHz
Output voltage
De-emphasis
1 Vss / 75Ω
CCIR Rec. 405 / 625 lines
Subcarrier frequency range
Bandwidth
5.0 to 8.8 MHz
- Mono wide
- Mono narrow / Stereo
280 kHz
130 kHz
Frequency range
De-emphasis Mono wide
Mono narrow
40 Hz to 15 kHz
50 µs / J17 programmable
DNR/75 µs Wegener Panda
1 V / into 10kΩ
Output voltage
Distortion factor
S/N
<1.0 % (at 1 kHz)
70 dB typ.
Power supply
Operating voltage
Power pack
12 – 24 V DC
230 V ±10%, 50 Hz, 1 A
Power consumption
Receiver (full-load / standby)
13 / 1 W
Receiver with power pack
(full-load / standby)
17 / 2 W
LNB supply voltage
LNB supply current
Control signal
0, +14 V (vert.), +18 V (hor.)
300 mA max.
22 kHz square-wave, 0.6 Vss
DiSEqC 1.0 / Tone burst
Connectors
Sat IF input
F socket 75Ω
TV / VCR / Decoder
Infrared sensor / Data interface
Supply voltage
3 Scart/Peritel sockets 21-way
Western socket 8-way
Low-voltage hollow plug
5.5/2.1 mm
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Unit dimensions (B/H/D)
271 / 50 / 150 mm
Weight
Receiver
Power pack
Approx. 0.6 kg
Approx. 0.76 kg
Temperature range
Accessories
Ambient temperature
+5 °C ... 40 °C
Power pack 230 V ∼/ 16 V=/1 A
Infrared sensor, Infrared remote control
Scart cables, 12 V connecting cable with universal plug 6-24 V DC
2x 1.5 V batteries, type: LR 03, size: AAA (micro)
Operating manual
Scart socket assignments
Signal
Pin No.
1
TV
VCR
X
Decoder
AUDIO Output Right
X
X
X
X
X
X
X
AUDIO Input Right
AUDIO Output Left
AUDIO Ground
2
X
3
X
X
X
X
4
X
BLUE Video Ground
AUDIO Input Left
BLUE Video
5
X
6
X
7
Function Switching
GREEN Video Ground
Commn. Data Line 2
GREEN Video
8
X
X
X
X
X
X
9
10
11
12
13
14
15
16
17
18
19
20
21
Commn. Data Line 1
RED Video Ground
Commn. Data Ground
RED Video
X
X
X
Blanking Signal
VIDEO Ground
X
X
X
X
X
X
X
X
X
X
X
X
X
Blanking Ground
VIDEO Output
VIDEO Input
Common Ground
X
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu structure
Menüstruktur
Video- and Audio Setup Menu
Re turn (ste pwise ) into norm a l p rog ra m m e mode with ke y
Sa ve se tting s with ke y
Se le c t m e nu e ntrie s with
Ma ke the se tting with
(p re ss twic e )
or with the nume ric ke ys for fre q ue nc y se tting
Cha ng e from Vid e o m e nu to Aud io m e nu with ke y
Cha ng e from Aud io m e nu to Vid e o m e nu with ke y
Possible setting:
Step on
to the next
programme slot
Programme slot
Programme name
maximum 5 chars
Programme name
Satellite frequency
Video Setup Menu
call up with
key STORE + VIDEO
Settable in range
from 10700...12747 MHz
Vert. Low, Vert. High
Hor. Low, Hor. High
Polarisation
Position
1, 2, 3 or 4
Orbit position
Video dev.
Oscillator
16 or 25 MHz
LO 1, 2, 3 or 4
Decoder setting
Signal path
Audio:
Decoder menu ...
internal or external
internal or external
Signal path
Video:
Video
Baseband PAL
Baseband MAC
Signal type:
Stereo/
Mono narrow
Mono wide
Audio
mode
Audio Setup Menu
call up with
key STORE + Audio
Audio
frequency
5.00 ....8.80 MHz
DNR (Stereo, Mono narrow)
50 us; J17 (Mono wide)
Audio
de-emphasis
"Audio de-emphasis"
only with
"Mono wide" active!
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu structure
Radio Setup Menu
Re turn (ste pwise ) into norm a l p rog ra m m e mode with ke y
Sa ve se tting s with ke y
Se le c t m e nu e ntrie s with
Ma ke the se tting with
(p re ss twic e )
or with the nume ric ke ys for fre q ue nc y se tting
Possible setting:
Step on
to the next
Programme slot
programme slot
Radio Setup Menu
call up with
key STORE + RADIO
Settable in the range
von 10700..12747 MHz
Satellite frequency
Vert. Low, Vert. High
Hor. Low, Hor. High
Polarisation
Orbit position
Video dev.
Oscillator
Position
1, 2, 3 or 4
16 or 25 MHz
LO 1, 2, 3 oder 4
Stereo/
Mono narrow
Mono breit
Audio
mode
Audio
frequency
5.00 ....8.80 MHz
Audio-
de-emphasis
DNR (Stereo, Mono narrow)
50 us / J 17 (Mono wide)
"Audio de-emphasis"
only with
"Mono wide" active!
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu structure
Initial Setup Menu
Re turn (ste pwise ) into norm a l p rog ra m m e mode with ke y
.
Sa ve se tting s with ke y S
Se le c t m e nu e ntrie s with
Ma ke the se tting with
(p re ss twic e ).
.
or with the nume ric ke ys for fre q ue nc y se tting .
Possible setting:
Call initial setup menu
Disconnect the power supply,
Press both CH buttons on infrared
and keep pressed,
OSD lang.
Ger, Eng, Fre
On, Off
,
Reconnect the power supply!
LNB supply
LNB supply
in standby
On, Off
1-, 2-, 3-digit
or free input
Prog. Selectn.
On-screen display
OSD
Off, On
Frequency range
9000 ... 12000
Oscillator menu...
LO 1
9000 ... 12000
9000 ... 12000
9000 ... 12000
LO 2
LO 3
LO 4
DiSEqC-
menu....
Off, High/Low
or Pos A/B
22 kHz
Tone Burst
DiSEqC
Off, Pos.A/B or
Opt. A/B
Off, On, Remote
DiSEqC Rept
Remote freq.
Off, On
920 .. 2150
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection example / Service note
Service note:
Dear Customer,
In the unlikely event that you should experience problems with your receiver,
please contact your local specialist dealer or our service organisation.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
KATHREIN-Werke KG telephone (++49)08031/1840 fax (++49)08031/184306
Anton-Kathrein-Straße 1-3 P.O.B. 10 04 44 D-83004 Rosenheim/Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
|