K 5.93 M
English
Please keep the original box, packaging and receipt. Before operating this unit,
please read this manual thoroughly and retain it for future reference.
5.961-547.0 02/05EN
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL OVERVIEW
Description of Items
11 Trigger gun safety lock
1 Power cord
12 Quattro nozzle
2 High pressure outlet
3 ON/OFF switch
13 Detergent dosing valve
ƽ CAUTION
4 Water inlet and filter inlet with gar-
den hose connector (not shown)
5 Detergent tank (removable)
6 Detergent suction tube with cap
7 Transport handle
8 Accessory compartment
9 High pressure hose
10 Trigger gun
Follow the maintenance instructions
specified in the manual
This machine has been designed for
use with cleaning detergents by the ma-
nufacturer. The use of other cleaning
detergents may affect the operation of
the machine and void the warranty.
For household use only !
English 3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
! The Trigger Gun Safety Lock PRE-
VENTS the trigger from accidentally
being engaged. This safety feature
DOES NOT lock trigger in the ON
position.
When using this product basic
precautions should always be
followed, including the following:
! Read all the instructions before
using the product.
ƽ WARNING
Do not spray electrical apparatus and
wiring.
Do not use with flammable liquids and
toxic chemicals.
Injection hazard: equipment can cause
serious injury if the spray penetrates the
skin. do not point the gun at anyone or
any part of the body. In case of penetra-
tion seek medical aid immediately.
This system is capable of producing
10500 kPa to avoid rupture and injury,
do not operate this pump with compon-
ents rated less than 10500 kPa working
pressure (including but not limited to
spray guns, hose and hose connec-
tions).
! To reduce the risk of injury, close su-
pervision is neccessary when a pro-
duct is used near children.
! Know how to stop the product and
bleed pressures quickly. Be thoroug-
hly familiar with the controls.
! Stay alert — watch what you are
doing.
! Do not operate the product when fa-
tigued or under the influence of alco-
hol or drugs.
! Keep operating area clear of all per-
sons.
! Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
! Follow the maintenance instructions
specified in the manual.
! Risk of Injection or Injury to persons
- Do not direct discharge stream at
persons.
Before servicing, cleaning or removing
any parts, shut off power and relieve
pressure.
Grounding Instructions
This product must be grounded. If it
should malfunction or breakdown,
! High pressure jets can be dangerous
if subject to misuse. The jet must not
be directed at persons, animals,
electrical devices, or the machine
itself.
grounding provides a path of least resi-
stance for electric current to reduce the
risk of electric shock. This product is
equipped with a cord having an equip-
ment-grounding conductor and a groun-
ding plug. The plug must be plugged
into an appropriate outlet that is proper-
ly installed and grounded in accordance
with all local codes and ordinances.
! Wear safety goggles.
! Do not use acids and solvents in this
product. These products can cause
physical injuries to the operator and
irreversible damage to the machine.
! To reduce the risk of electrocution,
keep all connections dry and off the
ground.
ƽ DANGER
Improper connection of the equipment-
grounding conductor can result in a risk
! Do not touch plug with wet hands.
4 English
Download from Www.Somanuals.com. All Manuals Search And Download.
of electrocution. Check with a qualified
electrician or service personnel if you
are in doubt as to whether the outlet is
properly grounded. Do not modify the
plug provided with the product - if it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician. Do not
use any type of adapter with this pro-
duct.
ƽ WARNING
To reduce the risc of electrocution, keep
all connections dry and off the ground.
Do not touch plug with wet hands.
WATER SUPPLY (Cold Water Only)
ƽ CAUTION
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
! Water hose must be at least 1/2 inch
or 5/8 inch in diameter.
! Flow rate of water supply must not
fall below 2 GPM (gallons per minu-
te).
! Flow rate can be determined by run-
ning the water for one minute into an
empty 5-gallon container.
! The water supply temperature must
not exceed 104°F/40°C.
! Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
! Always prevent debris from being
drawn into the unit by using a clean
water source.
Extension Cords
! Use only 3-wire extention cords that
have 3-prong grounding-type plugs
and 3-pole cord connectors that ac-
cept the plug from the product.
Up to 25 ft = 12/3 AWG;
25 to 50 ft = 10/3 AWG.
! Use only extension cords that are in-
tended for outdoor use. These ex-
tension cords are identified by the
marking “Acceptable for use with
outdoor appliances; store indoors
while not in use.”
! Use only extension cords having an
electrical rating not less than the ra-
ting of the product.
! Do not use damaged extension
cords.
! Examine extension cord before
using and replace if damaged.
! Do not abuse extension cord and do
not yank on any cord to disconnect.
! Keep cord away from heat and sharp
edges.
SAVE THESE
INSTRUCTIONS !
! Always disconnect the extension
cord from the receptacle before dis-
connecting the product from the ex-
tension cord.
!
If you are using an extension cord, it
should always be completely un-
wound from the cable drum.
English 5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
" STEP 1: Mount cover and secure
" STEP 4: Place detergent tank into
with 2 screws.
compartment.
" STEP 2: Attach the handle and se-
" STEP 5: Attach the high pressure
hose to the trigger gun.
cure with 4 screws.
Pull out the locking slide from the
right side of the trigger gun handle
(A), and insert the small end of the
high pressure hose into place (B).
Push the locking slide back into the
trigger gun (C) to lock the hose in po-
sition (D).
C
" STEP 3: Attach detergent suction
B
“clic”
tube to the detergent dosing valve.
A
D
6 English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
" STEP 1: Connect the high pressure " STEP 4: Connect garden hose to the
hose to the unit’s high pressure out-
let.
cold water source and turn water on
completely. Plug the power cord into
the power outlet.
" STEP 5: Unlock the Safety lock (A).
Trigger the gun (B) to eliminate trap-
ped air, wait for a steady flow of wa-
ter to emerge from the spray nozzle.
" STEP 2: Insert the spray wand to the
trigger gun. Press in against the
spring tension and twist into locked
position.
" STEP 6: Turn on the high pressure
washer (I).
The motor starts only if the trigger
of the gun is pulled and shuts off
when the trigger is released.
" STEP 3: Connect garden hose to
unit’s water inlet.
English 7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE ACCESSORIES
ƽ WARNING
To avoid serious injury never point
spray nozzle at yourself, other per-
sons or animals.
Quattro Nozzle
Note: The marking on the spray
lance must be up during operation.
Selecting the jet
" Release the trigger of the handgun.
" Rotate the nozzle head until the
symbol is aligned with the marking
on the spray lance.
8 English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING WITH DETERGENTS
Detergents can only be applied at
low pressure (Min).
For best results see Cleaning Tips on
pages 12 & 13 for specific informati-
" Turn Quattro Nozzle to Low pressu- on on how to clean different sur-
re position
.
faces.
" STEP 2: Fill the Detergent Tank with
the selected Ready To Use deter-
gent.
Always Use Kärcher Detergent for Best
Results
Kärcher biodegradable detergents are
specially formulated to protect the envi-
ronment and your pressure washer.
Special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a lon-
ger life. For Kärcher Detergents, check
your retailer or call our service center for
help.
" STEP 3: Adjust the detergent do-
sing valve.
The following Kärcher detergents are
available:
Turn to the left:
Meter detergent from container 1
Turn to the right:
Meter detergent from container 2
! Pressure wash
! Deck + Fence wash
! Degreaser
! Vehicle wash
ƽ CAUTION
Never use:
– Bleach, Chlorine products and other
corrosive chemicals
– Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
– Tri-sodium phosphate products
– Ammonia products
– Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
" STEP 4: Turn on the pressure was-
her (1). Pull trigger to operate unit:
Liquid detergent is drawn into the
unit and mixed with water. Apply de-
tergent to work area. Do not allow
detergent to dry on surface.
English 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTTING DOWN
STEP 1: Turn the switch to OFF (0) po- STEP 5: Disconnect the high pressure
sition and unplug cord from outlet.
hose from the high pressure outlet.
STEP 2: Turn off the water source.
STEP 3: Press trigger to release water
pressure.
STEP 6: Release trigger (A) and enga-
ge gun safety lock (B).
3
2
B
A
STEP 4: Disconnect the garden hose
from the water inlet on the unit..
TAKING A BREAK ..five minutes or more
STEP 1: Release trigger (A) and enga-
ge gun safety lock (B).
STEP 2: Turn pressure washer to off
(O) position.
10 English
Download from Www.Somanuals.com. All Manuals Search And Download.
WINTERIZING AND LONG-TERM STORAGE
" 1: Disconnect all water connections.
" 2: Turn on the machine for a few se-
conds, until the water which had
remained in the pump exits, turn off
immediately.
" 3: Do not allow high pressure hose
to become kinked.
" 4: Store the machine and accesso-
ries in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
ƽ CAUTION
Failure to follow the above directions
will result in damage to the pump as-
sembly and accessories.
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter
Maintenance
Pull out the water inlet filter with flat-
nose pliers and rinse out in warm water.
The unit is maintenance-free.
Cleaning the detergent inlet filter
Pull it out and rinse out in warm water.
English 11
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING TIPS
keeping the spray nozzle approximately
6 inches from the cleaning surface.
Deck Cleaning
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using Kärcher Deck Wash, ap-
ply to surface at low pressure. For best
results, limit your work area to smaller
sections of approximately 25 square
feet. Allow Deck Wash to remain on sur-
face 1-3 minutes. Do not allow deter-
gent to dry on surface. Rinse at high
pressure in a long sweeping motion
keeping the spray nozzle approximately
3-6 inches from the cleaning surface.
Always clean from top to bottom and
from left to right. When moving on to a
new section of the cleaning surface, be
sure to overlap the previous section to
eliminate stop marks and ensure a more
even cleaning result.
ƽ CAUTION
Do not use rotating jet on siding as it
may cause damage.
Cement Patios, Brick and Stone
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If
using Kärcher Pressure Wash or De-
greaser, apply to surface at low pressu-
re. For best results, limit your work area
to smaller sections of approximately 25
square feet. Allow Pressure Wash or
Degreaser to remain on surface 1-3 mi-
nutes. Do not allow detergent to dry on
surface. Rinse at high pressure in a
sweeping motion keeping the spray
nozzle approximately 3-6 inches from
the cleaning surface. Always clean from
ƽ CAUTION
Do not use rotating jet on wood surfaces top to bottom and from left to right. For
as it may cause damage.
removing extremely stubborn stains,
use the rotating jet.
House Siding
Cars, Boats & Motorcycles
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If
(with or without detergent). Pre-rinse
using Kärcher Pressure Wash, apply to vehicle with fresh water. If using Kär-
surface at low pressure (for best results, cher Vehicle Wash, apply to surface at
limit your work area to sections of ap-
proximately 6 feet and always apply de- one side of vehicle at a time and always
tergent from bottom to top). Allow apply detergent from bottom to top, do
low pressure. For best results, clean
Pressure Wash to remain on surface 1- not allow detergent to dry on surface. If
3 minutes. Do not allow detergent to dry needed, use special wash brush attach-
on surface, if surface appears to be
drying, simply wet down surface with
ment to remove stubborn dirt. Rinse at
high pressure in a sweeping motion
fresh water. If needed, use special wash keeping the spray nozzle approximately
brush attachment to remove stubborn
dirt. Rinse at high pressure from top to
bottom in an even sweeping motion
6-8 inches from the cleaning surface (di-
stance should increase when rinsing
pin-striping or other sensitive surfaces).
Always clean from top to bottom and
12 English
Download from Www.Somanuals.com. All Manuals Search And Download.
from left to right. For best results, wipe
surface dry with a chamois or soft dry
cloth.
Patio & Lawn Furniture
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using Pressure Wash, ap-
ply to surface at low pressure. Allow
Pressure Wash to remain on surface 1-
3 minutes. Do not allow detergent to dry
on surface. If needed use special Wash
Brush Attachment to remove stubborn
dirt. Rinse at high pressure in a
ƽ CAUTION
Do not use rotating jet on vehicles as it
may cause damage.
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If
using Kärcher Pressure Wash or De-
greaser, apply detergent at low pressu-
re. Allow Pressure Wash to remain on
surface 1-3 minutes.Do not allow deter-
gent to dry on surface. Rinse at high
pressure keeping the spray nozzle ap-
proximately 3-6 inches from the cle-
aning surface. For removing extremely
stubborn dirt, it may be necessary to
move the spray nozzle even closer to
the surface for greater dirt cutting ac-
tion.
sweeping motion keeping the spray
nozzle approximately 3-6 inches from
the cleaning surface. For best results,
clean from top to bottom and from left to
right.
ƽ CAUTION
Do not use rotating jet on patio or lawn
furniture as it may cause damage.
Recommendations
! Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
! If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
ƽ CAUTION
Do not use rotating jet on cloth, plastic
or other sensitive surfaces as it may
cause damage.
! When using on surfaces which might
come in contact with food, flush sur-
faces with plenty of drinking water.
OPTIONAL CLEANING ACCESSORIES
Optional cleaning accessories are
available to further enhance your cle-
aning capabilities: For details call 1-
! Rotating Wash Brush
! Sandblasting Attachment
! Extension Wand
! Water Siphon Kit
! 25 Ft. Extension Hose
! T-Racer
! Wash Brush
! Underbody Wand
! Pipe Drain Cleaner
English 13
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Disconnect the machine from the power
source before making any repair.
ƽ CAUTION
Symptom
Cause
Solution
Motor will not start
On/Off switch is in the “OFF”
(O) position.
Turn switch to the “ON” (I) posi-
tion
Power cord is not plugged in.
Extension cord is too long.
Plug in power cord.
Replace extension cord with
either a 25 ft. 12/3 gauge cord
or a 50 ft. 10/3 gauge cord.
Extension cord is not proper
gauge.
Extension cord is damaged.
Electrical outlet does not supply Try a different outlet.
adequate power.
Unit does not reach
high pressure.
Diameter of garden hose is too Replace with a 1/2 inch or 5/8
small.
inch garden hose.
Water supply is restricted.
Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Spray wand is in low pressure Turn spray wand to high pres-
position. sure position.
Output pressure va-
ries high and low.
Not enough inlet water supply. Turn water on full force. Check
garden hose for kinks, leaks or
blockage.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Discharge nozzle is obstructed. Blow out or remove debris with
a fine needle.
Calcified gun, hose or spray
wand.
Run distilled vinegar through
detergent suction tube.
14 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Solution
No detergent.
Detergent suction tube not pro- Check connection.
perly connected to the machi-
ne.
Detergent is too thick.
Dilute detergent, for best resul-
ts use Kärcher detergent.
Filter on detergent suction tube Run warm water through filter
is clogged. to remove debris.
Damaged or clogged detergent Remove obstruction or replace
suction tube. detergent suction tube.
Spray wand is in high pressure Turn spray wand tip to low pres-
position. sure position.
Discharge nozzle is obstructed. Blow out or remove debris with
fine needle.
Garden hose connec- Loose fittings.
tion leaks.
Tighten fittings.
Missing/worn rubber washer.
Insert new washer.
Spray wand leaks.
Spray wand not properly atta-
ched.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic insert. Call Customer Service.
Pump is noisy.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water leaks from
pump (up to 10 drops
per minute is permis-
sible).
Loose fittings.
Check that all fittings are tight.
Call Customer Service.
Water seals are damaged or
worn.
Oil Drip.
Oil seals are damaged or worn. Call Customer Service.
Kärcher Customer Service CDN
Call: 1-800-465-4980 for help or visit
our website: www.karcher.ca
If you encounter any additional difficul-
ties not listed, please call for help.
English 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Kärcher Customer Service CDN
Call: 1-800-465-4980 for help or visit
our website: www.karcher.ca
Download from Www.Somanuals.com. All Manuals Search And Download.
|