K 2.350
English
Español
Français
2
19
36
59633970 09/09
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL OVERVIEW
1 High pressure outlet
2 ON/OFF switch
9 Wheels
10 Trigger gun
3 Hose/Cord Hook
11 Trigger gun safety lock
4 Handle
12 Locking slide for high pressure hose
13 High pressure hose
14 Dirtblaster (Rotary spray wand)
5 Spray Wand Storage
6 Water inlet with garden hose
connector
®
15 Vario Power Spray wand
7 Detergent suction tube with filter
8 Power cord with Ground Fault Circuit
Interrupter (GFCI)
English 3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
physical injuries to the operator and
irreversible damage to the machine.
ƽ WARNING
When using this product basic precau-
tions should always be followed, includ-
ing the following:
ƽ CAUTION
Gun Kicks Back – Hold with both
hands.
„ Read all the instructions before using
the product.
„ To reduce the risk of injury, close su-
pervision is necessary when a prod-
uct is used near children.
„ Know how to stop the product and
bleed pressures quickly. Be thor-
oughly familiar with the controls.
„ Stay alert – watch what you are do-
ing.
„ The Trigger Gun Safety Lock pre-
vents the trigger from accidentally
being engaged. This safety feature
DOES NOT lock trigger in the ON po-
sition.
ƽ WARNING – Risk of Electrocution
„ Inspect cord before using – Do not
use if cord is damaged.
„ Keep all connections dry and off the
ground.
„ Do not operate the product when fa-
tigued or under the influence of alco- „ Do not touch plug with wet hands.
hol or drugs.
„ Do not use extension cord with this
„ Keep operating area clear of all per-
sons.
product.
„ Connect to individual branch circuit
„ Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
only.
ƽ CAUTION
This unit has been designed for use with
„ Follow the maintenance instructions cleaning detergents recommended by
specified in the manual.
the manufacturer. The use of other
„ This product is provided with a
cleaning detergents may affect the oper-
Ground Fault Circuit Interrupter built ation of the machine and void the war-
into the power cord plug. If replace-
ment of the plug or cord is needed,
use only identical replacement parts.
ranty.
ƽ WARNING
„ DO NOT SPRAY ELECTRICAL APPA-
RATUS AND WIRING.
ƽ WARNING
Risk of Injection or Injury – Do Not
Direct Discharge Stream At Persons. „ DO NOT USE WITH FLAMMABLE
„ High pressure jets can be dangerous
if misused. The jet must not be di-
rected at persons, animals, electrical
devices, or the unit itself.
LIQUIDS AND TOXIC CHEMICALS.
„ HIGH PRESSURE. KEEP CLEAR OF
NOZZLE.
„ INJECTION HAZARD: EQUIPMENT
CAN CAUSE SERIOUS INJURY IF
THE SPRAY PENETRATES THE
SKIN. DO NOT POINT THE GUN AT
ANYONE OR ANY PART OF THE
BODY. IN CASE OF PENETRATION
SEEK MEDICAL AID IMMEDIATELY.
„ Wear safety goggles.
ƽ WARNING
Risk Of Explosion – Do not spray
flammable liquids.
„ Do not use acids, alkaline, solvents,
or any flammable material in this
product. These products can cause
4 English
Download from Www.Somanuals.com. All Manuals Search And Download.
„ THIS SYSTEM IS CAPABLE OF PRO- to the parts they replace. A doubleinsu-
DUCING 1600 PSI TO AVOID RUP-
TURE AND INJURY, DO NOT
OPERATE THIS PUMP WITH COM-
lated product is marked with the words
“DOUBLE INSULATION” or “DOUBLE
INSULATED”. The symbol “ ” may also
PONENTS RATED LESS THAN 1600 be marked on the product.
PSI WORKING PRESSURE (INCLUD-
ING BUT NOT LIMITED TO SPRAY
GUNS, HOSE AND HOSE CONNEC-
TIONS).
WATER SUPPLY
(Cold Water Only)
ƽ CAUTION
„ BEFORE SERVICING, CLEANING
OR REMOVING ANY PARTS, SHUT
OFF POWER AND RELIEVE PRES-
SURE.
„ IF CONNECTION IS MADE TO A PO-
TABLE WATER SYSTEM, THE SYS-
TEM SHALL BE PROTECTED
AGAINST BACKFLOW.
When connecting the water inlet to the
water supply mains, local regulations of
your water company must be observed.
In some areas the unit must not be con-
nected directly to the public drinking wa-
ter supply. This is to ensure that there is
no feedback of chemicals into the water
supply. Direct connection via a receiver
tank or backflow preventer, for example,
is permitted.
GROUND FAULT CIRCUIT
INTERRUPTER PROTECTION
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
„ Garden hose must be at least 1/2
inch or 5/8 inch in diameter.
„ Flow rate of water supply must not
fall below 2 GPM (gallons per
minute).
„ Flow rate can be determined by run-
ning the water for one minute into an
empty 5-gallon container.
This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI)
built into the plug of the power-supply
cord. This device provides additional
protection from the risk of electric shock.
Should replacement of the plug or cord
become necessary, use only identical
replacement parts that include GFCI
protection.
„ The water supply temperature must
not exceed 104°F/40°C.
„ Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
„ Always prevent debris from being
drawn into the unit by using a clean
water source.
SERVICING OF A DOUBLE-
INSULATED PRODUCT
In a double-insulated product, two sys-
tems of insulation are provided instead
of grounding. No grounding means is
provided on a double-insulated product,
nor should a means for grounding be
added to the product. Servicing a dou-
ble-insulated product requires extreme
care and knowledge of the system, and
should be done only by qualified service
personnel. Replacement parts for a dou-
ble-insulated product must be identical
SAVE THESE INSTRUCTIONS!
English 5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
Î STEP 3:
A Pull out the locking slide of the trigger
Required tools
Screwdriver, small size (not supplied)
for connecting high pressure hose and
trigger gun.
gun handle.
B Insert the small end of the high pres-
sure hose into place.
C Push the locking slide back into the
trigger gun to lock the hose in posi-
tion.
Assembly
Î STEP 1:
Insert wheels into the side holes of
the unit.
Î STEP 2:
Slide the transport handle into place.
OPERATING INSTRUCTIONS
Î STEP 1:
Connect the high pressure hose to
the unit’s high pressure outlet.
Î STEP 2:
Insert the spray wand of your choice
into the trigger gun. Press in against
the spring tension and twist into
locked position.
6 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Î STEP 3:
Connect garden hose to unit’s water
Î STEP 6:
Unlock the trigger gun safety lock.
inlet.
Trigger the gun to eliminate trapped
air, wait for a steady flow of water to
emerge from the spray nozzle.
Î STEP 4:
Connect garden hose to the cold wa-
ter source and turn water on com-
pletely.
Î STEP 7:
Turn on the high pressure washer (I/
ON).
The motor starts only if the trigger
of the gun is pulled and shuts off
when the trigger is released.
Î STEP 5:
Plug the Ground Fault Circuit Inter-
rupter (GFCI) into a receptacle.
Press RESET button, indicator
should be “ON”.
Press TEST button, indicator should
be “OFF”.
Press RESET button for use.
We recommend that you test the GFCI as
part of your startup procedure each time
you use your pressure washer. To learn
how to peform this test on your unit, visit
gfci_test.php for detailed instructions for
your type of GFCI.
ƽ WARNING
Do not use if above test fails.
English 7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE ACCESSORIES
ƽ WARNING
Dirtblaster®
To avoid serious injury never point
spray nozzle at yourself, other per-
sons or animals.
„ This nozzle features a 0º pencil jet
which rotates 360º for maximum dirt
cutting action, effectively increasing
cleaning performance up to 50%.
This nozzle combines the cleaning
performance of a 0º pencil jet with
the surface coverage of a wide angle
nozzle.
Always test an inconspicuous area
before cleaning with high pressure.
Vario Power Spray Wand
„ The Vario Power Spray Wand allows
you to adjust the cleaning pressure.
To clean at maximum pressure, the
wand must be positioned to the high
pressure setting (Max).
Not recommended for soft materi-
als, siding, painted surfaces,
decks or autos.
For reduced pressure turn the wand
collar in the „Min“ direction.
To apply detergent, the wand must
be positioned to the low pressure
setting (Mix).
„ Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
8 English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING WITH DETERGENTS
Detergents can only be applied at low For best results see Cleaning Tips for
pressure (Min.).
Î STEP 1:
specific information on how to clean
different surfaces.
Install the Vario Power Spray Wand.
Set the spray wand to the low pres-
sure setting (Mix).
®
Always Use Kärcher Detergent for
Best Results
®
Kärcher biodegradable detergents are
specially formulated to protect the envi-
ronment and your pressure washer. The
special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a longer
®
life. For Kärcher Detergents, check
your retailer or visit our website:
Î STEP 2:
Fill a container with Kärcher deter-
gent. Place the filter end of detergent
suction tube into the container.
ƽ CAUTION
Never use:
–
Bleach, Chlorine products and other
corrosive chemicals
–
Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
Tri-sodium phosphate products
Ammonia products
–
–
–
Acid-based products
Î STEP 3:
These chemicals will harm the unit and
will damage the surface being cleaned.
Use of these items will void the war-
ranty.
Turn on the pressure washer (I). Pull
trigger to operate unit. Liquid deter-
gent is drawn into the unit and mixed
with water. Apply detergent to work
area. Do not allow detergent to dry
on surface.
Î STEP 4:
To rinse, move the VPS out of „Mix“
position and pull trigger to operate
unit.
Î STEP 5:
Cleaning up: Always draw fresh wa-
ter through the detergent tank or si-
phon tube when done to flush any
remaining detergents from the injec-
tion system.
English 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING A BREAK ..five minutes or more
Î STEP 1:
Release trigger and engage gun
safety lock.
Î STEP 2:
Turn pressure washer to OFF (0) po-
sition.
SHUTTING DOWN & CLEAN-UP
Î STEP 1:
Turn the switch to OFF (0) position
and unplug cord from outlet.
Î STEP 5:
Disconnect the garden hose from the
water inlet on the unit.
Î STEP 2:
Turn off the water source.
Î STEP 6:
Disconnect the high pressure hose
from the high pressure outlet.
Î STEP 3:
Press trigger to release water pres-
sure.
Î STEP 4:
Release trigger and engage gun
safety lock.
10 English
Download from Www.Somanuals.com. All Manuals Search And Download.
WINTERIZING AND LONG-TERM STORAGE
Î 1: Disconnect all water connections.
Î 2: Turn on the machine for a few sec- Failure to follow the above directions will
ƽ CAUTION
onds, until the water which had re-
mained in the pump exits, turn off
immediately.
result in damage to the pump assembly
and accessories and will void the war-
ranty.
®
Î 3: Do not allow high pressure hose to Kärcher also recommends the regular
become kinked.
practice of using a pump protector like
“Kärcher Pump Guard” to prevent cold
weather damage during storage in the
winter months.
®
Î 4: Store the machine and accesso-
ries in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter
Maintenance
Î STEP 1:
The unit is maintenance-free.
Pull out washer from the water inlet.
Î STEP 2:
Pull out water inlet filter with flat-nose
pliers.
Î STEP 3:
Rinse out water inlet filter in warm
water.
Î STEP 4:
Reinsert water inlet filter and washer
into the water inlet.
English 11
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING TIPS
work area to sections of approximately
ƽ CAUTION
6 feet and always apply detergent from
bottom to top). Allow detergent to re-
main on surface 1-3 minutes. Do not al-
low detergent to dry on surface, if
„ Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
surface appears to be drying, simply wet
down surface with fresh water. If need-
ed, use special wash brush attachment
(not included) to remove stubborn dirt.
Rinse at high pressure from top to bot-
tom in an even sweeping motion keep-
ing the spray nozzle approximately
6 inches from the cleaning surface.
„ If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
„ When using on surfaces which might
come in contact with food, flush sur-
faces with plenty of drinking water.
„ For additional cleaning tips and a
complete video library, visit our web-
site:
Cement Patios, Brick and Stone
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, apply to
surface at low pressure. For best re-
sults, limit your work area to smaller sec-
tions of approximately 25 square feet.
Allow detergent or Degreaser to remain
on surface 1-3 minutes. Do not allow de-
tergent to dry on surface. Rinse at high
pressure in a sweeping motion keeping
the spray nozzle approximately 3-6
inches from the cleaning surface. Al-
ways clean from top to bottom and from
left to right. For removing extremely
Deck Cleaning
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using detergent, apply to sur-
face at low pressure. For best results,
limit your work area to smaller sections
of approximately 25 square feet. Allow
detergent to remain on surface 1-3 min-
utes. Do not allow detergent to dry on
surface. Rinse at high pressure in a long
sweeping motion keeping the spray noz-
zle approximately 3-6 inches from the
cleaning surface. Always clean from top
to bottom and from left to right. When
moving on to a new section of the clean-
ing surface, be sure to overlap the previ-
ous section to eliminate stop marks and
ensure a more even cleaning result.
®
stubborn stains, use the Dirtblaster
Nozzle.
Cars, Boats & Motorcycles
(with or without detergent). Pre-rinse
vehicle with fresh water. If using deter-
gent, apply to surface at low pressure.
For best results, clean one side of vehi-
cle at a time and always apply detergent
from bottom to top, do not allow deter-
gent to dry on surface. If needed, use
special wash brush attachment (not in-
cluded) to remove stubborn dirt. Rinse
House Siding
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent, apply to surface at low
pressure (for best results, limit your
12 English
Download from Www.Somanuals.com. All Manuals Search And Download.
at high pressure in a sweeping motion
keeping the spray nozzle approximately tremely stubborn dirt, it may be neces-
6-8 inches from the cleaning surface
sary to move the spray nozzle even
cleaning surface. For removing ex-
(distance should increase when rinsing closer to the surface for greater dirt cut-
pin-striping or other sensitive surfaces). ting action.
Always clean from top to bottom and
Patio & Lawn Furniture
from left to right. For best results, wipe
surface dry with a chamois or soft dry
cloth.
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using detergent, apply to
surface at low pressure. Allow detergent
to remain on surface 1-3 minutes. Do
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(with or without detergent). Pre-rinse not allow detergent to dry on surface. If
cleaning surface with fresh water. If us- needed use special Wash Brush Attach-
ing detergent or Degreaser, apply deter- ment (not included) to remove stubborn
gent at low pressure. Allow detergent to dirt. Rinse at high pressure in a sweep-
remain on surface 1-3 minutes. Do not
ing motion keeping the spray nozzle ap-
allow detergent to dry on surface. Rinse proximately 3-6 inches from the
at high pressure keeping the spray noz- cleaning surface. For best results, clean
zle approximately 3-6 inches from the
from top to bottom and from left to right.
OPTIONAL CLEANING ACCESSORIES
Optional accessories are available to
further enhance your cleaning capabili-
ties. These accessories are accurate as
of the printing date of this manual.
25 Ft. Extension /Replacement
High-Pressure Hose
®
Replacement hose fits Kärcher pres-
Please check our website for pricing and sure washer with screw-on type gun
up-to-date information.
connections from 2400 PSI to 2500 PSI,
Extension Hose for all Kärcher high
®
Pump Guard
pressure washers between the original
equipment hose and machine up to
2500 PSI.
Specially formulated to protect your
pressure washer from freezing, corro-
sion and premature wear. The Pump
Guard also adds lubrication to valves
and seals to prevent sticking. Highly rec-
Part No. 2.640-850.0
66" Extension Wand (Four piece)
Need to clean second story windows or
other high areas? Increase the reach of
your pressure washer by up to 66" with
this extension kit. Includes 4 aluminum
sections for variable length. 66" fully as-
®
ommended for all Kärcher pressure
washers!
Part No. 9.558-998.0
®
sembled. Fits most Kärcher pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-746.0
English 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotating Wash Brush (bayonet)
Wet Sandblasting Kit (bayonet)
For more effortless cleaning of all
Why spend hours stripping old paint and
smooth surfaces (painted, glass and
plastic) try the Kärcher Rotating Wash the Kärcher Wet Sandblasting Kit do
Brush. Use it on your automobile, house the work! Attach the kit to your pressure
rust by hand using harsh chemicals? Let
®
®
siding or windows. The water pressure
from your pressure washer causes the
inner brushes to gently spin, making
washer, add abrasive material and at-
tack the rust and paint with our eco-
friendly alternative. Fits most Kärcher
®
your cleaning job much easier. The an- pressure washers up to 2300 PSI. (bay-
gle of brush head is adjustable to help
you reach difficult areas. Excellent for
the application of detergent. A must-
onet)
Part No. 2.638-792.0
®
Detergent Foamer Attachment
have accessory designed for Kärcher
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.640-743.0
Ideal for applications which require a
thick foam. Simply fill the resevoir cup
with liquid pressure washer detergent to
generate a foam spray. Connects direct-
Soft Clean Washing Brush
®
ly to the trigger gun. Fits most Kärcher
Made with soft bristles that will not harm pressure washers up to 2300 PSI. (bay-
painted surfaces. Easily attaches direct- onet)
ly to the trigger gun. Ideal for stubborn
dirt on cars, boats, patio furniture and
other surfaces. Great for applying deter-
gent. Fits most Kärcher pressure wash-
ers up to 2300 PSI. (bayonet)
Part No. 6.964-507.0
T 100 Wide Area Surface Cleaner
®
For cleaning surfaces such as patios,
terraces and driveways without splash-
back, there is no better solution than the
Part No. 2.640-740.0
®
Kärcher T 100. It saves time by clean-
25 ft. Pipe Cleaning Kit (bayonet)
ing a one foot wide area gently as it hov-
ers, providing consistent, streak-free
Need to clean blocked pipes, drains or
®
downspouts? The Kärcher pipe clean- cleaning. When you finish cleaning the
ing kit is the answer! The pipe cleaner
propels itself forward while simulta-
neously flushing out debris. For exam-
ple, insert the cleaning nozzle in the
patio and driveway, remove the wand
and use the handle to clean garage
doors and other vertical surfaces. In-
cludes two nozzles which spin at high
base of a downspout, pull the trigger on speed for optimum results. Our top sell-
®
the pressure washer gun and watch as
the nozzle shoots out leaves and other
ing accessory for Kärcher pressure
washers up to 2300 PSI. (bayonet)
debris while climbing upward. Connects Part No. 2.640-959.0
directly to the trigger gun of most
®
Kärcher pressure washers up to
2300 PSI. (bayonet)
Part No. 2.640-747.0
14 English
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
ƽ CAUTION
Disconnect the machine from the power
source before making any repair.
Symptom
Motor will not start On/Off switch is in the “OFF” Turn switch to the “ON” (I)
(0) position. position
Power cord is not plugged in. Plug in power cord.
Cause
Solution
Electrical outlet does not
supply adequate power.
Try a different outlet.
Tripped GFCI plug.
Press “RESET” button on GFCI
plug.
Unit does not
reach high
pressure.
Diameter of garden hose is
too small.
Replace with a 5/8 inch or
larger garden hose.
Water supply is restricted.
Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Spray wand is on low
pressure position.
Turn spray wand to high
pressure position.
Output pressure Not enough inlet water supply. Turn water on full force. Check
varies high and
low.
garden hose for kinks, leaks or
blockage.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Discharge nozzle is
obstructed.
Blow out or remove debris with
a fine needle.
Calcified gun, hose or spray Run distilled vinegar through
wand. detergent suction tube.
English 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Solution
No detergent.
Detergent is too thick.
Dilute detergent, for best re-
sults use Kärcher detergent.
®
Filter on detergent suction
tube is clogged.
Run warm water through filter
to remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand is in high
pressure position.
Turn spray wand tip to low
pressure position.
Discharge nozzle is
obstructed.
Blow out or remove debris with
fine needle.
Garden hose
Loose fittings.
Tighten fittings.
connection leaks.
Missing/worn rubber washer. Insert new washer.
Spray wand leaks. Spray wand not properly
attached.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic insert. Call Customer Support
Pump is noisy.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water leaks from Loose fittings.
Check that all fittings are tight.
pump (up to 10
drops per minute
is permissible).
Water seals are damaged or Call Customer Support
worn.
Oil Drip.
Oil seals are damaged or
worn.
Call Customer Support
If you encounter any additional difficul-
ties not listed, please visit our website.
USA / Canada:
México:
16 English
Download from Www.Somanuals.com. All Manuals Search And Download.
|