Slimline Silent
Convection
Panel Heater
Instruction Booklet
KPH200
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
1
4/12/09 2:01 PM
Contents
Kambrook Recommends
Safety First
p4
Your Convection Panel Heater
p6
p7
Hints/Tips to Retain
Heat in Your Home
Using Your Convection
Panel Heater
p8
Operating Instructions
Care and Cleaning
Warranty Details
p10
p11
p12
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
3
4/12/09 2:01 PM
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
Convection Panel Heater
• Carefully read all instructions before
operating the Convection Panel Heater
and save for future reference.
controls and at the power outlet then
unplug heater from the power outlet
when not in use.
• Remove any packaging material
and promotional stickers before using
the Convection Panel Heater for the
first time.
• Connect only to 230V or 240V
power outlet.
• Avoid touching heater body while it is on,
some parts of the heater are hot.When
moving the unit switch off and hold the
heater by the handles where provided.
• Keep combustible materials such as
drapes and other furnishings at least
1.7 metres from the front, sides and rear
of the heater. Do not use heater to dry
your laundry.
• Do not operate heater whilst asleep.
• Do not operate any heater with a
damaged cord or plug, or if heater
has been dropped or damaged in
any manner. Return heater to your
nearest Kambrook Service Centre for
examination, electrical or mechanical
adjustment or repair.
• Do not use outdoors. This heater is not
intended for commercial use, such as
construction sites.
• Do not locate the heater immediately
below a socket outlet when in use.
• Do not use this heater with a programmer,
timer or any other device that switches
the heater on automatically. Since a fire
risk may exist if the heater is covered or
positioned incorrectly.
• Do not cover the heater whilst it
is operating.
• This heater is not intended for use in
wet or moist locations. Do not use this
heater in the immediate surroundings of
a bath, a shower or a swimming pool.
Do not immerse or allow liquids to be
spilt on heater.
WARNING: In order to
avoid overheating do
not cover the heater.
• This heater has hot and arcing or
sparking parts inside. Do not use in
areas where petrol, paints, aerosols, or
other inflammable substances are used
or stored.
• Extreme caution and supervision is
necessary when this heater is used by
or near children, invalids or animals.
• Do not leave heater unattended.
Always switch off the heater at the
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
4
4/12/09 2:01 PM
• Do not operate the heater with the
power cord damaged, frayed or split,
wound around any part of the heater,
or in contact with heated surfaces of
the heater.
at the rear, top and sides) and do
not totally or partially block the air
inlet or outlets in any manner. Check
the openings from time to time for
accumulated dust.
• Do not allow materials that have been
in contact with oil, petroleum based
products or drying fluids to come in
contact with the heater.
• Do not run the cord under carpeting or
cover the cord with rugs, runners or the
like.Arrange cord away from traffic areas
and where it will not be tripped over.
• To disconnect heater turn the control
switch to ‘OFF’. Turn off at the power
outlet then remove the plug from
its outlet.
• Do not insert or allow foreign objects
to pass through the inlet or outlet
openings. This may cause an electric
shock, fire or damage the heater.
• Do not touch hot metal surfaces.
• Switch ‘OFF’ at the control switch and
power outlet, then unplug and allow
heater to cool down before cleaning
or storing.
• Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacturer
may cause fire electric shock or injury
and voids all warranties.
• Regularly inspect the supply cord, plug,
control settings, air inlets and outlets
and main housing for any damage in
any way. Immediately cease use of the
heater and return to Kambrook or an
authorised service agent for inspection
or repair.
• To prevent a possible fire or heat
damage, allow ample space around
the heater (1.7m at front and 0.5m
Important Safeguards For All
Electrical Appliances
• Fully unwind the power cord before use.
• Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre.
• Do not let the power cord hang over
the edge of a bench or table, touch hot
surfaces or become knotted.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• The installation of a residual current
device (safety switch) is recommended
to provide additional safety protection
when using electrical appliances. It
is advisable that a safety switch with
a rated residual operating current
not exceeding 30mA be installed in
the electrical circuit supplying the
appliance. See your electrician for
professional advice.
• The appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect
the appliance. To avoid a hazard do
not use the appliance if power cord,
power plug or appliance becomes
damaged in any way. Return the entire
appliance to the nearest authorised
Kambrook Service Centre for
examination and/or repair, or contact
Customer Service on 1300 139 798.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
5
4/12/09 2:01 PM
Your Convection Panel Heater
1. 2000 watt heating element
2. Removable feet for
wall mounting
Not Shown
•
•
3 heat settings
Wall mountable brackets
6
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
6
4/12/09 2:01 PM
Hints/Tips to Retain Heat in Your Home
•
•
Don’t overheat your home. The
temperature of a heated room in
winter should be 18-21°C
Your heater will work more
efficiently if you stick to
Kambrook’s recommended
clearance spaces
•
•
Choose the right size heater for
the room type you want to heat
Zone off unoccupied rooms by
closing doors and only heat the
main living areas
•
•
Fit window coverings like curtains
to halve winter heat loss
Put draft stoppers, such as a
rolled up towel, at the bottom
of outside doorways to keep out
cold air
•
•
Keep the heat in and the
cold out by installing wall and
ceiling insulation.
Avoid placing items too close to
the heater (both at the front and
back) for optimal air flow
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
7
4/12/09 2:01 PM
Using Your Convection Panel Heater
•
Turn the heater upright so that
the plastic feet are holding up
the heating unit.
Before First Use
Remove your heater from its carton
and associated protective wrapping.
Unwind the cord to its full length and
remove any protective cardboard or
foam that may have been used to
minimize transportation damage.
Wall Mounting Instructions
Please ensure your wall is capable
of holding the weight of this heater
and that the right screws are used
for your wall.
How to Operate
This unit can be mounted on any
wall in any room of the home. When
selecting a location, decide upon a
position that takes advantage of the
maximum volume of air.
The KPH200 can be either wall
mounted or used on the floor.
Relevant brackets and feet come
with the unit. For wall mounting
operation, follow instructions under
Wall Mounting Instructions.
CAUTION: Before
Floor Use Instructions
mounting the heater
to the wall please
1. Place the heater on a firm,
level surface in a stable upright
position and secure the supplied
feet with the screws provided.
ensure that all three
attachment points are
secure in either timber
or concrete. Do NOT
secure directly into
plaster. Please contact
a tradesman if you are
unsure.Please see the
Fig. 1 which illustrates
the points of contact.
Ensure that the heater
is at least 500mm from
the floor and corners of
the wall.
2. Visually inspect the air inlet and
outlets to ensure no foreign
material is blocking these areas.
Securing the Heater Feet
•
The heater has two plastic stands
or ‘feet’ that come with a set
of screws that you will need
to secure at the base of the
product. Locate the screws that
are positioned at the base of the
unit, approximately 5cm from
the far left and right sides of the
heating unit. Unscrew them, but
leave the centre screw in place.
•
•
Clip the plastic feet into the two
perforations, located at the base
of the unit.
Line up the screw holes in the
plastic stands with those in the
base of the heater. Re-attach the
screws to secure the plastic feet.
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
8
4/12/09 2:01 PM
1. Locate the three brackets at the
back of the heater. There are
two brackets at the left and right
hand bottom corners, and one
situated at the top of the heater
in the centre.
CAUTION: Do not
mount the heater
below curtains and/or
other flammable items.
2. As a general safety guide select
a suitable location to wall mount
the heater, approximately
CAUTION: If the heater
is intended to be
used in a bathroom,
the heater is to be
installed so that
switches and other
controls cannot be
touched by a person
in the bath or shower.
500mm from any furniture either
side of the unit and 500mm from
any furniture placed in front of
the heater. The heater must be
mounted horizontally as per Fig. 1.
3. When selecting a location, make
sure the base of the heater is at
least 500mm from the floor and
the top of the heater is at least
1.5m from the ceiling to ensure
there is adequate air flow into the
air inlet.
4. Measure out and mark the
screw locations. Once you
are confident that the screw
locations are correct, drill suitable
size holes.
5. Take care with inserting the
screws into the holes you have
made, and then mount the
heater onto the screws.
6. Once the heater is mounted on
to the wall, screw in the locking
screw (the shortest screw) to
prevent the heater from being
accidentally dislodged from the
mounting bracket.
7. Visually inspect the air inlet
and outlet to ensure no foreign
material is blocking these areas.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
9
4/12/09 2:01 PM
Operating Instructions
1. Plug the cord into a 230-240V
electrical outlet. Be sure the
plug fits tightly, as a loose fit
will cause overheating and
damage the plug. To avoid an
electrical circuit overload, it is
recommended that no other
appliances are plugged into the
same circuit with your heater
when you switch the unit on.
2. There are two ON/OFF switches
located at the top left hand side
of the rear of the heating unit, with
4 settings.
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the heater
in the event of overheating. Should
this heater stop working, turn off the
heater and inspect the air inlet and
outlet for blockages. Wait at least five
minutes for the protection system to
reset before attempting to restart
the heater.
If the heater fails to operate or the
safety device switches off again,
return the heater to your nearest
Kambrook Service Centre for
examination or repair.
- OFF
- Low (800W)
- Medium (1200W)
- High (2000W)
When the heater is not in
operation, both switches will be in
the OFF position.
3. To activate the LOW heat setting,
press the switch marked 800W
from OFF to ON.
4. To activate the MEDIUM heat,
setting, press the switch marked
1200W from OFF to ON.
5. To activate the HIGH heat setting,
press both the 800W & 1200W
switches from OFF to ON.
6. To turn the heater completely
off, return both of the OFF/ON
switches to the OFF position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd 10
4/12/09 2:01 PM
Care and Cleaning
Always turn off and then unplug the
heater before cleaning
Use only a clean, dry cloth to
clean the external surfaces of the
heater only.
If the heater has collected dust or
dirt inside the unit or around the
elements, have the unit cleaned by
a qualified service agent. Do not
operate the heater in this condition.
Do not attempt to open the case of
the heater at any time there are no
customer serviceable parts inside.
When not in use, pack the heater in
its original box for best protection and
store in a cool, clean and dry location.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd 11
4/12/09 2:01 PM
Kambrook 12 Month Replacement Warranty
In Australia, this Kambrook Replacement
purchase (or 3 months commercial use).
Warranty does not affect the mandatory
statutory rights implied under the Trade Practices
Act 1974 and other similar State and Territory
legislation relating to the appliance. It applies in
addition to the conditions and warranties implied
by that legislation.
The Kambrook Replacement Warranty does not
apply to any defect, deterioration, loss, injury or
damage occasioned by, or as a result of, misuse
or abuse, negligent handling or if the product
has been used other than in accordance with
the instructions. The Kambrook Replacement
Warranty excludes breakables such as glass and
ceramic items, consumable items and normal
wear and tear.
In New Zealand, this Kambrook Replacement
Warranty does not affect your mandatory
statutory rights implied under the Consumer
Guarantees Act 1993 in relation to the appliance.
It applies in addition to the conditions and
guarantees implied by that legislation.
This Kambrook Replacement Warranty is void if
there is evidence of the product being tampered
with by unauthorised persons.
This Kambrook Replacement Warranty is valid
only in the country of purchase, but other
statutory warranties may still apply.
If the product includes one or a number of
accessories only the defective accessory
or product will be replaced. Subject to your
statutory rights, in the event of Kambrook
choosing to replace the appliance, the
Kambrook Replacement Warranty will expire at
the original date, i.e. 12 months from the original
This Warranty card and the purchase receipt
for this product are to be retained as proof of
purchase and must be presented if making
a claim under the Kambrook Replacement
Warranty. Please note that under any applicable date of purchase.
statutory warranty you are not required to
In the event that you need some assistance
produce these documents, but may be required
to provide a proof of purchase.
with your Kambrook appliance, please contact
our Customer Service Department on 1300 139
798 (Australia) or 09 271 3980 (New Zealand).
Kambrook warrants the purchaser against
defects in workmanship and material for a period Alternatively, visit us on the website at
of 12 months domestic use from the date of
www.kambrook.com.au
Kambrook 12 Month Replacement Warranty
Your Purchase Record (Please Complete)
Attach a copy of the purchase receipt
here.
Date Of Purchase________________________________
Model Number __________________________________
Serial Number____________________________________
Purchased From _________________________________
(Please don’t return purchase record
until you are making a claim)
Kambrook - New Zealand
Private Bag 94411
Botany, Manukau
Auckland 2141
New Zealand
Customer Service Line/Spare Parts
0800 273 845 or 09 271 3980
Kambrook - Australia
Building 2, Port Air Industrial Estate
1A Hale Street
Botany NSW 2019
Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
Customer Service Fax 0800 288 513
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue 1/10
Download from Www.Somanuals.com. All Manuals Search And Download.
KPH200_IB_Issue1,10.indd
1
4/12/09 2:01 PM
|