CAPRESSO
Impressa S9
One Touch
Fully Automatic
Coffee & Espresso Center
with Clearyl Water Care System
Operating Instructions
and Warranty
Customer Service 1-800-220-5701
Impressa S9 One Touch
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice: This machine has a 3-prong grounded plug.
To reduce the risk of electrical shock, this plug will fit in an
outlet only one way. If the plug does not fit in the outlet,
contact a qualified electrician. DO NOT modify the plug in
any way.
JURA-CAPRESSO
Jura was founded in 1931 in Switzerland. Capresso was
founded in 1994 in the USA. Both companies have joined
forces in the US to bring you the finest Fully Automatic
Coffee Centers available anywhere. With innovative and
user-friendly features, high quality materials, clear instruc-
tions and superb customer service, we are sure you will
experience the best coffee, espresso, cappuccino or latte
you have ever had. We hope you will enjoy your new Fully
Automatic Coffee Center and will recommend it to your
friends. For more information about our products visit our
CAUTION
This appliance is for household use. Any servicing other than
cleaning and user maintenance should be performed by an
authorized service representative.
• Do not immerse base in water or try to disassemble.
• To reduce the risk of fire or electric shock, do not remove
the base. No user serviceable parts inside. Repair should
be done by authorized service personnel only.
• Check voltage to be sure that the voltage indicated on the
name plate agrees with your voltage.
Customer Service
1-800-220-5701
• Never use warm or hot water to fill the water container!
Use cold water only!
• Keep your hands and the cord away from hot parts of the
appliance during operation.
• Never clean with scouring powders or hard implements.
Mon-Thu 9AM – 9PM • Fri 9AM – 8PM • Sat 9AM – 5PM
Eastern Standard Time.
email: [email protected]
Jura-Capresso
81 Ruckman Road, Closter, NJ 07624
201-767-3999 • Fax: 201-767-9684
3.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 1
1. Height-Adjustable Dual Coffee Spout
2. Operating Display (Fig.2)
3. Removable Water Tank
4. Low Water Flotation Device (inside)
5. Clearyl Water Care Cartridge
(Not Installed)
10
11
12
13
14
15
15a
16
17
18
19
9
8
7
6
5
4
3
6. Lid for Water Tank
7. Holder for Clearyl Water Cartridge
8. Bean Aroma Protection Lid
9. Cover for Bean Container
10. Lid for Ground Coffee Funnel
11. Opening for Ground Coffee
12. Warming Plate
13. Auto Cappuccino System (Fig. 3)
14. Hot Water Spout
15. Steam Nozzle
15a. frothXpress system (Fig. 15 through 17a)
with thermal milk container attached
16. Used Coffee Container
17. Cup platform
18. Removable Drawer/Used Water Tray
19. Cover for Rotary Dial and
A La Carte Button (Fig. 3A)
2
1
FIG. 1b
FIG. 1a
a. Scoop
d
a
c
b. Cleaning tablets
c. Water indicator
d. Clearyl filter
Main Power Switch
b
4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Display
FIG. 2
Auto Cappuccino System
FIG. 3
FIG. 3A
FIG. 4
COFFEE
READY
A
B
N
O
3.1
3.2
3.5
3.3
3.4
E
P
3.6
3.7
C
D
F
Dual
Coffee
Spouts
Hot
Water
Spout
Q
G
Display Dialog System
3.1 Hot Water Portion symbol
N.
O.
P.
A.
B.
C.
D.
E.
F.
A La Carte Button
ON/OFF Button
Ground Coffee Button
Rotary Dial w/push button
3.2 Milk Portion symbol
3.3 Selector Dial with push button
3.4 Hot Water symbol
1-CUP Espresso Button
1-CUP Coffee Button
RINSE Button
Q.
Service Cover
(do not remove)
3.5 Milk symbol
2-CUP Espresso Button
2-CUP Coffee Button
3.6 Cappuccino button
3.7 Latte Macchiato button
G.
5.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 5
FIG. 6
FIG. 7
FIG. 8
FIG. 9
FIG. 10
FIG. 11
FIG. 12
FIG. 13
Extension rod
6.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 14a
FIG. 14b
FIG. 15
Black fitting
Transparent
fitting
Coffee
spout
Milk
hose
Stainless steel rod
Milk/ Steam
spout
FIG. 16
FIG. 17
FIG. 17a
Siphoning
with
flexible
hose
venting tip
chrome
face plate
Frothing range
Steam only
no siphoning
DIAL
Steaming range
7.
Download from Www.Somanuals.com. All Manuals Search And Download.
FIG. 19
FIG. 20
FIG. 21
FIG. 18
FIG. 22
FIG. 23
FIG. 24
FIG. 25
8.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
PAGE
8a. Turning the Machine Off / Rinsing............................. 16
Important Safeguards / Jura Capresso .....................
2
Drawings ....................................................................4-8
Important / Battery Back-up................................... 11
Product Warranty Registration................................... 11
Operating Instructions / Quick Reference Guide ...... 11
Welcome to the Impressa S9 One Touch.................. 11
9. Coffee Preparation................................................... 16
9a. Pre-warm Cups.......................................................... 16
9b. Brewing Coffee and Espresso................................ 16
9c. Overriding Strength and Cup Size During Brewing ..... 17
9d. The A La Carte Button............................................... 17
9e. Using Pre-Ground Coffee .......................................... 17
10. Auto Cappuccino System........................................ 18
10a. Preparing the Thermal Milk Container....................... 18
10b. The Froth XPress System .......................................... 18
1.
2.
3.
3a. Bean-to-cup, “Crema Coffee” and
Pressure Brewing....................................................... 12
3b. Different Coffee Drinks............................................... 12
3c. Coffee Facts............................................................... 12
4.
5.
6.
Please Don’t / Please Do ........................................ 12
Factory Settings / Options......................................... 13
Preparing the Machine for the First Time............. 14
10c. Preparing One-Touch Cappuccino,
Cafe Mocha and Latte............................................. 19
10d. Preparing One-Touch Latte Machiato.................... 19
10e. Preparing Hot Milk / Hot Chocolate ...................... 19
10f. Overriding the Cappuccino Settings ......................... 20
10g. Cappuccino Rinsing................................................... 20
10h. Using Hot Water......................................................... 20
11. Visual Programming of Beverage Portions......... 21
12. Water Care ................................................................. 21
6a. Filling the Water Tank................................................. 14
6b. Filling the Bean Container ......................................... 14
6c. Turning the Machine On for the First Time ............... 15
6d. Cup Illumination ......................................................... 15
7.
8.
Adjusting the Grinder................................................. 15
Daily Preparation........................................................ 15
9.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Continued
PAGE
PAGE
Care and Maintenance Messages ....................... 29
12a. Water Hardness Monitor......................................... 21
15.
12b. Changing the Water Hardness Monitor .................. 22
15.1 Manual Maintenance Cycles ................................... 30
15.2 Removing Stones etc. from the Burr Grinder ......... 31
15.3 General Cleaning Instructions ................................. 31
15.4 Emptying the System before Transport................... 31
15.5 Cleaning the frothXpress ......................................... 31
13.
Clearyl Water Filter Cartridge.................................. 22
13a. Installing and Activating the Clearyl
Water Cartridge ..................................................... 23
13b. Automatic Clearyl Replacement.............................. 23
13c. Manual Clearyl Replacement .................................. 24
13d. Do Not Let the Clearyl Filter Dry Out!..................... 24
16.
Automatic Cleaning Cycles ..................................... 32
16.1 Cleaning with Special Tablet ................................ 32
14.
Programming ......................................................... 24
16.2 Manual Tablet Cleaning ........................................... 33
14.1 Re-Programming Beverage Buttons ................... 24
14.2 Restoring Factory Settings for Beverage Buttons .... 26
14.3 Economy Modes ..................................................... 26
14.4 Actual Time and Weekday ...................................... 27
14.5 Auto-On and Auto-Off Times................................... 27
14.6 Auto-Off.................................................................... 28
14.7 Rinse Settings.......................................................... 28
14.8 Information............................................................... 29
14.9 Display Settings....................................................... 29
14.10 Languages................................................................ 29
17.
Decalcifying.............................................................. 33
17.1 Decalcifying Procedure............................................ 34
17.2 Manual Decalcifying................................................. 34
18.
19.
20.
21.
22.
Tips For Better Coffee ............................................. 35
Error Messages / Troubleshooting........................... 35
Supplies................................................................... 36
Limited Two-Year Warranty...................................... 37
Free Repair Service / Extra Repair Coverage......... 38
10.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT / BATTERY BACK-UP
The Impressa S9 One Touch has an internal battery back-up for
without moving your cup, brews one or two cups of crema
coffee or espressos at a time, produces unlimited amounts of
the clock functions. After plugging the S9 OT in for the first time, hot frothed and hot steamed milk and delivers up to 15 oz. hot
turn the Main Power Switch in the back of the machine on (Fig. 1b;
the red indicator light in the ON/OFF button (Fig. 2,B) will illumi-
nate). Leave the main power switch on for the first 24 hours to
insure that the internal battery back-up is fully charged.
water – all with a push of a button.
With its two independent stainless steel Thermoblock heating
systems it switches from brewing coffee to frothing milk without
any up- or down-time. The two-step pressure brewing system -
well known in commercial applications - was adapted and
refined by Jura coffee specialists and is the trademark of each
Jura-Capresso coffee center. This two step brewing system
ensures optimal coffee extraction and will finish every cup with a
rich layer of "crema" - proof for perfectly pressure brewed cof-
fee. The adjustable, commercial conical burr grinder grinds
beans to the desired fineness (6 settings). Use pre-ground coffee
with the separate filler funnel. The second Thermoblock gener-
ates unlimited steam instantly. Program a specific amount of
frothed/steamed milk and the S9 OT will always deliver your pre-
ferred cup size. A separate hot water spout prepares a cup of tea
or any other hot beverage in seconds. With four pre-set coffee
buttons, four pre-set milk beverage buttons, a special A La Carte
button and the easy-to-use Rotary Dial you can prepare thousands
of different coffee beverages with the push of a button. Override
or re-program your favorite coffee drinks. Select from different
maintenance set-ups. The S9 OT automatically reminds you
when to refill water, clean, change filter or decalcify. The
"Information" section lets you know how many coffees you pre-
pared with the different coffee buttons. The beautiful housing,
cup illumination and informative LED display make the S9 OT
the most versatile Super Automatic Coffee Center available today.
Enjoy your Impressa S9 One Touch!
1. PRODUCT WARRANTY REGISTRATION
Remove the Product Registration from the Welcome Pack, fill it
out and mail or fax it to us within two weeks or register your
Important: This registration is part of your warranty (chapter 21).
If your retailer sent the product registration to Jura-Capresso when
you purchased the machine, it is not necessary to register again.
2. OPERATING INSTRUCTIONS
QUICK REFERENCE GUIDE / DVD
Thank you for choosing this Jura-Capresso product.
Important: Do not try to set-up the Impressa S9 One Touch
without following the set-up steps in chapter 6 - 8. Or use the
Quick Reference Guide.
• Take time to study this instruction manual. It covers many
features of the S9 OT and provides helpful hints and
will enhance your enjoyment with coffee beverages.
• We highly recommend viewing the enclosed DVD.
3. WELCOME TO THE IMPRESSA S9 One Touch
This fully automatic coffee/espresso/cappuccino center is
completely programmable and extremely user friendly. The S9
OT prepares a cup of cappuccino or latte at a push of a button
11.
Download from Www.Somanuals.com. All Manuals Search And Download.
3a. BEAN-TO-CUP / “CREMA COFFEE" /
Experiment with the size of your milk based drinks. For stronger
coffee taste add more coffee, for more milk taste add more
frothed/steamed milk.
HIGH PRESSURE BREWING
According to the majority of coffee experts, grinding the beans
just before brewing, tamping and brewing under high pressure is
the ideal extracting process for maximum flavor and aroma. Your
S9 OT automatic coffee center will always produce espresso and
coffee with a thick, foamy layer called "crema." The crema traps
the fine aromatics and the light gaseous flavors that register on
the palate. The high pressure and the short brewing time
prevent the extraction of bitter oils and release less caffeine than
any other brewing method.You will always make the absolute
freshest and most aromatic cup of coffee. This is the reason why
many European restaurants and hotels serve only fresh pres-
sured brewed coffee. Experiment with your S9 OT and prepare
the best and most enjoyable cup of coffee!
3c. COFFEE FACTS
• Caffeine is tasteless. A "strong" coffee or espresso is mostly
the result of the amount of coffee in relation to the amount of
water. The longer a bean is roasted, the less caffeine it has.
The shorter the brewing time the less caffeine in your cup.
• Arabica and Robusta are two genetically different kinds of
beans. "Arabica" beans have more flavor and a little less caffeine
than "Robusta" beans which are mostly used in lower priced
coffees and instant coffees.
• Espresso is not a bean! It's the way the coffee is roasted and
prepared. Typical US espresso roasts result in darker beans with
an oily surface. European espresso roasts are medium brown
with no or very little oils on the surface.
3b. DIFFERENT COFFEE DRINKS
Here are some guidelines for the most popular coffee drinks:
• Ristretto: 1/2 to 1 oz. of coffee. Sweeten to taste.
• Espresso: 1 to 2 oz. coffee. Sweeten to taste.
• Double Shot: 3 to 4 oz. of coffee. Sweeten to taste.
• Crema Coffee: 5 to 8 oz. of coffee.
• Cappuccino: 3 to 4 oz. of hot frothed milk plus espresso.
• Latte: 3 to 5 oz. steamed milk with little or no froth plus espresso.
• Latte Macchiato: 5 to 6 oz. of frothed/steamed milk produced
with pause*, plus one or two shots of espresso. *The pause
separates the milk froth and the milk and allows the espresso
to settle “in between” (chapter 10d).
All Display Messages Are Shown in RED
4. PLEASE, DON’T... (or you void your warranty protection):
• Never pull out the drawer during the brewing process. Only
pull the drawer when the display instructs you or when the
display shows COFFEE READY.
• Never fill instant coffee into the bean container or ground coffee
funnel; it will damage the brewing chamber.
• Never fill sugar coated coffee beans into the bean container.
• Never fill frozen beans into the bean container. Do not keep
beans in the freezer. Store them in a dark, airtight container.
• Never fill anything other than coffee beans into the bean
container (no chocolate, rice, nuts, spices, etc.).
• Café Mocha: Use chocolate milk then proceed as in making
cappuccino or latte.
12.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Never fill anything but fresh, cold clean water into the water
container, except when decalcifying (chapter 17.1).
• Never use mineral or carbonated water. You can use tap
water, bottled water, spring water, distilled water and reverse
osmosis water.
Coffee volume:
• All 1-cup buttons can be programmed to brew between
0.5 and 8 oz. of coffee.
• The Hot Water Portion can be programmed to dispense up to
15 oz. of hot water.
• Never repair or open the machine yourself. All repairs should
be performed only by an authorized service center.
• Do not place the machine on a surface which is sensitive to
hot or cold water and steam. Never place the machine on an
uneven surface.
• All 2-cup buttons can be programmed to brew between
0.5 and 8 oz. per cup, total of 16 oz. max.
Tip: if you use a 12 oz. mug and program one of the 2-cup
buttons to 5 oz. the S9 OT will brew a total of 10 oz. of coffee
into your mug.
Coffee strength (AROMA):
PLEASE, DO...
• All 1-cup buttons can be set to five different coffee strengths:
XMILD, MILD, NORMAL, STRONG, XSTRONG.
In XMILD the conical burrs grind for approx. 5 seconds, in
XSTRONG, the grinding takes about 9 seconds.
• When using the 2-cup buttons, the S9 OT will always grind in
XSTRONG.
• Fill water tank daily with fresh, cold water.
• Before filling the bean container, remove any foreign particles
(small stones) from coffee beans.
• Let frozen beans thaw for 3 to 4 hours before pouring them
into the bean container.
Important: If you pull out the drawer at any time you must empty Please note: The display indicates the five strength settings with
the used coffee container and the drawer. If you do not empty the
container, used coffee will overflow inside the machine and can
cause serious damage to the internal mechanism.
graphics showing from one to five coffee beans.
Temperature:
• All coffee buttons can be set to NORMAL or HIGH.
• The Hot Water function can be set to LOW, NORMAL, XHIGH
(XHIGH is used for pre-warming cups and for specialty teas).
Steaming for milk frothing:
• The cappuccino and latte macchiato buttons and the milk
portion can be set to produce steam from 3 to 120 seconds.
Latte Macchiato Pause:
5. FACTORY SETTINGS / OPTIONS
The IMPRESSA S9 One Touch can be set up in many different
ways. Beverages, on/off settings, temperature, rinse cycles,
water treatment, energy savings modes and display information
can be programmed to your personal preferences.
Beverage buttons can be customized with regards to volume
(cup size), coffee strength (AROMA), temperature, duration of
milk steaming/frothing.
• The pause between milk frothing and coffee brewing can be
set from 0 to 60 seconds.
13.
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Settings for Beverage Buttons:
• All coffee buttons are set to temperature HIGH.
• The hot water function is set to XHIGH.
• 1-CUP Espresso button (Fig. 2,C) 2 oz./ STRONG.
• 2-CUP Espresso button (Fig. 2,F) 2 oz. per cup / XSTRONG.
• 1-CUP Coffee button (Fig. 2,D) 5 oz./ STRONG.
• 2-CUP Coffee button (Fig. 2,G) 5 oz. per cup / XSTRONG.
• A La Carte button (Fig. 3A,N) 7 oz.
• DO NOT install the Clearyl water filter now (chapter 13a).
• Make sure the machine sits on an even, flat surface and the
drawer and used coffee container are inserted (Fig. 1).
• Plug-in machine.
6a. FILLING THE WATER TANK
Please note: Only use fresh, cold water. Never fill water tank
with carbonated water, milk or any other liquid.
• Remove the water tank, rinse and fill with fresh, cold water.
• Replace water tank and make sure that it engages securely.
• Cappuccino; one-touch button (Fig. 3.6) 14 seconds milk, 0
seconds pause, 2 oz. coffee / NORMAL.
• Latte Macchiato; one-touch button (Fig. 3.7) 14 seconds milk,
15 seconds pause, 2 oz. coffee / STRONG.
• Milk portion; Selector Dial (Fig. 3.5) 14 seconds milk,
6b. FILLING THE BEAN CONTAINER
Please note: To insure that the conical burr grinder will work for
a long time, do not use it with any kind of coated or flavored
beans (all coating and flavors contain sugar or sugar substances).
Such coating can damage the burrs. Using such beans voids the
warranty. Have your coffee store grind the sugar coated beans
and use as described in chapter 9e.
Flavored Coffee: If you like flavored coffees we recommend
adding flavors to your coffee after brewing. This way you can
use your regular coffee beans in the bean container. Adding the
flavors after brewing lets you control the flavor intensity much
better than with pre-flavored coffee. Your local coffee store
typically carries a variety of liquid flavors.
• Water Portion; Selector Dial, 5 oz.; XHIGH.
Other Factory Settings:
• 5-hour auto shut-off.
• Water hardness setting: 10ºdH.
• Filter: FILTER NO (Clearyl Water Care Cartridge: not installed)
• Language: English.
• Display: AM/PM and OZ.
• Economy Mode (energy saving): Off
• Time / Weekday: --.-- (not set)
• Automatic On and Off times: not set
• Cappuccino Rinsing: set to NOW; display shows
CAPPUCCINO RINSING immediately after frothing milk.
• Open the Cover Lid (Fig. 5).
• Remove the Aroma Protection Lid (Fig. 6).
• Make sure the bean container is empty and clean. Fill beans
into the bean container (Fig. 7).
6. PREPARING THE MACHINE FOR THE FIRST TIME
• Make sure all accessories, literature and any other items are
removed from the bean container and the water tank.
Frozen Beans: Thaw 3 to 4 hours before adding to bean
container. This prevents moisture from seeping into the grinder.
14.
Download from Www.Somanuals.com. All Manuals Search And Download.
Oily Beans: Beans with an oily surface tend to stick together.
This may prevent a continuous flow of beans from the bean
container into the burrs. As a result the grinder does not grind
enough coffee and you might get weak or no coffee at all.
Stir the beans in the bean container just before grinding.
6d. CUP ILLUMINATION
The cup illumination adds a dramatic touch to brewing coffee.
Providing the machine is plugged in, you can activate the cup
illumination for 3 minutes by pressing any button.
Alternatively, you can also pour the beans into an open bowl and 7. ADJUSTING THE GRINDER
let them sit for about 5 hours. The oils will evaporate (this will
not change the taste of your coffee). Then fill the beans into the
bean grinder. Now beans will feed into the burrs more easily.
IMPORTANT: The grinding grade can only be adjusted while
the grinder is actually grinding.
Adjust the grinder to the roast of your coffee.
• Light roast: use a finer adjustment (smaller dots).
• Dark roast: use a coarser adjustment (larger dots).
• Open the cover of the bean container (Fig. 5).
6c. TURNING THE MACHINE ON FOR THE FIRST TIME
• Make sure bean container and water tank are filled.
• Press the Main Power Switch in the back of the machine (Fig. 1b) • To adjust fineness, turn the grinding wheel during grinding to
The On/Off button illuminates (Fig. 2.B).
the desired position (Fig. 9).
• Push the On/Off button. The display shows FILL SYSTEM /
PRESS RINSE and the Rinse button (Fig. 2.E) illuminates.
• Place containers underneath the Auto Cappuccino System
and the Hot Water Spout (Fig. 4) and push the Rinse button
(Fig. 2.E). SYSTEM FILLING. The machine will dispense a
small amount of water. HEATING UP / PRESS RINSE.
• Place cup underneath the dual coffee spout (Fig. 4) and press
the Rinse button (Fig. 2.E). MACHINE RINSING. The machine
will dispense a small amount of water. COFFEE READY.
Please note: You can only make coffee when the display reads
COFFEE READY.
ATTENTION: Oily beans tend to stick together. Stir beans just
before grinding to ensure a proper flow of beans into the burrs.
Please note: If coffee does not flow through the Dual Coffee
Spouts in a constant stream, turn the wheel to a coarser setting.
8. DAILY PREPARATION
Fill the water container every morning with fresh, cold water. This
will enhance the taste of your coffee.
• Make sure the Main Power Switch is on (Fig. 1b). In this case
the On/Off button is illuminated.
• Push the On/Off button. The display shows WELCOME TO
JURA and then HEATING UP. After approx. 2 minutes the
display shows PRESS RINSE.
• Push the Rinse Button* (Fig. 2,E). Hot water will warm up all
internal parts and pump through the coffee spouts MACHINE
• Place a cup under the coffee spout and push one of the coffee
buttons. The machine will grind and brew coffee. If the display
shows FILL BEANS push one of the coffee buttons again.
• Discard the first two cups of coffee.
You are now ready to brew coffee.
15.
Download from Www.Somanuals.com. All Manuals Search And Download.
RINSING. The water will be caught in the drawer underneath.
The rinse cycle stops by itself and the display reads: COFFEE
READY. You are now ready to make coffee.
*Note: S9 OT can be programmed to automatically start the
rinsing cycle after HEATING UP is displayed (chapter 14.7).
9. COFFEE PREPARATION
9a. PRE-WARM CUPS
In the morning pre-warm your cups with hot water through the
Hot Water Spout. Cold cups reduce the coffee temperature by
5ºF to 10ºF.
Place a cup under the Hot Water Spout, turn the Selector Dial
(Fig. 3.3) until the display shows HOT WATER and push the
Selector Dial. The display shows TEMP. XHIGH and water will
flow into your cup. Push the Selector Dial again to stop and
discard the water. COFFEE READY.
8a. TURNING THE MACHINE OFF / RINSING
Before turning off the S9 OT, place containers under the Dual
Coffee Spouts and Auto Cappuccino System (Fig. 4).
When the S9 OT is turned off or turns itself off it will prompt for
short cleaning cycles as follows:
9b. BREWING COFFEE AND ESPRESSO
Only the Dual Coffee spouts were used: The S9 OT displays
MACHINE RINSING. For a few seconds hot water will be
dispensed through the Dual Coffee Spouts and through the
coffee spout of the Cappuccino section. The machine and the
display turn off.
The Auto Cappuccino Spouts and the Dual Coffee Spouts
were used: The S9 OT first displays CLEAN CAPPUCCINO
and the Rinse button illuminates. If the Rinse button is not
pushed within the next ten seconds, the display shows SPOUT
RIGHT / PRESS RINSE. Press the Rinse button. The S9 OT will
dispense some hot water through the coffee spout of the
Cappuccino section. It will then push some hot water through
the Dual Coffee Spouts and turn off.
The machine has four pre-set coffee buttons, 1 ESPRESSO,
2 ESPRESSI, 1 COFFEE, 2 COFFEES (Fig. 2).
All buttons are pre-set for coffee strength, coffee volume and
temperature (chapter 5).
• Place one or two cups underneath the Dual Coffee Spouts
and push the desired button. The machine will grind, tamp
and then brew the coffee. It uses a 2-step brewing process
(pre-brew phase), pauses for a few seconds, and then starts
the brewing process. The display will show the name of the
button you pushed, e.g. 1 ESPRESSO and the selected coffee
strength indicated by a bean graphic, e.g. 4 beans = strong.
Please note: when pushing any of the two-cup buttons, the
coffee strength is not displayed.
Please note: When the S9 OT turns off you may hear a slight
hissing noise.
Important: After the brewing stops the machine will discard the
used coffee grounds. Please do not try to pull out the drawer
(Fig.1,18) during this operation. It can seriously damage the
machine.There is no need to pull out the drawer until the display
shows the message EMPTY TRAY or EMPTY GROUNDS.
16.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note: You can always stop the brewing process by
before brewing. COFFEE READY.
pressing any of the coffee buttons.
• Push the A LA CARTE button (Fig. 3A.N). The display shows
A LA CARTE and the strengths indicated by the bean graphic
e.g. 2 beans (mild).
• Turn the Rotary Dial to choose any of five strength settings:
XMILD, MILD, NORMAL, STRONG, XSTRONG, indicated by
1 to 5 beans in the bean graphic.
• Then push the Rotary Dial. The machine starts grinding. Now
dial the coffee volume.
Please note: If you push the A LA CARTE button and do not
push the Rotary Dial within a few seconds, the display will
revert to COFFEE READY.
9c. OVERRIDING STRENGTH AND CUP SIZE DURING
BREWING
During brewing you can override the strength of the two one-
cup buttons (Fig. 2, C, D) and the cup size of all four coffee
buttons. When using the two-cup buttons the S9 OT automati-
cally selects the maximum strength. Overriding will not change
the factory setting (chapter 5).
Example:
• Open the cover for the Rotary Dial (Fig. 1.19).
• Push the 1-Cup Coffee Button (Fig. 2D).
• During grinding turn the Rotary Dial to change the strength to
e.g. XSTRONG (5 bean graphic). The display shows the
selected strength.
• When the coffee starts brewing, turn Rotary Dial until the display
shows, e.g. 7.0 OZ. The S9 OT will brew 7.0 oz of coffee.
If you use the same coffee button again and do not use the
Rotary Dial, the S9 OT will brew a cup according to the
programmed settings for this button.
Please note: When using one of the 2-Cup buttons you can
only change the cup size. The display shows the amount per
cup, e.g. 6.0 OZ; the S9 OT will brew a total of 12 ounces.
For re-programming see chapter 11 (cup sizes) and chapter 14.1
for cup sizes, temperature and strength.
9e. USING PRE-GROUND COFFEE
You can also use pre-ground coffee, bypassing the grinder. This
is convenient if someone requests decaf coffee or a decaf
cappuccino or flavored coffee.
Please note: Never fill the funnel with instant coffee. Do not fill
the funnel with more than two scoops. The funnel is not a
storage container. If coffee is ground too fine the brewing
process may be stopped.
COFFEE READY
• Open cover (Fig. 1,19) and push the Ground Coffee button
(Fig. 3A,O). FILL PRE-GROUND / COFFEE READY.
• Fill 1 or 2 level measuring scoops of ground coffee into the
opening for ground coffee (Fig. 1,11) and close the lid.
• Now push one of the four coffee buttons to brew your coffee
e.g. 1 COFFEE. The pre-ground coffee is tamped and brewed.
ENJOY, then COFFEE READY.
9d. THE A LA CARTE BUTTON
The S9OT has a fifth coffee button (Fig. 3A,N). With this button
you can change the coffee volume and the coffee strength just
17.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please note: If the Ground Coffee button (Fig. 3A,O) is
pressed by mistake just press one of the coffee buttons, NOT
ENOUGH PRE-GROUND. The machine will automatically stop
and return to COFFEE READY.
Please note: After use of sugar coated or flavored coffee
through the pre-ground coffee funnel you may experience some
flavor transfer when switching back to your regular coffee.
• Rinse the milk container with fresh water before first use and
fill with fresh cold milk. Close the lid.
• Insert one end of the short flexible hose into the lid opening.
• Remove the red cap from the side of the frothXpress and
insert the other end of the short flexible hose (Fig. 15).
You are ready to steam/froth milk.
Storing the milk container: always remove the outside flexible
hose and open the lid before storing the milk container in the
refrigerator.
10. AUTO CAPPUCCINO SYSTEM
The S9 OT features the Auto Cappuccino System with two spouts
located behind each other (Fig. 15) The front spout produces
steam (steam nozzle). The rear spout produces high pressure
brewed coffee. Attached to the steam nozzle is the removable
frothXpress system. It siphons, steams and froths milk.
The S9 OT Cappuccino System prepares a variety of milk based
drinks without ever moving the cup: Cappuccino, Latte, Latte
Macchiato, Café Mocha, Hot Milk, Hot Chocolate.
Important: The milk container is not dish washer safe. Do not
immerse the milk container in any liquid.
Using the long flexible hose: To siphon milk directly from a milk
carton use the long flexible hose. Insert one of the black con-
necting pieces in the straight-cut end of the hose and insert into
the frothXpress. Insert the other end with the V-cut into the milk
container (Fig. 17).
10b. THE FROTHXPRESS SYSTEM
This system produces unlimited amounts of hot steamed or
frothed milk right into your cup.
10a. PREPARING THE THERMAL MILK CONTAINER
The S9 OT comes with a 20 oz. double walled vacuum stainless
steel container. This custom-made milk container can keep cold
milk cold for up to eight hours. There is no need to worry about
the milk getting warm during the day.
The milk container comes complete with: • lid and attached
stainless steel hose • two short flexible hoses • one long flexible
hose • spare black and transparent fittings (Fig. 14a, 14b).
The two short hoses have a connecting piece on each end.
• Unscrew the milk container lid. A stainless steel hose is
attached to the inside of the container. A small transparent
fitting holds the hose in place (a spare fitting is included).
Important: This system siphons milk and mixes it inside the
frothXpress with hot steam. It is necessary that all parts are
connected tightly, otherwise the siphoning process will not work.
Frothing Position: The dial points to the upper part of the face
(12 to 2 o’clock). This section is used for Cappuccino and Latte
Macchiato. In the 12 o’clock position the frothXpress creates the
most milk froth. Turning the dial towards the 2 o’clock position
increases the milk temperature (Fig. 16).
Steaming Position: The dial points to the lower part of the face
18.
Download from Www.Somanuals.com. All Manuals Search And Download.
(6 to 4 o’clock). Milk will be steamed, not frothed. Turning the
dial towards the 4 o’clock position increases milk temperature.
Steam Only Position: When the dial points to the steam symbol
(3 o'clock), the siphoning is blocked. Only steam will pass
through the frotherXpress.
Please note: You can always stop the beverage preparation by
pushing any of the beverage buttons.
10d. PREPARING ONE-TOUCH LATTE MACCHIATO
This beverage is very popular in Europe. It is normally served in
glasses, approx. 4 to 5 inches tall and 2 inches in diameter.
10c. PREPARING ONE-TOUCH CAPPUCCINO, CAFÉ MOCHA COFFEE READY.
AND LATTE
The frothXpress dial points to the 12 to 2 o’clock position.
COFFEE READY.
The frothXpress dial points to area between 12 and 2 o’clock
The milk container is connected.
• Place your latte macchiato glass underneath the Cappuccino
system and push the Latte Macchiato button (Fig. 3.7). The S9
OT starts grinding, the display shows LATTE MAC. and the
coffee strength. It then siphons, heats and froths milk for 14
seconds and pauses. The display shows PAUSE (factory
setting is 15 seconds). During this time the milk separates
from the milk froth. After the pause 2 oz. of high-pressure
brewed coffee are automatically added. LATTE MAC. Then
ENJOY. The coffee settles between the froth and the milk
giving the beverage the typical multi-layered, Latte Macchiato
look. COFFEE READY.
• Place your cappuccino cup underneath the Cappuccino
system and push the cappuccino button (Fig. 3.6). The S9 OT
starts grinding, the display shows CAPPUCCINO and the
coffee strength (bean graphic). It then siphons, heats and
froths milk for 14 seconds and adds 2 oz. of high-pressure
brewed coffee (Factory Settings, chapter 5). The display
shows ENJOY then COFFEE READY.
Tip: If you use a glass cup you can see how much froth is
created and how the coffee sits beneath the layer of milk froth.
Slightly stir to distribute the coffee evenly into the hot milk.
10e. PREPARING HOT MILK / HOT CHOCOLATE
The Cappuccino System can produce hot milk or hot chocolate
without brewing coffee.
CAFÉ MOCHA: use chocolate milk or add chocolate syrup to
your cold milk and stir then proceed as explained before.
COFFEE READY.
LATTE: turn the frothXpress dial between the 4 and 6 o’clock
position and repeat above steps. Milk is steamed without froth.
Please note: You can always add an additional shot of espresso
by placing your cup under the Dual Coffee Spouts (Fig. 4) and
pushing the 1-Cup Espresso button. You can also add additional
hot milk (chapter 10e).
• Connect the milk container to the frothXpress system or use
the long flexible hose inserted into any milk carton.
• Place your cup underneath the Cappuccino system.
• Turn the Selector Dial (Fig. 3.3) until the display shows MILK
or MILK PORTION ("MILK" siphons milk until you stop the
action by pushing the Selector Dial button again.
19.
Download from Www.Somanuals.com. All Manuals Search And Download.
"MILK PORTION" siphons milk for a programmed time and
stops automatically).
• Push the button inside the Selector Dial. The display shows
MILK or MILK PORTION. During this time hot steamed /
frothed milk is created and delivered into your cup.
COFFEE READY.
COFFEE READY / RINSE CAPPUCCINO and the Rinse button
illuminates. You can still continue making any beverages. We
recommend to perform the cappuccino rinsing since it takes
only a few seconds and makes sure that your frothXpress is free
of any milk.
• Turn the frothXpress dial to the 3 o’clock position (Fig. 16) and
place a cup underneath the cappuccino system.
• Push the Rinse button. The display shows CAPPU. RINSING.
Hot water is pushed through the frothXpress for a few seconds.
COFFEE READY.
10f. OVERRIDING THE CAPPUCCINO SETTINGS
As with the coffee buttons you can override the pre-programmed
volumes of the milk beverage buttons.
Example: The factory setting for the Cappuccino button is normal
strength (3 beans graphic), 14 seconds of milk frothing and 2 oz.
of coffee. Prepare a one-time special cappuccino, extra strong
(5 beans graphic), more milk froth (20 seconds) and 3 oz. of coffee.
COFFEE READY
• Turn the frothXpress dial back to your preferred position.
IMPORTANT: If you do not use the Cappuccino Rinsing cycle,
milk droplets might harden inside the frothXpress, resulting in
insufficient frothing performance.
• Place your cappuccino cup under the Cappuccino system
and open the cover for the Rotary Dial (Fig. 1.19).
• Push the Cappuccino Button (Fig. 3.6). During grinding turn
the Rotary Dial to change the strength until the display shows
the 5 bean-graphic.
10h. USING HOT WATER
The hot water function lets you pre-warm cups, brew tea, make
a quick cup of soup, or add hot water to your coffee or espresso
to create a milder flavor.
• When the frothing starts turn the rotary dial until the display
shows 20 SEC.
• When the coffee brewing starts turn the Rotary Dial until the
• Place a cup under the hot water spout (Fig. 4).
• Turn the Selector Dial (Fig. 3.3) until the display shows HOT
WATER or HOT WATER PORTION (HOT WATER PORTION
delivers a pre-programmed amount of hot water and then
stops automatically. HOT WATER delivers hot water until you
stop the action by pushing the Selector Dial button again).
• Push the button inside the Selector Dial. The display shows
the pre-set temperature e.g. TEMPERAT. X HIGH and then
HOT WATER or HOT WATER PORTION.
display shows 3.0 OZ.
10g. CAPPUCCINO RINSING
In only a few seconds this rinsing program removes milk droplets
inside the frothXpress.
After preparing a beverage with milk (Cappuccino Button, Latte
Macchiato Button, Milk, Milk Portion) the S9 OT display shows
COFFEE READY.
20.
Download from Www.Somanuals.com. All Manuals Search And Download.
The temperature for this function can be set to LOW, NORMAL
and XHIGH (chapter 14.1; example 3)
The next time you push the Cappuccino button, the S9 OT will
produce that amount of milk and coffee.
You can override the WATER PORTION during the hot water
release with the Rotary Dial.
12. WATER CARE
You can re-program the hot water portion (chapter 14.1).
The S9 OT works with: • tap water • bottled water • distilled
water. We recommend using tap water or bottled water. Distilled
water has no minerals and does not improve the taste of coffee.
Water that is heated inside the machine leads to calcium deposits.
Tap water has a varying degree of water hardness (chapter 12a).
Most bottled water has a low level of water hardness.
IMPORTANT: do not use carbonated water or any other liquid in
the water tank.
You have the following options to take care of the water.
• Decalcifying System (chapter 17.1).
• Clearyl Water Filter Cartridge (chapter 13a).
The machine is factory pre-set to automatically remind
you to decalcify.
11. VISUAL PROGRAMMING OF BEVERAGE PORTIONS
Chapters 14 and 14.1 explain how to re-program all parameters
(volume, strength, temperature) for the beverage buttons.
Re-programming the cup size for coffee and milk can also be
done during beverage preparation as follows:
• Push and hold the beverage button you want to re-program
until display shows ENOUGH COFFEE? or ENOUGH MILK?
This way you can make sure your (cappuccino) cup is
completely filled with milk and coffee.
Example:
Visually re-programming the Cappuccino button (Fig 3.6).
COFFEE READY.
• Prepare the Cappuccino Systems (milk container etc) to make
a cappuccino and place your cappuccino cup under the
frothXpress.
• Push and hold the Cappuccino button until display shows
ENOUGH MILK?
12a. WATER HARDNESS MONITOR
Your S9 OT is set to a water hardness of 10ºdH and will auto-
matically indicate when it is time to perform a decalcifying cycle.
You can change the water hardness setting from 1º to 30ºdH. If
you are not sure about the hardness of your water, ask your local
• When the desired amount of milk and milk froth is in your cup, water company for the "Water Hardness in Grains." The machine
push the Cappuccino button again. The display now shows
ENOUGH COFFEE?
• When enough coffee has been added to your frothed milk
push the Cappuccino button again. CONFIRMED ꢀ, then
ENJOY, then COFFEE READY.
displays the water hardness in the German hardness scale which
is a bit different from the American "Grain" scale (see chart
below). You can also use the water hardness indicator strip
("Aquadur" in Welcome Pack) to determine the water hardness:
• Insert the strip for one second into the water you want to
use. Shake off any access water and wait for one minute.
21.
Download from Www.Somanuals.com. All Manuals Search And Download.
One or more sections of the indicator strip will turn reddish.
• Change the water hardness setting according to the table
below.
• Push the Rotary Dial to enter the program.
• Turn the Rotary Dial until the display shows 20ºdH.
• Push the Rotary Dial to confirm the setting. CONFIRMED ꢀ
and then HARDNESS 20ºdH.
• Turn the Rotary Dial until the display shows EXIT.
• Push the Rotary Dial COFFEE READY.
Display Equivalent Indicator Strip
German American number of
Level
Display
Degree Grains
"reddish" fields
The machine will automatically remind you when it is time to
decalcify (chapter 17.1).
Please note: You can set the hardness monitor to INACTIVE.
In this case you must use distilled water. In this setting the
S9 OT will not remind you to decalcify the machine.
Not Active*
1. extremely soft water
2. soft water
3. medium water
4. hard water
5. very hard water
6. extremely hard water
INACTIVE
—
1-4
5-9
—
1-5
6-11
—
None
1 to 2
10-14 13-18 2 to 3
15-19 19-24 3 to 4
20-24 25-30 4 to 5
25-30 32-38 All 5
13. CLEARYL WATER FILTER CARTRIDGE
The machine comes with one Clearyl Water Filter Cartridge. The
Clearyl cartridge
• Reduces the water hardness up to 75%.
*Not Active: You can only use this setting for distilled water.
Level 5 and Level 6: If the tap water falls into these two cate-
gories, decalcifying will be frequent. In this case bottled water is
recommended. Most bottled water has a low calcium level.
Please note: If your water has a high calcium content (level 5 or 6)
and you use the Clearyl Filter Cartridge we recommend to decalcify
the machine once or twice a year (chapter 17 and 17.1).
• Removes (if present) up to 85% chlorine, up to 90% lead, up
to 95% copper and up to 67% aluminum.
• Cleans the water through an upward current principle (Fig. 10)
just before the brewing cycle starts, ensuring freshly filtered
water every time you make coffee.
• Lasts for 75 liters (~2,500 oz.) of water or up to two months.
• Eliminates decalcifying except when using very hard water
(25 grains or higher), see chapter 12. In this case we recom-
mended to decalcify the machine once or twice a year.
• To reorder cartridges, see chapter 20.
Please note: If you use Spring or Bottled Water with low calcium
levels you can set the hardness to 3ºdH, "extremely soft water".
12b. CHANGING THE WATER HARDNESS MONITOR
COFFEE READY
Example: change the hardness setting from 10ºdH to 20ºdH
• Push the Rotary Dial until display shows MAINTENANCE.
• Turn Rotary Dial until the display shows HARDNESS 10º DH.
22.
Download from Www.Somanuals.com. All Manuals Search And Download.
13a. INSTALLING & ACTIVATING THE CLEARYL WATER
CARTRIDGE
Installing:
and out through the frothXpress system. Initially, the water may
have a slight discoloration. The program will stop automatically.
The display shows COFFEE READY.
Important: Never install the cartridge before or during
"Preparing Machine For The First Time" (chapter 6).
6. Turn the frothXpress dial back to your preferred setting.
Please note: As long as the filter is activated, the water
• Remove cartridge from its bag and rinse cartridge under water. hardness setting is automatically turned off.
• Add the extension rod to the cartridge (Fig. 11).
• Remove the water tank, make sure it is empty.
• Pull up the cartridge holder and insert the cartridge with its
tapered end down into the water container (Fig. 12, Fig. 13).
Make sure it fits securely inside the fins. Push down gently
(Fig. 13).
• Close the cartridge holder. Make sure the holder snaps into
place.
• Fill the water tank with fresh cold water and replace.
13b. AUTOMATIC CLEARYL REPLACEMENT
The filter is monitored automatically. After approx. 75 liters of
water (~2,500 oz.) the display shows COFFEE READY /
CHANGE FILTER. The Rinse Button will light up.
Important: Once the filter has lost its calcium suppressing
abilities, calcium will build up inside the machine. Since the
Water Hardness Selector is off, the machine will not remind you
when to decalcify. If the filter is not replaced, the calcium build-
up will clog and damage your machine.
• Push the Rinse Button. DURATION 2 MIN. / START YES.
Please note: To change and activate the filter at a later time,
turn the Rotary Dial until the display shows START NO. Push the
Rotary Dial to exit the program. In this case the S9 OT will still
remind you with the message CHANGE FILTER.
1. Push Rinse Button again. CHANGE FILTER /PRESS RINSE.
2. Remove the water tank and the old filter and set the extension
rod aside. Important: Keep the extension rod.
Activating:
You must activate the cartridge for the machine to monitor it
properly. Otherwise the S9 OT assumes decalcifying mode.
COFFEE READY.
1. Push the Rotary Dial until display shows MAINTENANCE.
2.Turn the Rotary Dial until the display shows FILTER NO and
push the Rotary Dial to enter the program.
3.Turn the Rotary Dial until FILTER YES is displayed and push
the Rotary Dial. CONFIRMED ꢀis displayed briefly and then
3. Make sure the water tank is empty.
INSERT FILTER/PRESS STEAM. The Rinse button illuminates.
4.Place a 20 oz. container under the frothXpress (Fig. 4) and
turn the frothXpress dial to the 3 o'clock position.
4. Remove the new cartridge from its bag and rinse under
running water. Now install as explained in chapter 13a,
steps 4 through 6.
5.Push the Rinse Button. FILTER RINSING. For the next 60
seconds the machine will push water through the cartridge
23.
Download from Www.Somanuals.com. All Manuals Search And Download.
13c. MANUAL CLEARYL REPLACEMENT
If the filter is more than 2 months old and the display does not
indicate to replace filter, replace as follows.
• Push the Rotary Dial until display shows MAINTENANCE.
Turning the Rotary Dial clockwise the display shows the follow-
ing functions:
COFFEE READY.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Push Rotary Dial again, display shows CLEAN CAPPUCCINO.
Chapter
MAINTENANCE .............. 15.1
PRODUCTS ..................... 14.1 (beverage buttons)
• Turn the Rotary Dial until the display shows CHANGE FILTER. FILTER NO or YES........... 13a
• Push the Rotary Dial. The display shows DURATION 2 MIN./
START YES.
• Push Rotary Dial again. Display shows INSERT FILTER /
PRESS STEAM.
HARDNESS 10ºDh .......... 12b If FILTER YES this function is suppressed.
ECONOMY MODE – ........ 14.3
TIME --.-- ......................... 14.4
UNIT ON/OFF................... 14.5
OFF AFTER ...................... 14.6
RINSES............................. 14.7
INFORMATION................. 14.8
SETTING AM/PM / OZ .. 14.9
LANGUAGE ENGLISH..... 14.10
EXIT
• Now install as explained in chapter 13a, steps 4 through 6.
13d. DO NOT LET THE CLEARYL FILTER DRY OUT!
If the filter is not immersed in water for a few days the granular
inside will dry out and block any water from passing through.
• If machine is not used for a few days, leave some water in the
water tank so the filter will not dry out. Upon using the
machine again, fill the water tank with fresh water and process
approx. 2 oz. of water through the hot water spout. You now
have fresh water for your first cup of coffee.
• If the machine is not used for a longer period of time, empty
the water container and remove the CLEARYL filter. Fill a
glass with at least 2 inches of water and immerse the filter.
Place the glass in the refrigerator.
Please note: to get back to COFFEE READY, turn the Rotary
Dial until the display shows EXIT, then push the Rotary Dial.
14.1 RE-PROGRAMMING BEVERAGE BUTTONS (PRODUCTS)
This program allows you to change all parameters for all bever-
age functions.
The following parameters can be changed, where applicable:
Coffee volume (WATER): for all 1-cup buttons from 0.5 to 8 oz.,
for all 2-cup buttons from 0.5 to 8 oz. per cup (max total 16 oz.)
Coffee strength (AROMA) for all 1 cup buttons choose from five
settings: XMILD, MILD, NORMAL, STRONG, XSTRONG. The
display shows from one to five coffee beans to indicate the
selected strength during brewing.
• When you use the machine again, install the filter.
14. PROGRAMMING
The S9 OT provides programming, maintenance
and look-up functions. With the display at COFFEE READY
you can access the following functions:
24.
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature: for all coffee drinks the temperature can be set to
NORMAL or HIGH
10.Turn the Dial until the display shows TEMPERAT. NORMAL.
11.Push the Rotary Dial to confirm: CONFIRMED ꢀ then
MILK PORTION: steaming can be set from 3 to 120 seconds.
PAUSE: the pause time between milk production and coffee
brewing for the one-touch Cappuccino and Latte Macchiato
buttons can be set from 0 to 60 seconds.
HOT WATER PORTION: can be set from 0.5 to 15 oz.
The temperature for the hot water function can be set to LOW,
NORMAL or XHIGH (for specialty teas and pre-warming cups).
TEMPERAT. NORMAL.
12.Turn the Rotary Dial until the display shows EXIT and push the
Rotary Dial. SELECT PRODUCT.
13.If you do not want to change another button, turn the dial
until the display shows EXIT and push the Rotary Dial:
COFFEE READY.
Example 1:
Example 2:
Re-program the 1-Cup Coffee button to:
Re-program the Latte Macchiato button to:
4 ounces of coffee, mild, normal temperature.
COFFEE READY
3.5 oz. of coffee, extra strong, milk production for 20 seconds,
pause to 10 seconds, temperature stays as is (HIGH).
COFFEE READY
1. Push the Rotary Dial until the display shows MAINTENANCE.
2. Turn the Rotary Dial to PRODUCTS and push the Rotary
Dial. The display shows SELECT PRODUCT.
3. Push the Latte Macchiato button. The display shows the
current coffee volume setting, e.g. COFFEE 2.0 OZ.
4. Push the Rotary Dial, COFFEE 2.0 OZ, and turn the dial until
the display shows COFFEE 3.5 OZ.
1. Push the Rotary Dial until the display shows MAINTENANCE.
2. Turn the Rotary Dial to PRODUCTS and push the Rotary
Dial. The display shows SELECT PRODUCT.
3. Push the 1-CUP COFFEE button. The display shows the
current volume setting, e.g. WATER 5.0 OZ.
4. Push the Rotary Dial: WATER 5.0 OZ and turn the dial until
the display shows WATER 4.0 OZ.
5. Push the Dial to confirm: CONFIRMED ꢀthen WATER 4.0 OZ.
5. Push the Rotary Dial to confirm: CONFIRMED ꢀ then
6. Turn the Rotary Dial until the display shows AROMA and the
current strength setting, e.g. three beans graphic.
COFFEE 3.5 OZ.
7. Push the Rotary Dial, NORMAL with three beans graphic,
and turn the Dial until display shows MILD with two beans.
8. Push the Rotary Dial to confirm: CONFIRMED ꢀ then
MILD with two beans.
9. Turn the Dial until the display shows TEMPERAT. HIGH
and push the Rotary Dial TEMPERAT. HIGH.
6. Turn the Rotary Dial until the display shows AROMA and the
current strength setting, e.g. three beans.
7. Push the Rotary Dial, STRONG with four beans, and turn
the Dial until the display shows XSTRONG with five beans.
8. Push the Rotary Dial to confirm: CONFIRMED ꢀ then
XSTRONG with five beans.
25.
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Turn the Rotary Dial until the display shows MILK 14 SEC
10.Push the dial, MILK 14 SEC, and turn the dial until the
display shows MILK 20 SEC.
6. Push the Rotary Dial to confirm: CONFIRMED ꢀ then
WATER 7 OZ.
7. Turn the Rotary Dial until the display shows EXIT and push
the dial. SELECT PRODUCT.
11.Push the Rotary Dial to confirm: CONFIRMED ꢀ then
MILK 20 SEC.
8. If you do not want to change another button, turn the dial
until the display shows EXIT and push the Rotary Dial:
COFFEE READY.
12.Push the Rotary Dial until the display shows PAUSE 15 SEC.
13.Push the Rotary Dial, PAUSE 15 SEC, and turn the Rotary
Dial until the display shows PAUSE 10 SEC.
14.2 RESTORING FACTORY SETTINGS FOR BEVERAGE
BUTTONS
You can reset the beverage buttons back to the factory setting
14.Push the Rotary Dial to confirm: CONFIRMED ꢀ then
PAUSE 10 SEC.
15.Turn the Rotary Dial until the display shows EXIT and push
the dial. SELECT PRODUCT.
16.If you do not want to change another button, turn the dial
until the display shows EXIT and push the Rotary Dial:
COFFEE READY.
as follows:
The machine is plugged in. Only the main power switch in the
back of the machine is on. The display is blank.
Example: reset the 1-CUP Espresso button.
• Open the cover of the Rotary Dial.
• Push and hold the Rotary Dial and push the 1-Cup Espresso
button for two seconds. The display shows 1 ESPRESSO OK.
The factory setting has been restored.
Example 3:
Change the Hot Water Portion to 7 ounces and and leave the
temperature at XHIGH.
COFFEE READY
14.3 ECONOMY MODES
You can set the machine to three different modes.
ECONOMY MODE – (SAVE NO)
The S9 OT is always ready to brew coffee and produce steam.
The two white indicator lights in the cappuccino and latte
macchiato button are always on.
ECONOMY MODE 1 (SAVE LEVEL 1)
The machine is always ready to brew coffee and is in the
1. Push the Rotary Dial until the display shows MAINTENANCE.
2. Turn the Rotary Dial to PRODUCTS and push the Rotary
Dial. The display shows SELECT PRODUCT.
3. Turn the Selector Dial (Fig. 3.3) on the right side until the
symbol for the Hot Water Portion is illuminated (Fig. 3.1).
Then push the Selector Dial.
4. Display shows the current water portion, e.g. WATER 5 OZ.
5. Push the Rotary Dial, WATER 5 OZ, and turn the dial until
the display shows WATER 7 OZ.
energy saving mode for steam.
26.
Download from Www.Somanuals.com. All Manuals Search And Download.
If the machine is primarily used for coffee this setting saves
energy. The heating element for steam (milk frothing) will shut off
after approx. 10 minutes after last use. At this time the white
indicator lights in the cappuccino and latte macchiato buttons
turn off. To use the steam function, push the cappuccino or latte
macchiato button. The lights will start blinking, indicating that
the thermoblock for steam is heating up. This will take between
5 and 30 seconds depending how much that thermoblock was
cooled down. Once the white indicator lights in those buttons
are illuminated, you can push them again to make cappuccino.
ECONOMY MODE 2 (SAVE LEVEL 2)
This setting will save more energy than economy mode 1.
Choose this setting if you prepare only a few coffees or cappuc-
cinos in large intervals. It is much faster than turning the
machine on and off every time you want to make coffee.
Five minutes after last use the S9 OT will lower the temperature
and enter standby mode. When making coffee at a later time,
the S9 OT will first heat up for 5 and 30 seconds.
Example:
Set the time to 7:15 AM and the weekday to Wednesday.
COFFEE READY
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows TIME -.- / WEEKDAY.
• Push the Dial and turn to TIME and push the dial again.
• Turn the Dial to select the hours 7:00 AM and push to confirm.
• Now turn the Dial to set the minutes: 7:15 AM.
• Push the Dial to confirm. TIME 7:15 AM. CONFIRMED ꢀ,
then TIME 7:15 AM.
• Turn the Dial to WEEKDAY and push the dial.
• Turn the dial until display shows WEDNESDAY and push to
confirm: CONFIRMED ꢀthen WEEKDAY WEDNESDAY.
• Turn Dial to EXIT and push to get back to COFFEE READY.
Please note: For Daylight Saving you have to re-set the time.
Please note: When fully charged, the built-in back-up battery
keeps the clock running for up to eight weeks in case the S9 OT
is unplugged or the main power switch in the back is turned off.
Example:
Change from ECONOMY MODE – to ECONOMY MODE 1
COFFEE READY
• Push and hold the Rotary Dial. MAINTENANCE
• Turn the Dial until the display shows ECONOMY MODE - .
• Push the Dial, SAVE NO and turn to SAVE LEVEL 1 and push
the dial to confirm, CONFIRMED ꢀthen ECONOMY MODE 1.
14.5 AUTO-ON and AUTO-OFF TIMES
You can set a time at which the machine automatically turns on
and is ready to make coffee.
Please note: Auto-on/off times will only work if the actual time is
set and the main power switch is turned on (the small red light in
the On/Off switch is illuminated)
• Turn the Dial to EXIT and push to return to COFFEE READY.
Please note: The Auto-on/off time function will apply to all days.
You can select certain days of the week for the S9 OT not to
turn on automatically. See the following example.
14.4 ACTUAL TIME and WEEKDAY
Setting the time allows you to program auto-on time.
27.
Download from Www.Somanuals.com. All Manuals Search And Download.
Example:
Example:
Set the On-time to 6:15 AM and program the S9OT not to turn
on automatically on Sundays.
Change the auto-off from 5 hours to 2 hours after last use.
COFFEE READY.
COFFEE READY
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows OFF AFTER 5 H.
• Push the Dial OFF AFTER 5 H.
• Turn the dial until display show OFF AFTER 2 H and push to
confirm. CONFIRMED ꢀ, OFF AFTER 2 H.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows UNIT ON/OFF.
• Push the Dial UNIT ON --.--, push again UNIT ON --.--.
• Turn the dial to set the hours UNIT ON 6:00 AM and push the
Dial to confirm. UNIT ON 6:00 AM.
• Turn the dial to EXIT and push. COFFEE READY.
• Turn the Dial to set the minutes UNIT ON 6:15 AM and push
to confirm. CONFIRMED ꢀ, then UNIT ON 6:15 AM.
14.7 RINSE SETTINGS
• Turn the Rotary Dial until ON/OFF / MON YES is displayed
and push ON/OFF / MON YES.
This program allows you to change both the Rinse cycle and the
Cappuccino Rinse cycle.
• Turn the dial until ON/OFF / SUN YES is displayed and push
ON/OFF / SUN YES.
• Turn the dial until display shows ON/OFF / SUN NO and push
to confirm CONFIRMED ꢀand then ON/OFF / SUN NO.
• Turn the dial to EXIT and push. The display shows
ON/OFF / MON YES.
Rinse cycle (INIT RINSE)
After turning the machine on with the On/Off button, the S9 OT
heats up and then prompts you to run a short rinse cycle
(chapter 8). You can re-program this function so that this rinse
cycle is done automatically.
Example:
Change the initial rinse cycle from manual to automatic:
COFFEE READY.
• Turn the dial to EXIT and push. COFFEE READY.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows RINSES and push the
dial. INIT RINSE MANUAL.
• Push the dial again, INIT RINSE MANUAL and turn to
INIT RINSE AUTO and push to confirm. CONFIRMED ꢀ
then INIT RINSE AUTO.
• Turn the dial to EXIT and push the dial RINSES.
• Turn the dial to EXIT and push COFFEE READY.
14.6 AUTO-OFF
The S9 OT is pre-set to turn itself off 5 hours after last use.
You can change the auto-off interval between 0.5 and 15 hours
or you can set the machine not to turn itself off.
Recommendations: If you only use the machine in the morning,
change the auto-off to 2 hours. If you use the machine all day
long, leave the auto/off as is. This way the machine is always
ready, and it is not necessary to turn it on and to warm up.
28.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION / WARNING
14.10 LANGUAGES
In the setting INIT RINSE AUTO the machine will automatically
You can change the display from English to French, Portuguese,
dispense hot water through the Dual Coffee Spouts. Please keep German, Italian, Dutch or Spanish.
children and pets away!
COFFEE READY
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows LANGUAGE ENGLISH.
• Push and turn the Dial until the desired language appears and
push to confirm.
• Turn the Dial to EXIT (in the language you choose).
• Push the Dial to get back to COFFEE READY (in the
language you choose).
Cappuccino rinse cycle (CAPP RINSE)
The S9 OT is factory-set to immediately remind you to run a
rinse cycle after milk use (chapter 10g). This function can be
re-programmed to remind you 10 minutes after last milk use.
14.8 INFORMATION
In this program you can look up
• how many coffees you produced with the individual beverage
buttons,
• how often cleaning, filter change and descaling programs
were performed,
15. CARE AND MAINTENANCE MESSAGES
The machine will automatically display messages. In some cases
the message allows you to continue to brew coffee. In other
cases no further coffee brewing is possible before the task has
been completed.
• how close to the next tablet cleaning program, etc.
PRESS RINSE
14.9 DISPLAY SETTINGS (SETTING AM/PM / OZ)
This function lets you select the time format AM/PM or 24HR
format and the volume either in ounces OZ or milliliters ML.
COFFEE READY
• Push the Rotary Dial until the display shows MAINTENANCE.
• Turn the Dial until the display shows DISPLAY AM/PM / OZ.
• Push and turn the Dial to change the time display and push
the dial to confirm.
Push the Rinse button (Fig. 2,E). The machine pumps hot water
through the coffee spouts or continues a cleaning program.
FILL SYSTEM / PRESS RINSE
Place containers underneath the Auto Cappuccino System
and the Hot Water Spout (Fig. 4) and push the Rinse button
(chapter 6c).
FILL WATER TANK
The water tank is almost empty. Add water before resuming
• Turn Dial to change from OZ to ML and push to confirm.
• Turn the Dial to EXIT and push to return to COFFEE READY.
brewing coffee.
EMPTY GROUNDS or EMPTY TRAY
The used coffee container is full (it holds a maximum of 16
coffee portions). You must empty the coffee container before you
29.
Download from Www.Somanuals.com. All Manuals Search And Download.
can resume brewing coffee.
It is time to decalcify the machine. You can still make coffee,
Make sure the Dual Coffee Spouts are moved upwards. Carefully however we highly recommend to perform the decalcifying cycle
lift and pull out the removable drawer (Fig. 18 and 19). TRAY
MISSING. There is water in the drawer. Empty the drawer and
the used coffee container, assemble and replace. Make sure the
two metal contacts of the drawer are clean and dry.
within the next few days (chapter 17.1).
Please note: If you use the Clearyl cartridge and the message
appears, then your cartridge function was not activated. Follow
the instruction in chapter 13a to program and activate the
cartridge. If the cartridge is already in use for several weeks
Please note: If the machine is not used for a few days, pull out
the tray and empty the used coffee container. Used, moist coffee install a new cartridge.
grounds can develop mold and mildew.
Important: If you pull out the drawer without any corresponding
COFFEE READY / DECALCIFY NOW
It is urgent to decalcify the machine.
message in the display you must empty the used coffee container. COFFEE READY / CHANGE FILTER
The machine assumes that it will be emptied. If you do not empty
the container, used coffee will overflow inside the machine and
cause serious damage to the coffee release mechanism.
Please note: The machine does not sense if the used coffee
container (Fig. 1,16) is inserted. If the used coffee container is
not inserted, ground coffee discharges onto the drawer.
TRAY MISSING
It is time to replace the Clearyl filter (chapter 13b).
NOT ENOUGH PRE-GROUND
Not enough pre-ground coffee was filled into the ground coffee
funnel (Fig. 1,11). The S9 OT stops the operation (chapter 9e).
15.1 MANUAL MAINTENANCE CYCLES
The S9 OT will display when it’s time to perform certain cleaning
Insert the drawer with the empty used coffee container. Make sure programs. You can also manually access these programs and
the metal contacts in the back of the drawer are clean and dry.
perform them.
FILL BEANS
COFFEE READY.
Add beans to the bean container.
COFFEE READY / CLEAN MACHINE
After approx. 220 coffee brewings or 80 initial rinsing cycles you
must run a tablet cleaning cycle. You can still make coffee, how-
ever we highly recommend to perform the cleaning cycle within
the next few days (chapter 16.1).
• Push the Rotary Dial until the display shows MAINTENANCE.
• Push the Dial again, CLEAN CAPPUCCINO.
• Turning the dial shows you which programs you can access:
CLEAN CAPPUCCINO (chapter 15.5)
RINSE MACHINE (see example below in chapter 15.1)
RINSE CAPPUCCINO (chapter 10g)
COFFEE READY / CLEAN NOW
CLEAN MACHINE (chapter 16.1)
After 30 more coffee brewings the message reads CLEAN NOW. DECALCIFY MACHINE (chapter 17.1)
COFFEE READY / DECALCIFY MACHINE CHANGE FILTER (chapter 13c)
30.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you push the Rotary Dial to enter one of the above programs,
the display guides you through the necessary steps.
Please note: If the display shows MAINTENANCE and you do
not select one of the above programs within five seconds, the
S9 OT will return to COFFEE READY.
• Turn the tool counter-clockwise slowly until the stone
becomes loose.
Attention: Do not try to turn the tool clockwise.
• Fold the shield down and replace the screw.
• Turn machine on and test the grinder without beans to see
if the blockage has disappeared.
Example:
Run a manual hot water rinse cycle. COFFEE READY.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Push the Dial again, CLEAN CAPPUCCINO.
• Turn the Dial until the display shows RINSE MACHINE.
• Place a cup under the Dual Coffee Spouts.
15.3 GENERAL CLEANING INSTRUCTIONS
Never use abrasive materials or chemicals to clean the
machine.
• Clean the housing with a soft, damp cloth.
• Rinse water tank daily and fill with fresh cold water.
• Push the Rotary Dial. The S9 OT will push hot water through
the Dual Coffee Spouts and then return to COFFEE READY.
15.4 EMPTYING THE SYSTEM BEFORE TRANSPORT
This procedure is necessary to prevent water and frost damage
in case you intend to transport the machine.
COFFEE READY
• Place a container under the Cappuccino system and the Hot
Water Spout.
• Turn the machine off. The main power switch is still on.
• Press and hold the Rinse button until the display shows
SYSTEM EMPTYING
• A small amount of water is dispensed. When the process is
completed the machine turns itself off.
15.2 REMOVING STONES FROM THE BURR GRINDER
If the burr grinder is blocked, proceed as follows:
• Turn off the machine by pushing the ON/OFF button (Fig. 2,B).
Wait until the machine has shut down completely.
• Turn the main power switch off (Fig 1b).
• Open the bean container lid and remove all beans (scoop out
beans or use a hand-held vacuum cleaner).
• Remove the screw in the bean container (Fig. 23) and
push the grinder shield upwards (Fig. 24) Do not try to
remove the shield completely.
The next time the machine is turned on, the display shows
FILL SYSTEM/PRESS STEAM (chapter 6c).
• If any beans remain, remove them.
• Attach the burr grinder release tool (in Welcome Pack) to the
upper burr (Fig. 25).
• If you cannot find this tool call 1-800-220-5701 and we will
send the tool to you free of charge.
15.5 CLEANING THE FROTHXPRESS
After frothing a few drops of milk remain inside the frothXpress.
The S9 OT displays RINSE CAPPUCCINO. Follow the instruc-
tions in chapter 10g.
31.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you use the frothXpress extensively or forgot to clean it, milk
fat starts building up inside the frothXpress. In this case use the
Cappuccino Cleaner liquid in the Welcome Pack.
Run a CLEAN CAPPUCCINO cycle as follows:
COFFEE READY.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Push the Dial again, CLEAN CAPPUCCINO.
• Push the Dial again. CLEANER FOR CAPPU. The Rinse
button illuminates.
• Remove the frothXpress from the steam nozzle.
• Take the frothXpress apart (Fig. 17a) and set the chrome plated
face aside.
• Place all parts other parts including the hose in a cup with
warm water and add one cap-full (15 ml or 1/2oz.) of the
cappuccino liquid.
• Let sit for ten minutes or overnight.
• Rinse all parts under fresh water and assemble.
• Pour approx. 5 oz. of water into a container and add one
capful (15 ml or 1/2oz.) of the Cappuccino Cleaner liquid.
• Immerse one end of the long milk hose into the cleaning
solution and insert the other end into the frothXpress. Turn
the frothXpress Dial to the 12 o’clock position.
• Place a container under the frothXpress (Fig. 4).
• Push the rinse button. CAPPUCCINO CLEANS. The S9 OT
siphons the cleaning solution through the frothXpress and
stops automatically.
• When the display shows WATER FOR CAPPUCCINO,
remove both containers and empty. Fill fresh water into one
container and insert the hose again. Place the other empty
container under the frothXpress.
16. AUTOMATIC CLEANING CYCLES
16.1 CLEANING WITH SPECIAL TABLET
The machine monitors how many coffees are brewed and how
often the rinsing program is activated. After approx. 220 coffees
the display shows COFFEE READY / CLEAN MACHINE. You
can continue brewing coffee, however we highly recommend
that you clean the machine as described below within the next
few days. This cleaning program will remove oil build-ups in the
brewing chamber. If the display shows CLEAN NOW clean the
machine immediately.
This cleaning program takes about 20 minutes. Please use the
enclosed white cleaning tablet. The machine comes with a pack
of 2 tablets. To re-order see chapter 20.
Important: Once the cleaning program has started do not
interrupt the procedure.
• Push the Rinse button again. CAPPUCCINO CLEANS.
The S9 OT will siphon fresh water through the frothXpress,
removing the cleaning solution. COFFEE READY.
• Squeeze the bottom of the venting tip (Fig. 17a) to make sure
it is clean.
COFFEE READY / CLEAN MACHINE
1. Push the Rinse button. DURATION 20 MIN. / START YES.
Please note: To clean the S9 OT at a later time, turn the Rotary
Dial until the display shows START NO. Push the Rotary Dial to
You can also immerse the frothXpress parts (except the chrome
plated face) into a cappuccino cleaner solution as follows:
32.
Download from Www.Somanuals.com. All Manuals Search And Download.
exit the program. In this case the S9 OT will remind you with the
message CLEAN MACHINE.
2. Make sure that the water container is at least half full.
• Turn the dial until the display shows CLEAN MACHINE
and push the dial. The display shows DURATION 20 MIN. /
START YES.
3. Push the Rinse Button. EMPTY TRAY.
• Continue with the steps 2 through 9 from the chapter 16.1.
4. Remove and empty the tray and the used coffee container
and replace.
17. DECALCIFYING
Attention: If the tray and the used coffee container are
already empty, you still need to remove the tray for approx.
20 seconds and then replace it. PRESS RINSE.
The machine has an integrated decalcifying program. This
program takes 45 minutes. When the display shows COFFEE
READY / DECALCIFY MACHINE it is time to decalcify the
machine. The Rinse button is illuminated. You can still make
coffee. However, it is highly recommended to decalcify the
machine within the next 3 to 4 days.
Please note: If you use the Clearyl water cartridge and the
display shows DECALCIFY MACHINE then your cartridge
function is not activated. Follow the instructions in chapter 13a
to activate the Clearyl Cartridge. If the cartridge is in use for
several weeks install a new cartridge.
Important: The decalcifying program must not be interrupted.
NOTE: Only use our special, square decalcifying tablets
Model # 66281, see chapter 20.
CAUTION: Never use vinegar or any other decalcifying agent.
This might damage internal parts of the machine.
CAUTION: Immediately remove any splashes of the decalcifying
solution from sensitive surfaces, such as natural stone or wood.
CAUTION: If the decalcifying solution comes in contact with the
skin, rinse it off with water. If the solution comes in contact with
your eyes, see a doctor.
5. Place containers (20 oz.) under the coffee spout and the
frothXpress (Fig. 4) and push the Rinse button (Fig. 2.E).
The display shows CLEANS. After a short while you will hear
a beep and the display shows ADD TABLET/PRESS RINSE.
6. Open the ground coffee funnel lid and drop one white tablet
into the opening (Fig. 22). Close lid.
7. Push the Rinse button. The display shows CLEANS. The
machine will start the automatic cleaning program by
dispensing water in intervals into the containers underneath
the spouts. When finished, the display shows EMPTY TRAY.
8. Remove the tray. There will be water in the tray and in the
used coffee container. Empty, clean and replace. The display
shows COFFEE READY.
9. Clean the ground coffee funnel. Remove the funnel and rinse
under hot water and dry Replace funnel (Fig. 20 and 21).
16.2 MANUAL TABLET CLEANING
This program is useful if the brewing process slows down due to
excessive oil build-up inside the machine. COFFEE READY.
• Push and hold the Rotary Dial. MAINTENANCE.
• Push the Rotary Dial, display shows CLEAN CAPPUCCINO.
Important: Always wait until the decalcifying solution in the
water tank has been used up. Do not fill additional decalcifying
solution into the water tank.
33.
Download from Www.Somanuals.com. All Manuals Search And Download.
17.1 DECALCIFYING PROCEDURE
COFFEE READY / DECALCIFY MACHINE
1. Push the Rinse button until display shows
11. Display shows RINSE WATER TANK / FILL WATER TANK.
Remove the water tank, rinse thoroughly, fill it halfway with
fresh water and replace. The display shows PRESS RINSE.
12. Place containers under the auto cappuccino system and the
hot water spout / coffee spouts (Fig. 4).
DURATION 45 MIN. / START YES.
Please note: To start at a later time, turn the Rotary Dial to
START NO and push the Rotary Dial. The machine will still
display COFFEE READY / DECALCIFY MACHINE.
2. Push the Rinse button again, display shows EMPTY TRAY.
3. Remove and empty the tray and the used coffee container
and replace, display shows SOLVENT IN TANK.
Attention: If the tray and the used coffee container are empty,
you must remove the tray for approx. 20 seconds and then
replace it.
13. Push the Rinse button DECALCS.
14. The machine pumps fresh water through the system and
stops automatically. The display shows HEATING UP. When
the display shows MACHINE RINSING, hot water will flow
through the coffee spouts. EMPTY TRAY.
15. Remove and empty the containers. Then carefully remove
and empty the tray and the used coffee container and
replace. COFFEE READY.
4. Remove the frothXpress system from the Auto Cappuccino
system (Fig. 16).
The machine will automatically remind you when it’s time to
decalcify again.
5. Remove the water container and empty.
6. Completely dissolve 3 of the large square decalcifying
tablets in a container with 20 oz. of water (0.6 liters) and
pour the solution into the water tank.
17.2 MANUAL DECALCIFYING
If you use very hard water it is possible that calcium builds up
prematurely. If your coffee does not come out as hot as before
it is a sign for calcium build-up. When this happens you can
7. Replace water tank. SOLVENT IN TANK/PRESS RINSE
8. Place containers under the Auto Cappuccino system and the manually start a decalcifying cycle as follows:
hot water spout (Fig. 4).
COFFEE READY
9. Push the Rinse button. The display shows DECALCS and
the light in the Rinse button flashes during the operation.
The machine pumps the decalcifying solution in intervals
through the Cappuccino system and the hot water spout.
The display shows decalcifying status in the progress bar.
10. When display shows EMPTY TRAY, remove and empty the
containers. Then carefully remove and empty the tray and
the used coffee container and replace.
• Push the Rotary Dial until the display shows MAINTENANCE.
• Push the Rotary Dial, display shows CLEAN CAPPUCCINO.
• Turn the dial until the display shows DECALCIFY MACHINE
and push the dial. The display shows DURATION 45 MIN. /
START YES.
• Continue with the steps 2 through 15 from the chapter 17.1.
34.
Download from Www.Somanuals.com. All Manuals Search And Download.
18. TIPS FOR BETTER COFFEE
machine for a minute.
Height adjustable coffee-spout
Adjust the height of the coffee-spout to the size of your cups.
• Turn machine on again. If the error message comes up again,
try one more time.
Grinding
• If the message persists, call customer service.
Please refer to chapter 7 "Adjusting the Grinder."
Pre-warm cups
TROUBLESHOOTING:
Pre-warm cups in advance with hot water (chapter 9a).
Sugar and cream
Warmth is lost by stirring the contents of the cup. Adding milk
or cream from the refrigerator considerably lowers the tempera-
ture of the coffee.
A. NO COFFEE COMES OUT OF THE COFFEE SPOUT
Reason: Beans in bean container are not feeding properly into
the grinder because they are stuck together.
Solution: Stir beans before grinding and while grinding turn the
grinding selector to the coarsest setting.
When using very oily beans pour the beans onto a plate and let
some of the sticky oils evaporate (this will not harm the aroma of
the coffee).
Reason: You used ground coffee in the ground coffee funnel.
The ground coffee was too fine.
19. ERROR MESSAGES / TROUBLESHOOTING
ERROR MESSAGES:
The machine can display any of the following error messages:
ERROR 1, ERROR 3, ERROR 5
Solution: Use ground coffee which is ground somewhat coarser.
Reason: No water is transported through the system.
Solution: Remove water container and make sure that the con-
necting valve is free of any particles (like a coffee bean etc).
Reason: The ground coffee funnel is clogged; the internal brew-
ing chamber is clogged.
Solution: Place a large cup underneath the coffee spout. Push
the rinse button (Fig. 2E) a few times until the blocked coffee is
removed. (Never fill more than 2 scoops of coffee in the ground
coffee funnel; the funnel is not a storage area for ground coffee).
Also, use a ground coffee which is ground somewhat coarser.
Call our customer service hot line 1-800-220-5701.
Your machine needs to be returned for service.
ERROR 2, ERROR 4
Your machine is too cold. The heating sensor does not react.
• Turn the machine off.
• Keep the machine at normal room temperature (65º F or
higher) for 2 hours .
• Then turn it on again.
If display still shows ERROR 2 or ERROR 4 call customer
service.
ERROR 6, ERROR 7, ERROR 8
• Turn machine off, turn the main power switch off and unplug
35.
Download from Www.Somanuals.com. All Manuals Search And Download.
B. THE DISPLAY READS "FILL WATER TANK" BUT THERE IS
ENOUGH WATER IN THE WATER TANK.
Reason: The floatation device (Fig.1,4) is stuck or missing.
Solution: Clean the water container and make sure the floatation
device moves freely.
Solution: Within the water tank is a small compartment (like a
mouse trap). Inside is a small black floatation device. On top is a
small clear see-through plastic cover. This small plastic cover is
missing and the floatation device is outside of the small com-
partment. Check if you can find both pieces inside the water
tank and put it back together. If you cannot find the pieces call
1-800-220-5701. We will send the pieces FREE OF CHARGE.
c. If any parts are missing call: 1-800-220-5701.
D. GRINDER MAKES AN EXTREMELY LOUD NOISE;
NO BEANS ARE GROUND
Reason: A stone or object is blocking the burr grinder.
Solution: See chapter 15.2.
E. THE REMOVABLE DRAWER (Fig.1, 18) DOESN’T COME OUT
Reason: The internal used coffee disposal chute did not retract.
Solution: Turn off the machine. Wait a minute. Turn machine on
and wait until it stops making any noise. Now try to pull out the
drawer. If this does not work, turn the machine off. Now pull the
drawer out with some force. You will feel some resistance. When
the drawer is out you will see that the back wall of the used cof-
fee container (Fig.1,16) is missing.
C. INSUFFICIENT FROTHED MILK PRODUCTION
Reason: Milk is initially not cold enough or your milk is not
suited for thick frothing.
Solution: Make sure milk is cold. Use a different type of milk.
Skim milk will produce the thickest and longest lasting froth. Full
fat milk will produce less thick froth.
Reason: The components of the frothXpress are not assembled
properly, or the components are clogged with hardened milk, or
one or more of the components are missing.
Reach into the machine and retrieve the back wall (it is a small
black flexible piece). Set the used coffee container aside and
insert the drawer (without the used coffee container) into the
machine. Turn the machine on. Wait until all noise has stopped.
The disposable chute should retract. Remove the drawer,
replace the used coffee container and insert it back into the
machine. Check if the drawer comes out easily.
Solution:
20. SUPPLIES
a. Remove frothXpress. Check that steam comes out of the
steam nozzle. Place a cup underneath the steam nozzle and
use the milk function (chapter 10e). CAUTION: hot steam is
dispensed from the steam nozzle.
If no steam is released stop the milk function and use a
needle to clear blockage inside the steam nozzle.
b. Clean all frothXpress parts and assemble properly (chapter 15.5).
The following supplies are necessary to keep your machine in
good working order:
• Clearyl Water Filter Cartridge (one included).
Model #64553; the machine will remind you automatically.
Tip: If you brew 10 cups a day you need about one Clearyl
cartridge per month. Always keep extra cartridges available.
36.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Special Cleaning Tablets (two included) Model #62205.
Tip: If you brew 10 cups a day you need about one tablet
every 3 weeks. Always keep extra tablets available.
• Auto-Cappuccino Cleaner (one bottle included).
Model #63801
Tip: If you use the auto cappuccino cleaner every other day
you need a new bottle every 5 weeks.
• Decalcifying tablets (large square tablets) - Model #66281.
Please note: You must use decalcifying tablets if you do not
use the Clearyl cartridge.
this warranty.
In case the machine cannot be repaired, JURA-CAPRESSO will
replace your machine with the same model with the same or less
usage. In case we cannot replace your machine with the same
model we will replace it with a model of the same or higher retail
value with the same or less usage. Usage is defined by the
number of coffees the machine has made when sent for repair.
TRANSPORT: When sending the machine, use the original packing,
the inner and outer cartons or use approximately 2” of bubble wrap
and insert machine in a carton which will hold 40lbs.
Any damage in transit is NOT covered by this warranty.
THIS WARRANTY DOES NOT COVER:
• Any machine NOT distributed by JURA-CAPRESSO within the
United States.
• Any machine not purchased from an Authorized Jura-
Capresso Dealer. (Call our customer service department to
check for authorized dealers).
You can order these supplies:
• with the enclosed mail order form or
• by calling our customer service center at 1-800-220-5701.
21. LIMITED TWO-YEAR WARRANTY
Please note: This warranty will be void if the Warranty / Product
Registration has not been received two weeks after the purchase
date (you can fax or mail the registration or you can register
through our website www.capresso.com)
This limited warranty covers your new Jura-Capresso
S9 One-Touch Series for two years or up to 6,000 coffee
brewings, whichever comes first.
This warranty is in effect for the period and usage described
above from the date of the first purchase and is limited to the
United States of America. This warranty covers all defects in
materials or workmanship (parts and labor) including free UPS
ground transportation for both ways within the continental
United States. For Hawaii and Alaska freight is not covered by
• Any machine purchased through EBAY.
• Damage caused by accident, abuse, negligence, misuse,
• improper operation or failure to follow instructions contained in
this manual.
• Any service or alteration performed by an unauthorized person,
company or association.
• Damage caused by neglecting and omitting maintenance,
cleaning and decalcifying cycles.
• Damage caused by use of instant coffee or any other ingredients
not allowed in this product.
Other limitations and exclusions:
Any implied warranties including fitness for use and merchantability
are limited in duration to the period of the express warranty
37.
Download from Www.Somanuals.com. All Manuals Search And Download.
set forth above and no person is authorized to assume for
JURA-CAPRESSO any other liability in connection with the
sale of the machine. JURA-CAPRESSO expressly disclaims
liability for incidental and consequential damages caused by
the machine. The terms "incidental damages" refer to the loss
of the original purchasers time, loss of the use of the machine
or other costs relating to the care and custody of the machine.
The terms "consequential damages" refer to the cost of repairing
or replacing other property which is damaged when this machine
does not work properly. Any loss of income is excluded. The
remedies provided under this warranty are exclusive and in lieu
of all others. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
22. FREE REPAIR SERVICE / EXTRA REPAIR COVERAGE
Within the warranty period all repairs are free of charge including
both ways UPS ground transportation to and from our service
facilities within the continental United States.
For Hawaii and Alaska freight is not covered by this warranty.
In case the machine cannot be repaired, JURA-CAPRESSO will
replace your machine with the same model with the same or less
usage. In case we cannot replace your machine with the same
model we will replace it with a model of the same or higher retail
value with the same or less usage. Usage is defined by the
number of coffees the machine has made when sent for repair.
Within four weeks after your product registration you can
purchase an extra 12 months of repair coverage. For details see
the literature enclosed with this product.
38.
Download from Www.Somanuals.com. All Manuals Search And Download.
Jura-Capresso Inc.
81 Ruckman Road, Closter, NJ 07624
201-767-3999 • Fax: 201-767-9684
Customer Service: 1-800-220-5701
Download from Www.Somanuals.com. All Manuals Search And Download.
|