Operator’s manual (EPA)
Please read the operator’s manual carefully and
make sure you understand the instructions
before using the machine.
BC 2125
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
Note the following before starting:
KEY TO SYMBOLS
Please read the operator’s manual carefully.
Symbols .......................................................................
CONTENTS
Maintenance, replacement, or repair of the emission control
devices and system may be performed by any nonroad
engine repair establishment or individual.
Contents ......................................................................
Note the following before starting: ................................
INTRODUCTION
WARNING! Long-term exposure to noise can
Dear customer! ............................................................
WHAT IS WHAT?
5
result in permanent hearing impairment. So
always use approved hearing protection.
!
What is what? ..............................................................
SAFETY INSTRUCTIONS
WARNING! Under no circumstances may the
design of the machine be modified without
the permission of the manufacturer. Always
use genuine accessories. Non-authorized
modifications and/or accessories can result
in serious personal injury or the death of the
operator or others.
Important ......................................................................
Personal protective equipment .....................................
Machine′s safety equipment ........................................
!
Cutting equipment ........................................................ 10
ASSEMBLY
Assembling the handlebar and throttle ........................ 12
Assembling the handlebar and throttle ........................ 12
Transport position, handlebar ...................................... 13
Assembling the cutting equipment ............................... 13
Fitting a blade guard, grass blade and grass cutter ..... 13
Fitting the blade guard and saw blade ......................... 14
Fitting the trimmer guard and Auto 32 trimmer head ... 14
Fitting other guards and cutting attachments ............... 15
Adjusting the harness and clearing saw ...................... 15
Standard harness ........................................................ 15
FUEL HANDLING
Your warranty may not cover damage or
liability caused by the use of non-authorized
accessories or replacement parts.
WARNING! A clearing saw, brushcutter or
trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
!
Fuel safety ................................................................... 16
Fuel .............................................................................. 16
Fueling ......................................................................... 17
STARTING AND STOPPING
JONSERED HUSKVARNA SWEDEN
IMPORTANT ENGINE INFORMATION
TWC
Check before starting ................................................... 18
Starting and stopping ................................................... 18
WORKING TECHNIQUES
THIS ENGINE CONFORMS TO U.S. EPA PH1
FOR SMALL NON - ROAD ENGINES.
REFER TO OPERATOR`S MANUAL FOR
General working instructions ....................................... 20
MAINTENANCE
MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
This label certify that the product has been certified in
accordance with American exhaust requirements EPA 1.
Carburetor .................................................................... 24
Muffler .......................................................................... 26
Cooling system ............................................................ 26
Bevel gear .................................................................... 26
Air filter ......................................................................... 27
Spark plug .................................................................... 27
Maintenance schedule ................................................. 28
TECHNICAL DATA
Technical data .............................................................. 29
FEDERAL EMISSION CONTROL WARRANTY
STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS ..... 30
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear customer!
Congratulations on your choice to buy a Jonsered product!
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who
sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s
manual as a valuable document.By following its′ content (using, service, maintenance etc) the life span and the second-hand value
of the machine can be extended. If you ever lend or sell this machine, make sure that the borrower or buyer gets the operator′s
manual, so they will also know how to properly maintain and use it.
Good luck on using your Jonsered machine!
Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance
of products without prior notice.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
30
17
31
18
19
20
22
J
O
N
S
E
R
E
D
S
E
R
V
I
C
E
24
21
21
4
4
28
23
25
27
26
What is what?
1
2
3
4
5
6
7
8
9
Blade
17 Handle adjustment
18 Locking nut
Grease filler cap, bevel gear
Bevel gear
19 Support flange
20 Support cup
Cutting attachment guard
Shaft
21 Drive disc
Handlebar
22 Trimmer head
23 Socket spanner
24 Operator’s manual
25 Transport guard
26 Allen key
Throttle control
Stop switch
Throttle lockout
10 Support eyes for harness
11 Cylinder cover
12 Starter handle
13 Fuel tank
27 Locking pin
28 Harness
29 Start throttle button
30 Adjusting the throttle wire
14 Choke control
15 Air purge
31 Spark plug cap and spark plug
16 Air filter cover
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Important
Personal protective equipment
IMPORTANT!
IMPORTANT!
The machine is only designed for trimming grass, grass
clearing and/or forestry clearing.
A clearing saw, brushcutter or trimmer can be dangerous if
used incorrectly or carelessly, and can cause serious or
fatal injury to the operator or others. It is extremely
important that you read and understand the contents of this
operator’s manual.
The only accessories you can operate with this engine unit
are the cutting attachments we recommend in the chapter
on Technical data.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen. Ask
your dealer for help in choosing the right equipment.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect your
vision, your judgement or your co-ordination.
Never use the machine in extreme weather conditions such
as severe cold, very hot and/or humid climates.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
WARNING! Listen out for warning signals or
shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
!
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual.Some maintenance and service measures must be
carried out by trained and qualified specialists. See
instructions under the heading Maintenance.
HELMET
A helmet should be worn if the trees being cleared are taller
than 2 m.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition lead
are undamaged to avoid the risk of electric shock.
HEARING PROTECTION
The machine operator must ensure that no people or
animals come closer than 15 metres while working. When
several operators are working in the same area the safety
distance should be at least twice the tree height and no less
than 15 metres.
Wear hearing protection that provides adequate noise
reduction.
WARNING! The ignition system of this
machine produces an electromagnetic field
during operation.This field may under some
EYE PROTECTION
!
Always wear approved eye protection. If you use a visor then
you must also wear approved protective goggles. Approved
protective goggles must comply with standard ANSI Z87.1 in
the USA or EN 166 in EU countries.
circumstances interfere with pacemakers.To
reduce the risk of serious or fatal injury, we
recommend persons with pacemakers to
consult their physician and the pacemaker
manufacturer before operating this machine.
WARNING! Running an engine in a confined
or badly ventilated area can result in death
due to asphyxiation or carbon monoxide
poisoning.
!
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
WARNING! Never allow children to use or be
in the vicinity of the machine. As the
machine is equipped with a spring-loaded
!
stop switch and can be started by low speed
and force on the starter handle, even small
children under some circumstances can
produce the force necessary to start the
machine.This can mean a risk of serious
personal injury.Therefore remove the spark
plug cap when the machine is not under
close supervision.
BOOTS
Wear boots with steel toe-caps and non-slip sole.
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
CLOTHING
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Wear clothes made of a strong fabric and avoid loose clothing
that can catch on twigs and branches. Always wear heavy,
long pants. Do not wear jewellery, shorts sandals or go
barefoot. Secure hair so it is above shoulder level.
FIRST AID KIT
Always have a first aid kit nearby.
Press the throttle lockout and make sure it returns to its
original position when you release it.
′
Machine s safety equipment
This section describes the machine′s safety equipment, its
purpose, and how checks and maintenance should be carried
out to ensure that it operates correctly. See the ”What is
what?” section to locate where this equipment is positioned
on your machine.
Check that the throttle control and throttle lockout move freely
and that the return springs work properly.
The life span of the machine can be reduced and the risk of
accidents can increase if machine maintenance is not carried
out correctly and if service and/or repairs are not carried out
professionally. If you need further information please contact
your nearest servicing dealer.
IMPORTANT! All servicing and repair work on the machine
requires special training. This is especially true of the
machine′s safety equipment.If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee the
availability of professional repairs and service. If the retailer
who sells your machine is not a servicing dealer, ask him for
the address of your nearest service agent.
See instructions under the heading Start. Start the machine
and apply full throttle. Release the throttle and check that the
cutting attachment stops and remains at a standstill. If the
cutting attachment rotates with the throttle in the idle position
then the carburettor idle setting must be checked. See
instructions under the heading Maintenance.
WARNING! Never use a machine with faulty
safety equipment.The machine’s safety
equipment must be checked and maintained
as described in this section. If your machine
fails any of these checks contact your
service agent to get it repaired.
!
Throttle lockout
Stop switch
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock (A)
(i.e.when you grasp the handle) it releases the throttle control
(B). When you release the handle the throttle control and the
throttle lockout both move back to their original positions.This
movement is controlled by two independent return springs.
This arrangement means that the throttle control is
automatically locked at the idle setting.
Use the stop switch to switch off the engine.
A
Start the engine and make sure the engine stops when you
move the stop switch to the stop setting.
B
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Regularly check the vibration damping units for cracks or
deformation. Check that the vibration damping element is
undamaged and securely attached.
Cutting attachment guard
WARNING! Overexposure to vibration can
lead to circulatory damage or nerve damage
in people who have impaired circulation.
This guard is intended to prevent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting attachment.
!
Contact your doctor if you experience
symptoms of overexposure to vibration.
Such symptoms include numbness, loss of
feeling, tingling, pricking, pain, loss of
strength, changes in skin colour or
condition.These symptoms normally appear
in the fingers, hands or wrists.The risk
increases at low temperatures.
Check that the guard is undamaged and not cracked.Replace
the guard if it has been exposed to impact or is cracked.
Quick release
There is an easily accessible, quick release fitted at the front
as a safety precaution in case the engine catches fire, or in
any other situation that requires you to free yourself from the
machine and harness. See instructions under the heading
Adjusting the harness and clearing saw.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
Vibration damping system
Check that the harness straps are correctly positioned. Once
the harness and machine have been adjusted, check that the
harness quick release works correctly.
Your machine is equipped with a vibration damping system
that is designed to reduce vibration and make operation
easier.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
Using incorrectly wound cord or a blunt or incorrect cutting
attachment (wrong type or incorrectly filed, see instructions
under the heading Filing the blade) increases the level of
vibration.
The machine′s vibration damping system reduces the transfer
of vibration between the engine unit/cutting equipment and
the machine′s handle unit.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with a
spark arrestor screen. Check whether the muffler on your
machine is fitted with this kind of screen.
For mufflers it is very important that you follow the instructions
on checking, maintaining and servicing your machine.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Never use a machine that has a faulty muffler.
Locking nut
A locking nut is used to secure some types of cutting
attachment.
Regularly check that the muffler is securely attached to the
machine.
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove it,
undo the nut in the same direction as the cutting attachment
rotates. (CAUTION! The nut has a left-hand thread.) Tighten
the nut using the socket spanner.
If the muffler on your machine is fitted with a spark arrestor
screen this must be cleaned regularly. A blocked screen will
cause the engine to overheat and may lead to serious
damage.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
When loosening and tightening the saw blade nut, there is a
risk of injury from the teeth of the saw blade.You should
therefore always ensure that your hand is shielded by the
blade guard when doing this. Always use a socket spanner
with a shaft that is long enough to allow this.The arrow in the
diagram shows the area where you should operate the socket
spanner when loosening or tightening the nut.
!
WARNING! The inside of the muffler contain
chemicals that may be carcinogenic. Avoid
contact with these elements in the event of a
damaged muffler.
!
WARNING! Bear in mind that:
!
The exhaust fumes from the engine are hot
and may contain sparks which can start a
fire. Never start the machine indoors or near
combustible material!
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
General rules
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
•
•
•
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
IMPORTANT!
Keep the teeth of the blade correctly sharpened! Follow our
instructions and use the recommended file gauge. An
incorrectly sharpened or damaged blade increases the risk of
accidents.
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to check
the correct way to load the cord and the correct cord
diameter.
Keep the teeth of the blade correctly sharpened! Follow our
recommendations. Also refer to the instructions on the
blade packaging.
Maintain the correct blade setting! Follow our instructions
and use the recommended file gauge.
Keep the correct setting on the saw blade! Follow our
instructions and use the recommended setting tool. An
incorrectly set saw blade increases the risk of jamming and
blade thrust, and damage to the saw blade.
WARNING! Always stop the engine before
doing any work on the cutting attachment.
This continues to rotate even after the
throttle has been released. Ensure that the
cutting attachment has stopped completely
and disconnect the HT lead from the spark
plug before you start to work on it.
!
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
WARNING! Using an incorrect cutting
attachment or an incorrectly sharpened
blade increases the risk of blade thrust.
!
Cutting equipment
Saw blades are intended for cutting fibrous types of wood.
Sharpening grass cutters and grass
blades
Grass blades and grass cutters are intended for cutting
coarse grass.
•
•
See the cutting attachment packaging for correct
sharpening instructions. Sharpen blades and cutters
using a single-cut flat file.
Sharpen all edges equally to maintain the balance of the
blade.
A trimmer head is intended for trimming grass.
WARNING! Always discard a blade that is
bent, twisted, cracked, broken or damaged
in any other way. Never attempt to straighten
a twisted blade so that it can be reused. Only
use original blades of the specified type.
!
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Sharpening the saw blade
Trimmer head
IMPORTANT!
Always ensure the trimmer cord is wound tightly and evenly
around the drum, otherwise the machine will generate
harmful vibration.
•
See the cutting attachment packaging for correct
sharpening instructions.
A correctly sharpened blade is essential for working efficiently
and to avoid unnecessary wear to the blade and clearing saw.
•
Only use the recommended trimmer heads and trimmer
cords.These have been tested by the manufacturer to suit
a particular engine size.This is especially important when
a fully automatic trimmer head is used. Only use the
recommended cutting attachment. See the chapter on
Technical data.
•
•
Smaller machines generally require small trimmer heads
and vice versa. This is because when clearing using a
cord the engine must throw out the cord radially from the
trimmer head and overcome the resistance of the grass
being cleared.
•
•
Make sure that the blade is well supported when you file
it. Use a 5.5 mm round file with a file holder.
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
•
•
Make sure that the cutter on the trimmer guard is intact.
This is used to cut the cord to the correct length.
The filing angle is 15°. File alternate teeth to the right and
those in between to the left. If the blade has been heavily
pitted by stones it may be necessary to dress the top
edges of the teeth with a flat file, in exceptional cases. If
so, this should be done before filing with a round file. The
top edges must be filed down by the same amount for all
the teeth.
To increase the life of the cord it can be soaked in water
for a couple of days.This will make the line tougher so that
it lasts longer.
Adjust the blade setting. This should be 1 mm.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the handlebar and
throttle
Assembling the handlebar and
throttle (turnable handlebar)
•
•
Remove the screw at the rear of the throttle handle.
•
•
Remove the screw at the rear of the throttle handle.
Slide the throttle handle onto the right side of the
handlebar, (see diagram).
Slide the throttle handle onto the right side of the
handlebar, (see diagram).
•
Align the screw hole in the throttle handle with the hole in
the handlebar.
•
Align the screw hole in the throttle handle with the hole in
the handlebar.
•
•
Refit the screw in the hole in the rear of the throttle handle.
•
•
Refit the screw in the hole in the rear of the throttle handle.
Screw the screw through the handle and handlebar.
Tighten it.
Screw the screw through the handle and handlebar.
Tighten it.
•
•
Unscrew the knob from the handlebar mounting.
•
Fit the mounting components as shown.
Position the handlebar as shown. Fit the mounting
components and tighten the knob lightly.
•
The handle mounting must be fitted between the arrows
on the shaft.
•
•
Loosely tighten the four screws.
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness. Tighten the screws.
•
Put on the harness and hang the machine from the
support hook. Now make a final adjustment so that the
machine is in a comfortable working position when it
hangs from the harness. Tighten the knob.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Transport position, handlebar
Fitting a blade guard, grass blade
and grass cutter
•
•
•
The handlebar can easily be turned to fit along the shaft
for easier transportation and storage.
G
Loosen the knob.Turn the handlebar clockwise so that the
throttle handle rests against the engine.
F
E
Now twist the handlebar around the shaft. Tighten the
knob.
D
B
C
A
•
Fit the transport guard to the cutting attachment.
•
Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt.
Assembling the cutting equipment
CAUTION! Use the recommended blade guard. See the
Technical data section.
WARNING!
!
When fitting the cutting attachment it is
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or
fatal personal injury.
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D), support cup (E) and support flange
(F) on the output shaft.
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
guard as possible. To tighten the nut, turn the spanner in
the opposite direction to the direction of rotation (Caution!
left-hand thread).
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
!
IMPORTANT! If a saw blade or grass blade are to be used
the machine must be equipped with the correct handlebar,
blade guard and harness.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
arrow in the diagram shows the area where you should
operate the socket spanner when loosening or tightening
the nut.
Fitting the blade guard and saw
blade
K
J
Fitting the trimmer guard and Auto
32 trimmer head
H
I
A
L
K
L
•
Remove the mounting plate (H). Fit the adapter (I) and
bracket (J) with the two screws (K) as shown. Fit the blade
guard (A) to the adapter using the 4 screws (L) as shown.
G
K
F
B
C
I
J
I
CAUTION! Use the recommended blade guard. See the
Technical data section.
G
F
A
D
•
Fit the correct trimmer guard (A) for use with the trimmer
head. Hook the trimmer guard/combination guard onto
the fitting on the shaft and secure with the bolt (L).
B
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
C
•
•
Insert the locking pin (C) in the hole to lock the shaft.
•
•
Fit the drive disc (B) on the output shaft.
To fit the trimmer head, first separate the two halves (see
diagram). Proceed as follows:
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
- Insert a finger into the centre hole of the cover (I) while
•
•
Insert the locking pin (C) in the hole to lock the shaft.
grasping the cover with your other fingers. Using the index
finger and thumb of your other hand, release the two catches
(J) that engage in the cut-outs in the bottom half (K). Pull
apart the trimmer head, grasping the cover firmly.
Place the blade (D) and support flange (F) on the output
shaft.
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
guard as possible. To tighten the nut, turn the spanner in
the opposite direction to the direction of rotation (Caution!
left-hand thread).
•
Place the cover (I) and the support flange (F) on the
output shaft.
•
Fit the nut (G). Tighten the nut to a torque of 35-50 Nm
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible.
•
To tighten the nut, turn the spanner in the opposite
direction to the direction of rotation (Caution! left-hand
thread).
•
When loosening and tightening the saw blade nut, there is
a risk of injury from the teeth of the saw blade.You should
therefore always ensure that your hand is shielded by the
blade guard when doing this. Always use a socket
spanner with a shaft that is long enough to allow this.The
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
•
Fit the bottom half of the trimmer head (K) to the cover (I)
by pressing them together, with the cut-outs on the bottom
half aligned with the catches on the cover.
Standard harness
Quick release
At the front is an easily accessible, quick release. Use this if
the engine catches fire or in any other emergency situation
that requires you to free yourself from the machine and
harness.
•
To dismantle, follow the instructions in the reverse order.
Fitting other guards and cutting
attachments
•
Fit the trimmer guard/combination guard (A) intended for
use with the trimmer head/plastic blades. Hook the guard
onto the fitting on the shaft and secure it with the bolt (L).
Spreading the load on your shoulders
A well-adjusted harness and machine makes work much
easier. Adjust the harness for the best working position.
Tension the side straps so that the weight is evenly distributed
across both shoulders.
L
B
C
A
Correct height
Adjust the shoulder strap so that the cutting attachment is
parallel to the ground.
•
•
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
•
•
Insert the locking pin (C) in the hole to lock the shaft.
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
H
H
Correct balance
Let the cutting attachment rest lightly on the ground. If you
use a saw blade it should balance about 10 cm above the
ground to prevent contact with stones and the like. Adjust the
position of the suspension ring to balance the clearing saw
correctly.
•
To dismantle, follow the instructions in the reverse order.
Adjusting the harness and clearing
saw
WARNING! When using a clearing saw it
must always be hooked securely to the
harness. Otherwise you will be unable to
control the clearing saw safely and this can
result in injury to yourself or others. Never
use a harness with a defective quick release.
!
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Gasoline
Fuel safety
Never start the machine:
1
2
If you have spilled fuel on it.Wipe off the spillage and allow
remaining fuel to evaporate.
CAUTION! Always use a quality gasoline/oil mixture with an
octane rating of at least 87 octane ((RON+MON)/2). If your
machine is equipped with a catalytic converter (see chapter
on Technical data) always use a good quality unleaded
gasoline/oil mixture.Leaded gasoline will destroy the catalytic
converter.
If you have spilled fuel on yourself or your clothes, change
your clothes.Wash any part of your body that has come in
contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for leaks
from the fuel cap and fuel lines.
Use low-emission gasoline, also known as alkylate gasoline,
if it is available.
Transport and storage
•
Store and transport the machine and fuel so that there is
no risk of any leakage or fumes coming into contact with
sparks or naked flames, for example, from electrical
machinery, electric motors, electrical relays/switches or
boilers.
•
•
When storing and transporting fuel always use approved
containers intended for this purpose.
This engine is certified to operate on unleaded gasoline.
•
The lowest recommended octane grade is 87
When storing the machine for long periods the fuel tank
must be emptied.Contact your local gas station to find out
where to dispose of excess fuel.
((RON+MON)/2). If you run the engine on a lower octane
grade than 87 so-called knocking can occur. This gives
rise to a high engine temperature and increased bearing
load, which can result in serious engine damage.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
•
When working at continuous high revs a higher octane
rating is recommended.
The transport guard must always be fitted to the cutting
attachment when the machine is being transported or in
storage.
Two-stroke oil
•
For best results and performance use JONSERED two-
stroke engine oil, which is specially formulated for our air-
cooled two stroke-engines.
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion and
inhaling fumes.
!
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
Fuel
•
•
Never use oil intended for four-stroke engines.
Mixing ratio
CAUTION!The machine is equipped with a two-stroke engine
and must always been run using a mixture of gasoline and
two-stroke engine oil. It is important to accurately measure
the amount of oil to be mixed to ensure that the correct
mixture is obtained.When mixing small amounts of fuel, even
small inaccuracies can drastically affect the ratio of the
mixture.
1:50 (2%) with JONSERED two-stroke oil.
Two-stroke oil, litre
Gasoline, litre
2% (1:50)
5
0,10
10
0,20
WARNING! Fuel and fuel fumes are highly
inflammable and can cause serious injury
when inhaled or allowed to come in contact
with the skin. For this reason observe
caution when handling fuel and make sure
there is adequate ventilation.
15
0,30
!
20
0,40
US gallon
US fl. oz.
2 1/2
6 1/2
12 7/8
1
2 1/2
5
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing
Fueling
•
Always mix the gasoline and oil in a clean container
intended for fuel.
•
Always start by filling half the amount of the gasoline to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
WARNING!Taking the following precautions,
will lessen the risk of fire:
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
!
Do not smoke or place hot objects near fuel.
Always shut off the engine before refuelling.
Always stop the engine and let it cool for a
few minutes before refuelling.
When refuelling, open the fuel cap slowly so
that any excess pressure is released gently.
Tighten the fuel cap carefully after refuelling.
Always move the machine away from the
refuelling area before starting.
•
•
Do not mix more than one month’s supply of fuel at a time.
•
•
Clean the area around the fuel cap. Contamination in the
tank can cause operating problems.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Ensure that the fuel is well mixed by shaking the container
before filling the tank.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Check before starting
Starting and stopping
•
Check the blade to ensure that no cracks have formed at
the bottom of the teeth or by the centre hole. The most
common reason why cracks are formed is that sharp
corners have been formed at the bottom of the teeth while
sharpening or that the blade has been used with dull
teeth. Discard a blade if cracks are found.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
!
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the cutting
attachment cannot come into contact with
any object.
Make sure no unauthorised persons are in
the working area, otherwise there is a risk of
serious personal injury.The safety distance
is 15 metres.
•
Check that the support flange is not cracked due to fatigue
or due to being tightened too much. Discard the support
flange if it is cracked.
Starting
Primer bulb: Press the air purge repeatedly until fuel begins
to fill the bulb. The bulb need not be completely filled.
•
•
Ensure the locking nut has not lost its captive force. The
nut lock should have a locking force of at least 1.5 Nm.
The tightening torque of the locking nut should be 35-50
Nm.
Choke: Set the choke control in the choke position.
Check that the blade guard is not damaged or cracked.
Replace the blade guard if it is exposed to impact or is
cracked.
WARNING! When the engine is started with
the choke in either the choke or start throttle
positions the cutting attachment will start to
rotate immediately.
!
•
Check that the trimmer head and trimmer guard are not
damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or are
cracked.
Hold the body of the machine on the ground using your left
hand (CAUTION! Not with your foot!). Grip the starter handle,
slowly pull out the cord with your right hand until you feel
some resistance (the starter pawls grip), now quickly and
powerfully pull the cord.Never wrap the starter cord around
your hand
Repeat pulling the cord until the engine starts. When the
engine starts. return choke control to run position and apply
full throttle; the throttle will automatically disengage from the
start setting.
•
•
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged before
you start the machine.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully extended.
This can damage the machine.
CAUTION!
Do not put any part of your body in marked area. Contact can
result in burns to the skin, or electrical shock if the spark plug
cap has been damaged. Always use gloves. Do not use a
machine with damaged spark plug cap.
For throttle handles with a start throttle
lock:
Set the throttle to the start position by first pressing the throttle
lockout and the throttle trigger, then pressing the start throttle
button (A). Then release the throttle lockout and the throttle
trigger, followed by the start throttle button. The throttle
function is now activated. To return the engine to idle, press
the throttle lockout and throttle trigger again.
Stopping
The engine is switched off by moving the stop switch to the
stop position.
CAUTION! The stop switch automatically returns to the start
position. In order to prevent unintentional starting, the spark
plug cap must be removed from the spark plug when
assembling, checking and/or performing maintenance.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
6
7
Keep a good balance and a firm foothold.
General working instructions
Always hold the machine with both hands. Hold the
machine on the right side of your body.
IMPORTANT!
This section describes the basic safety precautions for
working with clearing saws and trimmers.
If you encounter a situation where you are uncertain how to
proceed you should ask an expert. Contact your dealer or
your service workshop.
Avoid all usage which you consider to be beyond your
capability.
You must understand the difference between forestry
clearing, grass clearing and grass trimming before use.
8
9
Keep the cutting attachment below waist level.
Basic safety rules
Switch off the engine before moving to another area. Fit
the transport guard before carrying or transporting the
equipment any distance.
10 Never put the machine down with the engine running
unless you have it in clear sight.
1
•
Look around you:
To ensure that people, animals or other things cannot
affect your control of the machine.
The ABC of clearing
•
To ensure that people, animals, etc., do not come into
contact with the cutting attachment or loose objects that
are thrown out by the cutting attachment.
•
•
•
•
•
•
•
•
Always use the correct equipment.
Make sure the equipment is well adjusted.
Follow the safety precautions.
•
CAUTION! Do not use the machine unless you are able to
call for help in the event of an accident.
Organise your work carefully.
2
Inspect the working area. Remove all loose objects, such
as stones, broken glass, nails, steel wire, string, etc. that
could be thrown out or become wrapped around the
cutting attachment.
Always use full throttle when starting to cut with the blade.
Always use sharp blades.
Avoid stones.
3
4
Do not use the machine in bad weather, such as dense
fog, heavy rain, strong wind, intense cold, etc. Working in
bad weather is tiring and often brings added risks, such as
icy ground, unpredictable felling direction, etc.
Control the felling direction (take advantage of the wind).
WARNING! Neither the operator of the
machine nor anyone else may attempt to
remove the cut material while the engine is
running or the cutting equipment is rotating,
as this can result in serious injury.
Make sure you can move and stand safely.Check the area
around you for possible obstacles (roots, rocks, branches,
ditches, etc.) in case you have to move suddenly. Take
great care when working on sloping ground.
!
Stop the engine and cutting equipment
before you remove material that has wound
around the blade shaft as otherwise there is
a risk of injury.The bevel gear can get hot
during use and may remain so for a while
afterwards.You could get burnt if you touch
it.
WARNING! Watch out for thrown objects.
Always wear approved eye protection. Never
lean over the cutting attachment guard.
Stones, rubbish, etc. can be thrown up into
the eyes causing blindness or serious injury.
5
Take great care when cutting a tree that is under tension.
A tree that is under tension may spring back to its normal
position before or after being cut. If you position yourself
incorrectly or make the cut in the wrong place the tree may
hit you or the machine and cause you to lose control. Both
situations can cause serious personal injury.
!
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be kept outside the safety zone of 15
m. Stop the machine immediately if anyone
approaches. Never swing the machine
around without first checking behind you to
make sure no-one is within the safety zone.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
•
You should plan the strip so that you avoid going over
WARNING! Sometimes branches or grass
get caught between the guard and cutting
attachment. Always stop the engine before
cleaning.
ditches or other obstacles on the ground.You should also
orient the strip to take advantage of wind conditions, so
that cleared stems fall in the cleared area of the stand.
!
Working methods
WARNING! Machines fitted with saw blades
or grass blades can be thrown violently to
the side when the blade comes into contact
with a fixed object.This is called blade
thrust. A blade thrust can be violent enough
to cause the machine and/or operator to be
propelled in any direction, and possibly lose
control of the machine. Blade thrust can
occur without warning if the machine snags,
stalls or binds. Blade thrust is more likely to
occur in areas where it is difficult to see the
material being cut.
!
Forestry clearing using a saw blade
•
The risk of blade thrust increases with increasing stem
size.You should therefore avoid cutting with the area of
the blade between 12 o’clock and 3 o’clock.
Avoid cutting with the area of the blade
between the 12 o’clock and 3 o’clock
positions. Because of the speed of rotation
of the blade, blade thrust can occur if you
attempt to cut thick stems with this area of
the blade.
•
Before you start clearing, check the clearing area, the
type of terrain, the slope of the ground, whether there are
stones, hollows etc.
•
To fell to the left, the bottom of the tree should be pushed
to the right. Tilt the blade and bring it diagonally down to
the right, exerting firm pressure. At the same time push
the stem using the blade guard. Cut with the area of the
blade between 3 o’clock and 5 o’clock. Apply full throttle
before advancing the blade.
•
•
Start at whichever end of the area is easiest, and clear an
open space from which to work.
Work systematically to and fro across the area, clearing a
width of around 4-5 m on each pass. This exploits the full
reach of the machine in both directions and gives the
operator a convenient and varied working area to work in.
•
To fell to the right, the bottom of the tree should be pushed
to the left. Tilt the blade and bring it diagonally up to the
right. Cut with the area of the blade between 3 o’clock and
5 o’clock so that the direction of rotation of the blade
pushes the bottom of the tree to the left.
•
•
Clear a strip around 75 m long. Move your fuel can as
work progresses.
On sloping ground you should work along the slope. It is
much easier to work along a slope than it is to work up and
down it.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
•
To fell a tree forwards, the bottom of the tree should be
pulled backwards. Pull the blade backwards with a quick,
firm movement.
and cut from the centre of the group. If it is still difficult to
gain access, cut the stems high up and let them fall. This
will reduce the risk of jamming.
•
Large stems must be cut from two sides. First determine
which direction the stem will fall. Make the first cut on the
felling side. Then finish cutting the stem from the other
side. Adjust the cutting pressure to match the size of the
stem and the hardness of the wood. Small stems require
more pressure, while large stems require less pressure.
Grass clearing using a grass blade
•
Grass blades and grass cutters must not be used on
woody stems.
•
•
A grass blade is used for all types of tall or coarse grass.
The grass is cut down with a sideways, swinging
movement, where the movement from right-to-left is the
clearing stroke and the movement from left-to-right is the
return stroke. Let the left-hand side of the blade (between
8 and 12 o’clock) do the cutting.
•
•
If the stems are tightly packed, adapt your walking pace to
suit.
If the blade jams in a stem, never jerk the machine free. If
you do this the blade, bevel gear, shaft or handlebar may
be damaged. Release the handles, grip the shaft with
both hands and gently pull the machine free.
•
•
If the blade is angled to the left when clearing grass, the
grass will collect in a line, which makes it easier to collect,
e.g. by raking.
Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly
again.
Brush cutting with a saw blade
•
•
Let the support cup rest lightly against the ground. It is
used to protect the blade from hitting the ground.
•
Thin stems and brush are mown down. Work with a
sawing movement, swinging sideways.
Reduce the risk of material wrapping around the blade by
following these instructions:
•
•
Try to cut several stems in a single sawing movement.
1
2
Always work at full throttle.
With groups of hardwood stems, first clear around the
group. Start by cutting the stems high up around the
outside of the group to avoid jamming.Then cut the stems
to the required height. Now try to reach in with the blade
Avoid the previously cut material during the return
stroke.
•
Stop the engine, unclip the harness and place the
machine on the ground before you start to collect the cut
material.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Sweeping
Grass trimming with a trimmer head
•
The fan effect of the rotating cord can be used for quick
and easy clearing up. Hold the cord parallel to and above
the area to be swept and move the tool to and fro.
Trimming
•
Hold the trimmer head just above the ground at an angle.
It is the end of the cord that does the work. Let the cord
work at its own pace. Never press the cord into the area
to be cut.
•
When cutting and sweeping you should use full throttle to
obtain the best results.
•
•
The cord can easily remove grass and weeds up against
walls, fences, trees and borders, however it can also
damage sensitive bark on trees and bushes, and damage
fence posts.
Reduce the risk of damaging plants by shortening the
cord to 10-12 cm and reducing the engine speed.
Clearing
•
The clearing technique removes all unwanted vegetation.
Keep the trimmer head just above the ground and tilt it.Let
the end of the cord strike the ground around trees, posts,
statues and the like. CAUTION! This technique increases
the wear on the cord.
•
•
The cord wears quicker and must be fed forward more
often when working against stones, brick, concrete, metal
fences, etc., than when coming into contact with trees and
wooden fences.
When trimming and clearing you should use less than full
throttle so that the cord lasts longer and to reduce the
wear on the trimmer head.
Cutting
•
The trimmer is ideal for cutting grass that is difficult to
reach using a normal lawn mower. Keep the cord parallel
to the ground when cutting. Avoid pressing the trimmer
head against the ground as this can ruin the lawn and
damage the tool.
•
Do not allow the trimmer head to constantly come into
contact with the ground during normal cutting. Constant
contact of this type can cause damage and wear to the
trimmer head.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Basic setting
Carburetor
•
The basic carburetor settings are adjusted during testing
at the factory. The basic setting is richer than the optimal
setting and should be maintained for the first few hours the
machine is in use. The carburettor should then be finely
adjusted. Fine adjustment should be carried out by a
skilled technician.
Your Jonsered product has been designed and manufactured
to specifications that reduce harmful exhaust fumes. The
engine will be run in after it has used 8-10 tanks of fuel. To
ensure that the engine runs at peak performance and
produces as little harmful exhaust fumes as possible after the
running-in period, ask your dealer/service workshop (which
has a rev counter for this purpose) to adjust your carburettor.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come loose
and cause personal injury.
Rec. idle speed 2700 rpm
!
Recommended max. speed: See theTechnical data section.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
Function
!
•
The carburetor governs the engine’s speed via the throttle
control. Air and fuel are mixed in the carburetor. The air/
fuel mixture is adjustable. Correct adjustment is essential
to get the best performance from the machine.
Fine adjustment
•
When the machine has been ”run-in” the carburetor
should be finely adjusted. The fine adjustment should
be carried out by a qualified person. First adjust the L-
jet, then the idling screw T and then the H-jet.
•
•
The setting of the carburetor means that the engine is
adapted to local conditions, for example, the climate,
altitude, fuel and the type of 2-stroke oil.
The carburetor has three adjustment controls:
L = Low speed jet
Conditions
•
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted. If you adjust
the carburettor when the air filter is dirty it will result in a
leaner mixture when the filter is finally cleaned. This can
lead to serious engine damage.
H = High speed jet
T = Idle adjustment screw
•
•
•
Carefully turn both jets, L and H, so that they are midway
between fully screwed in and fully screwed out.
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
•
•
The L and H-jets are used to adjust the supply of fuel to
match the rate that air is admitted, which is controlled with
the throttle. If they are screwed clockwise the air/fuel ratio
becomes leaner (less fuel) and if they are turned anti-
clockwise the ratio becomes richer (more fuel). A lean
mixture gives a higher engine speed and a rich mixture
gives a lower engine speed.
Low speed jet L
•
Try to find the highest idling speed, turning the low speed
needle L clockwise respectively counter-clockwise.When
the highest speed has been found, turn the low speed
needle L 1/4 turn counter-clockwise.
The T-screw regulates the throttle setting at idle speed. If
the T-screw is turned clockwise this gives a higher idle
speed; turning it anti-clockwise gives a lower idle speed.
+ 1/4
L
CAUTION! If the cutting attachment rotates when the engine
is idling the idle adjustment screw T should be turned anti-
clockwise until the cutting attachment stops.
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Fine adjustment of the idle speedT
Correctly adjusted carburetor
Adjust the idle speed using the idle adjustment screw T, if it is
necessary to readjust. First turn the idle adjustment screw T
clockwise until the cutting attachment starts to rotate. Then
turn the screw anticlockwise until the cutting attachment
stops. The idle speed is correctly adjusted when the engine
will run smoothly in every position.The idle speed should also
be well below the speed at which the cutting attachment starts
to rotate.
When the carburetor is correctly adjusted the machine will
accelerate without hesitation and burble a little at maximum
speed. It is also important that the cutting attachment does
not rotate at idle. If the low speed jet L is set too lean it may
cause starting difficulties and poor acceleration.
If the high speed jet H is set too lean it will result in less power,
less performance, poor acceleration and/or damage to the
engine.
If both the L and H jets are set too rich it will results in
acceleration problems or too low a working speed.
Adjusting the start throttle speed
The correct start throttle speed is set by means of an adjuster
on the rear of the handle next to the cable. Use this screw (4
mm Allen screw) to increase or decrease the start throttle
speed.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
High speed jet H
5 mm
Note that the engine should not be under load when you
adjust the high speed jet H.You should therefore remove the
cutting attachment, nut, support flange and drive disc before
adjusting the high speed jet H. The high speed jet H affects
the engine power, speed, temperature and fuel consumption.
If the high speed jet H is set too lean (screwed in too far) the
engine speed will be too high and cause engine damage. Do
not let the engine run at full speed for more than 10 seconds.
Proceed as follows:
1
2
Run the machine at idle.
Press the start throttle lock as described under the
heading Starting and stopping.
3
If the start throttle speed is too low (below 4000 rpm), turn
the adjuster screw A clockwise until the cutting
attachment starts to rotate. Then turn A clockwise a
further 1/2 turn.
Apply full throttle and turn the high speed jet H very slowly
clockwise until the engine slows down. Then turn the high
speed jet H very slowly anticlockwise until the engine starts to
run unevenly. Now turn the high speed jet H slowly clockwise
a little way until the engine runs smoothly.
4
If the start throttle speed is too high, turn the adjuster
screw A anticlockwise until the cutting attachment stops.
Then turn adjuster screw A clockwise a further 1/2 turn.
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until it
has been correctly adjusted or repaired.
!
The high speed jet H is adjusted correctly when the machine
burbles a little. If the machine races then the setting is too
lean. If the engine produces a lot of smoke and burbles a lot
then the setting is too rich.
H
CAUTION! For optimum adjustment of the carburettor,
contact a qualified dealer/service workshop that has a
revolution counter at their disposal.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Muffler
Cooling system
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether your
machine is fitted with a catalytic converter.
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The cooling system consists of:
The muffler is designed to reduce the noise level and to direct
the exhaust gases away from the operator. The exhaust
gases are hot and can contain sparks, which may cause fire
if directed against dry and combustible material.
1
2
3
4
Air intake on the starter.
Fins on the flywheel.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
4
3
2
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you should
clean the screen at least once a week.This is best done with
a wire brush.
1
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
On mufflers without a catalytic converter the screen should be
cleaned weekly, or replaced if necessary. On mufflers fitted
with a catalytic converter the screen should be checked, and
if necessary cleaned, monthly. If the screen is damaged it
should be replaced.
Bevel gear
The bevel gear is filled with the right amount of grease at the
factory. However, before using the machine you should check
that the bevel gear is filled 3/4 full with grease. Use
JONSERED special grease.
If the screen is frequently blocked, this can be a sign that the
performance of the catalytic converter is impaired. Contact
your dealer to inspect the muffler. A blocked screen will cause
the machine to overheat and result in damage to the cylinder
and piston.
The grease in the bevel gear does not normally need to be
changed except if repairs are carried out.
CAUTION! Never use a machine with a defective muffler.
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.This
also applies at idle speed. Contact can result
in burns to the skin. Remember the risk of
fire!
!
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Air filter
Spark plug
The air filter must be regularly cleaned to remove dust and dirt
in order to avoid:
The spark plug condition is influenced by:
•
•
Incorrect carburetor adjustment.
•
•
•
•
•
Carburettor malfunctions
Starting problems
An incorrect fuel mixture (too much or incorrect type of
oil).
Loss of engine power
•
A dirty air filter.
Unnecessary wear to engine parts
Excessive fuel consumption.
These factors cause deposits on the spark plug electrodes,
which may result in operating problems and starting
difficulties.
Clean the filter every 25 hours, or more regularly if conditions
are exceptionally dusty.
If the machine is low on power, difficult to start or runs poorly
at idle speed: always check the spark plug first before taking
any further action. If the spark plug is dirty, clean it and check
that the electrode gap is 0.020 inch (0.5 mm).The spark plug
should be replaced after about a month in operation or earlier
if necessary.
Cleaning the air filter
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Ensure that the filter is dry before
refitting it.
CAUTION! Always use the recommended spark plug type!
Use of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.
An air filter that has been in use for a long time cannot be
cleaned completely.The filter must therefore be replaced with
a new one at regular intervals. A damaged air filter must
always be replaced.
IMPORTANT! Use only JONSERED replacement parts.
Use of other brands of replacement parts can cause
damage to your unit or injury to the operator or others.Your
warranty does not cover damage or liability caused by the
use of accessories and/or attachments not specifically
recommended by JONSERED.
If the machine is used in dusty conditions the air filter should
be soaked in oil.See instructions under the heading Oiling the
air filter.
Oiling the air filter
Always use special filter oil. Filter oil contains a solvent to
make it spread evenly through the filter.You should therefore
avoid skin contact.
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour off
the excess before fitting the filter to the machine. Never use
common engine oil. This would drain through the filter quite
quickly and collect in the bottom.
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive
work must be carried out by an authorised service workshop.
Daily
maintenance
Weekly
maintenance
Monthly
maintenance
Maintenance
Clean the outside of the machine.
X
X
Check that the harness is not damaged.
Make sure the throttle trigger lock and the throttle function correctly from a
safety point of view.
X
X
X
Check that the stop switch works correctly.
Check that the handle and handlebar are undamaged and secured
correctly.
Check that the cutting attachment does not rotate at idle.
Clean the air filter. Replace if necessary.
X
X
Check that the guard is undamaged and not cracked. Replace the guard if
it has been exposed to impact or is cracked.
X
X
X
Check that the blade is correctly centred, is sharp, and is not cracked. An
off-centre blade will cause vibration that could result in damage to the
machine.
Check that the trimmer head is undamaged and not cracked. Replace the
trimmer head if necessary.
Check that the locking nut of the cutting equipment is tighten correctly.
Check that nuts and screws are tight.
X
X
X
Check that there are no fuel leaks from the engine, tank or fuel lines.
Check that the transport guard for the blade is intact and that it can be
secured correctly.
X
Check the starter and starter cord.
X
X
Check that the vibration damping elements are not damaged.
Clean the outside of the spark plug. Remove it and check the electrode
gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that
the spark plug is fitted with a suppressor.
X
Clean the machines cooling system.
X
X
X
X
Clean or replace the spark arrestor screen on the muffler (only applies to
mufflers without a catalytic converter).
Clean the outside of the carburettor and the space around it.
Check that the bevel gear is filled three-quarters full with lubricant. Fill if
necessary using special grease.
Check the fuel filter from contamination and the fuel hose from cracks or
other defects. Replace if necessary.
X
X
X
Check all cables and connections.
Check the clutch, clutch springs and the clutch drum for wear. Replace if
necessary by an autorized service workshop.
Replace the spark plug. Check that the spark plug is fitted with a
suppressor.
X
X
Check and clean the spark arrestor screen on the muffler (only applies to
mufflers fitted with a catalytic converter).
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
Technical data
BC 2125
Engine
3
Cylinder displacement, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
1,50/24,5
1,26/32
1,06/27
2700
Idle speed, rpm
Recommended max. fast idle speed, rpm
Speed of output shaft, rpm
11000-11700
8014
Max. engine output, acc. to ISO 8893, kW/ rpm
Catalytic converter muffler
Speed-regulated ignition system
Ignition system
0,9/9000
No
Yes
Manufacturer/type of ignition system
Spark plug
WalbroMB/SEM AM49
NGK BPMR 7A/ Champion RCJ 7Y
0,02/0,5
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer/type of carburetor
Fuel tank capacity, US pint/litre
Weight
Zama C1Q
1,06/0,5
Weight without fuel, cutting attachment and guard, Lbs/kg 9,9/4,5
Sound levels
(see note 1)
Equivalent sound pressure level at the user′s ear, measured
91/97
according to ANSI B175.3-1997, dB(A), min/max:
Vibration levels
Vibration levels at handles, measured according to
2
ANSI B175.3-1997, m/s
At idle, left/right handles, min.:
1,1/1,0
1,6/1,9
1,5/1,3
5,5/3,5
At idle, left/right handles, max.:
At max. speed, left/right handles, min.:
At max. speed, left/right handles, max.:
Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various
working conditions with the following time distribution: 1/2 idle and 1/2 max. speed.
NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting
equipment fitted. The table indicates the highest and lowest values.
Approved accessories
Centre hole in blades/cutters, Ø 25,4 mm
Arbor shaft thread M10
Saw blade
Type
Cutting attachment guard, Art. no.
Opti S 200-26 (Ø 200 26 teeth)
Grass 255-4 1" (Ø 255 4-teeth)
Grass 255-8 1" (Ø 255 8-teeth)
Tap-N-Go Pro
537 29 95-01
503 93 42-04
Grass blade/grass cutter
503 93 42-04
503 93 42-04 / 503 97 71-03
503 93 42-04 / 503 97 71-03
503 93 42-04 / 503 97 71-03
503 93 42-04 / 503 97 71-03
503 93 42-04 / 503 97 71-03
503 93 42-04 / 503 97 71-03
503 93 42-04
Trimmy H II
Tap-N-Go 35
Trimmer head
Plastic blades
S35
Auto32
Tap-N-Go 25 (L)
Polytrim
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
your warranty rights and responsibilities, you should contact
your nearest authorized servicing dealer or call Husqvarna
Forest & Garden at 1-800-487-5963.
YOUR WARRANTY RIGHTS AND
OBLIGATIONS
WARRANTY PERIOD Any warranted part which is not
scheduled for replacement as required maintenance, or
which is scheduled only for regular inspection to the effect of
“repair or replace as necessary” shall be warranted for 2
years.Any warranted part which is scheduled for replacement
as required maintenance shall be warranted for the period of
time up to the first scheduled replacement point for that part.
The EPA (The US Environmental Protection Agency),
Environment Canada and Husqvarna Forest & Garden are
pleased to explain the emissions control system warranty on
your 2001 and later small nonroad engine. In U.S. and
Canada, new small nonroad engines must be designed, built
and equipped to meet the federal stringent anti-smog
standards. Husqvarna Forest & Garden must warrant the
emission control system on your small nonroad engine for the
period of time listed below provided there has been no abuse,
neglect or improper maintenance of your unit.Your emission
control system includes Parts such as the carburetor and the
ignition system. Where a warrantable condition exists,
Husqvarna Forest & Garden will repair your small nonroad
engine at no cost to you. Expenses covered under warranty
include diagnosis, parts and labor.
DIAGNOSIS The owner shall not be charged for diagnostic
labor which leads to the determination that a warranted part
is defective, if the diagnostic work is performed at an
approved Husqvarna Forest & Garden servicing dealer.
CONSEQUENTIAL DAMAGES Husqvarna Forest & Garden
may be liable for damages to other engine components
caused by the failure of a warranted part still under warranty.
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
′
MANUFACTURER S WARRANTY
COVERAGE
The 2001 and later small nonroad engines are warranted for
two years. If any emission related part on you engine (as
listed above) is defective, the part will be repaired or replaced
by Husqvarna Forest & Garden.
ADD -ON OR MODIFIED PARTS
The use of add-on or modified parts can be grounds for
disallowing a warranty claim. Husqvarna Forest & Garden is
not liable to cover failures of warranted parts caused by the
use of add-on or modified parts.
′
OWNER SWARRANTY RESPONSIBILITIES
As the small nonroad engine owner, you are responsible for
the performance of the required maintenance listed in your
Operator′s Manual. Husqvarna Forest & Garden
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and
responsibilities, you should contact your nearest authorized
servicing dealer or call Husqvarna Forest & Garden at 1-800-
487-5963.
recommends that you retain all receipts covering
maintenance on your small nonroad engine, but Husqvarna
Forest & Garden cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all
scheduled maintenance. As the small nonroad engine owner,
you should, however, be aware that Husqvarna Forest &
Garden may deny you warranty coverage if your small
nonroad engine or a part of it has failed due to abuse, neglect,
improper maintenance, unapproved modifications or the use
of parts not made or approved by the original equipment
manufacturer.You are responsible for presenting your small
nonroad engine to a Husqvarna Forest & Garden authorized
servicing dealer as soon as a problem exists. The warranty
repairs should be completed in a reasonable amount of time,
not to exceed 30 days. If you have any questions regarding
your warranty rights and responsibilities, you should contact
your nearest authorized servicing dealer or call Husqvarna
Forest & Garden at 1-800-487-5963.
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs shall be provided at all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement part
used in the performance of any warranty maintenance or
repairs on emission-related parts, will be provided without
charge to the owner if the part is under warranty.
EMISSION CONTROL WARRANTY PARTS
LIST
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date small nonroad engine
is delivered.
1
2
3
4
Carburetor and internal parts
Intake pipe, airfilter holder and carburetor bolts.
Airfilter and fuelfilter covered up to maintenance schedule.
Ignition System
LENGTH OF COVERAGE
1
2
Spark Plug, covered up to maintenance schedule
Ignition Module
Husqvarna Forest & Garden warrants to the initial owner and
each subsequent purchaser that the engine is free from
defects in materials and workmanship which cause the failure
of a warranted part for a period of two years.
5
Muffler with catalytic converter
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required
maintenance, as defined in the operator’s manual.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or
replacement of any warranted part will be performed at no
charge to the owner at an approved Husqvarna Forest &
Garden servicing dealer. If you have any questions regarding
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap-N-Go Pro
1
2
3
4
7,5 m
25'
15 cm
6"
~ 3,7 m
12'
5
6
9
7
8
15 cm
6"
11
10
12
1.)
2.)
15 cm
6"
“Click”
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimmy H II
1
2
3
4
15 cm
6"
7,5 m
25'
~ 3,7 m
12'
7
5
6
8
9
2
1
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap-N-Go 35
1
2
3
8,5 m
28'
10 cm
4"
4,3 m
14'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
3
8,5 m
28'
10 cm
4"
4,2 m
14'
4
5
7
6
8
"Clic"
10
11
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
S35
1
2
4,25 m
14'
4,25 m
14'
4
3
5
15 cm
6"
B
A
15 cm
6"
Download from Www.Somanuals.com. All Manuals Search And Download.
Tap-N-Go 25
1
2
3
6,0 m
18'
10 cm
4"
3,05 m
9'
4
5
7
6
8
"Clic"
15 cm
6"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto 32
1
2
3
6
4
5
4,0 m
13'
15 cm
~2,0 m
6,5
6
"
'
15 cm
6
8
7
"
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Poly Trim
1
2
<20mm
B
A
3
4
5
>20mm
7
6
6 Nm
!
8
X 10
´®z+R:e¶5k¨
´®z+R:e¶5k¨
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1150266-95
´®z+R:e¶5k¨
´®z+R:e¶5k¨
2006-10-10
Download from Www.Somanuals.com. All Manuals Search And Download.
|
