John Deere Spreader SS1023B User Manual
O P E R A T O R ’ S M A N U A L  
FERTILIZER SPREADERS  
SS1023B  
SS1036B  
SS1067B  
SS2036B  
SS2067B  
Manual 5BP960376B  
Date 05/19/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INDEX  
4
4
1 - GENERAL INFORMATION  
1.01 - General  
1.02 - Model and Serial Number ID  
4
1.03 - Assembly Instructions for Model SS1023B  
1.04 - Assembly Instructions for Models SS1036B & SS2036B  
1.05 - Assembly Instructions for Models SS1067B & SS2067B  
2 - SAFETY PRECAUTIONS  
2.01 - Preparation  
5
6
8
11  
11  
11  
12  
14  
14  
15  
15  
16  
17  
17  
20  
21  
21  
22  
22  
23  
26  
26  
26  
27  
28  
31  
2.02 - Starting and Stopping  
2.03 - Messages and Signs  
3 - OPERATION  
3.01 - Operational Safety  
3.02 - Set Up  
3.03 - Pre-Operational Check  
3.04 - Attaching to the Tractor  
3.05 - Start Up  
3.06 - Operating Techniques  
3.07 - Uneven Terrain  
4 - MAINTENANCE  
4.01 - Maintenance Safety  
4.02 - Service  
4.03 - Driveline  
4.04 - Transport  
5 - REPAIR PROCEDURES  
5.01 - Suggested Spare Parts  
5.02 - Storage  
6 - TROUBLESHOOTING  
7 - PRE-DELIVERY CHECKLIST  
PARTS MANUAL  
INDEX  
3
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
1 - GENERAL INFORMATION  
Thank you and congratulations for having chosen our implement. Your new fertilizer spreader is a  
technologically advanced machine constructed of high quality sturdy components that will fulfill your  
working expectations. Read this manual carefully. It will instruct you on how to operate and service  
your fertilizer spreader safely and correctly. Failure to do so could result in personal injury and/or  
equipment damage.  
1.01 - General  
The implement described in this manual is to be used with tractors with PTO at 540 rpm and  
clockwise rotation.  
CAUTION: Always ensure that the coupling of the implement with the tractor is done at the  
same PTO speed and direction of rotation. Do not operate this implement at a PTO speed or  
direction of rotation other than that shown on the implement. Serious damage can occur to  
the machine and/or the operator.  
CAUTION: Unless otherwise specified, all hardware is metric. Use only metric tools on metric  
hardware. Other tools that do not fit properly can slip and cause injury.  
CAUTION: Right hand and left hand sides of the implement are determined by facing in the  
direction the implement will travel when going forward (see fig. 6).  
Warranty coverage is provided by John Deere according to the terms of the Agricultural/Commercial  
& Consumer Equipment Warranty Statement. Carefully read the warranty statement on the back of  
your original purchase order for details on coverage and limitations of this warranty.  
Your Authorized Company Dealer has genuine parts in stock. Only these approved replacement parts  
should be used.  
1.02 - Model and Serial Number ID  
Attached to the hopper is an ID plate showing the model and the serial number. Record your  
implement model and serial number in the space provided below. Your dealer needs this information  
to give you prompt, efficient service when you order parts.  
GENERAL INFORMATION  
4
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
1.03 - Assembly Instructions for Model SS1023B  
CAUTION: Stand clear of bands when cutting as they could be under sufficient tension to  
cause them to fly loose. Take care in removing bands and wire. They often have extremely  
sharp edges and cut very easily.  
NOTE: Assembly will be easier if all parts are loosely assembled before tightening the hardware. All  
hardware needed for assembly will be found in the hardware bag or on the machine.  
Each unit is shipped with a hardware bag that consists of the following:  
Description  
Model SS1023B Qty.  
Spreader disc (#11, fig. 2)  
Mobile shutter (#10, fig. 2)  
Stirrer (#8, fig. 2)  
Guard (#4, fig. 2)  
Flow control assembly (#5, fig. 2)  
Driveline  
1
1
1
1
1
1
Hardware bag contains the following:  
Bushing cat.0/1 for tractor arms (5BP0014710); serial #XF...287132 & below only  
Threaded bushing (5BP501622B)  
Bolt CR M08-1.25x25 C4.6 Z (5BP501663B)  
Bolt HH M08-1.25x16 C8.8 Z F (5BP0046454)  
Nut HH M30-2.00 C6 Z TN (5BP501651B)  
Nut HH M08-1.25 C6 Z TK (5BP0001806)  
Washer flat Ø8 (5BP0015230)  
2
1
3
2
1
8
4
3
1
Washer fender Ø8 (5BP0014514)  
Hairpin cotter Ø5 (5BP0041291)  
To assemble the spreader do the following:  
1. Attach spreader disc (see #11, fig. 2) to output shaft of gearbox securing it with the hairpin cotter  
(see #27, fig. 2).  
2. Install guard (see #4, fig. 2) with scale label facing up to the brackets on the spreader frame.  
Attach it to the frame using two M8x16 bolts (see #22, fig. 2), four Ø8 flat washers (see #19, fig.  
2) and two M8 nuts (see #21, fig. 2).  
3. Insert threaded bushing (see #9, fig. 2) through hopper bottom (see #3, fig. 2). Attach mobile  
shutter (see #10, fig. 2) to threaded bushing and secure with nut (see #26, fig. 2).  
4. Slide hopper and onto the output shaft of the gearbox. Secure hopper to frame using three M8x25  
carriage bolts (see #18, fig. 2), three Ø8 fender washers (see #20, fig. 2), and six M8 hex nuts  
(see #21, fig. 2).  
5. Install flow control assembly (see #5, fig. 2) into slot in mobile shutter at the bottom of the hopper.  
6. Secure location of the shutter lever by tightening the two knobs (see #6, fig. 2).  
7. Install the stirrer (see #8, fig. 2) using M8x35 hex bolt (see #24, fig. 2), two Ø8 flat washers (see  
#19, fig. 2), and one M8 elastic stop nut (see #25, fig. 2) that are already bolted to the stirrer.  
8. Tighten all hardware.  
9. Install driveline and ensure it has at least 2” from bottoming out in its shortest working position and  
has the minimum 6” overlap in its longest working position. Refer to Section 4.031 of this manual,  
if it is determined that the driveline is too long and needs to be shortened. Contact your local  
dealer if it is determined that the driveline is too short for your tractor.  
1
See Section 4.03 - Driveline, for instructions on how to determine correct driveline length and procedures for  
shortening the driveline.  
GENERAL INFORMATION  
5
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
Fig. 2 - Model SS1023 assembly.  
1.04 - Assembly Instructions for Models SS1036B & SS2036B  
Each unit is shipped with a hardware bag that consists of the following:  
Description  
Model SS1036B Qty.  
Model SS2036B Qty.  
Spreader disc (#21, fig. 3)  
Shutter assembly  
Protection (#5, fig. 3)  
Lever (#16, fig. 3)  
Scaled rod assembly (#18, fig. 3)  
Stationary stirrer (#20, fig. 3)  
Protection (#4, fig. 3)  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Driveline  
Hardware bag contains the following:  
Attachment plate (5BP0014338) (#6, fig. 3)  
Attachment plate (5BP0014635) (#6, fig. 3)  
Bushing cat.0/1 for tractor arms (5BP0014710)  
Bolt CR M08-1.25x20 C4.6 Z (5BP0084289)  
Bolt CR M08-1.25x25 C4.6 Z (5BP501663B)  
Bolt CR M08-1.25x35 C4.6 Z (5BP0014619)  
Bolt HH M08-1.25x16 C8.8 Z F (5BP0046454)  
Bolt HH M08-1.25x20 C8.8 Z F (5BP0015012)  
Nut HH M08-1.25 C6 Z MD (5BP0046545)  
Nut HH M08-1.25 C6 Z TK (5BP0001806)  
Washer lock Ø8 (5BP0003144)  
Washer flat Ø8 (5BP0015230)  
Washer fender Ø8 (5BP0014514)  
Washer fender Ø10 (5BP0030157)  
Hairpin cotter Ø5 (5BP0041291)  
1
-
2
3
3
-
1
2
6
6
3
7
3
2
1
-
1
2
2
-
3
1
2
5
6
2
6
3
2
1
GENERAL INFORMATION  
6
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
CAUTION: Stand clear of bands when cutting as they could be under sufficient tension to  
cause them to fly loose. Take care in removing bands and wire. They often have extremely  
sharp edges and cut very easily.  
NOTE: Assembly will be easier if all parts are loosely assembled before tightening the hardware. All  
hardware needed for assembly will be found in the hardware bag or on the machine.  
Fig. 3 - Model SS1036B & SS2036B assembly.  
To assemble the spreader do the following:  
1. Attach spreader disc (see #21, fig. 3) to the output shaft of the gearbox using hairpin cotter (see  
#45, fig. 3).  
2. Locate scaled rod assembly (see #18, fig. 3) in hardware bag. Install scaled rod to main frame  
using M8x30 bolt (see #29, fig. 3), Ø8 lock washer (see #40, fig. 3), M8 hex nut (see #34, fig. 3)  
that are already installed on the scaled rod assembly.  
3. Install protection (see #4, fig. 3) onto spreader frame using two M8x20 hex bolts (see #26, fig. 3),  
four Ø8 flat washers (see #38, fig. 3), and two M8 hex nuts (see #34, fig. 3).  
4. Slide hopper onto the output shaft of the gearbox. Secure hopper to frame using three M8x25  
carriage bolts on model SS1036 or M8x35 on model SS2036 (see #25, fig. 3), three Ø8 fender  
washers (see #39, fig. 3), and six M8 hex nuts (see #33, fig. 3).  
GENERAL INFORMATION  
7
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
5. Install the stationary stirrer (see #20, fig. 3) using M8x45 hex bolt (see #31, fig. 3), two Ø8 flat  
washers (see #38, fig. 3), and one M8 elastic stop nut (see #36, fig. 3) that are already bolted to  
the stirrer.  
6. Install protection (see #5, fig. 3) using two M8x20 carriage bolts (see #28, fig. 3), two Ø10 fender  
washers (see #42, fig. 3), two Ø8 lock washers (see #40, fig. 3) and secure with two M8 hex nuts  
(see #34, fig. 3). Install attachment plate (see #6, fig. 3) on protection using M8x16 hex bolt (see  
#27, fig. 3), two Ø8 flat washers (see #38, fig. 3) and secure with M8 hex nut (see #34, fig. 3),  
then install it to the hopper using M8x20 carriage bolt on model SS1036 or M8x25 on model  
SS2036 (see #28, fig. 3), on model SS2036 use bolt already installed on hopper, and secure with  
Ø8 flat washer (see #38, fig. 3), Ø8 lock washer (see #40, fig. 3) and a M8 hex bolt (see #34, fig.  
3).  
7. Install shutter assembly found in the hardware bag by sliding shutters (see #7 & #8, fig. 3) into the  
slots at bottom of the hopper.  
8. Assemble shutter guide plate (see #11, fig. 3) to lever bracket (see #12, fig. 3), which is already  
installed on the frame using M8x30 hex bolt (see #29, fig. 3), Ø8 lock washer (see #40, fig. 3),  
and M8 hex nut (see #34, fig. 3).  
9. Install lever (see #16, fig. 3) to lever bracket using one M8x20 hex bolt (see #26, fig. 3) which is  
shipped installed on the lever. Secure bolt with M8 hex nut (see #34, fig. 3).  
10.Tighten all hardware.  
11.Install driveline and ensure it has at least 2” from bottoming out in its shortest working position and  
has the minimum 6” overlap in its longest working position. Refer to Section 4.032 of this manual,  
if it is determined that the driveline is too long and needs to be shortened. Contact your local  
dealer if it is determined that the driveline is too short for your tractor.  
1.05 - Assembly Instructions for Models SS1067B & SS2067B  
Each unit is shipped with a hardware bag that consists of the following:  
Description  
Model SS1067B Qty.  
Model SS2067B Qty.  
Lever (#14, fig. 4)  
Hitch lever (#15, fig. 4)  
Scaled rod (#17, fig. 4)  
Shutter assembly (#9, fig. 4)  
Protection (#4, fig. 4)  
Protection (#1, fig. 5)  
Spreader wings (#20, fig. 4)  
Stationary stirrer (#21, fig. 4)  
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
4
1
1
Driveline  
Hardware bag contains the following:  
Attachment plate (5BP0014338) (#2, fig. 5)  
Attachment plate (5BP0014339) (#2, fig. 5)  
Bolt CR M12-1.75x30 C4.6 Z (5BP0051073)  
Bolt CR M12-1.75x40 C8.8 Z (5BP0044115)  
Bolt CR M08-1.25x20 C4.6 Z (5BP0084289)  
Bolt HH M08-1.25x16 C8.8 Z F (5BP0046454)  
Bolt HH M08-1.25x20 C8.8 Z F (5BP0015012)  
Bolt HH M06-1.00x16 C8.8 Z F (5BP0036319)  
Nut HH M12-1.75 C6 Z MD (5BP0001106)  
Nut HH M08-1.25 C6 Z MD (5BP0046545)  
Nut HH M06-1.00 C6 Z TK (5BP501603B)  
Washer lock Ø6 (5BP0046536)  
Washer lock Ø8 (5BP0003144)  
Washer flat Ø8 (5BP0015230)  
Washer flat Ø14 (5BP0091435)  
1
-
3
-
-
1
-
3
-
3
2
8
6
5
8
8
-
1
3
2
8
6
6
8
8
1
11  
3
10  
3
2
See Section 4.03 - Driveline, for instructions on how to determine correct driveline length and procedures for  
shortening the driveline.  
GENERAL INFORMATION  
8
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
CAUTION: Stand clear of bands when cutting as they could be under sufficient tension to  
cause them to fly loose. Take care in removing bands and wire. They often have extremely  
sharp edges and cut very easily.  
NOTE: Assembly will be easier if all parts are loosely assembled before tightening the hardware. All  
hardware needed for assembly will be found in the hardware bag or on the machine.  
Fig. 4 - Models SS1067B & SS2067B assembly.  
To assemble the spreader do the following:  
1. Attach four spreader wings (see #20, fig. 4) to the spreader disc (see #19, fig. 4) with eight  
M6x16 hex bolts (see #36, fig. 4), Ø6 lock washers (see #37, fig. 4) and M6 hex nuts (see #38,  
fig. 4).  
2. Locate scaled rod assembly (see #17, fig. 4) in hardware bag. Install scaled rod to main frame  
using M8x30 hex bolt (see #29, fig. 4), Ø8 lock washer (see #30, fig. 4) and M8 hex nut (see #28,  
fig. 4) that are already installed on the scaled rod assembly.  
3. Install protection (see #4, fig. 4) on spreader frame using two M8x20 hex bolts (see #26, fig. 4),  
two Ø8 flat washers (see #27, fig. 4) and two M8 hex nuts (see #28, fig. 4).  
4. Slide hopper (see #3, fig. 4) onto the output shaft of the gearbox.  
GENERAL INFORMATION  
9
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
5. Secure hopper to frame using three M12x30 carriage bolts on model SS1067B or M12x40 on  
model SS2067B (see #23, fig. 4), three Ø14 flat washers (see #24, fig. 4), and six M12 hex nuts  
(see #25 fig. 4).  
6. Install stationary stirrer (see #21, fig. 4) using M8x45 bolt (see #39, fig. 4), two Ø8 flat washers  
(see #27, fig. 4), and M8 elastic stop nut (see #40, fig. 4) that are already bolted to the stirrer.  
7. This step only applies to units with serial #BC…304870 and above. Install spreader disc  
shield (see #1, fig. 5) using three M8x16 hex bolts (see #3, fig. 5), six Ø8 flat washers (see #4,  
fig. 5), one Ø8 lock washer (see #5, fig. 5), and three M8 hex nuts (see #6, fig. 5). Install M8x20  
carriage bolt (see #7, fig. 5) on SS1067B or M8x25 on SS2067B through hopper and into  
attachment plate (see #2, fig. 5). On model SS2067B use bolt already installed on hopper.  
8. Install shutter assembly, found in hardware bag, by sliding shutters (see #5 & #6, fig. 4) into the  
slots at the bottom of the hopper.  
9. Assemble shutter guide plate (see #9, fig. 4) to lever bracket (see #10, fig. 4), which is already  
installed on the frame, using M8x30 hex bolt (see #29, fig. 4), Ø8 lock washer (see #30, fig. 4),  
and M8 hex nut (see #28, fig. 4).  
10.This step only applies to units with serial #BC…304870 and above. Attach hitch lever (see  
#15, fig. 4) to lever bracket (see #10, fig. 4) by loosening M8x20 hex bolt (see #26, fig. 4) which  
is shipped already installed onto hitch lever. Secure bolt with M8 hex nut (see #28, fig. 4).  
11.Install lever (see #14, fig. 4) to hitch lever using M8x20 hex bolt (see #26, fig. 4) and M8 hex nut  
(see #28, fig. 4) which is shipped already installed on the lever.  
12.Tighten all hardware.  
13.Install driveline and ensure it has at least 2” from bottoming out in its shortest working position and  
has the minimum 6” overlap in its longest working position. Refer to Section 4.033 of this manual,  
if it is determined that the driveline is too long and needs to be shortened. Contact your local  
dealer if it is determined that the driveline is too short for your tractor.  
Fig. 5 - Models SS1067B & SS2067B shield assembly.  
(serial #BC...304870 and above)  
3
See Section 4.03 - Driveline, for instructions on how to determine correct driveline length and procedures for  
shortening the driveline.  
GENERAL INFORMATION  
10  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
2 - SAFETY PRECAUTIONS  
Safety is the primary concern in the design and manufacture of our products. Unfortunately our efforts  
to provide safe equipment can be wiped out by a single careless act of an operator.  
In addition to the design and configuration of equipment, hazard control and accident prevention are  
dependent upon the awareness, concern, prudence and proper training of personnel involved in the  
operation, transport, maintenance and storage of equipment.  
It is the operator’s responsibility to read and understand all safety and operating instructions in the  
manual and to follow these.  
Allow only properly trained personnel to operate the fertilizer spreader. Working with unfamiliar  
equipment can lead to careless injuries. Read this manual, and the manual for your tractor, before  
assembly or operation, to acquaint yourself with the machines. It is the spreader owner’s  
responsibility, if this machine is used by any person other than yourself, is loaned or rented, to make  
certain that the operator, prior to operating, reads and understands the operator’s manuals and is  
instructed in safe and proper use.  
2.01 - Preparation  
1. Before operating equipment read and understand the operator’s manual and the safety signs (see  
fig. 6).  
2. Thoroughly inspect the implement before initial operation to assure that all packaging materials,  
i.e., wires, bands, and tape have been removed.  
3. Personal protection equipment including hard hat, safety glasses, safety shoes, and gloves are  
recommended during assembly, installation, operation, adjustment, maintaining and/or repairing  
the implement.  
4. Operate the fertilizer spreader only with  
a
tractor equipped with an approved  
Roll-Over-Protective-System (ROPS). Always wear your seat belt. Serious injury or even death  
could result from falling off the tractor.  
5. Clear area of stones, branches or other debris that might be thrown, causing injury or damage.  
6. Operate only in daylight or good artificial light.  
7. Ensure fertilizer spreader is properly mounted, adjusted and in good operating condition.  
8. Ensure that all safety shielding and safety signs are properly installed and in good condition.  
9. Chemicals may cause eye, skin or breathing problems. Always wear a face mask, gloves and  
goggles when filling hopper.  
10.Before loading the fertilizer in the hopper read carefully the instructions printed on the fertilizer  
canvas bag concerning the precautions to be taken in case of toxicity or corrosivity of the product.  
Before loading switch off the engine and remove the ignition key.  
11.Load hopper with product only after the spreader has been properly attached to the tractor.  
2.02 - Starting and Stopping  
1. Be sure that no one is near the machine prior to engaging or while the machine is working.  
2. Be sure the tractor is in “Neutral” before starting engine.  
SAFETY PRECAUTIONS  
11  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
3. The operating power is supplied from tractor PTO. Refer to your tractor manual for PTO  
engagement and disengagement instructions. Always operate PTO at 540 rpm. Know how to stop  
the tractor and machine quickly in case of an emergency.  
4. When engaging PTO, the engine rpm should always be low. Once engaged and ready to start  
operating, raise PTO speed to 540 rpm and maintain throughout operation.  
5. Check the tractor master shield over the PTO stub shaft. Make sure it is in good condition and  
fastened securely to the tractor. Purchase a new shield if old shield is damaged or missing.  
6. After striking an obstacle, disengage the PTO, shut the tractor down and thoroughly inspect for  
damage before restarting.  
7. To park the vehicle safely, stop vehicle on a level surface (not on a slope), disengage PTO,  
engage the parking brake, stop the engine, remove the key, and wait for engine and all moving  
parts to stop before leaving the operator’s seat.  
8. Stay clear of rotating drivelines. Entanglement in rotating driveline can cause serious injury or  
death. Wear close fitting clothing. Stop the engine and be sure PTO driveline is stopped before  
getting near it.  
2.03 - Messages and Signs  
1. Read and adhere to all safety and operating decals on this machine (see fig. 6).  
2. Before dismounting tractor: Stop engine, set brake and remove the key of unattended equipment.  
3. Keep away from rotating parts and driveline.  
4. Keep guards and shields in place and in good condition.  
5. Do not use with bystanders in area.  
6. Allow no riders on tractor or fertilizer spreader.  
7. Allow moving parts to stop before repair.  
8. Securely support fertilizer spreader before working underneath.  
Additional warning and operating decals are available at no extra charge. Please specify model and  
serial number when ordering.  
Fig. 6 - Safety decals - driveline; replace immediately if damaged.  
outer shield  
outer tube  
SAFETY PRECAUTIONS  
12  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
Safety decals - implement; replace immediately if damaged.  
right side  
left side  
SAFETY PRECAUTIONS  
13  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
3 - OPERATION  
The fertilizer spreader is versatile and ideal for granular or powdered fertilizers, seed and sand. It may  
also be used as a salt spreader for snow or ice covered roads during winter months. Our spreaders  
are designed for tractors from 16 to 30 PTO HP with a category 1 three point hitch.  
Spreaders can be used for broadcast spreading or may be used to spread prevalently to the left or to  
the right with a simple adjustment.  
The wide range of hopper capacities and numerous spread adjustments make our fertilizer spreaders  
ideal for use on farms, athletic fields, municipalities and many other commercial or residential  
applications.  
3.01 - Operational Safety  
CAUTION: Our spreaders are designed considering safety as the most important target and  
are the safest available in today’s market. Unfortunately, human carelessness can override the  
safety features built into our machines. Injury prevention and work safety, aside from the  
features on our spreaders, are very much due to the responsible use of the equipment. It must  
always be operated prudently following with great care, the safety instructions laid out in this  
manual.  
1. The use of this equipment is subject to certain hazards which cannot be prevented by mechanical  
means or product design. All operators of this equipment must read and understand this entire  
manual, paying particular attention to safety and operating instructions, prior to using.  
2. Do not operate the tractor and spreader when you are tired, sick or when using medication.  
3. This spreader is designed for use only on tractors with 540 rpm power take off.  
4. Only properly trained people should operate this machine.  
5. Accidents are most likely to occur with machines that are loaned or rented to someone who has  
not read the operator’s manual and is not familiar with a spreader.  
6. Always stop the tractor, set brake, shut off the tractor engine, remove the ignition key, and allow  
spreader moving parts to come to a complete stop before dismounting tractor. Never leave  
equipment unattended with the tractor running.  
7. Never place hands or feet into hopper with tractor engine running or before you are sure all motion  
has stopped. Stay clear of all moving parts.  
8. Never allow any person inside the hopper for any reason. Serious injury or death can result from  
someone becoming entangled in the agitator.  
9. Do not allow riders on the spreader or tractor at any time. There is no safe place for riders.  
10.Never allow anyone within 50 yards of the spreader while the PTO is engaged. Product thrown  
from the spreader can cause serious injury or death.  
11.Before backing up, look behind carefully.  
12.Install and secure all guards and shields before starting or operating.  
13.Keep hands, feet, hair and clothing away from moving parts.  
14.Never operate tractor and spreader under trees with low hanging limbs. Operators can be  
knocked off the tractor and then run over.  
15.Stop spreader immediately upon striking an obstruction. Turn engine off, remove key, inspect and  
repair any damage before resuming operation.  
OPERATION  
14  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
16.Stay alert for holes, rocks and roots in the terrain and other hidden hazards. Keep away from  
drop-offs.  
17.Use extreme care and maintain minimum ground speed when transporting on hillside, over rough  
ground and when operating close to ditches or fences. Be careful when turning sharp corners.  
18.Reduce speed on slopes and sharp turns to minimize tipping or loss of control. Be careful when  
changing directions on slopes. Do not start or stop suddenly on slopes. Avoid operation on steep  
slopes.  
19.Inspect the entire machine periodically4. Look for loose fasteners, worn or broken parts, and leaky  
or loose fittings.  
20.Pass diagonally through sharp dips and avoid sharp drops to prevent “hanging up” tractor and  
spreader.  
21.Avoid sudden starts and stops while traveling up or downhill.  
22.Always operate down slopes; never across the face. Avoid operation on steep slopes. Slow down  
on sharp turns and slopes to prevent tipping and/or loss of control.  
23.All remote control devices (cables, ropes, rods, flexible lines, etc.) should be positioned in a way  
to prevent maneuvers which could lead to accidents or damages.  
24.Chemicals may cause eye, skin or breathing problems. Always wear a face mask, gloves and  
goggles when filling hopper.  
25.Before loading the fertilizer in the hopper read carefully the instructions printed on the fertilizer  
canvas bag concerning the precautions to be taken in case of toxicity or corrosivity of the product.  
Before loading switch off the engine and remove the ignition key.  
26.Load hopper with product only after the spreader has been properly attached to the tractor.  
3.02 - Set Up  
Notice to dealer: Pre-Delivery set up and service including lubrication are the responsibility of the  
authorized dealer. It is up to him to assure that the machine is in perfect condition and ready to be  
used. It is his responsibility to ensure that the customer is aware of all safety aspects and operational  
procedures for the spreader. He must also fill out the Pre-Delivery Checklist5 prior to delivering the  
spreader.  
CAUTION: Stand clear of bands when cutting as they could be under sufficient tension to  
cause them to fly loose. Take care in removing bands and wire, as they often have extremely  
sharp edges and cut very easy.  
3.03 - Pre-Operational Check  
Check each of the following, carefully, prior to engaging the equipment:  
1. No wrappings or foreign objects are around the spreader.  
2. All hardware is tight.  
3. All safety shields and guards are in place and tightly attached.  
4. No people or animals are in the work area.  
DANGER: Shut off the tractor and remove the key before making adjustments, servicing or  
cleaning the machine.  
4
See Chapter 4 - Maintenance.  
See Chapter 7 - Pre-Delivery Checklist.  
5
OPERATION  
15  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
3.04 - Attaching to the Tractor  
Unit may be used on tractors ranging from 16 to 30 HP equipped with a standard rear PTO and  
category 1 three point hitch6. Never use this spreader with tractors over 30 HP.  
DANGER: Do not allow anyone to stand between spreader and tractor while attaching  
implement.  
WARNING: Never attempt to attach the implement to the tractor or make an adjustment to it  
without first turning the tractor off.  
CAUTION: Check the tractor PTO rpm to ensure it is set at 540 rpm and turns clockwise.  
CAUTION: Be sure the tractor tire pressure is correct. It is important to strictly follow the  
safety guidelines and instructions laid out in the tractor manual.  
Fig. 7 - Hopper spreading adjustment.  
28" to 32"  
Ground level  
To attach the implement to the tractor do the following:  
Back the tractor up to the implement in order to slip the tractor hitch arms over the hitch pins bolted to  
the frame. Turn off the tractor engine and engage the park brake. Secure the two tractor hitch  
arms to the implement with lynch pins. Tighten the tractor arms side movement with either the sway  
chains or blocks to limit side swing.  
Connect the top link, locking it in place with the top hitch pin. Adjust it so the implement is as near  
parallel to the ground as possible with the spreading disc at a distance 28” to 32” above ground level  
(see fig. 7).  
Install the end of the driveline to the spreader and the opposite end to the tractor PTO. Be sure each  
end is connected securely with either the locking pin or bolt and nut. Connect the driveline shielding  
chains to the tractor and to the implement to prevent the protective shielding from rotating during  
6
See Table 2, page 24.  
OPERATION  
16  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
operation. If it was necessary to remove the PTO shielding to do any of the above operations, do not  
forget to replace it.  
3.05 - Start Up  
CAUTION: Load hopper with product only after the spreader has been properly attached to the  
tractor.  
WARNING: Chemicals may cause eye, skin or breathing problems. Always wear a face mask,  
gloves and goggles when filling hopper. Refer to chemical manufacturer’s label for specific  
safety information.  
Before starting to use, never forget that the operator is responsible for the following:  
1. Safe and correct driving of the tractor and spreader.  
2. To learn precise, safe operating procedures for both the tractor and the spreader.  
3. To ensure all maintenance and lubrication has been performed on the spreader.  
4. To have read and understood all safety aspects for the spreader in the operator’s manual.  
5. To have read and understood all safety decals on the spreader.  
6. Checking the tractor tires for the proper pressure in accordance with the tractor operator’s manual.  
7. Checking that all safety shields are on the machine and securely in place.  
8. Making sure the proper attire is worn. Avoiding loose fitting clothing which can become entangled.  
Wearing sturdy, tough-soled work shoes and protective equipment for eyes, hands, ears and  
head. Never operate tractor or implements in bare feet, sandals or sneakers.  
9. Ensuring proper lighting is available, sunlight or good artificial lighting.  
WARNING: Use a tractor with a cab and appropriate filters on the ventilation system or wear a  
breathing mask capable of filtering toxic powders to prevent inhalation of product.  
Prior to start working do the following:  
1. Make sure there are no obstructions.  
2. Run machine under a no-load condition for a short while to assure that everything is functioning  
properly.  
3. Adjust all settings for the desired quantity distribution and spread pattern.  
4. Shift the transmission to a slow speed gear and start forward, increase the ground speed by  
shifting upward until the desired speed is obtained. Do not use in reverse unless absolutely  
necessary and only after careful observation of the area behind the spreader.  
5. Ballast may need to be added to tractor to maintain steering control.  
3.06 - Operating Techniques  
WARNING: Before adjusting the spreader or filling the hopper, be sure the tractor PTO is not  
engaged, the tractor is shut off, and the key is removed from the tractor ignition.  
OPERATION  
17  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
WARNING: Before engaging the PTO, be sure no persons or animals are behind or beside the  
spreader.  
DANGER: Never allow anyone within 50 yards of the spreader while the PTO is engaged.  
Product thrown from the spreader can cause serious injury or death.  
DANGER: Never allow any person inside the hopper for any reason. Serious injury or death  
can result from someone becoming entangled in the agitator.  
The quantity of material distributed per acre depends on the following factors:  
1. Spreader ground speed.  
2. Unit weight and size of the material to be spread.  
3. Spreading width.  
4. Position of the lever connected to the hopper gates.  
The working speed depends on ground conditions. Only a test run will enable you to gauge the  
optimal working speed for your conditions.  
Spread adjustment for Model SS1023B:  
The spreading is adjustable in three ways by:  
1. Regulating the spread pattern.  
2. Regulating the amount of material to be spread.  
3. Regulating the spreading width.  
To regulate the spread pattern slide (to the left or right) the shutter lever (see #5, fig. 2) which is  
located under the hopper and runs through the slot in the mobile shutter (see #10, fig. 2). To shift the  
shutter lever right or left, loosen the knob over the slotted shield. This moves the spread pattern from  
180° at position 0 (in the center), to either mostly 90° right with the shutter lever shifted all the way to  
the left or mostly 90° left when shifted to the right completely (see fig. 8).  
To regulate the amount of material to be spread, using the same shutter lever as above (see #5,  
fig. 2), slide it in and out to regulate the size of opening at the bottom of the hopper. Use the scale  
located on the shutter lever to gauge the size opening needed. Example: if it is determined that the  
appropriate opening desired is position #6, loosen the knob so the blocking plate will slide. Push the  
lever in until the hole is completely closed and move the blocking plate to position #6 and tighten the  
knob. To spread, pull the lever back until it stops in position #6.  
To regulate the spreading width, you should use the optional rear deflector. Move the deflector up  
and down to change the spreading distance. The higher the deflector is up the further the spread  
width, the lower the less distance the material travels.  
To help the operator set the spreader correctly, Table 37 gives the amount of material distributed  
(lbs/acre) at a spreading widths (20 ft.) for each of the ten lever positions. Example: With the shutter  
lever in position 6, a ground speed of 2.5 mph, spreading at 20 ft., the output should be approximately  
553 lbs. per acre.  
7
See Table 3 - Model SS1023B swath spread patterns, page 25.  
OPERATION  
18  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
Fig. 8  
Three different ways of  
spreading.  
Spread adjustment for Models SS1036B, SS2036B, SS1067B & SS2067B:  
These fertilizer spreaders have two ways of regulating material distribution:  
1. Adjusting the spread position.  
2. Adjusting the quantity of material being spread.  
Adjusting the spread position: The machine can be adjusted to spread to the center or off to either  
of the two sides. This is accomplished by opening the left gate (see #15, fig. 4), right gate (see #5,  
fig. 4) or both. When spreading center behind the tractor, both gates should be open. To spread more  
towards the right, operate the spreader with the right gate open and the left gate closed. To spread  
more to the left, close the right gate and leave the left open. By leaving one of the gates open, the  
spread tends to be heavier in that direction. The side that the closed gate is on will have some  
material dispersed to it, though not as heavy as the other side.  
To open only one gate:  
1. Pull down the lever (see #14, fig. 4) thereby closing both gates, or.  
2. Completely loosen the knob (see #11, fig. 4) on the gate to be left closed.  
When the lever is pulled open, the gate with the loose knob will remain closed.  
One further adjustment possible on Models SS1067B & SS2067B is to adjust the wings (see #20, fig.  
4) that are bolted to the spinner disc (see #19, fig. 4). Moving the wings counterclockwise makes the  
material spread more to the right, whereas moving the wings clockwise will move the spread pattern  
more towards the left (see fig. 9).  
If, for example, the material being spread tends to be thrown center-right and the desired direction is  
more towards the left, simply move the fins counterclockwise and close the right gate.  
Adjusting the quantity of material being spread: To adjust the amount of material being spread,  
move the lever in and out, thereby closing and opening the gates located in the bottom of the hopper.  
Use the scaled rod (see #17, fig. 4) to regulate the amount of opening desired. Completely close the  
gates by pushing the lever (see #14, fig. 4) up. Loosen the plastic knob and move it down to the  
desired number on the scale. Tighten the knob. When the lever is pulled down, it should go down no  
further than the stop plate on the sliding scale.  
OPERATION  
19  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
Use Table 48 to determine the approximate amount of material to be spread in lbs./acre at a 46 foot  
spreading width and put the lever into that position on the sliding scale.  
Example: With the lever in position 5, a ground speed of 5 mph, spreading at 46 ft., the output should  
be approximately 246 lbs. per acre.  
Fig. 9  
Moving the wings in a clockwise  
position will obtain more of a  
left spread pattern.  
Moving the wings in a counter-  
clockwise position will obtain  
more of a right spread pattern.  
3.07 - Uneven Terrain  
WARNING: Be careful of roll-over when operating tractor and spreader over uneven ground.  
The following precautions should always be observed when working on uneven terrain:  
1. In extremely uneven terrain rear wheel weights, front tractor weights, and/or tire ballast should be  
used to improve stability.  
2. Observe the type of terrain and develop a safe working pattern.  
3. Whenever traction or stability is doubtful, first test drive over the terrain.  
4. Operate the implement up and down steep slopes, not across slopes, to prevent the tractor from  
tipping. Avoid sudden stops and starts, and slow down before changing directions on a slope.  
5. Pass diagonally through sharp dips and avoid sharp drops to prevent hanging up the tractor and  
implement.  
6. Slow down on sharp turns and slopes to prevent tipping or loss of control.  
7. Watch for holes, roots or other hidden objects. Do not use near the edge of a gully, ditch or stream  
bank.  
8
See Table 4 - Models SS1036B, SS2036B, SS1067B & SS2067B swath spread patterns, page 25.  
OPERATION  
20  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
4 - MAINTENANCE  
DANGER: Stop engine, lock parking brake and remove key before performing any service or  
maintenance.  
Always use personal protection devices, such as a breathing mask capable of filtering toxic  
powders, safety glasses and gloves, when performing maintenance. Refer to chemical  
manufacturer’s label for specific safety information.  
Keep fingers out of slots to prevent injury.  
4.01 - Maintenance Safety  
1. Good maintenance is your responsibility.  
2. Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use  
adequate light for the job at hand.  
3. Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed  
building. The exhaust fumes may cause asphyxiation.  
4. Make no repair or adjustments with the tractor engine running. Before working on the machine,  
disengage the PTO, shut off the engine, set the brakes, and remove the ignition key.  
5. Be certain all moving parts on attachment have come to a complete stop before attempting to  
perform maintenance.  
6. Never work under equipment unless it is blocked securely.  
7. Always use personal protection devices such as eye, hand and hearing protectors, when  
performing any service or maintenance.  
8. Never trust the tractor hydraulics alone to support the machine. Before repairing or adjusting the  
machine, it should be lowered and allowed to rest on a stand.  
9. Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to  
ensure unit is in a safe condition.  
10.When completing a maintenance or service function, make sure all safety shields and devices are  
installed before placing unit in service.  
11.Do not attempt to mount a tire unless you have the proper equipment and experience to do the  
job.  
12.Inflating or servicing tires can be dangerous. Whenever possible, trained personnel should be  
called to service and/or mount tires.  
13.After servicing, be sure all tools, parts and service equipment are removed.  
14.Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e., shear  
bolts9.  
15.Where replacement parts are necessary for periodic maintenance and servicing, genuine  
replacement parts must be used to restore your equipment to original specifications. The  
Company will not claim responsibility for use of unapproved parts and/or accessories and other  
damages as a result of their use.  
9
Refer to Table 1 - Torque Specifications, for head identification marking, page 24.  
MAINTENANCE  
21  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
16.Unauthorized modifications to the machine may impair the function and/or safety of the machine  
and reduce its life. If equipment has been altered in any way from original design, the  
manufacturer does not accept any liability for injury or warranty.  
4.02 - Service  
Before beginning work:  
1. Apply a thick layer of grease to all exposed moving parts.  
2. Apply a film of biodegradable oil in crevices and corners in order to keep corrosive material from  
rusting areas that are difficult to clean.  
After each use:  
1. Be sure to thoroughly wash the machine without using excessive pressure especially on the  
moving parts. It is particularly important to wash the implement after using salt or fertilizer. This  
will help prevent the caustic chemicals in the salt and fertilizer from destroying the metal of the  
machine.  
2. Carefully dry the machine.  
3. Apply a thick layer of grease to all exposed moving parts.  
4. Apply a film of biodegradable oil in crevices and corners.  
After seasonal use it is important to perform the following for prolonged storage:  
1. Wash and dry the spreader carefully.  
2. Inspect the spreader and replace worn or damaged parts. If corrosive material has eaten under  
the paint, clean off the area with a wire brush and touch up with primer and paint.  
3. Tighten all hardware.  
4. Apply a thick layer of grease to all exposed moving parts.  
5. Apply a film of biodegradable oil in crevices and corners.  
6. Cover the spreader from the elements in order to have it in perfect condition for the start of the  
next season.  
NOTE: The gearbox has been filled with EP grade grease from the factory. The grease never  
needs replacing unless internal work is done to the gearbox. If necessary add SAE 90 oil  
through the suitable cap by giving the proper inclination to the fertilizer spreader.  
4.03 - Driveline  
DANGER: Only use the original driveline supplied with this implement and always with the  
safety shielding. Carefully read and file away the driveline operator’s manual supplied by the  
manufacturer. The following does not substitute the information found in the driveline manual.  
IMPORTANT: Always check driveline length during initial setup and when connecting to a different  
tractor.  
In the collapsed position the driveline should be approximately 2” from bottoming out to prevent  
possible damage to the tractor or implement. When the driveline is in the maximum extended  
position, the ideal minimum overlap of the two halves should be approximately 6” (see fig. 10).  
MAINTENANCE  
22  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
If determined that the driveline is too long, follow these procedures to adjust the length:  
1. Separate the two driveline halves. Connect one half to the tractor PTO and the other half to the  
implement.  
2. Raise and lower the implement with the 3 point hitch to find the position where the driveline is  
shortest. Hold the half shafts side by side and mark the desired length on the outer female tube  
guard leaving a 1 ½” gap between the end of the guard tube and bell guard.  
3. Cut off both guard tubes the same amount as marked in step 2.  
4. Shorten both drive tubes the same amount as guard tubes.  
5. De-burr and clean filings from drive tubes and apply grease to outside of inner telescoping tube.  
6. Reassemble the driveline halves and connect to tractor and implement. Raise and lower  
implement again to be sure driveline does not bottom out in its shortest position and has a  
minimum overlap of 6” in the longest position.  
7. Install both driveline safety chains. One should be hooked in a hole on the outer driveline yoke  
shield and to the tractor to restrict outer shield rotation. The second one should be hooked in a  
hole on the inner driveline yoke shield and to the implement to restrict inner shield rotation.  
If determined that the driveline is too short for your tractor, contact your local dealer.  
Fig. 10  
min. 6"  
MAX.  
min. 2"  
MIN.  
CAUTION: Always work with the driveline as straight as possible. This will prolong its life and  
that of its components. It is advised not to work at an angle greater than 15 degrees.  
4.04 - Transport  
CAUTION: Do not tow tractor and spreader behind other vehicles. Use a properly equipped  
trailer with heavy tie-downs for towing operations.  
Before transporting:  
1. Always select a safe ground speed that is appropriate for the terrain.  
2. Beware of traffic on public roads. Install a SMV (Slow Moving Vehicle) sign when traveling on  
roads or streets. Comply with all federal, state and local laws.  
3. Reduce ground speed when turning and take care that the spreader does not strike obstacles  
such as trees, fences or buildings.  
4. Always disengage PTO before raising spreader to transport position.  
MAINTENANCE  
23  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
TABLE 1 - TORQUE SPECIFICATIONS  
Metric (ISO)  
treaded bolts head  
marking  
Inch (SAE) treaded  
bolts head marking  
Class 5.8 Class 8.8 Class 10.9  
Grade 2  
Grade 5  
Grade 8  
Bolt size  
mm  
Thread  
mm  
Bolt size Thread inch  
N.m  
ft-lb  
N.m  
ft-lb  
N.m  
ft-lb  
N.m  
ft-lb  
N.m  
ft-lb  
N.m  
ft-lb  
inch  
tpi  
M5  
M6  
M8  
M8  
0.8  
1
1.25  
1
1.5  
1.25  
1
1.75  
1.5  
1.25  
2
1.5  
2
1.5  
2.5  
2
1.5  
2.5  
1.5  
2.5  
1.5  
3
4
6
16  
17  
31  
33  
35  
54  
56  
3
4
12  
13  
23  
24  
26  
40  
41  
44  
62  
69  
6
10  
25  
26  
48  
51  
53  
84  
87  
4
7
18  
19  
35  
38  
39  
62  
9
15  
36  
38  
71  
75  
78  
123  
128  
133  
195  
209  
302  
320  
421  
443  
465  
592  
646  
807  
873  
1017  
1095  
7
11  
27  
28  
52  
55  
58  
91  
1/4”  
1/4”  
5/16”  
5/16”  
3/8”  
20  
28  
18  
24  
16  
24  
14  
20  
13  
20  
12  
18  
11  
18  
10  
16  
9
14  
8
12  
7
12  
7
12  
6
7
8
15  
17  
27  
31  
43  
48  
66  
5
6
11  
13  
20  
23  
32  
36  
48  
55  
70  
79  
11  
13  
24  
26  
42  
47  
67  
75  
102  
115  
147  
164  
203  
230  
361  
403  
582  
642  
873  
955  
1077  
1208  
8
10  
17  
19  
31  
35  
49  
55  
16  
19  
33  
37  
59  
12  
14  
25  
27  
44  
49  
70  
78  
106  
120  
154  
171  
212  
240  
376  
420  
606  
668  
909  
995  
M10  
M10  
M10  
M12  
M12  
M12  
M14  
M14  
M16  
M16  
M18  
M18  
M18  
M20  
M20  
M22  
M22  
M24  
M24  
M27  
M27  
M30  
M30  
M36  
3/8”  
67  
95  
7/16”  
7/16”  
1/2”  
106  
144  
163  
208  
232  
287  
325  
509  
569  
822  
906  
1232  
1348  
64  
66  
98  
94  
98  
75  
85  
59  
84  
94  
90  
1/2”  
75  
95  
133  
142  
206  
218  
295  
311  
327  
415  
454  
567  
613  
714  
769  
1050  
1119  
144  
154  
223  
236  
310  
327  
343  
437  
476  
595  
644  
750  
808  
9/16”  
9/16”  
5/8”  
5/8”  
3/4”  
3/4”  
7/8”  
7/8”  
1”  
109  
121  
150  
170  
266  
297  
430  
473  
644  
704  
794  
891  
105  
152  
161  
218  
229  
241  
306  
335  
418  
452  
526  
567  
774  
825  
106  
132  
149  
233  
261  
226  
249  
339  
371  
480  
539  
677  
750  
888  
1011  
1179  
1326  
131  
141  
181  
196  
203  
256  
288  
344  
381  
444  
488  
656  
719  
906  
1000  
97  
97  
104  
133  
145  
150  
189  
212  
254  
281  
327  
360  
484  
530  
668  
738  
110  
172  
192  
167  
184  
250  
273  
354  
397  
500  
553  
655  
746  
869  
978  
1”  
1-1/8”  
1-1/8”  
1-1/4”  
1-1/4”  
1-3/8”  
1-3/8”  
1-1/2”  
1-1/2”  
1746 1288  
1958 1445  
2
3
2
3.5  
2
1519 1120 2463 1817  
1682 1241 2728 2012  
1992 1469 3230 2382  
2268 1673 3677 2712  
2643 1949 4286 3161  
2974 2194 4823 3557  
1496 1103  
1594 1176  
1420 1047 2033 1499  
1600 1180 2250 1659  
12  
6
12  
4
1534 1131 2482 1830 3535 2607  
When using lock washers with nuts, increase torque values by 5%.  
TABLE 2 - FERTILIZER SPREADER - TECHNICAL FEATURES  
For tractors from 16 to 30 HP, PTO 540 rpm, 3 point hitch cat. 1  
Model  
HP  
Hopper  
capacity  
cu. ft.  
Carrying  
weight  
lbs.  
Weight  
lbs.  
Loading  
height  
Loading  
width  
Spreading  
width ft.  
Driveline  
1 3/8”  
SS1023B  
SS1036B  
SS2036B  
SS1067B  
SS2067B  
16-30  
16-30  
16-30  
16-30  
16-30  
3.5  
5.6  
226  
362  
362  
678  
678  
81  
31”  
34”  
34”  
40”  
40”  
32”  
35”  
35”  
42”  
42”  
23’  
23’  
23’  
46’  
46’  
ASAE cat. 1  
ASAE cat. 1  
ASAE cat. 1  
ASAE cat. 1  
ASAE cat. 1  
102  
102  
125  
125  
5.6  
10.6  
10.6  
MAINTENANCE  
24  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
TABLE 3 - MODEL SS1023B SWATH SPREAD PATTERNS (lbs/acre)  
Spreading width  
20 feet  
Lever position  
2.5 mph  
89  
3.75 mph  
5 mph  
39  
1
2
45  
143  
89  
71  
3
223  
152  
196  
277  
330  
410  
473  
562  
625  
107  
152  
205  
277  
321  
384  
437  
500  
4
312  
5
419  
6
553  
7
651  
8
767  
9
874  
10  
999  
TABLE 4 - MODELS SS1036B, SS2036B, SS1067B & SS2067B SWATH SPREAD  
PATTERNS (lbs/acre)  
Spreading width  
46 feet  
Lever position  
2.5 mph  
5 mph  
39  
7.5 mph  
16  
1
2
3
4
5
6
7
8
9
50  
123  
246  
369  
492  
-
61  
43  
123  
184  
246  
307  
369  
430  
492  
82  
123  
166  
201  
-
246  
-
282  
-
323  
MAINTENANCE  
25  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
5 - REPAIR PROCEDURES  
CAUTION: All repair procedures must be done by authorized dealerships. It is not  
recommended that untrained individuals perform any repair work.  
5.01 - Suggested Spare Parts  
It is suggested that the following spare parts be kept on hand for the spreader at all times to prevent a  
minor problem from delaying work:  
Models SS1023B, SS1036B & SS2036B  
Description  
Quantity  
Spreader disc (5BP501650B)  
Threaded Bushing (5BP501622B)  
Nut M30 (5BP501651B)  
1
1
1
Models SS1067B & SS2067B  
Description  
Quantity  
Spreader disc wings (5BP501598B)  
Stirrer (5BP501597B)  
4
1
5.02 - Storage  
After seasonal use it is important to perform the following for prolonged storage:  
1. Empty hopper of product before unhooking it from the tractor.  
2. Wash and dry the spreader carefully.  
3. Inspect the spreader and replace worn or damaged parts. If corrosive material has eaten under  
the paint, clean off the area with a wire brush and touch up with primer and paint.  
4. Tighten all hardware.  
5. Grease or oil all areas indicated under Maintenance10.  
6. Apply a thick layer of grease to all exposed moving parts.  
7. Cover the spreader from the elements in order to have it in perfect condition for the start of the  
next season.  
8. Make sure all parked machines are on a hard, level surface, and engage all safety devices.  
9. Do not permit children to play on or around the stored unit.  
Touch up paint available:  
Description  
Part #  
5BP7300007 Primer, gray - aerosol spray can  
5BP7300011 Paint, green - aerosol spray can  
5BP7300010 Paint, black - aerosol spray can  
10  
See Chapter 4 - Maintenance.  
REPAIR PROCEDURES  
26  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
6 - TROUBLESHOOTING  
WARNING: Be sure tractor engine is off, parking brake is locked, and key is removed before  
making any adjustments.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
Non uniform spread Spreader disc wings not  
Position spreader disc wings to the proper  
setting (see section 3.06 - Operating  
Techniques).  
pattern.  
positioned properly.  
Wrong gate opening.  
Adjust gate openings.  
Product not flowing Wet product.  
to spreader disc.  
Use dry product only.  
Powdered product.  
Roll pin missing or sheared on  
but not the gearbox the spreader disc shaft.  
Use optional tumbling agitator.  
Replace roll pin.  
PTO shaft turning  
output shaft.  
Broken ring or pinion gear.  
Replace ring or pinion gear.  
Narrow spread  
width.  
Incorrect PTO speed.  
Increase PTO speed to 540 rpm.  
Hopper too far backwards.  
Shorten the tractor’s top link to position  
spreader so it runs level or inclined slightly  
forward toward the tractor.  
TROUBLESHOOTING  
27  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
OPERATOR’S MANUAL  
7 - PRE-DELIVERY CHECKLIST  
To the dealer: Inspect the machine thoroughly after assembly to assure it is functioning  
properly before delivering it to the customer. The following checklist is a reminder of points to  
cover. Check off each item as it is found satisfactory or after proper adjustment is made.  
Gearbox oil level.  
Guards and shield properly fastened.  
Lubrication of grease fittings.  
All hardware properly tightened.  
All decals properly located and readable (see fig. 6).  
Overall condition (touch up scratches, clean and polish).  
Test run, check for excessive vibration or overheating of bearings.  
Operator’s Manual.  
Review the Operator’s Manual with the customer. Explain the following:  
Warranty.  
Safe operation and service.  
Correct machine installation and operation.  
Daily and periodic lubrication, maintenance and inspections.  
Troubleshooting.  
Operational procedures and storage.  
Parts and service.  
Fill out the Pre-Delivery Checklist and the on-line Warranty Registration form.  
Give customer the Operator’s Manual and encourage the customer to read the manual carefully.  
IMPORTANT: The dealer must complete the Warranty Registration, located on the Frontier  
website. Warranty claims will be denied if the Warranty Registration has not been completed.  
Model Number: __________  
Delivery Date: __________  
Serial Number: __________  
Dealer’s Signature: __________  
PRE-DELIVERY CHECKLIST  
28  
FRONTIER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P A R T S M A N U A L  
FERTILIZER SPREADERS  
SS1023B  
SS1036B  
SS1067B  
SS2036B  
SS2067B  
Note: Serial #’s with the XF prefix are subsequent to serial numbers with the BC prefix. For example: A  
reference to “serial # BC… 739197 & above” will also include all serial numbers with an XF prefix.  
Parts Manual 05/2011  
Frontier Hop 203, 206, 209 (US)  
Printed on May 19, 2011  
203-120 Ver. D  
206-121, 206-221 Ver. B  
209-121, 209-421, 209-422 Ver. C  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1023B  
PARTS MANUAL  
32  
FRONTIER  
02/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1023B  
Ref.  
1
Part #  
Description  
Qty.  
1
1
2
1
1
1
2
1
1
1
1
1
1
2
3
6
7
8
2
1
1
1
1
1
4
4
4
4
5BP501660B  
5BP0014620  
5BP0014616  
5BP501661B  
5BP501668B  
5BP501630B  
5BP501631B  
5BP501639B  
5BP501123B  
5BP501622B  
5BP501652B  
5BP501650B  
5BP501670B  
5BP0014710  
5BP501663B  
5BP0015230  
5BP0014514  
5BP0001806  
5BP0046454  
5BP0011209  
5BP0015220  
5BP0091384  
5BP501651B  
5BP0041291  
5BP0015273  
5BP0002034  
5BP0001280  
5BP0090150  
Frame w/cat. 0/1 hitch; SS1023B #XF...287132 & below11  
Frame w/cat. 1 hitch; SS1023B #XF...287133 & above  
Rubber cap Ø45  
2
3
4
5
6
7
8
9
10  
11  
15  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
Hopper, steel; SS1023B  
Guard  
Flow control assembly  
Adjustment knob M6x16  
Adjustment knob  
Stirrer  
Threaded bushing M20  
Mobile shutter  
Spreader disc  
Gearbox, complete  
Bushing cat. 0/1; #XF...287132 & below  
Bolt CR M08-1.25x25 C4.6 Z  
Washer flat Ø8 W  
Washer fender Ø8 Z  
Nut HH M08-1.25 C6 Z TK  
Bolt HH M08-1.25x16 C8.8 Z F  
Washer fender Ø6 Z  
Bolt HH M08-1.25x35 C8.8 Z F  
Nut ES M08-1.25 Z TK  
Nut HH M30-2.00 C6 Z TN  
Hairpin cotter Ø5 Z  
Bolt HH M10-1.50x110 C8.8 Z P  
Washer flat Ø10 W  
Washer lock Ø10 Z  
Nut HH M10-1.50 C6 Z MD  
5BP950355B  
5BP950109B  
5BP950338B  
5BP950339B  
5BP950417B  
5BP950942B  
5BP950439B  
5BP950440B  
5BP950346B  
5BP950361B  
5BP960376B  
Spreader safety decal kit complete  
Decal “DANGER - Avoid injury from PTO”  
Decal “WARNING - Toxic chemical hazard”  
Decal “WARNING - Thrown objects, moving parts hazard”  
Decal “CAUTION - To avoid serious injury”  
Decal “spread chart”; SS1023B  
Decal selector “1-10” large  
Decal selector “1-10” small  
Decal “FRONTIER”  
Decal “SS1023B”  
-
1
1
1
1
1
1
1
1
1
-
Operator’s & Parts Manual Frontier Fertilizer Spreaders  
SS1023B, SS1036B, SS2036B, SS1067B & SS2067B  
11  
Interchangeable with part #5BP0014620 if spreader is used on a tractor with a cat. 1 hitch.  
PARTS MANUAL  
33  
FRONTIER  
02/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1036B  
PARTS MANUAL  
34  
FRONTIER  
05/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1036B  
Ref.  
1
Part #  
Description  
Qty.  
1
1
2
1
1
1
1
1
1
2
2
1
1
3
1
1
1
1
1
1
1
1
1
2
3
3
1
3
4
1
1
4
6
11  
1
1
4
9
3
7
6
2
2
4
1
5BP0014601  
5BP0014625  
5BP0014616  
5BP0214624  
5BP0014630  
5BP0014632  
5BP0014338  
5BP0114640  
5BP0214640  
5BP0014641  
5BP502024B  
5BP502025B  
5BP502002B  
5BP501589B  
5BP501585B  
5BP501586B  
5BP0014643  
5BP0014391  
5BP0014645  
5BP502008B  
5BP501597B  
5BP0014647  
5BP0014690  
5BP0014710  
5BP501663B  
5BP0015012  
5BP0046454  
5BP0084289  
5BP0046543  
5BP0007128  
5BP0014427  
5BP0015273  
5BP0001806  
5BP0046545  
5BP0013345  
5BP0091384  
5BP0090150  
5BP0015230  
5BP0014514  
5BP0003144  
5BP0002034  
5BP0030157  
5BP0091435  
5BP0001280  
5BP0041291  
5BP950369B  
5BP950432B  
Frame w/cat. 0/1 hitch; SS1036B, #XF...288985 & below12  
Frame w/cat. 1 hitch; SS1036B, #XF...288986 & above  
Rubber cap Ø45  
2
3
4
5
6
7
8
9
Hopper; SS1036B  
Protection  
Protection  
Attachment plate  
Shutter, right  
Shutter, left  
Tie rod  
Tension spring  
Shutter guide plate  
Lever bracket  
Adjustment knob M8x15  
Washer flat nylon Ø12  
Spring  
Lever  
Rubber cap  
Scaled rod  
Lever stop  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
Stationary stirrer  
Spreader disc  
Gearbox, complete  
Bushing cat. 0/1; #XF...288985 & below  
Bolt CR M08-1.25x25 C4.6 Z  
Bolt HH M08-1.25x20 C8.8 Z F  
Bolt HH M08-1.25x16 C8.8 Z F  
Bolt CR M08-1.25x20 C4.6 Z  
Bolt HH M08-1.25x30 C8.8 Z F  
Bolt HH M12-1.75x80 C8.8 Z F  
Bolt HH M08-1.25x45 C8.8 Z P  
Bolt HH M10-1.50x110 C8.8 Z P  
Nut HH M08-1.25 C6 Z TK  
Nut HH M08-1.25 C6 Z MD  
Nut ES M12-1.75 Z TK  
Nut ES M08-1.25 Z TK  
Nut HH M10-1.50 C6 Z MD  
Washer flat Ø8 W  
Washer fender Ø8 Z  
Washer lock Ø8 Z  
Washer flat Ø10 W  
Washer fender Ø10 Z  
Washer flat Ø14 W  
Washer lock Ø10 Z  
Hairpin cotter Ø5 Z  
Decal “spread chart”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SS1036B”  
1
1
12  
Interchangeable with part #5BP0014625 if spreader is used on a tractor with a cat. 1 hitch.  
PARTS MANUAL  
35  
FRONTIER  
05/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS2036B  
PARTS MANUAL  
36  
FRONTIER  
05/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS2036B  
Ref.  
1
Part #  
Description  
Qty.  
1
1
2
1
1
1
1
1
1
2
2
1
1
3
1
1
1
1
1
1
1
1
1
2
3
3
1
7
4
1
1
4
6
16  
1
1
4
9
8
12  
6
2
2
4
1
1
1
5BP0014601  
5BP0014625  
5BP0014616  
5BP0214629  
5BP0014630  
5BP0014632  
5BP0014635  
5BP0114648  
5BP0214648  
5BP0014641  
5BP502024B  
5BP502025B  
5BP502002B  
5BP501589B  
5BP501585B  
5BP501586B  
5BP0014643  
5BP0014391  
5BP0014645  
5BP502008B  
5BP501597B  
5BP0014647  
5BP0014690  
5BP0014710  
5BP0014619  
5BP0015012  
5BP0046454  
5BP0084289  
5BP0046543  
5BP0007128  
5BP0014427  
5BP0015273  
5BP0001806  
5BP0046545  
5BP0013345  
5BP0091384  
5BP0090150  
5BP0015230  
5BP0014514  
5BP0003144  
5BP0002034  
5BP0030157  
5BP0091435  
5BP0001280  
5BP0041291  
5BP501663B  
5BP0014327  
5BP950369B  
5BP950433B  
Frame w/cat. 0/1 hitch; SS2036B, #XF...288985 & below13  
Frame w/cat. 1 hitch; SS2036B, #XF...288986 & above  
Rubber cap Ø45  
2
3
4
5
6
7
8
9
Polyethylene hopper; SS2036B  
Protection  
Protection  
Attachment plate  
Shutter stainless steel, right  
Shutter stainless steel, left  
Tie rod  
Tension spring  
Shutter guide plate  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
Lever bracket  
Adjustment knob M8x15  
Washer flat nylon Ø12  
Spring  
Lever  
Rubber cap  
Scaled rod  
Lever stop  
Stationary stirrer  
Spreader disc  
Gearbox, complete  
Bushing cat. 0/1; #XF...288985 & below  
Bolt CR M08-1.25x35 C4.6 Z  
Bolt HH M08-1.25x20 C8.8 Z F  
Bolt HH M08-1.25x16 C8.8 Z F  
Bolt CR M08-1.25x20 C4.6 Z  
Bolt HH M08-1.25x30 C8.8 Z F  
Bolt HH M12-1.75x80 C8.8 Z F  
Bolt HH M08-1.25x45 C8.8 Z P  
Bolt HH M10-1.50x110 C8.8 Z P  
Nut HH M08-1.25 C6 Z TK  
Nut HH M08-1.25 C6 Z MD  
Nut ES M12-1.75 Z TK  
Nut ES M08-1.25 Z TK  
Nut HH M10-1.50 C6 Z MD  
Washer flat Ø8 W  
Washer fender Ø8 Z  
Washer lock Ø8 Z  
Washer flat Ø10 W  
Washer fender Ø10 Z  
Washer flat Ø14 W  
Washer lock Ø10 Z  
Hairpin cotter Ø5 Z  
Bolt CR M08-1.25x25 C4.6 Z  
Hopper bottom plate, stainless steel  
Decal “spread chart”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SS2036B”  
1
1
13  
Interchangeable with part #5BP0014625 if spreader is used on a tractor with a cat. 1 hitch.  
PARTS MANUAL  
37  
FRONTIER  
05/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1067B  
PARTS MANUAL  
38  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS1067B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Frame; SS1067B, SS2067B  
Rubber cap Ø60  
Hopper, steel; SS1067B  
Protection  
Shutter, right  
Shutter, left  
Tie rod  
Tension spring  
Shutter guide plate  
Lever bracket  
Adjustment knob M8x15  
Washer flat nylon Ø12  
Spring  
Lever  
Hitch lever  
Nut HH M10-1.50 C6 Z MD  
Scaled rod  
Lever stop  
Spreader disc, steel  
Spreader wing, steel  
Stationary stirrer  
Gearbox, complete  
Bolt CR M12-1.75x30 C4.6 Z  
Washer flat Ø14 W  
Nut HH M12-1.75 C6 Z MD  
Bolt HH M08-1.25x20 C8.8 Z F  
Washer flat Ø8 W  
Nut HH M08-1.25 C6 Z MD  
Bolt HH M08-1.25x30 C8.8 Z F  
Washer lock Ø8 Z  
Washer flat Ø10 W  
Bolt HH M12-1.75x80 C8.8 Z F  
Nut ES M12-1.75 Z TK  
Roll pin Ø8x40  
Qty.  
1
2
1
1
1
1
2
2
1
1
3
1
1
1
1
4
1
1
1
4
1
1
3
5
6
4
7
9
4
5
6
1
1
1
1
8
8
8
1
1
4
4
1
1
1
-
5BP502011B  
5BP502020B  
5BP502014B  
5BP502013B  
5BP502009B  
5BP502003B  
5BP502004B  
5BP502024B  
5BP502025B  
5BP502002B  
5BP501589B  
5BP501585B  
5BP501586B  
5BP0014380  
5BP0014384  
5BP0090150  
5BP0014396  
5BP502008B  
5BP501599B  
5BP501598B  
5BP501597B  
5BP0014690  
5BP0051073  
5BP0091435  
5BP0001106  
5BP0015012  
5BP0015230  
5BP0046545  
5BP0046543  
5BP0003144  
5BP0002034  
5BP0007128  
5BP0013345  
5BP0029247  
5BP501596B  
5BP0036319  
5BP0046536  
5BP501603B  
5BP0014427  
5BP0091384  
5BP0015273  
5BP0001280  
5BP0014391  
5BP0014338  
5BP0084289  
5BP950355B  
5BP950369B  
5BP950353B  
5BP950348B  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
44  
45  
46  
Roll pin Ø5x40  
Bolt HH M06-1.00x16 C8.8 Z F  
Washer lock Ø6 Z  
Nut HH M06-1.00 C6 Z TK  
Bolt HH M08-1.25x45 C8.8 Z P  
Nut ES M08-1.25 Z TK  
Bolt HH M10-1.50x110 C8.8 Z P  
Washer lock Ø10 Z  
Rubber cap  
Attachment plate, steel hopper; SS1067B  
Bolt CR M08-1.25x20 C4.6 Z  
Spreader safety decal kit complete  
Decal “spread chart”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SMV”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SS1067B”  
1
1
1
PARTS MANUAL  
39  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS2067B  
PARTS MANUAL  
40  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
FRAME  
OPERATOR’S MANUAL  
SS2067B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Frame; SS1067B, SS2067B  
Rubber cap Ø60  
Hopper polyethylene; SS2067B  
Protection  
Shutter stainless steel, right  
Shutter stainless steel, left  
Tie rod  
Tension spring  
Shutter guide plate  
Lever bracket  
Adjustment knob M8x15  
Washer flat nylon Ø12  
Spring  
Lever  
Hitch lever  
Nut HH M10-1.50 C6 Z MD  
Scaled rod  
Lever stop  
Spreader disc, stainless steel  
Spreader wing, stainless steel  
Stationary stirrer  
Gearbox, complete  
Bolt CR M12-1.75x40 C8.8 Z  
Washer flat Ø14 W  
Nut HH M12-1.75 C6 Z MD  
Bolt HH M08-1.25x20 C8.8 Z F  
Washer flat Ø8 W  
Nut HH M08-1.25 C6 Z MD  
Bolt HH M08-1.25x30 C8.8 Z F  
Washer lock Ø8 Z  
Qty.  
1
2
1
1
1
1
2
2
1
1
3
1
1
1
1
4
1
1
1
4
1
1
3
5
6
4
7
14  
4
10  
6
1
1
1
1
8
8
8
1
1
4
4
1
5
1
5
1
1
5BP502011B  
5BP502020B  
5BP0114326  
5BP502013B  
5BP0114340  
5BP0214340  
5BP502004B  
5BP502024B  
5BP502025B  
5BP502002B  
5BP501589B  
5BP501585B  
5BP501586B  
5BP0014380  
5BP0014384  
5BP0090150  
5BP0014396  
5BP502008B  
5BP0014410  
5BP0014414  
5BP501597B  
5BP0014690  
5BP0044115  
5BP0091435  
5BP0001106  
5BP0015012  
5BP0015230  
5BP0046545  
5BP0046543  
5BP0003144  
5BP0002034  
5BP0007128  
5BP0013345  
5BP0029247  
5BP501596B  
5BP0036319  
5BP0046536  
5BP501603B  
5BP0014427  
5BP0091384  
5BP0015273  
5BP0001280  
5BP0014327  
5BP0084289  
5BP501663B  
5BP0014514  
5BP0014339  
5BP0014391  
5BP950369B  
5BP950353B  
5BP950434B  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
44  
45  
46  
47  
48  
49  
Washer flat Ø10 W  
Bolt HH M12-1.75x80 C8.8 Z F  
Nut ES M12-1.75 Z TK  
Roll pin Ø8x40  
Roll pin Ø5x40  
Bolt HH M06-1.00x16 C8.8 Z F  
Washer lock Ø6 Z  
Nut HH M06-1.00 C6 Z TK  
Bolt HH M08-1.25x45 C8.8 Z P  
Nut ES M08-1.25 Z TK  
Bolt HH M10-1.50x110 C8.8 Z P  
Washer lock Ø10 Z  
Hopper bottom plate, stainless steel  
Bolt CR M08-1.25x20 C4.6 Z  
Bolt CR M08-1.25x25 C4.6 Z  
Washer fender Ø8 Z  
Attachment plate, poly hopper  
Rubber cap  
Decal “spread chart”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SMV”; SS1036B, SS2036B, SS1067B, SS2067B  
Decal “SS2067B”  
1
1
1
PARTS MANUAL  
41  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
SAFETY SHIELD  
OPERATOR’S MANUAL  
SS1067B, SS2067B - SERIAL #BC…304879 & ABOVE  
Ref.  
1
2
Part #  
Description  
Protection  
Attachment plate, steel hopper; SS1067B  
Attachment plate, poly hopper; SS2067B  
Bolt HH M08-1.25x16 C8.8 Z F  
Washer flat Ø8 W  
Qty.  
1
1
1
3
7
1
4
1
5BP0014337  
5BP0014338  
5BP0014339  
5BP0046454  
5BP0015230  
5BP0003144  
5BP0046545  
5BP0084289  
5BP501663B  
3
4
5
6
7
Washer lock Ø8 Z  
Nut HH M08-1.25 C6 Z MD  
Bolt CR M08-1.25x20 C4.6 Z; SS1067B  
Bolt CR M08-1.25x25 C4.6 Z; SS2067B  
1
PARTS MANUAL  
42  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
DRIVELINE  
OPERATOR’S MANUAL  
SERIAL #BC…736780 & BELOW  
Ref.  
1
Part #  
Description  
Qty.  
2
5BP1021010C PTO yoke  
2
3
4
5
6
7
8
9
5BP1001005C Cross & bearing  
5BP1981034NC Outer tube w/yoke  
5BP1991035NC Inner tube w/yoke  
5BP1006065C Chain, anti-rotation  
5BP1781210C Locking ring, outer tube  
5BP1784201C Rigid cone, outer tube  
5BP1784203C Standard cone  
5BP1784212C Pin  
2
1
1
2
1
1
2
2
10  
11  
12  
13  
14  
15  
16  
17  
5BP1773032C Shield, outer tube  
5BP1872032C Shield, inner tube  
5BP1213233C Stiffening ring  
5BP1784202C Rigid cone, inner tube  
5BP1781211C Locking ring, inner tube  
5BP90SS1032C Shield, complete14  
5BP950463B  
1
1
2
1
1
1
1
1
1
Decal “DANGER - Rotating driveline, keep away” outer shield  
5BP950464B  
5BP0500474  
Decal “DANGER - Guard missing, do not operate” outer tube  
Driveline, complete15  
14  
15  
Complete shielding is no longer available, replace with part #5BP90SS1032CA.  
Complete shaft is no longer available, replace with part #5BP0500487.  
PARTS MANUAL  
43  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
DRIVELINE  
OPERATOR’S MANUAL  
SERIAL #BC…736781 & ABOVE  
Ref. Part #  
Description  
PTO yoke  
Cross & bearing  
Qty.  
2
2
1
5BP1021010C  
5BP1001005C  
2
3
4
5
6
7
8
9
10  
11  
12  
13  
5BP1981034NC Outer tube w/yoke  
5BP1991035NC Inner tube w/yoke  
5BP1781210CA Locking ring, outer tube  
5BP1784203CA Cone, outer tube  
5BP1773032CA Shield, outer tube  
5BP1872032CA Shield, inner tube  
5BP1781211CA Locking ring, inner tube  
5BP90SS1032CA Shield, complete  
1
1
1
2
1
1
1
1
5BP1006065C  
5BP950463B  
5BP950464B  
5BP0500487  
Chain, anti-rotation  
2
Decal “DANGER - Rotating driveline, keep away” outer shield  
Decal “DANGER - Guard missing, do not operate” outer tube  
Driveline, complete  
1
1
-
PARTS MANUAL  
44  
FRONTIER  
04/2009  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
DRIVELINE FOR QUICK HITCH/IMATCH (OPTION)  
SERIAL #BC…736781 & ABOVE  
OPERATOR’S MANUAL  
Ref.  
1
Part #  
Description  
Qty.  
2
5BP1021010C PTO yoke  
2
5BP1001005C Cross & bearing  
2
3
4
5BP0014444  
5BP0014445  
Outer tube w/yoke  
Inner tube w/yoke  
1
1
5
6
5BP1781210CA Locking ring, outer tube  
5BP1784203CA Cone, outer tube  
1
2
7
8
5BP0014446  
5BP0014447  
Shield, outer tube  
Shield, inner tube  
1
1
9
5BP1781211CA Locking ring, inner tube  
5BP0014448 Shield, complete  
1
1
2
1
1
-
10  
11  
12  
13  
5BP1006065C Chain, anti-rotation  
5BP950463B  
Decal “DANGER - Rotating driveline, keep away” outer shield  
5BP950464B  
5BP0500484  
Decal “DANGER - Guard missing, do not operate” outer tube  
Driveline, complete  
PARTS MANUAL  
45  
FRONTIER  
04/2009  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
REMOTE GATE CONTROL (OPTION)  
OPERATOR’S MANUAL  
SS1023B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Qty.  
1
1
1
1
3
1
1
1
1
1
1
1
1
1
2
1
1
1
4
-
5BP0014981  
5BP0014982  
5BP0014983  
5BP0014477  
5BP0002034  
5BP0014988  
5BP0014989  
5BP0015237  
5BP0014990  
5BP0014991  
5BP0014992  
5BP0014997  
5BP501639B  
5BP0014999  
5BP501631B  
5BP0011209  
5BP0014993  
5BP0014994  
5BP0014998  
5BP0099856  
Support plate, remote gate control  
Lever, remote gate control  
Handle, flat grooved  
Bolt HH M10-1.50x60 C8.8 Z P  
Washer flat Ø10 W  
Spacer  
Spring  
Nut ES M10-1.50 Z TN  
Cable support  
Snap ring, outer Ø10  
Cable; until 08-200816  
Cable; since 09-2008  
Adjustment knob  
Flow control assembly  
Adjustment knob M6x16  
Washer fender Ø6 Z  
Cable support plate  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
Cable hitch plate  
Bolt CS M04-0.70x10 C8.8 Z F  
Remote gate control, complete; SS1023B  
16  
Part #5BP0014992 no longer available, customer should replace entire accessory.  
PARTS MANUAL  
46  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
REMOTE GATE CONTROL (OPTION)  
OPERATOR’S MANUAL  
SS1036B, SS2036B, SS1067B, SS2067B  
Ref.  
1
Part #  
Description  
Qty.  
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
5BP0114981  
5BP0014981  
5BP0014982  
5BP0014983  
5BP0014477  
5BP0002034  
5BP0014988  
5BP0014989  
5BP0015237  
5BP0014990  
5BP0014991  
5BP0014992  
5BP0014997  
5BP0014590  
5BP0014594  
5BP0015255  
5BP0002265  
5BP0013345  
5BP0003144  
5BP0046454  
5BP0099850  
Support plate, remote gate control; until 08-2008  
Support plate, remote gate control; since 09-2008  
Lever, remote gate control  
Handle, flat grooved  
Bolt HH M10-1.50x60 C8.8 Z P  
Washer flat Ø10 W  
Spacer  
Spring  
Nut ES M10-1.50 Z TN  
Cable support  
2
3
4
5
6
7
8
9
10  
11  
Snap ring, outer Ø10  
Cable; until 08-200817  
Cable; since 09-2008  
Bracket, cable support  
Cable support  
12  
13  
14  
15  
16  
17  
18  
Bolt HH M12-1.75x30 C8.8 Z F  
Washer flat Ø12 W  
Nut ES M12-1.75 Z TK  
Washer lock Ø8 Z  
Bolt HH M08-1.25x16 C8.8 Z F  
Remote gate control, complete; SS1036B, SS2036B, SS1067B,  
SS2067B  
1
1
1
1
-
17  
Part #5BP0014992 no longer available, customer should replace entire accessory.  
PARTS MANUAL  
47  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
TUMBLING AGITATOR 5BPAA2120 (OPTION) UNTIL 02/2011  
OPERATOR’S MANUAL  
SS1023B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Qty.  
1
1
1
1
1
1
2
4
2
1
2
1
5BP0014721  
5BP0014730  
5BP0014735  
5BP502005B  
5BP0002265  
5BP502006B  
5BP0014477  
5BP0002034  
5BP0014106  
5BP0014427  
5BP0015230  
5BP0091384  
5BPAA2120  
Stirrer, tumbling agitator  
Hitch, tumbling agitator  
Beam, tumbling agitator  
Wheel, tumbling agitator  
Washer flat Ø12 W  
Cotter pin Ø4x35  
Bolt HH M10-1.50x60 C8.8 Z P  
Washer flat Ø10 W  
Nut ES M10-1.50 Z TK  
Bolt HH M08-1.25x45 C8.8 Z P  
Washer flat Ø8 W  
Nut ES M08-1.25 Z TK  
Tumbling agitator, complete; SS1023B (until 02-2011)  
9
10  
11  
12  
13  
-
PARTS MANUAL  
48  
FRONTIER  
01/2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
TUMBLING AGITATOR 5BP0099979 (OPTION) SINCE 03/2011  
OPERATOR’S MANUAL  
SS1023B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Qty.  
1
1
1
1
2
1
3
1
1
2
1
1
5BP0014742  
5BP0014739  
5BP0014744  
5BP0076106  
5BP0030064  
5BP0014746  
5BP0002265  
5BP0014488  
5BP0001174  
5BP0015230  
5BP0091384  
5BP0014427  
5BP0099979  
Stirrer, tumbling agitator  
Hitch, tumbling agitator  
Beam, tumbling agitator  
Washer fender Ø12 Z  
Nut PT M12-1.75 C6 TK Z  
Bolt HH M12-1.75x60 C8.8 ZP  
Washer flat Ø12 W  
Wheel, tumbling agitator  
Cotter pin Ø4x35  
Washer flat Ø08 W  
9
10  
11  
12  
Nut ES M08-1.25 Z TK  
Bolt HH M08-1.25x45 C8.8 Z P  
Tumbling agitator, complete; SS1023B (since 03/2011)  
-
PARTS MANUAL  
49  
FRONTIER  
03/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
TUMBLING AGITATOR 5BPAA3120 (OPTION) UNTIL 02/2011  
OPERATOR’S MANUAL  
SS1036B, SS2036B, SS1067B, SS2067B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Qty.  
1
1
1
1
2
1
1
1
1
2
1
-
5BP502019B  
5BP502007B  
5BP502005B  
5BP0014490  
5BP0015230  
5BP0091384  
5BP0002265  
5BP502006B  
5BP0014477  
5BP0002034  
5BP0014106  
5BPAA3120  
Stirrer, tumbling agitator  
Beam, tumbling agitator  
Wheel, tumbling agitator  
Bolt HH M08-1.25x50 C8.8 Z P  
Washer flat Ø8 W  
Nut ES M08-1.25 Z TK  
Washer flat Ø12 W  
Cotter pin Ø4x35  
Bolt HH M10-1.50x60 C8.8 Z P  
Washer flat Ø10 W  
Nut ES M10-1.50 Z TK  
Tumbling agitator, complete; SS1036B, SS2036B, SS1067B,  
SS2067B (until 02/2011)  
9
10  
11  
12  
PARTS MANUAL  
50  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
TUMBLING AGITATOR 5BP0099978 (OPTION) SINCE 03/2011  
OPERATOR’S MANUAL  
SS1036B, SS2036B, SS1067B, SS2067B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Qty.  
1
1
1
1
2
1
3
1
1
2
1
1
5BP0014485  
5BP0014478  
5BP0014470  
5BP0057273  
5BP0030064  
5BP0034265  
5BP0002265  
5BP0014488  
5BP0001174  
5BP0015230  
5BP0091384  
5BP0014490  
5BP0099978  
Stirrer, tumbling agitator  
Hitch, tumbling agitator  
Beam, tumbling agitator  
Washer fender Ø12 Z  
Nut PT M12-1.75 C6 TK Z  
Bolt HH M12-1.75x65 C8.8 Z P  
Washer flat Ø12 W  
Wheel, tumbling agitator  
Cotter pin Ø4x35  
Washer flat Ø08 W  
9
10  
11  
12  
Nut ES M08-1.25 Z TK  
Bolt HH M08-1.25x50 C8.8 Z P  
Tumbling agitator, complete;SS1036B, SS2036B, SS1067B,  
SS2067B (since 03/2011)  
-
PARTS MANUAL  
51  
FRONTIER  
03/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
DEFLECTOR (OPTION)  
OPERATOR’S MANUAL  
SS1023B, SS1036B, SS2036B  
Ref.  
1
2
3
4
Part #  
Description  
Deflector shield  
Deflector connection, left  
Deflector connection, right  
Adjustment knob M6x16  
Qty.  
5BP501653B  
5BP0214680  
5BP0114680  
5BP501631B  
5BP0099524  
1
1
1
2
-
Deflector, complete; SS1023B, SS1036B, SS2036B  
PARTS MANUAL  
52  
FRONTIER  
01/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
DEFLECTOR (OPTION)  
OPERATOR’S MANUAL  
SS1067B, SS2067B  
Ref.  
1
2
3
4
5
6
7
Part #  
Description  
Deflector shield  
Deflector connection  
Adjustment knob M8x15  
Bolt HH M08-1.25x30 C8.8 Z F  
Washer fender Ø8 Z  
Washer flat Ø8 W  
Nut ES M08-1.25 Z TK  
Qty.  
5BP0014501  
5BP0014505  
5BP501589B  
5BP0046543  
5BP0014514  
5BP0015230  
5BP0091384  
5BP0099638  
1
2
2
2
2
2
2
-
Deflector, complete; SS1067B, SS2067B  
PARTS MANUAL  
53  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FERTILIZER SPREADERS  
SIDEROW DISCHARGE (OPTION)  
OPERATOR’S MANUAL  
SS1067B, SS2067B  
Ref.  
1
2
3
4
5
6
7
8
Part #  
Description  
Half conveyor, left  
Half conveyor, right  
Baffle plate  
Conveyor attachment  
Conveyor bracket  
Bracket attachment plate, right  
Bracket attachment plate, left  
Bolt HH M08-1.25x25 C8.8 Z F  
Washer flat Ø8 W  
Nut ES M08-1.25 Z TK  
Adjustment knob M8x15  
Washer lock Ø8 Z  
Qty.  
1
1
1
1
2
1
1
8
16  
8
2
2
2
5BP503701B  
5BP503702B  
5BP503703B  
5BP503704B  
5BP503705B  
5BP503706B  
5BP503707B  
5BP0091446  
5BP0015230  
5BP0091384  
5BP501589B  
5BP0003144  
5BP0002034  
5BPAA4120  
9
10  
11  
12  
13  
Washer flat Ø10 W  
Siderow discharge, complete; SS1067B, SS2067B  
-
Note: Serial #’s with the XF prefix are subsequent to serial numbers with the BC prefix. For example: A  
reference to “serial # BC… 739197 & above” will also include all serial numbers with an XF prefix.  
PARTS MANUAL  
54  
FRONTIER  
06/2010  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use only original spare parts  
All rights reserved. It is unlawful to copy, reprint or use any of the information or details in this manual  
without the expressed written permission of the Company. Technical information provided in this  
manual is approximate, the Company reserves the right to modify or improve the models shown for  
technical or commercial purposes. Pictures in this manual do not necessarily show the machine as  
delivered.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual 5BP960376B  
Date 05/19/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  

John Deere Lawn Mower 5045E User Manual
JVC CD Player XL SV23GD User Manual
JVC Stereo System 0803AIMMDWJEM User Manual
Kenmore Dishwasher 4651332 User Manual
Kenmore Refrigerator 795775626 User Manual
Kenwood Car Video System DDX7039M User Manual
Kenwood Wheelchair 241E User Manual
Kidde Carbon Monoxide Alarm KN COB DP H User Manual
Kodak DVD Player DV 2500H User Manual
Kompernass Blender KH 498 User Manual