INSTALLATION & USER GUIDE
For High Performance
Home Theater Reproduction
from In-Wall Locations
RIGHT, LEFT, SURROUND AND
LST-RLS/CTR
Download from Www.Somanuals.com. All Manuals Search And Download.
CENTER CHANNEL IN-WALL LOUDSPEAKER
FEATURES: LST-RLS
FEATURES: LST-CTR
I Dual 5-1/4” mica filled polypropylene
woofers with butyl rubber surrounds
I Dual 5-1/4” magnetically shielded mica
filled polypropylene woofers with butyl
rubber surrounds
®
I 1” liquid cooled ElastoDynamic
dome tweeter
I 1” liquid cooled magnetically shielded
ElastoDynamic dome tweeter
®
I Front mounted bass and treble
cut switches (-3dB)
I Front mounted dialog enhancement
switch
I Configurable as a main or
surround speaker
I Front mounted treble cut switch (-3dB)
I Rigid braced ABS speaker baffle
I Moisture and UV resistant
I Rust proof aluminum grille
I Crossover mounted Off-Axis
compensation (OAC) switch
I Rigid braced ABS speaker baffle
I Moisture and UV resistant
I Rust proof aluminum grille
Installation friendly design:
I Suitable for painting
Installation friendly design:
I Connection terminals accept up to 12
gauge speaker wire
I Suitable for painting
IIncludes system mounting hardware for
I Connection terminals accept up to 12
New Construction or retrofit installations
gauge speaker wire
I Includes system mounting hardware for
New Construction or retrofit installations
PRODUCT OVERVIEW
Figure 1
New Construction Wings
Bracket
Frame
Speaker Baffle
IR Knockout (accommodates
JOBSITE IR-FMR IR Receiver)
Grille
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CONTENTS
TOOLS REQUIRED
I Speaker x 1
I Stud Locator (for existing construction)
I Drywall saw (for existing construction)
I Pencil (for existing construction)
I Cordless screwdriver with No2 Philips bit
I 1/8” Slotted screwdriver x 2
I Wire stripper
I Speaker frame x 1
I Speaker grille x 1
I Speaker bracket x 1
I Wings for new construction x 2
I #6 x 1-5/8” Philips head
drywall screws x 14
I Wire labels
I Speaker cutout template x 1
INSTALLATION
PREPARING FOR
INSTALLATION
Installation Existing
Construction:
If you are installing LST speakers into an
existing wall, take time to consider any
possible obstructions, which may be hidden
inside the wall: studs, electrical wiring,
telephone wiring, plumbing, AC or heating
conduit and ductwork.
1. Using your stud locator, identify the
location of the studs on each side of the
proposed speaker mounting location.
2. Mark their edges, using masking tape.
3. Repeat this process for the other
speakers.
Determine the best mounting locations
based on the room layout. Before cutting
any holes, make sure the area behind both
speakers is clear for installation. Speakers
provide the best coverage, when centered
in the wall. Choose a suitable mounting
height, and then line up both speakers
approximately the same distance from the
sidewall and ceiling boundaries.
4. You may have to adjust the speaker
mounting locations based on how
symmetrical the studs are located, in the
wall space.
5. Check for clearance using the following
method.
a. Drill a 1/4” pilot hole in the center of the
intended speaker location.
If you are installing the speakers into a new
construction wall, follow the above
recommendations and install the new
construction speaker bracket.
b. Cut a foot-long piece of coat hanger.
c. Bend the wire, creating a right angle,
leaving 4-1/4” at one end.
Label the speakers wires at the
amplifier location.
d. Poke the “L-shaped” wire into the pilot
hole and turn it in a complete circle,
checking for obstructions.
e. Push it into the wall cavity to make
sure you have approximately 4” of
depth.
f. If the coat hanger movement is
obstructed by anything, fill the hole(s)
with spackle and try another location
2
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Locate the cutout template.
13. Tightly twist the end of each wire until
no frayed ends remain.
7. Use a pencil and the cutout template to
trace the speaker outline in the desired
locations on the wall.
14. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal. Connect the positive
output from the amplifier to the red
terminal.
8. Use a drywall saw to cut along the
penciled line.
9. Slip the mounting bracket through the
opening and pull it toward you so that its
front edge slides into the hole and stops
in place.
15. Set the speaker configuration switches
on the rear of the speaker (see Setting
the Speaker Configuration Settings).
10. Attach the frame to the bracket by
screwing the frame to the bracket using
the supplied screws. NOTE: Do not over
tighten the screws, this will distort the
frame and the grille will not fit.
16. Install the speaker in the frame. Screw
the enclosed self-tapping screws into
the dimples of the speaker baffle as
shown in Figure 2.
17. Repeat steps 1-16 for each speaker
being installed.
11. The screws should pull the frame and
bracket together (sandwiching the
drywall) so that the frame is flush with
the wall surface.
18. After making tonal adjustments on all
speakers (see Setting the Speaker
Configuration Settings), install the grill
into the speaker.
12. Strip 1/4” of insulation from the end of
each wire.
Figure 2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation New Construction:
8. In unique situations where the bracket
must be located precisely next to a joist,
the bracket has “emergency” screw
holes located on its snap-on tabs. Break
away two of the outer mounting tabs on
the side you wish to affix, see Figure 3.
Notching the joist so the bracket lies
flush may be required.
The speaker brackets should be installed
prior to the drywall.
1. Attach the wings to the bracket by
snapping them into the sides of the
bracket. (See Figure 1). To shorten the
wings, break them along the scored lines.
2. The wings and brackets have centering
lines to simplify placement of the speaker.
9. Next, screw the bracket tab to the joist
using one of the supplied screws.
Important: Do not over-tighten the screw,
doing so could crack the bracket tab.
Level the bracket, then affix the other side
of the bracket assembly using the
supplied screws.
3. Use a tape measure to locate and center
the brackets in the ceiling.
4. Mark each speaker location with a
pencil.
5. Screw one side of the assembled bracket
with wings to the joist using one of the
supplied screws.
10. After the drywall is installed, cut a hole
in the drywall using the outside of the
circular bracket flange as a template.
6. Screw the other side of the bracket/wing
assembly to the joist. Two screws on
each side make for a very secure
installation.
11. Attach the frame to the bracket by
screwing the frame to the bracket using
the supplied screws. NOTE: Do not over
tighten the screws, this will distort the
frame and the grille will not fit.
7. Secure the wire to the bracket using the
bracket’s wire tie.
Figure 3
Break away two of the outer
mounting tabs on the side
you wish to affix.
Emergency
screw hole for
butting bracket
against
joist.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
12. The screws should pull the frame and
bracket together (sandwiching the
drywall) so that the frame is flush with
the wall surface.
LST-RLS Main/Surround Switch
The crossover on the back of the LST-RLS
enables you to configure the speaker for
best performance as either a front “main”
speaker or rear “surround” speaker. When
the LST-RLS is used as a surround speaker,
set the switch to the “Surround” position to
provide a diffuse sound field which provides
a more convincing illusion of sound all
around the listener. When configured as a
surround speaker, the orientation of the
tweeter is no longer critical.
13. Strip 1/4” of insulation from the end of
each wire.
14. Tightly twist the end of each wire until
no frayed ends remain.
15. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal. Connect the positive
output from the amplifier to the red
terminal.
Front Baffle Switches
LST-CTR Acoustic Fine Tuning
The front-mounted switches on the LST-CTR
enable the speaker to be optimized
regardless of positioning or room acoustics
by providing 3dB of Treble Cut and 3dB of
Dialog Enhancement. Start by listening to
the speaker in the normal mode (switch is in
the “out” position). If the sound seems to
have too much treble, depress the switch
labeled Treble Cut to reduce the amount of
high frequencies.
16. Set the speaker configuration switches
on the rear of the speaker (see Setting
the Speaker Configuration Settings).
17. Install the speaker in the frame. Screw
the enclosed self-tapping screws into
the dimples of the speaker baffle as
shown in Figure 2.
18. Repeat steps 1-17 for each speaker
being installed.
If you desire to make dialog more
pronounced, depress the switch labeled
Dialog Enhance.
19. After making tonal adjustments on all
speakers (see Setting the Speaker
Configuration Settings), install the grill
into the speaker.
LST-RLS Acoustic Fine Tuning
The front-mounted switches on the LST-RLS
also enable the speaker to be optimized
regardless of positioning or room acoustics.
They provide 3dB of Treble and Bass Cut
respectively. Start by listening to the
speaker in the normal mode (switch is in the
out position). If the sound seems to have too
much treble, depress the switch labeled
Treble Cut to reduce the amount of high
frequencies. If the sound has too much low
frequency output (because it is placed near
a corner perhaps) depress the switch
labeled Bass Cut.
SETTINGTHE SPEAKER
CONFIGURATION SETTINGS
Crossover Mounted Switches
LST-CTR OAC Switch
The crossover on the back of the LST-CTR
enables you to defeat the Off-Axis
Compensation (OAC) feature. Defeat OAC
when the speaker is mounted at ear level
directly in front of the primary listening
position, as would be the case when the
speaker is mounted behind a perforated
projection TV screen.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVAL OF GRILLE
Removing the Grille
OPERATION
Listening at Higher Volumes:
Listening at Higher Volumes:
If the grille is already installed, remove it by
using a bent paper clip or the tip of a
corkscrew and pulling it away from the
frame. See Figure 4.
It requires more power to achieve a
reasonable volume of sound in a large room
than it does in a small room. It is possible to
turn the volume so high that the amplifier
runs out of power. This creates “clipping”
distortion.
Clipping distortion makes treble sound
very harsh and unmusical. When you hear
harsh sounding treble from any good
speaker, turn the volume down
immediately! You are much less likely to
damage a speaker with a large amplifier
less likely to produce any clipping distortion.
Figure 4
PAINTINGTHE GRILLE
AND FRAME
Painting the Speaker Frame
The speakers must be removed prior to
painting the frames.
Painting the Grilles:
The grilles should be painted before they
are installed on the speakers. The best
results will be obtained by using a spray
gun or airless sprayer. Thin the paint, and
then apply several light coats. This
technique helps prevent clogging of grille
holes. Paint both sides of the grille to cover
all the white paint.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS: LST-RLS
Power handing:
10 – 150 watts
Frequency response:
45Hz-21kHz +/- 3dB
Impedance:
8 ohms
Dimensions:
8-1/4” x 14-1/2” outside dimension
7-1/8” x 13-1/4” hole cutout
3-1/8” deep when installed in 1/2” drywall
Warranty:
5 year limited
SPECIFICATIONS: LST-CTR
Power handing:
10 – 150 watts
Frequency response:
45Hz-21kHz +/- 3dB
Impedance:
8 ohms
Dimensions:
8-1/4” x 14-1/2” outside dimension
7-1/8” x 13-1/4” hole cutout
3-1/8” deep when installed in 1/2” drywall
Warranty:
5 year limited
7
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
A factory Return Authorization Number will
be sent to you. DO NOT RETURN ANY
UNIT WITHOUT FIRST RECEIVING
WRITTEN AUTHORIZATION AND
SHIPPING INSTRUCTIONS FROM
JOBSITE.
JobSite Systems (“JOBSITE”), a Niles
Audio Corporation company, warrants its
passive products (those not requiring AC or
battery power) to the original purchaser to
be free of manufacturing defects in material
and workmanship for a period of ten years
from date of purchase.
If the above conditions are met, the
purchaser’s sole remedy shall be to return
the product to JOBSITE, in which case
JOBSITE will repair or replace, at its sole
option, the defective product without
charge for parts or labor. JOBSITE will
return the unit repaired or replaced under
warranty by shipping it by its usual
shipping method from the factory (only) at
its expense within the United States of
America. THERE ARE NO OTHER
WARRANTIES, INCLUDING, WITHOUT
LIMITATION, EITHER EXPRESS OR
IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT
TO THE PRODUCT.
JOBSITE warrants its passive loudspeaker
products (those not requiring AC or battery
power) to the original purchaser to be free
of manufacturing defects in material and
workmanship for a period of five years
from date of purchase.
JOBSITE warrants its indoor/outdoor
loudspeaker products to the original
purchaser to be free of manufacturing
defects in material and workmanship for a
period of two years from date of purchase.
JOBSITE warrants its all weather rock
loudspeaker products to the original
purchaser to be free of manufacturing
defects in material and workmanship for a
period of five years from date of purchase.
REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE
CONSUMER/PURCHASER. JOBSITE SHALL
NOT BE RESPONSIBLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL
DAMAGES EXCEPT TO THE EXTENT
PROVIDED (OR PROHIBITED) BY
APPLICABLE LAW.
JOBSITE warrants its active products
(those requiring AC or battery power) to
the original purchaser to be free of
manufacturing defects in material and
workmanship for a period of two years
from date of purchase.
This Warranty is subject to the following
additional conditions and limitations. The
Warranty is void and inapplicable if
JOBSITE deems that the product has been
used or handled other than in accordance
with the instructions provided by the
manufacturer, including, but not limited to,
damage caused by accident, mishandling,
improper installation, abuse, negligence, or
normal wear and tear, or any defect
caused by repair to the product other than
by JOBSITE or an authorized JOBSITE
wholesale distributor.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation may not
apply to you. This warranty gives you
specific legal rights, and you may also
have other rights, which vary from state to
state.
For the name of the nearest authorized
JOBSITE wholesale distributor, contact:
JobSite Systems, a Niles Audio
Corporation company
To obtain warranty service, you must write
to JOBSITE: Include your name, address,
telephone number, model number and
serial number of your unit, and a brief
description of the problem.
P.O. Box 160818, Miami, Florida 33116
8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
JOBSITE SYSTEMS
12331 S.W. 130 STREET, MIAMI, FLORIDA 33186
P (866) 4JB-SITE (866-452-7483) – F (305) 238-0185
WWW.JOBSITESYSTEMS.COM
JobSite Systems, a Niles Audio Corporation company, 12331 S.W. 130 Street, Miami, Fl 33186. ©2004 Niles Audio Corporation. JobSite, Pure
Custom, ElastoDynamic and Niles are registered trademarks of Niles Audio Corporation and the JobSite Logo is a trademark of Niles Audio
Corporation. All other trademarks are the property of their respective owners. Some JobSite products (or components thereof) are manufac-
tured under one or more U.S. Patents, foreign equivalents and/or pending patents (see product for details). Because we constantly strive to
improve our products, JobSite reserves the right to change product specifications, descriptions, and prices without notice. The technical and
other specifications of information contained herein are not intended to set forth all technical and other specifications of JobSite products.
Additional information can be obtained at www.JobSitesystems.com or by calling JobSite at 866-452-7483. Printed in China. 11/04 DS00388ACN
Download from Www.Somanuals.com. All Manuals Search And Download.
|