Jet Tools Saw JTAS 10 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

This Manual is Bookmarked

Owner's Manual

XACTA^®Fence II Commercial 30/50

WMH TOOL GROUP

2420 Vantage Drive

Elgin, Illinois 60124

Ph.: 800-274-6848

Part No. M-708950Z

Revision J 01/07

www.wmhtoolgroup.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty and Service

WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our

Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of

these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or

perform routine maintenance and major repair on your JET^®tools. For the name of an Authorized Service Center in

your area call 1-800-274-6848.

MORE INFORMATION

WMH Tool Group is consistently adding new products to the line. For complete, up-to-date product information, check

with your local WMH Tool Group distributor, or visit jettools.com.

WARRANTY

JET products carry a limited warranty which varies in duration based upon the product (MW stands for Metalworking,

WW stands for Woodworking).

WHAT IS COVERED?

This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools,

abrasives and other consumables are excluded from warranty coverage.

WHO IS COVERED?

This warranty covers only the initial purchaser of the product.

WHAT IS THE PERIOD OF COVERAGE?

The general JET warranty lasts for the time period specified in the product literature of each product.

WHAT IS NOT COVERED?

Five Year and Lifetime Warranties do not cover products used for commercial, industrial or educational purposes.

Products with Five Year or Lifetime Warranties that are used for commercial, industrial or education purposes revert

to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence

or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.

HOW TO GET SERVICE

The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name

of the location nearest you, please call 1-800-274-6848.

You must provide proof of initial purchase date and an explanation of the complaint must accompany the

merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price,

at our option. We will return the repaired product or replacement at our expense unless it is determined by us that

there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will,

at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be

responsible for the shipping and handling costs of the return.

HOW STATE LAW APPLIES

This warranty gives you specific legal rights; you may also have other rights which vary from state to state.

LIMITATIONS ON THIS WARRANTY

WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR

EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND

FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED

WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

WMH TOOL GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY,

OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE

OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

WMH Tool Group sells through distributors only. The specifications in WMH catalogs are given as general information

and are not binding. Members of WMH Tool Group reserve the right to effect at any time, without prior notice, those

alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

JET^®branded products are not sold in Canada by WMH Tool Group.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Warranty and Service....................................................................................................................................2

Table of Contents..........................................................................................................................................3

Warnings .......................................................................................................................................................4

Ordering Replacement Parts.........................................................................................................................5

Unpacking .....................................................................................................................................................6

Contents of the Shipping Containers.........................................................................................................6

Tools Required for Assembly & Adjustment..............................................................................................6

Installation.....................................................................................................................................................7

Tools required............................................................................................................................................7

Front Rail Installation.................................................................................................................................7

Switch Installation......................................................................................................................................7

Back Rail Installation .................................................................................................................................8

Wooden Extension Table..............................................................................................................................9

Tools required............................................................................................................................................9

Installation .................................................................................................................................................9

Guide Tube .................................................................................................................................................10

XACTA Fence .............................................................................................................................................11

Leveling Fence to the Saw Table ........................................................................................................11

Adjusting Fence Parallel to the Miter Slot............................................................................................12

Clamping Pressure ..............................................................................................................................12

90° to the Table....................................................................................................................................12

Cursor Adjustment ...............................................................................................................................12

Parts for the XACTA Fence II Commercial 30/50.......................................................................................13

Parts for the XACTA Fence II Rail Assembly..............................................................................................14

Parts for the XACTA Fence II Leg Assembly..............................................................................................15

Appendix – Extension Table Dimensions ...................................................................................................15

The specifications in this manual are given as general information and are not binding. WMH Tool Group

reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings,

and accessory equipment deemed necessary for any reason whatsoever.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings

1. Read and understand the entire owners manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with

all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. The Table Saw on which the XACTA Fence II is used is designed and intended for use by properly

trained and experienced personnel only. If you are not familiar with the proper and safe operation of a

Table Saw, do not use until proper training and knowledge have been obtained.

5. Do not use this Table Saw on which the XACTA Fence II is used for other than its intended use. If

used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself

harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields while using this Table Saw. Everyday eyeglasses

only have impact resistant lenses; they are not safety glasses.

7. Before operating the Table Saw, remove tie, rings, watches and other jewelry, and roll sleeves up

past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor

strips are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities

contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

•

Lead from lead based paint.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically treated lumber.

10. Your risk of exposure varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area and work with approved safety

equipment, such as face or dust masks that are specifically designed to filter out microscopic

particles.

11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

12. Make certain the switch is in the OFF position before connecting the machine to the power supply.

13. Make certain the machine is properly grounded.

14. Make all machine adjustments or maintenance with the machine unplugged from the power source.

15. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting

wrenches are removed from the machine before turning it on.

16. Keep safety guards in place at all times when the machine is in use. If removed for maintenance

purposes, use extreme caution and replace the guards immediately.

17. Make sure the Table Saw is firmly secured to the floor or bench before use.

18. Check damaged parts. Before further use of the machine, a guard or other part that is damaged

should be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other part that is damaged should

be properly repaired or replaced.

19. Provide for adequate space surrounding work area and non-glare, overhead lighting.

20. Keep the floor around the machine clean and free of scrap material, oil and grease.

21. Keep visitors a safe distance from the work area. Keep children away.

Download from Www.Somanuals.com. All Manuals Search And Download.

22. Make your workshop child proof with padlocks, master switches or by removing starter keys.

23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are

careless acts that can result in serious injury.

24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do

not overreach or use excessive force to perform any machine operation.

25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for

which it was not designed. The right tool will do the job better and safer.

26. Use recommended accessories; improper accessories may be hazardous.

27. Maintain tools with care. Keep saw blades sharp and clean for the best and safest performance.

Follow instructions for lubricating and changing accessories.

28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do

not use your hands.

29. Do not stand on the machine. Serious injury could occur if the machine tips over.

30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

31. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

Ordering Replacement Parts

To order parts or reach our service department, call 1-800-274-6848 between 7:30 a.m. and 5:30 p.m.

(CST), Monday through Friday. Having the Model Number and Serial Number of your machine available

when you call will allow us to serve you quickly and accurately.

Download from Www.Somanuals.com. All Manuals Search And Download.

Unpacking

Open shipping cartons and check that all parts are

intact. Report any damage immediately to your

distributor. Read the instruction manual thoroughly

for assembly, alignment, and maintenance

instructions.

Contents of the Shipping Containers

XACTA Fence II

Front Rail

Rear Rail

Guide Rail

Black Plastic End Caps

Hardware Package

Owner’s Manual

Warranty Registration Card

The contents of the hardware bag are drawn full

scale in Figure 1.

Note 1: Quantities may vary depending upon

whether you purchased the short rail or long rail.

Note 2: If the optional wooden extension table is

not used, there will be extra hardware.

Tools Required for Assembly &

Adjustment

#3 Cross Point Screwdriver

7/16” Wrench

1/2" Wrench

Combination Square & Straight Edge

Electric Drill

1/4”, 3/16” Drill Bits

4”-6” C-Clamps

1/4”, 3/16” Allen Wrenches

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Tools required

7/16" and 1/2" wrenches

Cross point screwdriver

3/16" hex wrench

Adjustable square

Hammer (or rubber mallet)

Straight edge

The following instructions are for installing the

XACTA Fence II and Rail System on JET Models

JTAS-10, JTAS-12 and XACTA^®Saw Deluxe

series table saws. The rails should bolt up to the

JET saw without any drilling.

Front Rail Installation

Referring to Figures 1 and 2:

Figure 1

1. Identify the front rail (E), which is

2-1/2" x 2-1/2" with notches on one side and

countersunk mounting holes on the other side.

2. Lightly secure the front rail (E) to the table (G)

and extension wings (F) with four each 1/4 x 1-

1/2 flat head screws (A), 1/4” flat washers (B),

1/4” lock washers (C) and 1/4” hex nuts (D).

Tighten just enough to hold the rail next to the

table but keep loose enough to allow height

adjustment.

The front rail must be 9/16" down from the table

top in order to clear the miter gauge slot. This

measurement is critical.

3. Place an adjustable square on the table as

shown in Figure 3.

Figure 2

4. Check the height of the front rail at several

locations along the surface of the saw table.

The front rail must be parallel with the table

top.

When the front rail has been correctly positioned:

5. Use a #3 cross point screwdriver and 7/16"

wrench to tighten all mounting screws

securely. However, do not tighten hardware for

the left extension table (shown in F, Fig. 1).

The hardware that secures the left extension

table should be left loose to accommodate the

switch installation (below).

Switch Installation

At this time refer to your JTAS-10, JTAS-12 or

XACTA^®Saw manual and attach the switch as

described in the Switch Installation section. The

switch should be attached before the guide tube

installation covered later in this manual.

Figure 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Back Rail Installation

1. Locate the back rail which is 2" x 2" with holes

running along one side only. The height of the

back rail when attached to the saw is not

critical.

2. Align the holes in the back rail to the holes in

the table top, as shown in Figure 4.

Figure 4

3. Secure the back rail to the pre-tapped holes in

the saw table (B, C, Fig. 4) with two 5/16 x 3/4

hex cap screws and two 5/16 flat washers, as

shown in Figure 5. Tighten screws securely

with a 1/2" wrench.

Figure 5

4. Secure the back rail at A and D (in Figure 4) to

each extension wing with a 1/4 x 1-1/2 hex cap

screw, two 1/4” flat washers, a 1/4” lock

washer, and a 1/4” hex nut as shown in

Figure 6.

5. Tighten nuts.

Figure 6

Important: If you are installing an optional wood

extension table on your saw, it should be installed

first before mounting the guide tube. This will

prevent having to mount and align the guide tube

twice.

If you are not mounting an optional wood table,

proceed to Guide Tube section.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wooden Extension Table

The wooden extension table is an optional

accessory.

Tools required

Electric drill

Cross point screwdriver

7/16" and 1/2" wrenches

Four clamps

Straight edge

Hammer (or rubber mallet)

Figure 7

Installation

The optional wood extension table (including the

optional router table) sits flush against the saw

table and along the inside of the rails. The JET

logo (or warning label on the router table) should

face outward. The extension table is not bolted to

the saw table, it is bolted only to the rails.

The extension table and saw table must be aligned

properly so the XACTA Fence II will slide smoothly

from one to the other.

1. Place the extension table between the rails

and up against the saw table, leaving the

extension table raised just slightly above the

saw table. Clamp the extension table to the

front and back rails as shown in Figure 7.

Clamping pressure should be enough to

secure the table yet allow minor adjustments.

Figure 8

2. Use a hammer and block of wood (or a rubber

mallet) to tap the extension table up flush

against the cast iron saw table (Figure 7).

Then tap down the extension table at various

points along its edge where it meets the saw

table, until it is level with the saw table

(Figure 8). As one part of the edge becomes

level with the table, tighten the clamp on that

side. Then move to the other side and repeat,

until the full length of the edge is level with the

saw table. Lay a straight edge across both

extension table and saw table to ensure proper

leveling.

Figure 9

When extension table is properly aligned, holes

need to be drilled into the wood table using the

holes in the rails as your guide (Figure 9). You may

wish to drill 3/32" pilot holes first.

3. Drill 1/4" holes into the front edge of the table

using the holes in the front rail as a guide. Drill

1/4" holes into the back edge of the table using

the holes in the back rail as a guide.

4. Install three 1/4 x 1-1/2 flat head screws, three

1/4 flat washers, and three 1/4 hex nuts into

the holes in the front edge of extension table

Figure 10

Download from Www.Somanuals.com. All Manuals Search And Download.

as shown in Figure 10. Finger tighten only.

5. Install three 1/4-20 x 1-1/2 hex cap screws,

three 1/4 flat washers, and three 1/4 nuts into

the holes in the rear edge of extension table as

shown in Figure 11. Finger-tighten only.

6. Re-check the table for alignment, make further

adjustments if necessary, then tighten all

screws and nuts.

Figure 11

7. Mount the two legs to the inside corners of the

extension table as shown in Figure 12. Secure

with the eight screws provided.

Note: If you are using a mobile base under your

saw, you may need to shift the placement of the

legs so they rest properly upon the shelves of the

base.

8. Adjust

the

footpads

the

legs

counterclockwise until they reach the floor,

then tighten the nut.

Figure 12

Guide Tube

Important: Before proceeding with the guide tube

installation, the table saw switch should already be

installed. If not, refer to the Switch Installation

section in your JTAS-10, JTAS-12 or XACTA^®Saw

manual.

Referring to Figure 13:

The guide tube (A) is placed on top of the front rail

(B) and is mounted with the scale facing toward

the operator.

1. Align the holes in the bottom of the guide tube

with the holes in the front rail. When properly

positioned the guide tube should extend

beyond the front rail about 6" in both

directions.

Figure 13

2. Fasten the guide tube (A) to the rail (B) from

beneath, with seven 1/4-20 x 3/4 hex head

screws (B), seven 1/4" lock washers (F) and

seven 1/4" flat washers (G). Finger tighten

only.

3. Tighten all screws with a 7/16" wrench.

Download from Www.Somanuals.com. All Manuals Search And Download.

XACTA Fence

Screw the lock lever knob into the threaded handle

on the XACTA Fence II as shown in Figure 14.

The lock lever has three functional positions as

shown in Figure 15:

•

The upright position permits mounting and

removal of fence from the saw.

The unlock position permits easy fence

positioning.

The lower position locks the fence to the

front rail. The cam handle should be

pushed down firmly against the pin.

Figure 14

Leveling Fence to the Saw Table

1. Place the fence on the table and lock it.

2. View the fence from the left side of the saw

(Figure 16). Look for the space between the

table and the fence bottom to be equal along

the entire length of the fence (A, B, Fig. 16).

Figure 15

If adjustment is necessary:

3. Unlock the fence.

Fence Side Plate

Table Top

4. Using a 10mm wrench, loosen the lock nut that

secures the foot adjustment (C, Fig. 16)

Back Rail

Guide Tube

Front Rail

5. Rotate the foot, retracting it such that it does

not come in contact with the back rail (Fig. 16).

Figure 16

6. Raise or lower two nylon adjustment screws

(D, Fig. 17) the same number of turns until the

space between the bottom of the fence and the

table is the same. Care must be taken to raise

or lower the fence on each side equally or the

fence may not be 90° to the table after the

height adjustment is performed.

When the space at points A and B (Fig. 16) are the

same:

7. Extend the foot (C, Fig. 16) by rotating it until it

just comes in contact with the back rail.

8. Tighten the lock nut to secure the foot,

preventing it from further rotation.

Figure 17

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting Fence Parallel to the Miter Slot

1. Place the fence next to the outside edge of the

right miter slot and lock it.

2. The fence should be even with the miter slot

from front to back.

3. If the fence is not even along the length of the

miter slot, unlock the fence, remove it and turn

upside down.

4. Adjust one of the two setscrews (A, Fig. 18)

until the fence is even with the miter slot edge

along its entire length when locked.

Note: You may need to re-adjust the clamping

pressure after aligning the fence.

Clamping Pressure

The XACTA Fence II has been adjusted at the

factory to lock securely when the lock handle is

pushed down. If adjustment is needed:

Figure 18

1. Unlock the fence.

2. Remove the fence from the guide rail.

3. Turn the fence over.

4. Adjust each of the two setscrews (A, Fig. 18)

exactly the same number of rotations until the

fence is held securely when the lock handle is

pushed down.

90° to the Table

1. Place the fence on the saw table and lock it.

2. Place a square (A, Fig. 19) on the table next to

the fence. The fence should be 90° to the

table.

3. If adjustment is necessary, unlock the fence,

and turn one of the two nylon adjustment

screws (B, Fig. 19) until the fence is 90° to the

table.

4. Lock the fence and check the adjustment

again.

Figure 19

Cursor Adjustment

1. Disconnect the table saw from the power

source.

Note: If the cursor does not have enough travel to

give the correct measurement loosen the guide rail

and adjust as needed. If you still do not get the

correct measurement loosen the front rail and

adjust as needed. If you have to adjust the front rail

you will need to go through the front rail assembly

instructions again.

2. Raise the saw blade above the tabletop.

3. Unlock the fence and slide it to approximately

four inches from the saw blade.

4. Lock the fence.

5. Measure the distance between the saw blade

and the inside of the fence.

This adjustment must be checked whenever a

different blade is installed.

6. Adjust the cursor (C, Fig. 19) to read the

distance just measured and tighten the cursor

assembly to the fence.

After installing the XACTA Fence II press the black

plastic end caps into the openings of the guide rail.

There is also an end cap for the fence, but this

should already be installed.

7. Take a test cut and confirm the adjustment is

correct.

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts for the XACTA Fence II Commercial 30/50

Index No. Part No.

Description

Size

Qty

1 ...............XF2-101 ...................Left Side Plate...................................................... .................................... 1

2 ...............XF2-102 ...................Fence Body Assembly ......................................... .................................... 1

3 ...............XF2-103 ...................Tube Cover .......................................................... .................................... 1

4 ...............XF2-104 ...................Right Side Plate ................................................... .................................... 1

5 ...............TS-0640071 .............Lock Nut...............................................................1/4”-20....................... 10

6 ...............TS-0271031 .............Set Screw.............................................................3/8”-16 x 3/8” .............. 2

7 ...............3575081...................Fluoroway Pad..................................................... .................................... 2

8 ...............XF2-108 ...................Pad....................................................................... .................................... 1

9 ...............TS-0151011 .............Carriage Bolt........................................................1/4”-20 x 3/4” ............ 10

10 .............TS-081D022.............Pan Head Machine Screw ...................................10-32 x 3/8”................. 2

11 .............TS-0680021 .............Flat Washer..........................................................1/4”.............................. 2

12 .............TS-081D021.............Flat Head Machine Screw....................................10-32 x 3/8”................. 2

13 .............800708950 D ...........Cursor .................................................................. .................................... 1

14 .............800708950 C ...........Cursor Bracket..................................................... .................................... 1

15 .............TS-0640071 .............Lock Nut...............................................................1/4”-20......................... 1

16 .............TS-0640091 .............Lock Nut...............................................................3/8”-16......................... 1

17 .............XF2-117 ...................Spring Pin.............................................................4mm x 28.................... 1

18 .............6813042...................Compression Spring ............................................ .................................... 1

19 .............TS-0151041 .............Carriage Bolt........................................................1/4”-20 x 1-1/2” ........... 1

20 .............TS-0160021 .............Carriage Bolt........................................................3/8”-16 x 1-1/2” ........... 1

21 .............3215301...................Foot Cam ............................................................. .................................... 1

22 .............3076232...................Lock Cam............................................................. .................................... 1

23 .............6430055...................Knob w/stud ......................................................... .................................... 1

24 .............XF-5 .........................Nylon Adjustment Screw...................................... .................................... 2

25 .............TS-0680021 .............Flat Washer..........................................................1/4”.............................. 2

26 .............TS-0560081 .............Hex Nut ................................................................10-32........................... 2

27 .............XF2-127 ...................XCTA Fence Label............................................... .................................... 1

28 .............XF2-128 ...................Instruction Label................................................... .................................... 1

29 .............XF2-129 ...................JET Label............................................................. .................................... 1

30 .............XF2-130 ...................Foot Pad Holder................................................... .................................... 1

31 .............TS-0207061 .............Socket Head Cap Screw......................................1/4”-20 x 1” ................. 2

32 .............TS-0561011 .............Hex Nut ................................................................1/4”-20......................... 1

33 .............XF2-133 ...................Foot Pad............................................................... .................................... 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts for the XACTA Fence II Rail Assembly

Index No. Part No.

Description

Size

Qty

1 ...............XF2-201 ...................Front Rail (50”)..................................................... .................................... 1

.................XF2-201A.................Front Rail (30”)..................................................... .................................... 1

2 ...............TS-081F081.............Flat Head Screw ..................................................1/4”-20 x 1-1/2” ........... 7

3 ...............TS-0680021 .............Flat Washer..........................................................1/4”............................ 24

4 ...............TS-0720071 .............Lock Washer........................................................1/4”............................ 19

5 ...............TS-0561011 .............Hex Nut ................................................................1/4”-20....................... 12

6 ...............TS-0050031 .............Hex Cap Screw....................................................1/4”-20 x 3/4” .............. 7

7 ...............XF2-207 ...................Scale (50”)............................................................ .................................... 1

.................XF2-207A.................Scale (30”) ........................................................... .................................... 1

8 ...............XF2-208 ...................Guide Rail (50”).................................................... .................................... 1

.................XF2-208A.................Guide Rail (30”).................................................... .................................... 1

9 ...............XF2-209 ...................Rear Rail (50”) ..................................................... .................................... 1

.................XF2-209A.................Rear Rail (30”) ..................................................... .................................... 1

10 .............XF2-210 ...................Guide cover.......................................................... .................................... 2

11 .............TS-0081031 .............Hex Cap Screw....................................................5/16”-18 x 3/4” ............ 2

12 .............TS-0050071 .............Hex Cap Screw....................................................1/4” -20 x 1-1/2” .......... 5

13 .............TS-0680031 .............Flat Washer..........................................................5/16”............................ 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts for the XACTA Fence II Leg Assembly

Index No. Part No.

Description

Size

Qty

1 ...............XF2-301 ...................Leg ....................................................................... .................................... 2

2 ...............TS-0561031 .............Hex Nut ................................................................3/8”-16......................... 2

3 ...............XF2-303 ...................Adjusting foot ....................................................... .................................... 2

4 ...............TS-1533052 .............Machine Screw ....................................................M5×16......................... 8

Appendix – Extension Table Dimensions

The dimensions below are provided if you plan to build your own extension table instead of purchasing

one that is available through JET.

Download from Www.Somanuals.com. All Manuals Search And Download.

WMH Tool Group

2420 Vantage Drive

Elgin, Illinois 60124

Phone: 800-274-6848

www.wmhtoolgroup.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Infinity Speaker TSS STAND4000 User Manual
Ingersoll Rand Water Pump 650453 X User Manual
Insignia Flat Panel Television NS LCD19W 09 User Manual
JVC Flat Panel Television 0607TNH II IM User Manual
JVC VCR HR A230E User Manual
Kalamazoo Outdoor Gourmet Oven Pizza Oven User Manual
Kalorik Pet Fence PPG 26914 User Manual
Kenmore Refrigerator 25331115308 User Manual
KitchenAid Trash Compactor 9871780C User Manual
Kodak Scanner A 61003 User Manual