OWNER'S MANUAL
JOVS-10 Oscillating Spindle Sander
WMH TOOL GROUP
Consumer/Light Industrial Products Division
P.O. BOX 1349
Auburn, WA 98071-1349
Ph: 1-800-274-6848 Fax: 1-800-274-6840
E-mail: [email protected]
M-708411 11/02
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Wear eye protection.
Always keep guards in place and in proper operating condition. Do not operate the machine
without the guards for any reason.
This sander is intended to be used with wood and wood products only. Use of this sander and a
dust collector with metal products is a potential fire hazard.
Support the workpiece adequately at all times during operation; maintain control of the work at all
times.
This sander is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a sander, do not use until proper
training and knowledge has been obtained.
•
REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and
adjusting wrenches are removed from the machine before turning it on.
•
•
KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
•
•
•
KEEP CHILDREN AWAY. All visitors should be kept a safe distance from the work area.
MAKE THE WORKSHOP KIDPROOF with padlocks, master swatches, or by removing starter keys.
DON’T FORCE THE MACHINE. It will do the job better and safer at the rate for which it was
designed.
•
•
USE THE RIGHT TOOL. Don’t force a machine or attachment to do a job for which it was not
designed.
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your machine will
draw. An undersized cord will cause a drop in the line voltage resulting in power loss and
overheating. The table following shows the correct size to use depending on the cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge
number, the heavier the cord.
Volts
120V
Total Length of Cord in Feet
25 50
AWG
16
14
•
•
WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.
•
•
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position
before plugging in.
•
USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not
recommended by JET may cause hazards or risk of injury to persons.
•
•
NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped.
CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function - check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
•
•
NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the
machine until it comes to a complete stop.
SOME DUST CREATED by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
•
Your risk from those exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specifically designed to filter out microscopic particles
•
•
•
•
•
DO NOT operate tool while under the influence of drugs, alcohol or any medication.
AVOID kickback by sanding in accordance with directional arrows.
DO NOT sand pieces of material that are too small to be safely supported.
WHEN sanding a large workpiece, provide additional support at table height.
ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident
Prevention Manual for Industrial Operations and also in the safety Data Sheets provided by the NSC.
Please also refer to the American National Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
•
SAVE THESE INSTRUCTIONS refer to them often and use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your sander is ready to run at 115 volt operation. This sander, when wired
for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated
in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may be used to connect
this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not available. The
temporary adapter should only be used until a properly grounded outlet can be installed by a qualified
electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab,
extending from the adapter, must be connected to a permanent ground such as a properly grounded
outlet box, as shown in (B).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
JOVS-10
Stock Number................................................................................................................................ 708411
Table Size ..............................................................................................................................24”W x 24”L
Table Tilt (down)...................................................................................................................................45°
Dust Chute Diameter ..............................................................................................................................4”
Spindle Speed (RPM) ....................................................................................................................... 1,725
Oscillations Per Minute ..........................................................................................................................75
Length of Oscillation .........................................................................................................................1-1/2”
Motor (TEFC)..............................................................................................................................1HP, 1Ph
................................................................................................................................................. 115V Only
Net Weight (approx.).....................................................................................................................298 Lbs.
Table of Contents
Page No.
Warranty..................................................................................................................................................2
Warnings..............................................................................................................................................3-4
Grounding Instructions.............................................................................................................................5
115V Operation .......................................................................................................................................5
Specifications ..........................................................................................................................................6
Table of Contents ....................................................................................................................................6
Contents of the Shipping Container..........................................................................................................7
Tools Required for Assembly & Adjustments............................................................................................7
Unpacking ...............................................................................................................................................7
Mounting Sanding Sleeves ......................................................................................................................8
Installing Sanding Assemblies..................................................................................................................8
Removing Sanding Assemblies................................................................................................................8
Table Insert .............................................................................................................................................9
Sanding Assembly 90° to Table ...............................................................................................................9
Replacing Sanding Sleeves ...................................................................................................................10
Dust Collection ......................................................................................................................................10
Maintenance..........................................................................................................................................10
Troubleshooting.....................................................................................................................................11
Breakdown and Parts List .................................................................................................................12-17
Wiring Diagram......................................................................................................................................18
The specifications in this manual are given as general information and are not binding. The WMH Tool
Group reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Container
1. Sander
3. Table Insert Rings
2. Spindle Wrenches
1. 2mm Hex Wrench
10 Removable Spindles
1/4” x 5” Steel and Sanding Sleeve
3/8” x 6” Steel and Sanding Sleeve
1/2” x 6” Steel and Sanding Sleeve
5/8” x 6” Steel and Sanding Sleeve
3/4” x 9” Steel and Sanding Sleeve
1” x 9” Rubber and Sanding Sleeve
1-1/2” x 9” Rubber and Sanding Sleeve
2” x 9” Rubber and Sanding Sleeve
3” x 9” Rubber and Sanding Sleeve
4” x 9” Rubber and Sanding Sleeve
1
1
Owner's Manual
Warranty Card
Tools Required for Assembly &
Adjustments
1. 26mm Wrench or Large Adjustable Wrench
1. 6mm Hex Wrench
1. Square
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the sander!
Failure to comply may cause serious injury!
Unpacking
1. Remove all contents from shipping carton.
2. Report any damage to your distributor.
3. Do not discard any shipping material until
the sander has been assembled and is
running properly.
4. With help from another person move the
sander off of the pallet and into the desired
position.
5. Remove the protective coating found on the
table with a putty knife and a cleaning
solvent that will not damage painted
surfaces.
Note: Now is a perfect time to set your sander
up on a mobile base. It will make life easier in
the woodshop. JET has a Heavy Duty Universal
Mobile Base that will fit this sander. JET also
has a variety of Dust Collectors and Air Filtration
Units that will work nicely with your new sander.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Sanding Sleeves
1. Thoroughly clean the arbors (A, Fig. 1) on all
of the spindle assemblies. Also clean the
arbor housing on the sander.
2. Slip the sanding sleeve (B, Fig. 1) over the
spindle and hold in place by tightening the
set screw (C, Fig. 1) with the supplied 2mm
hex wrench.
3. Repeat for all of the steel spindle
assemblies.
4. To protect the sanding assemblies place
them in the holders found on the sides of the
sander, see Figure 2.
Installing Sanding Assemblies
WARNING
Disconnect the sander from the power
source when installing or removing sanding
assemblies.
Failure to comply may cause serious injury!
1. Thoroughly clean the arbor and arbor
housing before installing the sanding
assemblies.
2. Thread the arbor (A, Fig. 3) into the arbor
housing (B, Fig. 3).
3. Use the provided wrenches to hold the lower
arbor housing nut (C, Fig. 3) while turning
the arbor nut (D, Fig. 3) clockwise.
Removing Sanding Assemblies
1. Disconnect the sander form the power
source, unplug.
2. Use the provided wrenches to hold the
upper arbor housing nut (E, Fig. 3) while
turning the arbor nut (D, Fig. 3) counter-
clockwise.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Insert
1. Disconnect the sander form the power
source, unplug.
2. Choose the insert (A, Fig. 4) that most
closely matches the diameter of the sanding
drum.
3. Line up the notch in the insert with the
spring pin in the table (B, Fig. 4), and press
in place.
4. Remove the insert by pressing up from
underneath. Note: Keep the opening in the
table clean so that the insert can be easily
put in place, and removed.
Sanding Assembly 90° to Table
1. Loosen the lock knobs (C, Fig. 5) on
trunnions and position the table so that it
rests against the 90° stop (D, Fig. 6).
Tighten lock knobs.
2. Place a square (E, Fig. 5) on the working
side of the table, and make sure the sanding
drum is perpendicular to the table.
3. If an adjustment needs to be made loosen
the hex nut (F, Fig. 6).
4. Loosen lock knobs.
5. Rotate the 90° stop in the appropriate
direction until the table rests 90° to the
sanding drum.
6. Tighten the hex nut while holding the stop.
7. Adjust pointer (G, Fig. 6) so that it indicates
the “0” position on the scale.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Sanding Sleeves
1. Loosen hex nut (A, Fig. 7) with a 26mm
wrench, or large adjustable wrench.
2. Slide the sanding sleeve (B, Fig. 7) off the
drum and replace with a new sanding
sleeve. Note: If the sanding sleeve is not
easily removed cut the sleeve off and clean
the drum before reinstalling a new sleeve.
3. If you are replacing the sanding sleeves on
the steel spindles loosen the set screw
found on the arbor nut.
4. Remove sanding sleeve from the spindle
and replace with a new sanding sleeve.
Note: If the sanding sleeve is not easily
removed cut the sleeve off and clean the
drum before reinstalling a new sleeve.
5. Tighten the set screw.
Dust Collection
In order to collect wood dust; attach a dust
collection hose to the dust port. JET has a
variety of dust collectors, air filtration units,
hoses and adaptors, etc. that will work nicely
with your new sander. Contact your local JET
Distributor for more information.
Maintenance
The manufacturer recommends replacing the 90
SAE gear lube at 800 hours of use.
1. Open the door on the back side of the
machine to access the drain plug (C, Fig. 8).
Use a 6mm hex wrench to remove the drain
plug.
2. Refill oil through the oil cap (D, Fig. 9). The
oil capacity is two quarts.
3. The oil sight glass (E, Fig. 8) should read
between the “high” and “low” marks.
Keep the machine and all attachments clean.
All bearings are permanently lubricated and
require no further service.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Possible Cause
Trouble
Solution
1. Sander unplugged from wall
or motor
1. Check all plug connections
2. Replace fuse or reset circuit
breaker
2. Fuse blown or circuit breaker
tripped
Sander will not start
3. Replace cord
3. Cord damaged
4. Replace starting capacitor
4. Starting capacitor bad
1. Extension cord too light or
too long
1. Replace with adequate size
and length cord
Sanding drum does not come
up to speed
2. Low current
2. Contact a qualified electrician
1. Stand or base on uneven
surface
1. Adjust stand or base so that
it rests evenly on the floor
Machine vibrates excessively
Sanded edge not square
1. Table not square to sanding
drum
1. Use a square to adjust table
to sanding drum
1. Use coarser grit for stock
removal and fine grit for
finish sanding.
1. Wrong grit sanding sleeve
2. Feed pressure too great
Sanding marks on wood
2. Never force workpiece
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Breakdown for the JET Oscillating Spindle Sander
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the JET JOVS-10
Oscillating Spindle Sander
Index Part
No. No.
Description
Size
Qty.
7..........OVS10-007.................. Power Cord ........................................... ...............................................1
11........KEY5525...................... Key........................................................ ...............................................1
18........OVS10-18.................... Oil Indicator ........................................... ...............................................1
20........OS-30628 .................... Oil Seal.................................................. ...............................................1
21........BB-6206ZZ................... Ball Bearing...........................................6206ZZ ...................................1
22........OVS10-022.................. C-Ring...................................................RA63.......................................1
22A......OVS10-022A................ C-Ring...................................................RA62.......................................1
26........OVS10-026.................. Sleeve................................................... ...............................................1
27........OVS10-027.................. Guide Rail Shaft..................................... ...............................................1
28........BB-6205ZZ................... Ball Bearing...........................................6205LU ...................................2
29........OVS10-029.................. Locking Nut ........................................... ...............................................1
30........OVS10-030.................. Worm..................................................... ...............................................1
31........OVS10-031.................. Spring Pin..............................................5x30........................................1
32........OVS10-032.................. Main Shaft ............................................. ...............................................1
33........KEY5550...................... Key........................................................5x5x50....................................1
34........OVS10-034.................. Set Screw..............................................M3x12.....................................2
35........OVS10-035.................. Spur Gear.............................................. ...............................................1
36........OVS10-036.................. Brass Bushing ....................................... ...............................................2
37........TS-0208061 ................. Socket Head Cap Screw........................5/16”-18x1”............................16
38........OVS10-038.................. Transmission Rod Shaft......................... ...............................................2
39........OVS10-039.................. Transmission Rod.................................. ...............................................2
40........TS-0640091 ................. Hex Nut, Nylon Lock..............................3/8”-16 ....................................4
47........OVS10-047.................. Switch Cord........................................... ...............................................1
52........OVS10-052.................. Locking Nut ...........................................5/8”-11 ....................................1
55........OVS10-055.................. Rear Trunnion Bracket........................... ...............................................2
56........TS-0208082 ................. Socket Head Cap Screw........................5/16”-24x1-1/2”......................10
64........OVS10-064.................. Oil Lid.................................................... ...............................................1
66........OVS10-066.................. Hex Socket Cap Screw..........................3/8”-16x3/4”.............................4
67........TS-0680042 ................. Flat Washer...........................................3/8” .........................................8
86........OVS10-086.................. Angle Pointer......................................... ...............................................1
87........OVS10-087.................. Pan Head Machine Screw......................10-24x1/4”...............................1
88........OVS10-088.................. Cap ....................................................... ...............................................1
89........OVS10-089.................. Nut ........................................................15/16”-24 R.H .........................2
134......JOVS10-134 ................ Oil Plug..................................................PT1/4”.....................................1
135......JOVS10-135 ................ Brass Bushing Bracket........................... ...............................................1
136......JOVS10-136 ................ Shaft Brass Bushing .............................. ...............................................4
137......JOVS10-137 ................ Knob......................................................5/16”-18x3/4”...........................1
139......JOVS10-139W ............. Bracket Base......................................... ...............................................2
140......TS-0680032 ................. Flat Washer...........................................5/16” .....................................24
141......TS-0051021 ................. Cap Screw.............................................5/16”-18x5/8”...........................6
142......JOVS10-142 ................ Switch Box............................................. ...............................................1
143......JOVS10-143 ................ Pan Head Machine Screw......................3/16”-24x1-1/2”........................2
143A....JOVS10-143A.............. Hex Nut .................................................3/16”-24 ..................................2
144......JOVS10-144W ............. Vent Cover ............................................ ...............................................1
145......JOVS10-145W ............. Base...................................................... ...............................................1
146......JOVS10-146 ................ Motor Bracket ........................................ ...............................................1
147......JOVS10-147 ................ Motor..................................................... ...............................................1
............JOVS10-147MF ........... Motor Fan (not shown)........................... ...............................................1
............JOVS10-147MFC......... Motor Fan Cover (not shown)................. ...............................................1
............JOVS10-147CC ........... Capacitor Cover (not shown).................. ...............................................1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
............JOVS10-147RC ........... Running Capacitor (not shown)..............45uf, 250V ..............................1
............JOVS10-147SC............ Starting Capacitor (not shown)...............300MFD, 125VAC...................1
148......JOVS10-148 ................ Strain Relief Bushing ............................. ...............................................1
149......TS-0720081 ................. Lock Washer..........................................5/16” .....................................20
151......JOVS10-151 ................ Coupling Head....................................... ...............................................1
152......JOVS10-152 ................ Tank...................................................... ...............................................1
153......TS-0267041 ................. Set Screw..............................................1/4”-20x3/8”.............................2
154......JOVS10-154 ................ Tank Lid ................................................ ...............................................1
155......JOVS10-155 ................ Switch Push Button................................ ...............................................1
156......JOVS10-156W ............. Sanding Assembly Rack........................ ...............................................2
158......JOVS10-158W ............. Rear Trunnion........................................ ...............................................2
159......JOVS10-159 ................ Locking Knob.........................................3/8”-16x3/4”.............................2
160......JOVS10-160W ............. Dust Cover ............................................ ...............................................1
161......TS-0051061 ................. Hex Bolt.................................................5/16”-18x1-1/4”........................2
162......TS-0561021 ................. Hex Nut .................................................5/16”-18 ..................................6
163......JOVS10-163W ............. Working Table ....................................... ...............................................1
164......JOVS10-164 ................ Scale..................................................... ...............................................1
169......JOVS10-169 ................ Fixed Rod.............................................. ...............................................1
170......TS-0561031 ................. Hex Nut .................................................3/8”-16 ....................................2
171......JOVS10-171 ................ Rubber Feet .......................................... ...............................................4
172......JOVS10-172 ................ Sinking Head Screw...............................5/16”-18x3/4”...........................4
174......JOVS10-174 ................ JET Logo............................................... ...............................................1
177......JOVS10-177 ................ Pan Head Screw....................................3/16”-24x3/8”...........................2
178......JOVS10-178 ................ Switch.................................................... ...............................................1
179......JOVS10-179 ................ Spring Pin..............................................3x22........................................1
180......JOVS10-180 ................ Fiber Washer.........................................3/8” .........................................2
181......TS-0720091 ................. Lock Washer..........................................3/8” .........................................4
182......TS-0271071 ................. Set Screw..............................................3/8”-16x3/4”.............................1
183......JOVS10-183 ................ Warning Label ....................................... ...............................................1
184......JOVS10-184 ................ I.D Label................................................ ...............................................1
185......JOVS10-185 ................ Motor Label ........................................... ...............................................1
186......JOVS10-186 ................ Rivet...................................................... ...............................................4
187......TS-0267041 ................. Set Screw..............................................1/4”-20x3/8”.............................1
188......JOVS10-188 ................ Star Washer ..........................................3/16” .......................................2
189......TS-0680011 ................. Flat Washer...........................................3/16” .......................................1
190......TS-0267021 ................. Set Screw..............................................1/4”-20x1/4”.............................4
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Sanding Assemblies
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Sanding Assemblies
Index Part
No. No.
Description
Size
Qty.
93........OVS10-093.................. Wrench.................................................. ...............................................2
94........OVS10-094A................ Arbor .....................................................3/4” .........................................6
95........OVS10-095.................. Hex Nut ................................................. ...............................................6
96........OVS10-096.................. Spring Pin..............................................3.5x25.....................................3
97........30105000J ................... P.V.C.....................................................4” ............................................1
98........OVS10-098.................. Washer..................................................4” ............................................2
99........OVS10-099.................. Nut ........................................................3/4”-16”...................................6
100......575834......................... Sanding Sleeve (60 Grit)........................4” ..............................................
............575835......................... Sanding Sleeve (80 Grit)........................4” ..............................................
............575836......................... Sanding Sleeve (100 Grit)......................4” ..............................................
101......30105000I.................... P.V.C.....................................................3” ............................................1
102......575830......................... Sanding Sleeve (60 Grit)........................3” ..............................................
............575831......................... Sanding Sleeve (80 Grit)........................3” ..............................................
............575832......................... Sanding Sleeve (100 Grit)......................3” ..............................................
103......OVS10-103.................. Washer..................................................3” ............................................2
104......30105000H .................. P.V.C.....................................................2” ............................................1
105......575826......................... Sanding Sleeve (60 Grit)........................2” ..............................................
............575827......................... Sanding Sleeve (80 Grit)........................2” ..............................................
............575828......................... Sanding Sleeve (100 Grit)......................2” ..............................................
106......OVS10-106.................. Washer..................................................2” ............................................2
107......30105000G .................. P.V.C.....................................................1-1/2” ......................................1
108......575822......................... Sanding Sleeve (60 Grit)........................1-1/2” ........................................
............575823......................... Sanding Sleeve (80 Grit)........................1-1/2” ........................................
............575824......................... Sanding Sleeve (100 Grit)......................1-1/2” ........................................
109......OVS10-109.................. Washer..................................................1-1/2” ......................................2
110......30105000F................... P.V.C.....................................................1” ............................................1
111......575818......................... Sanding Sleeve (60 Grit)........................1” ..............................................
............575819......................... Sanding Sleeve (80 Grit)........................1” ..............................................
............575820......................... Sanding Sleeve (100 Grit)......................1” ..............................................
112......OVS10-112.................. Washer..................................................1” ............................................2
113......575814......................... Sanding Sleeve (60 Grit)........................3/4” ...........................................
............575815......................... Sanding Sleeve (80 Grit)........................3/4” ...........................................
............575816......................... Sanding Sleeve (100 Grit)......................3/4” ...........................................
114......OVS10-114A................ Arbor .....................................................5/8” .........................................1
115......OVS10-115.................. Hex Nut .................................................5/8” .........................................1
118......575810......................... Sanding Sleeve (60 Grit)........................5/8” ...........................................
............575811......................... Sanding Sleeve (80 Grit)........................5/8” ...........................................
............575812......................... Sanding Sleeve (100 Grit)......................5/8” ...........................................
............575813......................... Sanding Sleeve (120 Grit)......................5/8” ...........................................
119......OVS10-119A................ Arbor .....................................................1/2” .........................................1
120......OVS10-120.................. Hex Nut .................................................1/2” .........................................1
122......575806......................... Sanding Sleeve (60 Grit)........................1/2” ...........................................
............575807......................... Sanding Sleeve (80 Grit)........................1/2” ...........................................
............575808......................... Sanding Sleeve (100 Grit)......................1/2” ...........................................
............575809......................... Sanding Sleeve (120 Grit)......................1/2” ...........................................
124......OVS10-124A................ Arbor .....................................................3/8” .........................................1
125......OVS10-125.................. Hex Nut .................................................3/8” .........................................1
127......575802......................... Sanding Sleeve (60 Grit)........................3/8” ...........................................
............575803......................... Sanding Sleeve (80 Grit)........................3/8” ...........................................
............575804......................... Sanding Sleeve (100 Grit)......................3/8” ...........................................
128......OVS10-117.................. Set Screw..............................................3/16”-24x1/4”...........................4
129......OVS10-129.................. Arbor ..................................................... ...............................................1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
130......575800......................... Sanding Sleeve (100 Grit)......................1/4” ...........................................
............575801......................... Sanding Sleeve (120 Grit)......................1/4” ...........................................
133......OVS10-133A................ Spindle.................................................. ...............................................1
165......JOVS10-165 ................ Table Insert (medium)............................ ...............................................1
166......JOVS10-166 ................ Table Insert (small)................................ ...............................................1
167......JOVS10-167 ................ Table Insert (Large) ............................... ...............................................1
191......JOVS10-191 ................ Spring Pin..............................................5x25........................................6
192......JOVS10-192 ................ Spring Pin..............................................3x25........................................1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|