OWNER'S MANUAL
DC-1200C Dust Collector
JET EQUIPMENT & TOOLS, INC.
A WMH Company
P.O. BOX 1349
Auburn, WA 98071-1349
e-mail [email protected]
Phone:253-351-6000
Fax: 1-800-274-6840
M-708634C 1/02
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
1.
2.
Read and understand the entire contents of this manual before attempting assembly or
operation. Do not use this machine until proper training and knowledge has been obtained.
Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before
servicing.
3.
4.
5.
6.
Do not use outdoors or on wet surfaces.
Do not allow to be used as a toy. Close attention is necessary when used near children.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If Dust Collector is not working as it should, has been
dropped, damaged, left outdoor, or dropped in water, return it to a service center.
7.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run Dust Collector over cord. Keep cord away from heated surfaces.
8.
9.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or Dust Collector with wet hands.
10. Do not put any objects into the openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all parts of body away from opening and moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
13. Do not use without dust bag and/or filters in place.
14. Turn off all controls before unplugging.
15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they
may be present.
16. Do not operate without hose connected to the inlet ports or covered by an inlet cap. Hazardous
moving parts inside. Unplug machine before removing inlet port, inlet cap, hose, or inlet guard.
17. Use the inlet caps to cover the inlet port openings that are not connected to hoses.
18. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
Crystalline silica from bricks and cement and other masonry products, and
Arsenic and chromium from chemically-treated lumber.
19. Your risk from those exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specifically designed to filter out microscopic
particles
20. Do not operate tool while under the influence of drugs, alcohol or any medication.
21. Make sure the extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. An undersize cord will cause a drop
in the line voltage resulting in loss of power and overheating. The table below shows the correct
size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller gauge number, the heavier the cord.
22. Do not use dust collector for anything except wood dust. Materials such as liquids, metal shavings,
metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into
contact with any part of the dust collector.
23. Ground your dust collector along all plastic componets. The connection of bare 12 gauge copper
wire on all plastic hoses, fittings and blast gates to all machines will help reduce the occurrence of
static build up and discharge.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
DC-1200C
Stock Number..............................................................................................................................708634C
Blower Wheel Diameter........................................................................................................................12"
Sound Rating at 3 feet................................................................................................................. 80-85 db
Hose Diameter................................................................................................................................ 4" & 6”
Air Flow (CFM) ................................................................................................................................. 1,200
Velocity at 4” (FPM)........................................................................................................................ 13,745
Static Pressure (inch of water).......................................................................................................... 11.44
Bag Diameter .......................................................................................................................................20"
Bag Length...................................................................................................................................45 & 28”
Collector Bag Capacity (cu. ft.) .............................................................................................................5.6
Overall Dimensions 2 Micron...............................................................................37"L x 28"W x 70-7/8"H
Motor (TEFC) ...........................................................................................................2 HP, 1Ph 230V only
Net Weight (approx.) .....................................................................................................................125 lbs.
Table of Contents
Page
Warranty .................................................................................................................................................2
Warnings.................................................................................................................................................3
Specifications..........................................................................................................................................4
Table of Contents....................................................................................................................................4
Unpacking DC-1900.................................................................................................................................5
Contents of Shipping Carton....................................................................................................................5
Tools Required for Assembly...................................................................................................................5
Assembly..............................................................................................................................................6-8
Electrical Connections .............................................................................................................................9
Turning the Machine On & Off .................................................................................................................9
Maintenance............................................................................................................................................9
Cleaning the Filter Bag......................................................................................................................9
Removing the Collector Bag..............................................................................................................9
Motor.................................................................................................................................................9
Connecting the Dust collector to a Machine .............................................................................................9
Grounding the Dust Collection System.....................................................................................................9
Parts Breakdown and Parts List ........................................................................................................10-12
Wiring Diagrams....................................................................................................................................12
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the dust collector!
Failure to comply may cause serious injury!
Unpacking
1. Remove all contents from the shipping
carton.
2. Report any damage to your distributor.
3. Do not discard any shipping material until
after the dust collector has been assembled
and is running properly.
Contents of the Shipping Cartons
Canister Filter Box
1. Canister Filter
1. Handle
1. Bag of Hardware for Handles
2. M10 Hex Nuts
2. M10 Flat Washers
1. M10 Lock Washer
4. Knobs
DC-1200C
1. Base
1. Owner's Manual
1. Warranty Card
1. Motor/Fan Assembly
5. Collector Bags
1. Snap Rings
2. Ring Clamps
4. Casters
1. Inlet Port & Inlet Caps
3. Support Legs
1. Housing
1. Bag of Assembly Hardware
16. M8 x 16 Hex Cap Bolts
34. M8 Flat Washers
8. M6 x 12 Pan Head Flange Bolts
10. M8 Hex Nuts
Tools Required for Assembly
2. 13mm Wrenches or Sockets
1. 14mm Wrench or Socket
1. #2 Cross Point Screw Driver
1. 17mm Wrench
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
1. Install four casters to the under side of the
base as pictured in Fig. 1. Thread the hex
nut (B, Fig. 1) onto the caster shaft. Then
slide the lock washer (A, Fig. 1) over the
caster shaft. Thread the caster shaft into
the threaded hole on the underside of the
base, turn until snug. Tighten the nut (B,
Fig. 1) against the base with a 14mm
wrench. This will give the caster proper
clearance.
2. Place the base with casters on the ground.
Attach the motor and fan assembly (A, Fig.
2) to the base using four M8 x 16 hex cap
bolts, four M8 flat washers (B, Fig. 2), and a
13mm wrench.
WARNING
The dust collector must be disconnected
from the power source during assembly.
Failure to comply may result in serious
injury!
3. Attach inlet guard (A, Fig. 3) to fan housing
using eight M5 x 12 pan head screws (B,
Fig. 3). Press the inlet port onto the inlet
guard until it snaps into place.
WARNING
To reduce the risk of injury from moving
parts, always keep inlet ports covered with
the caps provided, if they are not
connected to a flexible hose. Failure to
comply may result in serious injury!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach three support brackets (A, Fig. 4) to
the base using six M8 x 16 hex cap bolts
and six M8 flat washers (B, Fig. 4). Hand
tighten only at this time.
5. Install the housing (A, Fig. 5) to two support
brackets using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts
(B, Fig.5). Be sure hose opening faces fan
housing. Before attaching third support
bracket place the hanger bracket (C, Fig.5)
between the support bracket and the
housing. Tighten all nuts and bolts at this
time with a 13mm wrench.
6. Attach the hose (A, Fig. 6) between the fan
housing and the collector housing with two
clamps (B, Fig. 6). Tighten the clamps to
secure the hose.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Place the ring over the top of the plastic bag
and fold over the bag approximately three
inches, Figure 7.
8. Insert the snap ring (A, Fig. 8) of the
collector bag into the bottom of the housing
at an angle.
9. Pull down on the ring to make sure it “seats”
in the housing.
Note: make sure the snap ring “snaps” into
place in the housing, and also that the
plastic bag hangs down approximately 3” so
that there are no air leaks.
10. Mount the handle onto the canister filter with
two M10 hex nuts, two M10 flat washers,
and a M10 lock washer, see Figure 9.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
Removing the Collector Bag
WARNING
CAUTION
All electrical connections must be done by a
qualified electrician. All adjustments or
repairs must be done with the dust collector
disconnected from the power source,
unplugged. Failure to comply may result in
serious injury!
Wearing a particle mask/respirator for
protection against fine dust particles during
cleaning is highly recommended.
1. Disconnect the machine from the power
source, unplug.
The DC-1200C dust collector is rated at 230V
Only and is not supplied with a plug. Use a
plug and outlet rated at least 20 amps. The
circuit for the machine should also be protected
by at least a 20 amp circuit breaker or fuse.
Keep in mind that a curcuit being used by other
machines, tools, lights, heaters, etc. at the same
time will add to the electrical load. A dedicated
curcuit to the dust collector will give you the
best results since dust collectors are generally
used at the same time other tools are running.
2. Remove the collector bag by pushing the
ring of the collector bag upwards at an angle
and pulling the bag and snap ring out.
3. Empty the contents into an appropriate
container.
4. See Page 8 for details on replacing the
collector bags.
Motor
Before hooking up to the power source, make
sure that the switch is in the off position.
Make frequent inspections of the motor fan and
blow out (with low pressure air hose) or vacuum
any accumulation of foreign material in order to
maintain normal motor ventilation.
Turning the Machine On & Off
Before hooking up to the power source, make
sure that the switch is in the off position.
Connecting the Dust collector to a
Machine
The dust collector can be turned on by pressing
the start button mounted next to the motor.
Press the stop button to turn off the dust
collector.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer
vent hose is not acceptable for this purpose.
Contact your nearest JET distributor for the full
line of JET Dust Collector Hoses and
Accessories. Customize your installation and
obtain maximum performance with JET's dust
hoods, hoses, clamps, fittings, and blast gates.
Maintenance
WARNING
Never perform maintenace on this machine
before turning switch off and removing plug
from power source, unplug.
You can also purchase the JET “Dust Collection
Basics Video” stock # JW1050V through your
JET Distributor
Failure to comply may cause serious injury!
Grounding the Dust Collection System
Cleaning the Filter
The dust collection system includes the dust
collector and the hose, or duct work you use to
connect the tools. The dust collector is grounded
though the ground wire in the cord. The hose or
duct work you use to connect the tool to the dust
collector must also be grounded. To assist in
grounding your system you can purchase the JET
“Dust Collector Grounding Kit” stock # JW1053,
and also the JET “Dust Collection Basics Video”
stock # JW1050V through JET Distributors.
Clean both the filter and collector bag frequently
to keep the collector's performance at its
optimum.
To clean the filter turn the handle a couple
rotations so the dust falls into the collector bag.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown for DC-1200C Dust Collector w/Canister Filter
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for the DC-1200C Dust Collector w/Canister Filter
Index Part
No. No.
Description
Size
Qty.
1..........708739......................... Filter...................................................... ...............................................1
2..........331010......................... Shaft...................................................... ...............................................1
3..........331012......................... Scraper.................................................. ...............................................2
4..........331015......................... Plate...................................................... ...............................................2
5..........331009......................... Support.................................................. ...............................................2
6..........ST049200 .................... Tapping Screw.......................................M4x8.......................................4
7..........331050......................... Handle................................................... ...............................................1
8..........NH101700.................... Nut ........................................................M10.........................................2
9..........WF102025 ................... Flat Washer...........................................M10.........................................2
10........WS100000................... Spring Washer.......................................M10.........................................1
11........331014......................... Bracket.................................................. ...............................................1
12........150623......................... Pad........................................................ ...............................................1
13........BR000052.................... Rivet...................................................... ...............................................3
14........SH060400.................... Hex Head Bolt .......................................M6x20.....................................4
15........WS060000................... Spring Washer.......................................M6 ..........................................4
16........WF061310 ................... Flat Washer...........................................M6 ..........................................4
17........NH061000.................... Nut ........................................................M6 ..........................................8
18........331017......................... Plate...................................................... ...............................................2
19........SH069300.................... Hex Head Bolt .......................................M6x12.....................................4
20........331037......................... Knob......................................................M6x20.....................................4
21........331031......................... Pad........................................................ ...............................................1
22........331051......................... Soft Grip Handle.................................... ...............................................2
26........331038......................... Snap Ring.............................................. ...............................................1
27........998674-36.................... PVC Bag ............................................... ...............................................5
28........411035W ..................... Impeller Housing.................................... ...............................................1
29........411026W ..................... Motor Bracket........................................ ...............................................1
30........998621......................... Strain Relief........................................... ...............................................1
31........MA411003.................... Motor.....................................................2 HP, 1Ph ...............................1
............DC1100-50W ............... Motor Fan Cover (not shown) ................ ...............................................1
............MF411012.................... Motor Fan (not shown)........................... ...............................................1
............CA003030.................... Running Capacitor (not shown)..............30MFD, 300V..........................1
............CA020010.................... Starting Capacitor (not shown)...............200MFD, 125V........................1
32........411051......................... Switch Box ............................................ ...............................................1
33........411053......................... Switch Plate........................................... ...............................................1
34........994542......................... Switch....................................................1 Ph........................................1
35........IC420002 ..................... Power Cord............................................ ...............................................1
36........420051......................... Motor Packing ....................................... ...............................................1
37........AB411059 .................... Impeller .................................................12” ..........................................1
38........411036W ..................... Inlet Guard ............................................ ...............................................1
39........427028......................... Inlet Port................................................2 @ 4”.....................................1
40........420203......................... Inlet Cap................................................ ...............................................2
41........430034......................... Inlet Flange Packing.............................. ...............................................1
42........411041W ..................... Base...................................................... ...............................................1
43........402036......................... Pivoting Caster...................................... ...............................................4
44........420012W ..................... Housing................................................. ...............................................1
45........402004W ..................... Support.................................................. ...............................................3
46........411009......................... Hose...................................................... ...............................................1
47........420010......................... Ring Clamp ...........................................5” ............................................2
48........450038......................... Bracket Cap........................................... ...............................................1
49........ST039304 .................... Tapping Screw.......................................M3.5x12..................................6
50........KS050525 .................... Key........................................................5x5x25....................................1
51........TS-1540061 ................. Nut ........................................................M8 ........................................10
52........TS-0561031 ................. Nut ........................................................3/8”-16UNC.............................4
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
53........TS-1490031................. Hex Head Bolt .......................................M8x20.....................................1
54........TS-1490011 ................. Hex Head Bolt .......................................M8x12.....................................4
55........TS-1490021 ................. Hex Head Bolt .......................................M8x16...................................16
56........TS-1490041 ................. Hex Head Bolt .......................................M8x25.....................................4
57........TS-1554041 ................. Pan Head Bolt W/Flange .......................M6x12.....................................2
58........TS-0680031 ................. Flat Washer...........................................M8 ..........................................1
59........TS-1554041 ................. Pan Head Bolt W/Flange .......................M6x12.....................................8
60........TS-0680031 ................. Flat Washer...........................................M8 ........................................34
61........TS-0720081 ................. Spring Washer.......................................M8 ..........................................8
62........TS-1551071 ................. Spring Washer.......................................M10.........................................4
63........ST059304 .................... Tapping Screw.......................................M5x12.....................................2
............DC1200-53................... Grounding Label (not shown)................. ...............................................1
............DC1200-54................... Direction Label (not shown) ................... ...............................................1
............DC1200A-NP ............... Name Plate (not shown) ........................ ...............................................1
............DC1100-HP.................. Hardware Package (not shown) ............. ...............................................1
............DC1200A-CS ............... Centrifugal Switch (not shown)............... ...............................................1
............DC1900-53................... Warning Label (not shown) .................... ...............................................1
Wiring Diagram For Single Phase 230V Only Dust Collector
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|