This Manual is Bookmarked
Operating Instructions and Parts Manual
17” Drill Press
Model JDP-17MF
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123
Ph.: 800-274-6848
Part No. M-354169
Revision C1 01/06
Copyright © WMH Tool Group
Download from Www.Somanuals.com. All Manuals Search And Download.
, WARNING
Wear eye protection.
Always keep guards in place and in proper operating condition. Do not operate the machine
without the guards for any reason.
Support workpiece adequately at all times during operation; maintain control of work at all times.
This drill press is designed and intended for use by properly trained and experienced personnel
only. If you are not familiar with the proper and safe operation of a drill press, do not use until
proper training and knowledge has been obtained.
•
REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and
adjusting wrenches are removed from the machine before turning it on.
•
•
KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.
•
•
•
KEEP CHILDREN AWAY. All visitors should be kept a safe distance from the work area.
MAKE THE WORKSHOP KIDPROOF with padlocks, master swatches, or by removing starter keys.
DON’T FORCE THE MACHINE. It will do the job better and safer at the rate for which it was
designed.
•
•
USE THE RIGHT TOOL. Don’t force a machine or attachment to do a job for which it was not
designed.
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your machine will
draw. An undersized cord will cause a drop in the line voltage resulting in power loss and
overheating. The table following shows the correct size to use depending on the cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge
number, the heavier the cord.
Total Length of Cord in Feet
0-25
16
25-50
14
AWG
•
•
WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
ALWAYS USE SAFETY GLASSES. Also use face or dust masks if the cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.
•
•
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
•
•
ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position
before plugging in.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not
recommended by JET may cause hazards or risk of injury to persons.
•
•
NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped.
CHECK DAMAGED PARTS. Before further use of the machine, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function - check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
•
•
NEVER LEAVE THE MACHINE RUNNING UNATTENDED. TURN POWER OFF. Don’t leave the
machine until it comes to a complete stop.
SOME DUST CREATED by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
•
•
•
Lead from lead based paint
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
•
Your risk from those exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specifically designed to filter out microscopic particles
•
•
•
•
DO NOT operate tool while under the influence of drugs, alcohol or any medication.
DO NOT drill pieces of material that are too small to be safely supported.
WHEN drilling a large workpiece, provide additional support at table height.
ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident
Prevention Manual for Industrial Operations and also in the safety Data Sheets provided by the NSC.
Please also refer to the American National Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.
•
SAVE THESE INSTRUCTIONS refer to them often and use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Instructions
Caution: This tool must be grounded while in use to protect the operator from electric shock.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
As received from the factory, your drill press is ready to run at 115 volt operation. This drill press, when
wired for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one
illustrated in (A). A temporary adapter, which looks like the adapter as illustrated in (B), may be used to
connect this plug to a two-pole receptacle, as shown in (B) if a properly grounded outlet is not available.
The temporary adapter should only be used until a properly grounded outlet can be installed by a
qualified electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab,
extending from the adapter, must be connected to a permanent ground such as a properly grounded
outlet box, as shown in (B).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
230 Volt Operation
If 230V, single phase operation is desired, the following instructions must be followed:
1. Disconnect the machine from the power source.
2. This JET drill press is supplied with four motor leads that are connected for 115V operation, as
shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B.
3. The 115V attachment plug (A), supplied with the drill press, must be replaced with a UL/CSA listed
plug suitable for 230V operation (D). Contact your local Authorized JET Service Center or qualified
electrician for proper procedures to install the plug. The drill press must comply with all local and
national codes after the 230 volt plug is installed.
4. The drill press with a 230 volt plug should only be connected to an outlet having the same
configuration (D). No adapter is available or should be used with the 230 volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded.
If you are not sure, have a registered electrician check the receptacle.
NOTE: If 230V is needed, a 230V light bulb must be used in the lamp. Or, the lamp circuit may be
re-wired in accordance with the diagram on page 21 and a 115V bulb may continue to be used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Off Switch Padlock
Model No. BP-1, Stock No. 709736
To safeguard your machine from unauthorized operation and to avoid accidental starting by young
children, the use of a padlock is highly recommended. JET model BP-1 is available from your local
authorized JET distributor or by calling WMH Tool Group at 800-274-6848.
To lock out an on-off switch:
1. Open the padlock. See Fig. A.
2. Insert through holes in the start button. See Fig. B
3. Close the padlock.
4. Place the key in a safe place.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications:
JDP-17MF
Stock Number .....................................................................................................................................354169
Swing....................................................................................................................................................16-1/2”
Type ........................................................................................................................................................Floor
Drilling Capacity ........................................................................................................................................5/8”
Chuck Size................................................................................................................................................5/8”
Spindle Travel ........................................................................................................................................4-3/8”
Spindle Distance to Base...........................................................................................................................49”
Spindle Distance to Table (max.).........................................................................................................29-1/8”
Table Size Diameter.............................................................................................................................13-3/4”
Table Tilt........................................................................................................................................... + or - 45°
Spindle Taper..........................................................................................................................................MT-2
Column Diameter ...................................................................................................................................3-1/8”
Number of Spindle Speeds......................................................................................................................... 16
Range of Spindle Speeds ......................................................................................................200-3,630 RPM
Overall Height ............................................................................................................................................66”
Base Size............................................................................................................................. 12-1/2” x 19-5/8”
Motor ............................................................................................................................................3/4HP, 1 Ph
............................................................................................................................... 115/230V, prewired 115V
Net Weight (approx.)............................................................................................................................ 189 lb.
Shipping Weight (approx.) ................................................................................................................... 200 lb.
Table of Contents
Page
Warranty........................................................................................................................................................ 2
Warnings....................................................................................................................................................3-4
Grounding Instructions.................................................................................................................................. 5
115V Operation............................................................................................................................................. 5
230V Operation............................................................................................................................................. 6
On-Off Switch Padlock.................................................................................................................................. 7
Specifications................................................................................................................................................ 8
Table of Contents.......................................................................................................................................... 8
Contents of Shipping Container.................................................................................................................... 9
Tools Supplied for Assembly ........................................................................................................................ 9
Tools Required for Assembly........................................................................................................................ 9
Before Assembly........................................................................................................................................... 9
Assembly................................................................................................................................................10-11
Removing the Chuck and Arbor.................................................................................................................. 11
Adjusting the Depth Stop ............................................................................................................................ 12
Changing Spindle Speeds .......................................................................................................................... 12
Speed and Pulley Chart.............................................................................................................................. 13
Return Spring Adjustment........................................................................................................................... 14
Table Tilt Adjustment .................................................................................................................................. 14
Basic Operation........................................................................................................................................... 15
Lubrication................................................................................................................................................... 15
Troubleshooting .......................................................................................................................................... 16
Part’s Breakdown........................................................................................................................................ 17
Part’s List ...............................................................................................................................................18-20
Wiring Diagram ........................................................................................................................................... 21
The specifications in this manual are given as general information and are not binding. WMH TOOL
GROUP reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Shipping Container
1. Head Assembly
1. Table
1. Column and Bracket Assembly
1. Base
1. Owner’s Manual
1. Warranty Registration Card
1. Chuck and Chuck Key
3. Downfeed Handle
1. Table Bracket Lock Handle
1. Table Bracket Raising Handle
4. M10 x 40 Hex Cap Bolts
1. Arbor
1. Drift Key
Tools Supplied for Assembly
1. 3mm Hex Wrench
1. 5mm Hex Wrench
Tools Required for Assembly
1. 17mm Box Wrench or a 6”-8” Adjustable
Wrench
, WARNING!
Read and understand all assembly
instructions before attempting assembly!
Failure to comply may cause serious injury!
Before Assembly
1. Remove the contents from the shipping
container.
2. Compare the contents of the shipping
container with the list found above. Report
any shortages or damage to your JET
distributor.
3. Clean all rust protected surfaces with
kerosene or a light solvent. Do not use
lacquer thinner, paint thinner, or gasoline.
These will damage plastic components and
painted surfaces.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
1. Place the base (A, Fig. 1) on a level floor.
2. With a 17mm wrench attach the column
assembly (B, Fig. 1) to the base (A, Fig. 1)
with four M10 x 40 hex cap bolts (C, Fig. 1).
Tighten firmly.
3. Thread lock handle (D, Fig. 2) into the table
bracket (E, Fig. 2).
4. Loosen the set screw (F, Fig. 3) on the
raising handle (G, Fig. 3) with a 3mm hex
wrench.
5. Slide the handle onto the table bracket
shaft.
6. Turn the handle until the set screw is
opposite the flat section on the shaft, and
tighten the set screw to secure the handle.
7. Insert the table (H, Fig. 3) into the table
bracket.
8. Tighten the table lock handle (I, Fig. 3).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
9. With the aid of a second person, carefully lift
the head onto the column top. Caution:
The head assembly is heavy! Use care
when lifting onto the column!
below the chuck.
3. Place a piece of scrap wood on the table,
and lower quill using the down feed handle.
4. Rotate spindle to align the key hole in the
spindle with the key hole in the quill.
10. Rotate head assembly until sides of the belt
cover are parallel with the sides of the base.
5. Insert the drift key (D, Fig. 6) into the aligned
slots and tap lightly. The chuck and arbor
assembly should fall from the spindle.
11. Tighten two set screws (A, Fig. 4) with a
5mm wrench until they are snug.
12. Install three down feed handles (B, Fig. 4)
into the down feed hub (C, Fig. 4).
13. Raise table to approximately seven inches
below spindle assembly, and lock the table
in place.
14. Place a piece of scrap wood on the table.
15. Thoroughly clean spindle, arbor, and chuck.
Important: These three pieces must be
free of any rust protection, or lubricant. If
they are not clean, the arbor and chuck will
fail to seat in the spindle.
16. Place arbor into the chuck.
17. Twist the chuck to retract the chuck jaws if
they are exposed.
18. Place arbor and chuck assembly into the
spindle.
19. Turn the arbor and chuck assembly until the
tang on the arbor engages the slot at the
end of the spindle.
20. Lower the down feed handle so that the
chuck meets the scrap wood. Pressure on
the down feed handle once the chuck meets
the scrap wood seats the arbor and chuck
into the spindle, See Figure. 5.
Removing the Chuck and Arbor
1. Unplug machine from the power source.
2. Raise the table until it is about seven inchs
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Depth Stop
To drill multiple holes at the same preset depth,
use the depth stop:
1. Use a pencil to mark the depth the bit will
drill into the workpiece (A, Fig. 7).
2. With the drill bit in the chuck, lower down
feed handle to advance bit to your mark,see
Figure 7.
3. With your other hand, advance the lock nuts
(B, Fig. 7) on the depth stop rod until they
are snug to the seat (C, Fig. 7).
4. The drill bit will now advance to this point.
5. To release, advance the nuts counter-
clockwise to the top of the depth stop.
Changing Spindle Speeds
A spindle speed and belt arrangement chart are
found on the inside of the belt cover (D, Fig. 8).
Refer to this chart whenever changing speeds.
To change spindle speeds:
1. Unplug the machine from the power
source.
2. Loosen two bar knobs (E, Fig. 8) found on
each side of the head assembly.
3. Rotate the tension adjuster (F, Fig. 8) to
bring the motor base as close to the head as
possible.
4. Change the belts location according the
speed chart and the speed you desire.
5. Rotate the tension adjuster (F. Fig. 8) to
tension the belts.
6. Tighten two bar knobs (E, Fig. 8). Belts are
properly tensioned when finger and thumb
pressure midway between the two pulleys
causes approximately ½” deflection.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Return Spring Adjustment
The return spring is adjusted at the factory and
should not need further adjustment.
adjustment is deemed necessary:
If
1. Unplug the machine from the power
source.
2. Loosen two jam nuts (A, Fig. 9). Do not
remove.
3. Firmly hold the coil spring cover (B, Fig. 9).
4. Pull out the cover and rotate until the pin (C,
Fig. 9) on the return spring plate engages
the next notch in the coil spring cover. Turn
the cover clockwise to decrease tension and
counter-clockwise to increase tension.
5. Tighten two jam nuts (A, Fig. 9). Do not
over-tighten. Nuts should not contact the
housing when tight. The jam nuts should be
tightened against eachother.
Work Light
Install a light bulb, no larger than 60 watts into
the socket accessed from beneath the head.
The light bulb is controlled by the rocker switch
(D, Fig. 9).
Table Tilt Adjustment
CAUTION!
Remove the alignment pin first and then
loosen the hex cap bolt. Failure to comply
may cause the table assembly to separate
from the column and fall.
To tilt the table:
1. Turn nut (E, Fig. 10) clockwise to pull out
the alignment pin (F, Fig. 10).
2. Loosen hex cap bolt (G, Fig. 10), and tilt the
table to the desired angle.
3. Tighten the hex cap bolt (G, Fig. 10).
4. The alignment pin only works at 90° and
must be reinserted when the table is
returned to 90°.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
•
Always use a back-up piece of scrap wood
to cover the table. This protects both the
table and the drill bit.
•
Place material to be drilled in such as way
as to come into contact with the left side of
the column. This prevents the material from
spinning.
, WARNING!
If the work piece is not large enough to come
into contact with the column, use a
clamp or drill press vise that is securely
fastened to the table!
Failure to comply may cause serious injury!
•
Feed the bit into the material with only
enough force to allow the drill bit to work.
Feeding too slowly may cause burning of
the workpiece. Feeding too quickly may
cause the motor to stop and/or the drill bit to
break.
•
•
Generally speaking, the smaller the drill bit,
the greater the RPM required.
Wood
requires higher speeds than metal. Metal is
usually drilled at slower speeds.
In dusty environments, frequently blow out
any dust that accumulates inside the motor.
Lubrication
Periodically lubricate the gear and the rack, the
table elevation mechanism, the splines
(grooves) in the spindle, and the teeth of the
quill with a #2 tube grease.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Probable Cause
Trouble
Remedy
1. Drill press unplugged from
wall, or motor.
2. Fuse blown, or circuit breaker
tripped.
3. Cord damaged.
4. Starting capacitor bad.
1. Check all plug connections.
2. Replace fuse, or reset circuit
breaker.
3. Replace cord.
4. Replace starting capacitor.
Drill press will not start.
1. Extension cord too light or too
long.
2. Low current.
1. Replace with adequate size
and length cord.
2. Contact a qualified electrician.
Drill press does not come
up to speed.
1. Adjust stand so that it rests
evenly on the floor.
2. Replace belts.
1. Stand on uneven surface.
2. Bad belt(s).
Drill Press vibrates
excessively.
1. Incorrect belt tension.
1. Adjust belt tension. See
“Changing Spindle Speeds”,
page 12.
2. Lubricate spindle. See
“Lubrication” page 15.
2. Dry spindle.
Noisy Operation.
3. Check tightness of retaining
nut on pulley, and tighten if
necessary.
3. Loose spindle pulley.
4. Tighten set screws in pulleys.
4. Loose motor pulley.
1. Incorrect Speed.
1. Change to appropriate speed,
see speed and pulley chart,
page 13.
2. Chips not clearing from hole or
bit.
3. Dull drill bit.
4. Feeding too slow.
1. Bit sharpened incorrectly.
2. Bent drill bit.
3. Bit, or chuck not installed
properly.
2. Retract drill bit frequently to
remove chips.
3. Resharpen, or replace drill bit.
4. Increase feed rate.
Workpiece Burns.
Drill bit wanders.
1. Resharpen bit correctly.
2. Replace drill bit.
3. Reinstall the chuck, or bit
properly.
1. Place a scrap board
underneath the workpiece to
prevent splintering.
1. No backing board used.
Wood splinters on the
underside.
1. Workpiece pinching the bit.
2. Excessive feed rate.
3. Chuck jaws not tight.
4. Improper belt tension.
1. Support or clamp workpiece.
2. Decrease feed rate.
3. Tighten chuck jaws.
4. Increase belt tension, see
page 12.
Drill bit binds in workpiece.
1. Bent drill bit.
1. Replace drill bit.
Excessive drill bit runout,
or wobble.
2. Worn spindle bearings.
3. Bit, or chuck not properly
installed.
2. Replace spindle bearings.
3. Reinstall the bit, or chuck
properly.
1. Spring has improper tension.
Quill returns too slow, or
too fast.
1. Adjust “Return Spring
Tension,” page 14.
1. Clean all mating surfaces
thoroughly with a cleaner
degreaser.
Chuck, or arbor do not stay 1. Dirt, grease, etc on arbor,
chuck, or spindle.
in place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Breakdown for JDP-17MF
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for JET JDP-17MF Drill Press
Description
Index Part
No. No.
Size
Qty.
1 ..........10600111 ......................Base..................................................................... .................................... 1
2A........12909001A1..................Column and Holder Assy..................................... .................................... 1
3 ..........TS-1525021 ..................Set Screw.............................................................M10x12....................... 1
5 ..........TS-1491061 ..................Hex Cap Bolt........................................................M10x40....................... 4
6 ..........10700605A1..................Bracket................................................................. .................................... 1
7 ..........10600702 ......................Pinion Gear.......................................................... .................................... 1
8 ..........10600802 ......................Gear Shaft............................................................ .................................... 1
9 ..........10600902 ......................Worm Pinion ........................................................ .................................... 1
10 ........10601002 ......................Crank Handle....................................................... .................................... 1
11 ........TS-1523031 ..................Set Screw.............................................................M6x10......................... 1
12 ........10901203A1..................Table Bracket Assy.............................................. .................................... 1
13 ........TS-0071011 ..................Hex Cap Bolt........................................................5/8”x1-1/2” .................. 1
14 ........10901402 ......................Locator Pin........................................................... .................................... 1
15 ........TS-0561011 ..................Hex Nut ................................................................1/4".............................. 1
16 ........10601601 ......................Angle Scale.......................................................... .................................... 1
17 ........10801701 ......................Centering Scale ................................................... .................................... 1
18 ........2658MZDU36................Drive Screw.......................................................... .................................... 4
19 ........10601901 ......................Column Lock Handle............................................ .................................... 1
20 ........10602001 ......................Table Lock Handle............................................... .................................... 1
21 ........10702112 ......................Table .................................................................... .................................... 1
22 ........10602205 ......................Rack..................................................................... .................................... 1
23 ........10702307A1..................Rack Ring ............................................................ .................................... 1
24 ........TS-1523031 ..................Set Screw.............................................................M6x10......................... 1
25 ........10902515A1..................Head..................................................................... .................................... 1
26 ........TS-1525021 ..................Set Screw.............................................................M10x12....................... 2
27 ........10602702 ......................Lamp Socket........................................................ .................................... 1
28 ........TS-1534042 ..................Pan Head Screw..................................................M6x12......................... 2
29 ........10902091 ......................Handle Shifter ...................................................... .................................... 1
30 ........10603002A1..................Cam...................................................................... .................................... 1
31 ........TS-1490021 ..................Hex Cap Bolt........................................................M8x16......................... 1
32 ........10703211 ......................Slide Bar (right).................................................... .................................... 1
33 ........10903302 ......................Slide Bar Bolt ....................................................... .................................... 2
34 ........10703414 ......................Motor Base...........................................................75x125........................ 1
35 ........TS-0720111 ..................Lock Washer........................................................½”................................ 2
36 ........TS-1540071 ..................Hex Nut ................................................................M12............................. 2
37 ........ ......................................Handle Body (re:17373839)................................. .................................... 1
38 ........17373839 ......................Feed Shaft Assy (#37,38,39)............................... .................................... 1
39 ........ ......................................Spring Pin (re: 17373839).................................... .................................... 1
43A......10604303A1..................Handle Bar Assy .................................................. .................................... 3
45 ........10604505 ......................Scale Ring............................................................ .................................... 1
46 ........10904616 ......................Scale .................................................................... .................................... 1
48 ........2658MZDU36................Drive Screw.......................................................... .................................... 2
49A......10604902A2..................Coil Spring and Cover.......................................... .................................... 1
51 ........10905116 ......................Spring Seat .......................................................... .................................... 1
52 ........10905203 ......................Plate..................................................................... .................................... 1
53 ........TS-0561052 ..................Hex Nut ................................................................1/2"-20UNF................. 1
54 ........10605403 ......................Quill Set Screw .................................................... .................................... 1
55 ........TS-1540071 ..................Hex Nut ................................................................M10............................. 1
56 ........10905612 ......................Quill...................................................................... .................................... 1
57 ........10705703 ......................Rubber Washer.................................................... .................................... 1
58 ........10905829 ......................Spindle ................................................................. .................................... 1
59 ........BB-6205ZZ....................Ball Bearing.......................................................... .................................... 1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
61 ........BB-6203Z......................Ball Bearing.......................................................... .................................... 1
62 ........10606201 ......................Washer................................................................. .................................... 1
63 ........10606301 ......................Lock Nut............................................................... .................................... 1
64 ........10606401 ......................Spindle Nut .......................................................... .................................... 1
65 ........10706508A1..................Driving Sleeve...................................................... .................................... 1
66 ........BB-6205Z......................Ball Bearing.......................................................... .................................... 2
67 ........10706705 ......................Collar.................................................................... .................................... 1
68 ........10706802 ......................Retaining Ring ..................................................... .................................... 2
69 ........10606904 ......................Pulley Set Nut ...................................................... .................................... 1
70 ........10607018 ......................Spindle Pulley ...................................................... .................................... 1
71 ........561766 ..........................Arbor ....................................................................MT2xJT3..................... 1
72A......561708 ..........................Chuck................................................................... .................................... 1
73 ........10607303 ......................Wedge.................................................................. .................................... 1
74 ........8907522151 ..................Motor.................................................................... .................................... 1
............82061041 ......................Motor Fan (not shown)......................................... .................................... 1
............89075161 ......................Motor Fan Cover (not shown).............................. .................................... 1
............299155BA04 .................Centrifugal Switch (not shown)............................ .................................... 1
............2992A55A14 .................Capacitor (not shown).......................................... .................................... 1
75 ........2808B530C3 .................Motor Cable ......................................................... .................................... 1
76 ........TS-1490041 ..................Hex Cap Bolt........................................................M8x25......................... 4
77 ........TS-1550061 ..................Flat Washer..........................................................M8............................... 8
78 ........TS-1540061 ..................Hex Nut ................................................................M8............................... 4
79 ........10607970A1..................Motor Pulley......................................................... .................................... 1
80 ........2571MNC109................Parallel Key.......................................................... .................................... 1
81 ........TS-1524031 ..................Set Screw.............................................................M8x12......................... 1
83 ........12201501 ......................Wire Clip............................................................... .................................... 1
84 ........TS-1533042 ..................Pan Head Screw..................................................M5x12......................... 1
85 ........2807BB08C4.................Power Cable ........................................................ .................................... 1
87 ........DC1200-44....................On-Off Switch....................................................... .................................... 1
88 ........10908814 ......................Switch Box ........................................................... .................................... 1
89 ........TS-1533052 ..................Pan Head Screw..................................................M5x16......................... 3
90 ........10909012A1..................Pulley Cover Assy................................................ .................................... 1
92 ........2641BZDA40.................Round Head Screw..............................................M6x16......................... 4
95 ........10809502 ......................Center Pulley ....................................................... .................................... 1
96 ........BB-6202Z......................Ball Bearing.......................................................... .................................... 2
98 ........10609801 ......................Center Pulley Shaft.............................................. .................................... 1
99 ........VB-A28..........................V-Belt ...................................................................A28.............................. 1
101 ......TS-0680021 ..................Flat Washer..........................................................1/4".............................. 4
106 ......TS-0561052 ..................Hex Nut ................................................................1/2"-20UNF................. 1
112 ......10611201 ......................Chuck Key Holder................................................ .................................... 1
113 ......TS-1534042 ..................Pan Head Screw..................................................M6x12......................... 1
119 ......VB-A29..........................V-Belt ...................................................................A29.............................. 1
128 ......2653MBDE15................Tapping Screw..................................................... .................................... 2
131 ......CK-16............................Chuck Key............................................................ .................................... 1
137 ......10913701 ......................Switch Cover........................................................ .................................... 1
138 ......TS-1533042 ..................Pan Head Screw..................................................M5x12......................... 2
139 ......2852D55723..................Bulb Switch .......................................................... .................................... 1
140 ......10714001 ......................Motor Bar (left)..................................................... .................................... 1
147 ......10214704 ......................Protecting Rubber................................................ .................................... 1
149 ......2536MBE616 ................Spring Pin............................................................. .................................... 2
150 ......10916904 ......................I.D. Label.............................................................. .................................... 1
162 ......10916202 ......................Warning Label...................................................... .................................... 1
163 ......2658MZDU36................Drive Screw.......................................................... .................................... 8
165 ......10616519 ......................Speed Chart......................................................... .................................... 1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Index Part
No. No.
Description
Size
Qty.
169 ......11316904 ......................Nameplate............................................................ .................................... 1
601 ......TS-1533032 ..................Pan Head Machine Screw ...................................M5x10......................... 2
602 ......2504MZC005 ................Tooth Washer ...................................................... .................................... 2
607 ......TS-0720101 ..................Lock Washer........................................................7/16”............................ 2
610 ......TS-1503081 ..................Socket Head Cap Screw......................................M6x35......................... 2
611 ......10661102 ......................Seat...................................................................... .................................... 1
612 ......TS-1540081 ..................Hex Nut ................................................................M12............................. 1
613 ......10661301 ......................Scale Bolt............................................................. .................................... 1
614 ......13005701 ......................Nut........................................................................ .................................... 2
615 ......13005601 ......................Washer................................................................. .................................... 1
616 ......TS-1504051 ..................Hex Socket Cap Screw........................................M8x25......................... 1
617 ......10761701 ......................Set Ring ............................................................... .................................... 1
618 ......10661801 ......................Circular Nut.......................................................... .................................... 1
634 ......TS-1551081 ..................Lock Washer........................................................M12............................. 1
700 ......TS-152704 ....................Hex Wrench .........................................................3MM............................ 1
701 ......TS-152706 ....................Hex Wrench .........................................................5MM............................ 1
801 ......28065558U4..................Bulb Wire.............................................................. .................................... 2
903 ......2801ABRF04.................Strain Relief ......................................................... .................................... 2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WMH Tool Group
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|