Jasco Mouse HO97990 User Manual

Wireless Optical Mouse  
Instruction Manual  
HO97990 / 98150  
For technical support, contact Jasco at 1-800-654-8483 or  
Revision 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURE DESCRIPTIONS  
Eliminates the clutter of tangled cords  
Provides pinpoint precision on most surfaces and won’t wear out  
Goes to sleep when idle for a long time to extend battery life  
Battery Low LED illuminates when the battery is low  
Compatible with any USB port  
PACKAGE CONTENTS  
Wireless Optical Mouse  
USB Receiver  
Two AA Batteries  
User’s Manual  
SYSTEM REQUIREMENTS  
Pentium 133 MHz or higher processor  
Windows® or Mac compatible  
For Windows® 98 SE: minimum of 32 MB of RAM recommended  
For Windows® 2000, ME, XP: minimum of 64 MB of RAM  
recommended  
Minimum of 4MB of available hard disk space  
USB Port  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING YOUR MOUSE  
1. Disconnect the existing mouse.  
2. Connect the receiver’s USB plug to the USB Port on your  
computer.  
3. Place the receiver 8” (20cm) from any other electronic device  
such as your computer and monitor.  
4. Install the included 2 AA batteries into the battery compartment  
located on the bottom of your mouse. Position the batteries  
according to the diagram in the battery compartment.  
Low Battery LED  
Link Button  
On / Off Switch  
2 AA Batteries  
5. Turn on your computer and start your Operating System.  
6. Place your Wireless Optical Mouse within 3 feet (approximately 1  
meter) of the receiver for optimal communication.  
7. Move the mouse to ensure there is a good connection.  
8. If the mouse does not work, you may need to link your mouse.  
See the Trouble Shooting section for instructions.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
Optical mice do not work well on glass or highly reflective surfaces. If  
your mouse does not work properly, try a different surface such as a  
plain white piece of paper.  
POWER SAVING FEATURES  
1.  
After a period of inactivity, the Wireless Optical Mouse goes  
into sleep mode to save batteries. To wake the mouse, press  
any mouse button.  
2.  
3.  
The low battery LED located on the bottom of the mouse will  
illuminate when the batteries are low and need to be changed.  
There is an on/off switch located on the bottom of the mouse. If  
the mouse will be unused for an extended period of time or  
while traveling the mouse can be turned off to conserve the  
batteries. This will prevent the batteries from being used every  
time a mouse button is hit. The mouse must be turned back on  
before use.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
1. Linking the mouse  
¾
Press the Link button on the bottom of your receiver with a  
pen or paper clip.  
Receiver  
Link  
Button  
Mouse  
Link  
Button  
On / Off  
Switch  
¾
Being careful not to shine the light in your eyes, use a pen or  
paper clip to press the Link button on the bottom of your  
Wireless Optical Mouse. Move the mouse to ensure  
connection.  
2. Mouse Does Not Respond  
After a period of inactivity, the mouse goes into sleep mode to  
save batteries. To wake the mouse, press any mouse button.  
If the mouse has never worked:  
¾
Make sure the receiver is securely connected to your  
computer.  
¾
¾
Make sure you have correctly installed good batteries.  
Try to re-link the mouse using Troubleshooting step 1.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mouse Does Not Respond (Continued)  
¾
Make sure you have installed all Windows® updates and  
¾
Optical mice do not work well on glass or highly reflective  
surfaces. Try using your mouse on a different surface such as  
a plain white piece of paper.  
¾
Turn off your computer. Unplug the receiver from your  
computer. Wait 20 seconds. Plug the receiver into your  
computer. Turn your computer on. You may need to re-link  
the mouse using Troubleshooting step 1.  
3. Mouse does not work after replacing batteries  
¾
Make sure you have correctly inserted the new batteries,  
matching the battery polarity markings with the positive (+)  
and negative (-) symbols in the battery compartment.  
Re-link your mouse Troubleshooting step 1.  
¾
If your mouse still does not work after following these steps, please  
contact Jasco product support at 1-800-654-8483 or visit our website at  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
5 YEAR LIMITED WARRANTY  
Jasco Products Company warrants this product to be free from  
manufacturing defects for a period of five years from the original date  
of consumer purchase. This warranty is limited to the repair or  
replacement of this product only and does not extend to  
consequential or incidental damage to other products that may be  
used with this unit. This warranty is in lieu of all other warranties  
express or implied. Some states do not allow limitations on how long  
an implied warranty lasts or permit the exclusion or limitation of  
incidental or consequential damages, so the above limitations may  
not apply to you. This warranty gives you specific rights, and you  
may also have other rights which vary from state to state. If unit  
should prove defective within the warranty period, return prepaid with  
dated proof of purchase to:  
Jasco Products Company  
10 East Memorial Road  
Oklahoma City, OK 73114  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
Notice: Federal Communications Commission (FCC)  
requirements, Part 15  
This equipment has been tested and found to comply with the limits  
for a class B digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION: Any changes of modifications not expressly approved by  
the grantee of this device could void the users authority to operate  
the equipment. This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause  
undesired operation.  
is a trademark of  
General Electric Company  
and is used under license to  
Jasco Products Company LLC,  
10 E. Memorial Road,  
Oklahoma City, OK 73114.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Indesit Refrigerator IN CB 320 A I User Manual
Insignia DVD Player NS 7PDVDD User Manual
Jenn Air Dishwasher JDB1090AWB User Manual
Kenmore Coffeemaker 10090006 User Manual
Kenwood Home Security System NX 410 User Manual
Kenwood Stereo Amplifier KMF X9000 User Manual
Kenwood Stereo Receiver KRF V8010D User Manual
King Canada Saw KC 163SSC V User Manual
Klark Teknik Car Speaker DN9610 User Manual
Kodak Digital Camera Z712 IS User Manual