GE Model 19209
Wireless Door Chime Kit
Installation Instructions for Battery Operated
Wireless Door Chime Kit
Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips
screwdriver.
Included Hardware:
(2) Plastic screw anchors
(2) 4x20mm screws (for anchors)
(2) 3x20mm screws
(2) Double sided adhesive pads
The wireless door chime Kit has two components:
Chime (receiver)
Push-Button (Transmitter).
Chime Tune Setting
All wireless chimes may have more than one push button. The chime tune for
each push button is set with jumpers 7-9.
Single Push Button Kit: If you purchased a kit with a single push button, the
chime tune will be set to Ding Dong from the factory.
Dual Push Button Kit: If you purchased a kit with two push buttons, one push
button will be set to Ding Dong and the other push button will be set to
Westminster from the factory.
The following instructions explain how to change the tune on any wireless push
Download from Www.Somanuals.com. All Manuals Search And Download.
Parking the jumper on an open set of pins. The two jumpers on the left are in the
parked position.
Setting The House Security Code
Each chime component has jumpers for setting the house security code.
In most cases you will not need to change the factory settings for the
security code. If your chime activates intermittently or does not work at all,
you may be able to solve the problem by changing your security code.
Download from Www.Somanuals.com. All Manuals Search And Download.
The chime and pushbutton must be set to the same house security code for the
combination to operate together.
Note: The push button has 3 additional jumpers that are used to set the chime
tune that will play. The chime tune jumpers do not affect the house security code.
1. Remove power or batteries from the chime.
2. To remove the batteries from the pushbutton, open the pushbutton case
as shown below.
3. Locate the House Security Code door and screw located on the
back of the AC Chime. Remove the screw and take off the door.
4. Locate the chime and pushbutton jumpers shown below.
Download from Www.Somanuals.com. All Manuals Search And Download.
Push Button Jumpers
Chime Jumpers
5. Jumpers 1-6 are used to select 1 of 64 possible home security codes.
6. To change the house code, add or remove jumpers as needed. It is
recommended to change only one jumper at a time and then test the
system for proper operation. Positions 1-6 on the chime and pushbutton
must match exactly.
Push Button Mounting Instructions
Note: Avoid mounting the push button on metal surfaces, as it may result
in a reduced range of transmission. Do not mount in an area of rain (direct
weather.)
a. Removing the back cover
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Replacing the back cover
1. Push buttons are typically mounted at the same height as the door knob or
handle (between 36" and 44" above the floor).
2. Before mounting, choose a mounting location that is not farther than 150
feet from the chime unit location.
Not farther than 150 feet
Place push button where you would like to mount and test operation with
the chime as close to it’s final location as possible. If it works, mount
button here. Do not mount in an area of rain (direct weather.) If it does not
work, see TROUBLESHOOTING.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Use back cover of push button as a template to mark two screw holes.
4.
5.
Drill two holes with 3/32” drill in marked locations.
Secure back cover to the mounting surface with two supplied mounting
screws.
6.
7.
Press front housing onto back cover.
Test Operations, if chime does not work, see TROUBLESHOOTING.
Chime Unit Mounting Instructions
Note: Avoid mounting the push button on metal surfaces, as it may result
in a reduced range of transmission.
1.
2.
3.
4.
5.
Select chime mounting location.
Use the supplied chime template to mark mounting holes.
Drill ¼” holes at marked locations.
Insert supplied wall anchors into the holes.
Insert two of the supplied screws into the anchors, setting the screw heads
extending about 1/4" from mounting surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Place the chime unit’s keyhole slots over the screws and press down on
the chime unit to secure it.
Operation
1.
Slide power switch to “On” to turn on the chime.
2.
Gently press transmitter button to sound chime.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Chime doesn't work:
1.
2.
3.
Make sure push button switch is depressed and held for at least 1 second.
Make sure plastic tag is removed from battery.
Make sure house code switches 1-6 on chime and push button match
exactly.
4.
5.
6.
7.
Verify battery orientation in push button.
Try fresh batteries.
Make sure chime is not farther than 150 feet away from push button.
Ensure push button is not mounted on metal, near metal studs, or near the
floor.
Try a new location for the chime.
8.
Functional range may be adversely affected by one or more of the following
factors: weather, radio frequency interference, low transmitter battery and
obstructions between the transmitter and receiver.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
1. This device may not cause harmful interference, and
2. This device must accept interference received, including any interference that
may cause undesired operation.
For technical support contact Jasco Products Company at 1-800-654-8483
Made in China
is a trademark of
General Electric Company
and is used under license to
Jasco Products Company LLC,
311 N.W. 122nd Street,
Oklahoma City, OK 73114.
Rev. 1-07
19209
Download from Www.Somanuals.com. All Manuals Search And Download.
|