Jackson Dishwasher CREW 44 User Manual
CREW SERIES  
RACK CONVEYOR DISHMACHINES  
With WISR TM  
TECHNICAL MANUAL  
INSTALLATION MANUAL FOR EXPORT UNITS  
SERVICE MANUAL FOR DOMESTIC UNITS  
ELECTRICALLY HEATED MODELS:  
CREW 44  
CREW 66  
STEAM HEATED MODELS  
CREW 44S  
CREW 66S  
Jackson WWS, Inc.  
P.O. Box 1060, Hwy 25E  
Barbourville, KY USA  
1.606.523.9795  
Feb. 25, 2011  
P/N 07610‐003‐78‐18 (Revision D)  
www.jacksonwws.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Revision Revision  
Made By  
Applicable ECNs Details  
Letter  
Date  
A
B
07-27-10  
02-25-11  
CW/JC  
JC  
N/A  
Initial release of manual  
8183  
8186  
8187  
8177  
Transformer change for 208 Volt units.  
Drain handle operation & alignment change.  
Door splash shield addition.  
Rinse paddle switch operation.  
Initial release of 66” units, 44” Steam units &  
66” Steam units  
C
D
06-30-11  
03-28-13  
JC  
JC  
N/A  
Initial release of 23” & 30” unhooded side-  
loaders  
Changed Jackson Logo  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Speciꢀications  
Machine Dimensions  
Page 6  
Page 10  
Page 11  
Page 12  
Page 13  
Page 14  
Side Loader Dimensions  
Steam Booster Heater Dimensions  
Operating Parameters  
Notes Regarding Electrical Requirements  
Electrical Requirements  
Instructions  
Installation Instructions  
Curtain Installation Instructions  
Page 17  
Page 22  
Operating Instructions  
Delime Instructions  
Page 23  
Page 25  
Maintenance  
Troubleshooting  
Page 26  
Parts Section  
Control Box Components  
Overloads  
Page 27  
Page 29  
Page 30  
Page 31  
Page 32  
Page 33  
Page 34  
Page 35  
Page 36  
Page 37  
Page 38  
Page 39  
Page 40  
Page 42  
Page 44  
Page 46  
Page 47  
Page 48  
Miscellaneous Electrical Components  
Wash Heater and Heater Shroud Assemblies  
Pump Suction Assembly  
Wash Heaters  
Door Assembly  
Pre‐Wash Door Assembly  
Wash Door Spring Assembly  
Plumbing Assembly, Main Water Inlet  
Wash Tank Fill Assembly  
Pre‐Wash Tank Fill Assemblies  
Wash Manifold and Arm Assembly  
Pre‐Wash Manifold and Arm Assemblies  
Rinse Assembly  
Pawl Bar Assembly  
Pawl Bar Bracket Assembly  
Pawl Bar Gutter Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS (CONTINUED)  
Parts Section (Continued)  
Rack Paddle Assembly  
Rinse Paddle Assemblies  
Drain Assembly Parts  
Covers, Guards and Panels  
Brackets  
Page 49  
Page 50  
Page 51  
Page 52  
Page 53  
Page 54  
Page 55  
Page 56  
Page 57  
Page 59  
Page 62  
Page 63  
Page 64  
Page 65  
Miscellaneous Parts  
Ventilation Cowl Parts  
Ventilation Cowl for Unhooded Side‐Loader  
Drive Assembly  
Side‐Loaders  
Side‐Loader Drive Linkage  
Steam Heating Coil Assembly  
Booster Heater Option (Electric)  
Booster Heater Option (Steam)  
Electrical Diagrams and Schematics  
Booster Heater Schematic (3 Phase)  
Page 67  
Booster Heater Schematic (1 Phase, 12 KW)  
Booster Heater Schematic (1 Phase, 18 KW)  
Steam Booster Heater Schematic  
Page 68  
Page 69  
Page 70  
Page 71  
Page 72  
Page 73  
Page 74  
Page 75  
Page 76  
Page 77  
Page 78  
Page 79  
Page 80  
Temperature Board  
Schematic, Photo‐Cell Table Limit Switch  
Schematic, 44” (208‐230‐460/60/3 Phase)  
Schematic, 44” (208‐230/60/1 Phase)  
Schematic, 44” Steam (208‐230‐460/60/3 Phase)  
Schematic, 44” Steam (208‐230/60/1 Phase)  
Schematic, 66” (208‐230‐460/60/3 Phase)  
Schematic, 66” (208‐230/60/1 Phase)  
Schematic, 66” Steam (208‐230‐460/60/3 Phase)  
Schematic, 66” Steam (208‐230/60/1 Phase)  
Maintenance & Repair Centers  
Page 81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MACHINE DIMENSIONS ( 44” Left to Right)  
NOTE 1:  
THE MAXIMUM DOOR HEIGHT MAY BE  
REDUCED BY THE ADDITION OF OPTIONAL  
DOOR BRACKETS. MAXIMUM HEIGHTS OF  
91", 89" & 87" ARE AVAILABLE.  
W
E2  
E1  
NOTE 2:  
RA  
VENTILATION DUCT ADAPTERS ARE  
ADJUSTABLE FROM 51-1/2" TO 54".  
SAN  
NOTE 3:  
THE DRIVE ASSEMBLY AND GUARD  
MAY BE INSTALLED ON EITHER END  
OF THE UNIT. INSTALLATION ON THE  
UNLOAD END IS STANDARD. IF  
INSTALLED ON THE LOAD END,  
PLEASE ENSURE ANY SCRAP SINKS  
IN THE TABLING ARE AT AN ADEQUATE  
DISTANCE TO PROVIDE FOR CLEARANCE  
OF THE DRIVE ASSEMBLY.  
D
S*  
C*  
TABLE to TABLE  
3
44 in  
3
NOTE 4:  
4
in  
8
ALL VERTICAL DIMENSIONS MAY  
VARY DUE TO THE ADJUSTABLE  
FEET.  
63  
in  
8
1
51 in MIN  
2
V2  
V1  
(NOTE 2)  
23.50  
21 in  
11 in  
4 in  
E1  
E2  
W
E1  
E2  
5
20  
in  
8
W
RA  
SAN  
DET  
DET  
DET  
S*  
CP  
D
C*  
CP  
1
6
in  
1
(NOTE 4)  
3
(NOTE 4)  
(NOTE 4)  
8
(NOTE 4)  
3
in  
4
1
11 in  
14 in  
2
2
1
17 in  
1
10 in (NOTE 3)  
8
1
44 in  
8
8
* APPLIES TO STEAM HEATED UNITS  
** CHEMICAL SANITIZING UNITS ONLY  
E1  
E2  
W
D
MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)  
BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)  
MAIN INLET WATER CONNECTION (1/2 NPT‐F )  
DRAIN CONNECTION ( 1‐1/2” NPT‐F)  
RA RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)  
CP CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)  
S* STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)  
C* CONDENSATE RETURN (3/4” NPT‐F)  
DET DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)  
SAN** SANITIZER INLET TO RINSE (1/8” NPT‐F)  
V1 VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID  
V2 VENTILATION DUCT CONN. (UNLOAD END) 4” x 16” ID  
Page Created: 06‐30‐2011  
Revised: N/A  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MACHINE DIMENSIONS ( 44” Right to Left)  
NOTE 1:  
THE MAXIMUM DOOR HEIGHT MAY BE  
REDUCED BY THE ADDITION OF OPTIONAL  
DOOR BRACKETS. MAXIMUM HEIGHTS OF  
91", 89" & 87" ARE AVAILABLE.  
W
E2  
NOTE 2:  
E1  
D
RA  
VENTILATION DUCT ADAPTERS ARE  
ADJUSTABLE FROM 51-1/2" TO 54".  
4 in  
SAN  
NOTE 3:  
THE DRIVE ASSEMBLY AND GUARD  
MAY BE INSTALLED ON EITHER END  
OF THE UNIT. INSTALLATION ON THE  
UNLOAD END IS STANDARD. IF  
INSTALLED ON THE LOAD END,  
PLEASE ENSURE ANY SCRAP SINKS  
IN THE TABLING ARE AT AN ADEQUATE  
DISTANCE TO PROVIDE FOR CLEARANCE  
OF THE DRIVE ASSEMBLY.  
3
4
in  
8
TABLE to TABLE  
NOTE 4:  
S*  
C*  
ALL VERTICAL DIMENSIONS MAY  
VARY DUE TO THE ADJUSTABLE  
FEET.  
44 in  
3
63  
in  
8
5
51  
in  
8
5
23  
in  
(NOTE 2)  
V2  
8
V1  
1
21 in  
8
1
11 in  
8
1
4
in  
E1  
E2  
4
E1  
W
E2  
W
RA  
5
20  
SAN  
in  
8
DET  
DET  
S*  
CP  
DET  
C*  
D
CP  
S*  
3
1
3
1
in  
(NOTE 4)  
(NOTE 4)  
6
in  
(NOTE 4)  
(NOTE 4)  
in  
4
8
17 in  
1
8
14 in  
1
1
2
11 in  
2
3
(NOTE 3) 10 in  
4
8
8
1
44 in  
8
* APPLIES TO STEAM HEATED UNITS  
** CHEMICAL SANITIZING UNITS ONLY  
RA RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)  
E1  
E2  
W
D
MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)  
BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)  
MAIN INLET WATER CONNECTION (1/2 NPT‐F )  
DRAIN CONNECTION ( 1‐1/2” NPT‐F)  
CP CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)  
S* STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)  
C* CONDENSATE RETURN (3/4” NPT‐F)  
V1 VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID  
V2 VENTILATION DUCT CONN. (UNLOAD END) 4”x 16”ID  
DET DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)  
SAN** SANITIZER INLET TO RINSE (1/8” NPT‐F)  
Page Created: 06‐30‐2011  
Revised: N/A  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MACHINE DIMENSION (66” Left to Right)  
NOTE 1:  
THE MAXIMUM DOOR HEIGHT MAY BE  
REDUCED BY THE ADDITION OF OPTIONAL  
DOOR BRACKETS. MAXIMUM HEIGHTS OF  
91", 89" & 87" ARE AVAILABLE.  
W1  
E2  
RA  
E1  
W2  
W3***  
SAN**  
NOTE 2:  
VENTILATION DUCT ADAPTERS ARE  
ADJUSTABLE FROM 73-1/2" TO 76".  
NOTE 3:  
4 in  
D1  
D2  
THE DRIVE ASSEMBLY AND GUARD  
MAY BE INSTALLED ON EITHER END  
OF THE UNIT. INSTALLATION ON THE  
UNLOAD END IS STANDARD. IF  
INSTALLED ON THE LOAD END,  
PLEASE ENSURE ANY SCRAP SINKS  
IN THE TABLING ARE AT AN ADEQUATE  
DISTANCE TO PROVIDE FOR CLEARANCE  
OF THE DRIVE ASSEMBLY.  
S*  
C*  
TABLE to TABLE  
66 in  
85 in  
1
NOTE 4:  
2
ALL VERTICAL DIMENSIONS MAY  
VARY DUE TO THE ADJUSTABLE  
FEET.  
1
73 in MIN  
2
1
23 in  
(NOTE 2)  
V1  
2
V2  
21 in  
1
11 in  
8
7
1
10  
in  
4
in  
4
8
E1  
E2  
E1  
W2  
E2  
W1  
W3***  
W1  
RA  
SAN**  
5
20  
in  
8
DET  
DET  
S*  
D2  
CP  
C*  
D1  
CP  
3
5
1
3
in  
7
in  
(NOTE 4)  
6
in  
(NOTE 4)  
(NOTE 4)  
4
8
8
1
1
1
14 in  
33 in  
17 in  
2
2
8
1
1
10 in (NOTE 3)  
66 in  
8
8
* APPLIES TO STEAM HEATED UNITS  
** CHEMICAL SANITIZING UNITS ONLY  
*** PRE-WASH COLD WATER THERMOSTAT OPTION ONLY  
E1  
E2  
MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)  
BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)  
MAIN INLET WATER CONNECTION (1/2 NPT‐F )  
PRE‐WASH INLET WATER CONN. (1/2 NPT‐F)  
SAN** SANITIZER INLET TO RINSE (1/8” NPT‐F)  
RA  
CP  
S*  
RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)  
CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)  
STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)  
CONDENSATE RETURN (3/4” NPT‐F)  
W1  
W2  
W3*** PRE‐WASH COLD WATER CONN. (1/2 NPT‐F)  
C*  
D1  
D2  
DRAIN CONNECTION, WASH ( 1‐1/2” NPT‐F)  
V1  
V2  
VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID  
VENTILATION DUCT CONN. (UNLOAD END) 4”x 16”ID  
DRAIN CONNECTION, PRE‐WASH ( 1‐1/2” NPT‐F)  
DET DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)  
Page Created: 06‐30‐2011  
Revised: N/A  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MACHINE DIMENSION (66” Right to Left)  
NOTE 1:  
THE MAXIMUM DOOR HEIGHT MAY BE  
REDUCED BY THE ADDITION OF OPTIONAL  
DOOR BRACKETS. MAXIMUM HEIGHTS OF  
91", 89" & 87" ARE AVAILABLE.  
E1  
RA W1 E2  
W2  
D2  
W3***  
SAN**  
NOTE 2:  
VENTILATION DUCT ADAPTERS ARE  
ADJUSTABLE FROM 73-1/2" TO 76".  
4 in  
D1  
NOTE 3:  
THE DRIVE ASSEMBLY AND GUARD  
MAY BE INSTALLED ON EITHER END  
OF THE UNIT. INSTALLATION ON THE  
UNLOAD END IS STANDARD. IF  
INSTALLED ON THE LOAD END,  
PLEASE ENSURE ANY SCRAP SINKS  
IN THE TABLING ARE AT AN ADEQUATE  
DISTANCE TO PROVIDE FOR CLEARANCE  
OF THE DRIVE ASSEMBLY.  
S*  
C*  
TABLE to TABLE  
3
66 in  
1
4
in  
8
85 in  
2
1
NOTE 4:  
73 in  
2
ALL VERTICAL DIMENSIONS MAY  
VARY DUE TO THE ADJUSTABLE  
FEET.  
(NOTE 2)  
1
23 in  
2
21 in  
V2  
V1  
1
11 in  
8
1
7
4
in  
10  
in  
4
8
E1  
E2  
E1  
W2  
W1  
E2  
W3***  
W1  
RA  
SAN**  
DET  
DET  
S*  
D2  
C*  
D1  
CP  
3
1
3
in  
6
in  
(NOTE 4)  
(NOTE 4)  
(NOTE 4)  
CP  
4
8
5
5
7
in  
11  
in  
8
1
8
17 in  
8
1
10 in (NOTE 3)  
8
1
29 in  
2
1
66 in  
8
* APPLIES TO STEAM HEATED UNITS  
** CHEMICAL SANITIZING UNITS ONLY  
*** PRE-WASH COLD WATER THERMOSTAT OPTION ONLY  
E1  
E2  
MAIN ELECTRICAL CONNECTION (1.375” DIA HOLE)  
BOOSTER HEATER ELECT. CONNECTION (1.375” DIA)  
MAIN INLET WATER CONNECTION (1/2 NPT‐F )  
PRE‐WASH INLET WATER CONN. (1/2 NPT‐F)  
SAN** SANITIZER INLET TO RINSE (1/8” NPT‐F)  
RA  
CP  
S*  
RINSE AID CONNECTION TO RINSE (1/8” NPT‐F)  
CONDUCTIVITY PROBE ACCESS (.875” DIA HOLE)  
STEAM TO WASH TUB HEATING COIL (3/4” NPT‐F)  
CONDENSATE RETURN (3/4” NPT‐F)  
W1  
W2  
W3*** PRE‐WASH COLD WATER CONN. (1/2 NPT‐F)  
C*  
D1  
D2  
DRAIN CONNECTION, WASH ( 1‐1/2” NPT‐F)  
V1  
V2  
VENTILATION DUCT CONN. (LOAD END) 4” x 16” ID  
VENTILATION DUCT CONN. (UNLOAD END) 4”x 16”ID  
DRAIN CONNECTION, PRE‐WASH ( 1‐1/2” NPT‐F)  
DET DETERGENT BULKHEAD ACCESS (.875” DIA HOLE)  
Page Created: 06‐30‐2011  
Revised: N/A  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
SIDE LOADER DIMENSIONS  
23" R-L UNHOODED  
23" L-R UNHOODED  
SIDE-LOADER  
SIDE-LOADER  
30.32  
30.32  
29.00  
29.00  
16.35  
16.35  
23.00  
23.00  
DIMENSION IS 30.00" FOR THE  
30" UNHOODED SIDE-LOADER  
DIMENSION IS 30.00" FOR THE  
30" UNHOODED SIDE-LOADER  
ADJUSTABLE VENTILATION  
DUCT ADAPTER  
ADJUSTABLE VENTILATION  
DUCT ADAPTER  
VENTILATION SCOOP  
VENTILATION SCOOP  
VENTILATION COWL  
WITH CUTOUT FOR  
L-R UNITS  
VENTILATION COWL  
WITH CUTOUT FOR  
R-L UNITS  
22.00  
22.00  
10.00  
10.00  
ELECTRICAL  
CONDUIT  
ELECTRICAL  
CONDUIT  
+1.00  
34.00  
-1.00  
+1.00  
-1.00  
34.00  
SIDE-LOADER  
DRAIN HOSE  
SIDE-LOADER  
DRAIN HOSE  
Page Created: 06‐30‐2011  
Revised: N/A  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
STEAM BOOSTER HEATER DIMENSIONS  
BOOSTER HEATER STEAM CONSUMPTION  
33.69  
1
Temperature Rise  
(Degrees Fahrenheit)  
40  
50  
60  
70  
80  
20 in  
4
W1  
Steam Consumption  
(lbm/hr)  
30  
37  
45  
52  
59  
Based upon a Steam Inlet Pressure of 15-25psig  
S
E
1
10 in  
8
3
W2  
W2  
1
in  
4
PW  
PS  
PS  
PW  
PS  
S
S
PW  
W1  
W2  
E
3
1
3
in  
7
in  
8
2
3
19  
in  
5
7
8
8
in  
8
in  
8
8
1
C
E
20 in  
8
C
22 in  
22 in  
5
28  
in  
8
E
MAIN ELECTRICAL CONNECTION (7/8” DIA HOLE)  
MAIN INLET WATER CONNECTION (3/4 NPT‐F )  
WATER OUTLET CONNECTION (3/4 NPT‐F)  
WATER PRESSURE RELIEF OUTLET (3/4 NPT‐F)  
STEAM PRESSURE RELIEF OUTLET (1” NPT‐F)  
STEAM SUPPLY TO BOOSTER (1” NPT‐F)  
W1  
W2  
PW  
PS  
S
C
STEAM CONDENSATE CONNECTION (3/4 NPT‐F)  
Page Created: 06‐30‐2011  
Revised: N/A  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
Operating Parameters  
Model Designation:  
Operating Capacity:  
Racks per Hour  
Dishes per Hour  
Glasses per Hour  
44”  
66”  
44”Steam  
66”Steam  
218  
3488  
7848  
218  
3488  
7848  
218  
3488  
7848  
218  
3488  
7848  
Tank Capacity (gallons):  
Wash Tank  
Pre‐Wash Tank  
35.6  
N/A  
35.6  
15.8  
35.6  
N/A  
35.6  
15.8  
Electrical Loads (as applicable):  
Wash Motor HP  
Drive Motor HP  
3.0  
0.25  
N/A  
3.0  
0.25  
2.0  
3.0  
0.25  
N/A  
3.0  
0.25  
2.0  
Pre‐Wash Motor HP  
Wash Heater KW  
15 or 18  
18  
N/A  
N/A  
NOTE: Always refer to the machine data plate for speciꢀic electrical and water requirements. The  
material provided on this page is for reference only and is subject to change without notice.  
HOT WATER SANITIZING  
Water Temperatures (Fahrenheit):  
Pre‐Wash Temperature (Recommended) N/A  
Minimum Wash Temperature  
Minimum Rinse Temperature  
Incoming Water Temperature  
12 KW Booster  
110‐140  
160  
N/A  
160  
180  
110‐140  
160  
180  
160  
180  
180  
140  
110  
180  
140  
110  
180  
N/A  
N/A  
180  
N/A  
N/A  
180  
18 KW Booster  
No Booster  
CHEMICAL SANITIZING  
Water Temperatures (Fahrenheit):  
Pre‐Wash Temperature (Recommended) N/A  
Minimum Wash Temperature  
Minimum Rinse Temperature  
Incoming Water Temperature  
12 KW Booster  
110‐120  
120  
120  
N/A  
120  
120  
110‐120  
120  
120  
120  
120  
80  
50  
120  
80  
50  
120  
N/A  
N/A  
120  
N/A  
N/A  
120  
18 KW Booster  
No Booster  
Other Water Requirements:  
Water Flow Pressure (PSIG)  
Flow Rate Minimum (GPM)  
Water Line Size (NPT)  
Drain Line Size (NPT)  
15  
1.18  
1/2”  
1‐1/2”  
15  
15  
1.18  
1/2”  
1‐1/2”  
15  
1.18  
1/2”  
1‐1/2”  
1.18  
1/2”  
1‐1/2”  
Steam Requirements  
Steam Line for Wash Tank (NPT)  
Steam Flow Pressure (PSIG)  
Consumption @ 15 PSIG (lbm/hr)  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
3/4”  
10‐20  
60  
3/4”  
10‐20  
60  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
Notes Regarding Electrical Requirements  
All electrical ratings provided in this manual are for reference only. Always refer to the machine data plate  
to get the exact electrical information for your machine. All electrical work performed on machines  
should be done in accordance with applicable local, state, territorial and national codes. Work should  
only be performed by qualiꢀied electricians and authorized service agents. A list of authorized Service Agen‐  
cies is located in the back of this manual.  
Note that all electrical wiring used in the dish‐machine must be rated, at a minimum, for 100C (212F).  
Furthermore, use copper conductors only.  
Where applicable, heating element amperage draws have been adjusted for the assumed input voltage. Jack‐  
son assumes incoming voltages will be either 208, 230 or 460 volts. Some of the heating elements used in  
our machines are actually rated for other voltages, such as 240 or 480 volts. Always verify the amperage  
draw of the machine in operation when sizing circuit protection.  
If your machine is equipped with the optional rinse heater, note the rinse heater has its own electrical con‐  
nection and therefore requires a separate service. Amperage loads for motors and heaters are called out on  
the machine data plate for the installation/service technician.  
The electrical conꢀigurations of the machines are as follows:  
Available Electrical Characteristics:  
 208 volt, 60 Hz, single phase  
 230 volt, 60 Hz, single phase  
 208 volt, 60 Hz, three phase  
 230 volt, 60 Hz, three phase  
 460 volt, 60 Hz, three phase  
Available Wash Tank Heaters:  
 15KW (standard for CREW 44)  
 18KW (optional for CREW 44, standard for CREW 66)  
Available Rinse Heaters (“Booster Heaters”):  
 None (standard)  
 12KW (40F rise in temperature)  
 18KW (70F rise in temperature)  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
Electrical Requirements for 44” Units  
44” with 15 kW Wash Heater  
Wash  
Motor  
Amps  
Drive  
Motor  
Amps  
Wash  
Heater  
Amps  
Volts  
Phase Freq  
FLA  
MCA  
MOP  
208  
230  
240  
208  
230  
240  
460  
480  
1
1
1
3
3
3
3
3
60  
60  
60  
60  
60  
60  
60  
60  
10.0 A  
10.0 A  
10.0 A  
8.6 A  
8.4 A  
8.4 A  
4.2 A  
4.2 A  
1.8 A  
1.8 A  
1.8 A  
1.1 A  
1.1 A  
1.1 A  
0.6 A  
0.6 A  
72.1 A  
*59.9 A  
62.5 A  
41.6 A  
*34.6 A  
36.1 A  
**17.3 A  
18.1 A  
83.9 A  
71.7 A  
74.3 A  
51.3 A  
44.1 A  
45.6 A  
22.1 A  
22.9 A  
86.4 A  
74.2 A  
76.8 A  
53.5 A  
46.2 A  
47.7 A  
23.2 A  
24.0 A  
96.4 A  
84.2 A  
86.8 A  
62.1 A  
54.6 A  
56.1 A  
27.4 A  
28.2 A  
44” with 18 kW Wash Heater  
Wash  
Drive  
Motor  
Amps  
Wash  
Heater  
Amps  
Volts Phase Freq  
Motor  
Amps  
FLA  
MCA  
MOP  
208  
230  
240  
208  
230  
240  
460  
480  
1
1
1
3
3
3
3
3
60  
60  
60  
60  
60  
60  
60  
60  
10.0 A  
10.0 A  
10.0 A  
8.6 A  
8.4 A  
8.4 A  
4.2 A  
4.2 A  
1.8 A  
1.8 A  
1.8 A  
1.1 A  
1.1 A  
1.1 A  
0.6 A  
0.6 A  
86.5 A  
*71.9 A  
75.0 A  
50.0 A  
*41.5 A  
43.4 A  
**20.8 A  
21.7 A  
98.3 A  
83.7 A  
86.8 A  
59.7 A  
51.0 A  
52.9 A  
25.6 A  
26.5 A  
100.8 A  
86.2 A  
89.3 A  
61.9 A  
53.1 A  
55.0 A  
26.7 A  
27.6 A  
110.8 A  
96.2 A  
99.3 A  
70.5 A  
61.5 A  
63.4 A  
30.9 A  
31.8 A  
44” Steam  
Wash  
Motor  
Amps  
Drive  
Motor  
Amps  
Volts  
Phase Freq  
FLA  
MCA  
MOP  
208  
230  
208  
230  
460  
1
1
3
3
3
60  
60  
60  
60  
60  
10.0 A  
10.0 A  
8.6 A  
1.8 A  
1.8 A  
1.1 A  
1.1 A  
0.6 A  
11.8 A  
11.8 A  
9.7 A  
14.3 A  
14.3 A  
11.9 A  
11.6 A  
5.9 A  
24.3 A  
24.3 A  
20.5 A  
20.0 A  
10.1 A  
8.4 A  
9.5 A  
4.2 A  
4.8 A  
* Denotes 240 Volt heating elements that have been down‐rated when 230 Volts is applied.  
** Denotes 480 Volt heating elements that have been down‐rated when 460 Volts is applied.  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
Electrical Requirements for 66” Units  
66” with 18 kW Wash Heater  
Pre‐Wash  
Motor  
Amps  
Wash  
Motor  
Amps  
Drive  
Motor  
Amps  
Wash  
Heater  
Amps  
Volts Phase Freq  
FLA  
MCA  
MOP  
208  
230  
240  
208  
230  
240  
460  
480  
1
1
1
3
3
3
3
3
60  
60  
60  
60  
60  
60  
60  
60  
10.2 A  
9.4 A  
9.4 A  
6.8 A  
6.4 A  
6.4 A  
3.2 A  
3.2 A  
10.0 A  
10.0 A  
10.0 A  
8.6 A  
8.4 A  
8.4 A  
4.2 A  
4.2 A  
1.8 A  
1.8 A  
1.8 A  
1.1 A  
1.1 A  
1.1 A  
0.6 A  
0.6 A  
86.5 A  
*71.9 A  
75.0 A  
50.0 A  
*41.5 A  
43.4 A  
**20.8 A  
21.7 A  
108.5 A  
93.1 A  
96.2 A  
66.5 A  
57.4 A  
59.3 A  
28.8 A  
29.7 A  
111.1 A  
95.6 A  
98.7 A  
68.7 A  
59.5 A  
61.4 A  
29.9 A  
30.8 A  
121.3 A  
105.6 A  
108.7 A  
77.3 A  
67.9 A  
69.8 A  
34.1 A  
35.0 A  
66” Steam  
Pre‐Wash  
Motor  
Amps  
Wash  
Motor  
Amps  
Drive  
Motor  
Amps  
Volts  
Phase Freq  
FLA  
MCA  
MOP  
208  
230  
208  
230  
460  
1
1
3
3
3
60  
60  
60  
60  
60  
10.2 A  
9.4 A  
6.8 A  
6.4 A  
3.2 A  
10.0 A  
10.0 A  
8.6 A  
1.8 A  
1.8 A  
1.1 A  
1.1 A  
0.6 A  
22.0 A  
21.2 A  
16.5 A  
15.9 A  
8.0 A  
24.6 A  
23.7 A  
18.7 A  
18.0 A  
9.1 A  
34.8 A  
33.7 A  
27.3 A  
26.4 A  
13.3 A  
8.4 A  
4.2 A  
* Denotes 240 Volt heating elements that have been down‐rated when 230 Volts is applied.  
** Denotes 480 Volt heating elements that have been down‐rated when 460 Volts is applied.  
Page Created: 02‐25‐2011  
Revised: N/A  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
Electrical Requirements for Booster Tanks  
40° F Rise ‐ 12 KW Booster  
Rinse  
Heater  
Volts Phase Freq  
FLA  
Amps  
57.7 A  
47.9 A  
33.3 A  
27.7 A  
13.8 A  
208  
230  
208  
230  
460  
1
1
3
3
3
60  
60  
60  
60  
60  
57.7 A  
47.9 A  
33.3 A  
27.7 A  
13.8 A  
70° F Rise ‐ 18 KW Booster  
Rinse  
Volts Phase Freq  
Heater  
Amps  
FLA  
208  
230  
208  
230  
460  
1
1
3
3
3
60  
60  
60  
60  
60  
82.7 A  
71.9 A  
47.7 A  
41.5 A  
20.7 A  
82.7 A  
71.9 A  
47.7 A  
41.5 A  
20.7 A  
Note: 0n the 208 volt machines, the rinse heater is actually rated at 17.2 KW  
Page Created: 05‐04‐2010  
Revised: N/A  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
INSTALLATION INSTRUCTIONS  
VISUAL INSPECTION: Before installing the unit, check the container and the machine for damage. A  
damaged container may be an indication there is possible damage to the product. If there is any type of dam‐  
age to both the container and the unit, DO NOT THROW AWAY THE CONTAINER. The dish‐machine has  
been previously inspected at the factory and is expected to arrive to you in new, undamaged condition.  
However, rough handling by carriers or others may result in damage to the unit while it is in transit. If such  
a situation occurs, DO NOT RETURN THE UNIT TO THE MANUFACTURER. Instead, contact the carrier and  
ask them to send a representative to the site to inspect the damage. You should request that an inspection  
report be completed. You must contact the carrier within 48 hours of receiving the machine in order to re‐  
port possible freight damage. You are also encouraged to contact the dealer through which you purchased  
the unit.  
UNPACKING THE MACHINE: The machine should be unboxed and removed from the pallet prior to  
installing. Also remove the wooden lift beams and their associated brackets after the unit has been posi‐  
tioned. Open the front door and remove all of the materials from the inside. Once unpacked, verify there are  
no missing parts to the best of your ability. If you discover a part is missing, contact the manufacturer imme‐  
diately.  
LEVEL THE DISHMACHINE: The dish‐machine is designed to operate while level. This is important to  
prevent any damage to the machine during operation and to ensure the best results possible. The unit comes  
equipped with adjustable bullet feet, which can be turned using a pair of pliers. Verify the unit is level from  
front to back and side to side prior to making any electrical or plumbing connections.  
PLUMBING THE MACHINE: All plumbing connections must be made to adhere to local, state, territorial  
and national codes. The installing plumber is responsible for ensuring the incoming water lines are ꢀlushed  
of debris prior to connecting to the machine. Note that chips and materials from cutting processes can be‐  
come lodged in the solenoid valves and prevent them from opening or closing. Any valves that are found to  
be fouled or defective because of foreign matter left in the water line, and any subsequent water damage, are  
not the responsibility of the manufacturer.  
Water hardness should be a maximum of 6 grains per gallon. Hard water should be treated prior to be  
used by the machine. Iron in the water line can cause staining. A ꢀilter designed to remove iron from the wa‐  
ter supply is highly recommended for supplies in excess of 0.1 ppm.  
Your dish‐machine comes with a Water Pressure Regulating Valve. The unit utilizes a ꢀlow pressure of  
15 PSI for the incoming water line. Do not confuse static pressure with ꢀlow pressure. Static pressure is the  
pressure when there is no ꢀlow and the valves are closed; ꢀlow pressure is when the water is running into  
the machine. The WPRV should be adjusted to the proper ꢀlow pressure at a minimum.  
The water supply line shall be 1/2” NPT minimum and must be able to provide water at the minimum  
temperature indicated on the machine data plate.  
It is recommended a shut‐off valve be installed to allow isolating the dish‐machine from the water sys‐  
tem in the event maintenance or other activities require it. Also, it is suggested that a shock absorber be in‐  
Page Created: 05‐04‐2010  
Revised: N/A  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
INSTALLATION INSTRUCTIONS (CONTINUED)  
stalled on the incoming water line. This prevents water hammer (hydraulic shock), induced by the solenoid  
valve as it operates, from causing damage to the equipment.  
CONNECTING THE DRAIN LINE: The drain for the unit is a gravity discharge drain. All piping to the  
machine drain must be a minimum 1‐1/2” NPT AND SHALL NOT BE REDUCED. There must also be an air  
gap between the machine drain line and the ꢀloor sink or drain. If a grease trap is required by code, it should  
have a ꢀlow capacity of 30 gallons. 44” units have one drain connection point. 66” units have two points.  
STEAM LINE CONNECTIONS: Some machines covered in this manual are designed to use low pressure  
steam as a source of heat for the wash tank. Those machines come with lines by which an outside source of  
steam (i.e. steam booster) is connected. Connect all steam lines from the booster to the machine in accord‐  
ance with the booster manufacturer’s instructions. Ensure that all applicable codes and regulations are ad‐  
hered to. See the machine data plate for information related to steam ꢀlow requirements.  
ELECTRICAL POWER CONNECTIONS: All electrical connections are to be made in accordance with ap‐  
plicable portions of local, state, territorial and national codes.  
DISCONNECT ELECTRICAL POWER SUPPLIES AND TAG OUT IN ACCORDANCE WITH APPROPRIATE  
PROCEDURES AND CODES AT THE DISCONNECT SWITCH TO INDICATE YOU ARE WORKING ON THAT CIR-  
CUIT.  
This manual provides reference information regarding electrical requirements and loads, but that infor‐  
mation may change without notice. Always refer to the machine data plate for voltage requirements, ma‐  
chine voltage, total amperage load and serial number. If you cannot read your data plate because it has been  
damaged, you should contact the manufacturer.  
The main power terminal blocks (for the dish‐machine and for the rinse booster heater, if applicable)  
are located at the top of the machine. You will have to remove the top cover to access these connections.  
Route incoming power lines within conduit that will connect via ꢀittings to the pre‐punched holes in the  
back of the unit. Install power and ground wires to lugs as indicated by the appropriate decals in the control  
box. Use copper conductors only. Use of a anti‐oxidation agent is permissible on the power connections.  
Tighten all connections.  
Verify the incoming voltage matches the voltage indicated on the decal next to the incoming power pre‐  
punched hole.  
Please note the dish‐machine has a separate power connection from the rinse booster heater and the  
circuit protection requirements are different for each. Refer to the machine data plate for information on  
minimum circuit protection.  
DISHMACHINE VENTILATION: The dish‐machine should be located with provisions for venting into an  
adequate exhaust hood or ventilation system. This is essential to permit efꢀicient removal of the condensa‐  
tion exhaust. Ensure the exhaust system is acceptable in accordance with applicable codes and standards.  
Page Created: 05‐04‐2010  
Revised: N/A  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
INSTALLATION INSTRUCTIONS (CONTINUED)  
Note: any damage that is caused by steam and/or moisture due to improper ventilation is NOT  
covered under the warranty.  
The dish‐machine has the following ventilation requirements:  
 Load End: 200 CFM  
 Unload End: 200 CFM  
The exhaust system must be sized to handle this volume for the dish‐machine to operate in the manner  
it was designed to.  
THERMOSTATS: The thermostats on your unit have been set at the factory for the wash tank. They  
should only be adjusted by an authorized service agent.  
CHEMICAL FEEDER EQUIPMENT: Your dish‐machine DOES NOT COME WITH AN INTEGRAL CHEMI‐  
CAL SUPPLY/FEEDER SYSTEM. You must connect the unit to a third party chemical dispenser that meets the  
requirements of NSF Standard 29 for the machine to operate correctly.  
You should contact your chemical supplier about connecting a dispenser to your dish‐machine. Chemi‐  
cal dispensers must be set for the type and concentration of chemicals being used and there are several fac‐  
tors that have to be taken into account.  
Detergent usage and water hardness are two factors that contribute greatly to how efꢀiciently your dish  
machine will operate. Using the proper amount of detergent can become, in time, a source of substantial sav‐  
ings. A qualiꢀied water treatment specialist can explain in detail to you what is needed to gain the maximum  
efꢀiciency from your detergent.  
The dish‐machine is able to operate in either hot water sanitizing mode or chemical sanitizing mode.  
Your unit should be clearly marked above the data plate as to the mode it is in. If you cannot determine this,  
contact the manufacturer immediately for assistance.  
It is important to remember that if you decide to operate the unit in chemical sanitizing mode, you must  
ensure an appropriate chlorine‐based sanitizer is used in the ꢀinal rinse line.  
Page Created: 05‐04‐2010  
Revised: N/A  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
INSTALLATION INSTRUCTIONS (CONTINUED)  
DETERGENT INJECTION POINT.  
ANOTHER BULKHEAD PLUG  
IS PROVIDED ON THE LEFT SIDE  
OF THE UNIT  
ADJUSTABLE BULLET FEET  
1-1/2" NPTF DRAIN CONNECTION  
BULKHEAD OPENING FOR  
CONDUCTIVITY PROBE  
SHOWN FROM REAR OF LEFT TO RIGHT UNIT.  
RIGHT TO LEFT UNIT IS MIRRORED  
CHEMICAL TUBE  
INSERTION POINT  
875"  
BOOSTER HEATER  
ELECTRICAL CONNECTION  
OPENING  
1.375"  
INLET WATER FITTING  
1/2" NPTF  
MAIN ELECTRICAL  
CONNECTION OPENING  
1.375"  
Page Created: 05‐04‐2010  
Revised: N/A  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
INSTALLATION INSTRUCTIONS (CONTINUED)  
ELECTRICAL CONNECTION POINTS FOR TABLE LIMIT SWITCH,  
VENTILATION FAN SIGNAL & CHEMICAL DISPENSING SYSTEMS  
SIGNAL BOARD IS LOCATED IN THE MAIN CONTROL  
BOX BEHIND THE LOWER DRESS PANEL  
CONNECTION FOR  
REMOVE THIS JUMPER  
WIRE TO ALLOW FOR  
TABLE LIMIT SWITCH  
CONNECTIONS  
DETERGENT  
DISPENSER  
FROM DOOR SWITCH  
CONNECTION POINT  
FOR VENT FAN SIGNAL  
RINSE AID & SANITIZER  
CONNECTION SIGNALS  
TABLE LIMIT  
SWITCH  
CONNECTION  
TO PLC  
CHEMICAL DISSPENSER TUBE CONNECTION POINTS TO RINSE INJECTOR  
P: PRESSURE SWITCH (1/4” NPT)  
S: SANITIZER (1/8” NPT)  
R: RINSE AID (1/8” NPT)  
Page Created: 05‐04‐2010  
Revised: N/A  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
CURTAIN INSTALLATION INSTRUCTIONS  
You will ꢀind decals on the unit marking the locations for the placement of curtains inside the machine, start‐  
ing from the load end and going all the way to the unload end. The illustrations below indicates the size of  
the curtain to be placed on the curtain hooks provided. If you are missing any of the curtain components, it  
is very important you obtain replacement parts in order to make sure your unit runs correctly. Curtains are  
used to control the air currents inside your unit and they greatly assist in maintaining the heat necessary to  
keep energy costs down.  
DETERMINING CONVEYOR DIRECTION: Your dish‐machine will be conꢀigured for either Left to Right or  
Right to Left operation. Direction is always from the Load End to the Unload End, as shown in the examples.  
`
44” Right to Left  
44” Left to Right  
XL  
S
L
L
XL  
XL  
L
L
S
XL  
Unload  
Unload  
Load  
Load  
66” Right to Left  
XL  
L
L
S
L
S
L
XL  
Unload  
Load  
66” Left to Right  
XL  
S
L
S
L
XL  
Load  
Unload  
IMPORTANCE OF PROPER CURTAIN PLACEMENT: The curtains inside the dish‐machine are required to  
be installed in a particular fashion. Note the approximate locations for each type of curtain in the above  
illustrations. S=Short, L=Long & XL=Extra Long. See the chart below for actual curtain lengths and part  
numbers. Note the XL Curtain and Curtain Rod difference for the Load End when a Side‐Loader Option is  
present  
Legend  
Length Part Number  
Side‐Loader Option  
Length Part Number  
S
L
12”  
19”  
08415‐131‐73‐44  
08415‐002‐14‐41  
XL (Load End Only) 24.25” 08415‐003‐84‐88  
Curtain Rod  
(Load End Only)  
05700‐003‐84‐57  
XL  
24.25” 08415‐002‐47‐37  
Curtain Rod 20.50” 05700‐003‐77‐52  
Page Created: 05‐04‐2010  
Revised: 06‐27‐2011  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
OPERATION INSTRUCTIONS  
PREPARATION: Before proceeding with the start‐up of the unit, verify the following:  
 The drain stopper is installed;  
 The strainers are installed;  
 The pawl bar is installed and secure;  
 The actuator switches move with relative freedom and do not bind;  
 The curtains are installed correctly  
POWER UP: To place the unit in standby, press the Start Button on the front of the machine.  
 The unit will automatically determine if there is a proper water level in the wash tank. If not, the  
unit will begin to ꢀill until the appropriate level is reached.  
 If the wash tank temperature is not at the minimum level for the mode of operation, the wash heat‐  
er will energize. Refer to the machine data plate for a better understanding of the minimum temper‐  
atures needed to operate the unit correctly. It may take several minutes for the wash tank to heat  
up, depending on the initial temperature of the water.  
 If your machine is equipped with a rinse booster option, note the booster shall turn on when the  
unit turns on.  
 If your machine is heated with a steam booster, then you will need to turn on the steam booster in  
accordance with the manufacturer’s instructions.  
 It is important that you do not attempt to start the unit until:  
 The unit stops ꢀilling;  
 The unit has reached the appropriate wash tank temperature.  
FIRST RACK: The ꢀirst rack of ware that you place into the unit usually has the effect of very quickly  
reducing the temperature of the wash tank. This is because you are introducing cold materials into the dish‐  
machine environment and the unit has to circulate water to get the heating cycle going. You may have to run  
the ꢀirst rack through the unit again. Any time the unit has not been operated for an extended period of time  
this is possible, but unlikely. This is usually dependent on the type of ware you are using, its temperature  
and the ambient temperature of the kitchen area. Always observe the temperatures of the wash and rinse  
when ꢀirst starting the unit to ensure proper operation.  
WARE PREPARATION: Proper preparation of ware is essential for the smooth, efꢀicient operation of  
your dish‐machine. If done properly, you can expect to have fewer re‐washes and use substantially less de‐  
tergent. Any ware placed inside the machine should have all solid food waste and scraps removed. It is rec‐  
ommended that ware also be sprayed down prior to entry into the dish‐machine.  
Place cups and glasses upside down in racks so they do not hold water during the cycle. Presoak ꢀlat‐  
ware in warm water to assist in getting stuck‐on material off. Load plates and saucers in the same direction  
(with the surface food is placed on facing towards the unload end of the machine).  
WASHING A RACK OF WARE: The dish‐machine is designed to wash ware placed in a rack. Under no  
circumstance should any materials be placed inside the unit that have not been properly secured into a dish  
rack.  
To start the cycle, gently push the rack into the unit on the load end. Once the wash actuator has moved  
sufꢀiciently, the unit will automatically begin to convey the dish rack through the unit. The entire cycle is  
automatic.  
Page Created: 05‐04‐2010  
Revised: N/A  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
OPERATION INSTRUCTIONS (CONTINUED)  
OPERATIONAL INSPECTIONS: It is recommended that operators periodically review the following  
items while the machine is operating. All of these items are important to operating the machine in an efꢀi‐  
cient manner.  
 Review wash and rinse temperatures and compare to the minimums required by the data plate.  
Low temperatures can be an indication of a faulty thermostat, a thermostat that needs adjustment  
or some other condition that needs to be addressed.  
 Verify the pan strainers are not becoming clogged. Keeping these free of soil and debris allows for  
much better ꢀlow of water through the machine and prevents any sort of redeposit issues.  
 Water pressure. The dish‐machine is designed to run at a minimum of 15 PSIG; any lower than that  
and you won’t have enough rinse water to properly remove detergent from your ware.  
 Wash and rinse arm nozzles should be free of debris. Open nozzles are essential to the operation of  
the dish‐machine.  
SHUTDOWN: To shut the unit down, press the Start Switch on the front of the machine. To drain the  
machine, open the front door and pull up on the drain release inside the unit. If you have a steam booster for  
heating the dish‐machine, shut it down in accordance with its manufacturer’s instructions.  
CLEANING: It is recommended the unit be cleaned at least once every 24 hours or at the end of the day.  
Cleaning assists in maintained the efꢀicient operation of the unit by removing soil and debris that might oth‐  
erwise become trapped in nozzles or get deposited onto ware.  
 Curtains: should be removed and scrubbed with mild detergent/soap and a brush and allowed to  
air dry.  
 Strainers: should be removed and have debris scooped out. Never hit strainers to remove debris;  
this can cause them to warp and not seat correctly. Rinse under water should remove the rest of any  
debris trapped in the part.  
 Wash Arms: the wash arms can be removed using a 7/16” driver; however, the dish‐machine is de‐  
signed so the wash arms are self‐cleaning. Operators have the ability to ꢀlush the arms by removing  
the plastic end caps and running a rack through the unit. This should only be done as a cleaning  
function with an empty rack and a tub that is ꢀilled with water.  
 Internal Chamber: Mild detergent/soap and a dishrag should be all that is needed to clean the inside  
of the machine. Strainers and the pawl bar should be removed to provide as much room as possible.  
 External Areas: The outside of the unit should be cleaned with a standard countertop or general  
cleaner. Never attempt to clean inside any compartments, boxes or chambers that are secured with  
a cover. These normally contain live electrical components.  
 DO NOT CLEAN THE UNIT WITH ANY TYPE OF METALLIC SCRUBBING SPONGE!  
Page Created: 05‐04‐2010  
Revised: N/A  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
DELIME INSTRUCTIONS  
To proceed with the delime operation, ꢀill the dish‐machine and the correct amount of delime solution  
as recommended by the manufacturer of the chemicals. The tank capacities of the machine can be found on  
the speciꢀications page of this manual.  
After the chemicals are added, perform the following steps:  
1. Flip the NORMAL/DELIME Switch to DELIME.  
2. Disconnect or turn off chemical feeder pumps.  
3. Close all doors.  
4. Press the Start Switch and run the machine for the length of time required by the chemical solution  
manufacturer.  
5. Press the Start Switch to shut the unit off.  
6. Open the door and step away for 5 minutes.  
7. Inspect the inside of the unit to determine if your expectations have been met. If not, you may need  
to run the delime solution through the unit for more time.  
8. Once clean, drain the machine completely.  
9. Close the door.  
10. Reꢀill the unit.  
11. Press the Start Switch and run the unit in Manual for 10 minutes.  
12. Press the Start Switch to turn off the unit.  
13. Open the front door.  
14. Drain the unit.  
15. Flip the NORMAL/DELIME Switch to NORMAL.  
16. Your machine is ready to use.  
This equipment is not recommended for use with deionized water or other aggressive ꢀluids. Use of  
deionized water or other aggressive ꢀluids will result in corrosion and failure of materials and com‐  
ponents. Use of deionized water or other aggressive ꢀluids will void the manufacturer’s warranty.  
Page Created: 05‐04‐2010  
Revised: N/A  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
TROUBLESHOOTING  
UTILIZE THESE SCREWS  
FOR PLC REPLACEMENT  
Green LED lights are illuminated on the PLC when in operation. The  
POWER, OK & RUN lights indicate that 24VDC power is available  
to the PLC and that is functioning properly. If the RUN light is out,  
first check that the RUN toggle switch located behind the snap cover  
panel of the PLC is in the RUN position. Less likely is that the opera-  
tional program of the PLC may have been corrupted or lost. Tempo-  
rary power surges may have occurred. Secure all power to the ma-  
chine, wait for 30 seconds and restore power. Verify that the Green  
light is illuminated to the 24vdc power supply immediately to the left  
of the PLC. If the RUN light is still off, replace the PLC.  
INPUTS  
STATUS  
INDICATING  
LIGHTS  
RUN TOGGLE  
SWITCH  
Refer to the illustration below for the designation of each LED.  
PLC1 is used for the 44” Electric & Steam units. An expansion PLC  
(PLC2) is used in conjunction with PLC1 for 66” Electric & Steam  
units.  
OUTPUTS  
Inputs correspond to the connections behind the top flip up panel of  
the PLC and are marked I1 thru I8. Outputs correspond to the con-  
nections behind the bottom flip up panel of the PLC and are marked  
Q1 thru Q8.  
UTILIZE THESE SCREWS  
FOR PLC REPLACEMENT  
Note: All outputs are fused. Q1 & Q2 outputs for both PLC’s utilize 1.0 Amp fuses and Q3-Q8 outputs  
utilize 0.75 Amp fuses. When illuminated , the LED lights on the front of each PLC will show the input  
from and the outputs to various components as illustrated below. LED’s that may illuminate on PLC2 that  
are marked “NOT USED” have no bearing on the operation of the current ware-washers.  
PLC1  
PLC2  
LIGHT CONFIGURATION  
LIGHT CONFIGURATION  
1
5
2
6
3
7
4
8
1
5
2
6
3
7
4
8
PWR  
RUN  
OK  
INPUTS  
PWR  
RUN  
OK  
INPUTS  
1
5
2
6
3
7
4
8
1
5
2
6
3
7
4
8
OUTPUTS  
OUTPUTS  
INPUTS:  
INPUTS:  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
ON/OFF SWITCH  
DOOR SWITCH SAFETY INTERLOCKS  
RACK INLET SWITCH  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
LOWER PRE-WASH FLOAT SWITCH (66 UNITS ONLY)  
UPPER PRE-WASH FLOAT SWITCH (66 UNITS ONLY)  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
FINAL RINSE SWITCH  
LOWER WASH FLOAT SWITCH  
UPPER WASH FLOAT SWITCH  
MANUAL / DELIME SWITCH  
N/A  
OUTPUTS:  
OUTPUTS:  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
RINSE SOLENOID / RINSE SIGNAL RELAY  
WASH TANK FILL SOLENOID  
DRIVE MOTOR CONTACTOR  
WASH MOTOR CONTACTOR  
WASH HEATER CONTACTOR or STEAM HEAT RELAY  
VENTILATION FAN RELAY  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
PRE-WASH TANK FILL SOLENOID (66 UNITS ONLY)  
PRE-WASH MOTOR CONTACTOR (66 UNITS ONLY)  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
SIDE-LOADER SWITCH (ON WITH NO RACK PRESENT)  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: CONTROL BOX COMPONENTS  
All operational relays utilize green LED indicating  
lights to verify proper operation. These relays are  
mounted immediately to the right of the motor  
contactors. Please refer to the illustration to the  
right.  
R3  
R1  
R2  
R4  
R5  
LED  
THE ILLUSTRATION BELOW DEPICTS THE COMPONENTS OF A 66” ELECTRICALLY  
HEATED UNIT WITH THE BOOSTER HEATER OPTION. COMPONENT QUANTITIES AND  
PART NUMBERS MAY VARY FOR DIFFERENT UNITS. PLEASE REFER TO THR NOTES  
WITHIN THE PARTS LIST ON THE NEXT PAGE TO VERIFY THAT THE REQUIRED PART  
NUMBER IS CORRECT.  
TB1  
10  
10  
10  
10  
TB2  
10  
12  
11  
8
C3  
C2  
C1  
PLC2  
9
PLC1  
T2  
T1  
HC1  
1
R6  
R5  
R4  
R2  
R1  
3MOL  
2MOL  
1MOL  
R3  
7
6
TB4  
5
TB3  
4
3
3
2
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: CONTROL BOX COMPONENTS (CONTINUED)  
Item  
QTY Description  
Part Number  
PLC1  
1
PLC, 24VDC (IC200UDD104)  
(PROGRAMED FOR 44” UNITS)  
(PROGRAMED FOR 66” UNITS)  
05945‐003‐92‐50  
05945‐003‐92‐51  
PLC2  
T1  
1
1
PLC, 24VDC (IC200UEX014)  
(66” UNITS ONLY)  
05945‐003‐82‐47  
TRANSFORMER 208 TO 120VAC  
TRANSFORMER 230/460 TO 120VAC  
(208 VOLT UNITS)  
05950‐011‐75‐59  
05950‐011‐68‐35  
T2  
1
1
POWER SUPPLY 24VDC  
05950‐003‐76‐32  
HC1  
CONTACTOR, 24VDC 3 POLE  
CONTACTOR, 24VDC 4 POLE  
(USED ON 3-PHASE UNITS)  
(USED ON 1-PHASE UNITS)  
05945‐003‐75‐02  
05945‐003‐73‐22  
C1  
C2  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CONTACTOR, DRIVE MOTOR  
CONTACTOR, WASH PUMP  
CONTACTOR, PRE‐WASH MOTOR  
RELAY, VENT FAN  
05945‐003‐75‐22  
05945‐003‐75‐22  
05945‐003‐75‐22  
05945‐003‐76‐34  
05945‐003‐76‐34  
05945‐003‐79‐57  
05945‐003‐76‐34  
05945‐003‐76‐34  
05945‐003‐76‐34  
SEE OVERLOAD PAGE  
SEE OVERLOAD PAGE  
SEE OVERLOAD PAGE  
05940‐003‐77‐43  
05940‐003‐77‐65  
05940‐021‐94‐85  
C3  
(66” UNITS ONLY)  
R1  
R2  
RELAY, RINSE SIGNAL  
R3  
RELAY, TEMPERATURE BOARD  
RELAY, BOOSTER HEATER  
RELAY, WASH TANK STEAM  
RELAY, PHOTO CELL TABLE LIMIT  
OVERLOAD, DRIVE MOTOR  
OVERLOAD, WASH MOTOR  
R4  
(OPTIONAL)  
(STEAM UNITS ONLY)  
(OPTIONAL)  
R5  
R6  
1MOL  
2MOL  
3MOL  
TB1  
TB2  
TB3  
(USED ON 3-PHASE UNITS)  
(USED ON 3-PHASE UNITS)  
OVERLOAD, PRE‐WASH MOTOR (USED ON 3-PHASE 66” UNITS)  
TERMINAL BOARD, SIGNAL  
TERMINAL BOARD, DC  
TERMINAL BOARD, L1  
TB4  
1
1
1
1
TERMINAL BOARD, L2  
TERMINAL BLOCK 3 POLE  
FAN, 24 VDC  
05940‐021‐94‐85  
05940‐011‐48‐27  
05999‐002‐47‐12  
2
3
4
5
6
7
8
9
2
1
1
1
1
1
1
FAN FINGER GUARD  
GROUND LUG  
05999‐003‐12‐92  
05940‐200‐76‐00  
05700‐002‐42‐03  
05920‐401‐03‐14  
05920‐002‐42‐13  
05920‐011‐72‐89  
BRACKET, FUSE STRIP  
FUSE HOLDER  
FUSE HOLDER, 6 SLOT  
HOLDER, BUSSMAN FUSE  
FUSE, 1.0 AMP  
FUSE, 0.5 AMP  
(208 & 230 VOLT UNITS)  
(460 VOLT UNITS)  
05920‐002‐67‐23  
05920‐011‐72‐88  
10  
11  
12  
5
1
1
RELAY SOCKET, 20A 300V  
RELAY SOCKET, 16A 300V  
(USED FOR R1,R2, R4,R5 & R6)  
(USED FOR R3)  
05945‐003‐76‐33  
05945‐003‐79‐58  
CONTROL BOX WELDMENT  
CONTROL BOX WELDMENT  
(44” UNITS)  
(66” UNITS)  
05700‐003‐82‐04  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
PARTS SECTION: OVERLOADS  
WASH MOTORS:  
Overloads are speciꢀied for 3 phase units only.  
For GE brand, MT03* series overloads, the process for setting is as follows:  
 Determine the Full Load Amps for the wash motor  
 Set the overload at the closest setting without going over for the FLA of the motor.  
 The overload already compensates for the FLA and will have a set point that is 125% of the FLA.  
Example: Wash Motor is rated at 10.0 FLA on the data plate. The replacement MT03* overload would be set  
at 10.0. It would actually trip at 12.5 Amps.  
Wash Motor Voltage  
Part Number  
05945-003-76-29  
05945-003-76-29  
05945-003-76-27  
GE Part Number  
MT03N  
Blue Selector switch should be set  
to H for manual reset.  
208  
230  
460  
MT03N  
MT03L  
DRIVE MOTORS:  
Overloads are speciꢀied for 3 phase units only.  
For GE brand, MT03* series overloads, the process for setting is as follows:  
 Determine the Full Load Amps for the drive motor.  
 Set the overload at the closest setting without going over for the FLA of the motor.  
 The overload already compensates for the FLA and will have a set point that is 125% of the FLA.  
Example: Drive Motor is rated at 1.0 FLA on the data plate. The replacement MT03* overload would be set at  
1.0. It would actually trip at 1.25 Amps.  
Drive Motor Voltage  
Part Number  
05945-003-76-23  
05945-003-76-23  
05945-003-76-21  
GE Part Number  
MT03F  
208  
230  
460  
Blue Selector switch should be set  
to H for manual reset.  
MT03F  
MT03D  
PRE‐WASH MOTORS:  
Overloads are speciꢀied for 3 phase units only.  
For GE brand, MT03* series overloads, the process for setting is as follows:  
 Determine the Full Load Amps for the drive motor.  
 Set the overload at the closest setting without going over for the FLA of the motor.  
 The overload already compensates for the FLA and will have a set point that is 125% of the FLA.  
Example: Drive Motor is rated at 6.0 FLA on the data plate. The replacement MT03* overload would be set at  
6.0. It would actually trip at 7.5 Amps.  
Pre-Wash Motor  
Voltage  
Part Number  
GE Part Number  
Blue Selector switch should be set  
to H for manual reset.  
208  
230  
460  
05945-003-76-28  
05945-003-76-28  
05945-003-76-26  
MT03M  
MT03M  
MT03K  
NOTE: Connections should be tightened to 7 in‐lbs.  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: MISCELLANEOUS ELECTRICAL COMPONENTS  
Description  
FITTING, 1”, 90 DEGREE HUB (2 per 44” units, 1 per 66” units)  
Part Number  
05975‐003‐77‐44  
05975‐003‐88‐01  
05975‐003‐77‐46  
05975‐003‐77‐45  
05975‐003‐35‐32  
05975‐003‐33‐27  
05975‐011‐49‐03  
05975‐003‐77‐88  
05975‐003‐77‐89  
05975‐003‐77‐39  
05975‐011‐47‐81  
05975‐002‐29‐94  
05340‐011‐46‐79  
05975‐011‐59‐49  
05975‐003‐10‐46  
05975‐111‐58‐01  
05975‐200‐40‐00  
FITTING, 1” STRAIGHT HUB (1 per 66” units)  
FITTING, 3/4” STR QT 8495 SNAP  
FITTING, 3/4” 90 DEGREE QT 8510 SNAP  
FITTING, 1/2” NPT 90 DEGREE 8507  
FITTING, 1/2” NPT STR 8490  
FITTING, ,231 X .394, LIQUIDTITE  
CLAMP, 1” FLEX2 CONDUIT 1031  
CLAMP, 3/4” FLEX2 CONDUIT 1029  
PLUG, 2.5” HOLE, LOUVERED 2596  
PLUG, HEYCO 2700 G‐875  
PLUG, HEYCO, 2723  
PLUG, HEYCO, 2683  
PLUG, HEYCO, 2790  
BUSHING, HEYCO, 2236  
GROMMET, 1.250 OD X 1.000 ID  
GROMMET, 7/8 SPLIT, HEYCO, 2119  
TEMPERATURE RTD  
P/N: 06680‐002‐16‐80  
PROXIMITY SWITCH 24VDC  
P/N: 05930‐003‐76‐51  
THERMOSTAT  
P/N: 05930‐510‐02‐79  
DELIME SWITCH  
P/N: 05930‐301‐46‐00  
START SWITCH  
FLOAT SWITCH  
P/N: 05930‐003‐76‐52  
P/N: 06680‐003‐62‐65  
Page Created: 05‐04‐2010  
Revised: N/A  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: WASH HEATER & HEATER SHROUD ASSEMBLIES  
9
2
3
7
1
5
9
12  
8
6
11  
4
10  
Item QTY  
Description  
Part Number  
1
2
1
1
1
1
1
1
1
2
9
6
6
1
HEATER SHROUD WELDMENT LOWER  
HEATER SHROUD WELDMENT UPPER  
GASKET, SUCTION CASTING  
GASKET, PUMP SUCTUON  
05700‐003‐74‐21  
05700‐003‐74‐24  
05330‐003‐75‐89  
05330‐003‐75‐87  
05330‐200‐02‐70  
05700‐003‐74‐72  
05700‐003‐77‐63  
05311‐174‐01‐00  
05310‐374‐01‐00  
05310‐275‐01‐00  
05310‐275‐01‐00  
SEE HEATER CHART  
3
4
5
GASKET, HEATER  
6
HEATER BOX RAILS  
7
WASH PUMP SUCTION WELDMENT  
WASHER, S/S (NOT SHOWN)  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
NUT, HEX 5/16‐18 S/S  
8
9
10  
11  
12  
LOCKWASHER, 5/16” SPLIT S/S  
WASH HEATING ELEMENT (15kW / 18kW )  
Page Created: 05‐04‐2010  
Revised: N/A  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PUMP SUCTION ASSEMBLY  
1
USED ON PRE-WASH TANKS  
AND ALL STEAM HEATED TANKS  
4
3
2
Item QTY  
Description  
Part Number  
1
2
3
4
1
1
1
1
GASKET, SUCTION CASTING  
GASKET, PUMP SUCTUON  
PRE‐WASH PUMP SUCTION WELDMENT  
STRAINER, PRE‐WASH PUMP  
05330‐003‐75‐89  
05330‐003‐75‐87  
05700‐003‐82‐27  
05700‐003‐81‐28  
Page Created: 02‐25‐2011  
Revised: N/A  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: WASH HEATERS  
VOLTAGE PHASE KW  
PART NUMBER  
04540‐121‐68‐45  
04540‐121‐68‐46  
04540‐121‐68‐45  
04540‐121‐68‐46  
04540‐121‐68‐47  
CONTACTOR  
208  
230  
208  
230  
460  
1
1
3
3
3
15  
15  
15  
15  
15  
05945‐003‐73‐22  
05945‐003‐73‐22  
05945‐003‐75‐02  
05945‐003‐75‐02  
05945‐003‐75‐02  
208  
230  
208  
230  
460  
1
1
3
3
3
18  
18  
18  
18  
18  
04540‐121‐79‐30  
04540‐121‐79‐31  
04540‐121‐79‐30  
04540‐121‐79‐31  
04540‐121‐79‐32  
05945‐003‐73‐22  
05945‐003‐73‐22  
05945‐003‐75‐02  
05945‐003‐75‐02  
05945‐003‐75‐02  
SERVICE NOTES: when replacing wash heaters, it is highly recommended you also change out the  
gasket as well. Once installed, gaskets become compressed and are subject to extreme temperature  
changes. Replacing the gasket with a new one when replacing the heater may prevent future leaks.  
The nuts used to secure the heater to the casting should be torque to 16 in‐lbs. After tightening, the  
unit should be allowed to heat up and operate normally for approximately 30 minutes. Secure power  
to the machine and check the nuts once more to verify they are torque to 16 in‐lbs.  
Page Created: 05‐04‐2010  
Revised: N/A  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: DOOR ASSEMBLY (44)  
5
7
1
8
7
2
3
11  
7
7
6
10  
9
12  
4
2
Item QTY  
Description  
Part Number  
05700‐003‐72‐32  
09330‐003‐73‐94  
05700‐003‐76‐87  
09330‐003‐73‐83  
09330‐003‐73‐84  
05700‐003‐72‐51  
05310‐374‐01‐00  
05305‐011‐81‐58  
05305‐002‐19‐42  
05930‐002‐88‐42  
05700‐003‐81‐86  
05310‐373‐03‐00  
1
2
2
2
DOOR GUIDE BRACKET  
DOOR GUIDE  
3
1
DOOR WELDMENT  
4
1
END PIECE, DOOR RIGHT SIDE  
END PIECE, DOOR LEFT SIDE  
DOOR STOP AND SUPPORT WELDMENT  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
SCREW, 1/4”‐20 X 1”, 82 COUNTERSINK, PHILLIPS  
SCREW, 10‐32 X 1” PHILLIPS PAN HEAD  
MAGNET  
5
1
6
1
7
32  
10  
26  
1
8
9
10  
11  
12  
1
SPLASH SHIELD  
2
LOCKNUT, 6‐31 HEX W/NYLON INSERT  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PRE-WASH DOOR ASSEMBLY (22”)  
1
7
8
3
7
7
11  
9
4
2
10  
6
2
Item QTY  
Description  
Part Number  
05700‐003‐72‐32  
09330‐003‐73‐94  
05700‐003‐80‐32  
09330‐003‐73‐83  
09330‐003‐73‐84  
1
2
3
4
5
6
2
2
1
1
1
1
DOOR GUIDE BRACKET  
DOOR GUIDE  
DOOR WELDMENT  
END PIECE, DOOR RIGHT SIDE  
END PIECE, DOOR LEFT SIDE  
DOOR STOP AND SUPPORT WELDMENT (L‐R)  
DOOR STOP AND SUPPORT WELDMENT (R‐L)  
05700‐003‐80‐27  
05700‐003‐82‐50  
7
8
34  
10  
26  
1
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
SCREW, 1/4”‐20 X 1”, 82 COUNTERSINK, PHILLIPS  
SCREW, 10‐32 X 1” PHILLIPS PAN HEAD  
MAGNET  
05310‐374‐01‐00  
05305‐011‐81‐58  
05305‐002‐19‐42  
05930‐002‐88‐42  
05700‐003‐82‐46  
05310‐373‐03‐00  
9
10  
11  
12  
1
SPLASH SHIELD  
2
LOCKNUT, 6‐32 HEX W/NYLON INSERT (NOT SHOWN)  
Page Created: 02‐25‐2011  
Revised: N/A  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: DOOR SPRING ASSEMBLY  
8
4
7
OVERALL ASSEMBLY:  
05700-003-77-49  
1
44” Wash doors use 2 assemblies  
22” Pre-Wash doors use 1 assembly  
2
3
6
7
3
5
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
7
8
1
1
2
1
1
2
6
1
CASTING, DOOR SPRING MOUNT  
SPRING, DOOR  
09515‐003‐73‐78  
05315‐002‐67‐29  
05700‐002‐67‐28  
05700‐002‐83‐55  
05700‐003‐74‐10  
05311‐174‐01‐00  
05310‐374‐01‐00  
05315‐207‐01‐00  
SPINDLE, DOOR SPRING  
PIN, DOOR SPRING  
DOOR SPRING BRACKET WELDMENT  
WASHER, 1/4” S/S  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
PIN, COTTER, 3/32” X 3/4”  
Page Created: 05‐04‐2010  
Revised: N/A  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PLUMBING ASSEMBLY, MAIN WATER INLET  
1
8
2
3
4
5
6
2
7
6
2
The opposite end of this hose  
connects to the Wash Tank  
Fill Assembly (See page 38)  
The opposite end of this hose connects to the Final  
Rinse Assembly (See page 44).  
For units with the Booster Heater Option, this hose  
will connect to the booster heater inlet. (See page 64)  
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
7
8
1
3
1
1
1
2
1
1
STRAINER, INLET, 1/2”  
NIPPLE, 1/2”, CLOSE, BRASS  
TEE, BRASS, 1/2” X 1/2” X 1/2”  
REGULATOR, 1/2”  
04730‐217‐01‐10  
04730‐207‐15‐00  
04730‐211‐27‐00  
04820‐100‐04‐07  
04810‐003‐75‐16  
04720‐003‐76‐09  
05700‐003‐74‐42  
05700‐003‐74‐86  
VALVE, 1/2” NPT BRASS, 24VDC COIL  
HOSE, 1/2” X 42” S/S BRAIDED W/PTFE, MALE SWIVEL  
BRACKET, INLET PLUMBING SUPPORT  
BRACKET, UPPER INLET PLUMBING SUPPORT  
Page Created: 05‐04‐2010  
Revised: N/A  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: WASH TANK FILL ASSEMBLY  
2
1
5
7
1
3
The hose from the Main Water  
Inlet Plumbing connects to this  
solenoid valve. (See page37)  
8
4
6
Item QTY  
Description  
Part Number  
1
2
2
1
ELBOW, 90 DEGREE, 1/2” STREE, BRASS  
04730‐206‐08‐00  
VACUUM BREAKER, 1/2”  
VACUUM BREAKER REPAIR KIT  
04820‐003‐06‐13  
06401‐003‐06‐23  
3
4
5
6
7
8
1
1
1
1
1
2
NIPPLE, 1/2” CLOSE, BRASS  
04730‐207‐15‐00  
05330‐003‐75‐91  
04810‐003‐75‐16  
05700‐003‐76‐81  
05700‐003‐76‐84  
05310‐374‐01‐00  
GASKET, RINSE MANIFOLD  
VALVE, 1/2” NPT BRASS, 24VDC COIL  
TUBE WELDMENT, TANK FILL  
TANK FILL INJECTOR WELDMENT  
LOCKNUT, 1/4”‐20 HEX WITH NYLON INSERT (NOT SHOWN)  
Page Created: 05‐04‐2010  
Revised: N/A  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PRE-WASH TANK FILL ASSEMBLIES  
12  
6
3
5
5
10  
3
12  
4
11  
3
2
3
7
8
9
7
11  
10  
7
7
STANDARD PRE-WASH  
FILL PLUMBING  
1
PRE-WASH FILL PLUMBING WITH  
OPTIONAL COLD WATER FILL  
Item  
QTY (*)  
Description  
Part Number  
1
2
3
4
5
6
1
1
TUBE WELDMENT, TANK FILL  
05700‐003‐76‐81  
05330‐003‐75‐91  
05310‐374‐01‐00  
05700‐003‐76‐84  
04730‐206‐08‐00  
GASKET, RINSE MANIFOLD  
4 (6)  
1
LOCKNUT, 1/4”‐20 HEX WITH NYLON INSERT (NOT SHOWN)  
TANK FILL INJECTOR WELDMENT  
2
ELBOW, 90 DEGREE, 1/2” STREET, BRASS  
1
VACUUM BREAKER, 1/2”  
VACUUM BREAKER REPAIR KIT  
04820‐003‐06‐13  
06401-003-06-23  
7
8
2 (3)  
1
NIPPLE, 1/2” CLOSE, BRASS  
04730‐207‐15‐00  
04730‐211‐27‐00  
04730‐209‐03‐00  
04810‐003‐75‐16  
04720‐003‐76‐09  
05700‐003‐81‐98  
TEE, 1/2 x 1/2 x 1/2 NPT BRASS  
9
1 (0)  
1 (2)  
1 (2)  
1 (2)  
PLUG, 1/2 NPT BRASS (REMOVED FOR COLD WATER FILL OPTION)  
VALVE, 1/2” NPT BRASS, 24VDC COIL  
10  
11  
12  
HOSE, 1/2” X 42” S/S BRAIDED W/PTFE, MALE SWIVEL  
WATER INLET FITTING  
* NUMBERS IN PARENTHESIS DENOTE CHANGED QUANTITIES WHEN THE COLD WATER PRE-WASH FILL OPTION IS ADDED.  
Page Created: 02‐25‐2011  
Revised: N/A  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: WASH MANIFOLD AND ARM ASSEMBLY  
14  
9
10  
12  
14  
8
11  
13  
11  
7
10  
14  
13  
3
6
4
5
4
2
Mechanical Pump Seal  
05330-002-34-22  
1
Page Created: 05‐04‐2010  
Revised: N/A  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: WASH MANIFOLD AND ARM ASSEMBLY (CONTINUED)  
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
1
1
1
2
1
1
PUMP & MOTOR ASSEMBLY  
GASKET, PUMP SUCTION  
SEE TABLE BELOW  
05330‐003‐75‐87  
05330‐003‐75‐88  
04730‐003‐15‐40  
05700‐003‐77‐62  
GASKET, PUMP DISCHARGE  
HOSE CLAMP, RANGE 2‐9/16” TO 3‐1/2”  
HOSE, WASH PUMP DISCHARGE  
(L‐R MACHINES) LOWER MANIFOLD  
(R‐L MACHINES) LOWER MANIFOLD  
05700‐003‐74‐29  
05700‐003‐74‐28  
7
1
1
CASTING, WASH MANIFOLD  
09515‐003‐71‐50  
05700‐003‐72‐37  
05700‐003‐73‐66  
05700‐003‐75‐80  
05700‐003‐75‐79  
04730‐603‐12‐00  
05330‐003‐73‐71  
05330‐003‐73‐72  
8
TUBE, MANIFOLD RISER  
9
1
WASH MANIFOLD WELDMENT, UPPER  
WASH ARM WELDMENT, RIGHT  
WASH ARM WELDMENT, LEFT  
CAP, THREADED  
10  
11  
12  
13  
14  
2
2
12  
3
O‐RING, SILICONE, .103 DIA., 2‐1/2” X 2‐11/16” OD  
O‐RING, SILICONE, .139 DIA., 2‐1/4” ID X 2‐1/2” OD  
4
PUMP & MOTOR ASSEMBLY  
Part Number  
WASH PUMP, 3HP 208V 60HZ 3‐PHASE  
WASH PUMP, 3HP 230V 60HZ 3‐PHASE  
WASH PUMP, 3HP 460V 60HZ 3‐PHASE  
WASH PUMP, 3HP 208V 60HZ 1‐PHASE  
WASH PUMP, 3HP 230V 60HZ 1‐PHASE  
06105‐003‐76‐11  
06105‐003‐76‐11  
06105‐003‐76‐11  
06105‐003‐76‐13  
06105‐003‐76‐13  
Page Created: 05‐04‐2010  
Revised: N/A  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PRE-WASH MANIFOLD AND ARM ASSEMBLIES  
9
12  
13  
8
16  
12  
9
14  
11  
ILLUSTRATES PARTS  
FOR A LEFT TO RIGHT  
PRE-WASH  
8
11  
8
16  
8
10  
9
15  
ILLUSTRATES PARTS  
FOR A RIGHT TO LEFT  
PRE-WASH  
16  
2
6
9
15  
4
5
10  
8
4
3
16  
7
2
4
5
4
1
3
2
Mechanical Pump Seal  
05330-002-34-22  
1
Page Created: 02‐25‐2011  
Revised: N/A  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PRE-WASH MANIFOLD AND ARM ASSEMBLY (CONTINUED)  
Item QTY  
Description  
Part Number  
1
2
1
1
1
2
1
1
1
3
2
1
1
1
1
1
1
4
PUMP & MOTOR ASSEMBLY  
SEE TABLE BELOW  
05330‐003‐75‐87  
05330‐003‐75‐88  
04730‐003‐15‐40  
05700‐003‐77‐62  
05700‐003‐81‐54  
05700‐003‐81‐79  
05330‐003‐73‐71  
05330‐003‐73‐72  
09515‐003‐77‐22  
05700‐003‐81‐53  
05700‐003‐81‐76  
05700‐003‐75‐79  
05700‐003‐75‐80  
05700‐003‐80‐96  
04730‐603‐12‐00  
GASKET, PUMP SUCTION  
3
GASKET, PUMP DISCHARGE  
4
HOSE CLAMP, RANGE 2‐9/16” TO 3‐1/2”  
HOSE, WASH PUMP DISCHARGE  
LOWER MANIFOLD (L‐R UNITS)  
LOWER MANIFOLD (R‐L UNITS)  
O‐RING, SILICONE, .103 DIA., 2‐1/2” X 2‐11/16” OD  
O‐RING, SILICONE, .139 DIA., 2‐1/4” ID X 2‐1/2” OD  
CASTING, PRE‐WASH MANIFOLD  
TUBE, MANIFOLD RISER  
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
PRE‐WASH MANIFOLD WELDMENT, UPPER  
WASH ARM WELDMENT, LEFT  
WASH ARM WELDMENT, RIGHT  
PRE‐WASH ARM WELDMENT, LOWER  
CAP, THREADED  
PUMP & MOTOR ASSEMBLY  
Part Number  
PRE‐WASH PUMP, 2HP 208V 60HZ 3‐PHASE  
PRE‐WASH PUMP, 2HP 230V 60HZ 3‐PHASE  
PRE‐WASH PUMP, 2HP 460V 60HZ 3‐PHASE  
PRE‐WASH PUMP, 2HP 208V 60HZ 1‐PHASE  
PRE‐WASH PUMP, 2HP 230V 60HZ 1‐PHASE  
06105‐003‐76‐12  
06105‐003‐76‐12  
06105‐003‐76‐12  
06105‐003‐76‐14  
06105‐003‐76‐14  
Mechanical Pump Seal  
05330-002-34-22  
Page Created: 02‐25‐2011  
Revised: N/A  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: RINSE ASSEMBLY  
21  
22  
1
1
2
7
17  
16  
20  
8
6
9
14  
1
12  
24  
10  
11  
17  
15  
(Note 2)  
(Note 1)  
RINSE INJECTOR  
CONNECTIONS  
P: PRESSURE SWITCH  
S: SANITIZER  
R: RINSE AID  
3
19  
18  
23  
5
Note 1:  
This hose connects to part  
#16 at one end and to part  
#20 at the opposite end.  
15  
4
Note 2:  
A hose from the Main  
Water Inlet Assembly  
connects to this elbow.  
(See page 37)  
19  
18  
17  
23  
For units with the  
Booster Heater Option,  
the hose will connect to  
the booster heater outlet.  
(See page 64)  
Page Created: 05‐04‐2010  
Revised: N/A  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: RINSE ASSEMBLY (CONTINUED)  
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
3
1
1
1
1
1
ELBOW, 90 DEGREE 1/2 STREET BRASS  
VACUUM BREAKER 1/2"  
UPPER RINSE ARM  
04730‐206‐08‐00  
04820‐003‐06‐13  
05700‐003‐76‐02  
05700‐003‐76‐04  
05700‐003‐76‐79  
LOWER RINSE ARM  
RINSE MANIFOLD  
RINSE INJECTOR (L‐R UNITS)  
RINSE INJECTOR (R‐L UNITS)  
05700‐003‐76‐82  
05700‐003‐76‐83  
7
1
1
1
2
1
1
1
3
1
6
2
2
1
1
1
2
1
NIPPLE‐ 1/2 CLOSE BRASS  
04730‐207‐15‐00  
04810‐011‐72‐67  
04730‐002‐22‐56  
04730‐209‐07‐37  
05330‐003‐75‐91  
05310‐924‐02‐05  
04730‐209‐01‐00  
05330‐003‐77‐82  
04730‐003‐77‐83  
05310‐374‐01‐00  
05305‐274‐02‐00  
05311‐274‐01‐00  
05700‐003‐77‐12  
06685‐111‐88‐34  
09905‐002‐97‐74  
05700‐011‐35‐92  
04720‐003‐76‐10  
8
VALVE, BALL TEST COCK 1/4" BRONZE  
TEE, 1/2 FNPT X 1/2 FNPT 1/4 FNPT  
PLUG, 1/8 N.P.T. BRASS  
9
10  
11  
12  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
GASKET, RINSE MANIFOLD  
FITTING, IMPERIAL BRASS  
PLUG, 1/4 211P‐4  
O‐RING, SILICON .103 DIA.,11/16 X 7/8 OD  
ELBOW, BRASS 90 DEGREE 1/4 NPTM x 1/4 NPTF  
LOCKNUT, 1/4‐20 HEX W/NYLON INSERT  
BOLT, 1/4‐20 X 1/2 LONG  
LOCKWASHER, SPRING 1/4  
ELBOW WELDMENT, TEMP GAUGE  
GAUGE, 0‐100# PRESSURE  
DECAL 15‐25 PSI  
END PLUG  
HOSE, 1/4x30" SS BRAIDED W/PTFE, MALE SWIVEL  
Page Created: 05‐04‐2010  
Revised: N/A  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PAWL BAR ASSEMBLIES  
TYPICAL PAWL DOG  
WITH HARDWARE  
6
3
4
3
5
PAWL BAR WELDMENT  
FOR ALL 66" UNITS  
2
PAWL BAR WELDMENT AND PAWL DOGS  
ARRANGED FOR ALL 66" UNITS  
PAWL BAR WELDMENT  
FOR ALL 44" UNITS  
1
PAWL BAR WELDMENT AND PAWL DOGS  
ARRANGED FOR ALL 44" UNITS  
Item QTY  
Description  
Part Number  
05700‐031‐72‐77  
05700‐003‐89‐34  
05700‐011‐71‐45  
1
2
1
1
PAWL BAR WELDMENT (44” Units)  
PAWL BAR WELDMENT (66” Units)  
SPACER, PAWL BAR DOG  
3
4
5
6
24 (44” Units)  
36 (66” Units)  
12 (44” Units)  
18 (66” Units)  
PAWL BAR DOG CASTING  
09515‐021‐69‐00  
05310‐011‐72‐55  
05306‐011‐36‐94  
12 (44” Units)  
18 (66” Units)  
LOCKNUT, 3/8”‐16 W/NYLON INSERT  
BOLT, 3/8”‐16 X 1‐3/4” LONG  
12 (44” Units)  
18 (66” Units)  
Page Created: 05‐04‐2010  
Revised: 06‐27‐2011  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PAWL BAR BRACKET ASSEMBLY  
4
3
5
3
2
5
6
1
2
The PAWL BAR ROLLER REPLACEMENT KIT  
comes with items 2, 3, 5 and 6.  
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
1
2
8
6
2
2
PAWL BAR BRACKET WELDMENT  
SCREW, 1/4”‐20 X 1‐3/4” HEX HEAD  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
WASHER, S/S  
05700‐003‐74‐39  
05305‐274‐10‐00  
05310‐374‐01‐00  
05311‐174‐01‐00  
05700‐011‐68‐16  
05700‐011‐68‐14  
06401‐003‐11‐80  
ROLLER, BRACKET ROD  
SHAFT, ROLLER, 3/8” X 1.13”  
PAWL BAR ROLLER REPLACEMENT KIT  
Page Created: 05‐04‐2010  
Revised: N/A  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: PAWL BAR GUTTER ASSEMBLY  
1
2
DRIVE ROD HOLE COVER  
P/N: 05700‐003‐75‐68  
3
PAWL BAR DRIVE LINKAGE  
P/N: 09515‐021‐87‐73  
Item QTY  
Description  
Part Number  
1
2
3
4
1
1
1
1
1
1
TOP GUIDE BLOCK  
05700‐011‐69‐49  
05700‐011‐69‐50  
05700‐021‐66‐86  
05330‐011‐68‐55  
06401‐003‐09‐95  
06401‐003‐10‐15  
BOTTOM GUIDE BLOCK  
PAWL BAR GUTTER WELDMENT  
DRIVE GUTTER GASKET (NOT SHOWN)  
GUTTER WELDMENT REPLACEMENT KIT (W/HARDWARE)  
GUIDE BLOCK REPLACEMENT KIT  
Page Created: 05‐04‐2010  
Revised: N/A  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: RACK PADDLE ASSEMBLY  
4
2
5
3
1
8
6
7
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
7
8
1
1
2
2
1
1
1
1
1
RACK PADDLE WELDMENT  
BUMPER, RACK PADDLE  
05700‐003‐76‐71  
09330‐003‐74‐82  
05305‐274‐05‐00  
05310‐374‐02‐00  
05310‐374‐01‐00  
05305‐003‐31‐63  
05930‐003‐31‐63  
05700‐011‐60‐92  
05700‐003‐76‐74  
SCREW, 1/4”‐20 X 7/8” SS HH  
LOCKNUT, 1/4”‐20 LOW PROFILE W/NYLON INSERT  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
SCREW, 1/4”‐20 X 2‐3/4” HEX HEAD  
MAGNET  
WASH/RINSE END CAP  
ENTIRE ASSEMBLY  
Page Created: 05‐04‐2010  
Revised: N/A  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: RINSE PADDLE ASSEMBLIES  
1
RINSE PADDLE ASSEMBLY  
FOR LEFT TO RIGHT UNITS  
4
RINSE PADDLE WELDMENT  
FOR RIGHT TO LEFT UNITS  
(ALL OTHER PARTS ARE THE SAME  
REGARDLESS OF DIRECTION)  
1
5
8
2
3
7
6
Item QTY  
Description  
Part Number  
1
1
RINSE PADDLE WELDMENT (L‐R)  
RINSE PADDLE WELDMENT (R‐L)  
05700‐003‐81‐91  
05700‐003‐81‐96  
2
3
4
5
6
7
8
1
2
2
4
4
1
1
1
STUD, 1/4”‐20 X 8.50” LONG, S/S, DOUBLE ENDED THREAD  
LOCKNUT, 1/4”‐20 HEX W/NYLON INSERT  
LOCKNUT, 1/4”‐20 LOW PROFILE W/NYLON INSERT  
SCREW, 1/4‐20 x 7/8” HEX HEAD S/S  
MAGNET  
05306‐003‐76‐31  
05310‐374‐01‐00  
05310‐374‐02‐00  
05305‐274‐05‐00  
05930‐003‐31‐63  
05700‐011‐60‐92  
09330‐003‐81‐04  
END CAP  
BUMPER, RINSE PADDLE  
ENTIRE ASSEMBLY (L‐R)  
ENTIRE ASSEMBLY (R‐L)  
05700‐003‐81‐92  
05700‐003‐81‐95  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: DRAIN ASSEMBLY PARTS  
6
6
6
6
THIS CONFIGURATION IS  
USED FOR THE 44” UNIT  
WASH TANK & THE 66” UNIT  
PRE-WASH TANK AND IS THE  
OVERFLOW TO THE DRAIN  
3
3
1
1
THIS CONFIGURATION IS USED  
FOR THE 66” UNIT WASH TANK  
AND ACTS AS A STOPPER  
2
4
5
5
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
1
1
2
2
1
2
DRAIN HANDLE  
05700‐003‐83‐66  
05700‐003‐75‐55  
05700‐003‐83‐67  
05700‐003‐82‐76  
05330‐400‐05‐00  
05310‐374‐01‐00  
DRAIN STANDPIPE (OVERFLOW)  
DRAIN HANDLE BRACKET  
DRAIN STANDPIPE  
O‐RING, VITON  
LOCKNUT, 1/4‐20 HEX W/NYLON INSERT  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: COVERS, GUARDS AND PANELS  
TOP PANEL ASSEMBLY  
05700‐003‐78‐06  
(44” & 66” UNITS)  
1
2
PRE‐WASH TOP PANEL ASSEMBLY  
HANDLE  
W/HANDLE: 05700‐003‐82‐49  
05700‐002‐67‐21  
LEFT SIDE PANEL  
05700‐003‐73‐82  
(Electric Units & Steam L‐R)  
05700‐003‐83‐87  
(Steam R‐L )  
COVER, WASH HEATER  
05700‐003‐74‐73  
(ELECTRICALLY HEATED  
UNITS ONLY)  
RIGHT SIDE PANEL  
05700‐003‐73‐81  
CONTROL DRESS PANEL  
05700‐003‐78‐15  
(Electric Units & Steam R‐L)  
05700‐003‐83‐71  
(Steam L‐R Units)  
LOWER DRESS PANEL  
05700‐003‐72‐81 (44” UNITS)  
05700‐003‐80‐42 (66” UNITS)  
DRIVE MOTOR GUARD  
05700-003-79-45  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: BRACKETS  
START SWITCH BRACKET  
05700‐003‐74‐65  
LIMIT SWITCH BRACKET  
05700‐021‐71‐18  
FILL TUBE BRACKET  
05700‐003‐79‐55  
UPPER DRIVE  
SUPPORT BRACKET  
05700‐003‐77‐18  
LOWER DRIVE  
SUPPORT BRACKET  
05700‐003‐77‐19  
CONDUIT BRACKET  
05700‐003‐77‐87  
PANEL BRACKET, LEFT  
05700‐003‐78‐13  
PANEL BRACKET, RIGHT  
05700‐003‐78‐14  
FLOAT & STANDPIPE  
BRACKET ASSEMBLY  
05700‐003‐81‐87  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: MISCELLANEOUS PARTS  
REAR RACK RAIL  
05700‐003‐77‐54 (44” UNITS)  
05700‐003‐80‐57 (66” UNITS)  
FRONT RACK RAIL  
05700‐003‐79‐09 (44” L‐R)  
05700‐003‐79‐09 (44” R‐L)  
05700‐003‐81‐93 (66” L‐R)  
05700‐003‐81‐89 (66” R‐L)  
CURTAIN BRACKET, END  
05700‐003‐77‐60  
CURTAIN BRACKET, MIDDLE  
05700‐003‐77‐61  
STRAINER, WASH TANK  
05700‐003‐74‐31  
DOOR LATCH ASSEMBLY  
05700‐003‐75‐76  
STRAINER, PRE‐WASH TANK  
05700‐003‐80‐75  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: VENTILATION COWL PARTS  
3
2
5
1
4
Item QTY Description  
Part Number  
1
2
1
1
VENTILATION COWL  
VENTILATION COWL, LEFT SIDE ( FOR DOOR ACCENT PANEL OPTION)  
VENTILATION COWL, RIGHT SIDE ( FOR DOOR ACCENT PANEL OPTION) 05700‐003‐75‐78  
05700‐003‐77‐50  
05700‐003‐75‐77  
2
3
4
5
2
2
2
4
VENTILATION SCOOP  
05700‐003‐75‐74  
05700‐003‐75‐73  
05700‐003‐74‐76  
05700‐003‐17‐98  
VENTILATION DUCT ADAPTER  
DAMPER, VENTILATION SCOOP  
CURTAIN HOOK  
Page Created: 05‐04‐2010  
Revised: N/A  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: VENTILATION COWL FOR UNHOODED SIDE-LOADER OPTION  
STEP 1  
TO ATTACH THE CURTAIN AND ROD TO VENTILA-  
TION COWL ENSURE THE CURTAIN IS ORIENTED  
AS DEPICTED AND FOLLOW THE STEPS BELOW.  
STEP 3  
1A  
8
STEP 1: INSERT THE ROD INTO THE HOLE AT THE REAR OF  
THE VENTILAION COWL  
DEPICTS VENTILATION  
COWL FOR LEFT UN-  
5
HOODED SIDE-LOADER  
7
STEP 2: INSERT THE ROD INTO THE BRACKET AT THE  
FRONT OF THE VENTILATION COWL  
STEP 3: GENTLY LIFT THE ROD AT THE CURTAIN CUTOUT  
OVER AND ONTO THE CURTAIN HOOK ENSURING THAT THE  
ENDS OF THE ROD STAY INSERTED IN THE HOLES.  
STEP 2  
DEPICTS VENTILATION COWL FOR  
RIGHT UNHOODED SIDE-LOADER  
1B  
9
8
10  
5
7
ORIENT THE CURTAIN SO THAT  
THE 3 CUTOUTS ARE LOCATED  
AT THE BEND OF THE ROD.  
7
6
9
10  
Item QTY Description  
Part Number  
1A  
1B  
1
1
VENTILATION COWL w/CUTOUT FOR LEFT SIDE LOADER  
VENTILATION COWL w/CUTOUT FOR RIGHT SIDE LOADER  
05700‐003‐84‐67  
05700‐003‐84‐66  
2
3
1
1
1
2
1
1
3
3
3
VENTILATION SCOOP (NOT SHOWN)  
VENTILATION DUCT ADAPTER (NOT SHOWN)  
DAMPER, VENTILATION SCOOP (NOT SHOWN)  
CURTAIN HOOK  
05700‐003‐75‐74  
05700‐003‐75‐73  
05700‐003‐74‐76  
05700‐003‐86‐10  
08415‐003‐84‐88  
05700‐003‐84‐57  
05310‐374‐01‐00  
05311‐274‐01‐00  
05305‐274‐02‐00  
4
5
6
CURTAIN, XL FOR SIDE‐LOADER  
CURTAIN ROD  
7
8
LOCKNUT, 1/4‐20 HEX w/NYLON INSERT  
LOCKWASHER, 1/4 ID SPRING  
BOLT, 1/4‐20 x 1/2“ LONG  
9
10  
Page Created: 06‐27‐2011  
Revised: N/A  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: DRIVE ASSEMBLY  
29  
29  
19  
21  
20  
6
13  
17  
22  
11  
13  
20  
16  
28  
8
5
25  
7
16  
13  
14  
23  
24  
13  
9
14  
21  
15  
27  
14  
15  
13  
3
16  
26  
1
4
11  
12  
2
11  
10  
13  
17  
Page Created: 05‐04‐2010  
Revised: N/A  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: DRIVE ASSEMBLY  
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
7
8
9
1
1
1
2
1
1
1
1
1
HUB, DRIVE  
05700‐011‐67‐97  
03120‐011‐71‐81  
06105‐011‐71‐88  
05700‐021‐67‐50  
03120‐021‐71‐87  
05700‐003‐75‐61  
05700‐021‐67‐39  
05700‐011‐67‐58  
05700‐021‐67‐42  
BEARING, ROLLER WC88013  
GEAR, 50/1 DRIVE MOTOR  
W‐COUPLING & EXPANSION LEGS WELD  
BLOCK, PILLOW  
W‐DRIVE SUPPORT WELDMENT  
F‐SOCKET, DRIVE  
F‐PLATE, SPACER  
PLATE, DRIVE ROD  
10  
11  
12  
13  
14  
1
3
SPRING, DRIVE  
05315‐011‐83‐51  
5311‐011‐71‐93  
05305‐011‐71‐94  
05311‐276‐01‐00  
05311‐176‐01‐00  
WASHER, 1/2 FLAT S/S  
BOLT, 1/2‐13 X 1 3/4  
3/8 LOCKWASHER  
WASHER 3/8" FLAT S/S  
1
12  
8
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
12  
4
4
2
4
2
3
1
1
1
1
2
2
1
4
NUT, HEX 3/8‐16 S/S  
05310‐276‐01‐00  
05306‐011‐36‐94  
05306‐011‐71‐60  
05311‐174‐01‐00  
05310‐374‐01‐00  
05305‐274‐04‐00  
05311‐274‐01‐00  
05311‐175‐01‐00  
05305‐002‐98‐39  
05700‐011‐89‐18  
05700‐003‐78‐03  
05305‐011‐86‐65  
05305‐274‐24‐00  
05307‐003‐79‐67  
05310‐274‐01‐00  
BOLT, 3/8‐16 X 1 3/4" LG  
3/8‐16 X 3/4" LONG  
WASHER, S/S 1/4‐20 I.D.  
LOCKNUT, 1/4‐20 HEX W/NYLON INSERT  
BOLT, HEX HEAD 1/4 ‐ 20 X 3/4  
LOCKWASHER, SPRING 1/4  
WASHER, 5/16 ‐ 18 S/S  
SET SCREW, 5/16‐18 X 1/4  
COLLAR, SHAFT CONVEYOR DRIVE  
W‐DRIVE LEVER WELDMENT  
SCREW, 10‐32 X .75 SHOULDER .25  
SCREW, 1/4‐20 x 5/8 S/S HEX HEAD  
STUD, 1/4‐20 x 5.75 ALL THREAD  
NUT, HEX 1/4 ‐ 20  
Page Created: 05‐04‐2010  
Revised: N/A  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: SIDE LOADERS  
17  
13  
16  
14  
2
4
5
16  
19  
16  
17  
14  
18  
4
DETAIL A  
1
3
15  
16  
A
16  
ILLUSTRATION DEPICTS A 23” RIGHT  
TO LEFT UNHOODED SIDE-LOADER.  
THE 23” LEFT TO RIGHT AS WELL AS BOTH  
DIRECTIONS OF THE 30” SIDE-LOADERS  
HAVE THE DIFFERENCES IN THE PARTS  
14  
REFLECTED IN THE PARTS LIST.  
33  
32  
26  
32  
33  
31  
*NOTE  
32  
25  
*NOTE  
26  
27  
*NOTE: Order lengths of Hose or Conduit by  
measuring the lengths in the ꢀield and add an  
additional 1 foot to ensure any custom cut  
lengths are accounted for.  
28  
29  
30  
Page Created: 06‐27‐2011  
Revised: N/A  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: SIDE LOADERS (CONTINUED)  
4
15  
16  
10  
1
B
16  
9
16  
11  
6
12  
16  
23  
6
24  
21  
22  
7
20  
24  
7
DETAIL B  
8
14  
16  
8
14  
16  
23  
ILLUSTRATION DEPICTS A 23” RIGHT  
TO LEFT UNHOODED SIDE-LOADER.  
THE 23” LEFT TO RIGHT AS WELL AS BOTH  
DIRECTIONS OF THE 30” SIDE-LOADERS  
HAVE THE DIFFERENCES IN THE PARTS  
REFLECTED IN THE PARTS LIST.  
16  
Page Created: 06‐27‐2011  
Revised: N/A  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: SIDE LOADERS (CONTINUED)  
Item QTY  
Description  
Part Number  
1
1
1
1
1
TUB WELDMENT, 23” SIDE‐LOADER L‐R  
TUB WELDMENT, 23” SIDE‐LOADER R‐L  
TUB WELDMENT, 30” SIDE‐LOADER L‐R  
TUB WELDMENT, 30” SIDE‐LOADER R‐L  
05700‐003‐84‐59  
05700‐003‐84‐58  
05700‐003‐88‐46  
05700‐003‐88‐39  
2
1
1
RACK SUPPORT L‐R  
RACK SUPPORT R‐L  
05700‐003‐90‐00  
05700‐003‐89‐95  
3
4
5
6
7
1
1
1
2
2
STRAINER  
05700‐021‐85‐10  
05700‐003‐84‐78  
06401‐003‐89‐96  
05700‐002‐56‐14  
05700‐021‐87‐59  
PAWL BAR DRIVE LINKAGE (SEE SIDE‐LOADER DRIVE LINKAGE PAGE)  
ACTUATOR SWITCH ASSEMBLY  
LEG SOCKET  
SUPPORT LEG  
8
2
1
FOOT, ADJUSTABLE  
05340‐108‐01‐03  
05700‐021‐66‐86  
05700‐011‐69‐49  
05700‐011‐69‐50  
05330‐011‐68‐55  
05700‐003‐87‐39  
05311‐174‐01‐00  
05305‐274‐02‐00  
05310‐374‐01‐00  
05700‐011‐68‐16  
05305‐274‐10‐00  
05700‐011‐68‐14  
05700‐021‐71‐18  
05940‐011‐84‐41  
05700‐003‐87‐43  
05700‐003‐87‐41  
05310‐373‐03‐00  
*04720‐011‐69‐16  
04730‐719‐06‐09  
05700‐021‐84‐61  
04730‐011‐69‐93  
04730‐207‐40‐00  
04730‐206‐32‐00  
*05975‐003‐33‐36  
04730‐002‐41‐88  
05975‐003‐33‐27  
9
GUTTER, PAWL BAR  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
1
GUIDE BLOCK TOP‐SLOTTED  
GUIDE BLOCK BOTTOM‐SLOTTED  
GASKET, DRIVE GUTTER  
1
1
1
BRACKET, LOADER PAWL BAR SUPPORT  
WASHER, 1/4” ID STAINLESS STEEL  
BOLT, 1/4‐20 x 1/2” LONG  
LOCKNUT, 1/4‐20 HEX w/NYLON INSERT  
ROLLER  
16  
4
39  
2
2
SCREW, 1/4‐20 x 1‐3/4” LONG HEX HEAD  
ROLLER SHAFT  
2
1
BRACKET, LIMIT SWITCH  
1
TERMINAL BOARD  
1
SWITCH ASSEMBLY, SIDE‐LOADER (24VDC)  
COVER, SIDE LOADER SWITCH  
LOCKNUT, 6‐32 HEX w/NYLON INSERT  
1
2
NOTE* DRAIN HOSE, POLYBRAID 1” ID (SEE NOTE)  
2
1
1
1
1
HOSE CLAMP (RANGE: 13/16” TO 1‐1/2”)  
DRAIN FITTING WELDMENT  
TEE, 1‐1/2” BRASS F‐NPT  
NIPPLE, 1‐1/2” CLOSE BRASS  
ELBOW, 90 DEG STREET, BRASS 1‐1/2” NPT  
NOTE* CONDUIT, 1/2” FLEX 2 (SEE NOTE)  
3
CLAMP, 1” NYLON  
2
FITTING, 1/2” STRAIGHT TWIST / SNAP  
*NOTE: Order lengths of Hose or Conduit by measuring the lengths in the ꢀield and add an additional 1 foot  
to ensure any custom cut lengths are accounted for.  
Page Created: 06‐27‐2011  
Revised: N/A  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: SIDE LOADER DRIVE LINKAGE  
1
6
4
5
8
3
2
7
Item QTY  
Description  
Part Number  
1
2
3
4
5
6
7
8
1
1
3
3
3
6
3
3
PAWL BAR, SIDE LOADER  
05700‐021‐86‐88  
05700‐001‐99‐16  
05700‐021‐86‐79  
05310‐011‐72‐55  
05306‐011‐36‐94  
05700‐011‐71‐45  
05305‐274‐27‐00  
05310‐374‐01‐00  
DRIVE LINKAGE, SIDE LOADER  
PAWL DOG w/WING  
LOCKNUT, 3/8‐16 w/NYLON INSERT  
BOLT, 3/8‐16 x 1‐3/4” LONG HEX HEAD  
SPACER, PAWL BAR DOG  
SCREW, 1/4‐20 x 1” LONG HEX HEAD  
LOCKNUT, 1/4‐20 HEX w/NYLON INSERT  
Page Created: 06‐27‐2011  
Revised: N/A  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: STEAM HEATING COIL ASSEMBLY  
4
2
8
3
5
8
9
10  
11  
1
12  
18  
13  
6
14  
13  
17  
16  
15  
8
8
9
10  
11  
12  
13  
7
20  
19  
Item QTY  
Description  
Part Number  
05700‐003‐83‐70  
05700‐003‐83‐33  
05700‐003‐83‐32  
05700‐003‐83‐35  
05305‐274‐22‐00  
05310‐374‐02‐00  
05700‐003‐83‐79  
05700‐001‐17‐86  
05700‐001‐17‐87  
05310‐011‐17‐85  
04730‐911‐02‐34  
04730‐912‐01‐00  
04730‐907‐01‐00  
04820‐011‐87‐39  
04730‐011‐87‐37  
04730‐217‐01‐32  
04730‐907‐02‐34  
04820‐100‐19‐00  
06680‐500‐02‐77  
04730‐002‐86‐59  
1
2
1
3
3
6
6
6
1
4
2
2
2
2
3
1
1
1
1
1
1
1
STEAM COIL WELDMENT  
STEAM COIL SPACER WELDMENT  
PLATE, STEAM COIL SPACER  
3
4
SLEEVE, 1/4” ID x 5/8”LONG  
5
BOLT, 1/4‐20 x 1‐1/4 HEX HEAD  
LOCKNUT, 1/4‐20 LOW PROFILE W/NYLON INSERT  
BRACKET, STEAM COIL ADJUSTMENT  
GASKET, STEAM COIL  
6
7
8
9
WASHER, STEAM COIL ADAPTER  
NUT, STEAM COIL ADAPTER  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
REDUCER, 3/4 NPTM x 1/2 NPTF BLACK IRON  
UNION, 3/4 NPT BLACK IRON  
NIPPLE, CLOSE 3/4 NPT BLACK IRON  
VALVE, 3/4 STEAM 110VOLT COIL  
ELBOW, 3/4 NPT STREET, BLACK IRON  
Y‐STRAINER, 3/4 NPT STEAM  
NIPPLE, 3/4 NPT x 4” LONG, BLACK IRON  
VALVE, GATE 3/4 NPT STEAM  
TRAP, STEAM 3/4 NPT  
PLUG, 3/4 NPT SQUARE HEAD, BLACK IRON  
Page Created: 02‐25‐2010  
Revised: N/A  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: BOOSTER HEATER OPTION (ELECTRIC)  
1
2
11  
This hose connects to the Main Inlet  
Plumbing solenoid valve. (See page 37)  
6
This hose connects to the Final Rinse  
Plumbing. (See page 44)  
7
5
4
3
8
10  
9
Item  
1
QTY  
Description  
Part Number  
1
2
2
2
2
2
1
1
1
3
1
BOOSTER HEATER  
SEE CHART BELOW  
04720‐003‐76‐09  
04730‐206‐13‐00  
04730‐002‐56‐27  
04730‐207‐04‐00  
04730‐011‐42‐96  
05975‐003‐77‐46  
05700‐003‐79‐40  
05975‐003‐77‐45  
06145‐003‐13‐97  
2
HOSE, 1/2 x 42" SS BRAIDED W/PTFE, MALE SWIVEL  
ELBOW, 3/4 NPT 90 DEGREE BRASS  
BUSHING, 3/4 MNPT x 1/2 FNPT HEX BRASS  
NIPPLE, 1/2 NPT x 4” LONG BRASS  
ELBOW, 1/2 NPT 90 DEGREE BRASS  
FITTING, 3/4 STRAIGHT QT SNAP (HEYCO‐8495)  
CONDUIT, FLEX2 1/2 x 24” LONG  
3
4
5
6
7
8
9
FITTING, 3/4 90 DEGREE QT SNAP (HEYCO‐8510)  
WIRE, 10AWG BLK SRML FIBERGLASS (3 FEET)  
10  
11  
SCHEMATIC (REFER TO THE BOOSTER HEATER SCHEMATIC PAGES FOR PART NUMBER)  
BOOSTER HEATER  
Part Number  
12 kW (40 degree F Rise) 208V 3‐PHASE  
12 kW (40 degree F Rise) 240V 3‐PHASE  
12 kW (40 degree F Rise) 480V 3‐PHASE  
12 kW (40 degree F Rise) 208V 1‐PHASE  
12 kW (40 degree F Rise) 240V 1‐PHASE  
17.3 kW (70 degree F Rise) 208V 3‐PHASE  
18 kW (70 degree F Rise) 240V 3‐PHASE  
18 kW (70 degree F Rise) 480V 3‐PHASE  
18 kW (70 degree F Rise) 208V 1‐PHASE  
18 kW (70 degree F Rise) 240V 1‐PHASE  
04540‐003‐76‐58  
04540‐003‐76‐60  
04540‐003‐76‐62  
04540‐003‐76‐57  
04540‐003‐76‐59  
04540‐003‐76‐64  
04540‐003‐76‐66  
04540‐003‐76‐68  
04540‐003‐76‐63  
04540‐003‐76‐64  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: STEAM BOOSTER HEATER OPTION  
22  
29  
21  
24  
28  
26  
30  
27  
26  
30  
26  
25  
24  
23  
26  
31  
32  
21  
20  
26  
22  
33  
26  
10  
1
2
34  
19  
15  
17  
11  
2
14  
16  
16  
15  
15  
12  
13  
3
14  
18  
4
17  
5
11  
4
14  
13  
6
4
12  
11  
7
10  
8
9
Item QTY  
Description  
Part Number  
04420‐002‐43‐94  
05306‐002‐89‐27  
06680‐500‐02‐77  
04730‐907‐01‐00  
04730‐912‐01‐00  
04730‐906‐10‐34  
04730‐002‐36‐81  
1
2
3
4
5
6
7
1
2
1
3
1
1
1
STEAM BOOSTER HEATER, ST‐T120  
U‐BOLT, 1/2‐13 THREAD, ZINC COADTED  
STEAM TRAP, 3/4 NPT‐F & T TYPE  
NIPPLE, CLOSE 3/4 NPT, BLACK IRON  
UNION, 3/4 NPT, BLACK IRON  
ELBOW, 90 DEG. 3/4 NPT, BLACK IRON  
REDUCER, 1‐1/2 NPT‐M x 3/4 NPT‐F, BLACK IRON  
Page Created: 06‐30‐2011  
Revised: N/A  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610-003-78-18)  
PARTS SECTION: STEAM BOOSTER HEATER OPTION (CONTINUED)  
Item QTY  
Description  
Part Number  
8
1
1
2
3
2
2
3
3
2
2
1
1
1
2
2
W‐PLATFORM, J120 STEAM BOOSTER  
REGULATING VALVE, 3/4 NPT‐F  
NIPPLE, 3/4 NPT x 6” LONG BRASS  
ELBOW, 90 DEG. 3/4 NPT BRASS  
NIPPLE, 3/4 NPT x 4” LONG BRASS  
UNION, 3/4 NPT BRASS  
05700‐002‐36‐72  
04820‐100‐01‐06  
05700‐001‐26‐74  
04730‐206‐13‐00  
04730‐207‐05‐00  
04730‐212‐05‐00  
04730‐207‐46‐00  
04730‐207‐34‐00  
04730‐011‐88‐80  
04730‐211‐01‐34  
04730‐011‐89‐19  
04820‐100‐07‐06  
04730‐211‐04‐00  
04810‐011‐72‐67  
06685‐111‐88‐34  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
NIPPLE, 3/4NPT x 2” LONG BRASS  
NIPPLE, CLOSE 3/4 NPT x 1‐3/8 NPT BRASS  
BUSHING, HEX 1 1/4 X 3/4 REDUCER  
TEE, BRASS, 3/4 X 3/4 X 3/4  
ADAPTER, 3/8 FNPT X 3/4 NPT BRASS  
VALVE, STEAM RELIEF 3/4 EDP‐0274751  
TEE, BRASS, 3/4 X 3/4 X 1/4  
VALVE, BALL TEST COCK 1/4 BRONZE  
PRESSURE GAUGE, 1/4 NPT‐M 0‐100 PSI  
23  
1
1
1
1
1
1
A‐CONTROL, J120 ASSEMBLY (MAJOR COMPONENTS ARE LISTED BELOW)  
THERMOSTAT, CORKSCREW 351‐254461  
SWITCH, DPDT  
LIGHT, SOLICO RED INDICATING  
TERMINAL BLOCK, 2‐POLE  
05700‐002‐98‐95  
06680‐500‐01‐77  
05930‐011‐49‐55  
05945‐111‐21‐57  
05940‐500‐09‐61  
05940‐200‐76‐00  
23A  
23B  
23C  
23D  
23F  
GROUND LUG  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
2
1
6
1
1
1
1
1
1
1
1
1
1
FITTING,3213 .231X.394 HEYCO  
05975‐011‐49‐03  
04730‐002‐36‐79  
04730‐907‐08‐34  
04730‐906‐03‐34  
04820‐100‐01‐35  
05700‐003‐22‐96  
04730‐904‐01‐04  
04730‐907‐14‐34  
04730‐217‐02‐32  
04730‐911‐01‐00  
04810‐002‐92‐23  
04730‐912‐01‐34  
04730‐911‐01‐34  
REDUCER, 1‐1/2 MNPT x 1 FNPT BLACK IRON  
NIPPLE, CLOSE 1 NPT X 2 BLACK IRON  
ELBOW, 1 NPT 90 DEG, BLACK IRON  
VALVE, SAFETY RELIEF 1 NPT  
COUPLING, 1/4 NPT BLACK IRON  
SIPHON TUBE,PIGTAIL 1/4NPT BLACK IRON  
Y'STRAINER, 1 NPT STEAM BLACK IRON  
TEE, 1 X 1 X 1/4 NPT, BLACK IRON  
VALVE, 120V 1" NPT BRONZE STEAM  
UNION, 1 NPT BLACK IRON  
TEE, 1” NPT BLACK IRON  
Page Created: 06‐30‐2011  
Revised: N/A  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
BOOSTER HEATER SCHEMATIC (3‐PHASE)  
USE THIS SCHEMATIC FOR THE FOLLOW‐  
ING BOOSTER HEATER OPTIONS:  
 208V 60HZ 3‐PHASE 12kW (40° RISE)  
 230V 60HZ 3‐PHASE 12kW (40° RISE)  
 460V 60HZ 3‐PHASE 12kW (40° RISE)  
 208V 60HZ 3‐PHASE 18kW (70° RISE)  
 230V 60HZ 3‐PHASE 18kW (70° RISE)  
 460V 60HZ 3‐PHASE 18kW (70° RISE)  
Page Created: 05‐04‐2010  
Revised: N/A  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
BOOSTER HEATER SCHEMATIC (1‐PHASE 12kW)  
USE THIS SCHEMATIC FOR THE FOLLOW‐  
ING BOOSTER HEATER OPTIONS:  
 208V 60HZ 1‐PHASE 12kW (40° RISE)  
 230V 60HZ 1‐PHASE 12kW (40° RISE)  
Page Created: 05‐04‐2010  
Revised: N/A  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
BOOSTER HEATER SCHEMATIC (1‐PHASE 18kW)  
USE THIS SCHEMATIC FOR THE FOLLOW‐  
ING BOOSTER HEATER OPTIONS:  
 208V 60HZ 1‐PHASE 18kW (70° RISE)  
 230V 60HZ 1‐PHASE 18kW (70° RISE)  
Page Created: 05‐04‐2010  
Revised: N/A  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
STEAM BOOSTER HEATER SCHEMATIC  
Page Created: 06‐30‐2011  
Revised: N/A  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
TEMPERATURE BOARD  
3
1
3
4
2
Item QTY  
Description  
Part Number  
1
2
3
4
1
1
8
1
CYCLIC TEMPERATURE BOARD  
GAUGE COVER, RED  
06685‐002‐74‐86  
05700‐002‐75‐62  
05310‐002‐83‐12  
09905‐003‐79‐03  
06680‐002‐16‐80  
NUT, THUMB 6‐32 NYLON  
DECAL, TEMPERATURE DISPLAY  
5
2 (44” Units) RTD TEMPERATURE PROBE (NOT SHOWN)  
3 (66” Units)  
Page Created: 05‐04‐2010  
Revised: 02‐25‐2011  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, PHOTOCELL TABLE LIMIT SWITCH OPTION  
WARNING:DO NOT CONNECT  
ENSURE RED/WHITE TO  
#12 OF R3 IS CONNECTED  
HERE  
FROM DOOR SWITCH  
RED / WHITE  
RED/WHITE TO #12 OF R3 HERE.  
ONLY CONNECT RED/WHITE  
TO INPUT #2OF PLC BOARD  
BROWN  
RED / WHITE  
DC+  
DOOR  
SIGNAL  
TABLE  
LIMIT  
C/O  
DRIVE  
C/O  
PLC  
DC-  
BLUE  
RED / WHITE  
BROWN  
RED / WHITE  
BLUE  
44  
14  
i2  
14  
14  
14  
14  
R4  
R2  
PLC1  
R1  
R6  
R3  
A2  
A2  
A2  
A2  
A1  
A1  
A2  
A1  
9
A1  
9
A1  
12  
9
9
9
RED  
RED / BLACK  
RED / BLACK  
RED / WHITE  
RED  
RED / WHITE  
BLUE  
PHOTO-EYE CABLE  
Page Created: 02‐25‐2011  
Revised: N/A  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 44” ELECTRICALLY HEATED (208/230/460 VOLT, 60 HZ, 3 PHASE)  
Page Created: 05‐04‐2010  
Revised: N/A  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 44” ELECTRICALLY HEATED (208/230 VOLT, 60 HZ, 1 PHASE)  
Page Created: 05‐04‐2010  
Revised: N/A  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 44” STEAM HEATED (208/230/460 VOLT, 60 HZ, 3 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 44” STEAM HEATED (208/230 VOLT, 60 HZ, 1 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 66” ELECTRICALLY HEATED (208/230/460 VOLT, 60 HZ, 3 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 66” ELECTRICALLY HEATED (208/230 VOLT, 60 HZ, 1 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 66” STEAM HEATED (208/230/460 VOLT, 60 HZ, 3 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
SCHEMATIC, 66” STEAM HEATED (208/230 VOLT, 60 HZ, 1 PHASE)  
Page Created: 02‐25‐2011  
Revised: N/A  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
ALABAMA  
CALIFORNIA  
P & D APPLIANCE  
GCS SERVICE INC.  
4220‐C ROSEVILLE ROAD  
NORTH HIGHLANDS, CA  
95660  
PHILADELPHIA, PA  
(215)925‐6217  
800‐441‐9115  
JONES‐McLEOD APPLIANCE  
SVC  
BARKERS FOOD MACHINERY  
SERVICES  
1616 7TH AVE. NORTH  
BIRMINGHAM, AL 35203  
(205) 251‐0159  
800‐821‐1150  
FAX: (205) 322‐1440  
service@jones‐mcleod.com  
5367 SECOND STREET  
IRWINDALE, CA 91706  
(626) 960‐9390  
800‐258‐6999  
FAX: (626) 337‐4541  
service@barkers.com  
(916) 974‐2772  
800‐824‐7219  
FAX:(916) 974‐2774  
FAX: (215) 925‐6208  
ELMER SCHULTZ SERVICE  
36 BELMONT AVE.  
WILLMINGTON, DE 19804  
(302) 655‐8900  
COMMERCIAL APPLIANCE  
SERVICE, INC.  
281 LATHROP WAY, #100  
SACRAMENTO, CA 95815  
(916) 567‐0203  
(800) 464‐2222  
(916) 567‐0324 FAX  
800‐225‐0599  
FAX: (302) 656‐3673  
elmer2@erols.com  
JONES‐McLEOD APPLIANCE  
SVC  
854 LAKESIDE DRIVE  
MOBILE, AL 36693  
(251) 666‐7278  
GCS SERVICE INC.  
LOS ANGELES, CA  
(213) 683‐2090  
800‐327‐1433  
FAX: (213) 683‐2099  
EMR SERVICE DIVISION  
106 WILLIAMSPORT CIRCLE  
SALISBURY, MD 21804  
(410) 543‐8197  
800‐237‐9859  
FAX: (251) 661‐0223  
COLORADO  
GCS SERVICE INC.  
SANTA ANA, CA  
(714) 542‐1798  
GCS SERVICE INC.  
SHERIDAN, CO  
FAX: (410) 548‐4038  
ALASKA  
800‐540‐0719  
FAX: (714) 542‐4787  
(303) 371‐9054  
800‐972‐5314  
FLORIDA  
RESTAURANT APPLIANCE  
SERVICE  
7219 ROOSEVELT WAY NE  
SEATTLE, WA 98115  
(206) 524‐8200  
800‐433‐9390  
FAX: (206) 525‐2890  
info@restappl.com  
FAX: (303) 371‐4754  
COMMERCIAL APPLIANCE  
SERVICE  
8416 LAUREL FAIR CIRCLE  
BLDG 6, SUITE 114  
TAMPA, FL 33610  
(813) 663‐0313  
GCS SERVICE INC.  
S. SAN FRANCISCO, CA  
(650) 635‐0720  
800‐969‐4427  
FAX: (650) 871‐4019  
HAWKINS COMMERCIAL  
APPLIANCE SERVICE  
3000 S. WYANDOT ST.  
ENGLEWOOD, CO 80110  
(303) 781‐5548  
800‐282‐4718  
COMMERCIAL APPLIANCE  
SERVICE, INC.  
6507 PACIFIC AVENUE,  
(800) 624‐2117  
FAX: (303) 761‐5561  
johns@hawkinscommercial.com  
FAX: (813) 663‐0212  
commercialappliance@world‐  
net.aꢀ.net  
ARIZONA  
AUTHORIZED COMMERCIAL  
FOOD EQMT. SVC  
4832 SOUTH 35TH STREET  
PHOENIX, AZ 85040  
(602) 234‐2443  
Suite 102  
STOCKTON, CA 95207  
(916) 567‐0203  
(800) 464‐2222  
(916) 567‐0266 FAX  
METRO APPLIANCE SERVICE  
1640 S BROADWAY  
DENVER, CO 80210  
(303) 778‐1126  
GCS SERVICE INC  
MIAMI, FL  
(305) 621‐6666  
800‐766‐8966  
800‐824‐8875  
800‐525‐3532  
FAX: (305) 621‐6656  
FAX: (602) 232‐5862  
acsboss@aol.com  
GCS SERVICE INC.  
SAN DIEGO, CA  
(858) 549‐8411  
800‐422‐7278  
FAX: (303) 778‐0268  
metroappls@aol.com  
GCS SERVICE INC  
ORLANDO, FL  
(407) 841‐2551  
800‐338‐7322  
GCS SERVICE INC.  
PHOENIX, AZ  
CONNECTICUT  
FAX: (858) 549‐2323  
(602) 474‐4510  
800‐510‐3497  
FAX: (602) 470‐4511  
GCS SERVICE INC.  
HARTFORD, CT  
(860) 549‐5575  
800‐423‐1562  
FAX: (407) 423‐8425  
INDUSTRIAL ELECTRIC SVC.  
5662 ENGINEER DRIVE  
HUNTINGTON BEACH, CA  
92649  
NASS PARTS AND SERVICE, INC.  
1144 BELVILLE ROAD, UNIT 359  
DAYTONA BEACH, FL 32114  
(386) 226‐2642  
ARKANSAS  
FAX: (860) 527‐6355  
(714) 379‐7100  
BROMLEY PARTS & SVC  
10TH AND RINGO  
P.O. BOX 1688  
LITTLE ROCK, AR 72202  
(501) 374‐0281  
800‐482‐9269  
FAX: (501) 374‐8352  
service@bromleyparts.com  
parts@bromleyparts.com  
(800‐457‐3783  
FAX: (714) 379‐7109  
SUPERIOR KITCHEN SERVICE INC.  
22 THOMPSON ROAD  
WINDSOR, CT 06088  
(888) 590‐1899  
(800) 432‐2795  
(386) 736‐7695 FAX  
P & D APPLIANCE SVC  
100 SOUTH LINDEN AVE.  
S. SAN FRANCISCO, CA 94080  
(650) 635‐1900  
800‐424‐1414  
FAX: (650) 635‐1919  
pndappl@aol.com  
GCS SERVICE INC  
TAMPA, FL  
(813) 626‐6044  
800‐282‐3008  
(888) 590‐1996 FAX  
DELAWARE  
FAX: (813) 621‐1174  
FOOD SERVICE EQMT.  
2101 PARKWAY SOUTH  
BROOMALL, PA 19008  
(610) 356‐6900  
FAX: (610) 356‐2038  
dancerule@aol.com  
GCS SERVICE,INC.  
3717 CHERRY ROAD  
MEMPHIS, TN 38118  
(901) 366‐4587  
800‐262‐9155  
FAX: (901) 366‐4588  
Page Created: 07‐06‐2011  
Revised: N/A  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
INDIANA  
JONES‐McLEOD APPLIANCE SVC  
HAWAII  
CERTIFIED SERVICE CENTER  
854 LAKESIDE DRIVE  
MOBILE, AL 36693  
(251) 666‐7278  
800‐237‐9859  
FAX: (251) 661‐0223  
service@jones‐mcleod.com  
1051 GOODWIN DRIVE  
LEXINGTON, KY 40505  
(606) 254‐8854  
800‐432‐9269  
FAX: (606) 231‐7781  
jatkins@cerꢁfiedsc.com  
FOOD EQMT. PARTS &  
SERVICE CO.  
300 PUUHALE RD.  
HONOLULU, HI 96819  
(808) 847‐4871  
GCS SERVICE INC.  
INDIANAPOLIS, IN  
(317) 545‐9655  
800‐727‐8710  
FAX: (317) 549‐6286  
FAX: (808) 842‐1560  
NASS PARTS AND SERVICE, INC.  
1108 SOUTH WOODS AVENUE  
ORLANDO, FL 32805  
(407) 425‐2681  
fepsco@hula.net  
GCS SERVICE INC.  
B622 LA PAS TRAIL  
INDIANAPOLIS, IN 46268  
(317) 290‐8060  
GCS SERVICE INC.  
LOUISVILLE, KY  
(502) 367‐1788  
800‐752‐6160  
IDAHO  
(800) 432‐2795  
RESTAURANT APPLIANCE SVC.  
(800) 410‐9794  
FAX: (502) 367‐0400  
(407) 425‐3463 FAX  
7219 ROOSEVELT WAY NE  
(317) 290‐8085 FAX  
SEATTLE, WA 98115  
(206) 524‐8200  
800‐433‐9390  
FAX: (206) 525‐2890  
info@restappl.com  
GCS SERVICE INC.  
LEXINGTON, KY  
(606) 255‐0746  
800‐432‐9260  
NASS PARTS AND SERVICE, INC.  
1376 HEIDE AVENUE  
PALM BAY, FL 32907  
(321) 952‐2012  
(800) 432‐2795  
(321) 953‐0266 FAX  
IOWA  
GOODWIN TUCKER GROUP  
2900 DELAWARE AVENUE  
DES MOINES, IA 50317  
(515) 262‐9308  
FAX: (606) 255‐0748  
RON'S SERVICE  
LOUISIANA  
703 E 44TH STREET STE 10  
GARDEN CITY, ID 83714  
(208) 375‐4073  
800‐372‐6066  
FAX: (515) 262‐2936  
parts@goodwintucker.com  
GEORGIA  
HERITAGE SERVICE GROUP  
1532 RIVER OAKS WEST  
NEW ORLEANS, LA 70123  
(504) 734‐8864  
(800) 499‐2351  
(504) 733‐2559 FAX  
GCS SERVICE INC  
ATLANTA, GA  
(770) 452‐7322  
800‐334‐3599  
FAX: (208) 375‐4402  
CONES REPAIR SVC.  
1056 27TH AVENUE SW  
CEDAR RAPIDS, IA 52404  
(319) 365‐3325  
ILLINOIS  
FAX: (770) 452‐7473  
CONES REPAIR SVC.  
2408 40TH AVE.  
MOLINE, IL 61265  
(309) 797‐5323  
800‐716‐7070  
FAX: (309)797‐3631  
jackb@cones.com  
800‐747‐3326  
FAX: (319) 365‐0885  
MAINE  
HERITAGE FOODSERVICE GROUP  
OF ATLANTA  
2100 NORCROSS PKWY. SUITE 130  
NORCROSS, GA 30071  
(770) 368‐1465  
GCS SERVICE INC.  
CHELSEA, MA  
(617) 889‐9393  
800‐225‐1155  
KANSAS  
GCS SERVICE INC.  
KANSAS CITY, MO  
(816) 920‐5999  
866‐388‐9837  
FAX: (866) 388‐9838  
FAX: (617) 889‐1222  
EICHENAUER SERVICES INC.  
130 S OAKLAND ST.  
DECATUR, IL 62522  
(217) 429‐4229  
800‐252‐5892  
FAX: (217) 429‐0226  
esi@esiquality.com  
800‐229‐6477  
FAX: (816) 920‐7387  
MASSACHUSETTS RESTAURANT  
SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868‐1930  
WHALEY FOODSERVICE REPAIRS  
109‐A OWENS INDUSTRIAL DRIVE  
SAVANNAH, GA 31405  
(912) 447‐0827  
888‐765‐0036  
FAX: (912) 447‐0826  
GENERAL PARTS, INC.  
1101 E. 13TH STREET  
KANSAS CITY, MO 64106  
(816) 421‐5400  
800‐338‐6737  
FAX: (617) 686‐5331  
GCS SERVICE INC.  
ELMHURST, IL  
(630) 941‐7800  
800‐942‐9689  
(800) 279‐9967  
(816) 421‐1270 FAX  
PIERCE PARTS & SERVICE  
2422 ALLEN ROAD  
MACON, GA 31216  
(478) 781‐6003  
PINE TREE FOOD EQUIPMENT  
175 LEWISTON ROAD  
GRAY, ME 04039  
KENTUCKY  
FAX: (630) 941‐6048  
(207) 657‐6400  
800‐368‐2512  
FAX: (478) 781‐7186  
CERTIFIED SERVICE CENTER  
127 DISHMAN LANE  
BOWLING GREEN, KY 42101  
(270) 783‐0012  
(800) 540‐5427  
(207) 657‐5464 FAX  
GCS SERVICE INC.  
ST. LOUIS, MO  
(314) 683‐7444  
800‐284‐4427  
MARYLAND  
(877) 907‐0012  
FAX: (314) 638‐0135  
FAX: (270) 783‐0058  
EMR SERVICE DIVISION  
700 EAST 25TH STREET  
BALTIMORE, MD 21218  
(410) 467‐8080  
800‐879‐4994  
FAX: (410) 467‐4191  
baltparts@emrco.com  
GENERAL PARTS, INC.  
248 JAMES STREET  
BENSONVILLE, IL 60106  
(630) 595‐3300  
CERTIFIED SERVICE CENTER  
RAMCO BUSINESS PARK  
4283 PRODUCE ROAD  
LOUISVILLE, KY 40218  
(502) 964‐7007  
(800) 880‐3604  
FAX: (630)595‐0006  
800‐637‐6350  
FAX: (502) 964‐7202  
cwalker@cerꢁfiedsc.com  
droenigk@cerꢁfiedsc.com  
Page Created: 07‐06‐2011  
Revised: N/A  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
EMR SERVICE DIVISION  
106 WILLIAMSPORT CIRCLE  
SALISBURY, MD 21804  
(410) 543‐8197  
MICHIGAN  
GCS SERVICE INC.  
ST. LOUIS, MO  
(314) 638‐7444  
800‐284‐4427  
NEW HAMPSHIRE  
GCS SERVICE INC.  
LIVONIA, MI  
GCS SERVICE INC.  
CHELSEA, MA  
888‐687‐8080  
FAX: (410) 548‐4038  
baltparts@emrco.com  
(248) 426‐9500  
800‐772‐2936  
FAX: (248) 426‐7555  
FAX: (314) 638‐0135  
(617)889‐9393  
800‐225‐1155  
FAX: (617) 889‐1222  
KAEMMERLIN PARTS & SVC.  
2728 LOCUST STREET  
ST. LOUIS, MO 63103  
(314) 535‐2222  
FAX: (314) 535‐6205  
petek@kps.stl.com  
EMR SERVICE DIVISION  
5316 Sunnyside Ave.  
Beltsville, MD 20715  
(301) 931‐7000  
JACKSON SERVICE COMPANY  
3980 BENSTEIN RD.  
COMMERCE TWSHP, MI 48382  
(248) 363‐4159  
ACE SERVICE CO.  
95 HAMPTON AVE.  
NEEDHAM, MA 02494  
(781) 449‐4220  
800‐348‐2365  
FAX: (301) 931‐3060  
baltparts@emrco.com  
800‐332‐4053  
FAX: (248) 363‐5448  
800‐225‐4510 MA & NH  
FAX: (781) 444‐4789  
taceservice@aol.com  
GENERAL PARTS, INC.  
1101 EAST 13TH STREET  
KANSAS CITY, MO 64106  
(816) 421‐5400  
(800) 279‐9967  
(816) 421‐1270 FAX  
GCS SERVICE INC.  
GRAND RAPIDS, MI  
(616) 241‐0200  
800‐823‐4866  
FAX: (616) 241‐0541  
GCS SERVICE INC.  
SILVER SPRING, MD  
(301) 585‐7550 (DC)  
(410) 792‐0338 (BALT)  
(800) 638‐7278  
MASSACHUSETTS RESTAURANT  
SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868‐1930  
MONTANA  
FAX: (301) 495‐4410  
MINNESOTA  
800‐338‐6737  
RESTAURANT APPLIANCE SVC.  
FAX: (617) 868‐5331  
MASSACHUSETTS  
GCS SERVICE INC.  
7219 ROOSEVELT WAY NE  
MINNEAPOLIS, MN  
(612) 546‐4221  
SEATTLE, WA 98115  
(206) 524‐8200  
NEW JERSEY  
ACE SERVICE CO.  
95 HAMPTON AVE.  
NEEDHAM, MA 02494  
(781) 449‐4220  
800‐225‐4510 MA & NH  
FAX: (781) 444‐4789  
taceservice@aol.com  
800‐345‐4221  
FAX: (612) 546‐4286  
800‐433‐9390  
FAX: (206) 525‐2890  
info@restappl.com  
JAY HILL REPAIRS  
90 CLINTON RD.  
FAIRFIELD, NJ 07004  
(973) 575‐9145  
800‐836‐0643  
FAX: (973) 575‐5890  
jhrepair@aol.com  
GENERAL PARTS, INC.  
11311 HAMPSHIRE AVENUE SOUTH  
BLOOMINGTON, MN 55438‐2456  
(952) 944‐5800  
(800) 279‐9980  
(800) 279‐9980 FAX  
NEBRASKA  
GOODWIN ‐ TUCKER GROUP  
7535 D STREET  
OMAHA, NE 68124  
(402) 397‐2880  
800‐228‐0342  
FAX: (402) 397‐2881  
askme@goodwintucker.com  
MASSACHUSETTS RESTAURANT  
SUPPLY  
34 SOUTH STREET  
SOMERVILLE, MA 02143  
(617) 868‐1930  
GCS SERVICE INC.  
EAST RUTHERFORD, NJ  
(973) 614‐0003  
800‐399‐8294  
FAX: (973) 614‐0230  
MISSISSIPPI  
800‐338‐6737  
GCS SERVICE INC.  
FAX: (617) 868‐5331  
JACKSON, MS  
(601) 956‐7800  
800‐274‐5954  
FAX: (601) 956‐1200  
NEVADA  
GCS SERVICE INC.  
PHILADELPHIA, PA  
(215) 925‐6217  
800‐441‐9115  
FAX: (215) 925‐6208  
GCS SERVICE INC.  
CHELSEA, MA  
(617) 889‐9393  
800‐225‐1155  
HI TECH COMMERCIAL SERVICE  
1840 STELLA LAKE STREET  
NORTH LAS VEGAS, NV 89106  
(702) 649‐4616  
GCS SERVICE INC.  
MEMPHIS, TN  
FAX: (617) 889‐1222  
(901) 366‐4587  
800‐262‐9155  
FAX: (901) 366‐4588  
(877) 924‐4832  
FAX: (702) 649‐4607  
larry@hitechnv.com  
ELMER SCHULTZ SERVICES  
201 W. WASHINGTON AVE.  
PLEASANTVILLE, NJ 08232  
(609) 641‐0317  
800‐378‐1641  
FAX:(609) 641‐8703  
elmer2@erols.com  
GCS SERVICE INC.  
HARTFORD, CT  
(860) 549‐5575  
800‐723‐1562  
MISSOURI  
HI TECH COMMERCIAL SERVICE  
5454 LOUIE LANE  
RENO, NV 89511  
(775) 852‐9696  
FAX: (775) 852‐5104  
FAX: (860) 527‐6355  
GCS SERVICE INC.  
KANSAS CITY, MO  
(816) 920‐5999  
SUPERIOR KITCHEN SERVICE INC.  
399 FERRY STREET  
NEW YORK  
EVERETT, MA 02149  
(617) 389‐1899  
(888) 590‐1899  
800‐229‐6477  
FAX: (816) 920‐7387  
GCS SERVICE INC.  
LAS VEGAS, NV  
(702) 450‐3495  
APPLIANCE INSTALLATION  
AND SERVICE CORP.  
1336 MAIN STREET  
(617) 389‐1996 FAX  
800‐500‐9060  
BUFFALO, NY 14209  
(716) 884‐7425  
FAX: (702) 450‐3491  
800‐722‐1252  
FAX: (716) 884‐0410  
ais@worldnet.aꢀ.net  
Page Created: 07‐06‐2011  
Revised: N/A  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
B.E.S.T. INC.  
AUTHORIZED APPLIANCE  
OHIO  
OREGON  
3003 GENESEE STREET  
BUFFALO, NY 14225  
(716) 893‐6464  
800‐338‐5011  
FAX: (716) 893‐6466  
bestserv@aol.com  
SERVICECENTER  
904 S. MARSHALL ST.  
WINSTON‐SALEM, NC 27403  
(336) 725‐5396  
CERTIFIED SERVICE CENTER  
890 REDNA TERRACE  
CINCINNATI, OH 45215  
(513) 772‐6600  
RON'S SERVICE  
16364 SW 72ND AVE  
PORTLAND, OR 97224  
(503) 624‐0890  
FAX:(336) 721‐1289  
800‐543‐2060  
800‐851‐4118  
AUTHORIZED APPLIANCE  
SERVICECENTER  
FAX: (513) 612‐6600  
sbarasch@cerꢁfiedsc.com  
FAX: (503) 684‐6107  
lrobinson@ronsservice.com  
DUFFY'S EQUIPMENT SVC.  
3138 ONEIDA STREET  
SAUQUOIT, NY 13456  
(315) 737‐9401  
800‐443‐8339  
FAX: (315) 737‐7132  
duffyequip@aol.com  
104 HINTON AVE.  
WILMINGTON, NC 28403  
(910) 313‐1250  
CERTIFIED SERVICE CENTER  
171J‐K NORTH HAMILTON RD.  
COLUMBUS, OH 43213  
(614) 751‐3769  
(866) 862‐1252  
FAX: (614) 751‐5792  
jadkins@cerꢁfiedsc.com  
PENNSYLVANIA  
FAX:(910) 313‐6130  
A.I.S. COMMERCIAL PARTS &  
SERVICE  
1816 WEST 26TH STREET  
ERIE, PA 16508  
(814) 456‐3732  
800‐332‐3732  
WHALEY FOODSERVICE  
8334‐K ARROWRIDGE BLVD  
CHARLOTTE, NC 28273  
(704) 529‐6242  
FAX: (704) 529‐1558  
info@whaleyfoodservice.com  
NORTHERN PARTS & SVC.  
21 NORTHERN AVENUE  
PLATTSBURGH, NY 12903  
(518) 563‐3200  
800‐634‐5005  
FAX: (800) 782‐5424  
info@northernparts.com  
CERTIFIED SERVICE CENTER  
6025 N. DIXIE DRIVE  
DAYTON, OH 45414  
(937) 898‐4040  
(800) 257‐2611  
FAX: (937) 898‐4177  
dharvey@cerꢁfiedsc.com  
FAX: (814) 452‐4843  
aiserie@aol.com  
WHALEY FOODSERVICE REPAIRS  
203‐D CREEK RIDGE RD.  
GREENSBORO, NC 27406  
(336) 333‐2333  
FAX: (336) 333‐2533  
info@whaleyfoodservice.com  
ELMER SCHULTZ SVC.  
540 NORTH 3RD STREET  
PHILADELPHIA, PA 19123  
(215) 627‐5400  
FAX: (215) 627‐5408  
elmer2@erols.com  
GCS SERVICE INC.  
BROOKLYN, NY  
(718) 486‐5220  
800‐969‐4271  
COMMERCIAL PARTS & SVC.  
OF COLUMBUS  
FAX: (718) 486‐6772  
WHALEY FOODSERVICE REPAIRS  
335‐105 SHERWEE DRIVE  
RALEIGH, NC 27603  
(919) 779‐2266  
FAX: (919) 779‐2224  
5033 TRANSAMERICA DRIVE  
COLUMBUS, OH 43228  
(614) 221‐0057  
800‐837‐8327  
FAX: (614) 221‐3622  
GCS SERVICE INC.  
PHILADELPHIA, PA  
(215) 925‐6217  
800‐441‐9115  
FAX: (215) 925‐6208  
ALL SERVICE KITCHEN  
EQUIPMENT REPAIR  
10 CHARLES ST.  
NEW HYDE PARK, NY 11040  
(516) 378‐1176  
FAX: (516) 378‐1735  
info@whaleyfoodservice.com  
GCS SERVICE INC.  
COLUMBUS, OH  
(614) 476‐3225  
800‐282‐5406  
GCS SERVICE INC.  
HARRISBURG, PA  
(717) 564‐3282  
800‐367‐3225  
FAX: (717) 564‐9286  
WHALEY FOODSERVICE REPAIRS  
6418‐101 AMSTERDAM WAY  
WILMINGTON, NC 28405  
(910) 791‐0000  
ALL ISLAND REPAIRS  
40‐9 BURT DRIVE  
FAX: (614) 476‐1196  
DEER PARK, NY 11729  
(631) 242‐5588  
FAX: (631) 242‐6102  
FAX: (910) 791‐6662  
info@whaleyfoodservice.com  
ELECTRICAL APPLIANCE  
REPAIR SVC.  
5805 VALLEY BELT ROAD  
CLEVELAND, OH 44131  
(216) 459‐8700  
800‐621‐8259  
FAX: (216) 459‐8707  
tomr@electapplrep.com  
GCS SERVICE INC.  
PITTSBURGH, PA  
(412) 787‐1970  
800‐738‐1221  
NORTH DAKOTA  
NORTH CAROLINA  
GCS SERVICE INC.  
MINNEAPOLIS, MN  
(612) 546‐4221  
800‐345‐4221  
FAX: (612) 546‐4286  
FAX: (412) 787‐5005  
AUTHORIZED APPLIANCE  
SERVICECENTER  
1020 TUCKASEEGEE RD.  
CHARLOTTE, NC 28208  
(704) 377‐4501  
K & D PARTS AND SERVICE CO.  
1833‐41 N CAMERON STREET  
HARRISBURG, PA 17103  
(717) 236‐9039  
OKLAHOMA  
(800) 532‐6127  
FAX:(704) 377‐4504  
GENERAL PARTS, INC.  
10 SOUTH 18TH STREET  
FARGO, ND 58103  
(701) 235‐4161  
(800) 279‐9987  
(701) 235‐0539 FAX  
800‐932‐0503  
FAX: (717) 238‐4367  
kdparts‐service@paonline.com  
HAGAR RESTAURANT EQMT.  
1229 W MAIN STREET  
OKLAHOMA CITY, OK 73106  
(405) 235‐2184  
800‐445‐1791  
FAX: (405) 236‐5592  
AUTHORIZED APPLIANCE  
SERVICECENTER  
800 N. PERSON ST.  
RALEIGH, NC 27604  
CLARK SERVICE & PARTS  
306 AIRPORT DRIVE  
BOX 10  
(919) 834‐3476  
SMOKETOWN, PA 17576  
(717) 392‐5590  
FAX:(919) 834‐3477  
(717) 392‐5735  
Page Created: 07‐06‐2011  
Revised: N/A  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
RHODE ISLAND  
WHALEY FOODSERVICE REPAIRS  
4740‐A FRANCHISE STREET  
N. CHARLESTON, SC 29418  
(843) 760‐2110  
GCS SERVICE INC.  
HOUSTON, TX  
(713)785‐9187  
800‐868‐6957  
GCS SERVICE INC.  
VIRGINIA BEACH, VA  
(757) 464‐3500  
800‐476‐4278  
FAX: (757) 464‐4106  
GCS SERVICE INC.  
EAST PROVIDENCE, RI  
(401) 434‐6803  
FAX: (843) 760‐2255  
FAX: (713) 785‐3979  
800‐462‐6012  
info@whaleyfoodservice.com  
FAX: (401) 438‐9400  
GCS/STOVE PARTS  
2120 SOLANA STREET  
FORT WORTH, TX 76117  
(817) 831‐0381  
800‐433‐1804  
FAX: (817) 834‐7754  
bud@stoveparts.com  
WASHINGTON  
SOUTH DAKOTA  
SUPERIOR KITCHEN SERVICE INC.  
669 ELMWOOD AVENUE  
PROVIDENCE, RI 02907  
(888) 590‐1899  
GCS SERVICE INC.  
SEATTLE, WA  
(206) 763‐0353  
800‐211‐4274  
GCS SERVICE INC.  
MINNEAPOLIS, MN  
(612) 546‐4221  
(401) 781‐1996 FAX  
800‐345‐4221  
FAX: (206) 763‐5943  
FAX: (612) 546‐4286  
SOUTH CAROLINA  
UTAH  
RESTAURANT APPLIANCE  
SERVICE  
7219 ROOSEVELT WAY, NE  
SEATTLE, WA 98115  
(206) 524‐8200  
800‐433‐9390  
FAX: (206) 525‐2890  
info@restappl.com  
GENERAL PARTS, INC.  
10 SOUTH 18TH STREET  
FARGO, ND 58103  
(701) 235‐4161  
(800) 279‐9987  
(701) 235‐0539 FAX  
AUTHORIZED APPLIANCE  
SERVICECENTER  
1811 TAYLOR ST.  
COLUMBIA, SC 29202  
(803) 254‐8414  
FAX: (803) 254‐5146  
LA MONICA'S RESTAURANT  
EQUIPMENT SVC.  
6182 SOUTH STRATLER AVE.  
MURRAY, UT 84107  
(801) 263‐3221  
800‐527‐2561  
TENNESSEE  
FAX: (801) 263‐3229  
lamonica81@aol.com  
AUTHORIZED APPLIANCE  
SERVICECENTER  
2249 AUGUSTA RD.  
GREENVILLE, SC 29605  
(864) 235‐9616  
WEST VIRGINIA  
GCS SERVICE INC.  
MEMPHIS, TN  
(901) 366‐4587  
800‐262‐9155  
VERMONT  
STATEWIDE SERVICE, INC.  
603 MAIN AVE.  
NITRO, WV 25143  
(304) 755‐1811  
NORTHERN PARTS & SVC.  
4874 S. CATHERINE STREET  
FAX: (864) 235‐9623  
FAX: (901) 366‐4588  
PLATTSBURGH, NY 12901  
(518) 563‐3200  
800‐634‐5005  
FAX: (800) 782‐5424  
info@northernparts.com  
(800) 441‐9739  
FAX: (304) 755‐4001  
sws3182@aol.com  
WHALEY FOODSERVICE REPAIRS  
I 26&US1  
P.O. BOX 4023  
GCS SERVICE INC.  
NASHVILLE, TN  
(615) 244‐8050  
800‐831‐7174  
WEST COLUMBIA, SC 29170  
WISCONSIN  
(803) 791‐4420  
FAX: (615) 244‐8885  
800‐877‐2662  
FAX: (803) 794‐4630  
info@whaleyfoodservice.com  
GCS SERVICE INC.  
CHELSEA, MA  
(617)889‐9393  
800‐225‐1155  
APPLIANCE SERVICE  
CENTER, INC.  
2439 ATWOOD AVE  
MADISON, WI 53704  
(608) 246‐3160  
800‐236‐7440  
FAX: (608) 246‐2721  
ascmad@execpc.com  
TEXAS  
ARMSTRONG REPAIR CENTER  
5110 GLENMOUNT DRIVE  
HOUSTON, TX 77081  
(713) 666‐7100  
WHALEY FOODSERVICE REPAIRS  
748 CONGAREE ROAD  
GREENVILLE, SC 29607  
(864) 234‐7011  
FAX: (617) 889‐1222  
VIRGINIA  
800‐392‐5325  
800‐494‐2539  
FAX: (864) 234‐6662  
info@whaleyfoodservice.com  
FAX: (713) 661‐0520  
gm@armstrongrepair.com  
DAUBERS, INC.  
7645 DYNATECH COURT  
SPINGFIELD, VA 22153  
(703) 866‐3600  
800‐554‐7788  
FAX: (703) 866‐4071  
daubers@aol.com  
APPLIANCE SERVICE  
CENTER, INC.  
6843 W. BELOIT RD.  
WEST ALLIS, WI 53219  
(414) 543‐6460  
COMMERCIAL KITCHEN REPAIR CO.  
1377 N BRAZOS  
P.O BOX 831128  
SAN ANTONIO, TX 78207  
(210) 735‐2811  
WHALEY FOODSERVICE REPAIRS  
1406‐C COMMERCE PL.  
MYRTLE BEACH, SC 29577  
(843) 626‐1866  
800‐236‐6460  
FAX: (414) 543‐6480  
ascmil@execpc.com  
FAX: (843) 626‐2632  
800‐292‐2120  
GCS SERVICE INC.  
info@whaleyfoodservice.com  
FAX: (210) 735‐7421  
SILVER SPRING, MD  
brock@commercialkitchen.com  
(301) 585‐7550(DC)  
APPLIANCE SERVICE  
(410) 792‐0388(BALT)  
800‐638‐7278  
FAX: (301)495‐4410  
CENTER  
GCS SERVICE INC.  
DALLAS, TX  
(972) 484‐2954  
800‐442‐5026  
786 MORRIS AVE  
GREEN BAY, WI 54304  
(920) 496‐9993  
800‐236‐0871  
GCS SERVICE INC.  
FAX: (972) 484‐2531  
RICHMOND, VA  
FAX: (920) 496‐9927  
(804) 672‐1700  
800‐899‐5949  
ascfox@execpc.com  
FAX: (804) 672‐2888  
Page Created: 07‐06‐2011  
Revised: N/A  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Manual (07610‐003‐78‐18)  
MAINTENANCE & REPAIR CENTERS  
GENERAL PARTS, INC.  
W223 N735 SARATOGA DRIVE  
WAUKESHA, WI 53186  
(262) 650‐6666  
(800) 279‐9946  
(262) 650‐6660 FAX  
WYOMING  
HAWKINS COMMERCIAL  
APPLIANCE SERVICE  
3000 S. WYANDOT ST.  
ENGLEWOOD, CO 80110  
(303) 781‐5548  
(800) 624‐2117  
FAX: (303) 761‐5561  
johns@hawkinscommercial.com  
METRO APPLIANCE SERVICE  
1640 S BROADWAY  
DENVER, CO 80210  
(303) 778‐1126  
800‐525‐3532  
FAX: (303) 778‐0268  
metroappls@aol.com  
INTERNATIONAL  
GLOBAL PARTS AND SUPPLY  
7758 NW 72ND ST  
MIAMI, FL 33166  
(305) 885‐6353  
H.D. SHELDON AND CO  
19 UNION SQUARE, WEST  
NEW YORK, NY 10003  
(212) 627‐1759  
(212) 924‐6920  
CANADA  
THE GARLAND GROUP  
1177 KAMATO ROAD  
MISSISSAUGA, ONTARIO L4W 1X4  
(905) 206‐8380  
SALES  
(905) 624‐1419  
FAX: (905) 624‐1851  
SERVICE  
800‐427‐6668  
FAX: 800‐361‐7745  
Page Created: 07‐06‐2011  
Revised: N/A  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Impact Driver 2131 User Manual
Insignia Radio NS HD01A User Manual
Invacare Mobility Aid Lynx L 3X User Manual
Jenn Air Ventilation Hood MK7030 User Manual
JVC DVD Player XV N310B XV N312S User Manual
JVC DVD Recorder CU VD3U User Manual
JVC Portable Speaker SP XF51 User Manual
Kenmore Range 66595822 User Manual
Kenwood Speaker System HM 381MD User Manual
Korg DJ Equipment PX4A User Manual