VSIDREO C-AVSS1ET0TE1REUCOSRDER
INSTRUCTIONS
REW
FF
24HR QUICK
REC LINK PROGRAM
POWER
INSERT A.DUB
S-VIDEO
LPT0887-001A
WARNING:
Dear Customer,
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
Thank you for purchasing the JVC S-VHS video cassette
recorder. Before use, please read the safety information and
precautions to ensure safe use of your new VCR.
CAUTION:
This video cassette recorder should be used with AC 120Vd,
60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any
other power source.
CAUTIONS
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
For Customer Use:
Enter below the Model No. and Serial No. which are located
on the rear of cabinet. Retain this information for future
reference.
Model No.
Serial No.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Power Lines
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
An outside antenna
system should not be
located in the vicinity of
overhead power lines or
other electric light or
power circuits, or where
it can fall into such
power lines or circuits.
When installing an
outside antenna system,
extreme care should be
taken to keep from
touching such power
lines or circuits as
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock or other hazards.
contact with them might
be fatal.
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
USE
1. Accessories
To avoid personal injury:
● Do not place this product on an unstable cart, stand, tripod,
bracket, or table. It may fall, causing serious injury to a child or
adult, and serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
● Use a mounting accessory recommended by the manufacturer
and follow the manufacturer’s instructions for any mounting of
the product.
● Do not try to roll a cart with small casters across thresholds or
deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should
be moved with care. Quick stops,
How to use the Remote
Before use, insert two AA size batteries into the Remote with the
polarity ( and ) matched correctly as indicated on the battery
compartment or on the lid.
The Remote can operate most of your VCR’s functions, as well as
basic functions of TV sets, cable boxes and DBS receivers.
● Point the Remote toward the remote sensor on the target
component.
● The maximum operating distance of the Remote is about 8 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for
a few seconds, replace the batteries and then try again.
excessive force, and uneven surfaces may
cause the product and cart combination
to overturn.
Video heads cleaning
3. Water and Moisture
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity.
● in a dusty environment
Do not use this product near water—for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and
the like.
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Use a dry cleaning cassette — TCL-2 — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“ON SCREEN (PLAY)” set to “ON” (੬ pg. 18)).
4. Object and Liquid Entry
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any
kind on the product.
5. Attachments
Usable cassettes
Do not use attachments not recommended by the manufacturer of
this product as they may cause hazards.
6. Cleaning
● Compact VHS camcorder recordings can
be played on this VCR. Simply place the
recorded cassette into a VHS Cassette
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
Adapter and it can be used just like any
full-sized VHS cassette.
● This VCR can record on regular VHS and Super VHS cassettes.
While only VHS signals can be recorded on regular VHS
cassettes*, both VHS and Super VHS signals can be recorded
and played back using Super VHS cassettes.
* By using the S-VHS ET function, it is possible to record and play back
with S-VHS picture quality on VHS cassettes with this VCR.
7. Heat
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
SERVICING
1. Servicing
ATTENTION:
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
To mobile phone user:
Using a mobile phone in the vicinity of the VCR may cause
picture vibration on the TV screen or change the screen to a
blue back display.
On placing the VCR:
Some TVs generate strong magnetic fields.
● Make sure to place the VCR at least 20 cm (7 or 8 inches)
away from a TV.
● DO NOT place the VCR close to a TV as it may cause noise,
picture disturbance or malfunctions (power off, etc.) to occur.
— 3 —
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Other Functions.......................................................................... 17
Timer warning display.......................................................... 17
Checking tape position ........................................................ 17
Buttons, Connectors and Indicators ................................................ 5
Changing display information.............................................. 17
Function settings.................................................................. 17
Satellite Auto Recording ...................................................... 20
Child Lock........................................................................... 20
Connections and Plug&Play Setting ................................................ 7
Initial Settings.............................................................................. 8
Clock Setting .......................................................................... 8
Tuner Setting .......................................................................... 9
Multi-Brand Remote Control ....................................................... 21
TV Brand Setting.................................................................. 21
Cable Box or DBS Receiver Brand Setting............................ 21
Changing Remote Control Code .......................................... 22
Playback .................................................................................... 10
Basic Playback ..................................................................... 10
Playback Features................................................................. 11
Editing....................................................................................... 22
Editing with Another VCR.................................................... 22
Audio Dubbing.................................................................... 23
Insert Editing and AV Dubbing............................................. 24
Recording................................................................................... 12
Basic Recording ................................................................... 12
Recording Features............................................................... 12
Series Playback and Recording..................................................... 13
Series Playback..................................................................... 13
Series Recording................................................................... 14
Specifications............................................................................. 25
Index ........................................................................................ 26
List of Terms......................................................................... 26
Timer Recording.......................................................................... 15
Changing VCR Plus+® Setting................................................ 15
VCR Plus+® Timer Programing.............................................. 16
Troubleshooting ......................................................................... 27
Express Timer Programing .................................................... 16
24HR Quick Programing ...................................................... 16
Checking, Canceling or Changing Program Settings.............. 17
Program Overlap Warning Display....................................... 17
— 4 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Buttons, Connectors and Indicators
Front Panel
Cassette loading slot
Advanced
JOG dial
REW
FF
24HR QUICK
REC LINK PROGRAM
POWER
INSERT A.DUB
S-VIDEO
VIDEO/AUDIO input
connectors
S-VIDEO
input
connector
Remote
sensor
Display panel
Start Time/Mode
Lock indicator
Stop Time/Mode Lock indicator
TBC
S-VHS
VCR mode
indicator
indicator
indicator
Timer mode
indicator
Play indicator
Record indicator
REC LINK
indicator
Channel and auxiliary input/
Clock time
Counter/Remain display
Rear Panel
REMOTE OUT
AC power cord
REMOTE IN
CONTINUED ON NEXT PAGE
— 5 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
On-screen display
If you press OSD (OK) on the Remote when “ON SCREEN (REC)
and ON SCREEN (PLAY)” are set to “ON” (੬ pg. 18), you can see
the current VCR status on the TV screen.
The indications are not recorded even if the VCR is in the
recording mode.
VCR operation
mode
Channel and
auxiliary input
Timer warning display
Number keys
Day and
clock time
Tape speed
STEREO
program
indication
Cassette mark
Tape position
Index number
SAP
indication
Audio
monitor
indications
Tape
remaining time
Time counter
To recall an indication
A Press OSD (OK).
● All indications corresponding to the current status are
displayed for 5 seconds. After that, the counter
information and RECORD/PAUSE (if in the Record Pause
mode), remain on the TV screen.
B Press OSD (OK) again to clear the display.
● The RECORD/PAUSE indication remains on the TV screen.
* does not function with this VCR.
SEP function is available eventhough there is only indication of
SP/EP on the Remote.
The glow-in-the-dark buttons shown in white on the illustration
above are helpful when using the Remote in darkened rooms.
Buttons with a small dot on the left side of the name can also be
used to operate your TV while holding down TV on the Remote.
— 6 —
Download from Www.Somanuals.com. All Manuals Search And Download.
.
S-video Connection
Connections and Plug&Play
Setting
(allows you to make the most of the S-VHS picture performance.)
If your TV is equipped with a S-video input connector
A Perform “RF Connection” previously described.
B Connect the supplied S-video cable between the S-VIDEO
OUT connector on the rear of the VCR and the S-video input
connector on the TV.
A Check contents
Make sure the package contains all of the accessories listed in
“Specifications” (੬ pg. 25).
C Connect an audio cable between the AUDIO OUT connectors
on the rear of the VCR and the audio input connectors on the
TV.
B Situate VCR
Place the VCR on a stable, horizontal surface.
C Connect VCR to TV
The following connections are required.
D Perform Plug&Play setup
Plug the AC power cord into an AC outlet. DO NOT turn on the
VCR. The clock and tuner channels will be set automatically.
● The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS
channel in your area.
Antenna or cable
Coaxial cable
Flat feeder
During Initial Auto Clock Set
“Auto” blinks.
Matching transformer
(not supplied)
During Auto Channel Set
The channel numbers are displayed as they are
scanned and set.
Plug&Play Completed
The current time is displayed.
AC power cord
ATTENTION:
Depending on areas or reception conditions, the VCR may not
receive the Auto clock setting data from a PBS channel. If this
function is taking a considerable amount of time, it may be
necessary to perform the procedure in “Semiauto Clock Set”
(੬ pg. 8) or “Manual Clock Set” (੬ pg. 8).
What to do if Plug&Play setting failed
Back of VCR
AC outlet
● If an incorrect time is displayed on the display panel, perform
the procedure in “Semiauto Clock Set” (੬ pg. 8) or “Manual
Clock Set” (੬ pg. 8).
● If “– –:– –” appears on the display panel, ensure that the
antenna cable is connected correctly. Then turn on and off
the VCR; the Plug&Play setting will be automatically
reactivated.
To audio/video
input connectors
Audio/video
cable
(supplied)
● If Plug&Play setting is not performed though the antenna
cable is connected correctly, perform the procedure in
“Manual Clock Set” (੬ pg. 8) and “Auto Channel Set”
(੬ pg. 9) or “Manual Channel Set” (੬ pg. 9).
To 75 ⍀ terminal
RF cable
(supplied)
TV
E Set VCR channel
Press POWER 1 to turn off the VCR, then press STOP/EJECT
(0) on the VCR for more than 5 seconds. “3CH” appears on
the display panel. Press CH+/– on the Remote to select “3CH”,
“4CH” or “–CH”(OFF), then press OK.
To S-video input
connector
S-video cable
(supplied)
● The VCR channel is preset to “3CH”. Set to “4CH” if 3CH is
used for broadcasting in your area.
RF Connection
F Final preparation for use
Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or
AV mode) on the TV. You can now perform basic playback or
basic recording.
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the ANT. IN terminal on the
rear of the VCR.
C Connect the supplied RF cable between the TV OUT terminal
on the rear of the VCR and the TV’s antenna input terminal.
● If you connect the TV and the VCR only using the RF
connection, press TV/VCR on the Remote so that the VCR mode
indicator (
) lights on the display panel.
NOTES:
● The VCR channel is the channel on which you can watch the
picture from the VCR on the TV when only using the RF
connection.
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
A Connect the antenna, VCR and TV as shown in the illustration.
B Connect an audio/video cable between the AUDIO/VIDEO
OUT connectors on the rear of the VCR and the audio/video
input connectors on the TV.
● Even if you are using audio/video cables to connect your VCR to
your TV, you must also connect it using the RF cable. This will
ensure that you can record one show while watching another.
— 7 —
Download from Www.Somanuals.com. All Manuals Search And Download.
E Select D.S.T. mode
Initial Settings
Press OK or SHUTTLE PLUS e to move the highlight bar to
“D.S.T.”, then press SHUTTLE PLUS rt repeatedly until the
desired setting is selected.
Clock Setting
AUTO: Select if you want to adjust your VCR’s clock
automatically by the incoming signal from the host
channel. (Auto Daylight Saving Time enables automatic
adjustment of the VCR’s clock at the start and end of
Daylight Saving Time.) Be sure to select the correct time
zone manually in step 6.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
ON:
OFF:
Adjustment will be made by the built-in clock itself.
Select when Daylight Saving Time does not apply to you.
F Select time zone
Press OK or SHUTTLE PLUS e to move the highlight bar to
“TIME ZONE”, then press SHUTTLE PLUS rt repeatedly until
“AUTO” or the desired time zone is selected. Each time you press
the button, the time zone changes as follows:
{AUTO {ATLANTIC {EASTERN {CENTRAL
{MOUNTAIN {PACIFIC {ALASKA {HAWAII
{ (back to the beginning)
G Complete Semiauto Clock Set
Press MENU to return to normal screen.
Perform clock setting only if the clock has not been set correctly
by the Plug&Play setting.
IMPORTANT
Turn off the VCR. “Auto” will appear on the display panel while
the clock is being set. The current clock time will appear
automatically when the clock setting is complete.
Preparations
A Access Main Menu screen, then Initial
MAIN MENU
FUNCTION SET
Set screen
TUNER SET
INITIAL SET
Press MENU on the Remote. Press
Setting clock manually
— Manual Clock Set
SHUTTLE PLUS rt to move the
highlight bar (arrow) to “INITIAL SET”,
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
then press OK or SHUTTLE PLUS e.
First follow steps 1 to 2 in “Preparations” previously described,
then go to the following steps.
B Access Clock Set screen
Press SHUTTLE PLUS rt to move the
highlight bar (arrow) to “CLOCK SET”,
then press OK or SHUTTLE PLUS e.
INITIAL SET
CLOCK SET
GUIDE CHANNEL SET
C Set time, date and year
Press SHUTTLE PLUS rt until the
desired time appears, then press OK or
SHUTTLE PLUS e. Set the date and year
in the same way.
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
● Holding SHUTTLE PLUS rt changes
the time in 30-minute intervals, or
changes the date in 15-day intervals.
Setting clock semiautomatically
— Semiauto Clock Set
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually. First follow steps 1 to 2 in
“Preparations” above, then go to the following steps.
D Select D.S.T. mode
Press OK or SHUTTLE PLUS e to move
the highlight bar to “D.S.T.”, then press
SHUTTLE PLUS rt to select the desired
setting.
CLOCK SET
C Set Auto Clock to ON
TIME
DATE
YEAR
04
Press OK or SHUTTLE PLUS e on the
Remote repeatedly to move the highlight
bar to “AUTO CLOCK”, then press
SHUTTLE PLUS rt so that “ON” is
selected.
– –:– – AM 1/ 1
AUTO CLOCK : ON
ON: Adjustment will be made by the
built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
HOST CH
D.S.T.
TIME ZONE : AUTO
: AUTO
: AUTO
(CATV)
PRESS (
,
), THEN (OK)
PRESS (MENU) TO END
E Start clock
Press MENU and normal screen appears.
● The time set previously will be erased
when “AUTO CLOCK”, “HOST CH”, “D.S.T.” or “TIME ZONE”
setting is changed.
To make corrections any time during the process
Press OK or SHUTTLE PLUS e repeatedly until the item you
D Select host channel
want to change blinks, then press SHUTTLE PLUS rt.
You can either select “AUTO” or enter a PBS channel number.
Press OK or SHUTTLE PLUS e to move the highlight bar to
“HOST CH”, then press SHUTTLE PLUS rt repeatedly until
“AUTO” or the desired PBS channel number is selected.
● Some PBS channels do not transmit clock setting data.
— 8 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting channels manually
— Manual Channel Set
Tuner Setting
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
You can add the channels you want or delete the channels you do
not want manually.
A Access Main Menu screen, then Tuner
Set screen
Press MENU on the Remote. Press
SHUTTLE PLUS rt to move the
highlight bar (arrow) to “TUNER SET”, then
press OK or SHUTTLE PLUS e.
B Access Manual Channel Set screen
Number keys
Press SHUTTLE PLUS rt to move the
highlight bar (arrow) to “MANUAL
CHANNEL SET”, then press OK or
SHUTTLE PLUS e.
C Add or skip desired channels
To add channels
A Press the Number keys on the Remote
to input a channel number you want to
add.
B Press OK or SHUTTLE PLUS e to set to “ADD”.
C Repeat A to B to add other channels.
To skip channels
A Press SHUTTLE PLUS rt or the Number keys to select a
channel number you want to skip.
B Press OK or SHUTTLE PLUS e to set to “SKIP”.
C Repeat A and B to skip other channels.
D Press MENU to return to normal screen
Setting channels automatically
— Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
A Access Main Menu screen, then Tuner
Set screen
Press MENU on the Remote. Press
SHUTTLE PLUS rt to move the
highlight bar (arrow) to “TUNER SET”, then
press OK or SHUTTLE PLUS e.
B Perform Auto Channel Set
Press SHUTTLE PLUS rt to move the
highlight bar (arrow) to “AUTO CHANNEL
SET”, then press OK or SHUTTLE PLUS
e. The VCR selects the correct band (TV or
CATV) automatically during Auto Channel
Set.
● When Auto Channel Set is complete,
“SCAN COMPLETED” appears on
screen.
● If the scan was unsuccessful, “SCAN
COMPLETED–NO SIGNAL–” appears on
❚ ❚ ❚ – – – – – – – – – – – – – – –
screen. Check the connections and start
again.
C Press MENU to return to normal screen.
— 9 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
e
w
i
N
s
e
o
i
t
s
m
P
l
a
t
y
l
Basic Playback
(
Turn on the VCR and TV, and select the VCR channel (or AV mode).
p
A Load a cassette
REW
FF
Make sure the window side
is up, the rear label side is
facing you and the arrow on
the front of the cassette is
pointing towards the VCR.
24HR QUICK
REC LINK PROGRAM
POWER
INSERT A.DUB
S-VIDEO
● Do not apply too much pressure when inserting.
● The VCR turns on, and the counter on the on-screen display is
reset, automatically.
● If the cassette’s record safety tab has been removed and “REC
SAFETY” is set to “ON” (੬ pg. 19), playback begins
automatically.
Forward
Reverse
Reverse
slow
Reverse
search
Normal
play
Reverse
play
Slow
Forward search
motion
B Start playback
Press PLAY (4).
● The S-VHS indicator lights up when you play back a tape
recorded in S-VHS mode or in S-VHS ET mode (੬ pg. 13).
● If “VIDEO CALIBRATION” is set to ”ON” (੬ pg. 18), “VIDEO
CALIBRATION” appears on the screen, and this VCR checks the
tape condition during automatic tracking.
motion
SP -7 -5 -3
EP -21 -11 -5
SEP -21 -11 -7
-1
-1
-
-1/6 1/6 1/2
-1/6 1/6 1/2
1
1
1
1.5
1.5
-
2
2
-
3
5
7
5
7
11 21
11 21
-
-
-
● You can hear the (normal) audio track only during 1.5x PB
speed search.
During playback
Stop playback
● 1.5x PB speed is only for SP/EP mode.
When the tape is not running
Rewind/fast-forward
Press STOP (8) on the
Remote.
OR Press STOP/EJECT (0) on
the VCR.
Pause playback and view still picture
Press PAUSE (9).
Press REW (3 ) or FF
(5).
OR Turn the JOG dial to the left
or right.
Eject the cassette
● Press PLAY (4) to resume normal playback.
NOTE:
Press STOP/EJECT (0).
● You can also eject the cassette when the VCR is turned off.
During still picture, vertical vibration may appear on the TV
screen. Press CH+/– on the Remote to get a clearer picture.
Turn off the VCR
Pause and Frame-by-Frame playback
Press POWER 1.
Press PAUSE (9) to pause, then press SHUTTLE PLUS 2 or
6 (or PAUSE (9)) repeatedly, or turn the JOG dial to the left or
right.
To prohibit operations during playback (Mode Lock)
Press and hold OK on the Remote for more than 5 seconds.
● Press PLAY (4) to resume normal playback.
“
” and “ ” light up on the front display panel. The
Picture Search
playback will not be interrupted until the recording end
(unrecorded portion) or tape end is reached.
To resume the other operations, press and hold OK on the
Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen display
appears and the time counter remains on the TV screen. If the
time counter is not necessary, set “ON SCREEN (PLAY)” to
“OFF” (੬ pg. 18).
Press REW (3 ) or FF (5) on the Remote. Press REW (3 )
or FF (5) again to perform high-speed search.
● Each time you press REW (3 ) or FF (5) the search speed
changes between low-speed and high-speed.
● Press PLAY (4) to resume normal playback.
Variable-Speed Picture Search (including slow-motion)
Press SHUTTLE PLUS 2
or 6 repeatedly.
OR Turn the JOG dial to the left
or right.
● Press PLAY (4) to resume normal playback.
● Each time you press SHUTTLE PLUS 2 or 6 or each time
JOG dial passes a click position, the playback speed changes.
To decrease the speed during picture search, press the opposite
direction button repeatedly or turn the dial in the opposite
direction.
● During still picture, press and hold SHUTTLE PLUS 6 to
start forward (or SHUTTLE PLUS 2 to start reverse) slow
motion playback. When you release the button, still picture
resumes. During still picture, holding PAUSE (9) for more than
2 seconds also starts forward slow motion playback. If you
press PAUSE (9) again, still picture resumes.
NOTE:
During slow motion, some noise may appear on the TV screen.
Press CH+/– on the Remote to eliminate the noise.
— 10 —
Download from Www.Somanuals.com. All Manuals Search And Download.
● To select the returning point (recording end or tape end), see
“REC END RETURN” on ੬ page 19.
Playback Features
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
To prohibit operations during Repeat Play (Mode Lock)
Press and hold OK on the Remote for more than 5 seconds.
“
” and “ ” light up on the front display panel. The entire
recording or entire tape will be played back repeatedly without
any interruption.
To cancel Mode Lock, press and hold OK on the Remote again
for more than 5 seconds.
Adjusting tracking condition
— Tracking Adjustment
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic tracking
starts working and continuously analyzes the signal to enable
optimum picture quality during playback.
● When OK is pressed to set Mode Lock, the on-screen display
appears and the time counter remains on the TV screen. If the
time counter is not necessary, set “ON SCREEN (PLAY)” to
“OFF” (੬ pg. 18).
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, follow the procedures below.
Locating beginning of recordings
— Index Search
On the Remote
A Press SP/EP during playback to activate manual tracking.
Index codes are placed on the tape at the beginning of each
recording when recording on this VCR.
B Press CH +/– to eliminate the noises. Press it briefly for a fine
adjustment, or press and hold for a coarse adjustment.
● Press SP/EP again to reactivate automatic tracking.
A While the tape is not running, press SHUTTLE PLUS
2
or
6
on the Remote to start search.
B
To access a recording of 2 to 9 index
codes away, press or repeatedly
Selecting monitor sound
— Audio Monitor
2
6
until the correct number is displayed on
the screen (only if “ON SCREEN (REC)” is
While playing back a tape on which stereo sound or SAP sound is
recorded, press A.MONITOR on the Remote. Each time you press
the button, sound changes.
set to “ON” (
੬
pg. 18)). Playback begins
automatically when the desired recording
is located.
Beginning of the
current program
recorded
Beginning of the
2nd next program
recorded
Current
position on
the tape
HI-FI
HI-FI L
HI-FI R
NORM
NORM
HI-FI
HI-FI: Normally select this. Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM: Sound on the normal track is played back.
NORM HI-FI: Both sounds on the Hi-Fi track and normal track are
mixed and played back.
Previous
program
recorded
Next
program
recorded
2nd next
NOTES:
Locating beginning of timer recordings
— Instant Review
● The above indication appears when “ON SCREEN (PLAY)” is set
to “ON” (੬ pg. 18), though the monitor sound changes in
sequence.
After ensuring that the VCR is turned off and that the timer mode is
disengaged, press REVIEW.
● If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
● If RF connection (੬ pg. 7) is used for viewing pictures on the
TV, sound will be monaural even though you select “Hi-Fi”.
● You can also use the menu to select your desired monitor sound.
(੬ pg. 19)
● The VCR turns on, and rewinds to the index code indicating the
beginning of the last timer-recorded program, then begins
playback automatically.
● You can access a program of 2 to 9 index codes away from the
current position on the tape. If, for example, you have
5 programs recorded and you want to watch the third one, press
REVIEW three times.
Automatic operations after rewinding
— Next Function Memory
● The Instant Review function will also operate if the VCR is
turned on.
The Next Function Memory “tells” the VCR what to do after
rewinding is complete. Ensure that the VCR is in stop mode.
Skipping unwanted portions
— Skip Search
On the Remote
● For Automatic Playback Start
Press REW (3), then press PLAY (4) within 2 seconds.
Press SKIP SEARCH on the Remote once to 4 times during
playback. Each press initiates a 30-second period of high speed
playback (up to 2 minutes). When the specified portion of the tape
is skipped, normal playback resumes automatically. To return to
normal playback during Skip Search, press PLAY (4).
● For Automatic Power Off
Press REW (3), then press POWER 1 within 2 seconds.
● For Automatic Timer Standby
Press REW (3), then press TIMER within 2 seconds.
NOTE:
Playback Resume Function
It is not possible to select the Automatic Timer Standby function if
the cassette’s record safety tab is removed.
If there is a power outage during normal playback (or Series
Playback), the playback will resume automatically when the
power is restored to the VCR. (No setting is required for this
function.)
Playing back tape repeatedly
— Repeat Play
During playback, press and hold PLAY (4) for more than
5 seconds. The play indicator ($) on the display panel starts
blinking slowly. To stop playback, press STOP (8) on the Remote
or STOP/EJECT (0) on the VCR.
— 11 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Features
Recording
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab and set “REC SAFETY” to
“ON” (੬ pg. 19). To record on it later,
cover the hole with adhesive tape and
reset the “REC SAFETY” to “OFF” (੬ pg. 19).
Recording on one tape repeatedly
— Repeat Recording
Record safety tab
You can record programs on one tape repeatedly.
While recording, press and hold PLAY (4) and REC (7) on the
Remote or REC (7) on the front panel for more than 5 seconds.
The record indicator on the front display panel starts blinking
slowly.
Basic Recording
To stop recording, press STOP (8) on the Remote or STOP/EJECT
(0) on the front panel.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
To prohibit operations during Recording or Repeat Recording
(Mode Lock)
Press and hold OK on the Remote for more than 5 seconds.
A Load a cassette
Make sure the record safety tab is intact. If not, set “REC SAFETY”
to “OFF” (੬ pg. 19) or cover the hole with adhesive tape before
inserting the cassette.
● The VCR turns on, and the counter on the on-screen display is
reset, automatically.
“
” and “ ” light up on the front display panel. No button
will function and recording will not be interrupted.
To resume the other operations, press and hold OK on the
Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen display
appears and the time counter remains on the TV screen. If the
time counter is not necessary, set “ON SCREEN (REC)” to
“OFF” (੬ pg. 18).
B Select recording channel
Press CH+/– or the Number keys on the Remote. Or push the JOG
dial, then turn it to the left or right.
● If you connect the TV and the VCR only using the RF
connection (੬ pg. 7), press TV/VCR on the Remote so that the
VCR mode indicator ( ) lights on the display panel, to view
the program to be recorded.
Watching one program while recording another
During recording...
● If you connect the TV and the VCR only using the RF
connection (੬ pg. 7) to view pictures from the VCR, press TV/
VCR on the Remote so that VCR mode indicator ( ) goes off
from the display panel. (The TV broadcast being recorded
disappears.)
● If you are using the AV connection (੬ pg. 7) to view pictures
from the VCR, change the TV’s input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
C Set tape speed
Press SP/EP. The selected tape speed will appear on the TV screen.
NOTES:
● When you record using SEP mode, playback the tape with this
deck.
● You can select tape speed in the stop mode or during recording
pause mode.
Second Audio Recording
D Start recording
On the VCR, press REC (7). Or on the Remote, while holding REC
This VCR’s built-in MTS decoder enables reception of
Multichannel TV Sound broadcast. To record a SAP program
received, set “2ND AUDIO RECORD” to “ON” (੬ pg. 19).
(7), press PLAY (4).
NOTE:
If “VIDEO CALIBRATION” is set to “ON” (੬ pg. 18) (default
setting), the VCR takes about 7 seconds to assess the quality of the
tape in use, then recording begins with the picture level
optimized.
NOTES:
When the channel is changed on the VCR;
● The ‘STEREO” indication appears on the screen for about 5
seconds if the program is stereo broadcast.
● The “SAP” indication appears on the screen for about 5 seconds
if the program is a SAP broadcast.
During recording
Pause recording
● Both indications appear when a stereo program is accompanied
by SAP sound.
Press PAUSE (9).
● Press PLAY (4) to resume recording.
● You can select channel in the recording pause mode.
Recording Resume Function
If there is a power outage during recording (or Timer Recording or
Series Recording), the recording will resume automatically when
the power is restored to the VCR. (No setting is required for this
function.)
Stop recording
Press STOP (8) on the
Remote.
OR Press STOP/EJECT (0) on
the VCR.
NOTE:
If the tape reaches its end during recording, the recording stops
and “⅜” and “$” on the display panel blink. Press STOP/EJECT
(0) on the VCR to eject the cassette or press REW (3) on the
Remote to rewind the tape.
— 12 —
Download from Www.Somanuals.com. All Manuals Search And Download.
S-VHS (Super VHS), S-VHS ET or VHS Recording
Mode
Series Playback and Recording
This VCR can record in S-VHS (Super VHS), S-VHS ET or VHS.
● To record in S-VHS:
Series Playback
Set “S-VHS MODE” to “ON” (੬ pg. 19). Then, insert a cassette
marked “S-VHS”. The S-VHS indicator lights up on the display
panel.
The S-VHS recording mode is selected.
● To record in S-VHS ET on a VHS cassette:
Set “S-VHS ET” to “ON” (੬ pg. 19). Then, insert a cassette
marked “VHS”. The S-VHS indicator lights up on the display
panel.
To REMOTE OUT
To REMOTE IN
To
SR-V101US-1
To S VIDEO OUT
AUDIO/
VIDEO OUT
● To record in VHS:
Audio/Video
Cable
Insert a cassette marked “VHS”.
Set “S-VHS ET” to “OFF” (੬ pg. 19).
● To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up
on the display panel. Then, set “S-VHS MODE” to “OFF”
(੬ pg. 19). The S-VHS indicator goes off.
The VHS recording mode is selected.
(Supplied)
S-Video Cable
(Supplied)
Mini-plug
Mini-plug
cable
cable
To
(Not supplied)
(Not
AUDIO/
supplied)
To S VIDEO IN
VIDEO IN
To
NOTE:
REMOTE OUT
When playing back a tape that has been recorded in S-VHS or
S-VHS ET, the S-VHS indicator lights up on the display panel
regardless of the “S-VHS ET” (੬ pg. 19) or “S-VHS MODE”
(੬ pg. 19) setting.
To REMOTE IN
SR-V101US-2
To
AUDIO/
VIDEO OUT
Audio/Video Cable (Supplied)
To S VIDEO OUT
To
Audio/Video Input
S-Video Cable (Supplied)
To S-Video Input
NOTE:
Series Playback is also possible using the front AUDIO/VIDEO
connectors.
REW
FF
24HR QUICK
PROGRAM
REC LINK
POWER
INSERT A.DUB
S-VIDEO
Using two sets (or more) of SR-V101US, you can play back two (or
more) cassettes alternately as many times as you want. You can
select the returning point for Series Playback (੬ pg. 19).
Use the buttons and controls on the VCR’s front panel for the
Series Playback operations (except when using Mode Lock).
CONTINUED ON NEXT PAGE
— 13 —
Download from Www.Somanuals.com. All Manuals Search And Download.
A Make connections
Connect two sets of SR-V101US and a TV using AV cables as
shown in the illustration.
Series Recording
● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5
mm mini-plug connector.
or
Another VCR
Camcorder
● When playing back S-VHS recordings, it is recommended to use
the S-VIDEO connection to minimize picture degradation.
To S Video
Output
To Audio/Video Output
Audio/Video Cable (Not supplied)
B Turn on all components
After completing the connections, turn on all the components.
● Set the TV to video input mode or A/V input mode. Refer to the
TV instruction manual.
S-Video Cable (Not supplied)
To S VIDEO IN
To AUDIO/VIDEO IN
C Load cassettes
Insert the playback cassette into each SR-V101US.
Set SR-V101US-2 to “AUX”. Press CH + or – to select the input
mode depending on the connector being used:
To REMOTE OUT
To REMOTE IN
● “L-1” for the rear AUDIO/VIDEO IN connector, or
● “F-1” for the front AUDIO/VIDEO input connector.
To
AUDIO/
VIDEO OUT
SR-V101US-1
To S VIDEO OUT
Audio/Video
Cable
D Start playback
(Supplied)
S-Video Cable
(Supplied)
● Press PLAY ( 4) on either of SR-V101US. When the playback
reaches to the returning point (tape end or recording end ੬
page 19), the other SR-V101US successively starts to play. (The
cassette will automatically be rewound when the playback
stops.) Therefore, the cassettes loaded on two SR-V101US will
be played back alternately as many times as you want.
Mini-plug
Mini-plug
cable
(Not
supplied)
cable
To
(Not supplied)
AUDIO/
To S VIDEO IN
VIDEO IN
To
REMOTE OUT
To stop playback
Press STOP/EJECT (0) on the SR-V101US which is playing
To REMOTE IN
back a cassette.
SR-V101US-2
To
AUDIO/
NOTE:
VIDEO OUT
If there is a power outage during Series Playback, the playback
will resume automatically when the power is restored to the VCR.
(No setting is required for this function.)
Audio/Video Cable (Supplied)
To S VIDEO OUT
To
Audio/Video Input
To prohibit operations during Series Playback (Mode Lock)
Press and hold OK on the Remote for more than 5 seconds.
S-Video Cable (Supplied)
To S-Video Input
“
” and “ ” light up on the front display panel. The 2
cassettes will be played back alternately without any
interruption.
To resume the other operations, press and hold OK on the
Remote again for more than 5 seconds.
● When OK is pressed to set Mode Lock, the on-screen display
appears and the time counter remains on the TV screen. If the
time counter is not necessary, set “ON SCREEN (PLAY)” to
“OFF” (੬ pg. 18).
NOTE:
Select the correct input mode (“L-1” for the rear connector, “F-1”
for the front connector). (੬step 3)
REW
FF
24HR QUICK
PROGRAM
REC LINK
POWER
INSERT A.DUB
S-VIDEO
Using two sets (or more) of SR-V101US, a long recording will be
possible (such as camcorder recording, another VCR playback or
TV broadcast).
Use the buttons and controls on the VCR's front panel for the
Series Recording operations (except when using Mode Lock).
— 14 —
Download from Www.Somanuals.com. All Manuals Search And Download.
A Make connections
Connect two sets of SR-V101US to other equipment, antenna or
cable as shown in the illustration.
Timer Recording
● The mini-plug cable is a mono 3.5 mm mini-plug to mono 3.5
mm mini-plug connector.
● When connecting a camcorder or another VCR with an
S-VIDEO output connector as recording source, it is
recommended to use the S-VIDEO connection to minimize
picture degradation.
Up to 8 timer recording programs can be made using VCR Plus+
timer programing, Express timer programing or 24HR Quick
Programing method as far as a year in advance. Remember, the
clock must be set before you can program the timer.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
B Turn on all components
After completing the connections, turn on all the components.
● Set the TV to video input mode or A/V input mode. Refer to the
TV instruction manual.
NOTES:
● If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
C Set recording VCR's input mode
Set to “AUX“. Press CH + or – to select the input mode depending
on the connector being used:
● “L-1“ for the rear AUDIO/VIDEO IN connector, or
● “F-1“ for the front AUDIO/VIDEO input connector.
● After timer recording is completed, the VCR turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● In case of a power failure after programming, the VCR’s memory
backup keeps your selections (if the lithium battery is not
exhausted).
● If the tape reaches its end during timer recording, the recording
stops and “ #“, “ ⅜” and “$” on the display panel blink. Press
TIMER to disengage timer, then press STOP/EJECT (0) on
the VCR to eject the cassette or press POWER 1 then press
REW (3) on the Remote to rewind the tape.
D Prepare for recording
Insert the recording cassette into each SR-V101US, and prepare
the playback source.
NOTE:
If you do not want to display the superimposed indication on the
screen during recording, set “ON SCREEN (REC)“ to “OFF“
(੬ pg. 18). If the playback equipment has a superimpose/OSD
disable feature, set its superimpose or display feature to “OFF“ as
well.
®
Changing VCR Plus+ Setting
The VCR Plus+ programing system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
E Start recording
Press REC (7) on either of SR-V101US. When the tape remaining
time reaches to 2 minutes while recording, the other SR-V101US
successively starts to record. Therefore, recording will be
continued onto cassettes loaded on two SR-V101US alternately.
● The cassette will automatically be rewound when the recording
stops.
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the VCR Plus+ “Guide Channel Set” for each
station.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the following steps to
set the correct guide channel number.
● Replace the cassette after rewound if you want to continue to
record onto another cassette.
To stop recording
Press STOP/EJECT (0) on the SR-V101US which is recording.
A Access Main Menu screen, then Initial Set screen
Press MENU on the Remote. Press SHUTTLE PLUS rt to move
the highlight bar (arrow) to “INITIAL SET”, then press OK or
SHUTTLE PLUS e.
To prohibit operations during Series Recording (Mode Lock)
Press and hold OK on the Remote for more than 5 seconds.
“
” and “
” light up on the front display panel. The picture
will be recorded onto the cassettes alternately without any
interruption.
To resume the other operations, press and hold OK on the
Remote again for more than 5 seconds.
B Access Guide Channel Set screen
Press SHUTTLE PLUS rt to move the highlight bar (arrow) to
“GUIDE CHANNEL SET”, then press OK or SHUTTLE PLUS e.
● When OK is pressed to set Mode Lock, the on-screen display
appears and the time counter will be recorded with your
picture. If the time counter is not necessary, set “ON SCREEN
(REC)” to “OFF” (੬ pg. 18).
GUIDE CHANNEL SET
C Input guide channel number
GUIDE CH :
VCR CH
6
Press SHUTTLE PLUS rt or the Number
keys to select the VCR Plus+ guide channel
number as shown in the TV listing, then
press OK or SHUTTLE PLUS e.
:
– – –
PRESS NUMBER KEY (0–9)
OR (
,
), THEN (OK)
NOTES:
PRESS (MENU) TO END
● Series Recording is also possible using the front AUDIO/ VIDEO
connectors.
GUIDE CHANNEL SET
D Input receiving channel number
GUIDE CH :
VCR CH
6
47
Press SHUTTLE PLUS rt or the Number
keys to select the number of the channel
on which the guide channel’s broadcasts
are received, then press OK or SHUTTLE
PLUS e.
● When recording a TV broadcast, tune in the same channel on
both SR-V101US.
:
● If you do not want to record the operational indications on the
screen during Series Recording, set both “ON SCREEN (PLAY)”
and “ON SCREEN (REC)” to “OFF”. (੬ pg. 18)
● If there is a power outage during Series Recording, the recording
will resume automatically when the power is restored to the
VCR. (No setting is required for this function.)
PRESS NUMBER KEY (0–9)
OR ( ), THEN (OK)
PRESS (MENU) TO END
,
● Repeat steps 3 and 4 for each instance.
E Return to normal screen
Press MENU on the Remote.
CONTINUED ON NEXT PAGE
— 15 —
Download from Www.Somanuals.com. All Manuals Search And Download.
®
● To set the tape speed, press SP/EP.
● To timer-record daily (Sunday–
Saturday) or weekly serials, press
DAILY (Number key “8”) or WEEKLY
(Number key “9”). Pressing the
button again makes the “DAILY” or
“WEEKLY” display disappear.
VCR Plus+ Timer Programing
PROGRAM 1
The PlusCode programing numbers are
the numbers next to the program in
most TV listing.
Load a cassette with the record safety
tab intact. If not, set “REC SAFETY” to
“OFF” (੬ pg. 19). The VCR turns on,
and the counter is reset, automatically.
START
8:00AM
DATE
STOP
9:00AM
CH
12/24/04
FRI
110 SP
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
C Press OK or PROG..
● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, see “Program Overlap Warning Display”
(੬ pg. 17).
A PressPROG. ontheRemotetoaccess
the PlusCode No. screen.
PLUSCODE NO.
D Press TIMER. The VCR turns off automatically and “#” is
displayed on the display panel.
PRESS NUMBER KEY (0–9)
PRESS (+/–) TO SET
EXPRESS PROGRAMMING
24HR Quick Programing
PRESS (PROG.) TO END
VCR PLUS+ SYSTEM
You can program a timer recording that starts within 24 hours
using the JOG dial on the VCR.
B Press the appropriate Number keys
Load a cassette with the record safety tab intact or set “REC
SAFETY” to “OFF” (੬ pg. 19). The VCR turns on, and the counter
is reset, automatically.
to input the PlusCode number, then
press OK or SHUTTLE PLUS e. Check to make sure the
setting is accurate on the Program screen.
A Press 24HR QUICK PROGRAM on the
PROGRAM 1
PLUSCODE NO.
1 2 3 4 5 6 7 8
(PLUSCODE NO. 12345678)
VCR. The start time indicator (
blinking on the display panel.
) starts
START
8:00PM
DATE
STOP
10:00PM
CH
12/24/04
FRI
12 SP
Start time
Stop time
B Turn the JOG dial to the left or right to set
the start time.
PRESS NUMBER KEY (0–9)
THEN (OK)
PRESS (PROG.) TO END
VCR PLUS+ SYSTEM
PRESS (8=DAILY, 9=WEEKLY
STOP+/– = STOP TIME, SP/EP)
PRESS (PROG.) TO END
● One click stop of the JOG dial changes
the time in 5-minute intervals.
● If the Guide Channel Set screen
appears after pressing OK, press the
Number keys, CH+/– or SHUTTLE
PLUS rt to input the number of the
channel on which the broadcast for
the PlusCode number is received on
the VCR, then press OK.
GUIDE CHANNEL SET
GUIDE CH : 12
C Push the JOG dial. The stop time
VCR CH
:
– – –
indicator (
) starts blinking on the
display panel. Turn the JOG dial to the
left or right to set the stop time.
PRESS NUMBER KEY (0–9)
OR ( ), THEN (OK)
PRESS (PROG.) TO END
,
Channel number
D Push the JOG dial. Turn the JOG dial to
the left or right to select the channel.
● To set the tape speed, press SP/EP. The
● To set the tape speed, press SP/EP.
● To change the stop time, press STOP+/–.
current setting for the tape speed appears on the display
panel for about 5 seconds. Press SP/EP again to change the
setting while tape speed is displayed.
● To timer-record daily (Sunday–Saturday) or weekly serials,
press DAILY (Number key “8”) or WEEKLY (Number key
“9”). Pressing the button again makes the “DAILY” or
“WEEKLY” display disappear.
● If you made a mistake, press CANCEL to access the PlusCode
No. screen again.
E To engage timer recording standby mode, press 24HR QUICK
PROGRAM. The VCR turns off automatically and “#” is
displayed on the display panel.
● If an incorrect PlusCode number or the one for a broadcast
already finished has been input, “ERROR” is displayed for
about 5 seconds, then the PlusCode No. screen reappears.
NOTES:
● If “Err” appears on the display panel, repeat the above steps
again.
● When a menu screen is shown, you cannot use 24HR Quick
Programing function. Press MENU to return to normal screen,
and try again.
● You can use 24HR Quick Programing function also when the
VCR is turned off.
● For 24HR Quick Programing function, the program overlap
warning display does not appear even if some programs overlap
each other.
C Press OK or PROG..
● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, see “Program Overlap Warning Display”
(੬ pg. 17).
D Press TIMER. The VCR turns off automatically and “#” is
displayed on the display panel.
Express Timer Programing
Load a cassette with the record safety tab intact. If not, set “REC
SAFETY” to “OFF” (੬ pg. 19). The VCR turns on, and the counter
is reset, automatically.
To use the VCR while it is in timer recording standby
mode
Press TIMER, then press POWER 1. After you use the VCR, press
A Press PROG. on the Remote to access the PlusCode No. screen.
TIMER again to put the VCR into timer recording standby mode.
B Press START+/– once to access
PROGRAM 1
Program screen.
START
– –:– –AM
DATE
STOP
– –:– –AM
CH
Press START+/–, STOP+/–, DATE+/– or
CH+/– repeatedly to enter the start
time, stop time, date or channel.
● Press and hold START+/– or STOP+/–
to increase the time in 30-minute
intervals.
– –/– –/– –
– – – SP
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
— 16 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking, Canceling or Changing Program
Settings
A Disengage timer
Press TIMER, then press POWER 1.
● When “AUTO TIMER” is set to “ON” (੬ pg. 18), you do not
have to press TIMER.
Other Functions
Timer warning display
–WARNING–
TIMER RECORDING
TO START SOON
(CANCEL)
A warning appears on the TV screen to tell
you that the timer-recording is to start in
5 minutes if you are not in the timer
recording standby mode at that time. Press
TIMER to put the VCR into timer recording
standby mode. To clear the display, press CANCEL on the Remote.
B Access Program Check screen
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
Press PROG. CHECK.
11:30P
1:00 125 12/25
C Access Program screen
Press PROG. CHECK again. Each time you
press PROG. CHECK, the next program’s
Program screen appears.
Checking tape position
PRESS (CHECK) TO NEXT
When you change the VCR operation
mode from the stop mode to fast forward
+
+
+
E
or rewind mode, or when you perform an
Index Search (੬ pg. 11) or Instant Review
(੬ pg. 11), the tape position indicator
appears.
The position of “q” in relation to “B” (Beginning) or “E” (End)
shows you where you are on the tape.
B
D Cancel or change program setting
To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START+/–,
STOP+/–, DATE+/–, CH+/–, DAILY (Number key “8”), WEEKLY
(Number key “9”), and/or SP/EP when the Program screen on
which you want to make changes is shown.
REMAIN
COUNT
1:00
1:23:45
–
● Set “ON SCREEN (REC) and ON SCREEN (PLAY)” to “ON”
(੬ pg. 18).
E Return to normal screen
Press PROG. CHECK repeatedly until no Program screen is
Changing display information
patterns of information according to “REC/STOP” or “PLAY”.
shown.
When you press DISPLAY, the display panel shows the different
F Reengage timer recording standby mode
Press TIMER. The VCR turns off automatically and “#” is
displayed on the display panel.
● When “AUTO TIMER” is set to “ON” (੬ pg. 18), the timer
recording standby mode automatically resumes when you turn
off the VCR.
Time Counter
Clock Time
Tape Remaining Time
Channel No.*
* during stop, recording or recording pause only.
Program Overlap Warning Display
When “ON SCREEN (REC) and ON SCREEN (PLAY)” is set to
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
conflicting programs will start blinking.
“ON” (੬ pg. 18) and OSD (OK) on the Remote is pressed, time
counter and tape remaining time will appear on the TV screen. To
reset the time counter, press C.RESET on the Remote.
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00A 10:00
10:00A 10:45
11:30A 13:00
3
2
1
DAILY
12/25
12/25
Function settings
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
9:00A 10:00 92 12/26
You can use the other useful function settings on the Function Set
screen.
MAIN MENU
A Access Main Menu screen, then
(
,
) THEN (
)
(PROG.) : END
FUNCTION SET
Function Set screen
Example:
TUNER SET
INITIAL SET
Program 1 (you have just made) and Program 4 overlap each other
Press MENU on the Remote. Press
SHUTTLE PLUS rt to move the
A Select program to modify
PR START STOP CH DATE
highlight bar (arrow) to “FUNCTION SET”,
PRESS (
,
), THEN (OK)
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24
10:00A 10:45 40 12/25
PRESS (MENU) TO END
Press SHUTTLE PLUS rt, then press OK
or SHUTTLE PLUS e.
then press OK or SHUTTLE PLUS e.
11:30P
1:00 125 12/25
9:00P 10:00 10 12/24
B Select Function
● You can only select one of the
overlapping programs.
Press SHUTTLE PLUS rt to move the highlight bar (arrow) to
the function you want to set.
● If you do not mind this overlap, press
PROG. to finish the timer program
setting. The program starting earlier or program with the lower
program number will be recorded.
(
,
) THEN (
)
(PROG.) : END
PREVIOUS PAGE
AUTO SP EP TIMER
DIGITAL R3
PREVIOUS PAGE
FRONT AUX INPUT
REAR AUX INPUT
S-VHS ET
FUNCTION
DIGITAL TBC/NR
OFF
ON
OFF
OFF
HI-FI
ON
VIDEO
VIDEO
OFF
ON
ON
VIDEO CALIBRATION
PICTURE CONTROL
AUTO TIMER
AUTO
OFF
ON
VIDEO STABILIZER
2ND AUDIO RECORD
AUDIO MONITOR
S-VHS MODE
REC END RETURN
DAY/TIME INSERT
REC SAFETY
OFF
OFF
ON SCREEN (REC)
ON SCREEN (PLAY)
NEXT PAGE
PROGRAM 4
B Cancel or change program setting
To cancel a program, press CANCEL when
the Program screen you do not want is
shown.
To change a program, press the
appropriate button: START+/–, STOP+/–,
DATE+/–, CH+/–, DAILY (Number key
ON
ON
NEXT PAGE
DAILY T.RECORD
NORM
START
9:00PM
DATE
12/24/04
FRI
STOP
10:00PM
CH
SELECT WITH (
PRESS (MENU) TO END
,
) AND (OK)
SELECT WITH (
,
) AND (OK)
SELECT WITH (
,
) AND (OK)
PRESS (MENU) TO END
PRESS (MENU) TO END
10 SP
C Change setting
PRESS (CANCEL) TO CANCEL
PRESS (OK) TO CONFIRM
PRESS (PROG.) TO END
Press OK or SHUTTLE PLUS e. The default setting is bold in the
table below. Press MENU to return to normal screen.
“8”), WEEKLY (Number key “9”) and/or SP/EP when the Program
screen on which you want to make changes is shown, then press
OK or SHUTTLE PLUS e.
● If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
CONTINUED ON NEXT PAGE
— 17 —
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Ⅵ DIGITAL TBC/NR — ON/OFF
The setting you have made is kept in memory. Even if the VCR is
unplugged or the power failure occurs, it will resume every time
you turn on the VCR.
Your VCR is equipped with a Digital TBC (Time Base Corrector)
that removes jitter from fluctuating video signals to deliver a stable
picture even with old tapes and rental cassettes. The on/off of
Digital — DNR (Noise Reduction) which cuts noise and enables
clear picture reproduction is also linked to this function. It is
recommended to use the Digital TBC feature when playing back a
tape recorded on a camcorder, playing back a tape repeatedly
used and using this video recorder as the player for editing.
Ⅵ ON SCREEN (PLAY) — ON/OFF
When this function is set to “ON”, if you press OSD (OK)
(੬ pg. 6) various VCR status information (on-screen display)
appears on the screen during playback.
NOTES:
NOTES:
● If you play back a tape recorded under poor TV reception
condition, there may be cases where the picture becomes more
stable with DIGITAL TBC/NR set to OFF.
● When you use this VCR as the playback VCR for editing a tape,
be sure to set this function to “OFF”; otherwise, the VCR status
information (on-screen display) will be recorded on the edited
tape.
● When DIGITAL TBC/NR is set to ON, if you play back a tape
where certain types of signals are recorded (using PC or some
character generators), the playback picture may be distorted. If
this the case, set DIGITAL TBC/NR to OFF.
● If you select a channel on which no signal is received, the
channel number is displayed regardless of this function setting.
● The setting you have made is kept in memory. Even if the VCR is
unplugged or the power failure occurs, it will resume every time
you turn on the VCR.
Ⅵ VIDEO CALIBRATION — ON/OFF
When this function is set to “ON”, this VCR checks the condition
of the tape in use during playback and recording, and
compensates to provide the highest-possible pictures. This takes
place whenever you play back a tape or start recording after
inserting a tape.
Ⅵ AUTO SP]EP TIMER — ON/OFF
When this function is set to “ON”, the VCR automatically
switches to EP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
NOTES:
For Example, Recording a program of 140 minutes in length onto
a 120-minute tape
● During playback, this function is always working even though
“VIDEO CALIBRATION” appears just at the beginning of
automatic tracking.
Approximately 110 minutes
Approximately 30 minutes
● During recording, this function works only for the first EP
recording and the first SP recording on an inserted tape.
● When you play back rental tapes or tapes recorded on other
VCRs, set this function either “ON” or “OFF” whichever gives
you the best picture.
SP mode
EP mode
Make sure you set this function to “ON” before the timer-
recording starts.
NOTES:
● If you have programed the VCR to timer-record 2 or more
programs, the second program and those thereafter may not fit
on the tape with this function set to “ON”. In this case, do not
use this function, but change the tape speed manually during
timer programing.
● In order to ensure that the recording fits on the tape, this
function may leave a slight non-recorded portion at the end of
the tape.
● There may be some noise and sound disturbance where the tape
speed switches from SP to EP mode on the tape.
● This function will not work properly on the following tapes:
T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
Ⅵ PICTURE CONTROL — AUTO(NORM)/EDIT/SOFT/SHARP
This function helps you to adjust the playback picture quality
according to your preference.
AUTO (NORM): Normally select this. Picture quality is adjusted
automatically. When “VIDEO CALIBRATION” is “OFF”, “NORM”
will appear instead of “AUTO”.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
SHARP: Clearer, sharper-edged picture when viewing images with
much flat, same-colored surfaces such as cartoons.
Ⅵ DIGITAL R3 — ON/OFF
When this function is set to “ON”, edge correction to the
luminance signal is performed to enhance details. Normally set
this function to “ON”.
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected
mode will not change until you select again.
● Select “EDIT” when you are editing tapes (੬ pg. 22). After you
finish editing the tapes, select “AUTO” (“NORM” when “VIDEO
CALIBRATION” is “OFF”.)
NOTES:
● Depending on the type of tape being used, picture quality may
be better with “DIGITAL R3” set to “OFF”.
● If you use this VCR as the playback VCR for editing, be sure to
set “DIGITAL R3” to “OFF” before starting.
Ⅵ AUTO TIMER — ON/OFF
● When this function is set to “ON”:
The timer recording standby mode is automatically engaged
when the VCR is turned off. It is temporarily canceled when the
VCR is turned on. You do not have to press TIMER to engage or
disengage the timer recording standby mode.
● When this function is set to “OFF”:
You have to press TIMER to engage or disengage the timer
recording standby mode.
Ⅵ VIDEO STABILIZER — ON/OFF
When this function is set to “ON”, you can automatically correct
vertical vibrations in the picture when playing back unstable
recordings made on another VCR.
NOTES:
● When you finish viewing a tape, be sure to set this function to
“OFF”.
Ⅵ ON SCREEN (REC) — ON/OFF
When this function is set to “ON”, if you press OSD (OK)
(੬ pg. 6) various VCR status information (on-screen display)
appears on the screen during recording.
● The on-screen display may jitter vertically when this function is
set to “ON”.
●
To watch recordings with close-caption, set this function to “OFF”.
— 18 —
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
Ⅵ 2ND AUDIO RECORD — ON/OFF
● Before recording, set “VIDEO CALIBRATION” to “ON”.
(੬ pg. 18)
● When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on both
the normal and Hi-Fi tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on
both the Hi-Fi and normal tracks.
● When this function is set to “OFF”, the SAP audio cannot be
recorded.
● You cannot activate the S-VHS ET function while recording
(੬ pg. 12), timer-recording (੬ pg. 15) or the “VIDEO
CALIBRATION” function (੬ pg. 18) is in progress.
● The S-VHS ET function does not work with S-VHS tape.
● To keep the highest quality recording and playback pictures
over a long period of time, S-VHS recording on S-VHS tape is
recommended.
● Use of high grade tapes are recommended for S-VHS ET
recordings. On some tapes, picture quality will not improve
even if the S-VHS ET function is used. Check the recording
quality before you start important recordings.
● While playing back a tape recorded with this function on some
tapes, noise may appear. (If playback picture becomes blurred
or interrupted, use a cleaning cassette.)
Ⅵ AUDIO MONITOR — HI-FI/HI-FI L/HI-FI R/NORM/MIX
This VCR can record two sound tracks simultaneously (normal and
Hi-Fi) on a tape. You can select the sound track(s) to listen to while
playing back a Hi-Fi stereo tape. In addition, when playing back a
prerecorded tape containing two separate audio programs on the
Hi-Fi tracks, you can choose either one by selecting either “HI-FI
L” or “HI-FI R”.
HI-FI: Normally select this. Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM: Sound on the normal track is played back.
MIX: Both sounds on the Hi-Fi track and normal track are mixed
and played back.
Ⅵ REC END RETURN — ON/OFF
Returning point for Playback, Repeat Play or Series Playback can
be set to tape end or recording end. (This VCR considers 1-second
unrecorded portion as the recording end.) When the returning
point is reached, playback stops and the cassette will be
automatically rewound.
NOTES:
● While playing back a monaural tape, sounds on the normal
track will be heard regardless of this setting.
ON: Playback stops at the end of the recording.
OFF: Playback stops at the end of tape.
● If RF connection (੬ pg. 7) is used for viewing pictures on the
TV, sound will be monaural even though you select “HI-FI”.
● You can also use the A.MONITOR button on the Remote to
select the desired monitor sound. (੬ pg. 11)
NOTE:
The setting you have made is kept in memory. Even if the VCR is
unplugged or the power failure occurs, it will resume every time
you turn on the VCR.
Ⅵ S-VHS MODE — ON/OFF
Ⅵ DAY/TIME INSERT — ON/OFF
You can determine which recording mode — either S-VHS mode
or VHS mode — is used for recording on S-VHS tapes.
● When this function is set to “ON”, you can record on S-VHS
tapes with S-VHS picture quality.
When this function is set to “ON”, you can record Month/Day/
Year and clock time display with your picture.
NOTES:
● To use this function, be sure to set “ON SCREEN (REC)” to
“ON”. ((੬ pg. 18))
● When this function is set to “OFF”, you can record on S-VHS
tapes with VHS picture quality.
● The setting you have made is kept in memory. Even if the VCR is
unplugged or the power failure occurs, it will resume every time
you turn on the VCR.
● This function is not available during Audio Dubbing or Insert
Editing.
NOTES:
● S-VHS mode allows you to make high quality video recordings
with horizontal resolution of 400 lines, comparing with the 230
lines of resolution of conventional VHS recordings. To achieve
the highest quality picture we recommended to record in S-VHS
mode. (But remember that a conventional VHS VCR without
SQPB cannot play back S-VHS tapes recorded in S-VHS mode.)
● S-VHS MODE setting does not affect recording on VHS tapes.
Recording on VHS tapes is always performed in VHS mode
except when using S-VHS ET mode (੬ pg. 19).
Ⅵ REC SAFETY — ON/OFF
Usually, you can only record onto a cassette with its record safety
tab intact. When this function is set to “OFF”, recording can be
done onto a cassette whose record safety tab is removed.
NOTES:
Ⅵ FRONT AUX INPUT — VIDEO/S-VIDEO
You have to select which terminal — either VIDEO (composite) or
S-VIDEO (Y/C separate signals) to use as the video input terminal
on the front panel.
Make sure to select the correct terminal; otherwise, you may fail
in recording (editing) on this VCR.
● The setting you have made is kept in memory. Even if the VCR is
unplugged or the power failure occurs, it will resume every time
you turn on the VCR.
● When “REC SAFETY” is set to “OFF”, playback does not start
automatically when you insert a cassette with its record safety
tab removed. (੬ pg. 12)
Ⅵ DAILY T. RECORD — NORM/AUTO REW
Ⅵ REAR AUX INPUT — VIDEO/S-VIDEO
You have to select which terminal — either VIDEO (composite) or
S-VIDEO (Y/C separate signals) to use as the video input terminal
on the rear panel.
Make sure you select the correct terminal; otherwise, you may fail
in recording (editing) on this VCR.
When you set daily timer recording, you can use one cassette
repeatedly. If you select “AUTO REW”, the VCR rewinds tape each
time after timer recording and the timer mode is engaged.
If you select “NORM”, the VCR turns off after timer recording.
Rewinds the tape or replace it, and engage timer recording
standby mode manually.
Ⅵ S-VHS ET — ON/OFF
When this function is set to “ON”, you can record on VHS
cassettes with S-VHS picture quality. Tapes recorded using this
function can be played back on most S-VHS VCRs or VHS VCRs
equipped with the S-VHS ET function or VHS VCR equipped with
the SQPB (S-VHS QUASI PLAYBACK) function.
When this function is set to “ON”, the S-VHS indicator lights up
on the display panel.
CONTINUED ON NEXT PAGE
— 19 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Auto Recording
Child Lock
You can automatically record a satellite program which is timer-
programed on your DBS receiver.
You can disable the VCR operations.
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
REW
FF
24HR QUICK
REC LINK PROGRAM
POWER
INSERT A.DUB
S-VIDEO
While the VCR is turned on, press and hold POWER 1 on the
Remote for more than 10 seconds.
The VCR turns off, “CL” appears for about 5 seconds on the
display panel, then the clock time appears again.
To release the child lock, press and hold POWER 1 on the
Remote until the VCR turns on.
NOTES:
● Pressing TIMER during timer recording, unplugging the AC
power cord or a power outage also releases the child lock.
● Even if the child lock function is in use, it is possible to engage
and disengage the timer mode with TIMER (#) on the Remote.
● Timer recording programs will be performed even if the child
lock function is activated.
● When the child lock function is in use, keep the Remote out of
the children’s reach.
A Connect aDBSreceivertothe AUDIO/VIDEO IN orS-VIDEOIN
connectors* on the rear panel. You can also connect the cable
box if it has a timer.
* To use these connectors, you have to select which one to use.
(੬ See pg. 19, “REAR AUX INPUT”.)
B Set timer program on DBS receiver referring to its instruction
manual.
C Load a cassette with the record safety tab intact.
D Press SP/EP to set the tape speed. The selected tape speed will
appear on the TV screen.
E Press REC LINK for more than 2 seconds. The VCR turns off
automatically and enter the Satellite Auto Recording standby
mode (“ ” and “#” light up). When signals come into the
VCR from the DBS receiver, the VCR starts recording (“#” and
“⅜” light up and “ ” blinks). When no signals come into the
VCR, the VCR stops recording (“⅜” goes off).
NOTES:
● Be sure not to turn on the DBS receiver before the program starts
broadcasting; otherwise, the VCR will start recording when the
DBS receiver is turned on.
● To disengage the Satellite Auto Recording standby mode, press
REC LINK (“ ” and “#” go off).
● Depending on the type of satellite receiver, Satellite Auto
Recording may not be compatible.
— 20 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Box or DBS Receiver Brand Setting
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Multi-Brand Remote Control
This Remote can control some functions of remote controllable
TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers
listed below. Without setting, you can control a JVC TV.
A Turn on cable box or DBS receiver
Turn on the cable box or DBS receiver using the Power button on
the unit or its Remote.
NOTES:
● Some unit’s brands have more than one code. If the unit does
not function with a specified code, try other codes.
● Depending on the type of unit, some or all functions cannot be
operated using this Remote.
B Enter brand code
A Press and hold CABLE/DBS.
B Press MBR SET.
C Press the Number keys to enter your cable box’s (or DBS
receiver’s) brand code.
D Press OK, and release CABLE/DBS.
● It is not possible to operate a unit not equipped with a remote
sensor.
● It is not possible to set the Remote for both your cable box and a
DBS receiver at the same time.
● Once you have set the Remote to operate the unit, you do not
have to set it until you replace the batteries from the Remote.
● If the batteries of the Remote are discharged, the Remote may
not be able to control the TV, cable box or DBS receiver.
Replace the batteries.
(Ex.) To set Remote to JVC 51:
MBRSET
CABLE/
DBS
A/B
1
5
Release
TV Brand Setting
Hold
down
Press in succession
A Turn on TV
Turn on the TV using the Power button on the TV or its Remote.
C Operate cable box or DBS receiver
While holding down CABLE/DBS, press one of the following
buttons: POWER 1, TV CH+/–, and the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
● To change the cable box’s (or DBS receiver’s) channels, press TV
CH+/– or the Number keys. (The CH+/– button can be used to
change the VCR’s channels only.)
B Set TV brand code
A Press and hold TV.
B Press MBR SET.
C Press the Number keys to enter your TV’s brand code.
D Press OK, and release TV. The TV should turn off.
(Ex.) To set Remote to RCA 05:
CABLE BOX BRAND
CODE
MBRSET
A/B
TV
ARCHER
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
5
0
Release
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
02
01, 17
15, 16, 17, 21, 25
15
01, 04, 06, 11, 12, 15, 28
10, 18, 23
15
01, 04, 06, 11, 12, 15, 28
02
07
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
01, 16, 17
05, 16, 24
02
Hold
down
Press in succession
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
C Operate TV
While holding down TV, press one of the following buttons:
POWER 1, TV/VCR, TV CH+/–, ^(TV Muting), TV VOL+/–,
and the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
TV BRAND
CODE
TV BRAND
CODE
JVC
01, 03
10
SONY
07
12
13
13
08
09
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SAMSUNG
SANYO
SEARS
02
REGAL
03
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
04, 11
05
TOSHIBA
ZENITH
SHARP
06
07
SL MARX
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
16, 17, 25
03, 09, 22
03, 09, 22
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
51
51
41
40
RCA (DSS)
CONTINUED ON NEXT PAGE
— 21 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Remote Control Code
Editing
This Remote is capable of transmitting two control codes; one set
to respond to A code control signals and another set to respond to
B code control signals. This Remote control is preset to send A
code signals because your VCR is initially set to respond to A code
signals. You can easily modify your VCR and the Remote to
respond to B code signals. When using two JVC VCRs, set two
VCRs and their Remotes to different codes, so that you can
operate these VCRs separately.
Editing with Another VCR
You can use your VCR as the playback or recording VCR. You can
use a camcorder as the playback VCR and your VCR as the
recording VCR. Refer also to the other components’ instruction
manuals for connection and its operations.
A Make connections
Example 1
A Set remote control code for Remote
A Press and hold A/B.
B Press the Number key “2”.
C Press OK, and release A/B.
● The Remote now can transmit B code control signals.
This VCR
To AUDIO/VIDEO IN,
S-VIDEO IN
To AUDIO/VIDEO OUT,
S-VIDEO OUT
(Ex.) To set Remote to B code:
MBRSET
A/B
Release
2
When using
When using
this VCR as the
recording VCR,
connect this
this VCR as the
playback VCR,
connect this
VCR’s AUDIO/
VIDEO OUT
connectors to
the audio/
video input
connectors on
another VCR.
Hold
down
Press in succession
VCR’s AUDIO/
Audio/Video
cable
(supplied)
S-video
cable
(supplied)
VIDEO IN
connectors to
theaudio/video
output
B Check remote control code for VCR
Press and hold 4 on the VCR for more than 5 seconds while the
VCR is turned off. The code currently set appears on the display
panel.
connectors on
another VCR.
C Change code for VCR
Press any key on the Remote. The VCR now responds to B code
control signals.
● To set the Remote and the VCR back to A code control signals,
repeat the same procedure as shown above except pressing the
Number key “1” in step B of 1.
To audio/video output,
S-Video out
To audio/video input,
S-Video input
Another VCR
To control two VCRs with the same Remote
● If another VCR is monaural, connect this VCR’s AUDIO L IN (or
OUT) connector to the audio output (or input) connector on
another VCR.
You can control two JVC VCRs by switching the remote control
code for the Remote between A and B (੬ step A), keeping two
VCRs to different control codes.
Example 2
● To change only the remote control code for the Remote, DO
NOT perform steps B and C.
This VCR (for recording)
To AUDIO input
To S-VIDEO input
Audio/Video cable
(supplied)
S-video cable
(supplied)
To audio output
To S-video output
Player
Camcorder
— 22 —
Download from Www.Somanuals.com. All Manuals Search And Download.
● Audio Dubbing is possible by using the audio input connectors
on the front panel or on the rear panel.
B Load cassettes
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
This VCR
C Select input mode on recording VCR
Select the correct external input on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select “L-1” — when connecting the other VCR to the audio/video
(or S-video) input connectors on the rear panel.
To AUDIO input
Select “F-1” — when connecting the other VCR to the audio/video
(or S-video) input connectors on the front panel.
Press AUX or CH+/– on the Remote. Or push the JOG dial, then
turn it to the left or right.
D Select video input connector on recording VCR
When using this VCR as the recording VCR, select the appropriate
mode depending on the connector being used (੬ pg. 19).
When using S-VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “S-VIDEO”.
When using S-VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “S-VIDEO”.
When using VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “VIDEO”.
To AUDIO output
CD player, etc.
When using VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “VIDEO”.
B Select input mode
E Select edit mode
Select “F-1” —when connecting the audio component to the
audio input connectors on the front panel.
Set the edit mode to “ON” for the VCRs if such a mode is
equipped.
Select “L-1” —when connecting the audio component to the
audio input connectors on the rear panel.
Press AUX or CH+/– on the Remote. Or push the JOG dial, then
turn it to the left or right.
● On this VCR, set “PICTURE CONTROL” to “EDIT” (੬ pg. 18).
F Start playback
Press PLAY (4) on the playback VCR.
G Start recording
C Locate start point, and engage Audio Dubbing mode
Press REC (7) on the recording VCR.
Load a cassette and press PLAY (4) on the VCR. Press PAUSE (9)
at the point where you want to start dubbing, then press A.DUB.
● The VCR enters the Audio Dubbing Pause mode. “⅜” blinks
and “$” lights on the display panel.
Various connection for editing tapes
The following three methods can be used for editing tapes.
● VHS to S-VHS editing (VIDEO-VIDEO connection):
Although the picture quality is inherently limited by the
original VHS quality, the edited tape has better picture quality
than those made by VHS-to-VHS editing.
D Start dubbing
Engage the Play mode of the audio component, then press PLAY
(4) on the VCR. Audio Dubbing begins at this point.
● To pause dubbing, press PAUSE (9). Press PLAY (4) to resume
dubbing.
● S-VHS to VHS editing (VIDEO-VIDEO connection):
Since the original source is recorded in S-VHS mode, the
edited tape has better picture quality than those made by
VHS-to-VHS editing.
E End Audio Dubbing
Press STOP (8) on the Remote or STOP/EJECT (0) on the VCR,
then engage the Stop mode of the audio component.
● S-VHS to S-VHS (S-VIDEO connection):
Original picture quality of S-VHS made can be duplicated
with minimal picture degradation. This is the best editing
method you can use on S-VHS VCRs.
NOTES:
● When monitoring the sound during Audio Dubbing, the normal
soundtrack is automatically selected. If you wish to hear the
Hi-Fi or mixed sound (Hi-Fi + normal soundtracks), press
A.MONITOR to select “NORM HI-FI”. (੬ pg. 11, “Selecting
monitor sound”)
Audio Dubbing
Audio Dubbing replaces the normal audio sound of a previously
recorded tape with a new soundtrack.
● Audio Dubbing stops automatically when the counter reaches
“0:00:00”, and the VCR enters the Play mode. Check the
counter reading on the screen before dubbing.
● “DAY/TIME INSERT” (੬ pg. 19) is not available during Audio
Dubbing.
Normal track
Before audio
dubbing
● Audio Dubbing is not possible with a cassette whose record
safety tab has been removed. If you want to record onto a tape
with its record safety tab removed, set “REC SAFETY” to “OFF”
(੬ pg. 19).
Video and
Hi-Fi track
● When playing back an audio-dubbed tape, press A.MONITOR
to select the soundtrack you wish to hear. (੬ pg. 11, “Selecting
monitor sound”)
After audio
dubbing
● Picture may be distorted if you pause Audio Dubbing.
A Make connections
Connect an audio cable between the VCR’s audio input
connectors and the audio component’s audio output connectors.
● When connecting a monaural audio component, use only the
VCR’s AUDIO L input connector.
CONTINUED ON NEXT PAGE
— 23 —
Download from Www.Somanuals.com. All Manuals Search And Download.
B Select input mode
Insert Editing and AV Dubbing
You can replace a recorded scene with new scene recorded on
another tape or with other material. Both the picture and the sound
recorded on the Hi-Fi sound track are replaced at the same time.
Select “F-1” —when connecting the other component to the
audio/video input connectors on the front panel.
Select “L-1” —when connecting the other component to the
audio/video input connectors on the rear panel.
Press AUX or CH+/– on the Remote. Or push the JOG dial, then
turn it to the left or right.
Insert Editing:
Source tape
C Select video input connector
Select the appropriate mode depending on the connector being
used (੬ pg. 19).
When using S-VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “S-VIDEO”.
When using S-VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “S-VIDEO”.
Edited tape
Before
editing
When using VIDEO input connector on the front panel, set
“FRONT AUX INPUT” to “VIDEO”.
When using VIDEO IN connector on the rear panel, set “REAR
AUX INPUT” to “VIDEO”.
Normal track
After
editing
D Select edit mode
Set the edit mode to “ON” for the VCRs if such a mode is
equipped.
● On this VCR, set “PICTURE CONTROL” to “EDIT” (੬ pg. 18).
Video and Hi-Fi track
AV Dubbing:
You can perform Audio Dubbing and Insert Editing at the same
time. This means that the picture and the sounds recorded on the
Hi-Fi sound track and on the normal track are replaced at the
same time.
● For AV Dubbing, you can edit pictures and sound using different
sources; connect a video source to the video input connector,
and an audio source to the audio input connectors.
E Locate end point
A Load the cassette to be edited into the VCR and press PLAY (4).
B Press PAUSE (9) when you find the end of the scene for which
you want to edit.
C Press C.RESET so that the counter reading becomes “0:00:00”.
F Locate start point, and engage Insert Editing mode
Press REW (3), then press PAUSE (9) when you find the
beginning of the scene for which you want to edit, then press
INSERT.
Source tape
● The VCR enters the Insert Editing Pause mode. “⅜” and “$”
light on the display panel.
Edited tape
● If you want to perform AV Dubbing and replace the picture,
Hi-Fi audio soundtrack and normal audio soundtrack all at the
same time, press INSERT, then press A.DUB also.
Before
editing
G Start editing
Load the source cassette and engage the Play mode of the other
component, then press PLAY (4) on the VCR. Insert Editing begins
at this point.
● Insert Editing stops automatically when the counter reaches
“0:00:00”, and the VCR enters the Play mode.
After
editing
A Make connections
To stop editing any time during recording
Press STOP (8) on the Remote or STOP/EJECT (0) on the
VCR, then engage the Stop mode of the other component.
Connect an audio/video cable between the VCR’s audio/video
input connectors and the other component’s audio/video output
connectors.
NOTES:
● Insert Editing and AV Dubbing are possible by using the audio/
video input connectors on the front panel or on the rear panel.
● Be sure to select “AUTO” for “PICTURE CONTROL” (or
“NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
you finish editing (੬ pg. 18).
● Editing is not possible with a cassette whose record safety tab
has been removed. If you want to record onto a tape with its
record safety tab removed, set “REC SAFETY” to “OFF”
(੬ pg. 19).
This VCR (for recording)
To AUDIO/VIDEO IN
To S-VIDEO IN
● The recording speed (SP/EP) is determined by the previous
recording to be replaced. If the recording speed changes on the
tape to be edited while editing the tape, the inserted picture will
be distorted where the recording speed changes.
● When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.
Audio/video cable
(supplied)
S-video cable
(supplied)
● DAY/TIME INSERT (੬ pg. 19) is not available during Insert
Editing.
To audio/video output
To S-video output
Another VCR (for playback)
— 24 —
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNER
Specifications
Tuning system
Channel coverage
VHF
UHF
CATV
RF output
: Frequency-synthesized tuner
: Channels 2–13
: Channels 14–69
: 113 Channels
GENERAL
Power requirement
Power consumption
Power on
: AC 120 Vd, 60 Hz
: Channel 3 or 4 (switchable; preset to
Channel 3 when shipped) 75 ohms,
unbalanced
: 19 W
: 1.6 W
Power off
Temperature
Operating
Storage
Operating position
Dimensions (W x H x D) : 435 mm x 94 mm x 242 mm
(17-3/16" x 3-3/4" x 9-3/4")
TIMER
Clock reference
Program capacity
: 5°C to 40°C (41°F to 104°F)
: –20°C to 60°C (–4°F to140°F)
: Horizontal only
: Quartz
: 1-year programmable timer/
8 programs
Memory backup time
: Approx. 27 months
Estimated figure base on supplied
fresh battery; actual performance may
differ.
Weight
Format
Maximum recording time
: 2.8 kg (6.2 lbs)
: S-VHS/VHS NTSC standard
SP
EP
: 210 min. with ST-210 video cassette
: 630 min. with ST-210 video cassette
ACCESSORIES
Provided accessories
: Infrared remote control unit,
“AA” battery x 2,
S-video cable (4-pin),
RF cable (F-type)
VIDEO/AUDIO
Signal system
: NTSC-type color signal and EIA
monochrome signal, 525 lines/
60 fields
Audio/Video cable
BNC/RCA adapter x 2
Recording/Playback
system
: DA-4 (Double Azimuth) head helical
scan system
Specifications shown are for SP mode unless specified otherwise.
● E. & O.E. Design and specifications subject to change without
notice. Don’t service the product yourself.
Signal-to-noise ratio
Horizontal resolution
VHS
: 45 dB
: 230 lines
: 400 lines
S-VHS
Frequency range
Normal audio
Hi-Fi audio
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
Input/Output
: RCA connectors (IN x 2, OUT x 1)
S-video connectors (IN x 2, OUT x 1)
— 25 —
Download from Www.Somanuals.com. All Manuals Search And Download.
S
Index
Second Audio Recording ..............................................12
Semiauto Clock Set .........................................................8
Skip Search ...................................................................11
S-VHS (Super VHS), S-VHS ET or VHS Recording Mode 13
S-VHS ET ......................................................................19
S-VHS MODE ...............................................................19
S-video Connection ........................................................7
List of Terms
This guide serves as a quick way to locate frequently used terms
and on-screen display names.
A
AUDIO MONITOR ................................................ 11, 19
Auto Channel Set ........................................................... 9
AUTO SP]EP TIMER ................................................... 18
AUTO TIMER ............................................................... 18
AV Connection ............................................................... 7
T
To control two VCRs with the same Remote .................22
To recall an indication ....................................................6
Tracking Adjustment .....................................................11
TV Brand Setting ...........................................................21
C
V
Cable Box or DBS Receiver Brand Setting .................... 21
VIDEO CALIBRATION ..................................................18
VIDEO STABILIZER ......................................................18
D
DAILY T. RECORD ....................................................... 19
DAY/TIME INSERT ....................................................... 19
DIGITAL R3 ................................................................. 18
DIGITAL TBC/NR ......................................................... 18
During playback ........................................................... 10
Pause and Frame-by-Frame playback ...................... 10
Pause playback and view still picture ..................... 10
Picture Search ......................................................... 10
Stop playback ......................................................... 10
Variable-Speed Picture Search ................................ 10
During recording .......................................................... 12
Pause recording ...................................................... 12
Stop recording ........................................................ 12
W
Watching one program while recording another ...........12
When the tape is not running ........................................10
Eject the cassette .....................................................10
Rewind/fast-forward ................................................10
Turn off the VCR .....................................................10
2ND AUDIO RECORD .................................................19
F
FRONT AUX INPUT ..................................................... 19
I
Index Search ................................................................ 11
Instant Review .............................................................. 11
M
Manual Channel Set ....................................................... 9
Manual Clock Set ........................................................... 8
N
Next Function Memory ................................................ 11
O
ON SCREEN (PLAY) ..................................................... 18
ON SCREEN (REC) ....................................................... 18
P
PICTURE CONTROL .................................................... 18
Playback Resume Function ........................................... 11
R
REAR AUX INPUT ........................................................ 19
REC END RETURN ....................................................... 19
REC SAFETY ................................................................. 19
Recording Resume Function ......................................... 12
Repeat Play .................................................................. 11
Repeat Recording ......................................................... 12
RF Connection ............................................................... 7
— 26 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this
can save you from the trouble of sending your VCR off for repair.
Power
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
● Connect the AC power cord.
● Press and hold POWER 1 for more than
10 seconds to release the Child Lock function.
(੬ pg. 20)
The power will not come
on.
● The AC power cord is disconnected.
● The Child Lock function is activated.
The clock works, but the
VCR’s power will not come
on.
● The VCR is in the timer recording standby mode ● Press TIMER to disengage the timer.
with “AUTO TIMER” set to “OFF” (੬ pg. 18).
● The Child Lock function is activated.
● Press and hold POWER 1 for more than
10 seconds to release the Child Lock function.
(੬ pg. 20)
The Remote will not
function.
● The batteries are discharged.
● The VCR is in the timer recording standby mode. ● Press TIMER to disengage the timer.
● Replace batteries.
● Remote control A/B code is wrong.
● Reset A/B code. (੬ pg. 22)
Playback
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The tape is running but the ● If the RF connection (੬ pg. 7) is used to view the ● Select channel 3 or 4 on the TV.
picture will not appear.
picture, the channel on the TV is set incorrectly.
● If the AV or S-video connection (੬ pg. 7) is used ● Select the AV mode on the TV.
to view the picture, the TV receiver is set to the
wrong mode.
Recording
SYMPTOM
POSSIBLE CAUSE
● There is no cassette loaded.
CORRECTIVE ACTION
Recording will not start.
● Insert a cassette on which the record safety tab is
intact.
● “REC SAFETY” is set to “ON” and the loaded
cassette has had its record safety tab removed.
● Set “REC SAFETY” to “OFF” (੬ pg. 19).
Timer Recording
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Timer recording will not
work.
● The clock and/or the timer program have been set ● Set the clock and/or timer program correctly.
incorrectly.
● The timer is not engaged.
● Press TIMER to engage the timer and make sure
that # appears on the display panel.
● The VCR has not been set up properly.
● Re-perform the set-up procedures. Make sure you
have compensated for guide channel and VCR
channel number mismatches. (੬ pg. 15)
Timer programing will not ● Timer recording is in progress.
work.
● Timer programing cannot be performed when
timer recording is in progress. Wait until it finishes.
You moved, and now VCR ● The receivable stations in the new area are
● Re-perform the procedure in “Changing VCR
Plus+ system does not
work properly
received on different channels than those in the
previous area.
Plus+® Setting” (੬ pg. 15).
Other Problems
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The channel cannot be
changed.
● Recording is in progress.
● Press PAUSE (9) to pause the recording, change
channels, then press PLAY (4) to resume
recording.
Even though Auto or
Semiauto Clock Set has
been performed, the clock
is incorrect.
● The clock setting data received from the host
channel is incorrect.
● Select a different host channel during Semiauto
Clock Set (੬ pg. 8), or perform Manual Clock Set
(੬ pg. 8).
Buttons and controls do
not function at all.
● Mode Lock is activated.
● Press and hold OK on the Remote for more than 5
seconds to deactivate Mode Lock.
— 27 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
0104 ASR-PR-BJ
COPYRIGHT © 2004 VICTOR COMPANY OF JAPAN, LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Infantino Baby Carrier Comfort Rider User Manual
Insignia Camera Accessories NS A700PF6 User Manual
Insignia Work Light NS 24E200NA14 User Manual
Invacare Mobility Aid 6265E User Manual
Jensen Portable Multimedia Player SMPV 1GBS User Manual
Jet Tools Saw M 708955Z User Manual
John Deere Impact Driver AT 3701 J User Manual
JVC DVD Player DR MX10SEK User Manual
Kenwood Stereo Receiver AT 200 User Manual
King Canada Air Compressor 8496K User Manual