JVC VCR HR A57U User Manual

VIDEO CASSETTE RECORDER  
HR-A57U HR-A37U  
INSTRUCTIONS  
LPT0497-001A  
COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.  
Printed in China  
1100 IYVfIDfBJ  
Dear Customer,  
CAUTION:  
Thank you for purchasing the JVC VHS video cassette recorder.  
Before use, please read the safety information and precautions to  
ensure safe use of your new VCR.  
Changes or modifications not approved by JVC could void  
users authority to operate the equipment.  
Declaration of Conformity  
CAUTIONS  
Model Number:  
HR-A57U  
HR-A37U  
JVC  
Trade Name:  
Responsible Party: JVC Americas Corp.  
Address:  
1700 Valley Road Wayne, N.J. 07470  
Telephone Number: 973-315-5000  
This device complies with Part 15 of FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
The lightning flash with arrowhead symbol, within  
an equilateral triangle, is intended to alert the user  
to the presence of uninsulated “dangerous voltage”  
within the products enclosure that may be of  
sufficient magnitude to constitute a risk of electric  
shock to persons.  
Failure to heed the following precautions may result in damage  
to the VCR, Remote or video cassette.  
1. DO NOT place the VCR …  
… in an environment prone to extreme temperatures or  
humidity.  
… in direct sunlight.  
… in a dusty environment.  
… in an environment where strong magnetic fields are  
generated.  
The exclamation point within an equilateral triangle  
is intended to alert the user to the presence of  
important operating and maintenance (servicing)  
instructions in the literature accompanying the  
appliance.  
… on a surface that is unstable or subject to vibration.  
2. DO NOT block the VCRs ventilation openings.  
3. DO NOT place heavy objects on the VCR or on the Remote.  
4. DO NOT place anything which might spill on the top of the  
VCR or on the Remote.  
WARNING:  
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE  
THIS UNIT TO RAIN OR MOISTURE.  
5. AVOID violent shocks to the VCR during transport.  
CAUTION:  
For Customer Use:  
This video cassette recorder should be used with AC 120Vd,  
60Hz only.  
Enter below the Model No. and Serial No. which are located  
on the rear of cabinet. Retain this information for future  
reference.  
To prevent electric shocks and fire hazards, DO NOT use any  
other power source.  
Model No.  
Serial No.  
CAUTION:  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF  
PLUG TO WIDE SLOT, FULLY INSERT.  
ATTENTION:  
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA  
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE  
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU  
FOND.  
Cassettes marked “VHS” (or “S-VHS”) can be used with this  
video cassette recorder. However, S-VHS recording is not  
possible with this model.  
This model is equipped with SQPB (S-VHS QUASI PLAYBACK)  
that makes it possible to play back S-VHS recordings with  
regular VHS resolution.  
HQ VHS is compatible with existing VHS equipment.  
As an ENERGY STAR® Partner, JVC has determined that this  
product or product model meets the ENERGY STAR® guidelines  
for energy efficiency.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installers  
attention to Article 820-40 of the NEC that provides guidelines  
for proper grounding and, in particular, specifies that the cable  
ground shall be connected to the grounding system of the  
building, as close to the point of cable entry as practical.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICING  
1. Servicing  
Buttons, Connectors  
and Indicators  
If your product is not operating correctly or exhibits a marked  
change in performance and you are unable to restore normal  
operation by following the detailed procedure in its operating  
instructions, do not attempt to service it yourself as opening or  
removing covers may expose you to dangerous voltage or other  
hazards. Refer all servicing to qualified service personnel.  
2. Damage Requiring Service  
Unplug this product from the wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into the  
product.  
Front Panel (HR-A57U)  
Cassette  
loading slot  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as an improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the product to its normal operation.  
e. If the product has been dropped or damaged in any way.  
f. When the product exhibits a distinct change in performance—  
this indicates a need for service.  
VIDEO/AUDIO  
input connectors  
Remote  
sensor  
3. Replacement Parts  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer or which have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock or other hazards.  
Timer mode indicator  
Display panel  
Play indicator  
VCR mode  
indicator  
4. Safety Check  
Record  
indicator  
Upon completion of any service or repairs to this product, ask the  
service technician to perform safety checks to determine that the  
product is in safe operating condition.  
Channel and auxiliary input/Clock time  
How to use the Remote  
Before use, insert two AA size batteries into the Remote with the  
polarity ( and ) matched correctly as indicated on the battery  
compartment or on the lid.  
The Remote can operate most of your VCRs functions, as well as  
basic functions of TV sets, cable boxes and DBS receivers.  
Point the Remote toward the remote sensor on the target  
component.  
Front Panel (HR-A37U)  
Cassette  
loading slot  
The maximum operating distance of the remote control is about  
8 m.  
NOTE:  
If the Remote does not work properly, remove its batteries, wait for  
a few seconds, replace the batteries and then try again.  
Video heads cleaning  
Use a dry cleaning cassette TCL-2UX when:  
Rough, poor picture appears while a tape is played back.  
The picture is unclear or no picture appears.  
USE CLEANING CASSETTEappears on the screen (only with  
SUPERIMPOSEset to ON).  
VIDEO/AUDIO  
input connectors  
Remote  
sensor  
Timer mode indicator  
Display panel  
Play indicator  
VCR mode  
indicator  
Record  
indicator  
Channel and auxiliary input/Clock time  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Connections and Plug&Play Setting –  
Rear Panel (HR-A57U)  
AC power cord  
Remote  
Number keys  
Rear Panel (HR-A37U)  
AC power cord  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Connections and Plug&Play Setting –  
On-screen display  
Connections and  
If you press OSD on the Remote when “SUPERIMPOSE” is set to  
“ON”, you can see the current VCR status on the TV screen. Press  
OSD again to exit on-screen display.  
Plug&Play Setting  
The indications are not recorded even if the VCR is in the  
recording mode.  
A Check contents  
Make sure the package contains all of the accessories listed in  
“Specifications”.  
A
L
B Situate VCR  
Place the VCR on a stable, horizontal surface.  
CH125  
RECORD K  
PAUSE  
C Connect VCR to TV  
HR-A57U  
THU 12:00 AM  
B
C
D
STEREO –WARNING–  
SAP  
SP J  
TIMER RECORDING  
Antenna or cable  
TO START SOON  
(CANCEL)  
I
H
G
F
Coaxial cable  
+
+
+
E
1
B
INDEX  
Flat feeder  
NORM  
HI-FI  
E
COUNT  
–1:23:45  
Matching transformer  
(not supplied)  
A Channel and auxiliary input  
B Day and clock time  
AC power cord  
C STEREO program indication (HR-A57U only)  
D SAP indication (HR-A57U only)  
E Audio monitor indications (HR-A57U only)  
F Time counter  
G Index number  
H Tape position  
I Cassette mark  
Back of VCR  
AC outlet  
J Tape speed  
K VCR operation mode  
L Timer warning display  
To audio/video  
input connectors  
Audio/video cable  
(not supplied)  
RF cable  
(supplied)  
To 75 terminal  
TV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Connections and Plug&Play Setting –  
HR-A37U  
D Perform Plug&Play setup  
Plug the AC power code into an AC outlet. Do not turn on the  
VCR. The clock and tuner channels will be set automatically. The  
time and date can be set automatically by the clock setting data  
transmitted from one of the regular TV broadcast channels. We  
call this TV channel the host channeland it is a PBS channel in  
your area.  
Antenna or cable  
Coaxial cable  
Flat feeder  
ATTENTION:  
If you use a cable box, Plug&Play will not function; set the clock  
and tuner channels separately.  
Matching transformer  
(not supplied)  
During Initial Auto Clock Set  
Autblinks.  
AC power cord  
During Auto Channel Set  
The channel numbers are displayed as they are  
scanned and set.  
Plug&Play Completed  
The current time is displayed.  
What to do if Plug&Play setting failed  
Back of VCR  
AC outlet  
If an incorrect time is displayed on the display panel, perform  
the Semiauto Clock Setor Manual Clock Setprocedure.  
If “–:– –” appears on the display panel, ensure that the antenna  
cable is connected correctly. Then turn on and off the VCR; the  
Plug&Play setting will be automatically reactivated. If Plug&Play  
setting is not performed though the antenna cable is connected  
correctly, perform Manual Clock Setand Auto Channel Set”  
or Manual Channel Set.  
To audio/video  
input connectors  
E Set VCR channel  
Audio/video cable  
(not supplied)  
The VCR channel is the channel on which you can watch the  
picture from the VCR on the TV when only using the RF  
connection. Press POWER to turn off the VCR, then press STOP/  
EJECT (0) on the VCR for more than 5 seconds. CH3”  
appears on the display panel. Press CH+/– on the Remote to  
select CH3, CH4or CH–”(OFF), then press OK.  
The VCR channel is preset to CH3. Set to CH4if CH3 is  
used for broadcasting in your area.  
RF cable  
(supplied)  
To 75 terminal  
TV  
F Final preparation for use  
Turn on the VCR and the TV, and select the VCR channel 3 or 4  
(or AV mode) on the TV. You can now perform basic playback or  
basic recording.  
RF Connection  
A Disconnect the TV antenna from the TV.  
B Connect the TV antenna cable to the ANT. IN terminal on the  
rear of the VCR.  
C Connect the supplied RF cable between the TV OUT terminal  
on the rear of the VCR and the TVs antenna input terminal.  
AV Connection  
(improves picture quality during tape playback.)  
If your TV is equipped with audio/video input connectors  
A Connect the antenna, VCR and TV as shown in the illustration.  
B Connect an audio/video cable between the AUDIO/VIDEO  
OUT connectors on the rear of the VCR and the audio/video  
input connectors on the TV.  
Even if you are using audio/video cables to connect your VCR to  
your TV, you must also connect it using the RF cable. This will  
ensure that you can record one show while watching another.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                              
                                                                              
                                                                    
                                                                     
                                                                        
                                                                        
                                   
                                    
                                       
                                       
C Select D.S.T. mode  
Initial Settings  
Press OK or e to move the highlight bar to D.S.T., then press  
rt repeatedly until the desired setting is selected.  
AUTO: Select if you want to adjust your VCRs clock  
automatically by the incoming signal from the host  
channel. (Auto Daylight Saving Time enables automatic  
adjustment of the VCRs clock at the start and end of  
Daylight Saving Time.) Be sure to select the correct time  
zone manually in step 4.  
Language Setting  
The default setting is ENGLISH.  
MAIN MENU  
A Access Main Menu screen, then  
ON:  
OFF:  
Adjustment will be made by the built-in clock itself.  
Select when Daylight Saving Time does not apply to you.  
FUNCTION SET  
TUNER SET  
INITIAL SET  
Initial Set screen  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to INITIAL  
SET, then press OK or e.  
D Select time zone  
Press OK or e to move the highlight bar to TIME ZONE, then  
press rt repeatedly until AUTOor the desired time zone is  
selected. Each time you press the button, the time zone changes  
as follows:  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Select language  
INITIAL SET  
CLOCK SET  
This VCR offers you the language choice to  
view menus and some messages in  
English, Spanish or French. Press rt to  
move the highlight bar (arrow) to  
LANGUAGE, then press OK or e  
repeatedly until the desired language is  
selected.  
LANGUAGE  
ENGLISH  
{ AUTO { ATLANTIC { EASTERN { CENTRAL  
{ MOUNTAIN { PACIFIC { ALASKA { HAWAII  
{ (back to the beginning)  
GUIDE CHANNEL SET  
SELECT WITH (  
PRESS (MENU) TO END  
,
) AND (OK)  
E Complete Semiauto Clock Set  
Press MENU to return to normal screen. Turn off the VCR. Aut”  
will appear on the display panel while the clock is being set. The  
current clock time will appear automatically when the clock  
setting is complete.  
Press MENU to return to normal screen.  
Clock Setting  
Setting clock manually  
— Manual Clock Set  
Perform clock setting only if the clock has not been set correctly  
by the Plug&Play setting or if you use a cable box.  
First follow steps 1 to 2 in Preparationsabove, then go to the  
following steps.  
Preparations  
A Access Main Menu screen, then  
CLOCK SET  
A Set time, date and year  
Press rt until the desired time appears,  
then press OK or e. Set the date and year  
in the same way.  
Holding rt [CHRT] changes the time  
in 30-minute intervals, or changes the  
date in 15-day intervals.  
MAIN MENU  
TIME  
DATE  
1/  
YEAR  
00  
– –:– –AM  
1
FUNCTION SET  
AUTO CLOCK : ON  
Initial Set screen  
TUNER SET  
HOST CH  
D.S.T.  
: AUTO  
: AUTO  
(CATV)  
INITIAL SET  
Press MENU on the Remote. Press rt to  
TIME ZONE : AUTO  
move the highlight bar (arrow) to INITIAL  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Access Clock Set screen  
Press rt to move the highlight bar  
(arrow) to CLOCK SET, then press OK or  
e.  
INITIAL SET  
CLOCK SET  
CLOCK SET  
B Select D.S.T. mode  
Press OK or e to move the highlight bar to  
D.S.T., then press rt to select the  
desired setting.  
TIME  
DATE  
YEAR  
00 SUN  
LANGUAGE  
ENGLISH  
1:00AM  
12/ 24  
GUIDE CHANNEL SET  
AUTO CLOCK : OFF  
D.S.T.  
: ON  
ON: Adjustment will be made by the  
built-in clock itself.  
SELECT WITH (  
,
) AND (OK)  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
PRESS (MENU) TO END  
OFF: Select when Daylight Saving Time  
does not apply to you.  
Setting clock semiautomatically  
— Semiauto Clock Set  
C Start clock  
Press MENU and normal screen appears.  
You can change the host channel/D.S.T. (Daylight Saving Time)/  
time zone setting manually. First follow steps 1 to 2 in  
Preparationsabove, then go to the following steps.  
To make corrections any time during the process  
Press OK or e repeatedly until the item you want to change  
blinks, then press rt.  
NOTE:  
The time set previously will be erased when “AUTO CLOCK”,  
“HOST CH”, “D.S.T.” or “TIME ZONE” setting is changed.  
CLOCK SET  
A Set Auto Clock to ON  
TIME  
DATE  
12/24  
YEAR  
Press OK or e on the Remote repeatedly  
to move the highlight bar to AUTO  
CLOCK, then press rt so that ONis  
selected.  
1:00PM  
00 SUN  
AUTO CLOCK : ON  
HOST CH  
D.S.T.  
: AUTO  
: AUTO  
(CATV)  
TIME ZONE : AUTO  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Select host channel  
You can either select AUTOor enter a PBS channel number.  
Press OK or e to move the highlight bar to HOST CH, then  
press rt repeatedly until AUTOor the desired PBS channel  
number is selected.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Initial Settings –  
Tuner Setting  
Playback  
Setting channels automatically  
— Auto Channel Set  
Basic Playback  
A Load a cassette  
Perform Auto Channel Set only if channels have not been set  
correctly by the Plug&Play setting.  
MAIN MENU  
A Access Main Menu screen, then Tuner  
FUNCTION SET  
Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to TUNER  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Perform Auto Channel Set  
TUNER SET  
Make sure the window side is up, the rear label side is facing you  
and the arrow on the front of the cassette is pointing towards the  
VCR.  
Do not apply too much pressure when inserting.  
The VCR turns on, and the counter on the on-screen display is  
reset, automatically.  
BAND  
CATV  
Press rt to move the highlight bar  
(arrow) to AUTO CHANNEL SET, then  
press OK or e. The VCR selects the correct  
band (TV or CATV) automatically during  
Auto Channel Set.  
AUTO CHANNEL SET  
MANUAL CHANNEL SET  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
When Auto Channel Set is complete,  
SCAN COMPLETEDappears on  
screen.  
If the cassettes record safety tab has been removed, playback  
begins automatically.  
AUTO CHANNEL SET  
If the scan was unsuccessful, SCAN  
COMPLETEDNO SIGNAL–” appears  
on screen. Check the connections and  
start again.  
SCANNING...  
B Start playback  
Press PLAY (4).  
PRESS (MENU) TO END  
Press MENU to return to normal screen.  
During playback  
Stop playback  
Setting channels manually  
— Manual Channel Set  
Press STOP (8) on the  
Remote.  
OR Press STOP/EJECT (0) on  
You can add the channels you want or delete the channels you do  
not want manually.  
the VCR.  
Pause playback and view still picture  
MAIN MENU  
A Access Main Menu screen, then Tuner  
Press PAUSE (9).  
FUNCTION SET  
Press PLAY (4) to resume normal playback.  
Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
Pause and Frame-by-Frame playback  
move the highlight bar (arrow) to TUNER  
Press PAUSE (9) to pause, then press 6 (or PAUSE (9))  
repeatedly.  
Press PLAY (4) to resume normal playback.  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Access Manual Channel Set screen  
Press rt to move the highlight bar  
(arrow) to MANUAL CHANNEL SET,  
then press OK or e.  
TUNER SET  
Rewind/fast-forward  
BAND  
CATV  
AUTO CHANNEL SET  
MANUAL CHANNEL SET  
Press REW (3) or FF (5).  
Press PLAY (4) to resume normal playback.  
If you press and hold REW (3) or FF (5) for more than  
2 seconds, simply releasing it cancels the picture search, and  
normal playback resumes.  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
MANUAL CHANNEL SET  
C Add or skip desired channels  
To add channels  
Rewind/fast-forward at variable speed (including slow-motion)  
(CATV)  
CH 45 ADD  
A Press the Number keys on the Remote  
to input a channel number you want to  
add.  
B Press OK or e to set to ADD.  
C Repeat A to B to add other channels.  
Press MENU to return to normal screen.  
To skip channels  
Press 2 or 6 repeatedly.  
Press PLAY (4) to resume normal playback.  
PRESS NUMBER KEY (09)  
Each time you press 2 or 6, the playback speed changes.  
To decrease the speed during picture search, press the opposite  
direction button repeatedly.  
During still picture, press and hold 6 to start forward slow  
motion playback. When you release the button, still picture  
resumes. During still picture, holding PAUSE (9) for more than  
2 seconds also starts forward slow motion playback. If you  
press PAUSE (9) again, still picture resumes.  
OR (  
,
), THEN (OK)  
PRESS (MENU) TO END  
A Press rt or the Number keys to select a channel number you  
want to skip.  
B Press OK or e to set to SKIP.  
C Repeat A and B to skip other channels. Press MENU to return  
to normal screen.  
Reverse  
Forward  
Reverse  
search  
3 steps  
Reverse  
play  
Slow  
motion  
1 step  
Normal Forward  
play  
search  
4 steps  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Playback –  
Playing back tape repeatedly (100 times)  
— Repeat Play  
When the tape is not running  
Rewind/fast-forward at high speed  
Press REW (3) or FF (5).  
Eject the tape  
During playback, press and hold PLAY (4) for more than  
5 seconds. The play indicator ($) on the display panel starts  
blinking slowly. To stop playback, press STOP (8) on the Remote  
or STOP/EJECT (0) on the VCR.  
Press STOP/EJECT (0).  
You can also eject the cassette when the VCR is turned off.  
Locating beginning of recordings  
— Index Search  
Turn off the VCR  
Press POWER.  
Index codes are placed on the tape at the beginning of each  
recording when recording on this VCR.  
A While the tape is not running, press SHUTTLE PLUS 2 or  
Playback Features  
6 on the Remote to start search.  
B To access a recording of 2 to 9 index  
codes away, press 2 or 6  
Adjusting tracking condition  
— tracking adjustment  
repeatedly until the correct number is  
displayed on the screen (only if  
Automatic tracking adjustment  
“SUPERIMPOSE” is set to “ON”).  
INDEX  
1
Whenever you insert a tape and start playback, automatic tracking  
starts working and continuously analyzes the signal to enable  
optimum picture quality during playback.  
Playback begins automatically when  
the desired recording is located.  
Manual tracking adjustment  
If automatic tracking cannot eliminate noises well during  
playback, follow the procedures below.  
Beginning of the  
current program  
recorded  
Beginning of the  
2nd next program  
recorded  
Current  
position on  
the tape  
A Press SP/EP on the Remote during playback to activate manual  
tracking.  
Previous  
program  
recorded  
Next  
program  
recorded  
2nd next  
B Press CH + and to eliminate the noises. Press it briefly for a  
fine adjustment, or press and hold for a coarse adjustment.  
C Press SP/EP on the Remote again to reactivate automatic  
tracking.  
Selecting monitor sound (HR-A57U only)  
— Audio Monitor  
Locating beginning of timer recordings  
— Instant Review  
While playing back a tape on which stereo sound or SAP sound is  
recorded, press A. MONITOR on the Remote. Each time you press  
the button, sound changes.  
Press REVIEW on the Remote after ensuring that the VCR is in the  
timer recording standby mode.  
HI-FI: Normally select this. Hi-Fi sound is played back.  
HI-FI L: Sound on the left Hi-Fi channel is played back.  
HI-FI R: Sound on the right Hi-Fi channel is played back.  
NORM: Sound on the normal track is played back.  
NORM HI-FI: Both sounds on the Hi-Fi track and normal track are  
mixed and played back.  
The VCR turns on, and rewinds to the index code indicating the  
beginning of the last timer-recorded program, then begins  
playback automatically.  
You can access a program of 2 to 9 index codes away from the  
current position on the tape. If, for example, you have  
5 programs recorded and you want to watch the third one, press  
REVIEW three times.  
NOTE:  
The above indication appears when “SUPERIMPOSE” is set to  
“ON”, though the monitor sound changes in sequence.  
The Instant Review function will also operate if the VCR is  
turned on.  
Automatic operations after rewinding  
— Next Function Memory  
Skipping unwanted portions  
— Skip Search  
The Next Function Memory “tells” the VCR what to do after  
rewinding is complete. Ensure that the VCR is in stop mode.  
For Automatic Playback Start  
Press SKIP SEARCH on the Remote once to 4 times during  
playback. Each press initiates a 30-second period of high speed  
playback (up to 2 minutes). When the specified portion of the tape  
is skipped, normal playback resumes automatically. To return to  
normal playback during Skip Search, press PLAY (4).  
Press REW (3), then press PLAY (4) within 2 seconds.  
For Automatic Power Off  
Press REW (3), then press POWER within 2 seconds.  
For Automatic Timer Standby  
Press REW (3), then press TIMER within 2 seconds.  
NOTE:  
It is not possible to select the Automatic Timer Standby function if  
the cassettes record safety tab is removed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recording Features  
Recording  
It may be unlawful to record or play back copyrighted material  
without the consent of the copyright owner.  
Specifying recording length  
— Instant Timer Recording (ITR)  
Accidental erasure prevention  
To prevent accidental recording on a  
recorded cassette, remove its record  
safety tab. To record on it later, cover  
During recording, press REC (7) on the VCR repeatedly until the  
recording length you want appears on the display panel. The  
record indicator () on the display panel starts blinking.  
Each time you press the button, recording length increases in  
30-minute intervals (up to 6 hours).  
the hole with adhesive tape.  
Record safety tab  
The VCR shuts off after recording is finished.  
To cancel an ITR, press STOP (8) on the Remote or STOP/EJECT  
(0) on the VCR.  
Basic Recording  
A Load a cassette  
Watching one program while recording another  
Make sure the record safety tab is intact. If not, cover the hole  
with adhesive tape before inserting the cassette.  
The VCR turns on, and the counter is reset, automatically.  
During recording…  
If you connect the TV and the VCR only using the RF  
connection to view pictures from the VCR, press TV/VCR on the  
Remote so that VCR mode indicator goes off from the display  
panel. (The TV broadcast being recorded disappears.)  
If you are using the AV connection to view pictures from the  
VCR, change the TVs input mode from AV to TV.  
Then, select the channel you want to watch, on the TV.  
B Select recording channel  
On the Remote  
Press CH+/– or the Number keys.  
On the VCR  
Press PAUSE[CH]. The channel display on the  
display panel starts blinking. While the display is  
blinking, press FF[CH+] or REW[CH–] to select  
channel. After about 5 seconds, the channel display  
stops blinking.  
Second Audio Recording (HR-A57U only)  
This VCRs built-in MTS decoder enables reception of  
Multichannel TV Sound broadcast. To record a SAP program  
received, set 2ND AUDIO RECORDto ON.  
NOTES:  
You can select channel in the stop mode,  
recording pause mode or during rewind/fast-  
forward high-speed search.  
If no cassette is loaded, or during recording pause  
mode, you can select channel only by pressing  
FF[CH+] or REW[CH–].  
If you connect the TV and the VCR only using the  
RF connection, press TV/VCR on the Remote so  
that the VCR mode indicator lights on the display  
panel, to view the program to be recorded.  
C Set tape speed  
Press SP/EP (p).  
D Start recording  
On the VCR, press REC (7). Or on the Remote, while holding REC  
(7), press PLAY (4).  
During recording  
Pause recording  
Press PAUSE (9).  
Press PLAY (4) to resume recording.  
You can select channel in the recording pause mode.  
Stop recording  
Press STOP (8) on the  
Remote.  
OR Press STOP/EJECT (0) on  
the VCR.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C Press OK or PROG..  
If PROGRAM NOT COMPLETED PROGRAM OVERLAP”  
appears, see Program overlap warning display.  
Timer Recording  
Up to 8 timer recording programs can be made using Express  
timer programing method as far as a year in advance. Remember,  
the clock must be set before you can program the timer.  
D Press TIMER. The VCR turns off automatically and #is  
displayed on the display panel.  
NOTES:  
If all the 8 programs have already been set, “PROGRAM FULL”  
or “Full” appears on the TV screen or the display panel.  
After timer recording is completed, the VCR turns off  
automatically.  
You can program the timer recording while a regular recording  
is in progress; the menu screens will not be recorded.  
To timer-record cable or satellite channels, be sure to keep the  
cable box or DBS receiver turned on with the correct channel  
selected.  
To use the VCR while it is in timer  
recording standby mode  
Press TIMER, then press POWER. After you use the VCR, press  
TIMER again to put the VCR into timer recording standby mode.  
Even if a power failure occurs, the VCR keeps your timer  
programs. However, the clock time, channel settings, and other  
menu settings are lost. As a result, when the power is supplied  
again to this VCR after the power failure, this VCR starts the  
Plug&Play setting automatically to restore the clock time and  
channel setting. If the clock time and channel setting are  
restored correctly, each timer program you have made will start  
at its start time unless its end time has elapsed.  
Checking, canceling or changing  
program settings  
A Disengage timer  
Press TIMER, then press POWER.  
When AUTO TIMERis set to ON, you do not have to press  
TIMER.  
B Access Program Check screen  
Press PROG. CHECK.  
PR START STOP CH DATE  
Express Timer Programing  
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24  
10:00A 10:45 40 12/25  
11:30P  
1:00 125 12/25  
Load a cassette with the record safety tab intact. The VCR turns  
on, and the counter is reset, automatically.  
PRESS (CHECK) TO NEXT  
PROGRAM 1  
C Access Program screen  
Press PROG. CHECK again. Each time you  
press PROG. CHECK, the next programs  
Program screen appears.  
START  
8:00 PM  
DATE  
STOP  
10:00 PM  
CH  
12/24/00  
12 SP  
PRESS (CANCEL) TO CANCEL  
PRESS (CHECK) TO NEXT  
D Cancel or change program setting  
To cancel a program, press CANCEL when the Program screen  
you do not want is shown.  
To change a program, press the appropriate button: START+/–,  
STOP+/–, DATE+/–, CH+/–, and/or SP/EP (p) when the  
Program screen on which you want to make changes is shown.  
E Return to normal screen  
Press PROG. CHECK repeatedly until no Program screen is  
shown.  
F Reengage timer recording standby mode  
Press TIMER. The VCR turns off automatically and #is  
displayed on the display panel.  
When AUTO TIMERis set to ON, the timer recording  
standby mode automatically resumes when you turn off the  
VCR.  
A Press PROG. on the Remote to access the Program screen.  
B Press START+/–, STOP+/–, DATE+/–  
PROGRAM 1  
or CH+/– repeatedly to enter the start  
START  
– –:– –AM  
DATE  
STOP  
– –:– –AM  
CH  
time, stop time, date or channel.  
Press and hold START+/– or  
STOP+/– to increase the time in  
30-minute intervals.  
– –/– –/– –  
– – – SP  
PRESS (+/, SP/EP, 8=DAILY  
9=WEEKLY), THEN (0K)  
PRESS (PROG.) TO END  
To set the tape speed, press SP/EP  
(p).  
To timer-record daily (MondayFriday) or weekly serials,  
press DAILY (M-F) or WEEKLY. Pressing the button again  
makes the DAILYor WEEKLYdisplay disappear.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Timer Recording –  
Program overlap warning display  
Other Functions  
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”  
appears, you have another program overlapping the program you  
have just made. The Program Check screen appears and  
conflicting programs will start blinking.  
Checking tape position  
When you change the VCR operation  
mode from the stop mode to fast forward  
or rewind mode, or when you perform an  
Index Search or Instant Review, the tape  
PR START STOP CH DATE  
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24  
10:00A 10:45 40 12/25  
PROGRAM NOT COMPLETED  
PROGRAM OVERLAP  
11:30P  
1:00 125 12/25  
9:00P 10:00 10 12/24  
+
+
+
E
B
position indicator appears.  
The position of “q” in relation to “B”  
(Beginning) or “E” (End) shows you where  
you are on the tape.  
(
,
), THEN (  
)
(PROG.) : END  
Example:  
Program 1 (you have just made) and Program 4 overlap each  
other  
Set “SUPERIMPOSE” to “ON”.  
A Select program to modify  
PR START STOP CH DATE  
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24  
10:00A 10:45 40 12/25  
Changing display information  
Press rt, then press e.  
11:30P  
1:00 125 12/25  
You can only select one of the  
overlapping programs.  
If you do not mind this overlap, press  
PROG. to finish the timer program  
setting. The program starting earlier or  
9:00P 10:00 10 12/24  
Each time you press DISPLAY, the display panel  
shows the channel number and the clock time  
alternatively.  
(
,
), THEN (  
)
(PROG.) : END  
You can change display in the stop, recording or  
recording pause mode, or during rewind/fast-  
forward high-speed search.  
program with the lower program number will be recorded.  
When “SUPERIMPOSE” is set to “ON” and DISPLAY on the  
PROGRAM 4  
B Cancel or change program setting  
Remote is pressed, time counter will appear on the TV screen.  
START  
9:00PM  
DATE  
12/24/00  
SUN  
STOP  
10:00PM  
CH  
To cancel a program, press CANCEL when  
the Program screen you do not want is  
shown.  
To reset the time counter, press C. RESET on the Remote.  
10 SP  
PRESS (CANCEL) TO CANCEL  
PRESS (OK) TO CONFIRM  
PRESS (PROG.) TO END  
To change a program, press the  
appropriate button: START+/–, STOP+/–,  
DATE+/–, CH+/–, and/or SP/EP (p)  
Timer warning display  
A warning appears on the TV screen to tell  
when the Program screen on which you want to make changes is  
shown, then press OK.  
If the overlap is not yet solved, the conflicting programs will be  
shown on the Program check screen. Repeat the above steps  
again.  
you that the timer-recording is to start in  
–WARNING–  
TIMER RECORDING  
5 minutes if you are not in the timer  
TO START SOON  
recording standby mode at that time. Press  
(CANCEL)  
TIMER to put the VCR into timer recording  
standby mode. To clear the display, press  
CANCEL on the Remote.  
Function settings  
You can use the other useful function settings on the Function Set  
screen.  
MAIN MENU  
A Access Main Menu screen, then  
FUNCTION SET  
Function Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to  
“FUNCTION SET”, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Select Function  
Press rt to move the highlight bar (arrow) to the function you  
want to set.  
HR-A57U  
FUNCTION  
PREVIOUS PAGE  
BLUE BACK  
2ND AUDIO RECORD  
AUDIO MONITOR  
AUTO PICTURE  
ON  
AUTO  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
HI-FI  
PICTURE CONTROL  
AUTO TIMER  
SUPERIMPOSE  
AUTO SP EP TIMER  
VIDEO STABILIZER  
NEXT PAGE  
SELECT WITH (  
,
) AND (OK)  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
PRESS (MENU) TO END  
HR-A37U  
FUNCTION  
AUTO PICTURE  
ON  
AUTO  
OFF  
ON  
OFF  
OFF  
ON  
PICTURE CONTROL  
AUTO TIMER  
SUPERIMPOSE  
AUTO SP EP TIMER  
VIDEO STABILIZER  
BLUE BACK  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
Download from Www.Somanuals.com. All Manuals Search And Download.  
– Other Functions –  
C Change setting  
VIDEO STABILIZER — ON/OFF  
When this function is set to ON, you can automatically correct  
vertical vibrations in the picture when playing back unstable  
recordings made on another VCR.  
Press OK or e. The default setting is bold in the following table.  
Press MENU to return to normal screen.  
NOTE:  
AUTO PICTURE ON/OFF  
To watch recordings with close-caption or when you finish  
viewing a tape, set this function to “OFF”.  
When this function is set to ON, this VCR checks the condition  
of the tape in use during playback, and compensates to provide  
the highest-possible playback pictures.  
BLUE BACK ON/OFF  
When this function is set to ON, the TV screen becomes all blue  
in the following cases:  
When receiving a channel not in use.  
When stopping playback.  
PICTURE CONTROL AUTO(NORM)/EDIT/SOFT/SHARP  
This function helps you to adjust the playback picture quality  
according to your preference.  
AUTO (NORM): Normally select this. Picture quality is adjusted  
automatically. When AUTO PICTUREis OFF, NORMwill  
appear instead of AUTO.  
NOTE:  
When you want to receive an unstable channel with poor signals,  
set this function to “OFF”.  
EDIT: Minimizes picture degradation during editing (recording and  
playback).  
SOFT: Reduces image coarseness when viewing overplayed tapes  
containing much noise.  
SHARP: Clearer, sharper-edged picture when viewing images with  
much flat, same-colored surfaces such as cartoons.  
2ND AUDIO RECORD — ON/OFF (HR-A57U only)  
When this function is set to “ON”;  
If a SAP program is received, the SAP audio is recorded on both  
the normal and Hi-Fi tracks. The main audio is not recorded.  
If a non-SAP program is received, the main audio is recorded on  
both the Hi-Fi and normal tracks.  
NOTE:  
Select “EDIT” when you are editing tapes. After you finish editing  
the tapes, select “AUTO”.  
When this function is set to “OFF”, the SAP audio cannot be  
recorded.  
NOTES:  
AUTO TIMER — ON/OFF  
When this function is set to “ON”:  
When the channel is changed on the VCR;  
The “STEREO” indication appears on the screen for about  
5 seconds if the program is a stereo broadcast.  
The “SAP” indication appears on the screen for about 5 seconds  
if the program is a SAP broadcast.  
Both indications appear when a stereo program is accompanied  
by SAP sound.  
The timer recording standby mode is automatically engaged when  
the VCR is turned off. It is temporarily canceled when the VCR is  
turned on. You do not have to press TIMER to engage or disengage  
the timer recording standby mode.  
When this function is set to “OFF”:  
You have to press TIMER to engage or disengage the timer  
recording standby mode.  
AUDIO MONITOR HI-FI/HI-FI L/HI-FI R/NORM/MIX  
(HR-A57U only)  
SUPERIMPOSE ON/OFF  
This VCR can record two sound tracks simultaneously (normal  
and Hi-Fi) on a Hi-Fi stereo tape. You can select the sound track(s)  
to listen to while playing back a Hi-Fi stereo tape. In addition,  
when playing back a prerecorded tape containing two separate  
audio programs on the Hi-Fi tracks, you can choose either one by  
selecting either HI-FI Lor HI-FI R.  
HI-FI: Normally select this. Hi-Fi sound is played back.  
HI-FI L: Sound on the left Hi-Fi channel is played back.  
HI-FI R: Sound on the right Hi-Fi channel is played back.  
NORM: Sound on the normal track is played back.  
MIX: Both sounds on the Hi-Fi track and normal track are mixed  
and played back.  
When this function is set to ON, various VCR status information  
(on-screen display) appears on the screen.  
NOTE:  
When you use this VCR as the playback VCR for editing a tape, be  
sure to set this function to “OFF”; otherwise, the VCR status  
information (on-screen display) will be recorded on the edited  
tape.  
AUTO SP]EP TIMER — ON/OFF  
When this function is set to ON, the VCR automatically  
switches to EP mode to allow complete recording if there is not  
enough tape to record the entire program while timer-recording in  
SP mode.  
NOTES:  
While playing back a monaural tape, sounds on the normal  
track will be heard regardless of this setting.  
If RF connection is used for viewing pictures on the TV, sound  
will be monaural even though you select “HI-FI”.  
You can also use the A. MONITOR button on the Remote to  
select the desired monitor sound.  
For Example, Recording a program of 140 minutes in length onto  
a 120-minute tape  
Approximately 110 minutes  
Approximately 30 minutes  
SP mode  
EP mode  
NOTES:  
If you have programed the VCR to timer-record 2 or more  
programs, do not use this function, but change the tape speed  
manually during timer programing.  
There may be some noise and sound disturbance where the tape  
speed switches from SP to EP mode on the tape.  
This function is not available during ITR (Instant Timer  
Recording), and will not work properly on the following tapes:  
T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                            
                            
Editing  
Specifications  
You can use your VCR as the playback or recording VCR. You can  
use a camcorder as the playback VCR and your VCR as the  
recording VCR. Refer also to the other components’ instruction  
manuals for connection and its operations.  
GENERAL  
Power requirement  
Power consumption  
[HR-A57U]  
Power on  
: AC 120 Vd, 60 Hz  
A Make connections  
Example: When using this VCR as the playback VCR  
: 18 W  
: 2.0 W  
Power off  
[HR-A37U]  
Power on  
Power off  
This VCR (for playback)  
To AUDIO/VIDEO OUT  
: 16 W  
: 2.0 W  
Temperature  
Operating  
Storage  
Operating position  
: 5°C to 40°C (41°F to 104°F)  
: –20°C to 60°C (–4°F to140°F)  
: Horizontal only  
Dimensions (W x H x D) : 360 mm x 94 mm x 247 mm  
(14-3/16" x 3-3/4" x 9-3/4")  
Audio/video cable  
(not supplied)  
Weight  
: 3.0 kg (6.6 lbs)  
Format  
: VHS NTSC standard  
Maximum recording time  
SP  
EP  
: 210 min. with ST-210 video cassette  
: 630 min. with ST-210 video cassette  
To audio/video input  
VIDEO/AUDIO  
Another VCR (for recording)  
Signal system  
:
NTSC-type color signal and EIA  
monochrome signal, 525 lines/  
60 fields  
When using this VCR as the recording VCR, connect this VCRs  
audio/video input connectors to the audio/video output  
connectors on the other VCR. If the playback VCR is monaural,  
connect the audio output connector on the playback VCR to the  
left audio input connector on this VCR.  
Recording/Playback  
system  
Signal-to-noise ratio  
Horizontal resolution  
Frequency range  
[HR-A57U]  
:
DA-4 (Double Azimuth) head helical  
scan system  
45 dB  
:
:
230 lines  
B Load cassettes  
Insert the playback cassette into the playback VCR and the  
cassette to be recorded on into the recording VCR.  
Normal audio  
Hi-Fi audio  
:
:
70 Hz to 10,000 Hz  
20 Hz to 20,000 Hz  
[HR-A37U]  
Normal audio  
Input/Output  
C Select input mode on recording VCR  
:
:
70 Hz to 10,000 Hz  
RCA connectors (IN x 2, OUT x 1)  
Select the correct external input on the recording VCR.  
On this VCR (when using this VCR as the recording VCR);  
Select “F-1” — when connecting the other VCR to the audio/video  
input connectors on the front panel.  
TUNER  
Press AUX or CH+/– on the Remote. You can select the input  
mode also by pressing PAUSE[CH], and then FF[CH+] or  
REW[CH–] on the VCR. See step B in “Basic Recording”.  
Tuning system  
Channel coverage  
VHF  
UHF  
CATV  
RF output  
: Frequency-synthesized tuner  
: Channels 2–13  
: Channels 14–69  
: 113 Channels  
D Select edit mode  
Set the edit mode to “ON” for the VCRs if such a mode is  
equipped.  
: Channel 3 or 4 (switchable; preset to  
Channel 3 when shipped) 75 ohms,  
unbalanced  
On this VCR, set “PICTURE CONTROL” to “EDIT”.  
E Start playback  
Press PLAY (4) on the playback VCR.  
F Start recording  
Press REC (7) on the recording VCR.  
TIMER  
Clock reference  
:
:
Quartz  
Program capacity  
1-year programmable timer/  
8 programs  
Memory backup for timer is not supported.  
ACCESSORIES  
Provided accessories  
: RF cable (F-type),  
Infrared remote control unit,  
“AA” battery x 2  
Specifications shown are for SP mode unless specified otherwise.  
E. & O.E. Design and specifications subject to change without  
notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOR SERVICING (Only in U.S.A.)  
HOW TO LOCATE YOUR JVC SERVICE CENTER  
TOLL FREE: 1-800-537-5722  
Dear Customer,  
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the  
unit. In the event that repair is necessary, or for the address nearest your location within the Continental United States,  
retain your Bill of Sale for Warranty Service.  
— JVC  
JVC SERVICE & ENGINEERING  
COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and  
production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC  
is world famous. The JVC service and engineering organization stands behind our products.  
NATIONAL HEADQUARTERS  
JVC SERVICE & ENGINEERING COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
10 New Maple Avenue  
Pine Brook, NJ 07058-9641  
ACCESSORIES  
Don’t service the product yourself.  
To purchase accessories for your JVC product, you  
may contact your local JVC Dealer.  
From the 48 Continental United States call toll free:  
CAUTION  
To prevent electrical shock, do not open the cabinet.  
There are no user serviceable parts inside.  
Please refer to qualified service personnel for repairs.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY (Only in U.S.A.)  
LIMITED WARRANTY  
CONSUMER VIDEO 1-90  
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL  
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail  
purchase for the period as shown below. (“The Warranty Period”)  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN  
COMMONWEALTH OF PUERTO RICO.  
WHAT WE WILL DO:  
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and  
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for  
replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC  
authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered  
on an in-home basis.  
WHAT YOU MUST DO FOR WARRANTY SERVICE:  
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service  
center, please call toll free: (800) 537-5722.  
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of  
sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be  
given to you by the toll-free number.  
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.  
WHAT IS NOT COVERED:  
This limited warranty provided by JVC does not cover:  
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,  
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service,  
or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with,  
defaced or removed;  
2. Initial installation and installation and removal for repair;  
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;  
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;  
5. Signal reception problems and failures due to line power surge;  
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;  
7. Accessories;  
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);  
There are no other express warranties except as listed above.  
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED  
TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.  
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER  
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES,  
RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS  
WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.  
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts,  
so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other  
rights which vary from state to state.  
JVC COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
1700 Valley Road  
Wayne, New Jersey 07470  
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF  
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION  
PACKAGED WITH EACH REFURBISHED PRODUCT.  
For customer use:  
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information  
for future reference.  
Model No.:  
Serial No.:  
Purchase date:  
Name of dealer:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

InFocus Projector IN20 User Manual
Jenn Air Range JGR8895BD User Manual
Johnson Hardware Door 1521 User Manual
JVC Camcorder LYT2044 001C M User Manual
JVC Car Stereo System GET0260 015A User Manual
JVC Projector LXD700U User Manual
JVC Universal Remote RM LP25U User Manual
KitchenAid Blender 5KHB2571 User Manual
KitchenAid Ice Maker KUIC15PRTS1 User Manual
Kodak Digital Camera CX7300 User Manual