ENGLISH
VIDEO CASSETTE RECORDER
HR-S6960AA
INSTRUCTIONS
LPT0799-001A
CONTENTS
SAFETY FIRST
SAFETY FIRST............................................................................... 1
Buttons, Connectors and Indicators ................................................ 3
Basic Connections.......................................................................... 4
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING:DANGEROUS VOLTAGE INSIDE
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Initial Settings.............................................................................. 5
Video Channel Set.................................................................. 5
Auto Set Up............................................................................ 5
Clock setting........................................................................... 6
CAUTION
Ⅲ When you are not using the recorder for a long period of
time, it is recommended that you disconnect the power cord
from the mains outlet.
Playback ...................................................................................... 6
Recording..................................................................................... 8
Ⅲ Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the mains outlet prior to
connecting or disconnecting any signal lead or aerial.
Timer Recording.......................................................................... 10
G-CODETM/SHOWVIEWTM System Setup ................................... 10
G-CODETM/SHOWVIEWTM Timer Programming......................... 11
Express Timer Programming.................................................. 11
24H Express Timer Programming.......................................... 12
Automatic Satellite Program Recording................................. 13
ATTENTION
1. This recorder can also receive SECAM colour television
signals for recording and playback.
2. Recordings made of SECAM television signals produce
monochrome pictures if played back on another video
recorder of SECAM standard, or do not produce normal
colour pictures if played back on another video recorder of
PAL standard.
3. SECAM prerecorded cassettes or recordings made with a
SECAM video recorder produce monochrome pictures when
played back with this recorder.
Program Navigation.................................................................... 14
Navigation............................................................................ 14
Other functions........................................................................... 15
Function Settings.................................................................. 15
Special Features.......................................................................... 17
Remote Control Functions.................................................... 17
IMPORTANT
Tuner Setting.............................................................................. 18
Ⅲ Please read the various precautions on this page before
installing or operating the recorder.
Ⅲ It should be noted that it may be unlawful to re-record pre-
recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast
or cable programme and in any literary, dramatic, musical, or
artistic work embodied therein.
Editing ....................................................................................... 20
Editing from a camcorder ..................................................... 20
Edit to or from Another Video Recorder................................ 20
System Connections .................................................................... 21
Connecting/Using a Stereo System ....................................... 21
Specifications.............................................................................. 22
Information on Multi-System Compatibility................................... 23
Troubleshooting .......................................................................... 25
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat
above 100°C or incinerate.
Replace battery with Panasonic (Matsushita Electric), Sanyo,
Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is incorrectly
replaced.
Ⅲ Dispose of used battery promptly.
Ⅲ Keep away from children.
Ⅲ Do not disassemble and do not dispose of in fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Buttons, Connectors and Indicators
CABLE/
SAT/DVD
VCR
TV
Front Panel
24H
EXPRESS #
Infrared beam
receiving window
Advanced
JOG dial
number keys
Cassette loading slot
1
Record 7
Pause 9
S-VHS ET
S-VIDEO/VIDEO/
AUDIO input
connectors
REC LINK
SP/LP/EP
Play 4
Rewind
Play 4
Stop/Eject 0
Fast Forward
Record 7
#
Pause 9
Stop 8
Display panel
Start Time
indicator
Stop Time indicator
“Timer” indicator
S-VHS
indicator
Instant REVIEW indicator
Play indicator
Channel/Clock/
Remain display
Mode display
(L-1, L-2, F-1,
S-1)
Record indicator
Buttons with a small dot on the left side of the name can also be
used to operate your TV (੬ 17).
Counter
display
Tape speed
SP/LP/EP
On-screen display
If you press ENTER (OK) on the remote control when “O.S.D.” is
set to “ON” (੬ 16), you can see the current recorder status on the
screen. To clear the on-screen display, press ENTER (OK) again.
The indications are not recorded even if the recorder is in the
recording mode.
To access covered connectors, pull and open the connector
cover.
Rear Panel
A Operation mode indicators
B Tape speed SP/LP/EP
C Colour system indicator (੬ 16)
D Tape direction
E Counter display
Mains power cord
F Tape remaining time indicator
G Audio mode display (੬ 8)
H Tape position indicator (੬ 8)
I Type of broadcast (੬ 10)
J Current day/month/year
K Clock display
(MONO)
L Channel position number/Aux. indicator (L-1, F-1, S-1 or S-2)
M Cassette loaded mark
Lithium battery compartment
N S-VHS ET indicator
(S-VHS ET: ON / S-VHS: OFF)
— 3 —
Download from Www.Somanuals.com. All Manuals Search And Download.
RF Connection
Basic Connections
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the ANT. IN connector on the
rear of the recorder.
A Check contents
C Connect the provided RF cable between the RF OUT
connector on the rear of the recorder and the TV’s aerial
connector.
Make sure the package contains all of the accessories listed in
“Specifications” (੬ 22).
B Situate recorder
Place the recorder on a stable, horizontal surface.
AV Connection
C Connect recorder to TV
If your TV is equipped with a AV Input Terminals connector,
perform AV connection to improve picture quality during tape
playback.
RF cable
(provided)
A Connect the aerial, recorder and TV as shown in the
illustration.
Aerial terminal
B Connect an optional AV cable between the AUDIO OUT/
VIDEO OUT connector on the rear of the recorder and the
AV-IN terminals.
S-video Connection
(allows you to make the most of the S-VHS picture performance.)
If your TV is equipped with a S-video input connector
A Perform “RF Connection” previously described.
B Connect the supplied S-video cable between the S-VIDEO
OUT connector on the rear of the recorder and the S-video
input connector on the TV.
C Connect an audio cable between the AUDIO OUT connectors
on the rear of the recorder and the audio input connectors on
the TV.
● Even if you are using audio/video cables to connect your
recorder to your TV, you must also connect it using the RF cable.
This will ensure that you can record one show while watching
another.
TV
aerial
cable
Back of TV
AV cable
(not provided)
AV-IN terminals
S-video cable
(provided)
D Connect recorder to mains
Plug the mains power cord into a mains outlet.
Mains power
cord
(MONO)
Back of recorder
AUDIO OUT/VIDEO OUT
Mains outlet
S-VIDEO OUT
Connect the power plug to an AC outlet before installing the lithium
battery. (੬ 2)
— 4 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Set Up
Initial Settings
The Auto Set Up function simplifies installation by guiding you
through the procedures of setting the language, clock and tuner
channels — simply follow the on-screen menus that appear.
Video Channel Set
Video channel (RF output channel) is the channel on which your
TV receives picture and sound signals from the recorder through
the RF cable. Before performing the following steps, make sure the
recorder’s power is off and there is no cassette inserted in the
recorder.
Before starting, make sure of the following:
● The TV aerial cable should be connected to the recorder.
● The recorder's mains power cord should be connected to a
mains outlet. (੬ 4)
● The “Video Channel Set” procedure should be done first and
the TV should be set to its AV mode (with AV or S-VIDEO
connection (੬ 4)) or video channel (with RF connection
(੬ 4)).
If you have connected the video recorder to your TV via the
provided RF cable only (RF connection)...
A Hold down 0 on the recorder
until the display panel shows the
following.
IMPORTANT
B Press PR + or – on the remote
control to set appropriate TV
system that matches the system of
TV being used (refer to the table
below).
● Don't press any buttons on the recorder or remote that are not
directly related to the step you are performing while Auto Set
Up is in progress.
● If you perform Auto Set Up successfully during installation,
there's no need to separately perform the Language Select,
Clock Set or Channel Set procedures, but if adjustments
become necessary they can be performed as follows:
–To change the selected language (੬ 6)
–To reset or adjust the time (੬ 6)
–To add/delete channels manually (੬ 19)
–To reset the tuner after moving to a different location
(੬ 18)
1:B/G 2:D/K 3:I 4:H
Major Countries/Areas
TV System
New Zealand, Kuwait, U.A.E., Indonesia,
Singapore, Thailand, Malaysia, Iran, Saudi
Arabia, Egypt, Morocco, Lebanon, Iraq
B/G
China, Mongolia, Russia
Hong Kong
D/K
I
A Set time
Press PUSH JOG rt to set the time, then
press OK or PUSH JOG e.
● Press and hold either button to delay or
advance the time by 30 minutes.
Australia
H
C Set your TV to UHF channel 36.
● If the two vertical white bars appear clearly on
the screen as shown on the right, press OK and
then go to step D.
[R/T]
B Set date
Press PUSH JOG rt to set the date, then press OK or PUSH JOG
● Ifthetwoverticalwhitebarsdonotappearclearly,
e.
pressOK andthenPR +or– tosettherecordertoavacantchannel
between 28 and 60 which is not occupied by any local station in
your area.
● Press and hold either button to change the date by 15 days.
C Set year
(Ex.) If channel 50 is available in your area...
Press PUSH JOG rt to set the year, then press MENU.
Then set your TV to UHF channel 50 and check if the two vertical
white bars appear clearly on the screen; if so, go to step D. If not,
re-set the recorder to another vacant channel and try again.
D Press OK to finish video channel set.
D Select TV system
Press PUSH JOG rt to place the pointer next to the appropriate
TV system (refer to the table on the left).
E Start auto channel set
If you have connected the video recorder to your TV via both the
provided RF cable and an AV cable (AV connection) or via the
provided RF cable, the provided S-Video cable and an Audio
cable (S-VIDEO connection)...
Press OK or PUSH JOG e.
AUTO CH SET
● Receivable channels in your area are
automatically assigned to the PR +/–
buttons, and non-receivable channels
are skipped.
● When Auto Set Up is completed, the
PLEASE WAIT
START
FINISH
A Hold down 0 on the recorder
I
I
I
I
I
I
I
I
I
I
I
I
– – – – – – –
until the display panel shows the
following.
lowest position number will appear on the front display panel. If
“SCAN COMPLETED–NO SIGNAL–” is displayed on the screen,
make sure that the aerial cable is connected to the recorder
properly and press OK on the remote control. The recorder will
try Auto Set Up again.
B Press OK, then press PR – until the
display panel shows the following.
Now the video channel is set to off
(– –).
C Press OK to finish video channel set.
● If Auto Set Up or Tuner Set has not previously been performed,
the Language Select screen appears and Auto Set Up function
takes place automatically.
— 5 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock setting
Playback
Turn on the TV and select the VIDEO channel or (AV mode).
Basic Playback
A Access Main Menu screen, then Intial
MAIN MENU
PROGRAMME NAVIGATION
Set screen
FUNCTION SET
Turn on the TV and select the video channel (or AV mode).
TUNER SET
Press MENU on the Remote. Press PUSH
INITIAL SET
JOG rt to place the pointer next to
A Load a cassette
“INITIAL SET”, then press OK or PUSH
[R/T]
[MENU] : EXIT
JOG e.
B Access Clock Set screen
INITIAL SET
Press PUSH JOG rt to place the pointer
CLOCK SET
G-CODE/SHOWVIEW SETUP
next to “CLOCK SET”, then press OK or
PUSH JOG e. The Clock Set screen
appears.
[R/T]
[MENU] : EXIT
Make sure the window side is up, the rear label side is facing you
and the arrow on the front of the cassette is pointing towards the
recorder.
● Do not apply too much pressure when inserting.
● The recorder turns on, and the counter on the on-screen display
is reset, automatically.
● Select the appropriate colour system with “PAL/MESECAM” and
“NTSC” in Function settings (੬ 16).
● If the cassette’s record safety tab has been removed, playback
begins automatically (੬ 8).
C Set Time, Date and Year
Press PUSH JOG rt to set the time, date
or year. Then press OK or PUSH JOG e.
● Press and hold either button to delay or
advance the time by 30 minutes.
● Press and hold either button to change
the date by 15 days.
Press MENU to return to normal screen.
NOTE:
● If the record safety tab is intact, the recorder check the tape
information for Programme Navigation. For details, refer to
“Navigation” (੬ 14).
If the year digits are automatically cleared, it is possible that you
have input February 29th in a non-leap year. Input the correct
data.
B Start playback
To make corrections any time during the process
Press OK or PUSH JOG e repeatedly until the item you want to
change blinks, then press PUSH JOG rt.
Press 4.
ATTENTION
In the search, still, slow-motion or frame-by-frame playback
mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour.
During playback
Stop playback
Press 8 on the remote
control.
OR Press 0 on the recorder.
Pause playback and view still picture
Press 9.
● Press 4 to resume normal playback.
Pause and Frame-by-Frame playback
Press 9 to pause, then press 6(or 9) repeatedly.
● Press 4 to resume normal playback.
Picture search
Press 3 or 5. Press 3 and 5 again to perform high-
speed search.
● Each time you press 3 or 5, the search speed changes
between low-speed and high-speed.
● Press 4 to resume normal playback.
Variable speed search (including slow-motion)
Press PUSH JOG w or e repeatedly.
● Press
4
to resume normal playback.
● Each time you press PUSH JOG
w
or e, the playback speed
changes. To decrease the speed during picture search, press the
opposite direction button repeatedly.
● During still picture, press and hold PUSH JOG
(or PUSH JOG to start reverse) slow motion playback. When
you release the button, still picture resumes. During still picture,
holding for more than 2 seconds also starts forward slow
motion playback. If you press again, still picture resumes.
● During slow motion playback, some noise may appear on the
screen. Press PR to eliminate the noise.
e
to start forward
w
9
9
r
/t
— 6 —
Download from Www.Somanuals.com. All Manuals Search And Download.
B Adjust tracking manually
Press PR +/– to adjust tracking.
● To return to automatic tracking, press p on the remote
control.
NOTE:
When a new tape is inserted, the recorder enters the automatic
tracking mode automatically.
Forward
Reverse
Reverse
Reverse
play
Reverse
slow
Slow
Normal
play
Forward
search
Repeat playback
search
motion
motion
Your video recorder can automatically play back the whole tape
100 times repeatedly.
-7, -5, -3
-1
-1/6
2, 3, 5, 7
1/6
1
When the tape is not running
Rewind/fast-forward
Press 3 or 5.
Eject the tape
A Start playback
Press 4.
Press 0.
B Activate repeat playback
Press 4 and hold for over 5 seconds, then release.
● The Play indicator (u) on the display panel blinks slowly.
● The tape plays 100 times automatically, and then stops.
● You can also eject the cassette when the recorder is turned off.
Turn off the recorder
Press 1.
C Stop playback
● Press 8 at any time to stop playback.
Playback Features
NOTES:
● Pressing 4, 3, 5 or 9 also stops Repeat Playback.
● Repeat Playback is not possible with a PAL tape recorded in EP
mode.
Index search
Your recorder automatically marks index
codes at the beginning of each recording.
This function gives you quick access to
any one of 9 index codes in either
direction.
Next function memory
The Next Function Memory “tells” the recorder what to do after
rewinding. Before continuing, ensure that the recorder is in the
Stop mode.
NOTE:
Before starting, make sure the recorder is in the Stop mode.
a– For Automatic Start Of Playback After Tape Rewind...
...press 3, then press 4 within 2 seconds.
b–For Automatic Power Off After Tape Rewind...
...press 3, then press 1 within 2 seconds.
c– For Automatic Timer Standby After Tape Rewind...
...press 3, then press # within 2 seconds.
— Activate Index Search
Press PUSH JOG w or e (2 or 6) on the remote control.
“2 1” or “6 1” is displayed on screen and search begins in
the corresponding direction.
● To access index codes 2 through 9, press PUSH JOG w or e
repeatedly until the correct index number is displayed.
NOTE:
It is not possible to select the Automatic Timer functions if the
cassette’s record safety tab is removed.
Ex.:To locate the beginning of B
from the current position,
press PUSH JOG w twice.
To locate the beginning of
D from the current position,
press PUSH JOG e once.
● When the specified index code
is located, playback begins
automatically.
Current position
Tape position indicator
The tape position indicator appears
on screen when, from the Stop mode,
you press 5, 3 or perform an
Index Search. The position of “8” in
relation to “0” (beginning) or “+”
(end) shows you where you are on the
tape.
Index number
Manual tracking
“O.S.D.” (੬ 16) must be set to
“ON”, or the indicator will not
appear.
Beginning
End
Your video recorder is equipped with automatic tracking control.
During playback, you can override this and adjust the tracking
manually by pressing the PR +/– buttons.
NOTE:
Depending on the type of tape used, there may be times when the
indication is not correct.
Skip search
A Override automatic tracking
Press p on the remote control to engage manual tracking.
— Skip over unwanted sections
Press 30 SEC 1 to 4 times during playback. Each press initiates a
30-second period of fast-motion playback. Normal playback
resumes automatically.
NOTE:
Before return to normal playback during a Skip Search, press 4.
— 7 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Review
Recording
Simply by pressing a single button, the recorder power comes on,
rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its safety
tab. To record on it later, cover the
hole with adhesive tape.
NOTE:
Before starting, make sure that the recorder is off and that the
Timer mode is disengaged.
Record safety tab
— Activate Instant Review
Basic Recording
Press REVIEW. The recorder power comes on and the recorder
searches for the index code indicating the start of the last timer-
recorded programme. Once it's found, playback begins
automatically.
Turn on the TV and select the video channel (or AV mode).
A Load a cassette
● The front display panel tells you how many programmes have
been recorded. If you have, for example, 3 programmes,
“REVIEW” and “3” appear and blink. To watch the first of the 3
programmes, press REVIEW three times. The recorder searches
and begins playback automatically. You can access a
programme as far as 9 index codes away from the current tape
position.
Insert a cassette with the record safety tab intact.
● The recorder power comes on automatically.
● The recorder checks the tape information for Programme
Navigation. For details, refer to “Navigation” (੬ 14).
● Select the appropriate colour system (੬ 16).
B Choose a programme
NOTE:
Press PR +/– or the number keys. Or push the JOG dial and turn it
Instant Review is not possible while the recorder is in the Timer
mode.
to the left or right to select the channel you wish to record.
C Set tape speed
Press p. Check the SP/LP/EP indicator on the recorder display
Soundtrack selection
panel to confirm the selected tape speed.
Your video recorder is capable of recording three soundtracks (HI-
FI L, HI-FI R and NORM) and will play back the one you select.
D Start recording
Press and hold 7 and 4 on the remote control, or press 7 on the
recorder.
● B.E.S.T. takes place at the beginning of each first SP and first LP
(or EP) recording after inserting the cassette (੬ 15).
During Playback
Pressing AUDIO on the remote control changes the soundtrack
being played back as follows:
Track
Use
During recording
On-screen Display
Pause recording
HI FI
For Hi-Fi stereo tapes
L
L
R
Press 9.
● Press 4 to resume recording.
● You can select channel in the recording pause mode.
HI FI
For main audio of Bilingual
tapes
Stop recording
HI FI
For sub audio of Bilingual
tapes
R
Press 8 on the remote
control.
OR Press 0on the recorder.
NORM
For audio-dubbed tapes
HI FI
NORM
For audio-dubbed tapes
NOTE:
When recording in NTSC, if EP is selected, recording will always
be done in the VHS mode even if an S-VHS cassette is used.
NOTES:
● “HIFI L
R” should normally be selected. In this mode, Hi-Fi
Recording Resume Function
stereo tapes are played back in stereo, and the NORM track is
played back automatically for tapes with only normal audio.
● For instructions on recording stereo and bilingual programmes,
refer to page 10.
● “O.S.D.” must be set to “ON” or the on-screen displays will not
appear (੬ 16)
If there is a power outage during recording (or Instant Timer
Recording or timer recording), the recording will resume
automatically when power is restored to the recorder unless the
recorder's memory backup has expired.
— 8 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Super VHS ET (S-VHS ET)
Recording Features
— Recording on VHS cassettes with S-VHS quality
Record one programme while watching another
You can record in SP mode on VHS cassettes with S-VHS picture
quality. You can play back a tape recorded using the S-VHS ET
function on most of S-VHS recorders and of VHS recorders
equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice
some recorders are not compatible with the S-VHS ET function.)
● You can activate the S-VHS ET function only before you start
recording on a VHS cassette.
— Select channel to watch
Once recording is in progress, all you need to do is to set the
channel controls on the TV for the station you wish to view.
● The programme selected with the TV's channel controls appears
on the TV screen while the one selected with the PR +/– buttons
is recorded on the tape.
● Before recording, make sure that “B.E.S.T.” is set to “ON”
(੬ 15).
Elapsed recording time indication
You can check the exact time of a recording.
Engage the S-VHS ET mode.
Press S-VHS ET on the recorder. You can check the current setting
(“S-VHS ET : ON” or “S-VHS ET : OFF”). If “S-VHS ET : OFF”
appears on the TV screen, press S-VHS ET again in about 5
seconds to set it to “ON”.
A Set counter display
Press – –:– – until a counter reading appears on the display panel.
● By pressing the – –:– – button, you can change the display to
show the counter reading, channel position*, clock time or tape
remaining time.
● The S-VHS indicator lights up on the front display panel.
* Channel position is not displayed during playback.
NOTES:
● You cannot activate the S-VHS ET function...
... while recording is in progress.
B Reset counter
Press 0000 before starting recording or playback.
● The counter is reset to “0:00:00” and shows the exact elapsed
time as the tape runs.
... while timer-recording or Instant Timer Recording (੬ 9) is in
progress.
... while B.E.S.T. (੬ 15) is in progress.
● The S-VHS ET function does not work...
... with S-VHS cassettes.
Instant Timer Recording (ITR)
... with recordings in LP/EP mode.
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the recorder off after
recording is finished.
● To keep the highest quality recording and playback pictures
over a long period of time, S-VHS recording on S-VHS cassettes
is recommended .
● Use of high grade tapes is recommended for S-VHS ET
recordings. On some tapes, picture quality will not improve
even if the S-VHS ET function is used. Check the recording
quality before you start important recordings.
● While playing back a tape recorded using the S-VHS ET function
on some recorders, noise may appear. (If playback picture
becomes blurred or interrupted, use a cleaning cassette.)
● In the high-speed search, still, slow-motion or frame-by-frame
playback modes (੬ 6), noise may appear. If these modes are
performed frequently on a tape recorded using the S-VHS ET
function, the tape may be damaged and the picture may be
deteriorated.
A Start recording
Press 7 on the recorder.
B Engage ITR mode
Press 7 again. “o” blinks and 0:30 appears on the front display
panel.
C Set recording duration
If you want to record for more than 30 minutes, press 7 to extend
the time. Each press extends recording time by 30 minutes.
NOTE:
You can only perform ITR using the 7 button on the recorder’s
front panel.
Tape Remaining Time
— Display remaining time
Press – –:– – until the time remaining on the tape appears.
● The display panel shows the tape remaining time with “– –:– –”
displayed.
● By pressing the – –:– – button, you can change the display to
show the counter reading, channel position*, clock time or tape
remaining time.
* Channel position is not displayed during playback.
NOTE:
Depending on the type of tape used, there may be times when the
tape remaining time reading may not appear right away, or is not
correct. “– –:– –” may sometimes appear, or the display may blink
on occasion.
— 9 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving stereo and bilingual programmes
Timer Recording
Up to 8 timer recording programs can be made using G-CODE/
SHOWVIEW timer programing or Express timer programing method
as far as a year in advance. Remember, the clock must be set
before you can program the timer.
Your recorder is equipped with a Sound-Multiplex decoder (A2)
and a Digital stereo sound decoder (NICAM) as well, making
reception of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
Type of broadcast being received
On-screen display
NOTES:
● If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
A2 Stereo
A2 Bilingual
ST
BIL.
● After timer recording is completed, the recorder turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
(none)
ST NICAM
BIL. NICAM
NICAM
● To listen to a stereo programme, press AUDIO until “HIFI L
R” appears on the screen.
● To listen to a bilingual programme, press AUDIO until “HIFI L
” or “HIFI R” appears on the screen (as required).
● To listen to the Standard (regular monaural) audio while
receiving a NICAM broadcast, press AUDIO until “NORM”
appears on the screen.
G-CODETM/SHOWVIEWTM System Setup
INFORMATION
G-CODE and SHOWVIEW are different trademarks used to represent
the same easy recording feature, but only the term G-CODE system
will be used in the instructions. If you use the SHOWVIEW system,
follow the same instructions listed for the G-CODE system.
NOTE:
“O.S.D.” must be set to “ON” or the on-screen displays will not
appear (੬ 16)
The G-CODE timer programming system eliminates the need to
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-CODE number for the
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
To record stereo and bilingual programmes (A2)
● Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed
L and R channel sound).
● Bilingual programmes are automatically recorded in bilingual
on the Hi-Fi audio track. The main soundtrack will be recorded
on the normal audio track.
You have to set “GUIDE PROG” numbers, which are assigned to
each station for purposes of G-CODE timer programming, for all
the stations stored in your recorder’s memory to get proper results.
Before G-CODE setup you must have performed the procedures of
Tuner Set and Clock Set.
To record NICAM stereo and bilingual programmes
The NICAM audio programme is recorded on the Hi-Fi audio
track, and the standard audio programme on the normal audio
track.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
NOTES:
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.
● If the quality of stereo sound being received is poor, the
broadcast may be received in monaural with better quality.
● Before playing back a programme recorded in stereo, or a
bilingual programme, refer to “Soundtrack selection” (੬ 8).
Guide Program Number Set
S-VHS (Super VHS), S-VHS ET or VHS Recording
Mode
A Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press PUSH JOG rt to place
the pointer next to “INITIAL SET”, then press OK or PUSH JOG e.
This VCR can record in S-VHS (Super VHS), S-VHS ET or VHS.
● To record in S-VHS:
B Access G-CODE/SHOWVIEW Setup screen
Set “S-VHS MODE” to “ON” (੬ 16). Then, insert a cassette
marked “S-VHS”. The S-VHS indicator lights up on the display
panel.
Press PUSH JOG rt to place the pointer next to “G-CODE/
SHOWVIEW SETUP”, then press OK or PUSH JOG e.
The S-VHS recording mode is selected.
C Input Guide Prog number
Press PUSH JOG rt or the Number
keys to select the Guide Program number
as shown in the TV listing, then press OK
or PUSH JOG e.
G-CODE/SHOWVIEW SETUP
● To record in S-VHS ET on a VHS cassette:
Set “S-VHS ET” to “ON” (੬ 9). Then, insert a cassette marked
“VHS”. The S-VHS indicator lights up on the display panel.
● To record in VHS:
GUIDE PROG
2
TV PROG
5
Insert a cassette marked “VHS”.
Set “S-VHS ET” to “OFF” (੬ 9).
[0-9] OR [R/T]: SELECT
[MENU] : EXIT
● To record in VHS on a S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up
on the display panel. Then, set “S-VHS MODE” to “OFF”
(੬ 16). The S-VHS indicator goes off.
D Input receiving channel number
G-CODE/SHOWVIEW SETUP
Press PUSH JOG rt or the Number
keys to select the number of the channel
on which the Guide Program number’s
broadcasts are received, then press OK
or PUSH JOG e.
GUIDE PROG
2
TV PROG
2
The VHS recording mode is selected.
[0-9] OR [R/T]: SELECT
[MENU] : EXIT
NOTE:
● If the satellite broadcast is received on
When playing back a tape that has been recorded in S-VHS or
S-VHS ET, the S-VHS indicator lights up on the display panel
regardless of the “S-VHS ET” (੬ 10) or “S-VHS MODE” (੬ 16)
setting.
your recorder's auxiliary channel (“L-1” or “F-1”), select “L-1”
or “F-1” for the channel position to which the satellite receiver is
connected.
● Repeat steps 3 and 4 as necessary.
E Return to normal screen
Press MENU on the remote control.
— 10 —
Download from Www.Somanuals.com. All Manuals Search And Download.
G-CODETM/SHOWVIEWTM Timer Programming
H Engage recorder’s timer mode
Press #. The recorder turns off automatically and “#” appears on
the display panel.
Before performing G-CODE/SHOWVIEW Timer Programming:
● Be sure to read “G-CODETM/SHOWVIEWTM System Setup”
(੬ 10).
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Turn on the TV and select the VIDEO channel (or AV mode).
● Select the appropriate colour system (੬ 16).
● To disengage the timer, press # again.
Satellite Tuner Users
To timer-record a satellite broadcast using the G-CODE system:
A Perform steps 1 – 8.
B Set the satellite tuner to the appropriate channel before the
selected programme begins.
C Leave the satellite tuner's power on.
With the G-CODE system , timer programming is greatly simplified
because each TV programme has a corresponding code number
which your recorder is able to recognise.
ATTENTION
Regarding Guide Program Number Set
A Access G-CODE/SHOWVIEW NO.
G-CODE/SHOWVIEW NO.
“G-CODE/SHOWVIEW SETUP” appears after performing step 3
if the Guide Program number for the G-CODE number you
entered has not been set.
screen
Press PROG.
● Press the number keys or PUSH
[0-9]
G-CODE/SHOWVIEW SETUP
[+/–] : EXPRESS PROGRAMING
JOG rt to input the channel
[PROG] : EXIT
position number on which your
GUIDE PROG
2
TV PROG
B Enter G-CODE number
Press the number keys to enter the
G-CODE number of a programme you
wish to record.
G-CODE/SHOWVIEW NO.
recorder receives that station, then
press OK or PUSH JOG e.
The G-CODE program screen
appears.
– –
1 2 3 4 5 6 7 8
[0-9] OR [R/T]: SELECT
[MENU] : EXIT
● If you make a mistake, press & and
input the correct number.
[0-9]
(Ex.) To timer-record a RTR
programme with the G-CODE system.
* If your recorder receives RTR on the channel position 2, press OK or
[&] : DELETE
[PROG] : EXIT
C Enter G-CODE programme screen
Press OK, and the G-CODE Programme
screen appears. (If you're just starting
out, “P1” appears.)
– PI –
NO. 123456789
PUSH JOG e after entering “2”.
START
21:00
STOP
22:00
SP
Express Timer Programming
Before performing the following steps:
DATE
25.04
: OK
TV PROG
1
[1] : TITLE
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Turn on the TV and select the VIDEO channel (or AV mode).
● Select the appropriate colour system (੬ 16).
IMPORTANT
Make sure the channel position number you wish to record is
displayed; if not, see “G-CODETM/SHOWVIEWTM System Setup” on
page 10 and set the Guide Program number for that G-CODE
number correctly.
A Access G-CODE screen
Press PROG.
● If the number you entered is invalid, “ERROR” appears on the
screen. Press & and input a valid G-CODE number.
● If the “G-CODE/SHOWVIEW SETUP” screen appears, see
“ATTENTION – Regarding Guide Program Number Set”
on page 11.
B Access programme screen
Press START +/–. (If you’re just starting
out, “P1” appears.)
D Set tape speed
Press p to set the tape speed.
[1] : TITLE
C Enter programme start time
E Access title edit screen
– P1 –
Press START +/– to enter the time you
Press the number keys “1”. The Title Edit
21:00
want recording to start.
25.04
21:00 PR.1
screen appears.
● Press and hold START +/– to move in
● You can access the Title Edit screen
only when “PROG. NAVIGATION” is
set to “ON”. (੬ 16)
[0-9] : SELECT LETTERS
[&] : DELETE
30-minute increments, or press and
[1] : TITLE
[Y/U] : CURSOR
release repeatedly to move 1 minute at
: OK
[PROG] : EXIT
a time.
F Enter programme title
– P1 –
D Enter programme stop time
Press STOP+/– to enter the time you want recording to stop.
● Press and hold STOP+/– to move in 30-minute increments, or
press and release repeatedly to move 1 minute at a time.
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering Character” on
page 15.
25.04
W
[0-9] : SELECT LETTERS
[&] : DELETE
[Y/U] : CURSOR
: OK
[PROG] : EXIT
E Enter programme date
G Return to normal screen
Press PROG or OK. “PROGRAM
COMPLETED” appears on the screen for about 5 seconds, then
normal screen appears. If “PROGRAM OVERLAPPED” appears on
the screen and “Err” on the display panel, see page 13.
● Repeat steps 1 – 7 for each additional programme.
Press DATE+/–. (The current date appears on screen. The date you
enter appears in its place.)
— 11 —
Download from Www.Somanuals.com. All Manuals Search And Download.
F Enter channel position
24H Express Timer Programming
Before performing the following steps:
● Insert a cassette with the safety tab in place. The recorder will
come on automatically.
● Select the appropriate colour system (੬ 16).
Press PR +/–.
21:00
25.12
22:00
G Set tape speed
Press p to set the tape speed.
1
[1] : TITLE
H Access title edit screen
– P1 –
You can programme a timer recording that starts within 24 hours.
Press the number keys “1”. The Title Edit
screen appears.
25.12
21:00 PR.1
A Access 24HR Express Timer Programme display
● You can access the Title Edit screen
only when “PROG. NAVIGATION” is
set to “ON”. (੬ 16)
Push 24H EXPRESS #. “ ” and start time start blinking on the
[0-9] : SELECT LETTERS
[&] : DELETE
display panel.
[Y/U] : CURSOR
: OK
[PROG] : EXIT
Programme start time indicator
I Enter programme title
– P1 –
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering character” on
page 15.
25.12
W
[0-9] : SELECT LETTERS
[&] : DELETE
[Y/U] : CURSOR
: OK
[PROG] : EXIT
J Return to normal screen
After confirming all information is
B Set programme start time
Turn the JOG dial to the left or right. Then, push the JOG dial.
correct, press PROG or OK. “PROGRAM COMPLETED” appears
on the screen for about 5 seconds, then normal screen appears. If
“PROGRAM OVERLAPPED” appears on the screen, see page 13.
● Repeat steps 1 – 10 for each additional programme.
“
” and start time start blinking on the display panel.
Programme start time indicator
K Engage recorder’s timer mode
Press #. The recorder turns off automatically and “#” appears on
the display panel.
● To disengage the timer, press # again.
NOTES:
● One click stop of the JOG dial changes the time in 5-minute
● To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 10, press WEEKLY (number
key “9”) for weekly serials or DAILY (number key “8”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the screen. Pressing the button again makes the
corresponding indication disappear.
intervals.
C Set programme stop time
Turn the JOG dial to the left or right. Then, push the JOG dial and
channel number will start blinking.
Programme stop time indicator
● You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on screen. To record the
extra programme, you must first cancel any unnecessary
programmes (੬ 13).
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
● One click stop of the JOG dial changes the time in 5-minute
intervals.
D Set channel position
Turn the JOG dial to the left or right. Then, push the JOG dial and
channel number will start blinking.
● You can cancel the setting at any time by pressing and holding
the JOG dial for more than 3 seconds. Repeat from the step 2.
E Engage recorder’s timer mode
Press 24H EXPRESS #.
The recorder turns off automatically and “#” appears on the
display panel.
— 12 —
Download from Www.Somanuals.com. All Manuals Search And Download.
When programme overlap each other
NOTES:
● If “Err” appears on the display panel, repeat the steps again.
● When a menu screen is shown, you cannot use 24H Express
Timer programming function. Press MENU to return to normal
screen, and try again.
If “PROGRAM OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
The Programme Check screen appears and conflicting
programmes will start blinking.
● You can use 24H Express Timer programming function also
when the recorder is turned off.
● For 24H Express Timer programming function, the program
overlap warning display does not appear even if some programs
overlap each other.
● In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00 10:00
10:00 10:45
11:30 13:00
3
2
1
24.04
25.04
25.04
PROGRAM OVERLAPPED
9:00 10:00 92 DAILY
[PROG] : EXIT
Example: Programme 1 (you have just made) and Programme 4
overlap each other.
Check, cancel and replace programmes
A Disengage timer mode
Press #, then press 1.
A Confirm the overlapping programmes
Overlapping programmes blink on the TV screen.
B Select the programme to modify
Press PUSH JOG rt, then press OK or PUSH JOG e.
B Access Program Check screen
Press ".
● You can only select one of the overlapping programmes.
NOTE:
If you do not mind this overlap, press PROG to finish the timer
programme setting. The programme with the lower programme
number will be recorded and the other one will not be recorded
correctly. If no changes are made for approximately 1 minute, the
recorder will return to the normal screen.
C Access Program screen
Press " again to check more
information. Each time you press ", the
next programme’s information appears.
C Cancel or change programme setting
To cancel a programme, press & when the Programme screen you
do not want is shown. “PROGRAM COMPLETED” appears on the
TV screen for about 5 seconds, then the normal screen appears.
[1] : TITLE
D Cancel or replace a programme
Press & to cancel a programme.
To change a programme, press the appropriate button: START +/–,
STOP+/–, DATE+/–, PR +/–, DAILY, WEEKLY and/or p when
the Programme screen on which you want to make changes is
shown, then press OK. “PROGRAM COMPLETED” appears on the
TV screen for about 5 seconds, then the normal screen appears.
To replace a programme, press the appropriate button: START +/–,
STOP+/–, DATE+/–, PR +/–, DAILY, WEEKLY and/or p.
● If you do not want to edit the programme title, skip steps
5
and
6.
E Access title edit screen
– P1 –
NOTE:
Press the number key “1”. The Title Edit
screen appears.
If the overlap is not yet solved, or another overlap occurs with the
timer programme setting after making the last correction on a
programme, the conflicting programmes will be shown on the
Programme Check screen again. Repeat the above steps again
until the overlap is solved.
24.12
8:00 PR.3
● You can access the title edit screen only
when “PROG. NAVIGATION” is set to
“ON”. (੬ 16)
[0-9] : SELECT LETTERS
[&] : DELETE
[Y/U] : CURSOR
: OK
[
] : EXIT
F Enter programme title
– P1 –
Press the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering character” on
page 15.
Automatic Satellite Program Recording
24.12
W
This facility allows you to automatically record a satellite program
which is timer-programmed on your external satellite receiver.
Connect a satellite receiver to the recorder's rear AUDIO/VIDEO
IN connectors and program the timer on the satellite receiver; the
recorder starts recording when the signals input from the satellite
receiver to the rear AUDIO/VIDEO IN connectors, and when there
is no input signals the recorder stops recording and the power
shuts off.
[0-9] : SELECT LETTERS
[&] : DELETE
[Y/U] : CURSOR
: OK
[
] : EXIT
G Return to normal screen
Press " as many times as necessary. If there are still some
programmes remaining, go on to step 8.
H Return to timer mode
Press #.
Before performing the following steps:
● Program the timer on the satellite receiver.
● Insert a cassette with the safety tab in place.
A Set tape speed
Press p to set the tape speed.
B Engage Auto Satellite Prog Rec mode
Press and hold REC LINK for about 2 seconds. The REC LINK
indicator lights up and the recorder turns off automatically.
● To disengage the Auto Satellite Prog Rec mode, press REC LINK.
● If the recorder's power is off, it is not possible to engage the
Auto Satellite Prog Rec mode.
— 13 —
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION
Program Navigation
● Be sure not to turn on the satellite receiver before the program
is executed; otherwise, the recorder will start recording when
the satellite receiver's power is turned on.
Navigation
Navigation Playback
● If you have connected another appliance other than a satellite
receiver to the rear AUDIO/VIDEO IN connectors, be sure
not to engage the Auto Satellite Prog Rec mode; otherwise,
the recorder will start recording when the connected
appliance's power is turned on.
Turn on the TV and select the VIDEO channel (or AV mode).
● Auto Satellite Prog recording and timer-recording cannot be
done at the same time.
This function is useful when you wish to quickly find out what
programmes you have recorded on a tape with this recorder. This
function allows you to select a programme to watch, and then
automatically searches for the start of the programme. (੬ 8)
NOTES:
● Auto Satellite Prog recording is only possible with the rear
AUDIO/VIDEO IN connectors.
A Load a recorded cassette
Insert a cassette recorded on this recorder.
● When the Auto Satellite Prog Rec mode is engaged or the
recorder's power is turned off after Auto Satellite Prog recording
is finished, the recorder will not enter the Timer mode even
though “AUTO TIMER” is set to “ON”.
● For timer programming of the satellite receiver, refer to the
instruction manual of the satellite receiver.
B Access Main Menu screen
Press MENU.
C Access Programme Navigation screen
MAIN MENU
Press PUSH JOG rt to place the pointer
PROGRAMME NAVIGATION
FUNCTION SET
next to “PROGRAMME NAVIGATION”,
TUNER SET
then press OK or PUSH JOG e.
● Auto Satellite Prog recording is not possible if your satellite
receiver does not have a timer.
INITIAL SET
● The REC LINK indicator blinks while Auto Satellite Prog
recording is in progress.
[R/T]
[MENU] : EXIT
● Pressing the recorder's 1 button while Auto Satellite Prog
recording is in progress turns off and recorder's power and
disengages the Auto Satellite Prog Rec mode.
● If there is more than one satellite program you wish to record
with Auto Satellite Prog Recording, it is not possible to set a
different tape speed for each; the tape speed selected in step 1
will apply to all the programs for Auto Satellite Prog recording.
● The B.E.S.T. (੬ 15) does not work while Auto Satellite Prog
recording is in progress.
D Select a programme
Press PUSH JOG rt to place the pointer
next to the programme you want to watch.
E Start playback
Press OK. “SEARCHING” appears on the
TV screen. Playback begins automatically
after the selected programme is located.
[R/T]
[&] : DELETE
[1] : TITLE
[MENU] : EXIT
● Depending on the type of satellite receiver, the recorder may not
record a short portion at the beginning of the program or may
record slightly longer than the actual length of the program.
● If you engage the Auto Satellite Prog Rec mode when the
satellite receiver's power is on, the recorder will not start Auto
Satellite Prog recording even though the button's light blinks.
When the satellite receiver shuts off once and is turned back on
again, the recorder starts recording.
● You can also record a program from your cable system in the
same way if the system has a timer and is connected to the
recorder's rear AUDIO/VIDEO IN connectors.
● When you press the recorder's REC LINK button to engage the
Auto Satellite Prog Rec mode, if the REC LINK indicator does
not light but instead blinks quickly even though your satellite
receiver's power is off, Auto Satellite Prog Recording will not
work properly with that satellite receiver*.
If this is the case, perform “Express Timer Programming”
(੬ pg. 11) to timer-record a satellite program.
* Some satellite receivers output signals even if the power is off. Auto
Satellite Prog Recording is not possible with those satellite receivers.
● After Automatic Satellite Program Recording, the number of
recorded programs will not be displayed on the front display
panel for the instant Review function (੬ 8).
Programme Navigation Screen
[R/T]
[&] : DELETE
[1] : TITLE
[MENU] : EXIT
A Recording date
B Recording start time*
C Station name*
* After entering the programme title (੬ 15), programme title
appears instead of the recording start time and station name.
D Currently selected programme
E Programme title*
* Before entering the programme title (੬ 15), recording start time
and station name appear instead of the programme title.
NOTES:
● You cannot edit programme title or delete tape data for the
cassette with the record safety tab removed.
● Programme Navigation is possible with the cassettes recorded
with this recorder only.
● Before recording, make sure the recorder’s clock is set correctly.
● Program Navigation may not work properly depending on the
tape being used.
● To record the programme information in this recorder’s memory,
you must continue to record each programme for over the
minimum recording time;
PAL
8 minutes for the SP mode
15 minutes for the LP mode
23 minutes for the EP mode
NTSC
5 minutes for the SP mode
15 minutes for the EP mode
● You can store programme information for up to 8 programmes
on one cassette. At maximum informations for 10 tapes can be
restored.
● The programme information is stored in this recorder’s memory.
If the memory in this recorder should ever be damaged and the
programme information lost, it is impossible to restore that
information.
— 14 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit programme title
Other functions
You can edit the the programme titles as you like.
Perform steps 1 to 3 of “Navigation Playback” on page 14
Function Settings
before continuing.
You can use the other useful function settings on the Function Set
screen
A Select programme
Press PUSH JOG rt to place the pointer
next to the programme you want to edit.
Turn on the TV and select the VIDEO channel (or AV mode).
A Access Main Menu screen, then
MAIN MENU
[R/T]
[1] : TITLE
[MENU] : EXIT
Function Set screen
PROGRAMME NAVIGATION
FUNCTION SET
TUNER SET
[&] : DELETE
Press MENU on the Remote. Press PUSH
JOG rt to place the pointer next to
“FUNCTION SET”, then press OK or PUSH
JOG e.
B Access title edit screen
Press the number key “1”. The Title Edit
screen appears.
INITIAL SET
– P1 –
27.02
22:00 F-1
[MENU] : EXIT
[0-9] : SELECT LETTERS
[&] : DELETE
B Select mode
[Y/U] : CURSOR
Press PUSH JOG rt to move the pointer to the function you
: OK
[PROG] : EXIT
want to set.
C Enter programme title
– P1 –
FUNCTION SET
● Press the number keys and PUSH JOG e
to enter characters, then press OK. For
details, refer to “Entering character” on
page 15.
B.E.S.T.
ON
AUTO
PREVIOUS PAGE
PROG. NAVIGATION
AUTO SP LP TIMER
VIDEO STABILIZER
S-VHS
27.02
W
PICTURE CONTROL
PAL/MESECAM
NTSC
ON
OFF
OFF
ON
AUTO
NTSC3.58
OFF
[0-9] : SELECT LETTERS
[&] : DELETE
AUTO TIMER
O.S.D.
NEXT PAGE
[R/T]
[MENU] : EXIT
ON
[Y/U] : CURSOR
: OK
[PROG] : EXIT
[R/T]
[MENU] : EXIT
D Return to normal screen
Press MENU.
C Change setting
Press OK or PUSH JOG e. The default setting is bold in the
Entering character
following table. Press MENU to return to normal screen.
Press the appropriate number key, then press PUSH JOG e to
enter each character.
Refer to the example below.
Ⅵ B.E.S.T. — ON / OFF
When B.E.S.T. (Biconditional Equalised Signal Tracking) system is
set to “ON”, the recorder checks the condition of the tape in use
during playback and recording, and compensates to provide the
highest-possible pictures. When B.E.S.T. works, “bESt” appears
blinking on the display panel. B.E.S.T. takes place whenever you
play back a tape or start recording after inserting a cassette.
NUMBER KEY
CHARACTER
. , / – + f ( ) 1
A B C 2 Ä À Á Â Ã Å Æ
D E F 3 È É Ë Ê
G H I 4 Î Ï Ì Í
1
2
3
4
5
6
7
8
9
0
NOTE:
The recorder checks the tape condition for about 7 seconds, then
starts recording. To make sure you record the desired scene or
programme completely, perform the following steps:
A Press and hold 7 and press 4 on the remote, or press 7 on
the recorder.
J K L 5
M N O 6 Ö Ô Ò Ó Õ Ø Ñ
P Q R S 7
B The recorder spends approximately 7 seconds assessing the
condition of the tape, then begins recording.
T U V 8 Ü Ù Û Ú
W X Y Z 9
0 I
Ⅵ PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT
This function helps you to adjust the playback picture quality
according to your preference. *The default setting is “AUTO”.
AUTO(NORM): Normally select “AUTO”. It automatically adjusts
the picture quality.
* When the B.E.S.T. function is set to “OFF” (੬ 15), you can only select
“NORM” instead of “AUTO”.
NOTES:
● If you make a mistake, press PUSH JOG we to select the
character, then enter the correct character.
● If you want to delete a character, press PUSH JOG we to select
the character, then press .
EDIT: Select when you dub tapes.
SOFT: Select when you want to soften the picture.
Delete tape data
NOTES:
● When you select “EDIT” or “SOFT”, the selected mode will not
change until you select again “AUTO”.
Perform steps 1 to 3 of “Navigation Playback” on page 14
before continuing.
● When you select “EDIT” to dub tapes, be sure to select “AUTO”
(or “NORM” when the B.E.S.T. function is set to “OFF”) after
you finish dubbing the tapes.
— Delete tape data
Press & for more than 3 second. All the
programme data on the tape are deleted,
then normal screen appears.
● It is impossible to delete each
programme information.
[R/T]
[&] : DELETE
[1] : TITLE
[MENU] : EXIT
NOTE:
When you delete the tape data, only the tape information is
deleted from the recorder’s memory. The actual recording on the
tape is not erased.
— 15 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Ⅵ PAL/MESECAM — AUTO / PAL / MESECAM
Usually set to “AUTO” mode. The appropriate colour system (PAL/
MESECAM) will be selected depending on the playback or
recording signals.
If the “AUTO” mode does not work properly, select either of the
following manual modes.
PAL: To record PAL signals, or playback a PAL tape.
MESECAM: To record SECAM signals, or playback a SECAM or
MESECAM tape.
Ⅵ AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the recorder automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire programme while timer-
recording in SP mode.
For example, recording a programme of 210 minutes in length
onto a 180 minute tape.
Approximately 150 minutes
Approximately 60 minutes
SP mode
LP mode
NOTES:
Total 210 minutes
● SECAM signals will always be recorded as MESECAM. Select
“AUTO” or “MESECAM” when recording SECAM signals.
● When playing back a SECAM tape, select “AUTO” or
“MESECAM”. The playback picture will always be
monochrome.
NOTES:
● If you have programmed the recorder to timer-record 2 or more
programmes, do not use this function, but change the tape
speed manually during timer programming.
● There may be some noise and sound disturbance where the tape
speed switches from SP to LP mode on the tape.
● This function is not available during ITR (Instant Timer
Recording), and will not work properly with any tapes longer
than E-180 or with some tapes of shorter lengths.
● If you perform timer recording with both this function and VPS/
PDC activated, and the programme goes beyond its originally
scheduled length, sometimes the programme cannot be
recorded in its entirety.
Ⅵ NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL
This function is to record NTSC signals or playback a NTSC tape.
NTSC3.58: To record NTSC signals or playback a NTSC tape.
NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43
tape.
NTSC]PAL: To playback a NTSC tape on PAL TV.
NOTES:
● The “NTSC]PAL” mode does not work during recording. In this
mode, NTSC signals will be recorded as NTSC3.58.
● The Menu screen is distorted during playing back a NTSC tape
on PAL TV. Stop playback and access the Menu screen again.
● In the “NTSC4.43” mode, with some TVs, on-screen displays
(Program screen, etc.) may roll up or down and there may be a
loss of colour, when this happens, select the NTSC3.58” mode.
Ⅵ VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibrations in the picture when playing back unstable
recordings made on another recorder.
NOTE:
To watch recordings with close-caption or when you finish
viewing a tape, set this function to “OFF”.
Ⅵ AUTO TIMER — ON / OFF
● When this function is set to “ON”:
The timer recording standby mode is automatically engaged when
the recorder is turned off. It is temporarily cancelled when the
recorder is turned on. You do not have to press # to engage or
disengage the timer recording standby mode.
Ⅵ S-VHS — 0N / OFF
You can determine which recording mode — either S-VHS mode
or VHS mode — is used for recording on S-VHS tapes.
● When this function is set to “ON”, you can record on S-VHS
tapes with S-VHS picture quality.
● When this function is set to “OFF”:
Press # to engage or disengage the timer recording standby mode.
● When this function is set to “OFF”, you can record on S-VHS
tapes with VHS picture quality.
NOTES:
Ⅵ O.S.D. — ON / OFF
When this function is set to “ON”, various recorder status
information (on-screen display) appears on the screen.
● S-VHS mode allows you to make high quality video recordings
with horizontal resolution of 400 lines, comparing with the 230
lines of resolution of conventional VHS recordings. To achieve
the highest quality picture we recommended to record in S-VHS
mode. (But remember that a conventional VHS recorder without
SQPB cannot play back S-VHS tapes recorded in S-VHS mode.
● S-VHS setting does not affect recording on VHS tapes.
Recording on VHS tapes is always performed in VHS mode
except when using S-VHS ET mode (੬ 9).
NOTE:
When you use the recorder as the source player for editing a tape,
be sure to set this function to “OFF”. Otherwise, the recorder
status information will be recorded on the edited tape.
Ⅵ PROG. NAVIGATION — ON / OFF
When you record a TV programme with this recorder, the recorder
automatically stores in its memory the recording date, start time
and station name. You can store these information for up to 8
programmes on one cassette. At maximum, information for 10
tapes can be stored. You can also enter the programme title when
performing “G-CODETM/SHOWVIEWTM Timer Programming” (੬ 11)
or “Express Timer Programming” (੬ 11). It is possible to store
these information only when “PROG. NAVIGATION” is set to
“ON” (default setting).
Set “PROG. NAVIGATION” to “OFF” if you don’t want to record
information on the programmes.
— 16 —
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Multi-brand Remote Control
Special Features
Your remote control can operate the basic functions of your TV
set. In addition to JVC TVs, other manufacturer's TVs can also be
controlled.
Remote Control Functions
Remote A/B Code Switching
A Turn on TV
Turn on the TV using the Power button on the TV or its remote
control.
The remote control is capable of controlling two JVC video
recorders independently; one set to respond to the remote
control's A code control signals and another set to respond to B
code control signals. The remote control is preset to send A code
signals because your video recorder is initially set to respond to A
code signals. You can easily modify your video recorder to
respond to B code signals.
B Set TV brand code
A Press and hold TV.
B Press the number keys to enter your unit’s brand code.
C Press OK, and release TV. Check if the TV's power goes off as it
should. If it does, try other operations (੬ step 2).
● Once you have set the remote control to operate the TV, you
don't have to repeat this step until you replace your remote
control's batteries.
A Set remote control code for remote control
A Press and hold VCR.
● Some TV brands have more than one code. If the TV does not
function with one code, try entering another.
B Press the number key “2”.
C Press OK, and release VCR.
C Operate TV
● The remote control now can transmit B code control signals.
First, press TV to set the remote control to TV mode, then press
one of the following buttons: 1, TV/VCR, TV PR +/–, ^
(TV Muting), TV %+/– (TV volume), and the number keys.
● For some brands, you must press OK after having pressed the
number keys to enter a channel number.
B Check remote control code for decorder
Press and hold 4 on the recorder for more than 5 seconds while
the recorder is turned off. The code currently set appears on the
display panel.
C Change code for recorder
IMPORTANT
Press any key on the remote control. The recorder now responds
to B code control signals.
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with
your TV, or in some instances, may have limited function
capability.
To control two recorders with the same remote control
You can control two JVC recorders by switching the remote
control code for the remote control between A and B (੬ step 1),
keeping two recorders to different control codes.
TV BRAND
NAME
CODE
TV BRAND
NAME
CODE
● To change only the remote control code for the remote control,
DO NOT perform steps 2 and 3.
JVC
01, 23, 24, 25
MITSUBISHI
MIVER
03
AIWA
36
22
02
34
17, 37
27
30
32
15
19
10
28
38
40
18
29
BEIJING
CCE
NEC
20
NOTE:
NOBLEX
NOKIA
PANASONIC
PEONY
PHILICO
PHILIPS
SAMSUNG
SANYO
SHARP
SONY
TCL
THOMSON
TOSHIBA
22
To set the recorder back to respond to A code signals, repeat the
same procedure as shown above except pressing number key "1"
instead of "2" in step 2 of 1.
CHANGHONG
DAEWOO
FERGUSON
FINLUX
31
04, 11
34, 38, 39
10, 17, 21
02, 42
12, 33, 34, 35
13, 16
06
FUNAI
Control Your TV Using Additional Buttons
Use the number keys, and the p button, & button or #
button to select the TV's channel.
● With televisions under Code 01, 02, 07, 08, 10, 11, 14, 20,
22, 23, 24, 25, 27, 33, 35, 38, 40 or 42, the p button
corresponds to the 1-digit/2-digit entry switching button
(often labelled – /– –) of your TV's remote control.
● With televisions under Code 01, 16, 28, 29, 34 or 39, the &
button corresponds to the 10 + button, and the # button
corresponds to the 20 + button of your TV's remote control.
GRADIENTE
GRUNDIG
HITACHI
ITT
07
JINXING
KONKA
LG/GOLDSTAR
41
26
08, 14
ATTENTION
The remote control can operate not only the video recorder but
also some of your TV, cable box, satellite receiver and DVD.
● To operate your video recorder, first press the VCR button to
set the remote control to the Video mode.
NOTE:
The way these buttons are used is determined by your TV. Use
these buttons as instructed for your TV's remote control.
● To operate your TV, first press the TV button to set the remote
control to the TV mode.
● To operate your satellite receiver, cable box or DVD, first
press the CABLE/SAT/DVD to set the remote control to the
satellite receiver, cable box or DVD mode.
— 17 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-brand Remote Control
For satellite receiver, cable box and DVD
Your remote control can operate the basic functions of your
satellite receiver, cable box or DVD.
Tuner Setting
Turn on the TV and select the VIDEO channel (or AV mode).
A Turn on unit
IMPORTANT
Turn on the cable box, satellite receiver or DVD using the Power
button on the unit or its remote control.
Perform the following steps only if auto channel set has not
been set correctly by Auto Set Up function (੬ 5) or if you have
moved to a different area or if a new station starts broadcasting
in your area.
B Set brand code
A Press and hold CABLE/SAT/DVD.
B Press the number keys to enter your unit’s brand code.
C Press OK, and release CABLE/SAT/DVD. Check if the unit's
power goes off as it should. If it does, try other operations (੬
step 2).
● Once you have set the remote control to operate the unit, you
don't have to repeat this step until you replace your remote
control's batteries.
Your recorder needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area so that
you can call them up with the PR +/– buttons without going
through any vacant channels.
Auto Channel Set
A Turn on the recorder
Press 1.
● Some brands have more than one code. If the unit does not
function with one code, try entering another.
C Operate unit
First, press CABLE/SAT/DVD to set the remote control to cable
box, satellite receiver or DVD mode, then press one of the
following buttons:
For satellite receiver and cable box . . .
1, TV PR +/–, number keys.
For DVD. . .
1, 4, 8, 9, 5, 3, w e (26) keys.
● For some brands, you must press OK after having pressed the
number keys to enter a channel number.
● To change the unit’s channels, press TV PR +/– or the number
keys. (The PR +/– button can be used to change the recorder’s
channels only.)
B Access Main Menu screen
Press MENU.
C Access Tuner Set screen
MAIN MENU
Press PUSH JOG rt to place the
PROGRAMME NAVIGATION
FUNCTION SET
pointer next to “TUNER SET”, then press
OK or PUSH JOG e.
TUNER SET
INITIAL SET
[R/T]
[MENU] : EXIT
D Select Auto CH Set mode
Press PUSH JOG rt to place the
pointer next to “AUTO CH SET”, then
press OK or PUSH JOG e.
TUNER SET
CH EDIT
AUTO CH SET
IMPORTANT
Although the provided remote control unit is compatible with JVC
satelite receiver and DVD, as well as many other models, it may
not work with your unit, or in some instances, may have limited
function capability.
[R/T]
[MENU] : EXIT
E Select TV system
TV SYSTEM SELECT
Press PUSH JOG rt to place the
pointer next to the appropriate TV
system, then press OK or PUSH JOG e.
● Auto Channel Set will start.
B/G
D/K
I
Cable Box or Satellite Receiver Multi-brand Code
CABLE BOX
BRAND NAME
CODE
CABLE BOX
BRAND NAME
CODE
[R/T]
[MENU] : EXIT
JVC
72, 73
KATHREIN
70, 71
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
CH FRQ SYS
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
AMSTRAD
BT
60, 61, 62, 63, 92 LUXOR
68
AUTO CH SET
PLEASE WAIT
72
81
MASPRO
NOKIA
PACE
PANASONIC
70
CANAL+
68, 87
CANAL SATELLITE 81
67, 86, 92
D-box
85
13, 14, 74
START
FINISH
– – – – – – –
[R/T]
[&] : DELETE
I
I
I
I
I
I
I
I
I
I
I
I
ECHOSTAR
FINLUX
51, 78, 79, 80, 82 PFT
69
[R/T]
: EDIT
[MENU] : EXIT
68
PHILIPS
PHONOTREND
SALORA
SKYMASTER
TPS
66, 84
GALAXIS
GRUNDIG
HIRSCHMANN
ITT
69, 88
64, 65
64
69
F Return to normal screen
Press MENU.
68
69
68
83
NOTE:
JERROLD
01, 04, 06, 11,12, VIDEOWAY
03, 09, 22, 76, 77
64
15, 28, 75
WISI
If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED -NO SIGNAL-” appears
on the screen in step 5. When this happens, make sure of the
aerial connection and press OK; Auto Channel Set will take place
again.
DVD Multi-brand Code
DVD BRAND NAME
CODE
JVC
55
58
56
57
IMPORTANT
PANASONIC
PHILIPS
TOSHIBA
● If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by Auto
Channel Set, the TV system setting for those channels may be
incorrect. Select the appropriate TV system for those
channels. ੬ “TV System Selection — When you see the
picture but the audio can’t be heard or sounds unnatural” on
page 19.
● Since your video recorder memorizes all detected stations
even if the reception condition is poor, some of those stored
stations may produce a noisy picture. To delete those stations,
੬ “Delete a Channel” on page 19.
— 18 —
Download from Www.Somanuals.com. All Manuals Search And Download.
B Access Channel list
Manual Channel Set
Press PUSH JOG rt to place the pointer next to “CH EDIT”,
Store channels that were not stored during “Auto Set Up” (੬ 5) or
then press OK or PUSH JOG e.
“Auto Channel Set” (੬ 18).
C Select position (e.g. 03)
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
[0-9] : INPUT CH
: FINE TUNING
[MENU] : EXIT
CH FRQ SYS
A Access Tuner Set screen
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press PUSH JOG rt until the section of
CH “03” begins blinking, then press OK
or PUSH JOG e.
Perform steps 1 – 3 of “Auto Channel Set” on page 18.
B Access Channel list
● Only “03” will blink.
Press PUSH JOG rt to place the pointer next to “CH EDIT”,
then press OK or PUSH JOG e.
D Select position (e.g. 09)
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
CH FRQ SYS
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
C Select position
Press number keys to input “0” and “9”.
● The two selected channels will be
swapped.
Press PUSH JOG rt to place the pointer next to an open
channel position, then press OK or PUSH JOG e.
D Select band
[Y] : CANCEL
● To cancel the channel swapping, press
PUSH JOG w.
: OK
Press PUSH JOG rt to place the pointer next to the band of your
[MENU] : EXIT
choice, then press OK to initiate Manual Channel Set.
E Store new positions
Press OK or PUSH JOG e.
● Repeat steps 3 – 5 as necessary.
BAND SELECT
MANUAL CH SET
PLEASE WAIT
VHF L
VHF H
F Return to normal screen
Press MENU.
UHF
VHF L 100MHZ
[R/T]
[MENU] : EXIT
[MENU] : EXIT
Fine-Tuning Channels
A Access Tuner Set screen
Perform steps 1 – 3 of “Auto Channel Set” on page 18.
E Set desired station
The screen to the right appears when a
station is detected.
STORE
CONTINUE
If you do not want to store the detected
station...
Press PUSH JOG rt to place the
pointer next to “CONTINUE”, then press
B Access Channel list
[R/T]
[MENU] : EXIT
Press PUSH JOG rt to place the pointer next to “CH EDIT”,
then press OK or PUSH JOG e.
OK or PUSH JOG e. Channel search will resume.
C Select channel to fine-tune
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
[R/T] : FINE TUNING
: SELECT SYSTEM
[MENU] : EXIT
CH FRQ SYS
If you want to store the detected station...
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press PUSH JOG rt to place the pointer next to “STORE”, then
press OK or PUSH JOG e. The Channel List appears again.
● The blueback screen and the TV picture currently being
broadcast appear alternately for 8 seconds each.
● If you want to store another channel, repeat steps 3 – 5.
● When channel search completes for that band, the Band Select
screen appears again. To set channels for other bands, select
another band and start Manual Channel Set again (੬ step 4
and 5).
Press PUSH JOG rt until the channel
you want to tune begins blinking, then
press OK twice.
● The “FRQ” number for that channel
starts blinking.
D Perform tuning
Press PUSH JOG rt until the picture becomes clearer, then press
OK or PUSH JOG e.
● Repeat steps 3 and 4 as necessary.
E Return to normal screen
Press MENU.
Delete a Channel
A Access Tuner Set screen
Perform steps 1 – 3 of “Auto Channel Set” on page 18.
TV System Selection — When you see the picture
B Access Channel list
but the audio can’t be heard or sounds unnatural
Press PUSH JOG rt to place the pointer next to “CH EDIT”,
then press OK or PUSH JOG e.
A Access Tuner Set screen
Perform steps 1 – 3 of “Auto Channel Set” on page 18.
C Select channel
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
CH FRQ SYS
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press PUSH JOG rt until the channel
B Access Channel list
you want to delete begins blinking.
Press PUSH JOG rt to place the pointer next to “CH EDIT”,
then press OK or PUSH JOG e.
[R/T]
[&] : DELETE
: EDIT
[R/T]
C Select channel
CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
CH FRQ SYS
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
[MENU] : EXIT
Press PUSH JOG rt until the channel
you want to change its TV system begins
blinking, then press OK three times.
● The “SYS” display for that channel
starts blinking.
D Delete channel
CH FRQ SYS
01 – – – – –
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
CH FRQ SYS
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press &.
● To re-store it, simply press
PUSH JOG w.
● Repeat steps 3 – 4 as necessary.
[R/T] : SELECT SYSTEM
: OK
[MENU] : EXIT
[R/T]
[Y] : ADD
D Select TV system
Press PUSH JOG rt to select the appropriate TV system
(BG ] DK ] I). Then press OK or PUSH JOG e.
● Repeat steps 3 and 4 as necessary.
[MENU] : EXIT
E Return to normal screen
Press MENU.
Swap Channel Positions
E Return to normal screen
Press MENU.
Example: To swap CH03 and CH09.
A Access Tuner Set screen
Perform steps 1 – 3 of “Auto Channel Set” on page 18.
— 19 —
Download from Www.Somanuals.com. All Manuals Search And Download.
You can use a camcorder as the source player and your video
recorder as the recorder.
Editing
A Make connections
aIf the camcorder has no S-VIDEO output connector...
... connect the camcorder's AUDIO/VIDEO OUT connectors to
the recorder's front panel AUDIO/VIDEO input connectors.
bIf the camcorder has an S-VIDEO output connector...
... connect the camcorder's S-VIDEO OUT and AUDIO OUT
connectors to the recorder's front panel S-VIDEO(S-2) and
AUDIO input connectors. The recorder's rear panel S-VIDEO IN
and AUDIO IN input connectors are also available.
Editing from a camcorder
● All necessary cables can be obtained from your dealer.
● You can also use another video recorder as the player instead of
a camcorder.
● When you select “EDIT” to dub tapes, be sure to select “AUTO”
(or “NORM” when the B.E.S.T. function is set to “OFF”) after
you finish dubbing the tapes.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your recorder.
● When a Master Edit Control-equipped JVC camcorder is used,
the camcorder is capable of controlling the recorder. Refer to
the camcorder's instruction manual for operating procedure.
IMPORTANT
● To edit, both the player and the recorder must be of the same
colour system. Select the appropriate colour system (੬ 16).
● PAL, SECAM and NTSC camcorders can be used as a player
for editing.
B Set recorder’s input mode
Press number key “0” and/or PR +/– to select “F-1” for the
AUDIO/VIDEO input connectors, or “S-2” for the AUDIO/S-
VIDEO input connectors, depending on the connectors being
used.
a If the camcorder has no S-VIDEO output connector...
Recorder
C Select “EDIT” for picture control set mode
Follow the “Picture Control” section on page 15, then select
“EDIT.”
D Start camcorder
Engage its Play mode.
VIDEO input
AUDIO
E Start recorder
Engage its Record mode.
input
Audio/Video Cable
(not provided)
Edit to or from Another Video Recorder
Player
Your recorder
TV Receiver
VIDEO OUT
Player
(MONO)
Camcorder
AUDIO OUT
VIDEO CHANNEL
RF Cable (provided)
AV Cable
(not provided)
b If the camcorder has an S-VIDEO output connector...
Recorder
Another recorder
Recorder
Recorder
Your recorder
TV Receiver
S-VIDEO (S-2)
input
AUDIO
input
(MONO)
Audio Cable (not provided)
S-Video Cable (provided)
VIDEO
CHANNEL
AV Cable
(not provided)
RF Cable
(provided)
S-VIDEO OUT
Player
Another recorder
Camcorder
AUDIO OUT
Player
— 20 —
Download from Www.Somanuals.com. All Manuals Search And Download.
You can use your video recorder as the source player or the
recording deck.
System Connections
A Make connections
Connect the player's AUDIO/VIDEO OUT connector to the
recorder's AUDIO/VIDEO IN connector.
Connecting/Using a Stereo System
These instructions enable you to connect your video recorder to
your Hi-Fi stereo system (if you have one) and listen to the
soundtrack through the stereo.
● Use the L connector for monaural connection.
B Set recording deck’s input mode
Set to AUX. With this video recorder, press number key “0” and/or
PR +/– to select depending on the connector being used — "L-1"
for the rear panel VIDEO/AUDIO input connectors, or “F-1” for
the front panel VIDEO/AUDIO input connectors.
FM Tuner
CD Player
C Select “EDIT” for picture control set mode
Follow the “Picture Control” section on page 15, then select
“EDIT.”
Stereo Amplifier
I
AUX IN or TAPE MONITOR
D Start source player
Engage its Play mode.
Audio Cable
(not provided)
E Set recording deck
Engage its Record mode.
NOTES:
Speaker Television
Speaker
● To edit, both the player and the recorder must be of the same
colour system. Select the appropriate colour system (੬ 16).
● When you use this recorder as the player for editing, be sure to
set “O.S.D.” to “OFF” before starting (੬ 16).
● All necessary cables can be obtained from your dealer.
● NTSC tapes being played back in the "NTSC]PAL" mode
(੬ 16) cannot be dubbed to another recorder.
● When you dub an NTSC tape using your recorder as the
playback deck, select "NTSC 3.58" (or "NTSC 4.43") for "NTSC"
setting (੬ 16).
● When you select “EDIT” to dub tapes, be sure to select “AUTO”
(or “NORM” when the B.E.S.T. function is set to “OFF”) after
you finish dubbing the tapes (੬ 15).
● If you are using another recorder with S-Video and Audio input/
output connectors, you can connect those connectors to this
recorder's S-VIDEO IN/S VIDEO OUT and AUDIO IN/OUT
connectors.
When Using Your Video Recorder As The Source Player ...
... connect its rear panel S VIDEO OUT and AUDIO OUT
connectors to the recording deck's S-Video and Audio input
connectors.
(MONO)
Mains
outlet
Rear View
AUDIO OUT
Make Connections
Connect the AUDIO OUT L and R connectors on your video
recorder to the AUX IN or TAPE MONITOR terminals on your
stereo system's receiver or amplifier.
NOTES:
● When connecting your recorder's audio output connectors to a
stereo amplifier, make sure you connect L and R correctly.
● If stereo or bilingual TV broadcasts are receivable in your area,
this recorder can record them independently of the TV set and
play them back through the connected stereo system.
● When listening to sound through the connected stereo system,
turn the TV's volume down completely.
When Using Your Video Recorder As The Recording Deck ...
... connect its front panel S-VIDEO and AUDIO input
connectors to the source player's S-Video and Audio output
connectors. Then, set the recorder's input mode to “S-1”.
CAUTIONS
● This recorder has a dynamic range of more than 80 dB with
regards to its Hi-Fi audio capability. It is recommended that you
check the maximum level if you are going to listen to the Hi-Fi
audio signals through a stereo amplifier. A sudden surge in the
input level to the speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do
not place the speakers adjacent to the TV set as this can
adversely affect the video playback picture.
— 21 —
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNER/TIMER
TV channel storage
capacity
Specifications
: 99 positions (+AUX position)
: Frequency synthesized tuner
Tuning system
Channel coverage
VHF
GENERAL
Power requirement
Rating
Operating
Power consumption
Power on
Power off
Temperature
Operating
: (Low) 42 MHz – 175 MHz/
(High) 175 MHz – 470 MHz
: 470 MHz – 870 MHz
: UHF channels (Adjustable E28 – E60)
: AC 110 V – 240 Vd, 50 Hz/60 Hz
: AC 90 V – 260 Vd, 50 Hz/60 Hz
UHF
Aerial output
Memory backup time
: 18 W
: 3.5 W
: Approx. 6 months
Estimated figure based on supplied
fresh battery; actual performance may
differ.
: 5°C to 40°C
Storage
Operating position
: –20°C to 60°C
: Horizontal only
ACCESSORIES
Provided accessories
Dimensions (W x H x D) : 400 mm x 94 mm x 265 mm
: RF cable,
Weight
: 3.0 kg
S-Video cable,
Format
Maximum recording time
(SP)
: S-VHS/VHS standard
Infrared remote control unit,
“R6/UM-3” battery x 2,
Lithium battery – CR2025 –
: 240 min. with E-240 video cassette
(PAL/MESECAM)
Specifications shown are for SP mode unless otherwise specified.
Design and specifications subject to change without notice.
: 160 min. with T-160 video cassette
(NTSC)
(LP)
(EP)
: 480 min. with E-240 video cassette
(PAL/MESECAM)
: 720 min. with E-240 video cassette
(PAL/MESECAM)
: 480 min. with T-160 video cassette
(NTSC)
VIDEO/AUDIO
Signal system
: PAL-type colour signal and CCIR
monochrome signal, 625 lines/
50 fields
: NTSC colour and EIA monochrome
signals, 525 lines/60 fields
Recording system
: DA-4 (Double Azimuth) head helical
scan system
Signal-to-noise ratio
Horizontal resolution
S-VHS
: 45 dB
: 400 lines
VHS PAL/MESECAM : 250 lines
VHS NTSC
Frequency range
Normal audio
Hi-Fi audio
: 220 lines
: 70 Hz to 10,000 Hz
: 20 Hz to 20,000 Hz
Input/Output
: RCA connectors:
IN x 2, OUT x 1
S-Video connectors:
IN x 2, OUT x 1
— 22 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Multi-System Compatibility
Off-Air Recording
The built-in multi-system tuner is capable of receiving PAL B/G, I and D/K, and SECAM B/G and D/K and NTSC broadcasts.
TV system
HR-S6960AA
Recorded Tape
PAL
Recording circuit
PAL
PAL B/G, I, D/K
MESECAM
NTSC
Multi-system tuner
(B/G, I, D/K)
SECAM B/G,
D/K (OIRT)
MESECAM
NTSC 3.58
NTSC (M)
NOTE:
This model does not operate in BRAZIL (PAL-M) or ARGENTINA (PAL-N).
Playback
The recorder can play back all 3 types of recorded tape.
Recorded Tape
HR-S6960AA
TV system
PAL
Playback circuit
Multi-system receiver
PAL
MESECAM
NTSC
PAL
(B/G, D/K, I, H)
NTSC (M)
Built-in
RF converter
K, I, G, H
MESECAM
RF OUT
NTSC PAL
NTSC 3.58 MHz
Multi-system monitor
Manual switching
Manual switching
PAL
SECAM
NTSC 3.58
NTSC 4.43
NTSC 4.43 MHz
VIDEO OUT
AUDIO OUT
NOTE:
When viewing NTSC tapes on a PAL TV set:
● The picture may shrink vertically with black bars appearing at the top and bottom of the screen. This is not a malfunction on the part of
the video recorder nor the TV.
● The picture may roll up or down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the
TV does not have a V-HOLD control.)
● During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.
ATTENTION
When this recorder is connected to a multi-system TV, the audio signal may not be heard or may be noisy if the colour system select
switch of the TV is adjusted to the AUTO position. In such a case, set the TV's colour system select switch to the appropriate position
which corresponds to the TV system you have selected at the TV System Select screen.
— 23 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Tape-To-Tape Editing
There are 4 different types of recorded tape, depending on the signal recorded.
Dubbed Tape
Recorded Tape
Playback equipment
HR-S6960AA
PAL
PAL
PAL
MESECAM
SECAM
PAL
MESECAM
MESECAM
SECAM
MESECAM
Recording circuit
NTSC 3.58 MHz
NTSC 4.43 MHz
NTSC 3.58 MHz
NTSC 4.43 MHz
NTSC
NTSC
— 24 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily
corrected, and this can save you the trouble of sending your video recorder off for repair.
Power
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
No power is applied to the ● The mains power cord is disconnected.
recorder.
● Connect the mains power cord.
The clock is functioning
properly, but the recorder
cannot be powered.
● “#” is displayed on the display panel with Auto
Timer set to “OFF”.
● Press the # button to turn the “#” indicator off.
The remote control won't ● The batteries are discharged.
● Replace the dead batteries with new ones.
● Press # on the remote control.
● Reset A/B code. (੬ 17)
function.
● Timer is on.
● Remote control A/B code is wrong.
Tape Transport
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The tape will not rewind or ● The tape is already fully rewound or fast-
● Check the cassette.
fast-forward.
forwarded.
Playback
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The playback picture does ● If you're using the RF OUT connection . . .
● If you are using the RF OUT connection . . .
. . . set the TV receiver to the VIDEO channel.
(੬ 5)
not appear while the tape
is running.
. . . the TV receiver's channel selector is not set to
the VIDEO channel.
. . . the recorder's VIDEO channel has not been
correctly set.
● If you're using the AV or S-VIDEO connection, the
TV receiver is not set to the AV mode.
. . . Perform “Video Channel Set”. (੬ 5)
If you are using the AV or S-VIDEO connection, set
the TV to its AV mode.
Noise appears during
visual search.
● This is normal.
Noise appears during
normal playback.
● The automatic tracking mode is engaged.
● The automatic tracking mode is engaged.
● Try manual tracking. (੬ 7)
Noise appears during
slow-motion playback.
● Try manual tracking. (੬ 7)
Noise appears during still
playback.
● Press PR +/– few times to remove the noise bars
from the screen.
Breaks are noticeable in
Hi-Fi soundtrack.
● Automatic tracking is engaged.
● Engage and adjust tracking manually. (੬ 7)
The playback picture is
blurred or interrupted
while TV broadcasts are
clear. Or “USE CLEANING
CASSETTE” appears on the
screen.
● The video heads may be dirty.
● The heads must be cleaned. Use a dry cleaning
cassette –TCL-2– or consult your JVC dealer.
Playback picture has a loss ● The wrong colour system is selected for the tape ● Select the correct colour system. (੬ 16)
of colour.
being played back.
● The wrong colour system was selected during
recording.
● Once recorded, the signal cannot be corrected. Be
sure to choose the correct setting before recording.
No sound accompanies
the playback picture.
● The TV system you have selected at the TV System ● Set it to the correct position for the TV broadcast
Select screen is incorrect. system used in your area. (੬ 17)
— 25 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Recording cannot be
started.
● There is no cassette loaded, or the cassette loaded ● Insert a cassette, or using adhesive tape, reseal the
has had its Record Safety tab removed. slot where the tab was removed.
TV broadcasts cannot be
recorded.
● "L-1", "F-1", "S-1" or "S-2" has been selected as the ● Set to the desired channel.
input mode.
Tape-to-tape editing is not ● The source (another video recorder, camcorder)
● Confirm that the source is properly connected.
possible.
has not been properly connected.
● All necessary power switches have not been
turned on.
● Confirm that all units' power switches are turned
on.
● The input mode is not correct.
● Set the input mode to “L-1”, “F-1”, “S-1” or “S-2”.
Camcorder recording is
not possible.
● The camcorder has not been properly connected. ● Confirm that the camcorder is properly connected.
● The input mode is not correct.
● Set the input mode to “L-1”, “F-1”, “S-1” or “S-2”.
Timer Recording
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Timer recording won't
work.
● The clock and/or the timer have been set
incorrectly.
● Re-perform the clock and/or timer settings.
● The timer is not engaged.
● Press # and confirm that “#” is displayed on the
display panel.
On-screen timer
programming is not
possible.
● Timer recording is in progress.
● Timer programming can't be performed while a
timer recording is in progress. Wait until it finishes.
“#” on the display panel
won't stop blinking.
● The timer is engaged but there's no cassette
loaded.
● Load a cassette with the Record Safety tab intact,
or cover the hole using adhesive tape.
● The loaded cassette has had its Record Safety tab ● Remove the cassette and cover the hole with
removed.
adhesive tape, or insert a cassette with the Record
Safety tab intact.
“#” blinks for 10 seconds ● # has been pressed when there are no programs ● Check the programmed data and re-program as
and the Timer mode is
disengaged.
in memory, or the timer record information has
been programmed incorrectly.
necessary, then press # again.
The power shuts off and
“#” won't stop blinking.
● The end of the tape was reached during timer
recording.
● The programme may not have been recorded in its
entirety. Next time make sure you have enough
time on the tape to record the entire programme.
The G-CODE/SHOWVIEW
system does not timer-
record properly.
● The recorder's channel positions have been set
incorrectly.
● Refer to “G-CODETM/SHOWVIEWTM System Setup”
and re-perform the procedure. (੬ 10)
Other Problems
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Whistling or howling is
heard from the TV during
camcorder recording.
● The camcorder's microphone is too close to the
● Position the camcorder so its microphone is away
from the TV.
● Turn the TV's volume down.
TV.
● The TV's volume is too high.
When scanning channels, ● Those channels have been designated to be
some of them are skipped
over.
● If you need the skipped channels, restore them.
(੬ 5)
skipped.
The channel cannot be
changed.
● Recording is in progress.
● Press 9 to pause the recording, change channels,
then press 4 to resume recording.
Channel settings that were ● After the manual settings were made, Auto
● Perform manual setting again.
made manually seem to
have changed or
disappeared.
Channel Set was performed.
No channels are stored in ● The TV aerial cable was not connected to the
● Connect the TV aerial cable to the recorder
properly and turn off the recorder power once,
then turn the recorder power back on again. The
recorder will try Auto Set Up again. (੬ 5)
the recorder's memory.
recorder when Auto Set Up was performed.
“– –:– –” is displayed on
the front display panel after
a power outage.
● The lithium battery is exhausted.
● Replace the lithium battery with a new one.
(੬ 2).
— 26 —
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
— 27 —
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
Printed in China
0703-AH-PJ-BJ
® Registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD.
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
Download from Www.Somanuals.com. All Manuals Search And Download.
|