JVC Tablet Accessory MP XP7220KR User Manual

MP-XP7220KR,MP-XP5220KR  
SERVICE MANUAL  
Mobile mini note PC  
G2002100304  
MP-XP7220KR,MP-XP5220KR  
Area Suffix  
KR ------------------  
Korea  
TABLE OF CONTENTS  
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2  
1
1.1  
1.2  
1.3  
1.4  
1.5  
1.6  
Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2  
Preinstallation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7  
Caution in exchanging a bottom case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8  
Replace procedure of main board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8  
Operation check item list after the repair is completed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9  
Another sales option list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9  
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.  
No.G1004  
2003/02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP-XP7220KR,MP-XP5220KR  
1.1.3 Removing the top case and LCD panel assembly (See  
Figure 1 and Figure 5 ~ Figure 8)  
• Prior to performing the following procedure, remove the key-  
board assembly.  
(1) Insert a single-slotted screwdriver or a flat screwdriver in a  
space b on the underside of the hinge cover. Then, remove  
the hinge cover by pulling the screwdriver in the direction  
indicated by the arrow.  
Hinge cover  
And then, remove one more hinge cover at the other side  
of the main body.  
(2) Remove the four screws B attaching the top case.  
(3) Remove one screw C (short) and one screw D (long) at-  
taching the shield plate.  
(4) Reverse the main body, and remove the four screws E on  
the bottom of the main body. (See Figure 1)  
(5) Disconnect the connector wire from the connector CN2 on  
the mother board. Similarly, remove the connector wires  
from the connectors CN3, CN5, and CN7.  
(6) Remove one latch c on the rear side of the main body, and  
release the two joints d while moving the top case in the  
rear direction.  
Space b  
Fig.6  
CN2  
B
C
Shield plate  
CN3  
D
B
B
Latch c  
Fig.7  
Top case  
CN7  
B
CN5  
Top case  
Fig.5  
Bottom case  
Joint d  
Fig.8  
(No.G1004)1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MP-XP7220KR,MP-XP5220KR  
1.1.4 Removing the mother board  
Microphone and  
headphone jack  
(See Figure 9 ~ Figure 11)  
• Prior to performing the following procedure, remove the key-  
board assembly, the top case, and the LCD panel assembly.  
(1) Remove one screw F (short), one screw G (middle), and  
the two screws H (long) attaching the mother board.  
Mother board  
(*In attaching the mother board, tighten H , H , G, and F  
in this order.)  
(2) Lift the mother board while pushing the microphone and  
headphone jack in the direction indicated by the arrow, and  
remove the mother board.  
1
2
Battery detector  
switch  
2
*Be careful not to damage the battery detector switch on  
the backside of the mother board.  
* In attaching the mother board, put the lever of the PCMCIA slot  
through the bottom case, and then push and attach the micro-  
phone and headphone jack.  
Bottom case  
F
Mother board  
H1  
1
Fig.11  
Caution  
In attaching the mother board to the bottom case or in attach-  
ing the top case to the bottom case, soft workbench must not  
be used because it may distort the bottom case and the top  
case. Attachment operation must be performed on workbench  
hard enough.  
H2  
G
Fig.9  
2
1
1
Microphone and  
headphone jack  
Mother board  
Fig.10  
1-4 (No.G1004)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MP-XP7220KR,MP-XP5220KR  
1.1.5 Removing the parts on the mother board  
(See Figure 12 ~ 15)  
• Prior to performing the following procedure, remove the moth-  
er board.  
*Removing the fan assembly  
(1) Remove the four screws I attaching the fan assembly.  
(2) Disconnect the connector wire from the connector CN13 on  
the mother board.  
*Removing the hard disc drive  
(1) Remove one screw J at the side of the mother board where  
the hard disc drive is not attached.  
(2) Remove the hard disc drive by moving the hard disc drive  
in the direction indicated by the arrow.  
*Removing the PCMCIA slot  
(1) Remove one screw K (long) and the two screws L (short)  
at the side of the mother board where the PCMCIA slot is  
not attached.  
(2) Hold and lift the connector side of the PCMCIA slot, and re-  
move the PCMCIA slot.  
PCMCIA slot  
Fig.14  
*Removing the modem pack  
(1) Remove one screw M attaching the modem pack.  
(2) Pull out the socket wire connected to the modem pack.  
(3) Lift the modem pack, and remove it.  
Fan assembly  
I
CN13  
Modem pack  
Socket  
Fig.15  
Hard disc drive  
PCMCIA slot  
Fig.12  
J
L
M
K
Socket wire  
Modem pack  
Fig.13  
(No.G1004)1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MP-XP7220KR,MP-XP5220KR  
1.1.6 Removing the top case and the LCD panel assembly  
(See Figure 16)  
Rubber pad and screw O  
Latch  
• Prior to the following procedure, remove the top case and the  
LCD panel assembly from the bottom case.  
(1) Remove the two screws N attaching the hinge.  
(2) Remove the tapes fixing the two wires of the LCD panel as-  
sembly if necessary.  
N
Hinge  
N
Hinge  
Tape  
Tape  
LCD  
Latch  
Latch  
Latch  
Fig.16  
1.1.7 Removing the LCD panel  
(See Figure 17 and Figure 18)  
Fig.17  
• Prior to the following procedure, remove the LCD panel as-  
sembly.  
(1) Remove the two rubber pads (fixed to the panel with adhe-  
sive tapes) by using a sharp tool.  
(2) Remove the two screws O attaching the LCD panel frame.  
(3) Lift and the centers of the four sides of the LCD panel from  
inside to an outward direction. (It is soft enough to be lifted.)  
Then, latches in the centers of the four sides and also other  
latches are removed. To remove all the latches, lift the four  
sides from inside to an outward direction.  
LCD  
P
P
* Be careful not to damage the LCD or apply any stress to  
the LCD.  
(4) Remove the two screws P attaching the LCD.  
(5) Remove one screw Q attaching the inverter board, and dis-  
connect the socket wire from the connector CN2 on the in-  
verter board.  
QQ  
CN2  
Inverter board  
Fig.18  
1-6 (No.G1004)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
MP-XP7220KR,MP-XP5220KR  
1.2 Preinstallation procedure  
No data including Windows XP has been recorded in service parts HDD.  
It is necessary to put data in HDD after HDD is replaced.  
< The following materials are needed >  
*CD-ROM drive (model name MP-CDX1E)  
*CD for installing HD Image (a set of five CDs)  
<Procedure>  
(1) Connect CD-ROM drive (model name MP-CDX1E) and the Mobile Mini Note PC by using PC card slot.  
(2) Insert the 1st CD for installing HD Image in CD-ROM drive.  
(3) Push a power supply button.  
The 1st CD starts its operation, and then installation starts.  
After a while, the 1st CD finishes its operation.Then, the following message is displayed.  
Image center  
( ? ) Insert media 2 containing  
"xxxxx" into drive Q  
OK  
Cancel  
(4) Take out the 1st CD inside the CD-ROM drive.  
(5) Insert the 2nd CD in CD-ROM drive.  
(6) Click "OK" button.  
After a while, the 2nd CD finishes its operation.  
Then, the message "Please insert the next CD." is displayed in the same way as in the 1st CD.  
(7) In the same way as in the 1st and the 2nd CD, insert each 3rd, 4th, and 5th CD in this order and install them.  
(8) When the 5th CD finishes to be installed, push a power supply button and turn the power off.  
* When the following error message is displayed, perform the procedure again from Procedure 1 started above.  
Image center  
( ? ) The media does not content correct file.  
OK  
(No.G1004)1-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
MP-XP7220KR,MP-XP5220KR  
1.3 Caution in exchanging a bottom case  
1.3.1 As for COA LABEL  
Neither "LE40888-001A/COA LABEL PRO" nor "LE40888-002A/COA LABEL HOME" can be reused.  
COA LABEL is also necessary in exchanging a bottom case.  
1.3.2 As for serial label  
"Serial label" where model name and serial number are written is not dealt with as service parts.  
Please reuse it.  
Please remove a label with exfoliation agent:  
Parts number -- UN-001  
Parts name ----- SUBSIDIALY MATERIAL  
*How to remove a label  
(1) Drip a few drops of exfoliation agent on an attached spatula.  
(2) Immediately after (1), turn over the label from its edge with the spatula while dripping the exfoliation agent on a label by using  
the spatula.  
(3) If adhesive agent still remains in the surface of the bottom case, please drip a few drops of exfoliation agent on the agent and  
wipe it with clean tissue paper.  
1.4 Replace procedure of main board  
1.4.1 Parts are put and substituted from former main board to a new main board.  
* The [15-100324200 / AWARD BIOS LABEL] is pasted and substituted.  
* The [13-N6K10P220 / SD DUMMY CARD] is replaced.  
* The [07-016402032 / BATT-LI] is put and substituted.  
* The [04-132051170 / MODEM 56K] is put and substituted.  
* The [14-140522020 / WIRE CABLE FOR MDC] is put and substituted.  
* The [HDD] is put and substituted.  
* The [13-N6K10M122 / FAN HEAT SINC BLOCK] is put and substituted.  
* The [04-001212250 / SDRAM] is put and substituted. (Only when SDRAM is installed)  
* The [13-N6K10C020 / GASKET] is pasted and changes.  
* The [13-N6K10L252 / COAXIAL MYLAR] is pasted and changes.  
* The [13-N6K10L160 / THERMAL PAD RAM] is pasted and changes.  
1.4.2 Adjust it after exchanging the substrate.  
* Make the version of BIOS equal to former main board.  
The version of BIOS of a new main board is 0200.  
Follow it when the up-grade of BIOS is hoped to the customer.  
* Set the clock of BIOS.  
Because the coin type battery has not placed to the main board, the clock is not accurate.  
1.4.3 Do the operation check after exchanging the substrate.  
Execute the operation check following "Operation check item list after the repair is completed".  
1-8 (No.G1004)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MP-XP7220KR,MP-XP5220KR  
1.5 Operation check item list after the repair is completed  
Item  
Contents  
Required equipment  
1
IEEE1394  
Is connected with IEEE1394 port the Digital video camera and Digital video camera made of our company.  
do recognize it?  
2
3
SD CARD  
PC CARD  
Is connected with SD card slot the SD card and do recognize it? SD card on the market.  
Check whether PC card operates properly when it is connected PC card corresponding to Card Bus on the  
to PC card slot for Card Bus.  
Check whether PC card operates properly when option CD- (Example:100Mbase-T LAN card)  
ROM drive is inserted in PC card slot. CD-ROM drive of option.  
market.  
4
USB  
MIC  
Is connected with USB the Digital video camera and do recog- Digital video camera made of our company.  
nize it?  
USB mouse on the market.(Transfer rate:Low)  
Is connected with USB the mouse and do recognize it?  
5
6
Is connected with the MIC terminal a MIC on the market, and is MIC on the market.  
recognized it?  
HEADPHONE Is connected with the headphone terminal a headphone on the Headphone on the market.  
market, and is recognized it?  
7
8
LAN  
Do connect with the network, and do recognize it?  
Can the telephone line be connected, and it connect it with the Telephone line.PPP account to connect dial-  
Internet? up with the Internet.  
Does it connect with the monitor, and is the image displayed? Monitor for PC  
VGA Cable (Provision)  
Network  
MODEM  
9
VGA  
10 DC in  
Can AC be driven?  
General power supply  
Outer battery  
11 BATTERY  
Is the outer battery recognized?  
12 LID SWITCH Does the LID switch work?  
13 RESET Is RESET effective?  
14 KEYBOARD Is the key input effective?  
15 STICK  
Is the STICK effective?  
16 SPEAKER  
17 RUNNING  
Is the sound emitted from both channels of the speaker?  
Is not there trouble after it playback by using Windows media  
player for continuousness eight hours?  
1.6 Another sales option list  
Product category  
Model name  
MP-BCX1E  
BN-LS12E  
BN-LL21E  
MP-CDX1E  
MP-VGX1E  
MP-BGX2E  
Note  
BATTERY CHARGER  
Lithium-Ion BATTERY  
Lithium-Ion BATTERY  
CD-ROM DRIVE  
Same as attached goods of the main body.  
EXTERNAL DISPLAY CABLE  
CARRYING BAG  
(No.G1004)1-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MP-XP7220KR,MP-XP5220KR  
VICTOR COMPANY OF JAPAN, LIMITED  
AV & MULTIMEDIA COMPANY MOBILE IT CATEGORY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan  
(No.G1004)  
Printed in Japan  
200302WPC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ingersoll Rand Sander 8448A1 User Manual
Initio Network Card INI 9090U User Manual
Jenn Air Cooktop CCE3401 User Manual
JVC DVD Recorder CU VD20U User Manual
JVC Furnace GR DVL9000 User Manual
Kambrook Food Processor KFP95 User Manual
Kenmore Dishwasher 6651312 User Manual
KitchenAid Dishwasher KD 27A User Manual
KitchenAid Microwave Oven KCMS2055 User Manual
Klipsch Speaker Cornwall III User Manual