MICRO COMPONENT SYSTEM
MIKRO-KOMPONENTEN-SYSTEM
SYSTEME DE MICROCOMPOSANTS
MIKRO KOMPONENTENSYSTEEM
SYSTEMAS DE MICROCOMPONENTES
SISTEMA A MICROCOMPONENTI
UX-V20R/UX-V10
COMPACT
COMPACT
DIGITAL AUDIO
DIGITAL AUDIO
VERTICAL DISC
LOADING MECHANISM
VERTICAL DISC
LOADING MECHANISM
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
MICRO COMPONENT SYSTEM UX-V20R
FM
AUTO
MICRO COMPONENT SYSTEM UX-V10
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
CD
FM/AM
CD
FM/AM
STANDBY
CD
AHB
PRO
STANDBY
CD
AUX
REC
AHB
PRO
AUX
REC
DISPLAY
MODE
VOLUME
REPEAT
PROGRAM
PTY/EON
UP
VOLUME
REPEAT
PROGRAM
UP
TIMER
SET
TIMER
SET
RANDOM
DOWN
TREBLE
REV
MODE
.
CLOCK
RANDOM
DOWN
TREBLE
REV.
MODE
CLOCK
AHB
PRO
BASS
CANCEL
AHB
PRO
BASS
CANCEL
CD
VOLUME
OPEN/CLOSE
CD
VOLUME
OPEN/CLOSE
TAPE
FM/AM
CD
TAPE
FM/AM
CD
PHONES
REMOTE CONTROL RM-SUXV20R
PHONES
REMOTE CONTROL RM-SUXV10E
DOWN
MULTI CONTROL
UP
DOWN
MULTI CONTROL
UP
UX-V20R
UX-V10
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
MANUEL DE INSTRUCCIONES
ISTRUZIONI
Model No.
Serial No.
GVT0031-006A
[E]
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate
the apparatus as follows:
Voorzichtig: Goede ventilatie vereist
Om brand, elektrische schokken en beschadiging te voorkomen, moet
u het toestel als volgt opstellen:
1 Front:
1 Voorkant:
No obstructions and open spacing.
2 Sides/ Top/ Back:
Geen belemmeringen en voldoende ruimte.
2 Zijkanten/boven-/onderkant:
No obstructions should be placed in the areas shown by the
dimensions below.
Geen belemmeringen plaatsen in de hieronder aangegeven zones.
3 Onderkant:
3 Bottom:
Op vlakke ondergrond plaatsen. Voldoende ventilatieruimte voorzien
door het toestel op een onderstel met een hoogte van 10 cm of
meer te plaatsen.
Place on the level surface. Maintain an adequate air path for
ventilation by placing on a stand with a height of 10 cm or more.
Vorsicht: Ausreichende Belüftung
ZurVermeidungvonelektrischenSchlägen,FeuerundsonstigenSchäden
sollte das Gerät unter folgenden Bedingungen aufgestellt werden:
1 Vorderseite:
Precaucion: ventilación correcta
Para evitar el riesgo de descargas eléctricas e incendio y prevenir
posibles daños, instale el equipo en un lugar que cumpla los siguientes
requisitos:
Hindernisfrei und gut zugänglich.
1 Parte frontal:
2 Seiten- und Rückwände:
Sin obstrucciones, espacio abierto.
Hindernisfrei in allen gegebenen Abständen (s. Abbildung).
3 Unterseite:
2 Lados/parte superior/parte posterior:
No debe haber ninguna obstrucción en las áreas mostradas por las
dimensiones de la siguiente figura.
3 Parte inferior:
Die Stellfläche muß absolut eben sein. Sorgen Sie für ausreichende
Luftzufuhr durch Aufstellung auf einem Stand mit mindestens 10 cm
Höhe.
Sitúe el equipo sobre una superficie nivelada. Mantenga un espacio
adecuado para permitir el paso del aire y una correcta ventilación,
situando el equipo sobre un soporte de 10 o más cm de allura.
Attention: Aération correcte
Attenzione: Per una corretta ventilazione
Per prevenire il rischio di scosse elettriche e di incendio ed evitare
possibili danni, collocare le apparecchiature nel modo seguente:
1 Parte anteriore:
Pour prévenir tout risque de décharge électrique ou d’incendie et éviter
toute détérioration, installez l’appareil de la manière suivante:
1 Avant:
Bien dégagé de tout objet.
Nessun ostacolo e spazio libero.
2 Côtés/dessus/dessous:
2 Lati/Parte superiore/Retro:
Assurez-vous que rien ne bloque les espaces indiqués sur le
schéma ci-dessous.
Lasciare libere le zone indicate dalle dimensioni di seguito.
3 Base:
3 Dessous:
Collocare su una superficie piana. Consentire un’adeguata
ventilazionedell’impiantoappoggiandolosuuntavolinettoaltoalmeno
10 cm.
Posez l’appareil sur une surface plane et horizontale. Veillez à ce
que sa ventilation correcte puisse se faire en le plaçant sur un sup-
port d’au moins dix centimètres de hauteur.
Front view
Vorderansicht
Face
Side view
Seitenansicht
Côté
Vooraanzicht
Zijaanzicht
Vista frontal
Vista frontale
Vista lateral
Vista laterale
15 cm
15 cm
COMPACT
DIGITAL AUDIO
15 cm
VERTICAL DISC
LOADING MECHANISM
UX-V20R
MICRO COMPONENT SYSTEM UX-V20R
UX-V10
1 cm
1 cm
15 cm
10 cm
15 cm
TAPE
FM/AM
CD
UX-V20R/UX-V10
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT FOR LASER PRODUCTS / WICHTIGER HINWEIS FÜR LASER-PRODUKTE / IMPORTANT POUR LES PRODUITS LASER /
BELANGRIJKE INFORMATIE VOOR LASERPRODUKTEN / IMPORTANTE PARA LOS PRODUCTOS LÁSER / IMPORTANTE PER I
PRODOTTI LASER
REPRODUCTION OF LABELS/ANBRINGUNGSORTE FÜR LASER-PRODUKTE/REPRODUCTION DES ETIQUETTES/VERKLARING VAN
DE LABELS/REPRODUCCIÓN DE ETIQUETAS/RIPRODUZIONE DELLE ETICHETTE
1
1
1
CLASSIFICATION LABEL, PLACED ON REAR ENCLOSURE
KLASSIFIKATIONSETIKETTE AN DER RÜCKSEITE
2
2
2
WARNING LABEL, PLACED INSIDE THE UNIT
WARNETIKETTE IM GERÄTEINNEREN
ETIQUETTE DE CLASSIFICATION, PLACÉE A L'ARRIÈRE DU
COFFRET
ETIQUETTE D'AVERTISSEMENT PLACÉE À L'INTERIEUR DE
L'APPAREIL
1
1
1
KLASSIFIKATIELABEL, OP DE ACHTERZIJDE VAN HET
APPARAAT
2
2
2
WAARSCHUWINGSLABEL, IN HET APPARAAT
ETIQUETA DE CLASIFICACIÓN, PEGADA EN LA PARTE
POSTERIOR DE LA CAJA
ETIQUETA DE ADVERTENCIA, PEGADA EN EL INTERIOR DE
LA UNIDAD
ETICHETTA DI CLASSIFICAZIONE, SITUATA SUL
RIVESTIMENTO POSTERIORE
ETICHETTA DI AVVERTENZA, SITUATA ALL'INTERNO
DELL'APPARECCHIO
DANGER: Invisible laser VARNING: Osynlig laser-
radiation when open and strålning när denna del är
interlock failed or defeated. öppnad och spärren är
AVOID DIRECT EXPOSURE urkopplad. Betrakta ej
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsæt-
VARO: Avattaessa ja suo-
jalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
CLASS
LASER
1
(e)
(s)
(d)
(f)
TO BEAM.
strålen.
telse for stråling
säteeseen.
PRODUCT
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock failed
or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user service-
able parts inside the Unit; leave all servicing to qualified service
personnel.
1. KLAS 1 LASERPRODUKT
2. GEVAARLIJK: Onzichtbare laserstraling wanneer open en de
beveiliging faalt of uitgeschakeld is. Voorkom het direkt
blootstaan aan de straal.
3. VOORZICHTIG: De bovenkap niet openen. Binnenin het toestel
bevinden zich geen door de gebruiker te repareren onderdelen:
laat onderhoud over aan bekwaam vakpersoneel.
1. LASER-PRODUKT DER KLASSE 1
1. PRODUCTO LASER CLASE 1
2. PELIGRO: En el interior hay radiación láser invisible. Evite el
contacto directo con el haz.
3. PRECAUCIÓN: No abra la tapa superior. En el interior de la
unidad no existen piezas reparables por el usuario; deje todo
servicio técnico en manos de personal calificado.
2. GEFAHR: Unsichtbare Laserstrahlung bei Öffnung und
fehlerhafter oder beschädigter Spre. Direkten Kontakt mit dem
Strahl vermeiden!
3. ACHTUNG: Das Gehäuse nicht öffnen. Das Gerät enthält
keinerlei Teile, die vom Benutzer gewartet werden können.
Überlassen Sie Wartungsarbeiten bitte qualifizierten
Kundendienst-Fachleuten.
1. PRODUIT LASER CLASSE 1
1. PRODOTTO LASER CLASSE 1
2. ATTENTION: Radiation laser invisible quand l'appareil est ouvert
ou que le verrouillage est en panne ou désactivé. Eviter une
exposition directe au rayon.
2. PERICOLO: Radiazione laser invisibile quando l'apparecchio è aperto
ed il dispositivo di sicurezza è guasto o disattivato. Evitare
l'esposizione diretta ai raggi.
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n'y a
aucune pièce utilisable à l'intérieur. Laisser à un personnel
qualifié le soin de réparer votre appareil.
3. ATTENZIONE: Non aprire il coperchio superiore. Non vi sono parti
adoperabili dall'utente all'interno di questo apparecchio; lasciare tutti i
controlli a personale qualificato.
G-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for purchasing the JVC Micro Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have any query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
■ The controls and operations have been designed to make them very easy to use, freeing you to just enjoy the music.
•
With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette deck or CD
Player with a single touch.
■ The System incorporates Active Hyper Bass PRO circuitry to faithfully reproduce low frequency sounds.
■ Forty-five-station preset capability (30 FM and 15 AM (MW/LW)) in addition to auto-seek and manual tuning.
■ Versatile CD options include repeat, random and program play.
■ Timer functions; Daily Timer, Recording Timer and Sleep Timer.
■ Auto-reverse tape function.
■ The System is compatible with RDS (Radio Data System) broadcasting. (ONLY FOR UX-V20R.)
•
•
The EON data enables you to standby for desired information.
The PTY Search function searches for programs in the category you wish.
In addition, Radio Text can be displayed using data sent by station.
■ You can connect an audio equipment — used only as a playback device.
How This Manual Is Organized
•
Basic information that is the same for many different functions – e.g. setting the volume – is given in the section “Common Opera-
tions”, and not repeated under each function.
•
•
The names of buttons/controls and display messages are written in all capital letters: e.g. TAPE, “NO DISC”.
The illustrations used in this manual are of UX-V20R.
IMPORTANT PRECAUTIONS
1 Installation of the System
•
•
•
Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C.)
Leave sufficient distance between the System and a TV.
Do not use the System in a place subject to vibrations.
2 Power cord
•
•
•
Do not handle the power cord with wet hands!
Some power is always consumed as long as the power cord is connected to the wall outlet.
When unplugging the System from the wall outlet, always pull the plug, not the power cord.
3 Malfunctions, etc.
•
•
There are no user serviceable parts inside. In case of a system failure, unplug the power cord and consult your dealer.
Do not insert any metallic object into the System.
Table of Contents
Features.................................................................................. 1 Using the Cassette Deck (Recording) ................... 16
How This Manual Is Organized............................................. 1
IMPORTANT PRECAUTIONS ............................................ 1
Using External Equipment.......................................18
Using the Timers ......................................................19
Care and Maintenance .............................................22
Troubleshooting .......................................................23
Specifications ...........................................................24
Getting Started ...........................................................2
Common Operations ..................................................6
Using the Tuner ..........................................................8
Using the CD Player .................................................12
Using the Cassette Deck (Listening to a Tape) ..... 15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Accessories
Make sure that you have all of the following items, which are supplied with the System.
AC Power Cord (1)
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
FM Wire Antenna (1)
If any of these items are missing, contact your dealer immediately.
How to Put Batteries in the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
R6(SUM-3)/AA(15F)
CAUTION: Handle batteries properly.
To avoid battery leakage or explosion:
•
•
•
•
Remove batteries when the Remote Control will not be used for a long time.
When you need to replace the batteries, replace both batteries at the same time with new ones.
Do not use an old battery with a new one.
Do not use different types of batteries together.
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7 m away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
COMPACT
DIGITAL AUDIO
VERTICAL DISC
LOADING MECHANISM
MICRO COMPONENT SYSTEM UX-V20R
STANDBY
AHB
PRO
AUX
REC
VOLUME
TIMER
REV.
MODE
CLOCK
CD
OPEN/CLOSE
Remote sensor
TAPE
FM/AM
CD
PHONES
DOWN
MULTI CONTROL
UP
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Using the supplied Wire Antenna
Rear Panel of the Unit
FM Wire Antenna
(supplied)
R
L
Using the coaxial type connector
(not supplied)
A 75 Ω antenna with coaxial type connector (IEC or DIN 45325)
should be connected to the FM (75 Ω) COAXIAL terminal.
L
R
SPEAKERS
IMPEDANCE
MIN 4Ω
If reception is poor, connect the outdoor antenna.
AC IN
FM outdoor antenna
(not supplied)
Coaxial cable
Note: Before attaching a 75 Ω coaxial lead (the kind with a
round wire going to an outdoor antenna), disconnect the
supplied FM Wire Antenna.
Connecting the AM (MW/LW) Antenna
AM Loop Antenna (supplied)
Rear Panel of the Unit
R
L
L
Attach the AM loop to its base by snapping the tabs on the loop
into the slot in the base.
R
SPEAKERS
IMPEDANCE
MIN 4Ω
ANTENNA
AM EXT
AM LOOP
AC IN
FM (75Ω)
COAXIAL
CAUTION:
To avoid noise, keep antennas away from the
System, the connecting cord and the AC power
cord.
Turn the loop until you have the best reception.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: Make all connections before plugging the System into an AC power outlet.
Connecting the Speakers
For each speaker, connect one end of the speaker wire to the speaker terminals on the back of the System.
1. Open each of the terminals and insert the speaker wires firmly, then close the terminals.
2. Connect the red (+) and black (–) wires of the right side speaker to the red (+) and black (–) terminals marked R on the System.
Connect the red (+) and black (–) wires of the left side speaker to the red (+) and black (–) terminals marked L on the System.
Right speaker (rear side)
Left speaker (rear side)
Black
L
R
SPEAKERS
IMPEDANCE
MIN 4Ω
CAUTION:
If a TV is installed near the speakers, the picture on the TV may be distorted. If this happens, set the
speakers away from the TV.
Connecting External Equipment
You can connect an audio equipment — used only as a playback device.
Connect the audio output terminals on the other equipment and the LINE IN (AUX) terminals on the rear, using an audio cord (not supplied).
Pin-plug x 2
Pin-plug x 2
To audio output
Signal cord (not supplied)
MD recorder or
R
L
cassette deck (not supplied)
LINE IN
(AUX)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC Power Cord
Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit.
AC IN
AC power cord
CAUTIONS:
•
ONLY USE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNCTION OR DAMAGE
TO THE SYSTEM.
•
BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN YOU ARE GOING OUT OR WHEN
THE SYSTEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.
Now you can plug the AC power cord into the wall outlet, and your System is at your command!
COMPU PLAY
The JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment at a single press of the play button
for that function. One Touch Operation turns the power on for you, then starts the function you have specified.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
On the Unit
CD #/8 button
FM/AM button
TAPE @ # button
AUX button
On the Remote Control
CD #/8 button
FM/AM button
TAPE @ # button
AUX button
AUTOMATIC POWER ON
The System automatically turns on with the following operation.
•
When you press the CD OPEN/CLOSE 0 button on the Unit (or CD 0 button on the Remote Control), the System automatically turns
on and the CD cover opens to allow CD insertion. However, this operation does not change the source to CD.
When you press the
button to turn on or off the System, the CD cover will automatically close if it is open.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Operations
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
DISPLAY
UP
CD
FM/AM
8
¥
CD
DISPLAY
MODE
STANDBY
REPEAT
PROGRAM
PTY/EON
UP
AHB
PRO
STANDBY lamp
PHONES
AUX
REC
VOLUME
AHB PRO
VOLUME +, –
CLOCK
SET
TIMER
REV
RANDOM
DOWN
TREBLE
MODE
CLOCK
BASS
AHB PRO
DOWN
AHB
PRO
CD
OPEN/CLOSE
BASS
CANCEL
TAPE
FM/AM
CD
PHONES
VOLUME
TREBLE
DOWN
MULTI CONTROL
UP
VOLUME +, –
REMOTE CONTROL RM-SUXV20R
Turning the Power On and Off
Adjusting the Volume
Press the VOLUME + button to increase the volume or press the
VOLUME – button to decrease it.
Turning the System on –––––––––––––––
Press the
button.
SLEEP
The STANDBY lamp goes out.
The System comes on ready to play the source it was for when the
power was last turned off.
■ For example, if the last thing you were doing was listening to a
CD, you are now ready to listen to a CD again. If you wish,
you can change to another source.
You can adjust the volume level between 0 and 40.
■ If you were listening to the Tuner last, the Tuner comes on
playing the station it was last set to.
CAUTION:
DO NOT turn off (on standby) the Unit with the
volume set to an extremely high level; otherwise
a sudden blast of sound could damage your
hearing, speakers and/or headphones when you
turn on the Unit or start playing any source next
time.
Turning the System off–––––––––––––––
Press the
button again.
The STANDBY lamp lights up.
■ Some power is always consumed even though power is turned
off (called Standby Mode).
■ To switch off the System completely, unplug the AC power
cord from the wall outlet. When you unplug the AC power
cord, the clock will be reset to 0:00.
REMEMBER you cannot adjust the volume level
while the Unit is on standby.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Showing the Clock Time
In Standby mode, the digital clock appears on the display.
Reinforcing the Bass Sound
(AHB PRO)
You can reinforce the bass sound to maintain rich, full bass at low
volume (you can use this effect only for playback):
To get the effect, press the AHB (Active Hyper Bass) PRO
button.
The BASS indicator lights up on the display.
To cancel the effect, press the button again.
The BASS indicator goes out.
When the System is turned on, you can display the digital clock
any time.
To display the digital clock, press the CLOCK button on the
Unit or DISPLAY button on the Remote Control.
Controlling the Tone (Bass/
Treble)
To return to the previous mode, press the same button again.
You can control the tone by changing the bass and treble.
Note: To let the clock work, you need to set the clock beforehand.
(See “Setting the Clock” on page 19.)
Adjusting the bass level –––––––––––––
You can adjust the bass level (low frequency range level) between
–5 and +5. (0: Flat)
1 Press the BASS button on the Remote
Control.
2 Press the UP or DOWN button on the
Remote Control to adjust the bass level.
BASS
DOWN
UP
or
Adjusting the treble level ––––––––––––
You can adjust the treble level (high frequency range level)
between –5 and +5. (0: Flat)
1 Press the TREBLE button on the Remote
Control.
2 Press the UP or DOWN button on the
Remote Control to adjust the treble level.
TREBLE
DOWN
UP
or
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tuner
STANDBY
AHB
PRO
AUX
VOLUME
REC
TIMER
REV
CLOCK
MODE
FM MODE
AUTO PRESET
FM
MODE
AUTO
PRESET
CD
SLEEP
AUX
DISPLAY
TAPE
OPEN/CLOSE
TAPE
FM/AM
CD
CD
PHONES
FM/AM
FM/AM
DOWN
MULTI CONTROL
UP
FM/AM
¢
DISPLAY MODE*
>
SET
CD
¢
4
*PTY/EON
<
DISPLAY
MODE
REPEAT
PROGRAM
PTY/EON
UP
4
SET
RDS indicators (ONLY FOR UX-V20R)
RANDOM
DOWN
TREBLE
UP
AHB
PRO
BASS
CANCEL
DOWN
FM mode indicators
MONO STEREO
EON TA NEWS INFO
VOLUME
REMOTE CONTROL RM-SUXV20R
* ONLY FOR UX-V20R
Band display, Frequency
display, Preset channel
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
You can listen to FM and AM (MW/LW) stations. Stations can be
tuned in manually, automatically, or from preset memory storage.
■ Before listening to the radio:
OR
■ Preset Tuning using the Remote Control (Possible
only after presetting stations)
•
Make sure that both the FM and AM (MW/LW) antennas
Select the desired preset number using the UP, DOWN, > or <
button on the Remote Control. After 1 second the display will
show the preset number’s band and frequency.
Example: Press the UP button until the preset number 12
“P-12” appears.
are correctly connected. (See page 3.)
One touch radio ––––––––––––––––––––––
Just press the FM/AM button to turn on the System and start
playing the station you were last tuned to.
UP
DOWN
■ You can switch from any other sound source to the radio by
pressing the FM/AM button.
or
(After 1 second)
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM (MW/LW)
Tuning In a Station
stations using the Remote Control.
1 Press the FM/AM button.
The band and frequency you were last tuned to appear on the
display.
Note: Preset numbers may have been set to factory test frequen-
cies prior to shipment. This is not a malfunction. You can
preset the stations you want into memory by following one
of the presetting methods below.
(If the last station was selected using the preset number, the
preset number appears first.)
Each time you press the button, the band alternates between
FM and AM (MW/LW).
Presetting stations manually ––––––––
UP
FM/AM
SET
SET
STORED
SET
FM/AM
FM/AM
FM
AM
FM
AM
DOWN
or
(On the Unit)
(On the Remote Control)
(Within 5 seconds)
FM = 30, AM = 15
2 Select a station using one of the follow-
ing methods.
When changing the Band
■ Manual Tuning
1 Select a band by pressing the FM/AM
button.
Press the 4 or ¢ button repeatedly to move from fre-
quency to frequency until you find the station you want.
OR
2 Press the 4 or ¢ button to tune in a
■ Auto Tuning
station.
If you press and hold the 4 or ¢ button for one second or
more, the frequency changes down, or up, automatically until a
station is found.
3 Press the SET button.
“SET” will flash for 5 seconds.
Within 5 seconds, proceed to the next step.
When the display returns to the one set in Step 2 after 5
seconds, press the SET button again.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press the UP, DOWN, > or < button within
5 seconds to select the preset number.
Receiving FM Stations with
RDS
ONLY FOR UX-V20R
You can use the RDS (Radio Data System) by using the buttons on
the Unit and the Remote Control.
UP or > button:
Increases the preset number by 1.
DOWN or < button: Decreases the preset number by 1.
•
When the > or < button is held down, the preset number
changes rapidly.
RDS allows FM stations to send additional signals with their
regular program signals. For example, the stations send their station
names, and information about what type of programs they
broadcast, such as sports or music, etc. This Unit can receive the
following types of RDS signals:
5 Press the SET button within 5 seconds.
“STORED” appears and after 2 seconds, the display returns to
the broadcast frequency display.
6 Repeat above steps 1 to 5 for each sta-
tion you want to store in memory with a
preset number.
PS (Program Service):
shows commonly known station names.
PTY (Program Type):
To change the preset stations, repeat the same steps as above.
shows types of broadcast programs.
RT (Radio Text):
shows text messages the station sends.
EON (Enhanced Other Networks):
provides the information about the types of the programs sent by
other RDS stations.
Presetting stations automatically –––
In each band, you can automatically preset 30 FM and 15 AM
(MW/LW) stations. Preset numbers will be allocated as stations are
found, starting from the lowest frequency and moving up the
frequency.
AUTO
PRESET
What information can RDS signals provide?
FM/AM
The display shows RDS signal information that the station sends.
(For more than 2 seconds)
Showing the RDS signals on the
display––––––––––––––––––––––––––––––––
1 Select a band by pressing the FM/AM
button.
Press the DISPLAY MODE button on the
Remote Control while listening to an FM
station.
2 Press the AUTO PRESET button on the
Remote Control for more than 2 seconds.
Each time you press the button, the display changes to show
information in the following order:
3 Repeat steps 1 – 2 for the other band.
■ If you want to change the preset stations, carry out the Manual
Presetting for the desired preset numbers.
DISPLAY
MODE
PS
PTY
RT
Frequency
CAUTION:
Even if the system is unplugged or if a power
failure occurs, the preset stations will be stored
for about 24 hours. However, in case the preset
stations are erased, you will need to preset the
stations again.
PS (Program Service):
While searching, “PS” appears, then station name is displayed.
“NO PS” appears if no signal is sent.
PTY (Program Type):
While searching, “PTY” appears, then broadcast program type is
displayed. “NO PTY” appears if no signal is sent.
RT (Radio Text):
While searching, “RT” appears, then a text message sent by the
station is displayed. “NO RT” appears if no signal is sent.
Frequency:
Changing the FM Reception
Mode
When you have tuned into an FM stereo broadcast, the STEREO
indicator lights up and you can hear stereo effects.
If an FM stereo broadcast is hard to receive or noisy, you can select
Monaural mode. Reception improves, but you lose any stereo
effect.
Station frequency (non-RDS service)
To search for a program using the PTY codes
REMEMBER you must preset FM RDS stations to use the EON
function. If not yet done, see page 8.
Notes:
Press the FM MODE button on the Remote
Control so that the MONO indicator lights up
on the display.
•
If searching finishes at once, “PS”, “PTY” and “RT” will not
appear on the display.
•
If you press the DISPLAY MODE button while listening to an
AM (MW/LW) station, the display only shows station
frequency.
FM
MODE
•
RDS is not available for AM (MW/LW) broadcasts and for
some FM broadcasts.
STEREO
MONO
To restore the stereo effect, press the FM MODE button on
the Remote Control so that the MONO indicator goes off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
On characters displayed
Descriptions of the PTY Codes
When the display shows PS, PTY or RT signals:
NEWS:
News
•
•
The display shows upper case letters only.
The display cannot show accented letters; For example, “A”
may represent accented “A’s” like “Á, Â, Ã, À, Ä and Å”.
AFFAIRS:
Topical program expanding on the current news or
affairs
Programs on medical service, weather forecasts, etc.
Sports events
INFO:
SPORT:
EDUCATE: Educational programs
DRAMA: Radio plays
CULTURE: Programs on national or regional culture
Searching for a program by PTY
codes –––––––––––––––––––––––––––––––––
One of the advantages of the RDS service is that you can locate a
particular kind of program by specifying the PTY codes.
SCIENCE:
VARIED:
POP M:
Programs on natural sciences and technology
Other programs like comedies or ceremonies
Pop music
To search for a program using PTY or TA codes:
UP
ROCK M:
M.O.R.M:
Rock music
Middle-of-the-road music (usually called “easy
DOWN
listening”)
PTY/EON
PTY/EON
(On the Remote Control)
LIGHT M:
CLASSICS: Classical music
OTHER M: Other music
Light music
or
DOWN
UP
WEATHER: Weather information
(On the Unit)
FINANCE:
Reports on commerce, trading, the Stock Market, etc.
1
Press the PTY/EON button on the Remote
Control once while listening to an FM
station.
CHILDREN: Entertainment programs for children
SOCIAL A: Programs on social activities
RELIGION: Programs dealing with any aspect of belief or faith,
or the nature of existence or ethics
The display alternates between “PTY ” and “SELECT”.
PHONE IN: Programs where people can express their views
either by phone or in a public forum
2 Select the PTY code using the 4 or ¢
button on the Unit (or the UP or DOWN
button on the Remote Control) within 10
seconds.
TRAVEL:
LEISURE:
JAZZ:
Programs about travel destinations, package tours,
and travel ideas and opportunities
Programs concerned with recreational activities
such as gardening, cooking, fishing, etc.
Jazz music
Each time you press the button, the display shows a category in
the following order:
COUNTRY: Country music
NATIONAL: Current popular music from another nation region,
in that country’s language
NEWS Ô AFFAIRS Ô INFO Ô SPORT Ô EDUCATE Ô
DRAMA Ô CULTURE Ô SCIENCE Ô VARIED Ô POP M
Ô ROCK M Ô M.O.R.M Ô LIGHT M Ô CLASSICS Ô
OTHER M Ô WEATHER Ô FINANCE Ô CHILDREN Ô
SOCIAL A Ô RELIGION Ô PHONE IN Ô TRAVEL Ô
LEISURE Ô JAZZ Ô COUNTRY Ô NATIONAL Ô OLDIES
Ô FOLK M Ô DOCUMENT Ô TRAFFIC Ô NEWS
OLDIES:
FOLK M:
Classic pop music
Folk music
DOCUMENT: Programs dealing with factual matters, presented in
an investigative style
TRAFFIC:
Traffic announcement
Classification of the PTY codes for some FM stations
may be different from the above list.
3 Press the PTY/EON button on the Remote
Control again within 10 seconds.
While searching, the display alternates between “SEARCH”
and the selected PTY code.
The Unit searched 30 preset stations and stops when it finds a
station of the category you have selected, then tunes into that
station.
To continue searching after the first stop, press the PTY/
EON button on the Remote Control again while the display
indications are flashing.
If no program is found, “NOTFOUND” appears on the display.
To stop searching at any time during the process, press the
PTY/EON button on the Remote Control.
[Example]
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Case 2: If there is a station broadcasting the program
type you have selected
This Unit tunes to the station broadcasting the program. The
program type (TA, NEWS or INFO) indicator starts flashing.
Switching to a program type of your
choice temporarily –––––––––––––––––––
EON (Enhanced Other Networks) is another convenient RDS
service that allows this Unit to switch temporarily to a broadcast
program of your choice (NEWS, TA or INFO) from the currently
selected station, except if you are listening to a non-RDS station
(all AM (MW/LW) stations or some FM stations).
≠
When the program is over, this Unit goes back to the currently
selected station, but still remains in EON Standby mode.
Case 3: If the FM station you are listening to is broad-
casting the program type you have selected
The broadcast station being currently heard will continue to be
heard. The program type (TA, NEWS or INFO) indicator starts
flashing.
•
•
The EON indicator lights up when tuned to a station which
provides EON information.
If an FM station does not broadcast EON information, EON
cannot be activated.
UP
DOWN
≠
When the program is over, this Unit goes back to the currently
selected station, but still remains in EON Standby mode.
PTY/EON
PTY/EON
(On the Remote Control)
or
DOWN
UP
Notes:
(On the Unit)
•
If the EON is in standby mode and the source (CD, TAPE,
AUX) is changed or the power is switched off, then the EON
mode will be released. When the band is set to AM (MW/LW),
the EON is not activated. When the band is set to FM again, the
EON will be set to standby mode.
1 Press the PTY/EON button on the Remote
Control twice while listening to an FM
station.
The display alternates between “EON” and “SELECT.”
•
When the EON is being operated (i.e. the selected program
type is being received from the broadcast station) and if the
DISPLAY MODE or 4, ¢ button (or the </>/DOWN/UP
button on the Remote Control) is operated, the station will not
switch back to the current selected station even after the
program ends. The program type indicator remains in the
display, indicating that the EON is in standby mode.
When the EON is in standby mode and a radio broadcast is
being recorded, be careful because the EON may be activated
and a different program than the intended one may be recorded.
When the EON mode is not required, release the EON mode.
When the alarm signal is detected by EON, the station
broadcasting the alarm is received with priority. “ALARM” is
not displayed.
2 Select the program type with the 4 or
¢ button on the Unit (or the UP or
DOWN button on the Remote Control)
within 10 seconds.
The display shows a program type in the following order:
•
•
TA:
NEWS:News
Traffic Announcement
INFO: Programs on medical service, weather forecast, etc.
OFF: Canceled
CAUTION:
3 Press the PTY/EON button on the Remote
Control again within 10 seconds to set
the selected program type.
When the sound alternated intermittently be-
tween the station tuned in by the EON function
and the current selected station, cancel the EON
mode. This does not constitute malfunction of
the Unit.
The selected program type indicator lights up on the display,
and the Unit enters EON Standby mode.
Case 1: If there is no station broadcasting the program
type you have selected
The broadcast station being currently heard will continue to be
heard.
≠
When a station starts broadcasting the program you have selected,
this Unit automatically switches to the station. The program type
(TA, NEWS or INFO) indicator starts flashing.
≠
When the program is over, this Unit goes back to the currently
selected station, but still remains in EON Standby mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD Player
COAC
VERTICAL DISC
LOADING MECHANISM
CD Cover
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
7
MICRO COMPONENT SYSTEM UX-V20R
CD
FM/AM
CD #¥8
4
CD 0
STANDBY
AHB
PRO
AUX
REC
CD
VOLUME
¢
DISPLAY
MODE
TIMER
REPEAT
PROGRAM
PTY/EON
UP
REV
UP
>
REPEAT
CLOCK
MODE
SET
CD OPEN/
CD
PROGRAM
RANDOM
<
OPEN/CLOSE
TAPE
FM/AM
CD
RANDOM
DOWN
TREBLE
CLOSE 0
PHONES
SET
CANCEL
DOWN
AHB
PRO
DOWN
MULTI CONTROL
UP
BASS
CANCEL
CD #/8
Track number, Playing time,
Program order number
VOLUME
¢
7
REMOTE CONTROL RM-SUXV20R
4
Music calendar
OVER indicator
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
AALLLL OOVVEERR
PROGRAM RANDOM
Play mode indicator
Repeat indicator
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
Track number exceeding
15 is not displayed.
You can use Normal, Random, Program or Repeat Play. Repeat
Play can repeat all the tracks or just one of the tracks on the CD.
Here are the basic things you need to know to play a CD and locate
the different tracks on it.
3 Press the CD OPEN/CLOSE 0 button on
the Unit (or the CD 0 button on the
Remote Control) again to close the CD
cover.
To close the CD cover and play the CD, you can just press the
CD #/8 button.
■ You can place an 8 cm CD without an adaptor.
■ When a CD with 16 tracks or more is loaded, the OVER
indicator will light up on the display.
•
The quickest way to start a CD is with the one touch
operation
■ Press the CD #/8 button on the Unit or the Remote Control.
•
•
The power is automatically turned on. If a CD is already
inserted, it will start playing from the first track.
If no CD is inserted, “NO DISC” appears on the display and
the CD Player remains in Stop mode.
■ If the CD cannot be read correctly (because it is scratched, for
example), “00 0000” appears on the display.
■ You can insert a CD while listening to another source.
CAUTIONS:
Inserting a CD
•
DO NOT try to open or close the CD cover by
hand as it will be damaged.
1 Press the CD OPEN/CLOSE 0 button on
the Unit (or the CD 0 button on the
Remote Control).
•
When you place or take out a CD, do not let it
fall. Be careful not to scratch your fingers
with the CD cover.
The CD cover opens.
Unloading a CD
Take out the CD as shown below.
2 Place a CD, with its label side out as
shown below. Press down on the portions
around the CD’s center hole until you
hear a click.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press the PROGRAM button.
The System enters the programing mode and the PROGRAM
indicator lights up.
Basics of Using the CD
Player — Normal Play
PROGRAM
Playing a CD––––––––––––––––––––––––––
PROGRAM RANDOM
1 Insert a CD.
5 Press the > or < button to select the track
to program.
> button: Increases the track number by 1.
< button: Decreases the track number by 1.
2 Press the CD #/8 button.
The first track of the CD begins playing.
•
When the > or < button is held down, the track number
changes rapidly.
Track number
Playback time
6 Press the SET button.
•
•
The track number that has already played disappears from the
music calendar.
The CD Player automatically stops when the last track of the
CD has finished playing.
Program order number
SET
To stop playing the CD, press the 7 button.
The following information for the CD is displayed.
Total playback time of the
programed tracks
7 Repeat steps 5 and 6 to select the other
Total track number
Total playback time
tracks for the program.
You can see the total playback time of programed tracks on the
display. You can also see the programed tracks on the music
calendar.
To stop playing and remove the CD, press the CD OPEN/
CLOSE 0 button on the Unit or CD 0 button on the Remote
Control to open the CD cover. Then remove the CD.
To pause, press the CD #/8 button. The playback time flashes on
the display.
8 Press the CD #/8 button.
The System plays the tracks in the order you have programed
them.
To cancel pause, press the same button again. Play continues
from the point where it was paused.
■ You can skip to a particular program track by pressing the 4
or ¢ button (or the </>/DOWN/UP button on the Remote
Control) during Program Play.
■ To stop playing, press the 7 button once.
To confirm the programed tracks while the CD player is
stopped, press the PROGRAM button; the tracks making up the
program will successively be displayed in the programed order.
To delete all the tracks in the program while the CD
player is stopped, press the 7 button. Pressing the CD 0 button
on the Remote Control (or the CD OPEN/CLOSE 0 button on the
Unit) to open the CD cover will also clear the programed tracks.
To exit from the program mode while the CD player is
stopped, press the 7 button to light off the PROGRAM indicator.
All the programed tracks will be cleared.
Selecting a track–––––––––––––––––––––
During playback, press the 4 or ¢ button (or the </>/DOWN/
UP button on the Remote Control) to select the track you want.
The selected track starts playing.
•
Press the ¢ button (or the >/UP button on the Remote
Control) once to skip to the beginning of the next track.
Press the 4 button (or the </DOWN button on the
Remote Control) to skip to the beginning of the track being
played. Press twice quickly to skip to the beginning of the
previous track.
•
•
When the > or < button on the Remote Control is held
down, the tracks are successively skipped.
Selecting a passage within a track ––––
Holding down the 4 or ¢ button (or the DOWN/UP button on
the Remote Control), during playback, will fast-forward/reverse the
CD so you can quickly find a particular passage in the track you
are listening to.
Notes:
•
If the total playback time of the programed tracks exceeds 99
minutes 59 seconds, “-- -- : -- --” appears on the display.
If you try to program the 21st track, “FULL” appears on the
display for about 2 seconds.
•
Programing the Playing
Order of the Tracks
You can program the playing order of the tracks using the
Remote Control.
Modifying the program –––––––––––––––
Modify the contents of the program while the CD Player is stopped.
Each time you press the CANCEL button, the last track in the
program is deleted. To add new tracks to the end of the program,
repeat above steps 5 to 7.
■ You can program up to 20 tracks in any desired order including
the same tracks.
■ You can only make a program when the CD Player is stopped.
1 Insert a CD.
2 Press the CD #/8 button.
3 Press the 7 button to stop the CD.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing at Random
The tracks will play in no particular order when you use this mode.
Press the RANDOM button on the Remote
Control.
The RANDOM indicator lights up on the display, and tracks will
be played in random order.
To skip a track during playback, press the ¢ button (or the
>/UP button on the Remote Control) to jump to the next randomly
selected track. Press the 4 button (or the </DOWN button on the
Remote Control) to jump back to the start of a track being played.
To exit from Random Play mode, press the 7 button.
Repeating Tracks
You can set the program or individual track currently playing to
repeat as many times as you like.
Press the REPEAT button on the Remote
Control.
The Repeat indicator changes at each press of the button, as shown
below.
ALL
blank display
: Repeats one track.
ALL : In Normal Play mode, repeats all the tracks.
In Program Play mode, repeats all the tracks in
the program.
In Random Play mode, repeats all the tracks in
random order.
To exit from Repeat mode, press the REPEAT button until the
Repeat indicator on the display goes out.
■ In Random Play
cannot be selected.
■ Repeat mode remains in effect even when you change the play
mode.
Locking the CD cover
You can lock the CD cover and prohibit to unload the CD.
•
This operation is possible only using the buttons on the unit.
To prohibit unloading the CD, press the button while
holding the 7 button. (If the CD cover is opened, close it first.)
“LOCKED” appears for a while, and the CD cover is locked.
To cancel the prohibition and unlock the CD cover, press
the
button while holding the 7 button.
“UNLOCKED” appears for a while, and the CD cover is unlocked.
Note: If you try to unload the CD, “LOCKED” appears to inform
you that the CD cover is locked.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Cassette Deck
(Listening to a Tape)
STANDBY
AHB
AUX
PRO
VOLUME
Cassette
holder
REC
TIMER
REV
CLOCK
MODE
CD
REV. MODE
OPEN/CLOSE
TAPE
FM/AM
CD
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
AUTO TAPE SELECTOR
AUTO REVERSE
MODE
PRESET
PHONES
TAPE @ #
DOWN
MULTI CONTROL
UP
CD
FM/AM
¢
7
TAPE @ #
TAPE
TAPE 0
CD
¢
7
DISPLAY
MODE
4
REPEAT
PROGRAM
PTY/EON
UP
4
SET
RANDOM
DOWN
TREBLE
Tape Direction indicator
Reverse Mode indicator
AHB
PRO
BASS
CANCEL
VOLUME
REMOTE CONTROL RM-SUXV20R
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
The Cassette Deck allows you to play and record audio tapes.
■ With Automatic Tape Detection, you can listen to type I, II or
IV tapes without having to change any settings.
5 If you need to change the playback direc-
tion, press the TAPE @ # button again.
The other Tape Direction indicator lights up and the tape
playback direction changes.
To stop playing, press the 7 button.
To remove the tape, stop the tape, and press the TAPE 0 button on
the Unit.
The use of tapes longer than 120 minutes is not recommended,
since characteristic deterioration may occur and these tapes
easily jam in the pinch-rollers and the capstans.
One touch play –––––––––––––––––––––––
By pressing the TAPE @ # button on the Unit or the Remote
Control, the Unit will come on, “TAPE” appears on the display,
and if a tape is in the deck, it will start to play. If no tape is loaded,
the Unit will come on and wait for you to insert a tape, or select
another function.
Fast-winding a tape ––––––––––––––––––
■ Press the ¢ or 4 button to fast-wind the tape.
•
The Cassette Deck automatically stops when the tape
reaches its end.
Reverse Mode
You can set the cassette deck to play just one side of a tape, both
sides once, or both sides continuously.
Standard Play
When the power is already on, you can use this basic procedure:
Press the REV. (reverse) MODE button on
the Unit.
The indicator changes at each press of the button as shown.
1 Press the TAPE 0 button on the Unit.
2 When the cassette holder opens, put the
cassette in, with the side you want to
listen to facing up.
•
If the cassette holder does not open, turn the Unit off, then
back on and press the TAPE 0 button again.
: The Cassette Deck automatically stops after playing both
sides of the tape. (Stops when playback in the 2
direction is finished.)
: The Cassette Deck continues to play both sides of the
tape until the 7 button is pressed.
The Cassette Deck automatically stops after playing one
side of the tape.
:
3 Close the holder gently until it clicks.
4 Press the TAPE @ # button.
The tape is played in the direction shown by the Tape Direction
indicator.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Cassette Deck
(Recording)
STANDBY
AHB
AUX
PRO
VOLUME
REC
TIMER
CLOCK
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
REV
MODE
REC
CD
FM/AM
REV. MODE
CD
CD #¥8
7
OPEN/CLOSE
TAPE @ #
TAPE
FM/AM
CD
CD
PHONES
DISPLAY
MODE
TAPE @ #
CD #¥8
Tape Direction indicator
REPEAT
PROGRAM
PTY/EON
UP
DOWN
MULTI CONTROL
UP
7
SET
RANDOM
DOWN
TREBLE
AHB
PRO
BASS
CANCEL
VOLUME
REC
REC indicator
REMOTE CONTROL RM-SUXV20R
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
Reverse Mode indicator
Recording onto a tape from any of the sound sources is simple. Just
place a tape in the Cassette Deck, have the source ready, make one
or two settings, and you’re ready to record. For each source the
procedure is a little bit different so we explain each separately. But
first, here are a few things to make your recordings better.
Standard Recording
You can record any sound source to tape as follows:
1 Insert a blank or erasable tape into the
Cassette Deck.
Things to know before you start
2 If you want to record on both sides of a
tape, press the REV. MODE button on the
recording –––––––––––––––––––––––––––––
■ It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
■ When you want to record onto both sides of a tape, you can set
Reverse mode to do so. Recording automatically stops after
recording in the 2 direction. Therefore, make sure that the tape
direction is 3 when recording with Reverse mode on.
■ The recording level, which is the volume at which the new tape
is being made, is automatically set correctly, so it is not
affected by the VOLUME control on the System. Nor is it
affected by adjusting the sound effects. Thus, during recording
you can adjust the sound you are actually listening to without
affecting the recording level.
Unit until the
indicator is lit.
•
When using Reverse mode, insert the tape so that it will be
recorded in the forward 3 direction.
3 Check the recording direction for the
tape.
Make sure that the Tape Direction indicator is the same as that
for the tape in the Cassette Deck. If the directions are different,
press the TAPE @ # button to correct the tape direction and
then press the 7 button to stop the tape.
4 Prepare the source by, for example,
tuning in a radio station or turning on
connected auxiliary equipment.
Note: For CD recording, refer to “CD Direct Recording” on page
17.
■ Two small tabs on the back of the cassette tape, one for side A
and one for side B, can be removed to prevent accidental
erasure or recording.
Type II detection
slot
5 Press the REC button on the Unit.
Adhesive tape
The REC indicator lights up and the System begins recording.
■ To record on a cassette with the tabs removed, you must cover
the holes with adhesive tape first. However, when a type II tape
is used, only cover part of the hole as shown, since the other
part of the hole (Type II detection slot) is used to detect the
tape type.
Notes for using Reverse mode for recording
When recording in Reverse mode, the System automatically stops
when it reaches the end of the reverse 2 direction. To record on
both sides of a tape, make sure that the recording direction for the
tape inserted is forwards 3, and that the Tape Direction indicator is
also forwards 3, before you start recording.
■ Type I and Type II tapes can be used for recording.
Note: At the start and end of cassette tapes, there is leader tape
which cannot be recorded onto. Thus, when recording CDs
or radio broadcasts, wind on the leader tape first to ensure
that the recording will be made without any music part lost.
To stop at any time during the recording
process
Press the 7 button.
CAUTION:
If a recording you make has excessive noise or
static, the Unit may have been too close to a TV
which was on during the recording. Either turn
off the TV or increase the distance between the
TV and the System.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
One track recording––––––––––––––––––
CD Direct Recording
Everything on the CD goes onto the tape in the order it is on the
1 Insert a blank or erasable tape into the
Cassette Deck.
CD, or according to the order you have set in a program.
2 Play the track on the CD you wish to
record.
1 Insert a blank or erasable tape into the
Cassette Deck.
3 Press the REC button on the Unit.
The CD player returns to the beginning of that track and the
track is recorded on the tape. After recording, the CD player
and Cassette Deck automatically stop.
2 Insert a CD.
3 Press the CD #/8 button.
4 Press the 7 button.
•
If you want to record specific tracks only, program the
tracks beforehand. You can check their total playback time
on the display during programing. (See page 13.)
5 If you want to record on both sides of a
tape, press the REV. MODE button on the
Unit until the
indicator is lit.
•
Make sure that the recording direction for the tape and the
Tape Direction indicator are correct. (See “Notes for using
Reverse mode for recording” on page 16.)
6 Select whether to have pauses left be-
tween recorded selections.
•
If nothing is done, a non-recorded pause of about four
seconds will be automatically left between selections.
If you do not want pauses left between selections, do the
following before proceeding to the next step.
Press the CD #/8 button twice.
•
The CD player enters Pause mode.
7 Press the REC button on the Unit.
The REC indicator lights up and the System begins recording.
•
When recording a CD onto tape with Reverse mode on:
If a song is recorded for more than 12 seconds (which
corresponds to the length of leader tape) but not finished
before the first side of tape comes to an end, this song will
automatically be recorded on the second side from its
beginning to avoid being split on both sides.
If a song is recorded for less than 12 seconds before the
first side of tape comes to an end, the song preceding this
song will also be recorded on the second side from its
beginning as it may not be completely recorded on the first
side because of leader tape.
•
After the CD player has played the entire CD, or all the
programed tracks, the tape automatically stops.
To stop at any time during the recording process, press
the 7 button. The tape stops after 4 seconds.
Note: When making SLEEP timer settings while doing CD Direct
recording, set enough time to allow for the CD to finish
playing, otherwise the power will go off before recording is
completed.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using External Equipment
FM
AUTO
SLEEP
AUX
DISPLAY
TAPE
MODE
PRESET
CD
FM/AM
AUX
CD
DISPLAY
MODE
REPEAT
PROGRAM
PTY/EON
UP
STANDBY
AHB
PRO
AUX
REC
VOLUME
SET
AHB PRO
AUX
TIMER
RANDOM
DOWN
TREBLE
REV
VOLUME +, –
CLOCK
MODE
BASS
AHB
PRO
BASS
CANCEL
CD
OPEN/CLOSE
AHB PRO
TAPE
FM/AM
CD
TREBLE
VOLUME
PHONES
DOWN
MULTI CONTROL
UP
VOLUME +, –
REMOTE CONTROL RM-SUXV20R
Listening to External
Equipment
You can connect an audio equipment — used only as a playback
device.
■ First make sure that the external equipment is properly
connected to the System. (See page 4.)
1 Set the VOLUME control to the minimum
position.
2 Press the AUX button.
“AUX” appears on the display.
3 Start playing the external equipment.
4 Adjust the VOLUME control to the desired
listening level.
5 Apply sound effects, if you wish.
■ Press the AHB PRO button to reinforce the bass sound.
■ Press the BASS/TREBLE button on the Remote Control to
control the tone. (See “Controlling the Tone (Bass/Treble)” on
page 7.)
To exit from AUX mode, select another source.
Notes:
•
For operation of the external equipment, refer to its
Instructions.
•
For recording from the external equipment, refer to “Standard
Recording” on page 16.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
STANDBY
AHB
Timer indicator
FM
MODE
AUTO
PRESET
AUX
PRO
SLEEP
AUX
DISPLAY
TAPE
VOLUME
SLEEP
CD
REC
TIMER
FM/AM
TIMER
CLOCK
REV
ON
SLEEP
CLOCK
MODE
CD
OFF CLOCK
CD
OPEN/CLOSE
DISPLAY
MODE
TAPE
FM/AM
CD
REPEAT
PROGRAM
PTY/EON
UP
PHONES
DOWN
MULTI CONTROL
UP
SET
¢
4
RANDOM
DOWN
TREBLE
AHB
PRO
BASS
CANCEL
VOLUME
ON time, OFF time
REMOTE CONTROL RM-SUXV20R
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
The timers let you control listening and recording functions
automatically.
Setting the Daily Timer
Once you have set the Daily Timer, the timer will be activated at
the same time every day. It can be canceled and re-activate
whenever you wish.
The Timer indicator on the display shows when the Daily Timer
you have set will be activated.
Setting the Clock
When you plug the AC power cord into the wall outlet, the
CLOCK indicator flashes on the display.
•
You can set the clock whether the System is on or off.
Notes:
Notes:
•
Finish each step within 30 seconds. Otherwise, the setting is
cleared and the procedure must be repeated from the beginning.
The clock must be correctly set for the timers to work.
If the clock has not been set, the CLOCK indicator will flash
on the display when you press the TIMER button for more than
2 seconds, and then the display alternates between “ADJUST”
and “CLOCK” for about 5 seconds.
•
•
The clock must be correctly set for the timers to work.
The procedure must be completed within 2 minutes. Otherwise,
•
the setting is cleared and must be repeated from the beginning.
CLOCK
CLOCK
DOWN
UP
or
(For 2 seconds)
1 Press the TIMER button on the Unit for
1 Press the CLOCK button on the Unit for
more than 2 seconds.
more than 2 seconds.
The ON indicator lights up, and then the current ON time
flashes on the display. (Example: 12:00)
The hour digits rapidly flash on the display.
ON
SLEEP
2 Press the ¢ or 4 button to set the
hour.
Pressing the ¢ button moves the hour forwards and pressing
the 4 button moves it backwards. Hold down the button to
move the hour rapidly.
2 Set the ON time. (Example: 12:15)
Press the ¢ or 4 button on the Unit to set the hour you
3 Press the CLOCK button.
want the Unit to come on.
Pressing the ¢ button moves the hour forwards and pressing
the 4 button moves it backwards. Hold down the button to
move the hour rapidly. Press the TIMER button to adjust the
minute.
The minute digits rapidly flash on the display.
4 Press the ¢ or 4 button to set the
minute.
ON
SLEEP
Pressing the ¢ button moves the minute forwards and
pressing the 4 button moves it backwards. Hold down the
button to move the minute rapidly.
3 Set the OFF time. (Example: 13:15)
1. Press the TIMER button on the Unit.
5 Press the CLOCK button again.
The selected time is set and the seconds start counting from 0.
The CLOCK indicator remains lit on the display.
The hour digits of the current OFF time flashes, and then
the OFF indicator lights up on the display.
SLEEP
OFF
CAUTION:
If the System is unplugged, or a power failure
occurs, the timer setting will be lost. You will
need to reset the clock first, then the timer.
2. Press the ¢ or 4 button on the Unit to set the time you
want the Unit to be turned off.
Note: The clock may gain or lose 1 to 2 minutes per month.
Pressing the ¢ button moves the hour forwards and
pressing the 4 button moves it backwards. Hold down
the button to move the hour rapidly. Press the TIMER
button again to adjust the minute.
SLEEP
OFF
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select the music source.
1. Press the TIMER button on the Unit.
“TUNER” flashes on the display.
Setting the Recording Timer
With the Recording Timer, you can make a tape of radio broadcast
automatically.
2. Press the ¢ or 4 button to select the music source you
want to listen to.
The display changes as shown below.
How Recording Timer actually works
The Unit automatically turns on, tunes into the last received station,
and starts recording when the on-time comes. Then, when the off-
time comes, the Unit automatically turns off (stands by).
The timer setting remains in memory until you change it.
Notes:
•
Finish each step within 30 seconds. Otherwise, the setting is
cleared and the procedure must be repeated from the beginning.
The clock must be correctly set for the timers to work.
If the clock has not been set, the CLOCK indicator will flash
on the display when you press the TIMER button for more than
2 seconds, and then the display alternates between “ADJUST”
and “CLOCK” for about 5 seconds.
5 Set the volume level.
•
1. Press the TIMER button on the Unit.
The current volume setting flashes on the display.
2. Press the ¢ or 4 button to select the volume level.
--
: The current volume level will be used.
0 to 40 : When the timer is turned on, the Volume will
be automatically set to the selected level.
SLEEP
1 Press the
tem.
button to turn on the Sys-
2 Tune in to the desired station.
See page 8.
3 Press the TIMER button on the Unit for
6 Press the TIMER button on the Unit.
The timer setting is completed and the display returns to the indi-
cations before you set the timer. The Timer indicator remains lit.
more than 2 seconds.
The ON indicator lights up, and then the current ON time
flashes on the display. (Example: 12:00)
ON
SLEEP
7 Before turning off the System, prepare
the music source selected in step 4.
TUNER: Tune in to the desired station.
REC
TUNER: See “Setting the Recording Timer”.
4 Set the ON time. (Example: 12:15)
CD: Insert a CD.
Press the ¢ or 4 button on the Unit to set the hour you
TAPE: Insert a tape.
want the Unit to come on.
Pressing the ¢ button moves the hour forwards and pressing
the 4 button moves it backwards. Hold down the button to
move the hour rapidly. Press the TIMER button to adjust the
minute.
8 Press the
tem.
To cancel the timer, press the TIMER button for more than 2
seconds. The Timer indicator goes out on the display.
To re-activate the canceled timer, press the TIMER button for
more than 2 seconds to light the Timer indicator. Then, press the
TIMER button until the display returns to the previous indications.
The Timer indicator should remain lit.
To confirm the timer settings, cancel the timer once by
pressing the TIMER button, and press the button again for more
than 2 seconds. Then, press the TIMER button repeatedly, to see
the current timer settings (ON time, OFF time, source, and
volume). Press the TIMER button to set the timer again.
To change the timer setting, repeat the setting procedure from
the beginning.
button to turn off the Sys-
ON
SLEEP
5 Set the OFF time. (Example: 13:15)
1. Press the TIMER button on the Unit.
The hour digits of the current OFF time flashes, and then
the OFF indicator lights up on the display.
SLEEP
OFF
2. Press the ¢ or 4 button on the Unit to set the time you
want the Unit to be turned off.
•
When the timer turns on, the Timer indicator starts flashing.
Pressing the ¢ button moves the hour forwards and
pressing the 4 button moves it backwards. Hold down
the button to move the hour rapidly. Press the TIMER
button again to adjust the minute.
Note: If the Unit is turned on when the timer-on time comes,
Daily Timer does not work.
SLEEP
OFF
CAUTION:
If the System is unplugged, or a power failure
occurs, the timer will be canceled. You will need
to reset the clock first, then the timer.
6 Press the TIMER button on the Unit.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Press the ¢ or 4 button until “TUNER”
appears and the REC indicator lights up
on the display.
Setting the Sleep Timer
When a source is playing, use the Sleep Timer to turn the System
off after a certain number of minutes. By setting the Sleep Timer,
you can fall asleep to music and know that your System will turn
off by itself rather than play all night.
The display changes as shown below.
■ You can only set the Sleep Timer when the System is on.
Note: The clock must be correctly set for the timers to work.
If the clock has not been set, the CLOCK indicator will
flash on the display when you press the TIMER button for
more than 2 seconds, and then the display alternates
between “ADJUST” and “CLOCK” for about 5 seconds.
8 Set the volume level.
1. Press the TIMER button on the Unit.
The current volume setting flashes on the display.
2. Press the ¢ or 4 button to select the volume level.
1 Play a CD or a cassette tape, or tune in to
the desired station.
--
: The current volume level will be used.
0 to 40 : When the timer is turned on, the Volume will be
automatically set to the selected level.
To turn off the volume while the Recording Timer is
working, set the volume level to “0”.
2 Press the SLEEP button on the Remote
Control.
The SLEEP indicator lights up.
3 Set the length of time you want the
source to play before shutting off.
9
Press the TIMER button on the Unit.
The timer setting is completed and the display returns to the indi-
cations before you set the timer. The Timer indicator remains lit.
Note: If you change the station before turning off the System,
the last received station will be recorded.
•
Each time you press the SLEEP button, it changes the number
of minutes shown on the display in this sequence:
10
Canceled
20
30
60
90
10 Insert a blank or erasable tape into the
Cassette Deck.
120
After setting the number of minutes for the Sleep Timer, the
display will stop flashing and return to the previous state.
The System is now set to turn off after the number of minutes you
set.
•
Make sure that the tape has the enough length for recording.
11 Press the
System.
button to turn off the
To cancel the timer, press the TIMER button for more than 2
seconds. The REC and Timer indicators go out on the display.
To re-activate the canceled timer, press the TIMER button for
more than 2 seconds to light the REC and Timer indicators.
To confirm the timer settings, cancel the timer once by
pressing the TIMER button, and press the button again for more
than 2 seconds. Then, press the TIMER button repeatedly, to see
the current timer settings (ON time, OFF time, source, and
volume). Press the TIMER button to set the timer again.
To change the timer setting, repeat the setting procedure from
the beginning.
To confirm the Sleep Time
When the SLEEP button is pressed, the remaining sleep time is
displayed.
To cancel the Sleep Timer setting
Press the SLEEP button until the SLEEP indicator goes out on the
display.
Turning off the System also cancels the Sleep Timer.
•
When the timer turns on, the Timer indicator starts flashing.
Note: If the Unit is turned on when the timer-on time comes,
Recording Timer does not work.
CAUTION:
If the System is unplugged, or a power failure
occurs, the timer will be canceled. You will need
to reset the clock first, then the timer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Handle your CDs carefully, and they will last a long time.
•
If there are fingerprints, etc. on the lens, gently wipe clean with
a cotton swab.
Compact Discs
•
Only CDs bearing this mark can be used with
this System. However, continued use of
irregular shape CDs (heart-shape, octagonal,
etc.) can damage the System.
Moisture Condensation
Moisture may condense on the lens inside the
System in the following cases:
•
•
Remove the CD from its case by holding it at
the edges while pressing the case’s center hole
lightly.
Do not touch the shiny surface of the CD, or
bend the CD.
•
•
•
After turning on heating in the room
In a damp room
If the System is brought directly from a cold to
a warm place
Should this occur, the System may malfunction. In
this case, leave the System turned on for a few
hours until the moisture evaporates, unplug the AC
power cord, and then plug it in again.
•
•
•
Put the CD back in its case after use to prevent
warping.
Be careful not to scratch the surface of the CD
when placing it back in the case.
Avoid exposure to direct sunlight, temperature
extremes, and moisture.
Cassette Tapes
•
If the tape is loose, it may get stretched, cut, or
•
A dirty CD may not play correctly. If a CD
does become dirty, wipe it with a soft cloth in a
straight line from center to edge.
caught in the cassette. Take up the slack by
inserting a pencil in one of the reels and
rotating.
CAUTION: Do not use any solvent (for example,
conventional record cleaner, spray thinner,
benzine, etc.) to clean a CD.
•
•
Do not touch the tape surface.
General Notes
Do not store the tape:
In general, you will have the best performance by keeping your
CDs and the mechanism clean.
-
-
-
-
-
In dusty places
In direct sunlight or heat
In moist areas
On a TV or speaker
Near a magnet
•
Store CDs in their cases, and keep them in cabinets or on
shelves.
•
Keep the system’s CD cover closed when not in use.
Cassette Deck
Cleaning the Lens
•
If the heads, capstans, or pinch-rollers of the Cassette Deck
become dirty, the following may occur:
If the lens in the CD pickup is dirty, sound degradation may take
place.
-
-
-
-
-
Loss of sound quality
Discontinuous sound
Fading
Incomplete erasure
Difficulty in recording
Open the CD cover and clean the lens as shown.
•
Use a blower (available from a camera store) to blow dust off
the lens.
•
Clean the heads, capstans, and pinch-rollers using a cotton
swab moistened with alcohol.
Blower
Lens
Capstans
Pinch-rollers
Erase head
Record/play head
•
•
If the heads become magnetized, the Unit will produce noise or
lose high frequency notes.
To demagnetize the heads, turn off the Unit, and use a head
demagnetizer (available at electronics and record shops).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you are having a problem with your System, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as
your dealer, for service.
•
•
Possible Cause
Action
Symptom
•
•
Connections are incorrect, or loose.
•
•
Check all connections and make
corrections. (See pages 2 – 5.)
Disconnect the headphones.
No sound is heard.
Headphones are connected.
•
•
Antennas are disconnected.
The AM Loop Antenna is too close to
the System.
•
•
Reconnect the antenna securely.
Change the position and direction of the
AM Loop Antenna.
Poor radio reception
•
The FM Wire Antenna is not properly
extended and positioned.
•
Extend FM Wire Antenna to the best
reception position.
The CD is upside down.
Put the CD in with the label side up.
Clean or replace the CD.
The CD does not play.
The CD is dirty or scratched.
The AC power cord is not plugged in.
The CD skips.
Plug the AC power cord.
The CD cover does not open or close.
The cassette holder cannot be opened.
During tape playing, the power cord was
unplugged.
Plug in the power cord, press the
button, and then press the TAPE 0 button.
Cassette record protect tabs are removed.
Cover the holes on the back edge of the
cassette with adhesive tape.
Unable to record.
The built-in microprocessor has malfunc-
tioned due to external electrical interference.
Unplug the System then plug it back in.
Operations are disabled.
•
The path between the Remote Control
and the sensor on the Unit is blocked.
The batteries have lost their charge.
•
•
Remove the obstruction.
Replace the batteries.
Unable to operate the Remote Control.
•
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
UX-V20R (CA-UXV20R and SP-UXV20R)
UX-V10 (CA-UXV10 and SP-UXV10)
Amplifier
Output Power 44 W (22 W + 22 W) at 4 Ω (Max.)
40 W (20 W + 20 W) at 4 Ω (10% THD)
Input Sensitivity/Impedance (1 kHz)
LINE IN (AUX) 400 mV/48 kΩ
Speaker terminals 4 Ω - 16 Ω
Phones 16 Ω - 1 kΩ
0 mW - 15 mW per channel output into 32 Ω
Cassette Deck
Frequency Response
Type I (Normal) 50 Hz - 14 kHz
Type II (CrO2) 50 Hz - 15 kHz
Wow and Flutter 0.15% (WRMS)
CD Player
Signal-To-Noise Ratio 90 dB
Wow And Flutter Immeasurable
Tuner
FM Tuner
Tuning Range 87.5 MHz - 108.0 MHz
AM Tuner
Tuning Range (MW) 522 kHz - 1,629 kHz
(LW) 144 kHz - 288 kHz
Speaker Specifications
(each unit)
Speakers 8 cm cone x 1
Impedance 4 Ω
Dimensions 140 mm x 230 mm x 211 mm (W/H/D)
Mass Approx. 1.8 kg
General
Dimensions 438 mm x 234 mm x 279 mm (W/H/D)
Mass Approx. 6.8 kg
Power Specifications
Power Requirements AC 230 V
, 50 Hz
Power Consumption 50 W (power on mode)
3.7 W (in Standby mode)
Accessories
See page 2.
Design and specifications are subject to change without notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
VICTOR COMPANY OF JAPAN, LIMITED
EN, GE, FR, NL, SP, IT
0100MWMMDWJEM
Download from Www.Somanuals.com. All Manuals Search And Download.
|